Search Results

Search found 336 results on 14 pages for 'seagate'.

Page 8/14 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• Likelihood of a hard drive PCB replacement working?

  - by Grant Limberg

  I have a 1.5TB Seagate 7200.11 that died. The platter still spins up initially when attached to a machine, but then the drive clicks and spins down. Then the cycle repeats. I've found a few sites that sell replacement PCBs, however I don't know if the PCB is the issue, or something else. Given the symptoms above, is it at all likely that a PCB replacement would help? If not, I won't waste my money on the PCB replacement. Note: I put the drive in an external ESATA controller and tried hooking it up to a Linux box here at work and got some error messages in the logs. I can post them if anyone thinks it will help in determining whether a PCB swap would fix the problem I'm running into.

  Read the article

• Data transfer speed to USB storage connected to wifi router very slow

  - by RonakG

  Here is my setup. A Linksys Cisco E3200 wifi router. A MacbookPro running OS X Lion 10.7.4. A Seagate GoFlex 1TB hard drive connected to wifi router via the USB port. When I try to transfer data from my MBP to the HDD, the data transfer rate is very low. I'm getting around 3MB/s write speed. This is very slow compared to the speed I get when HDD is directly connected to the MBP. The HDD is NTFS formatted. And the router provides access to HDD using Samba share. So I connect to the HDD using smb://. What is the limiting factor here affecting the data transfer rate?

  Read the article

• FreeNAS/ZFS/Raid-Z slightly different disks

  - by muskratt

  I'm considering using FreeNAS and "recycling" some of my older 1TB disks. Two are the exact same model Western Digital while another is Seagate and the fourth is Samsung. Typically, since all disks are not equal, I'll create my arrays on a Windows-based server 1GB undersized to prevent a replacement disk not being large enough. Dell is notorious for sending replacement SATA disks of different brand---knock on wood, no problems yet. Since not all drives are created equally and they can vary a few MBs, is there a way to make the the FreeNas/ZFS/Raid-Z function in the same way I do for my Windows-based servers above? Thanks

  Read the article

• Is it wise to use SSHDs (Solid state hybrid drives) on a server?

  - by Seb

  I have a bunch of servers with very heavy I/O that currently use SATA3/SAS drives, but do suffer from I/O wait on the SATA drives, and I have just been alerted to the existence of SSHDs which cost the same for 1TB as the 1TB SATA drives that we currently use. However, previously (until Seagate shipped their first 3.5" SSHD in March) they seemed to be exclusively for Netbooks/Notebooks, which leads me to suspect they're not exactly built for the heavy I/O they'd be in for with my servers. So, would an SSHD give me a performance boost over my SATA3 drives in a heavy I/O environment (such as multiple very large high speed file transfers) or is it best to stick with SATA3 with I/O wait??

  Read the article

• Would hybrid drive work after SSD failure

  - by lulalala

  Hybrid hard drive combines SSD with traditional hard drives. I know that SSD can fail much often than traditional hard drives. So I want to ask that, when the SSD part of the hybrid drive fails, would I still be able to use the traditional hard drive? If it won't work like that, then I will consider add-in SATA cards instead, as it delegates risk much better. EDIT: I guess it differs from model to model, so if yes what models would work. (I am evaluating Seagate DX for now)

  Read the article

• Cloning Windows 2003 Server to new hard drive results in failure

  - by Level1Coder

  Scenario: Old hdd is a Seagate 320gb SATA drive New hdd is a WD 320gb SATA drive Created an exact clone and replaced old hdd with new hdd. Boot up with new hdd, it gets into Windows 2003 server environment but things look weird. Lots of system event failures in the event viewer log. System is barely unusable, critical services are all down. Boot up with old hdd, everything is fine. QUESTION: Is it possible to do a simple clone of a Windows 2003 server system? All I'm changing is the hard drive, everything else stays the same (old CPU/old mobo/etc..)

  Read the article

• Is it normal for a SAS drive to have a few bad blocks, or should I replace my drive ASAP?

  - by Nate

  I have a drive—part of a RAID 1 mirror—that has two bad blocks. Adaptec Storage Manger e-mailed me when it detected the blocks. It shows 4 medium errors for that drive, but state is still “optimal”. This is my first time using Adaptec RAID controllers. I don’t know if an occasional bad block is normal, or if I should immediately replace that drive. Update: The drive failed later the same day! The disk subsystem is: Adaptec 6405 with ZMM (2) Seagate near-line SAS drives (ST31000424SS) The other drive hasn’t reported any bad blocks yet. I am running a consistency check.

  Read the article

• Mac failing (failed?) hard drive - is all hope lost?

  - by Daniel

  It's a 500 GB Seagate laptop hard drive that came with my Macbook Pro. Apple partition format. Already replaced and now have it external, connected via SATA/USB adapter. Trying to get just a few files that I worked on while out of town when it crashed (and thus did not have my time machine backup drive). Drive will not mount, but OS X Disk Utility detects it and can read the capacity, model number, and even the name of the partition, which leads me to believe all hope may not be lost. Failed attempts so far: Disk Utility verify+repair says drive cannot be repaired and that I should back up immediately (lovely) Disk Warrior says it cannot rebuild the directory due to hardware failure Data Rescue quick & deep scans immediately failed PhotoRec says "error reading sector" for every sector (at least for the few minutes I let it run before closing it to explore other options) What else can I try here? Again, I'm just looking for a few, small files (python scripts to be specific) - not a full recovery.

  Read the article

• My NTFS Partition keeps becoming "unusable" on Ubuntu, Any Ideas?

  - by gopherman

  I just purchased a new 2TB Drive External Seagate, My main system uses both Windows and Ubuntu So I am pretty much stuck with keeping my drive as NTFS. I have done this without any problems before but since I got this new drive I have been having issues. When I first load up Ubuntu the drive mounts and runs fine, after an unspecified amount of time i start getting Input/Output errors when accessing the drive. When I goto the Disk Utility I get a message stating the drive is "Unknown or Unused", If I disconnect and reconnect the drive or reboot everything is fine again. There's no errors coming up with S.M.A.R.T and it seems to work fine while under windows. Any thoughts?

  Read the article

• My NTFS Partition keeps becoming "unusable" on Ubuntu, Any Ideas?

  - by gopherman

  I just purchased a new 2TB Drive External Seagate, My main system uses both Windows and Ubuntu So I am pretty much stuck with keeping my drive as NTFS. I have done this without any problems before but since I got this new drive I have been having issues. When I first load up Ubuntu the drive mounts and runs fine, after an unspecified amount of time i start getting Input/Output errors when accessing the drive. When I goto the Disk Utility I get a message stating the drive is "Unknown or Unused", If I disconnect and reconnect the drive or reboot everything is fine again. There's no errors coming up with S.M.A.R.T and it seems to work fine while under windows. Any thoughts?

  Read the article

• Not able to safely remove external disk after having mounted and unmounted a VHD on it

  - by Agnel Kurian

  I am using Windows 7 SP 1. I have an external hard disk (Seagate 500GB) which I am able to use without problems most of the time. I am able to plug it in, use it and then safely unmount it via the "Eject USB Mass Storage Device" option in the taskbar tray. However, if I attach a VHD file located on this disk using "Disk Management", then detach the VHD and finally try to safely disconnect the disk via the system tray, I get an error which says: "Problem Ejecting USB Mass Storage Device: Windows can't stop your 'Generic volume' device because a program is still using it. Close any programs that might be using the device, and then try again later." How do I avoid this problem? Which process could still be accessing the device (even after I have closed the "Disk Management" application) ?

  Read the article

• slow disk writes between host and guest

  - by Jure1873

  I've got a ubuntu (server kernel) on a amd x4, 4gb ram, 2x seagate sata 1 tb disks for testing virtual machines and the write performance is very slow. The two disks are in a software raid1 array, one small boot ext3 partition, 10gb system partition and the rest is a xfs partition (about 980) gb for data (virtual machines). If I'm copying files from the virtual machine to the host with rsync or scp the copy frequently stalls or goes at about 1mb/s. What's wrong? I've tried disabling barriers on xfs, increased logbufs, allocsize, but it seems nothing helps. The strange thing is that await (for example during copying) for sda is usually under 100, while for sdb is around 400. Any ideas on what could be wrong / what could I do to improve this setup?

  Read the article

• Updating ATI HD 5970 Graphics card - version errors?

  - by user55406

  I'm having an issue...My system specs is: Intel i7 960 6GM Corair XMS RAM ATI HD5970 graphics card Intel dx58so motherboard Cooler Master HAF 922 case 1.5TB Seagate hard drive Windows Vista x86 (32-bit). Here is my issue: when I go to AMD/ATI website to update my graphics card - it doesn't. when I type DxDiag and then click on display it tell me my version is 8.17.0 and its on 10.10.0 for the latest version. How can I get 8.17.0 too 10.10.0? I figure it would have done that after I updated the driver for my graphics card. Thanks.

  Read the article

• Tests for hard drive health

  - by Samik R

  I have a 5-year old hard drive (bought new at the time), but it was sitting in my closet for 5 years, unused. I have just started using it, and seems to be getting a whirring sound (rather distinct from the other noises like fans etc.). I ran a few diagnostics tests, like Seagate's SeaTools, and the SMART test, and a few generic tests and all passed. Should I be concerned? Is there any other test that I should run? It's an internal IDE WD 5400RPM drive. Being used for a desktop, which is itself pretty high-end (AMD Phenom II X6 1100T, AMD Radeon GPU etc.), but would be used rather occasionally to begin with (avg. 1-2 hrs. per day). Thanks for any pointers.

  Read the article

• Autoplay for USB drive keeps popping up

  - by Adam Haile

  I have a Seagate external 2TB USB drive that when I leave it plugged in, the Autoplay dialog asking what to do with the drive pops up about once every 30-60 minutes. No matter how many times I tell it to go away, it keeps coming back. I have tried multiple power supplies, USB cables, and all the USB ports on my machine...but it keeps doing the same thing. Also, this does not happen with the same drive on a different computer. Could this be some power or configuration setting that is causing this? I'm running Windows 7 x64 (the computer it works on is x86)

  Read the article

• Different versions of 2.5" drives? Unscreawing Intel 320 for slimmer drive to fit newer thinkpads?

  - by hhh

  My x60s laptops come with about 1-2mm heigher 2.5" HDD than newer x220 models. This is totally stupid when one would like to reuse the old drive in the newer laptops. I bought newer 2.5" 320 Intel SSDs and they seem to have such 1-2mm gap to unscrew but I am unsure whether it is meant for opening. Could someone instruct what to do here? Look the manufacturer has started changing the old good 2.5" drives into slightly different versions, now it means slow compability issues to fix or totally new 2.5" drives. Ideas how to proceed? Unscrewing newer 320 drives or are some other versions of 2.5" drives meant for x220? Does there exist some sort of racks to get drives working between different comps? Perhaps booting from laplink is currently the easiest solution to get things working when changing harddrives between comps? Perhaps related http://www.zdnet.com/blog/hardware/seagate-announced-super-slim-25in-momentus-thin-hard-drive/6439

  Read the article

• External Hard Disk's secter could not be read ?

  - by mgpyone

  I've an 500 GB Seagate External Hard Disk (NTFS) . Currently, I can't open it at Windows. Thus, I've tired with chkdsk command .. but still it stopped and can't continue checking disk.. Also I've tired with fsck on Mac . Then, it shows me the Error .. /Volumes/<HD Name>/ is not a character device CONTINUE? yes /Volumes/<HD Name>/ (NO WRITE) CANNOT READ: BLK 16 CONTINUE? yes THE FOLLOWING DISK SECTORS COULD NOT BE READ: 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, ioctl (GCINFO): Inappropriate ioctl for device fsck: /Volumes/<HD Name>/: can't read disk label The volume I've used is around 300 GB , Thus, it's hard to back up and format again . Thus, any helpful suggestions and solutions will be appreciated pretty well.

  Read the article

• ESXI with non standard hardware HDD issues

  - by Hurricanepkt

  I have 3 very underutilized servers that I am condensing to one of those shuttle PC's with VMWare ESXi The HDD seems to be the bottle neck right now (the light is almost always pure solid) right now I have a single 1TB Seagate 7200.11 connected by SATA. VMWare ESXi cannot detect it when running in AHCI mode, but does when running in IDE mode. I have read that IDE mode can give a 5% performance hit which might give me enough breathing room. However, I am open to setting up an external eSATA or some sort of raid to give me more than just the 5%. I am just weary of sinking some money into a bit of hardware without knowledge of whether it will work. Does anyone know of resources or procedures of how to get this working.

  Read the article

• I recently converted my ex HDD from FAT32 to NTFS. now my pc doesn't find or pick up my NTFS HDD

  - by Jason Haniball

  I recently converted my external hard drive from FAT32 to NTFS using the Command Prompt. Everything was working fine, I copied a 7GB file to it and everything worked. The next day I switched on my PC, I couldn't and still can't find my external 1.5TB hard drive by my computer. I have about 500 to 800 GB of data on it that I really don't want to lose. Its a Iomega Seagate Freeagent HDD. Has no switch, it switched on automatically, don't know if that helps.

  Read the article

• HighPoint RAID Controller can't see drives

  - by Satellite

  I've just built a system with a HighPoint 2720 RAID controller. Everything appears to be OK, except that the controller doesn't see any of my drives - the RAID BIOS displays "ERROR. No Suitable disks". I have tried a WD SATA, Seagate SATA, and OCZ Vertex 3 SATA. I am using MiniSAS to 4x SATA breakout cables. How do I get this working? I've tried to sign up for HighPoint support, but their support site doesn't appear to be functioning correctly.

  Read the article

• scsi and ata entries for same hard drive under /dev/disk/by-id

  - by John Dibling

  I am trying to set up a ZFS pool using 4 bare drives which I have attached to my Ubuntu system via a SATA hot swap backplane. These are Hitachi SATA drives. When I list the contents of /dev/disk/by-id, I see two entries for each drive: root@scorpius:/dev/disk/by-id# ls | grep Hitachi ata-Hitachi_HDS5C3030ALA630_MJ1323YNG0ZJ7C ata-Hitachi_HDS5C3030ALA630_MJ1323YNG1064C ata-Hitachi_HDS5C3030ALA630_MJ1323YNG190AC ata-Hitachi_HDS5C3030ALA630_MJ1323YNG1DGPC scsi-SATA_Hitachi_HDS5C30_MJ1323YNG0ZJ7C scsi-SATA_Hitachi_HDS5C30_MJ1323YNG1064C scsi-SATA_Hitachi_HDS5C30_MJ1323YNG190AC scsi-SATA_Hitachi_HDS5C30_MJ1323YNG1DGPC I know these are the same drives because I wrote down the serial numbers, and all the other drives in this system are either Seagate or WD. The serial number for the first one, for example, is YNG0ZJ7C. Why are there two entries here for each drive? More to the point, when I create my ZFS pool which one should I use; the scsi- one or the ata- one?

  Read the article

• Experience with Intel X25-M 160GB and Oracle

  - by derobert

  We're considering building an Oracle database with 12 Intel X25-M G2 160GB drives in software RAID10. It'd be running Linux. Database gets some very heavy write activity during the early morning data load, other than that it is mostly read-only (and the read load is fairly minimal). We're currently running on 11 150GB Velociraptors (also Linux software RAID10), and are hoping the X25-M will speed up the data load. We currently have redo on different disks than the rest of the data. I'm wondering a few things: Any experience with using X25-M drives for databases? The X25-E are unfortunately beyond our budget. Would it hurt to separate redo off to some magnetic (non-SSD) drives, say 2 (raid1) or 4 (raid10) Seagate Constellations?

  Read the article

• Will installing an Ultra ATA cable backwards affect performance?

  - by GMMan

  I've recently purchased a hard drive upgrade for my Xbox 320GB WD Caviar Blue WD3200AAJB and StarTech.com Ultra ATA/66/100/133 cable IDE66 yes I'm crazy When it came to installing the cable, it was too short (my fault), and there wasn't enough space between the master and slave ends to reach both the DVD drive and the hard drive. The only thing I could do was install the cable backwards and twisting it quite a bit to make it fit. The upgrade works, but reading the manual for the hard drive I replaced (10GB Seagate U Series 5), apparently there is a specific way you have to connect the cable. I don't have that option, so the question comes down to, will my drive performance be at Ultra ATA levels, or is it still performing at original ATA speeds? Is there any way I can test this (benchmarking software for Xbox)?

  Read the article

• Connecting to a 2.5" laptop drive using USB

  - by user27449

  So I swapped my MBP hard drive with a SSD drive, and I want to connect to my old hard drive. I bought a nextstar 3 external 2.5" drive enclosure that has a USB 2.0 interface. I watched an online video of an older version of the enclosure, and in the video they had a ATA cable to connect to the drive. My enclosure didn't come with anything like that, and there doesn't seem to be a way to connect to my drive (my old drive is a seagate 500gb momentus 7200 RPM). My laptop is about 2 years old now (MBP 17"). The drive doesnt' have pins to connect, it has a wide plug type connector, and a USB connector also (I was able to directly plugin the USB cable to the drive, but didn't connect it to my computer, was just testing thigns out). Is it safe for me to directly connect the cable that came with the enclosure to the drive, and then connect the other end to my computer? Does this single cable provide power and data transfer?

  Read the article

• How do I backup (from Vista Home Premium) to a FAT32 HDD connected to a wireless router with no user account or password set?

  - by Scubadooper

  I have a Seagate expansion 2TB HDD which I've managed to get working on my wireless router (thanks to fat32format) however I haven't managed to set my backup to work with it. Vist Home Premium requires that I input a username and password in the backup utility. As far as I'm aware that type of access control isn't set on the HDD: Can I set up the access control on the HDD? If so how Or, can I set the backup to work without it? If so how Thanks for your help, I haven't been able to find the answer anywhere on the net so far

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14  | Next Page >