Search Results

Search found 4396 results on 176 pages for 'wireless extender'.

Page 8/176 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• How to get wireless (Alfa) operate in full power and speed up wireless Internet?

  - by MahboobeAlam

  I am using Wireless to connect to the internet (router). My laptop has Atheros wireless (AR 242x/542x) adapter but the router is a little bit far-away from my room so I have to use an external wireless adapter i.e. Alfa (Realtek 8187) for connectivity. However, since I have started using Ubuntu I noticed that Alfa is not working in full power, internet speed in Ubuntu is much slower than in Windows on my laptop. When I am using Windows 7 the LED (bulb) on Alfa blinks as it should, but when in Ubuntu, it doesn't blink rather it is on but very dim. Connection using Atheros adapter is also the same (slow)... I have tried 4 methods (I found on the Internet) to troubleshoot this matter but no success. It seems to me that Ubuntu/Linux is not letting these wireless adapters to operate in full strength. iwconfig shows that power management is off for both. So what's the problem? Details: ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1e:36:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 TX packets:1657 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:241697 (241.6 KB) TX bytes:241697 (241.6 KB) wlan0 Link encap:Ethernet HWaddr 00:22:5f:9b:24:b5 inet6 addr: fe80::222:5fff:fe9b:24b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:715460 errors:0 dropped:0 overruns:0 frame:0 TX packets:694246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:493539292 (493.5 MB) TX bytes:235159393 (235.1 MB) wlan1 Link encap:Ethernet HWaddr 00:c0:ca:42:14:62 inet addr:192.168.100.102 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:caff:fe42:1462/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:171053 errors:0 dropped:0 overruns:0 frame:0 TX packets:181363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:74094659 (74.0 MB) TX bytes:59474204 (59.4 MB) iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off wlan1 IEEE 802.11bg ESSID:"Zia" Mode:Managed Frequency:2.412 GHz Access Point: 00:0D:F0:9C:A6:18 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-31 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:204 Invalid misc:6610 Missed beacon:0

  Read the article

• Cannot make wireless "forget" networks to which it cannot connect

  - by cboettig

  I see that I can delete networks that my machine "remembers" from nm-applet by clicking on the wireless icon in the panel and selecting "edit connections" - "wireless". However, sometimes I click on the wrong wireless connection by accident in the dropdown list. If the connection is secure, the machine of course never successfully connects, but somehow it still seems to memorize the ESSID. Whenever I'm in range of that wireless, it now tries to connect. Worse, if not connected to any other network, it repeatedly prompts me to connect to this network. If left unattended, I may find dozens of copies of the window prompting me to log in to this mistaken network. There must be a file somewhere that records this connection ID, but I cannot find it. The only connections appearing in the "edit connections" I mention above are those to which I've actually connected. How do I find the file and delete the line corresponding to the offending "memorized" network?

  Read the article

• Wired and Wireless Network Issues with PPPoE

  - by user9054

  down vote favorite Hi Friends, I have got this issue with Ubuntu 10.10. I have been with ubuntu 8.04 and then decided to try out ubuntu 10.10 . I booted with a LiveCD and was able to configure the wireless network painlessly using the livecd. So happily i installed ubuntu 10.10. As soon as ubuntu came up it detected the wireless network and i was able to assign a static IP to eth1 (i dont use DHCP option on my ADSL router) and enter a wap key and use pppoeconf to configure the dialer. The net was on and i was able to surf the net. All hunky dory so far. However on the next boot the fun started. It did not detect the wireless network. I could not see the network manager icon in the systray. I used ifconfig and saw that the entry for eth1 was missing. I used ifup eth1 and it said that eth1 was already up . Then i installed wifi-radar. Wifi-Radar detected the wireless network. I configured wifi-radar for the detected wireless network , set the wap driver as wext and used the manual IP settings. However on clicking connect wifi-radar started looking for a DHCP IP , needless to say it failed. For the love of god i cannot understand why wifi-radar is using DHCP when i have specified manual settings . Next i decided to use the wired network to surf the net looking for a solution . So i plugged in the network cable from my modem , it detected the plugged in connection , i configured eth0 , used pppoeconf and connected to the net. Then i foolishly decided to reboot my PC. And wonders of wonders , the same problem appeared. I cannot see eth0 in my ifconfig anymore. I used pon to start the dsl-provider connection and it said something about network error or something . Now my ifconfig shows only lo , both eth0 and eth1 have disappeared. Can anybody help me on this ? Is it a problem with ipv6 , if so how do you disable ipv6 on ubuntu 10.10 ? OR is this is a known issue with ubuntu 10.10 ? PS : 1) i tried linux mint 10 and had the same issue. On rebooting wireless network was not getting detected . 2) i have made myself the administrator so that there is no issue of rights or anything. Any help is appreciated.

  Read the article

• recent unreliable wireless connection on 10.04 and 10.10

  - by gabkdlly

  Recently, my internet connection over wireless has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista. The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. This problem does not seem to appear when I boot into Ubuntu 9.10 from a live CD ( more precisely, I was able to ping fu-berlin.de for an hour without any packet loss ). Under Ubuntu 10.10, I am experiencing about 33% packet loss. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow ( which happens often ) or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP on the Netgear router and WPA on the TP-LINK to encrypt the wireless connections. Is it possible that someone is jamming my signal ?

  Read the article

• Setting up ubuntu as a wireless accesspoint

  - by nixnotwin

  I have an android phone which doesn't connect to ad-hoc networks. I use ad-hoc network to share internet among my pcs. I want to setup my ubuntu laptop as a wireless access point. But I don't want my ubuntu laptop to be a router as described here as I'll be using suid3 as a http proxy. It should be just a wireless accesspoint which broadcasts it's SSID like a home wireless router. The ubuntu laptop has athros wireless card which requires athk9 driver.

  Read the article

• Wifi - wireless network not working after installing Ubuntu 12.04

  - by Nilesh

  I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• 12.04 disabling wireless via dbus does not work

  - by FlabbergastedPickle

  I am using a proprietary rt3652sta driver for my wireless card. It appears as a ra0 device on the 64-bit Ubuntu 12.04. According to the online documentation the following used to work definitely up to 10.04. dbus-send --system --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.DBus.Properties.Set string:org.freedesktop.NetworkManager string:WirelessEnabled variant:boolean:false This however has no effect on the aforesaid wireless card in 12.04. Also, rfkill does not work as it does not even list the wireless button (again, likely due to the wireless driver being proprietary): rfkill list It only lists the hci0 (bluetooth) one and one can block/unblock it accordingly but this has no effect on the wifi. ifup/down also does not work (AFAICT)... And this leaves me with disabling wireless through the network manager applet. However, trying to do so via dbus appears not to work and yet I would like to automate it via a script. Any ideas how I could find out the proper dbus structure for the call? Is this even possible in Ubuntu 12.04?

  Read the article

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• BCM4313 wireless not working on Dell Inspiron 4010

  - by Mandar

  I have Ubuntu 11.10 installed today and trying to connect to wireless but its not working. It has been working correctly on my Windows 7. i am pretty new to Ubuntu. I tried suggestions listed in this forum but nothing seems to be working for wireless. It shows wireless card listed when I do- sudo lshw -C network: It displays wireless interface as BCM4313. my laptop- Dell Inspiron 4010 Ubuntu- 11.10 Any suggestions? It works when I connect LAN cable to same modem.

  Read the article

• Lenovo e530 no wireless Ubuntu 13.04

  - by Sam

  For some reason my wireless will not work on my Lenovo e530. I am dual booting ubuntu and windows 8 and my wireless works in windows. I saw online that I should run rfkill. I did that but only bluetooth shows up. There is no difference when I press the wireless fn key either, but it does block bluetooth (as it should). I'm really wanting to get into Ubuntu but this is holding me back. To clarify the wireless device does not show at all after running rfkill.

  Read the article

• Why has wireless disappeared after my 12.10 upgrade?

  - by Shay Guy

  I just upgraded to 12.10 on my Lenovo B570 laptop. NetworkManager isn't displaying a submenu for wireless connections at all, even though I downloaded the update through the wireless connection. This displeases me. Stuff I've tried includes: $ sudo modprobe wl FATAL: Module wl not found. $ sudo lspci -nn | grep "BCM" 02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) $ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no ETA: linux-headers-generic is already the newest version, and what I get when reinstalling bcmwl-kernel-source includes the following, near the end. DKMS: install completed. ERROR: Module b43 does not exist in /proc/modules ERROR: Module b43legacy does not exist in /proc/modules ERROR: Module ssb does not exist in /proc/modules ERROR: Module bcm43xx does not exist in /proc/modules ERROR: Module brcm80211 does not exist in /proc/modules ERROR: Module brcmfmac does not exist in /proc/modules ERROR: Module brcmsmac does not exist in /proc/modules ERROR: Module bcma does not exist in /proc/modules FATAL: Module wl not found.

  Read the article

• recent unreliable wireless connection

  - by gabkdlly

  Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

  Read the article

• trying to setup wireless

  - by JohnMerlino

  I'm trying to set up wireless on vostro 1520 dell laptop, with latest Ubuntu install. Here's the output of some of the commands that I was told to run: lshw -C network viggy@ubuntu:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 03 serial: 00:24:e8:da:84:25 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.2.6 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:47 ioport:3000(size=256) memory:f6004000-f6004fff memory:f6000000-f6003fff memory:f6020000-f603ffff *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0e:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:fa000000-fa003fff *-network DISABLED description: Wireless interface physical id: 1 logical name: wlan0 serial: 0c:60:76:05:ee:74 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-29-generic firmware=N/A multicast=yes wireless=IEEE 802.11bg lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 1a:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01) 1a:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) 1a:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. At this point in time, I don't have wireless.

  Read the article

• Dell Inspiron 15R 5520 Wireless Device Not Detected

  - by ashish

  I bought a Dell Inspiron 5520 15R last week and I am a newbie in Ubuntu platform. I installed Windows 7 as well as Ubuntu 12.04 64-bit. But my wireless device is not detected in Ubuntu while it is working fine in Windows OS. My wireless device is Dell Wireless 1704 802.11B 2.4GHZ. Is this a compatibility problem with Ubuntu. What would be the solution? Do I need to install another version of Ubuntu?

  Read the article

• Wireless Disabled (Network Manager)

  - by Peter Kihara

  Am Having issues with My Wireless 1 My laptop had dual boot windows 7 and Ubuntu 13.04 I upgraded to windows 8 and after the first 2-3 reboots all was working well in windows and ubuntu then my wireless in ubuntu stoped working saying "wifi is disabled by hardware switch" the hardware switch has no effect I removed network manager installed new firmwares and still nothing the wifi was not working in a moment of testing I installed wifi radar and this can detect the wireless signals and at one point it connected but still Network manger still says disabled. My Laptop is a HP Pavilion dm4 2070us with Wireless Centrino N 1000 I have updated to 13.10 thinking it would fix it but still nothing

  Read the article

• HP 655 Notebook (Ubuntu 12.04) wireless internet disabled after running updates

  - by Bastian

  Today the update-manaeger suggested that I should download some updates. So I did. After the updates were installed I had to reboot the system. After the reboot my notebook doesn't see any wireless networks. I was looking for a long time on the internet for answers but non of them applies to my case. I have the idea, it has got something to do with the kernel I am currently using (Linux 3.2.0-55). Is this one new for Ubuntu 12.04? When I boot my system I can choose to use an older kernel (linux 3.2.0-32). When I use this one the notebook does see the wireless networks. This is my network card according to the command lspci: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe Anyone an idea to fix my problems with wireless internet?

  Read the article

• My wireless has suddenly became disabled by hardware switch, BIOS, rfkill, fn+f8 do nothing

  - by cwwk

  I have a toshiba l655d-s5145. There is no physical toggle for the wireless, although the f8 key is supposed to do the trick. It doesn't. The wireless has been working since October, and suddenly, nothing. RFKILL reports that the wireless is hard blocked, but unblock wifi, unblock 0, unblock all do nothing. I inserted a usb dongle, and that is also disabled by hardware switch, although rfkill reports that it is neither hard nor soft blocked. My onboard wireless is 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) according to lspci. Lsmod reports that these drivers are loaded. rtl8192c_common 75767 1 rtl8192ce rtlwifi 110972 1 rtl8192ce I resorted to reformatting the drive and reinstalling, but that also did not work. In BIOS I restored system defaults as there is no specific entry for wifi. Before reinstalling a pure xubuntu I went into Unity and saw that the airplane mode was on and despite being toggled off, it returned to the on position. I'm not sure where to find airplane mode in Xubuntu. What else can I do? I need my wireless.

  Read the article

• Marvell TOPDOG (TM) PCI-Express 802.11n Wireless (EC85)

  - by Jareb

  I was running Windows Vista, but hard drive got wipe out and couldn't reinstall it, so I install Ubuntu. My problem is that I cannot get wireless internet. I have search and search, but nothing help or it was too old and the forms got removed. I'm new at Linux. My computer is Gateway M-6752, running a (I believe) Marvell TOPDOG (TM) PCI-Express 802.11n Wireless (EC85), driver. How do I get my wireless working?

  Read the article

• Broadcom Wireless Issues in Lubuntu 14.04

  - by ratxinxaxcage67

  I recently installed Lubuntu 14.04 on my parents' old laptop, and I've been having a super difficult time getting the Broadcom card up and running. I've been following this thread: Installing Broadcom Wireless Drivers ...but I'm still stuck. lspci -vnn | grep Network showed: 06:05.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 02) iwconfig showed: lo no wireless extensions. eth0 no wireless extensions. I've installed b43-firmware-installer and b43-fwcutter and also the linux-firmware-nonfree package. At boot, I keep getting a b43-phy0 error, so I tried sudo rmmod b43, and I got: rmmod: ERROR: Module b43 is not currently loaded I also tried: dmesg | grep b43 [ 17.318405] b43legacy-phy0: Broadcom 4306 WLAN found (core revision 4) [ 17.384870] b43legacy-phy0: Loading firmware b43legacy/ucode4.fw [ 18.046777] b43legacy ssb0:0: Direct firmware load failed with error -2 [ 18.046785] b43legacy ssb0:0: Falling back to user helper [ 18.047858] b43legacy-phy0 ERROR: Firmware file "b43legacy/ucode4.fw" not found or load failed. [ 18.047965] b43legacy-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware (version 3). I went to url it told me to, but it didn't tell me to do anything I haven't already tried. Any help and/or suggestions would be greatly appreciated!

  Read the article

• Slow Wireless Reconnect After Suspend

  - by nrhine1

  I a Broadcom 4312 using the STA drivers, I reinstalled ubuntu because the b43 drivers were giving me a huge hassle along with some weird kernel issues. My wireless speed is fine, everything works well, except upon restart of computer and after taking the computer out of suspend. It takes about 30-45 seconds for the wireless to reconnect, and I think it is a driver issue (I clicked on the network manager at the top and for about 30 seconds there are no wireless networks listed.) I tried this advice already: http://lilserenity.wordpress.com/2007/10/31/fix-ubuntu-dropping-wireless-on-suspendhibernate-resume/ which basically says to change this: STOP_SERVICES="" to STOP_SERVICES="networking" in the file /etc/default/acpi-support This did not help anything. Something to note is that the issue does not occur when I am logging back in after already logging in once and logging out.

  Read the article

• ASUS EeePC Fn+F2 ruins wireless until restart

  - by dawmail333

  I managed to get my wireless working beautifully (ath5k driver working great), and it works over a disable/enable wireless cycle, even a suspend/wakeup cycle (read some people have issues with that). Unfortunately, I discovered that if I press Fn+F2 on my keyboard (Asus EeePC 900HA, so that's the wireless toggle key), wireless then stops working until I restart the computer. How can I fix this? I'm running UNR 10.10 (with Unity turned off tyvm!). I heard something about Jupiter controlling these keys, but what about asus-laptop? How can I fix this behaviour? TIA. (Note, I'm a power user, but still fairly new to Linux. I'm picking up speed though).

  Read the article

• Installing Broadcom Wireless Drivers

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. What are the steps to install Broadcom wireless drivers for a BCM43xx card? I'm a user with no advance knowledge in Linux, so I would need clear explanations on how to make, compile, etc. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] iwconfig showed: lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Driver for asus wireless PC card WL-100GE

  - by emab

  I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Wireless network disabled

  - by neil delmonte

  After installing Ubuntu 11.04, my network has become disabled. Here is the output oflshw in terminal: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 00:21:00:58:65:5f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:d4600000-d4603fff

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >