Search Results

Search found 340 results on 14 pages for 'wlan'.

Page 8/14 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• Dell Vostro 2420 upgrade to 12.04.1 no wifi

  - by Kane

  I have installed 12.04 on a dell vostro 2420 (previously 11.10) and wifi is gone now but wired network remains. I've reviewed the other questions and tried some stuff but no luck yet. The following is the process so far so hopefully someone can help: After installing 12.04 using the additional drivers utility did not bring up any proprietary drivers and using synaptic on installation then reinstallation of bcmwl-kernel-source and b43-fwcutter does not help bring up any drivers either (tried rebooting after as well) I have made sure in the bios that the wlan is turned on, and it appears the laptop does not have a wireless hardware switch, only the keyboard function shortcut which turns bluetooth on and off on the taskbar but there is no lightup of the wireless function on the laptop itself. Dell does not appear to have any drivers for ubuntu and google does not appear to be much help :( Thanks in advance!

  Read the article

• Wireless speed drops over time and doesn't get up if not reconnected

  - by Vili Lehto

  I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• Unable to connect to wireless network

  - by Mike

  A real newbie here. Just downloaded Ubuntu 12.10, put on USB stick and have booted it on my other PC after modifying the boot sequence to boot from USB before hard drive where Windows XP lives. Have no problems with Windows and my wireless but not with Ubuntu. The PC is a Dell Latitude D630 laptop. According to Windows XP , the wireless card is a Dell Wireless 1490 Dual Band WLAN Mini-Card, my IP address is 192.168.0.193, subnet mask is 255.255.255.0, assigned by DHCP, SSID is HOME , type 802.11 and default gateway is 192.168.0.1. Ok, back to booting from USB and TRY option, I am Editing Network connections, I have created/configured "Wireless connection 1" with SSID of HOME and the only other thing I have changed is on the "Editing IPV4 routes for Wireless connection 1 I have enterred 192.168.0.193 , netmask 255.255.255.0 and gateway 192.168.0.1 Anyways , no go. Could use some help. Thanks, Mike from Montreal

  Read the article

• RTL8192SU-based Wi-Fi adapter disconnects permanently

  - by leventov

  I've already tried all possible (http://ubuntuforums.org/showpost.php?p=10129571&postcount=43) solutions, no progress. I'm in despair. In Windows (on the same machine) this adapter works stably. Device: Trendnet TEW-649UB. System details: Ubuntu 11.10; leventov@leventov-ubuntu:~$ uname -a Linux leventov-ubuntu 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux leventov@leventov-ubuntu:~$ lsusb ... Bus 002 Device 002: ID 0bda:8172 Realtek Semiconductor Corp. RTL8191S WLAN Adapter ... leventov@leventov-ubuntu:~$ dmesg | grep 8712 #current driver [ 8.146510] r8712u: module is from the staging directory, the quality is unknown, you have been warned. [ 8.147113] r8712u: DriverVersion: v7_0.20100831 [ 8.147124] r8712u: register rtl8712_netdev_ops to netdev_ops [ 8.147127] r8712u: USB_SPEED_HIGH with 4 endpoints [ 8.147478] r8712u: Boot from EFUSE: Autoload OK [ 8.551272] r8712u: CustomerID = 0x0000 [ 8.551275] r8712u: MAC Address from efuse = 00:14:d1:6c:52:19 [ 8.551625] usbcore: registered new interface driver r8712u [ 9.501351] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin" [ 10.160471] r8712u: 1 RCR=0x153f00e [ 10.161241] r8712u: 2 RCR=0x553f00e leventov@leventov-ubuntu:~$ lsmod | grep 8712 r8712u 189049 0 t

  Read the article

• Wifi problem in ubuntu using macbook pro when it restart

  - by Amro

  I was read that subject : http://ubuntuforums.org/showthread.php?t=2011756 and i follow it step by step in the page n 1 , then i was connect but after i restart my macbook again , i was lost the wifi connection.i dont know why or whats the problem exactly. every time I run this command: dmesg | grep -e b43 -e bcma I get this output: [ 2012.769684] bcma-pci-bridge 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2012.769701] bcma-pci-bridge 0000:02:00.0: setting latency timer to 64 [ 2012.769775] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x25, class 0x0) [ 2012.769808] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1D, class 0x0) [ 2012.769889] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x13, class 0x0) [ 2012.770175] bcma: PMU resource config unknown for device 0x4331 [ 2012.824527] bcma: Bus registered [ 2012.831744] b43-phy0: Broadcom 4331 WLAN found (core revision 29) [ 2013.371031] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07) and to get the connection again every time i must entery that code in the step of reload driver. How i can let the ubuntu see my wifi and wireless device automatically when i reboot my computer????

  Read the article

• Regular wireless dropouts on new lenovo T440s in Ubuntu 14.04

  - by user290670

  Over the last 24 hours my wireless has dropped out regularly. I've tested to make sure it isn't my router (my phone and everyone in the house isn't having problems using the wifi). This is a brand-new installation of Ubuntu 14.04 and according to uname I'm running kernel 3.13.0-24-generic. Now, my laptop has an Intel 7260AC dual band wireless card and I've read that Ubuntu has been having trouble with these. I notice that at http://www.intel.com/support/wireless/wlan/sb/CS-034398.htm There are some updated drivers for my kernel version. However I have no idea how to update the kernel to use these drivers instead so that I can see if this will fix it. Can anyone help? These dropouts are really annoying. EDIT: Upgrading to 3.14.6 did not help.

  Read the article

• Get phone number of (via mobile networks) browsing mobile device

  - by TrialUser

  I recently figured out, that the web site of my phone provider (mobile) mysteriously identifies me and automatically logs me into my account when I'm accessing with my android phone, as if it knew my phone number. (I used several browsers. When I'm using the phone as WLAN hotspot and access the same site from another device that doesn't happen.) How does my phone provider do that? On the one hand, as a programmer, I'd like to be able to do that too, but on the other hand, as a user, I'm kind of scared. What information do they have, such that they (believe they) are able to identify me just by my device? I hope this question isn't completely inappropriate for this site; feel free to add better tags — it's hard to find the right ones without knowing the Webmasters site at all.

  Read the article

• 12.04 in Virtualbox is keep losing my wireless connection

  - by Derek

  I've Windows 7 as the Host OS, Ubuntu 12.04 as the guest and a Netgear WG111v2 as the USB Wireless device. Its connected to an open Wi-Fi network at work to bypass my works crazy strict filtering, When on the domain. I currently have network eth0 turned off in the virtualbox settings so the only network source would be through the USB device at wlan1. Its odd but the wireless seems extremely temperamental, I constantly have to ifconfig wlan down then ifconfig wlan1 up to get it back online. I know this might be super vague just curious if anyone has tried something like this or run into anything like it to point me in a direction I might not be seeing.

  Read the article

• Slow wireless about 1/3 bandwidth of wired from cable modem

  - by Rhino

  HP DV6000 Wireless G Broadcom Netgear WNDR3400 router properly configured. Windows laptops using wireless G and N are considerably faster than mine. 12.04 LTS, all restricted drivers and all up to date. 50Mbps wired and 9-21 Mbps wireless on Ubuntu. 00:14.0 Bridge [0680]: NVIDIA Corporation MCP51 Ethernet Controller [10de:0269] (rev a3) Subsystem: Hewlett-Packard Company Presario V6133CL [103c:30b7] Kernel driver in use: forcedeth 03:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11a/b/g [14e4:4312] (rev 02) Subsystem: Hewlett-Packard Company Broadcom 802.11a/b/g WLAN [103c:1370] Kernel driver in use: wl

  Read the article

• Wireless Not Working with Drivers Installed

  - by Haoran

  I'm new to Linux. I installed Ubuntu 12.10 on my old Compaq/Hp Preario V3000 to replace Windows XP. Every thing works fine except I'm getting no wireless network options in the network drop down menu. I'm using a cable at the moment. Wirless chipset is: 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02) I ran rfkill: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no I also ran iwconfig and got this lo no wireless extensions. eth0 no wireless extensions. In the additional drivers it says: "Using Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source (proprietary)" Any help to resolve the problem would be greatly appreciated.

  Read the article

• Problem with keyboard and trackpad on ubuntu 12.04

  - by Cdub

  Have a really strange issue with my keyboard and trackpad after installing ubuntu 12.04. It picked up both fine with the livecd and in the install, but for quite awhile now, I find when I power my laptop up (Toshiba Satellite L775D-S7132), when I hit the login screen much of the time I won't have any keyboard or touchpad. I can plug in a usb mouse and then at least restart or shut the laptop down and then keep trying until it picks it up correctly, but it's really a pain to have to do that all the time. Are there quite a few bugs related to keyboard and trackpad issues with the new version? I really want to get this issue resolved as it's a major nuisance. Otherwise, my hardware gets picked up fine. Video, audio, wlan, usb work perfectly and I don't ever have any issues with them. What's the best way to figure out the problem? Thanks in advance, C.

  Read the article

• Ubuntu 12.04, Intel Centrino 1030 Wireless-N 1030 not able to connect to wireless

  - by playcat

  I saw several similar threads, but none really does it... I have 12.04 precise x64 installed and things worked great for some 10 days. Then it all stopped - I wasn't able to connect any more. Even more, things were so scre*ed up that it were showing other network's name while connecting :( I have an Asus K53SM-SX054. Here's the text from dmesg related to my card: http://fixee.org/paste/iaw23iw/ Basically, it's Intel Centrino Wireless-N 1030. Not sure if it's important, I had Gnome with unity and then moved to KDE. Any ideas what to do? I'm on the verge of reinstalling things, but I already set plenty of things and have some things that I'd need to back up... and I'm rather lazy to go on with it :) EDIT: My wlan network is hidden. Not sure if this should have any influence.

  Read the article

• networkprinting with cups in ubuntu 13.10

  - by gero

  I upgraded from Ubuntu 13.04 to Ubuntu 13.10. The printer configurations were transferred correctly. I have an USB laser printer, which still works if I connect my laptop directly. Usually I used this printer by wlan or bluetooth, where an old laptop works as server (cups 1.3.X). If I now want to print some pdf or postscript file, one or the other way I only obtain a header printed, not the content of the file. Curiously the Ubuntu 13.10 test page is printed correctly.

  Read the article

• If I enable/disable my wireless device, my computer will panic

  - by Yinyanghu

  Now, I use Debian 6.0.6 instead of Fedora 16/17. But I still sustain the problem of my wireless problem. If I enable/disable my laptop wireless device or my usb wifi adaptor, my laptop will panic. It seems like all the processes stop at that time and I have to restart my laptop directly. P.S. I think I installed the drivers correctly and the linux kernel may have some bugs. For example, when I unplug my usb wifi adaptor or I use this command, ifdown wlan0 I encounter this problem. Wireless Device: PCI: 03:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01) USB: Bus 002 Device 005: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• How to Remove Soft Blocks Permanently in Ubuntu 12.04 LTS?

  - by BBN

  I am using Ubuntu 12.04 LTS on an Asus Eee PC 1000HA. Since I upgraded to 12.04, I have had problems connecting to wifi. When I fly, I need to disable wifi. When I try to reconnect, the "enable networking" option is no longer available. If I type in the terminal "rfkill list", the following shows up: 0: eeepc-wlan: Wireless LAN Soft blocked: yes Hard blocked: no If I type "rfkill unblock all", "enable networking" will become available and I am able to connect to wifi. How can I permanently remove this annoying Soft Block? I don't want to be typing up two lines of code. Any help would be greatly appreciated.

  Read the article

• How to get wireless and wired network working again on my Dell Inspiron 1501?

  - by Angelo Daul

  My wireless doesn't work with Ubuntu 12.04.(it worked with 10.04 LTS) I have a Dell Inspiron 1501. I followed the steps posted below:(from a similar tag, but...) sudo apt-get install --reinstall bcmwl-kernel-source broadcom-sta-common broadcom-sta-source echo "blacklist brcmsmac" | sudo tee -a /etc/modprobe.d/blacklist.conf echo "blacklist bcma" | sudo tee -a /etc/modprobe.d/blacklist.conf ....and now i have no Network device on my PC(wired or wireless) I can use wired conection if i start my laptop with a"previsious version of Linux"...2.26.43... I am a beginner in Linux These are my hardware: 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [ 14e4:4311] (rev 01) 08:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [ 14e4:170c] (rev 02)

  Read the article

• Convert Console Output to Array

  - by theundertaker

  Using netsh wlan show networks mode=bssid on Windows CMD yields a listing of available wireless networks. Is it possible to convert the list, which looks something like this: Interface name : Wireless Network Connection There are 11 networks currently visible. SSID 1 : Custom Gifts Memphis Network type : Infrastructure Authentication : Open Encryption : WEP BSSID 1 : 00:24:93:0c:49:e0 Signal : 16% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 6 9 12 18 24 36 48 54 SSID 2 : airportthru Network type : Adhoc Authentication : Open Encryption : None BSSID 1 : 62:4c:fe:9c:08:18 Signal : 53% Radio type : 802.11g Channel : 10 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 3 : belkin.ffe Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 08:86:3b:9c:8f:fe Signal : 23% Radio type : 802.11n Channel : 1 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 4 : 3333 Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 00:0f:cc:6d:ba:ac Signal : 18% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 22 24 36 48 54 BSSID 2 : 06:02:6f:c3:06:27 Signal : 20% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 5 : linksys Network type : Infrastructure Authentication : Open Encryption : None BSSID 1 : 98:fc:11:69:35:46 Signal : 38% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 6 : iHub_0060350392e0 Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 00:c0:02:7d:5f:4e Signal : 18% Radio type : 802.11g Channel : 11 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 7 : TopFlight Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : 00:14:6c:7a:c4:70 Signal : 16% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 8 : 2WIRE430 Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : b8:e6:25:cb:56:a1 Signal : 16% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 9 : LUBIN Network type : Infrastructure Authentication : WPA-Personal Encryption : TKIP BSSID 1 : 00:13:10:8d:a7:32 Signal : 65% Radio type : 802.11g Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 10 : TV2 Network Network type : Infrastructure Authentication : WPA2-Personal Encryption : CCMP BSSID 1 : b8:c7:5d:07:6e:cf Signal : 79% Radio type : 802.11n Channel : 11 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 SSID 11 : guywork Network type : Infrastructure Authentication : Open Encryption : WEP BSSID 1 : 00:18:e7:cf:02:20 Signal : 15% Radio type : 802.11n Channel : 6 Basic rates (Mbps) : 1 2 5.5 11 Other rates (Mbps) : 6 9 12 18 24 36 48 54 ... into an array using JavaScript or C#? I know it is but it seems like it may be rather difficult. Are there other avenues of obtaining such network information in the requested format? A JavaScript object would be perfect.

  Read the article

• How to secure the communication between an MSSQL database and a c# administrative tool?

  - by citronas

  How can I secure the communication between a C# programm running locally on my computer and a MSSQL Server in a hosted environment? I have an asp.net application that is secured by SSL encryption. So using the asp.net from an open wlan connection is no problem. How can I achieve the same kind of encryption for my administrative tool? Would it be best to write a service? But how would that connection to the service be secured?

  Read the article

• DD-WRT RIP2 Router mode configuration

  - by Eduardo

  Can anybody tell me why my wireless router only redirects traffic to ADSL modem when it is on Gateway mode? These are the configurations when it is on RIP2 Router mode: ADSL Modem: ------------ LAN IP: 10.1.1.1 Subnet mask: 255.0.0.0 RIP v2 enabled in both directions Route: destination: 192.168.1.0 Subnet mask: 255.255.255.0 Gateway: 10.1.1.2 Wireless Router (DD-WRT) ------------------------ WAN IP: 10.1.1.2 WAN Subnet mask: 255.0.0.0 LAN IP: 192.168.1.1 LAN Subnet mask: 255.255.255.0 Operating mode: RIP2 Router Static Route: Destination LAN NET: 10.0.0.0 Subnet Mask: 255.0.0.0 Gateway: 10.1.1.1 Interface: LAN & WLAN

  Read the article

• how do block websites using Ruckus ZoneDirector

  - by David A. Moody

  In my school we use Ruckus ZoneDirector to control our entire network. I have separate WLANs for faculty, elementary, and secondary. The elementary and secondary networks are set to go offline during recess/lunch breaks, and after school hours. This is working fine. What I need to be able to do is block Youtube access to students while leaving it accessible to teachers (faculty WLAN). Is it possible to do this? Thanks in advance. David.

  Read the article

• How to emulate wireless in Virtualbox?

  - by huahsin68

  I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

  Read the article

• Windows virtual wifi hostednetwork - set max number of clients?

  - by user1327408

  I'm building an app that has functionality that creates on the fly a new virtual wifi utilizing the Windows 7 / 2008 features. I can create it just fine, but am looking how to limit the maximum number of connections. By running a "netsh wlan show hostednetwork" command to view my settings - it shows (by default 100), but it HAS to be somewhere in the registry right? - I can't see any settings available for this either at the command line or using the api - so I have to assume it's stored in the reg. I see vwifi and hostednetwork registry keys in HKLM\System\CurrentControlSet\ - Wlansvc\parameters\hostednetworksettings, etc... but can't find any reference to add a "MaxClients" value (or similar) - would like to limit it to only one connection. Has anyone seen any references to this, or know how to do it?

  Read the article

• VirtualBox networking problem, host XP, guest Debian

  - by Silma

  Hi, I'm trying to set up a development environment in a virtual machine on my laptop, with debian os. I have both lan and wlan available on the host machine, yet I can't connect to the internet using either. As I said the host OS is windows XP and the guest OS will be the latest Debian, we downloaded the business card net install so we need internet access from the beginning, besides we need the virtual machine to be visible on the local network (for my fellow developers). We tried host-only networking, NAT, bridging, with proxy (the local network uses a proxy to connect to the internet) and without proxy, nothing seems to work. What else can we do? Thanks a lot.

  Read the article

• Remote Desktop connection repeatedly aborting

  - by DerKlaus

  I connect to my workplace computer using Remote Desktop. After 1-2 minutes the application freezes to tell me after one more minute that the connection was aborted. It then reconnects. Everything works again for 1-2 minutes. Then the process repeats. Probably Forever. My coworkers do not experience such problems when connecting to the workplace. My workplace computer: Windows 7 32bit My home computer: Windows 7 64bit connected to the internet via WLAN-router with integrated ADSL modem (Linksys WAG200G) Things I already tried to fix the problem: disabled the Windows firewall disabled the other firewall reduced the MTU upgraded the firmware on the router configured port-forwarding to forward all packets to my home computer The problem remains unchanged. What could be the cause of the connection aborts? What else can I try to fix the connection? Thanks in advance.

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14  | Next Page >