Search Results

Search found 7116 results on 285 pages for 'auto roast'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 80/285 | < Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

  • Can only bring up one of two interfaces

    - by mstaessen
    I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

    Read the article

  • can't implement jquery jScrollPane to replace browser's scrollbars

    - by Zack
    I am trying to replace browser's scrollbars with jScrollPane (jQuery), it won't work. Here are two attempts to implement it: a basic attempt, and an attempt to imitate the full page demo for jScrollPane. I've been trying everything I could think of to figure out what didn't work, but couldn't. here is my code: <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd"> <html> <head> <title></title> <!-- styles needed by jScrollPane --> <link type="text/css" href="style/jquery.jscrollpane.css" rel="stylesheet" media="all" /> <style type="text/css" id="page-css"> /* Styles specific to this particular page */ html { overflow: auto; } #full-page-container { overflow: auto; } .scroll-pane { width: 100%; height: 200px; overflow: auto; } .horizontal-only { height: auto; max-height: 200px; } </style> <!-- latest jQuery direct from google's CDN --> <script type="text/javascript" src="http://ajax.googleapis.com/ajax/libs/jquery/1.7.1/jquery.min.js"></script> <!-- the mousewheel plugin --> <script type="text/javascript" src="script/jquery.mousewheel.js"></script> <!-- the jScrollPane script --> <script type="text/javascript" src="script/jquery.jscrollpane.min.js"></script> <script type="text/javascript" id="sourcecode"> $(function () { var win = $(window); // Full body scroll var isResizing = false; win.bind( 'resize', function () { if (!isResizing) { isResizing = true; var container = $('#full-page-container'); // Temporarily make the container tiny so it doesn't influence the // calculation of the size of the document container.css( { 'width': 1, 'height': 1 } ); // Now make it the size of the window... container.css( { 'width': win.width(), 'height': win.height() } ); isResizing = false; container.jScrollPane( { 'showArrows': true } ); } } ).trigger('resize'); // Workaround for known Opera issue which breaks demo (see // http://jscrollpane.kelvinluck.com/known_issues.html#opera-scrollbar ) $('body').css('overflow', 'hidden'); // IE calculates the width incorrectly first time round (it // doesn't count the space used by the native scrollbar) so // we re-trigger if necessary. if ($('#full-page-container').width() != win.width()) { win.trigger('resize'); } }); </script> </head> <body> <div id="full-page-container"> This is the most basic implementation of jScrollPane I could create, if I am not wrong this has all it should take, yet it doesn't work. a little lorem ipsum to make the scrollbars show up: [here come's lot's of lorem ipsum text in the actual page...] </div> </body> </html> The other option is the same, with a link to demo.css and demo.js.

    Read the article

  • Messages Disappeared from Outlook Sent Folder

    - by Bryan
    Two days ago almost all of the messages in my Microsoft Outlook sent folder disappeared. I say "almost all" because only the messages from the past 2 weeks remain. This led me to believe that they must have been "auto archived," but I can't find an archive file that contains my messages. I've checked the folder where Outlook says it archives messages, but there's not much there. I've changed my settings to prevent Outlook from auto-archiving my messages in the future, but still need the ones that have disappeared. Can anybody help me find my missing messages?

    Read the article

  • How do I disable automatic updates on OpenSUSE 12.2

    - by MathematicalOrchid
    For reasons unknown, OpenSUSE seems to have half a dozen different places that mention auto-update. Is there a way I can definitely, permanently, irreversibly disable auto-update so that new software will never, ever, under any circumstances, be installed? Ideally I want to prevent the OS from even connecting to the Internet to see if any updates are available. I've unchecked half a dozen things, but I'm still getting alerts telling me updates are available. I do now want updates! I can't believe this is so hard to turn off... In case it makes any difference, OpenSUSE 12.2 with a GNOME desktop.

    Read the article

  • Network monitoring library, or objects, for a cloud

    - by Andrew Smith
    I am looking for library to support server / switch monitoring, to actually be able to check with the device if it's working OK. However this requires some sort of auto-detection and device support. Basically I need to automatically detect a new device, start monitoring it like CPU and PING. So how do I auto-detect the machine remotely, this is something I need library for. Rackspace has something like this - "Cloud Monitoring API". But is there anything opensource which can be used same way? The Nagios and others doesnt have such API, and the big and expensive systems are too big to handle in public cloud, so there must be some other network monitoring engine with API, which can add a new servers automatically and support user isolation for example so I dont see other servers except mine.

    Read the article

  • How can one automatically logon to multiple user accounts in Windows 2008 R2

    - by DJFriar
    We are running a Windows 2008 R2 Terminal Server. Currently, we have local admin accounts created, one for each client that runs our software (SiteA, SiteB, etc). We need these user accounts to auto logon if the server is rebooted. The accounts need to run a full user environment, as we will login remotely at times via TeamViewer to check processes and makes changes, etc. We are using the Registry Hack method now, but that only allows one account to logon. I've seen a program called LogonExpert, but I've never heard of it so I don't know how trust worthy it is, etc. Is there any other way to auto logon to multiple accounts in our environment? Currently the users are local users, but we could make them domain users if that is required.

    Read the article

  • What process is resurrecting mysqld?

    - by ripper234
    I'm following this guide to reset my mysql root password (I'm on ubuntu). When I kill the mysqld process, it immediately gets resurrected. The parent process ID is 1. How can I find what keeps resurrecting mysqld? $ ps -ef | grep mysql mysql 30136 1 0 07:16 ? 00:00:00 /usr/sbin/mysqld root 30295 30274 0 07:18 pts/0 00:00:00 grep --color=auto mysql $ kill -9 30136 $ ps -ef | grep mysql mysql 30302 1 2 07:18 ? 00:00:00 /usr/sbin/mysqld root 30404 30274 0 07:18 pts/0 00:00:00 grep --color=auto mysql $

    Read the article

  • Windows 7: Screen will power off, or blank and lock, but not both.

    - by Heptite
    For some reason, my Windows 7 (Ultimate, 64bit) laptop will not power off the display and keep it off if I have the screen saver and/or the timed auto-lock enabled. Either the display blanks (and locks) but never powers off, or it powers off for less then a minute, then the back light visibly powers back on and stays on, even though the screen remains blanked until I touch a key or the trackpad. I've tried varying the screen power down time to greater than, less than, and exactly equal to the blank screen/lock time, with no success. Turning the screen saver and the timed auto-lock off does allow the timed display power down in the power settings to work properly. (Note that I am not talking about system sleep or hibernate. I'm talking about when the machine remains running, but only the display should power down.)

    Read the article

  • Excel 2010 started changing my numbers

    - by Going Crazy
    If I type in a 16 digit number (format: number, no decimals) it changes the number on me. Example: 1234567812345678 changes the view to 1234567812345670. If I type it in as a general format it changes the numbers above so it displays 1.23457E+15 but if you click on the cell, the display shows the last digit as a 0 instead of an 8 once again. I opened the file on a different computer and same issue now with it. I have changed the auto correcting and auto formating all to no avail. Help!

    Read the article

  • NSD reply from unexpected source

    - by Ximik
    I have server with NSD. There are MAIN_IP and ADD_IP. When I try to get IP of my site from server I have right output dig @localhost my_site.com But when I try to make this from my PC, I have dig @my_ns_server.com my_site.com ;; reply from unexpected source: MAIN_IP#53, expected ADD_IP#53 (ADD_IP is IP of my_ns_server.com) What should I do? UPD: My interfaces conf auto eth2 allow-hotplug eth2 iface eth2 inet static address xxx.xxx.xxx.234 netmask 255.255.255.252 network xxx.xxx.xxx.232 broadcast xxx.xxx.xxx.235 gateway xxx.xxx.xxx.233 dns-nameservers MY_ISP_IP dns-search MY_ISP_DOMAIN auto eth2:0 iface eth2:0 inet static address xxx.xxx.xxx.124 netmask 255.255.255.0 xxx.xxx.xxx is the same for all IPs

    Read the article

  • Connecte RemoteApp to Exising Session

    - by Fowl
    Due to the slightly retardedness of an app I've got to run, I've got a server auto logging in on boot with the app on auto start. Remote desktop at my leisure to check on its status, etc. Gross, but it works. Now I've tried out RemoteApp which seems to work ok (ie. remotes the notification icon, balloons...) except for the fact that it creates a new session (and therefore instance of my app) - this confuses the heck out of app and it means that if I was using 'full' remote desktop I lose all my state. "Restrict each user to a single session" doesn't work. IIRC "Windows XP Mode" uses RemoteApp and it doesn't seem to have any trouble switching between modes. So how can I connect to a running app?

    Read the article

  • URGENT: help recovering lost data

    - by Niels Kristian
    I have made a directory: sudo mkdir /ssd, the directory was supposed to be mounted to a raid array called md3. This was done by adding /dev/md3 /ssd auto defaults 0 0 to fstab. Then after a while where I had used the directory, I realized that I had forgotten to run sudo mount -a - and then I did, and now the data is gone. I tried to uncomment the line in fstab and run sudo mount -a but that didn't get back my data. What can I do!? CONTENT OF FSTAB: proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/md/0 none swap sw 0 0 /dev/md/1 /boot ext3 defaults 0 0 /dev/md/2 / ext4 defaults 0 0 /dev/md3 /ssd auto defaults 0 0

    Read the article

  • Unable to change IP address for eth0 without restart in Ubuntu

    - by Rodnower
    I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

    Read the article

  • MySQL simple replication problem: 'show master status' produces 'Empty set'?

    - by simon
    I've been setting up MySQL master replication (on Debian 6.0.1) following these instructions faithfully: http://www.neocodesoftware.com/replication/ I've got as far as: mysql > show master status; but this is unfortunately producing the following, rather than any useful output: Empty set (0.00 sec) The error log at /var/log/mysql.err is just an empty file, so that's not giving me any clues. Any ideas? This is what I have put in /etc/mysql/my.cnf on one server (amended appropriately for the other server): server-id = 1 replicate-same-server-id = 0 auto-increment-increment = 2 auto-increment-offset = 1 master-host = 10.0.0.3 master-user = <myusername> master-password = <mypass> master-connect-retry = 60 replicate-do-db = fruit log-bin = /var/log/mysql-replication.log binlog-do-db = fruit And I have set up users and can connect from MySQL on Server A to the database on Server B using the username/password/ipaddress above.

    Read the article

  • How do I expand my <div> to properly fit more vertical content?

    - by CSS_maniac
    Whenever I try to add margin-top: 30px to my box_1 and box_2 <div>, my bottom <div> gets pushed down and disappears. It seems like my wrapper wont expand to fit the content. How do I get a 30px gap between top and box_1/2 and bottom? <html> <head> <title>Circle Motion</title> <link rel="stylesheet" type="text/css" href="styles.css" /> </head> <body> <div id="outer-wrapper"> <div id="wrapper"> <div id="top"> </div> <div id="box_1"> <img src="chrome_400x400.png" /> </div> <div id="box_2"> <img src="firefox_400x400.png" /> </div> <div id="bottom"> <p>All Rights Reserved - CSS_maniac 2012 ©</p> </div> </div> </div> </body> </html> CSS /* My CSS */ html { height: 100% } body { background-color: grey; } #outer-wrapper { height: 100%; width: 1000px; margin: 0px auto; background-color: #EAFFDB; -moz-border-radius: 15px; border-radius: 15px; } #wrapper { height: 100%; width: 960px; margin: 0px auto; background-color: #EAFFDB; overflow: hidden; } #top { width: 900px; height: 110px; margin-top: 35px; margin-left: 30px; margin-right: 30px; background-color: white; -moz-border-radius: 15px; border-radius: 15px; } #box_1 { width: 430px; height: 430px; background-color: white; -moz-border-radius: 15px; border-radius: 15px; float:left; margin-left: 30px; text-align: center; } #box_2 { width: 430px; height: 430px; background-color: white; -moz-border-radius: 15px; border-radius: 15px; float:right; margin-right: 30px; text-align: center; } #box_1 img { margin: 15px 0px; } #box_2 img { margin: 15px 0px; } #bottom { width: 900px; margin: 0px auto 0px auto; text-align: center; background-color: white; -moz-border-radius: 15px; border-radius: 15px; clear:both; } /* Classes */ .clear { clear: both; }

    Read the article

  • Thunderbird 3.0.2 stops automatically checking for email

    - by Chris
    Since upgrading to Thunderbird 3.0.2 on Mac OS X 10.6, Thunderbird will intermittently stop checking for messages automatically. Frequently I am presented with the error "This folder is being processed" when manually checking for mail. Restarting Thunderbird fixes the problem, but I have noticed hours can go by where auto checking isn't working, and restarting shows there were dozens of messages waiting to be delivered in that down time. Occasionally I will see "indexing 1 of 2 messages - 0% complete" in the status bar, it will sit there for a long time. Actions I've taken to fix: Deleted all .msf files in all accounts Removed News & Blogs account Staggered the "automatically check for mail" interval for each account Worth noting: after waking up the macbook, TB usually needs to be restarted to resume auto checking for mail. Has anyone experienced such trouble?

    Read the article

  • Do you know a script for email round trip monitoring?

    - by crazyfr
    Do you know a simple script that can do email round trip monitoring ? I want to monitor email service on A. I install the script on B. B sends an email to A A sends an auto-reply to B B knows that email service is working well. B restarts this test every 30min. If B didn't received replies, it sends an alert message. B could also monitor round-trip delay of emails. I have not access to the email service, I can only ask new end user email and configure auto-reply. B is an Ubuntu. Thanks!

    Read the article

  • Running a home mail server using dynamic dns

    - by user4009
    Hi, Is it possible to run an email server on my home box using dynamic dns? The scenario is, I want to auto cc all incoming and outgoing emails from my one account to another, from some server side config instead of configuring email clients for rules. I have tried Google Apps Mail but it doesn't allow auto cc of outgoing emails. After having read tons of blogs, forum messages etc (hope I have been reading the correct info :) ) the only option to achieve what I am needing is to setup my own mail server, but the cost of getting a static IP doesn't fit my budget. Please can someone point me in the correct direction. Platform doesn't matter, I can setup a Windows or Linux server. Many Thanks

    Read the article

  • Unable chage IP address for eth0 without restart in Ubunto

    - by Rodnower
    I have Ubuntu 12.04.1 installed. I try to change IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4: auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status Now I issue: sudo service networking restart I have response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart IP changing... Any ideas?

    Read the article

  • Input multiple file names in windows open file dialog box

    - by goodiet
    Windows 7 allows you to select multiple files to open at once by using ctrl or shift key. The "File Name" input field at the bottom of the dialog box would auto populate with the following sample: "aaa.txt" "bbb.txt" "ccc.txt" "ddd.txt" I have 14,000 files in a folder and I only need a range of files (approx 500). When I use the shift key to select a range of files, the "File Name" field auto populates all 500 file names. Windows would cut me off at the 260th character when I try to paste in a pre-generated string into the "File Name" field. Is there a way to bypass the 260 character limit so it would accept my entire string with 500 file names?

    Read the article

  • External drives show up in Nautilus/Computer even when they are unplugged.

    - by Testament
    I have two 1TB Seagate USB (sdc1 and sdd1) drives connected to an old PC running Fedora 11 without an X server running. Since sdc1 and sdd1 change depending on the order in which they are plugged in, I decided to mount them using their UUID instead. These are my fstab entries UUID=d1b28578-451b-4f03-af28-2e8a6d5b7efb /media/Seagate ext3 defaults,rw,auto,users UUID=36bf5df4-934e-42d4-9e25-16a13971509c /media/Projects ext3 defaults,rw,auto,users They work fine, but when I unmount them and unplug the USB drives, they still show up in Nautilus (I'm running nautilus with X11 forwarding to an Ubuntu machine, btw). Now if I remove those entries from fstab, the drives disappear from Computer. If I add the entries back, they show up as an unmounted drive even when the drive is not plugged in. How do I do this so they don't show up when they're not plugged in?

    Read the article

  • External drives show up in Nautilus/Computer even when they are unplugged.

    - by Testament
    I have two 1TB Seagate USB (sdc1 and sdd1) drives connected to an old PC without an X server running. Since sdc1 and sdd1 change depending on the order in which they are plugged in, I decided to mount them using their UUID instead. These are my fstab entries UUID=d1b28578-451b-4f03-af28-2e8a6d5b7efb /media/Seagate ext3 defaults,rw,auto,users UUID=36bf5df4-934e-42d4-9e25-16a13971509c /media/Projects ext3 defaults,rw,auto,users They work fine, but when I unmount them and unplug the USB drives, they still show up in Nautilus (I'm running nautilus with X11 forwarding onto another Ubuntu machine, btw). Now if I remove those entries from fstab, the drives disappear from Computer. If I add the entries back, they show up as an unmounted drive even when the drive is not plugged in. How do I do this so they don't show up when they're not plugged in?

    Read the article

  • wmp12 refuses to convert files when syncing

    - by Carbonara
    I have quite a large music collection of MP3s at 320kbps and some WMA files at various bitrates. I'm trying to sync some of them to my HTC Desire and am quickly running out of space. WMP12 has options to set, per device you wish to sync, to auto convert to a lower bitrate whilst syncing. I have set this to auto convert files to a maximum bitrate of 192kbps, that way I can fit more music on the device but keep the files on my PC at the higher rate. See these screens to see that it's set up correctly. Only problem is, surprise surprise for a Microsoft product, it doesn't actually work. Any file that is greater than 192kbps, MP3 or WMA simply fails, doesn't get converted or copied to the device. The message in the sync log displays the rather unhelpful message "error" and that's it. Any help would be appreciated. I'm not really looking for alternative software solutions I'd like to get this working since that's what it's supposed to do.

    Read the article

  • Wifi network stopped being visible (and usable) (Linksys wag320n)

    - by s427
    Basically, my wifi network simply stopped working for no apparent reason. It doesn't appear in the list of the available networks anymore. I can see all my neighbors' networks, but not mine. It's as if it doesn't exist anymore. The internet connection (non-wifi), which goes through the same modem/router, is fine though. I already had a similar problem about one year ago (see here: Wifi network SSID not visible ), just after buying this very modem. I finally got it to work after performing two factory resets and getting rid of the Cisco "Magic" software; but this time it's not working. I use a linksys router-modem (WAG320N) which is directly connected (via network cable) to my desktop computer (Windows 7). I have (mainly) two devices that use the wifi network: my phone (Samsung Galaxy Nexus) and an Asus tablet (TF201, aka Transformer Prime). I also resurrected an old laptop computer (Dell, running Windows XP) to test that, and it doesn't see anything either (apart from the 20 other wifi networks, of course ^^). This wifi network was working just fine and has been for about a year. I haven't touched the modem settings so I have no idea what's causing the problem. I tried: making my phone "forget" about my network, hoping it would see it again after that: no luck. re-entering the network informations (SSID/password) manually on my phone: still no luck (says it's not in range) exporting the modem configuration, resetting the modem (factory reset, via modem admin), restarting it, importing the configuration: nope. factory reset, turning it off for 15 minutes, restarting, re-factory reset, and entering the configuration manually: still nothing. Has anybody experienced something similar before? Have you any suggestion to fix that? Thanks in advance. PS: to clear things up, here are the settings of my modem regarding wifi: Basic wireless settings: Configuration: manual Radio Band: 2.4GHz Wireless Network Mode: B/G/N-Mixed SSID: s427 Channel Bandwidth: Wide - 40 MHz Channel Wide Channel: 9 - 2.452GHz Standard Channel: 11 - 2.462GHz SSID Broadcast: Enable Advanced Wireless Settings AP Isolation: Disable Authentication Type: Auto Basic Rate: Default Transmission Rate: Auto N Transmission Rate: Auto CTS Protection Mode: Disable Beacon Interval: 100 DTIM Interval: 1 Fragmentation Threshold: 2346 RTS Threshold: 2346

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 76 77 78 79 80 81 82 83 84 85 86 87  | Next Page >