Search Results

Search found 2166 results on 87 pages for 'hot spot'.

Page 81/87 | < Previous Page | 77 78 79 80 81 82 83 84 85 86 87  | Next Page >

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Intermittent lockups, unable to diagnose in over a year

  - by Magsol

  Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

  Read the article

• SELF-SOLVED AutoHotkey Function GetMouseTaskbutton need to adapt for 64-bit OS

  - by auntyEEK

  SOLVED VIA SELF-HELP, HAIR-PULLING, AND TEETH-GRINDING. THANKS ANYWAY....... I'm using the GetMouseTaskbutton function from this thread on AHK forum. [http://www.autohotkey.com/forum/topic22763.html&highlight=getmousetaskbutton][1] ; Gets the index+1 of the taskbar button which the mouse is hovering over. ; Returns an empty string if the mouse is not over the taskbar's task toolbar. ; ; Some code and inspiration from Sean's TaskButton.ahk GetMouseTaskButton(ByRef hwnd) { MouseGetPos, x, y, win, ctl, 2 ; Check if hovering over taskbar. WinGetClass, cl, ahk_id %win% if (cl != "Shell_TrayWnd") return ; Check if hovering over a Toolbar. WinGetClass, cl, ahk_id %ctl% if (cl != "ToolbarWindow32") return ; Check if hovering over task-switching buttons (specific toolbar). hParent := DllCall("GetParent", "Uint", ctl) WinGetClass, cl, ahk_id %hParent% if (cl != "MSTaskSwWClass") return WinGet, pidTaskbar, PID, ahk_class Shell_TrayWnd hProc := DllCall("OpenProcess", "Uint", 0x38, "int", 0, "Uint", pidTaskbar) pRB := DllCall("VirtualAllocEx", "Uint", hProc , "Uint", 0, "Uint", 20, "Uint", 0x1000, "Uint", 0x4) VarSetCapacity(pt, 8, 0) NumPut(x, pt, 0, "int") NumPut(y, pt, 4, "int") ; Convert screen coords to toolbar-client-area coords. DllCall("ScreenToClient", "uint", ctl, "uint", &pt) ; Write POINT into explorer.exe. DllCall("WriteProcessMemory", "uint", hProc, "uint", pRB+0, "uint", &pt, "uint", 8, "uint", 0) ; SendMessage, 0x447,,,, ahk_id %ctl% ; TB_GETHOTITEM SendMessage, 0x445, 0, pRB,, ahk_id %ctl% ; TB_HITTEST btn_index := ErrorLevel ; Convert btn_index to a signed int, since result may be -1 if no 'hot' item. if btn_index 0x7FFFFFFF btn_index := -(~btn_index) - 1 if (btn_index > -1) { ; Get button info. SendMessage, 0x417, btn_index, pRB,, ahk_id %ctl% ; TB_GETBUTTON VarSetCapacity(btn, 20) DllCall("ReadProcessMemory", "Uint", hProc , "Uint", pRB, "Uint", &btn, "Uint", 20, "Uint", 0) state := NumGet(btn, 8, "UChar") ; fsState pdata := NumGet(btn, 12, "UInt") ; dwData ret := DllCall("ReadProcessMemory", "Uint", hProc , "Uint", pdata, "UintP", hwnd, "Uint", 4, "Uint", 0) } else hwnd = 0 DllCall("VirtualFreeEx", "Uint", hProc, "Uint", pRB, "Uint", 0, "Uint", 0x8000) DllCall("CloseHandle", "Uint", hProc) ; Negative values indicate seperator items. (abs(btn_index) is the index) return btn_index > -1 ? btn_index+1 : 0 } It identifies the owner of the hovered taskbar button. I'm using it in a routine to auto-activate window by hovering its taskbar button, and also a routine to close inactive window by middle-click on its taskbar button. Works great on my XP machine. The author had stated that the function does work in Vista, but it refuses to work for me in Vista 64-bit, so apparently it is only valid in 32-bit. And I am very new to AHK, and don't know how to adapt it. Unfortunately, my queries at the site sank without a trace. Does anyone have advice for me? I will be most grateful. Thanks.

  Read the article

• First PC Build (Part 1)

  - by Anthony Trudeau

  Originally posted on: http://geekswithblogs.net/tonyt/archive/2014/08/05/157959.aspxA couple of months ago I made the decision to build myself a new computer. The intended use is gaming and for using the last real version of Photoshop. I was motivated by the poor state of console gaming and a simple desire to do something I haven’t done before – build a PC from the ground up. I’ve been using PCs for more than two decades. I’ve replaced a component hear and there, but for the last 10 years or so I’ve only used laptops. Therefore, this article will be written from the perspective of someone familiar with PCs, but completely new at building. I’m not an expert and this is not a definitive guide for building a PC, but I do hope that it encourages you to try it yourself. Component List Research There was a lot of research necessary, because building a PC is completely new to me, and I haven’t kept up with what’s out there. The first thing you want to do is nail down what your goals are. Your goals are going to be driven by what you want to do with your computer and personal choice. Don’t neglect the second one, because if you’re doing this for fun you want to get what you want. In my case, I focused on three things: performance, longevity, and aesthetics. The performance aspect is important for gaming and Photoshop. This will drive what components you get. For example, heavy gaming use is going to drive your choice of graphics card. Longevity is relevant to me, because I don’t want to be changing things out anytime soon for the next hot game. The consequence of performance and longevity is cost. Finally, aesthetics was my next consideration. I could have just built a box, but it wouldn’t have been nearly as fun for me. Aesthetics might not be important to you. They are for me. I also like gadgets and that played into at least one purchase for this build. I used PC Part Picker to put together my component list. I found it invaluable during the process and I’d recommend it to everyone. One caveat is that I wouldn’t trust the compatibility aspects. It does a pretty good job of not steering you wrong, but do your own research. The rest of it isn’t really sexy. I started out with what appealed to me and then I made changes and additions as I dived deep into researching each component and interaction I could find. The resources I used are innumerable. I used reviews, product descriptions, forum posts (praises and problems), et al. to assist me. I also asked friends into gaming what they thought about my component list. And when I got near the end I posted my list to the Reddit /r/buildapc forum. I cannot stress the value of extra sets of eyeballs and first hand experiences. Some of the resources I used: PC Part Picker Tom’s Hardware bit-tech Reddit Purchase PC Part Picker favors certain vendors. You should look at others too. In my case I found their favorites to be the best. My priorities were out-the-door price and shipping time. I knew that once I started getting parts I’d want to start building. Luckily, I timed it well and everything arrived within the span of a few days. Here are my opinions on the vendors I ended up using in alphabetical order. Amazon.com is a good, reliable choice. They have excellent customer service in my experience, and I knew I wouldn’t have trouble with them. However, shipping time is often a problem when you use their free shipping unless you order expensive items (I’ve found items over $100 ship quickly). Ultimately though, price wasn’t always the best and their collection of sales tax in my state turned me off them. I did purchase my case from them. I ordered the mouse as well, but I cancelled after it was stuck four days in a “shipping soon” state. I purchased the mouse locally. Best Buy is not my favorite place to do business. There’s a lot of history with poor, uninterested sales representatives and they used to have a lot of bad anti-consumer policies. That’s a lot better now, but the bad taste is still in my mouth. I ended up purchasing the accessories from them including mouse (locally) and headphones. NCIX is a company that I’ve never heard of before. It popped up as a recommendation for my CPU cooler on PC Part Picker. I didn’t do a lot of research on the company, because their policy on you buying insurance for your orders turned me off. That policy makes it clear to me that the company finds me responsible for the shipment once it leaves their dock. That’s not right, and may run afoul of state laws. Regardless they shipped my CPU cooler quickly and I didn’t have a problem. NewEgg.com is a well known company. I had never done business with them, but I’m glad I did. They shipped quickly and provided good visibility over everything. The prices were also the best in most cases. My main complaint is that they have a lot of exchange only return policies on components. To their credit those policies are listed in the cart underneath each item. The visibility tells me that they’re not playing any shenanigans and made me comfortable dealing with that risk. The vast majority of what I ordered came from them. Coming Next In the next part I’ll tackle my build experience.

  Read the article

• ODEE Green Field (Windows) Part 4 - Documaker

  - by AndyL-Oracle

  Welcome back! We're about nearing completion of our installation of Oracle Documaker Enterprise Edition ("ODEE") in a green field. In my previous post, I covered the installation of SOA Suite for WebLogic. Before that, I covered the installation of WebLogic, and Oracle 11g database - all of which constitute the prerequisites for installing ODEE. Naturally, if your environment already has a WebLogic server and Oracle database, then you can skip all those components and go straight for the heart of the installation of ODEE. The ODEE installation is comprised of two procedures, the first covers the installation, which is running the installer and answering some questions. This will lay down the files necessary to install into the tiers (e.g. database schemas, WebLogic domains, etcetera). The second procedure is to deploy the configuration files into the various components (e.g. deploy the database schemas, WebLogic domains, SOA composites, etcetera). I will segment my posts accordingly! Let's get started, shall we? Unpack the installation files into a temporary directory location. This should extract a zip file. Extract that zip file into the temporary directory location. Navigate to and execute the installer in Disk1/setup.exe. You may have to allow the program to run if User Account Control is enabled. Once the dialog below is displayed, click Next. Select your ODEE Home - inside this directory is where all the files will be deployed. For ease of support, I recommend using the default, however you can put this wherever you want. Click Next. Select the database type, database connection type – note that the database name should match the value used for the connection type (e.g. if using SID, then the name should be IDMAKER; if using ServiceName, the name should be “idmaker.us.oracle.com”). Verify whether or not you want to enable advanced compression. Note: if you are not licensed for Oracle 11g Advanced Compression option do not use this option! Terrible, terrible calamities will befall you if you do! Click Next. Enter the Documaker Admin user name (default "dmkr_admin" is recommended for support purposes) and set the password. Update the System name and ID (must be unique) if you want/need to - since this is a green field install you should be able to use the default System ID. The only time you'd change this is if you were, for some reason, installing a new ODEE system into an existing schema that already had a system. Click Next. Enter the Assembly Line user name (default "dmkr_asline" is recommended) and set the password. Update the Assembly Line name and ID (must be unique) if you want/need to - it's quite possible that at some point you will create another assembly line, in which case you have several methods of doing so. One is to re-run the installer, and in this case you would pick a different assembly line ID and name. Click Next. Note: you can set the DB folder if needed (typically you don’t – see ODEE Installation Guide for specifics. Select the appropriate Application Server type - in this case, our green field install is going to use WebLogic - set the username to weblogic (this is required) and specify your chosen password. This credential will be used to access the application server console/control panel. Keep in mind that there are specific criteria on password choices that are required by WebLogic, but are not enforced by the installer (e.g. must contain a number, must be of a certain length, etcetera). Choose a strong password. Set the connection information for the JMS server. Note that for the 12.3.x version, the installer creates a separate JVM (WebLogic managed server) that hosts the JMS server, whereas prior editions place the JMS server on the AdminServer.  You may also specify a separate URL to the JMS server in case you intend to move the JMS resources to a separate/different server (e.g. back to AdminServer). You'll need to provide a login principal and credentials - for simplicity I usually make this the same as the WebLogic domain user, however this is not a secure practice! Make your JMS principal different from the WebLogic principal and choose a strong password, then click Next. Specify the Hot Folder(s) (comma-delimited if more than one) - this is the directory/directories that is/are monitored by ODEE for jobs to process. Click Next. If you will be setting up an SMTP server for ODEE to send emails, you may configure the connection details here. The details required are simple: hostname, port, user/password, and the sender's address (e.g. emails will appear to be sent by the address shown here so if the recipient clicks "reply", this is where it will go). Click Next. If you will be using Oracle WebCenter:Content (formerly known as Oracle UCM) you can enable this option and set the endpoints/credentials here. If you aren't sure, select False - you can always go back and enable this later. I'm almost 76% certain there will be a post sometime in the future that details how to configure ODEE + WCC:C! Click Next. If you will be using Oracle UMS for sending MMS/text messages, you can enable and set the endpoints/credentials here. As with UCM, if you're not sure, don't enable it - you can always set it later. Click Next. On this screen you can change the endpoints for the Documaker Web Service (DWS), and the endpoints for approval processing in Documaker Interactive. The deployment process for ODEE will create 3 managed WebLogic servers for hosting various Documaker components (JMS, Interactive, DWS, Dashboard, Documaker Administrator, etcetera) and it will set the ports used for each of these services. In this screen you can change these values if you know how you want to deploy these managed servers - but for now we'll just accept the defaults. Click Next. Verify the installation details and click Install. You can save the installation into a response file if you need to (which might be useful if you want to rerun this installation in an unattended fashion). Allow the installation to progress... Click Next. You can save the response file if needed (e.g. in case you forgot to save it earlier!) Click Finish. That's it, you're done with the initial installation. Have a look around the ODEE_HOME that you just installed (remember we selected c:\oracle\odee_1?) and look at the files that are laid down. Don't change anything just yet! Stay tuned for the next segment where we complete and verify the installation. 

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• Azure Task Scheduling Options

  - by charlie.mott

  Currently, the Azure PaaS does not offer a distributed\resilient task scheduling service.  If you do want to host a task scheduling product\solution off-premise (and ideally use Azure), what are your options? PaaS Option 1: Worker Roles Use a worker role to schedule and execute actions at specific time periods.  There are a few frameworks available to assist with this: http://azuretoolkit.codeplex.com https://github.com/Lokad/lokad-cloud/wiki/TaskScheduler http://blog.smarx.com/posts/building-a-task-scheduler-in-windows-azure - This addresses a slightly different set of requirements. It’s a more dynamic approach for queuing up tasks, but not repeatable tasks (e.g. daily). I found the Azure Toolkit option the most simple to implement.  Step 1 : Create a domain entity implementing IJob for each job to schedule.  In this sample, I asynchronously call a WCF service method. 1: namespace Acme.WorkerRole.Jobs 2: { 3: using AzureToolkit; 4: using ScheduledTasksService; 5: 6: public class UploadEmployeesJob : IJob 7: { 8: public void Run() 9: { 10: // Call Tasks Service 11: var client = new ScheduledTasksServiceClient("BasicHttpBinding_IScheduledTasksService"); 12: client.UploadEmployees(); 13: client.Close(); 14: } 15: } 16: } Step 2 : In the worker role run method, add the jobs to the toolkit engine. 1: namespace Acme.WorkerRole 2: { 3: using AzureToolkit.Engine; 4: using Jobs; 5:   6: public class WorkerRole : WorkerRoleEntryPoint 7: { 8: public override void Run() 9: { 10: var engine = new CloudEngine(); 11:   12: // Add Scheduled Jobs (using CronJob syntax - see http://www.adminschoice.com/crontab-quick-reference). 13:   14: // 1. Upload Employee job - 8.00 PM every weekday (Mon-Fri) 15: engine.WithJobScheduler().ScheduleJob<UploadEmployeesJob>(c => { c.CronSchedule = "0 20 * * 1-5"; }); 16: // 2. Purge Data job - 10 AM every Saturday 17: engine.WithJobScheduler().ScheduleJob<PurgeDataJob>(c => { c.CronSchedule = "0 10 * * 6"; }); 18: // 3. Process Exceptions job - Every 5 minutes 19: engine.WithJobScheduler().ScheduleJob<ProcessExceptionsJob>(c => { c.CronSchedule = "*/5 * * * *"; }); 20:   21: engine.Run(); 22: base.Run(); 23: } 24: } 25: } Pros Cons Azure Toolkit option is simple to implement. For the AzureToolkit option, you are limited to a single worker role.  Otherwise, the jobs will be executed multiple times, once for each worker role instance.   Paying for a continuously running worker role, even if it just processes a single job once a week.  If you only have a few scheduled tasks to run calling asynchronous services hosted in different web roles, an extra small worker role likely to be sufficient.  However, for an extra small worker role this still costs $14.40/month (03/09/2012). Option 2: Use Scheduled Task on Azure Web Role calling a console app Setup a Windows Scheduled Task on the Azure Web Role. This calls a console application that calls the WCF service methods that run the task actions. This design is described here: http://www.ronaldwidha.net/2011/02/23/cron-job-on-azure-using-scheduled-task-on-a-web-role-to-replace-azure-worker-role-for-background-job/ http://www.voiceoftech.com/swhitley/index.php/2011/07/windows-azure-task-scheduler/ http://devlicio.us/blogs/vinull/archive/2011/10/23/moving-to-azure-worker-roles-for-nothing-and-tasks-for-free.aspx Pros Cons Fairly easy to implement. Supportability - I RDC’ed onto the Azure server and stopped the scheduled task. I then rebooted the machine and the task was re-started. I also tried deleting the task and rebooting, the same thing occurred. The only way to permanently guarantee that a task is disabled is to do a fresh deployment. I think this is a major supportability concern.   Saleability - multiple instances would trigger multiple tasks. You can only have one instance for the scheduled task web role. The guidance implements setup of the scheduled task as part of a web role instance. But if you have more than one instance in a web role, the task will be triggered multiple times for each scheduled action (once per machine). Workaround: If we wanted to use scheduled tasks for another client with a saleable WCF service, then we could include the console & tasks scripts in a separate web role (e.g. a empty WCF service with no real purpose to it). SaaS Option 3: Azure Marketplace I thought that someone might be offering this type of service via the Azure marketplace. At the point of writing this blog post, I did not find anyone doing so. https://datamarket.azure.com/ Pros Cons   Nobody currently offers this on the Azure Marketplace. Option 4: Online Job Scheduling Service Provider There are plenty of online providers that offer this type of service on a pay-as-you-go approach.  Some of these are free for small usage.   Many of these providers are listed here: http://en.wikipedia.org/wiki/Webcron Pros Cons No bespoke development for scheduler. Reliance on third party. IaaS Option 5: Setup Scheduling Software on Azure IaaS VM’s One of job scheduling software offerings could be installed and configured on Azure VM’s.  A list of software options is listed here: http://en.wikipedia.org/wiki/List_of_job_scheduler_software Pros Cons Enterprise distributed\resilient task scheduling service VM Setup and maintenance   Software Licence Costs Option 6: VM Gallery A the time of writing this blog post, I did not spot a VM in the gallery that included pre-installation of any of the above software options. Pros Cons   No current VM template. Summary For my current project that had a small handful of tasks to schedule with a limited project budget I chose option 1 (a worker role using the Azure Toolkit to schedule tasks).  If I was building an enterprise scale solution for the future, options 4 and 5 are currently worthy of consideration. Hopefully, Microsoft will include tasks scheduling in the future as part of their PaaS offerings.

  Read the article

• Why JSF Matters (to You)

  - by reza_rahman

        "Those who have knowledge, don’t predict. Those who predict, don’t have knowledge."                                                                                                    – Lao Tzu You may have noticed Thoughtworks recently crowned the likes AngularJS, etc imminent successors to server-side web frameworks. They apparently also deemed it necessary to single out JSF for righteous scorn. I have to say as I was reading the analysis I couldn't help but remember they also promptly jumped on the Ruby, Rails, Clojure, etc bandwagon a good few years ago seemingly similarly crowing these dynamic languages imminent successors to Java. I remember thinking then as I do now whether the folks at Thoughtworks are really that much smarter than me or if they are simply more prone to the Hipster buzz of the day. I'll let you make the final call on that one. I also noticed mention of "J2EE" in the context of JSF and had to wonder how up-to-date or knowledgeable the person writing the analysis actually was given that the term was basically retired almost a decade ago. There's one thing that I am absolutely sure about though - as a long time pretty happy user of JSF, I had no choice but to speak up on what I believe JSF offers. If you feel the same way, I would encourage you to support the team behind JSF whose hard work you may have benefited from over the years. True to his outspoken character PrimeFaces lead Cagatay Civici certainly did not mince words making the case for the JSF ecosystem - his excellent write-up is well worth a read. He specifically pointed out the practical problems in going whole hog with bare metal JavaScript, CSS, HTML for many development teams. I'll admit I had to smile when I read his closing sentence as well as the rather cheerful comments to the post from actual current JSF/PrimeFaces users that are apparently supposed to be on a gloomy death march. In a similar vein, OmniFaces developer Arjan Tijms did a great job pointing out the fact that despite the extremely competitive server-side Java Web UI space, JSF seems to manage to always consistently come out in either the number one or number two spot over many years and many data sources - do give his well-written message in the JAX-RS user forum a careful read. I don't think it's really reasonable to expect this to be the case for so many years if JSF was not at least a capable if not outstanding technology. If fact if you've ever wondered, Oracle itself is one of the largest JSF users on the planet. As Oracle's Shay Shmeltzer explains in a recent JSF Central interview, many of Oracle's strategic products such as ADF, ADF Mobile and Fusion Applications itself is built on JSF. There are well over 3,000 active developers working on these codebases. I don't think anyone can think of a more compelling reason to make sure that a technology is as effective as possible for practical development under real world conditions. Standing on the shoulders of the above giants, I feel like I can be pretty brief in making my own case for JSF: JSF is a powerful abstraction that brings the original Smalltalk MVC pattern to web development. This means cutting down boilerplate code to the bare minimum such that you really can think of just writing your view markup and then simply wire up some properties and event handlers on a POJO. The best way to see what this really means is to compare JSF code for a pretty small case to other approaches. You should then multiply the additional work for the typical enterprise project to try to understand what the productivity trade-offs are. This is reason alone for me to personally never take any other approach seriously as my primary web UI solution unless it can match the sheer productivity of JSF. Thanks to JSF's focus on components from the ground-up JSF has an extremely strong ecosystem that includes projects like PrimeFaces, RichFaces, OmniFaces, ICEFaces and of course ADF Faces/Mobile. These component libraries taken together constitute perhaps the largest widget set ever developed and optimized for a single web UI technology. To begin to grasp what this really means, just briefly browse the excellent PrimeFaces showcase and think about the fact that you can readily use the widgets on that showcase by just using some simple markup and knowing near to nothing about AJAX, JavaScript or CSS. JSF has the fair and legitimate advantage of being an open vendor neutral standard. This means that no single company, individual or insular clique controls JSF - openness, transparency, accountability, plurality, collaboration and inclusiveness is virtually guaranteed by the standards process itself. You have the option to choose between compatible implementations, escape any form of lock-in or even create your own compatible implementation! As you might gather from the quote at the top of the post, I am not a fan of crystal ball gazing and certainly don't want to engage in it myself. Who knows? However far-fetched it may seem maybe AngularJS is the only future we all have after all. If that is the case, so be it. Unlike what you might have been told, Java EE is about choice at heart and it can certainly work extremely well as a back-end for AngularJS. Likewise, you are also most certainly not limited to just JSF for working with Java EE - you have a rich set of choices like Struts 2, Vaadin, Errai, VRaptor 4, Wicket or perhaps even the new action-oriented web framework being considered for Java EE 8 based on the work in Jersey MVC... Please note that any views expressed here are my own only and certainly does not reflect the position of Oracle as a company.

  Read the article

• Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

  - by Eli

  Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

  Read the article

• Cablemodem (SBG6580) firewall denying some outbound traffic? Why? Not configured [migrated]

  - by lairdb

  I finally got around to turning the syslog on for my cablemodem (Motorola Surfboard SBG6580) and I'm seeing about the expected amount of inbound attackage being blocked... 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:56 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:56 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 17.172.232.109,5223 --> 66.27.xx.xx,53814 DENY:Firewall interface access request 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:57 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,443 --> 66.27.xx.xx,53385 DENY: Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:57 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:10 Local0.Alert 192.168.111.1 May 31 04:59:04 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,443 --> 66.27.xx.xx,59960 DENY: Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:10 Local0.Alert 192.168.111.1 May 31 04:59:04 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack ...and that's great. (Sad, but great.) But I'm also seeing a HUGE amount of what appears to be denied outbound connectivity: 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58969 --> 38.81.66.127,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58969 --> 38.81.66.127,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58965 --> 162.222.41.13,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58965 --> 162.222.41.13,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58964 --> 38.81.66.179,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58964 --> 38.81.66.179,443 DENY: Inbound or outbound access request ...and Spot checking suggests that it's all legitimate traffic (Opening connections to CrashPlan, etc.), I have no restrictions configured in the modem; I don't see why it should be blocking anything. Am I misreading the log entry, and it's not actually being denied? (Seems unlikely.) Is the ISP (TWC) pushing deny tables that are not exposed in the UI? (Tinfoil hat too tight.) I'm confused. (The good news, such as it is, is that AFAIK I'm not experiencing any actual issues... but maybe I am; tough to tell.) Thanks.

  Read the article

• Windows 7, file properties - Is "date accessed" ALWAYS 100% accurate?

  - by Robert

  Hello, Here's the situation: I went on vacation for a couple of weeks, but before I left, I took the harddrive out of my computer and hid it in a different location. Upon coming back on Monday and putting the harddrive back in my computer, I right-clicked on different files to see their properties. Interestingly enough, several files had been accessed during the time I was gone! I right-clicked different files in various locations on the harddrive, and all of these suspect files had been accessed within a certain time range (Sunday, ?January ?09, ?2011, approximately ??between 6:52:16 PM - 7:16:25 PM). Some of them had been accessed at the exact same time--down to the very second. This makes me think that someone must have done a search on my harddrive for certain types of files and then copied all those files to some other medium. The Windows 7 installation on this harddrive is password protected, but NOT encrypted, so they could have easily put the harddrive into an enclosure/toaster to access it from a different computer. Of course I did not right-click every single file on my computer, but did so in different folders. For instance, one of the folders I went through has different types of files: .mp3, ,prproj, .3gp, .mpg, .wmv, .xmp, .txt with file-sizes ranging from 2 KB to 29.7 MB (there is also a sub-folder in this folder which contains only .jpg files); however, of all these different types of files in this folder and its subfolder, all of them had been accessed (including the .jpg files from the sub-folder) EXCEPT the .mp3 files (if it makes any difference, the .mp3 files in this folder range in size from 187 KB to 4881 KB). Additionally, this sub-folder which contained only .jpg files (48 .jpg files to be exact) was not accessed during this time--only the .jpg files within it were accessed-- (between 6:57:03 PM - 6:57:08 PM). I thought that perhaps this was some kind of Windows glitch that was displaying the wrong access date, but then I looked at the "date created" and "date modified" for all of these files in question, and their created/modified dates and times were spot on correct. My first thought was that someone put the harddrive into an enclosure/toaster and viewed the files; but then I realized that this was impossible because several of the files had been accessed at the same exact time down to the second. So this made me think that the only other way the "date accessed" could have changed would have been if someone copied the files. Is there any chance at all whatsoever that this is some kind of Windows glitch or something, or is it a fact that someone was indeed accessing my files (and if someone was accessing my files, am I right about the files in question having been copied)? Is there any other possibility for what could have happened? Do I need to use any kinds of forensics tools to further investigate this matter (and if so, which tools), or is there any other way in which I can be certain of what took place in that timeframe the day before I got back? Or is what I see with Windows 7 good enough (i.e. accurate and truthful)? Thanks in advance, and please let me know if any other details are required on my part.

  Read the article

• "power limit notification" clobbering on 12G Dell servers with RHEL6

  - by Andrew B

  Server: Poweredge r620 OS: RHEL 6.4 Kernel: 2.6.32-358.18.1.el6.x86_64 I'm experiencing application alarms in my production environment. Critical CPU hungry processes are being starved of resources and causing a processing backlog. The problem is happening on all the 12th Generation Dell servers (r620s) in a recently deployed cluster. As near as I can tell, instances of this happening are matching up to peak CPU utilization, accompanied by massive amounts of "power limit notification" spam in dmesg. An excerpt of one of these events: Nov 7 10:15:15 someserver [.crit] CPU12: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU6: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU14: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU0: Package power limit notification (total events = 11) Nov 7 10:15:15 someserver [.crit] CPU6: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU14: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU18: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU20: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU2: Package power limit notification (total events = 12) Nov 7 10:15:15 someserver [.crit] CPU10: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Core power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU4: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU16: Package power limit notification (total events = 13) Nov 7 10:15:15 someserver [.crit] CPU20: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU8: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU10: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU22: Package power limit notification (total events = 14) Nov 7 10:15:15 someserver [.crit] CPU15: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU3: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU1: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU5: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU15: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU3: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU1: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU5: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU19: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU17: Package power limit notification (total events = 377) Nov 7 10:15:15 someserver [.crit] CPU9: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU21: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU23: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU11: Core power limit notification (total events = 369) Nov 7 10:15:15 someserver [.crit] CPU13: Package power limit notification (total events = 376) Nov 7 10:15:15 someserver [.crit] CPU7: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU19: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU9: Package power limit notification (total events = 374) Nov 7 10:15:15 someserver [.crit] CPU21: Package power limit notification (total events = 375) Nov 7 10:15:15 someserver [.crit] CPU23: Package power limit notification (total events = 374) A little Google Fu reveals that this is typically associated with the CPU running hot, or voltage regulation kicking in. I don't think that's what is happening though. Temperature sensors for all servers in the cluster are running fine, Power Cap Policy is disabled in the iDRAC, and my System Profile is set to "Performance" on all of these servers: # omreport chassis biossetup | grep -A10 'System Profile' System Profile Settings ------------------------------------------ System Profile : Performance CPU Power Management : Maximum Performance Memory Frequency : Maximum Performance Turbo Boost : Enabled C1E : Disabled C States : Disabled Monitor/Mwait : Enabled Memory Patrol Scrub : Standard Memory Refresh Rate : 1x Memory Operating Voltage : Auto Collaborative CPU Performance Control : Disabled A Dell mailing list post describes the symptoms almost perfectly. Dell suggested that the author try using the Performance profile, but that didn't help. He ended up applying some settings in Dell's guide for configuring a server for low latency environments and one of those settings (or a combination thereof) seems to have fixed the problem. Kernel.org bug #36182 notes that power-limit interrupt debugging was enabled by default, which is causing performance degradation in scenarios where CPU voltage regulation is kicking in. A RHN KB article (RHN login required) mentions a problem impacting PE r620 and r720 servers not running the Performance profile, and recommends an update to a kernel released two weeks ago. ...Except we are running the Performance profile... Everything I can find online is running me in circles here. What's the heck is going on?

  Read the article

• FFmpeg audio dont work in converted videos

  - by Juddy Swaft

  NOTICE: when i convert videos via terminal and download them from ftp into pc the audio works fine. I use: if($ext == "avi" && $convert_avi == true) { $convert_source = _VIDEOS_DIR_PATH.$new_name; $conv_name = substr(md5($file['name'].rand(1,888)), 2, 10).".mp4"; $converted_file = _VIDEOS_DIR_PATH.$conv_name; $ffmpeg_command = 'ffmpeg -i '.$convert_source.' -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 '.$converted_file; echo exec($ffmpeg_command); $sql = "UPDATE pm_temp SET url = '".$conv_name."' WHERE url = '".$new_name."' LIMIT 1"; $result = @mysql_query($sql); unlink($convert_source); } This code to convert avi to mp4 ffmpeg concole output: root@1tb:~# ffmpeg -i sample.avi -acodec libmp3lame -vcodec libx264 -s 1280x720 -ar 44100 -async 44100 -r 29.970 -ac 2 -qscale 5 goodsample.mp4 ffmpeg version 0.7.15, Copyright (c) 2000-2013 the FFmpeg developers built on Feb 22 2013 07:18:58 with gcc 4.4.5 configuration: --enable-libdc1394 --prefix=/usr --extra-cflags='-Wall -g ' --cc='ccache cc' --enable-shared --enable-libmp3lame --enable-gpl --enable-libvorbis --enable-pthreads --enable-libfaac --enable-libxvid --enable-postproc --enable-x11grab --enable-libgsm --enable-libtheora --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libx264 --enable-libspeex --enable-nonfree --disable-stripping --enable-avfilter --enable-libdirac --disable-decoder=libdirac --enable-libfreetype --enable-libschroedinger --disable-encoder=libschroedinger - s libavutil 50. 43. 0 / 50. 43. 0 libavcodec 52.123. 0 / 52.123. 0 libavformat 52.111. 0 / 52.111. 0 libavdevice 52. 5. 0 / 52. 5. 0 libavfilter 1. 80. 0 / 1. 80. 0 libswscale 0. 14. 1 / 0. 14. 1 libpostproc 51. 2. 0 / 51. 2. 0 [mp3 @ 0x191d4100] Header missing [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'sample.avi': Metadata: encoder : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:01:01.81, start: 0.000000, bitrate: 1194 kb/s Stream #0.0: Video: mpeg4, yuv420p, 640x352 [PAR 1:1 DAR 20:11], 23.98 tbr, Stream #0.1: Audio: mp3, 48000 Hz, stereo, s16, 128 kb/s [buffer @ 0x191d1c80] w:640 h:352 pixfmt:yuv420p tb:1/1000000 sar:1/1 sws_param: [scale @ 0x191d6880] w:640 h:352 fmt:yuv420p -> w:1280 h:720 fmt:yuv420p flags:0 [libx264 @ 0x191ce5a0] Default settings detected, using medium profile [libx264 @ 0x191ce5a0] using SAR=45/44 [libx264 @ 0x191ce5a0] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle S [libx264 @ 0x191ce5a0] profile High, level 3.1 [libx264 @ 0x191ce5a0] 264 - core 118 - H.264/MPEG-4 AVC codec - Copyleft 2003-2 6 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_off 1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_l Output #0, mp4, to 'goodsample.mp4': Metadata: encoder : Lavf52.111.0 Stream #0.0: Video: libx264, yuv420p, 1280x720 [PAR 45:44 DAR 20:11], q=2-31 Stream #0.1: Audio: libmp3lame, 44100 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop, [?] for help [mp3 @ 0x191d4100] Header missing Error while decoding stream #0.1 [mpeg4 @ 0x191d1dc0] Invalid and inefficient vfw-avi packed B frames detected [mp3 @ 0x191d4100] incomplete frame 9467kB time=00:01:00.32 bitrate=1285.5kbits/ Error while decoding stream #0.1 frame= 1852 fps= 20 q=29.0 Lsize= 9652kB time=00:01:01.72 bitrate=1280.9kbits video:9121kB audio:483kB global headers:0kB muxing overhead 0.499688% frame I:11 Avg QP:16.78 size: 51456 [libx264 @ 0x191ce5a0] frame P:784 Avg QP:20.81 size: 8954 [libx264 @ 0x191ce5a0] frame B:1057 Avg QP:26.06 size: 1659 [libx264 @ 0x191ce5a0] consecutive B-frames: 22.0% 3.1% 7.5% 67.4% [libx264 @ 0x191ce5a0] mb I I16..4: 31.1% 59.8% 9.1% [libx264 @ 0x191ce5a0] mb P I16..4: 1.8% 2.6% 0.2% P16..4: 24.3% 7.0% 4.0 [libx264 @ 0x191ce5a0] mb B I16..4: 0.1% 0.1% 0.0% B16..8: 22.7% 0.8% 0.2 [libx264 @ 0x191ce5a0] 8x8 transform intra:57.0% inter:72.6% [libx264 @ 0x191ce5a0] coded y,uvDC,uvAC intra: 44.4% 33.3% 10.3% inter: 7.6% 5. [libx264 @ 0x191ce5a0] i16 v,h,dc,p: 68% 14% 8% 10% [libx264 @ 0x191ce5a0] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 21% 14% 27% 5% 7% 7% 6 [libx264 @ 0x191ce5a0] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 28% 14% 14% 6% 10% 9% 7 [libx264 @ 0x191ce5a0] i8c dc,h,v,p: 67% 13% 17% 3% [libx264 @ 0x191ce5a0] Weighted P-Frames: Y:1.9% UV:0.4% [libx264 @ 0x191ce5a0] ref P L0: 62.2% 12.8% 10.3% 14.5% 0.2% [libx264 @ 0x191ce5a0] ref B L0: 88.1% 5.5% 6.4% [libx264 @ 0x191ce5a0] ref B L1: 95.7% 4.3% [libx264 @ 0x191ce5a0] kb/s:1209.03 I know there is couple errors tough, but i dont know hot to fix it. Also i would be very thankfull if someone can help reduce video size but is not main problem video weights as original avi but sill.

  Read the article

• RAID1 rebuild fails due to disk errors

  - by overlord_tm

  Quick info: Dell R410 with 2x500GB drives in RAID1 on H700 Adapter Recently one of drives in RAID1 array on server failed, lets call it Drive 0. RAID controller marked it as fault and put it offline. I replaced faulty disk with new one (same series and manufacturer, just bigger) and configured new disk as hot spare. Rebuild from Drive1 started immediately and after 1.5 hour I got message that Drive 1 failed. Server was unresponsive (kernel panic) and required reboot. Given that half hour before this error rebuild was at about 40%, I estimated that new drive is not in sync yet and tried to reboot just with Drive 1. RAID controller complained a bit about missing RAID arrays, but it found foreign RAID array on Drive 1 and I imported it. Server booted and it runs (from degraded RAID). Here is SMART data for disks. Drive 0 (the one that failed first) ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 142 142 021 - 3866 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10432 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 112 106 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 198 000 - 3 And Drive 1 (the drive which was reported healthy from controller until rebuild was attempted) ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 35 3 Spin_Up_Time POS--K 143 143 021 - 3841 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10455 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 114 105 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 3 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 In extended error logs from SMART I found: Drive 0 has only one error Error 1 [0] occurred at disk power-on lifetime: 10282 hours (428 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 18 00 00 00 6a 24 20 40 00 Error: IDNF at LBA = 0x006a2420 = 6956064 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 60 00 f8 00 00 00 6a 24 20 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 18 00 60 00 00 00 6a 24 00 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 80 00 58 00 00 00 6a 23 80 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 68 00 50 00 00 00 6a 23 18 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 10 00 10 00 00 00 6a 23 00 40 00 17d+20:25:18.104 WRITE FPDMA QUEUED But Drive 1 has 883 errors. I see only few last ones and all errors I can see look like this: Error 883 [18] occurred at disk power-on lifetime: 10454 hours (435 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 80 00 00 39 97 19 c2 40 00 Error: AMNF at LBA = 0x399719c2 = 966203842 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:57.802 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 1d+00:25:57.779 READ LOG EXT 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:55.704 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 1d+00:25:55.681 READ LOG EXT 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:53.606 READ FPDMA QUEUED Given those errors, is there any way I can rebuild RAID back, or should I make backup, shutdown server, replace disks with new ones and restore it? What about if I dd faulty disk to new one from linux running on USB/CD? Also, if anyone have more experiences, what could be causes for those errors? Crappy controller or disks? Disks are about 1 year old, but it is pretty unbelievable to me that both would die within so short timespan.

  Read the article

• Creating Persistent Drive Labels With UDEV Using /dev/disk/by-path

  - by Matt

  I have a new BackBlaze Pod (BackBlaze Pod 2.0). It has 45 3TB drives and they when I first set it up they were labeled /dev/sda through /dev/sdz and /dev/sdaa through /dev/sdas. I used mdadm to setup three really big 15 drive RAID6 arrays. However, since first setup a few weeks ago I had a couple of the hard drives fail on me. I've replaced them but now the arrays are complaining because they can't find the missing drives. When I list the the disks... ls -l /dev/sd* I see that /dev/sda /dev/sdf /dev/sdk /dev/sdp no longer appear and now there are 4 new ones... /dev/sdau /dev/sdav /dev/sdaw /dev/sdax I also just found that I can do this... ls -l /dev/disk/by-path/ total 0 lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:02:04.0-scsi-0:0:0:0 -> ../../sdau lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:1:0:0 -> ../../sdb lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:2:0:0 -> ../../sdc lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:3:0:0 -> ../../sdd lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:4:0:0 -> ../../sde lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:02:04.0-scsi-2:0:0:0 -> ../../sdae lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:1:0:0 -> ../../sdg lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:2:0:0 -> ../../sdh lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:3:0:0 -> ../../sdi lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:4:0:0 -> ../../sdj lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:02:04.0-scsi-3:0:0:0 -> ../../sdav lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:1:0:0 -> ../../sdl lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:2:0:0 -> ../../sdm lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:3:0:0 -> ../../sdn lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:4:0:0 -> ../../sdo lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:04:04.0-scsi-0:0:0:0 -> ../../sdax lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:1:0:0 -> ../../sdq lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:2:0:0 -> ../../sdr lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:3:0:0 -> ../../sds lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:4:0:0 -> ../../sdt lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:0:0:0 -> ../../sdu lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:1:0:0 -> ../../sdv lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:2:0:0 -> ../../sdw lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:3:0:0 -> ../../sdx lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:4:0:0 -> ../../sdy lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-3:0:0:0 -> ../../sdz I didn't list them all....you can see the problem above. They're sorted by scsi id here but sda is missing...replaced by sdau...etc... So obviously the arrays are complaining. Is it possible to get Linux to reread the drive labels in the correct order or am I screwed? My initial design with 15 drive arrays is not ideal. With 3TB drives the rebuild times were taking 3 or 4 days....maybe more. I'm scrapping the whole design and I think I am going to go with 6 x 7 RAID5 disk arrays and 3 hot spares to make the arrays a bit easier to manage and shorten the rebuild times. But I'd like to clean up the drive labels so they aren't out of order. I haven't figured out how to do this yet. Does anyone know how to get this straightened out? Thanks, Matt

  Read the article

• Mount TMPFS instead of ro /dev

  - by schiggn

  I am working on a ARM-Based embedded system with a custom Debian Linux based on kernel 2.6.31. In the final system, the Root file system is stored as squashfs on flash. Now, the folder /dev is created by udev, but since there is no hot plugging functionality needed and booting time is critical, I wanted to delete udev and "hard code" the /dev folder (read here, page 5). because i still need to change parameters of the devices (with ioctl /sysfs) this does not work for me in this case. so i thought of mounting a tmpfs on /dev and change the parameters there. is this possible? and how to do best? my approach would be: delete /dev from RFS create tar containing basic devices mount tmpfs /dev untar tar-file into /dev change parameters Could this work? Do you see any problems? I found out, that you can mount on top of already mounted mount point, is it somehow possible just to take data with while mounting the new file system? if so that would be very convenient! Thanks Update: I just tried that out, but I'm stuck at a certain point. I packed all my devices into devices.tar, packed it into /usr of my squashfs and added the following lines to mountkernfs.sh, which is executed right after INIT. #mount /dev on tmpfs echo -n "Mounting /dev on tmpfs..." mount -o size=5M,mode=0755 -t tmpfs tmpfs /dev mknod -m 600 /dev/console c 5 1 mknod -m 600 /dev/null c 1 3 echo "done." echo -n "Populating /dev..." tar -xf /usr/devices.tar -C /dev echo "done." This works fine on the version over NFS, if I place printf's in the code, I can see it executing, if I comment out the extracting part, its complaining about missing devices. Booting OK mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. System Clock set to: Thu Sep 13 11:26:23 UTC 2012. INIT: Entering runlevel: 2 UBI: attaching mtd8 to ubi0 Commenting out the extraction of the tar mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 IP-Config: Unable to set interface netmask (-22). Looking up port of RPC 100003/2 on 192.168.1.234 Looking up port of RPC 100005/1 on 192.168.1.234 VFS: Mounted root (nfs filesystem) on device 0:14. Freeing init memory: 136K INIT: version 2.86 booting Mounting /dev on tmpfs...done. Populating /dev...done. Initializing /var...done. Setting the system clock. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Unable to set System Clock to: Thu Sep 13 12:24:00 UTC 2012 ... (warning). INIT: Entering runlevel: 2 libubi: error!: cannot open "/dev/ubi_ctrl" So far so good. But if I pack the whole story into a squashfs and boot from there, it is acting strange. It's telling me while booting that it is unable to open an initial console and its throwing errors on mounting the UBIFS devices, but finally provides a login anyway. Over that my echo's are not executed. If I then log in, /dev is mounted as TMPFS as desired and all the devices reside inside. When I redo the "mount" command to mount the UBIFS partitions it is executed whitout problem and useable. From squashfs VFS: Mounted root (squashfs filesystem) readonly on device 31:15. Freeing init memory: 136K Warning: unable to open an initial console. mmc0: new high speed SDHC card at address 0007 mmcblk0: mmc0:0007 SD04G 3.67 GiB mmcblk0: p1 UBIFS error (pid 484): ubifs_get_sb: cannot open "ubi1_0", error -19 Additionally, a part of the rest of the bootscripts is still exexuted, but not all of them. Does anyone has a clue why? Other question, is 5MB enough/too much for /dev?

  Read the article

• Cisco PIX 515 doesn't seem to be passing traffic through according to static route

  - by Liquidkristal

  Ok, so I am having a spot of bother with a Cisco PIX515, I have posted the current running config below, now I am no cisco expert by any means although I can do basic stuff with them, now I am having trouble with traffic sent from the outside to address: 10.75.32.25 it just doesn't appear to be going anywhere. Now this firewall is deep inside a private network, with an upstream firewall that we don't manage. I have spoken to the people that look after that firewall and they say they they have traffic routing to 10.75.32.21 and 10.75.32.25 and thats it (although there is a website that runs from the server 172.16.102.5 which (if my understanding is correct) gets traffic via 10.75.32.23. Any ideas would be greatly appreciated as to me it should all just work, but its not (obviously if the config is all correct then there could be a problem with the web server that we are trying to access on 10.75.32.25, although the users say that they can get to it internally (172.16.102.8) which is even more confusing) PIX Version 6.3(3) interface ethernet0 auto interface ethernet1 auto interface ethernet2 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 academic security50 fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names name 195.157.180.168 outsideNET name 195.157.180.170 globalNAT name 195.157.180.174 gateway name 195.157.180.173 Mail-Global name 172.30.31.240 Mail-Local name 10.75.32.20 outsideIF name 82.219.210.17 frogman1 name 212.69.230.79 frogman2 name 78.105.118.9 frogman3 name 172.16.0.0 acadNET name 172.16.100.254 acadIF access-list acl_outside permit icmp any any echo-reply access-list acl_outside permit icmp any any unreachable access-list acl_outside permit icmp any any time-exceeded access-list acl_outside permit tcp any host 10.75.32.22 eq smtp access-list acl_outside permit tcp any host 10.75.32.22 eq 8383 access-list acl_outside permit tcp any host 10.75.32.22 eq 8385 access-list acl_outside permit tcp any host 10.75.32.22 eq 8484 access-list acl_outside permit tcp any host 10.75.32.22 eq 8485 access-list acl_outside permit ip any host 10.75.32.30 access-list acl_outside permit tcp any host 10.75.32.25 eq https access-list acl_outside permit tcp any host 10.75.32.25 eq www access-list acl_outside permit tcp any host 10.75.32.23 eq www access-list acl_outside permit tcp any host 10.75.32.23 eq https access-list acl_outside permit tcp host frogman1 host 10.75.32.23 eq ssh access-list acl_outside permit tcp host frogman2 host 10.75.32.23 eq ssh access-list acl_outside permit tcp host frogman3 host 10.75.32.23 eq ssh access-list acl_outside permit tcp any host 10.75.32.23 eq 2001 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp any host 10.75.32.23 eq smtp access-list acl_outside permit tcp any host 10.75.32.23 eq ssh access-list acl_outside permit tcp any host 10.75.32.24 eq ssh access-list acl_acad permit icmp any any echo-reply access-list acl_acad permit icmp any any unreachable access-list acl_acad permit icmp any any time-exceeded access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq www access-list acl_acad deny tcp any any eq www access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq https access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq 8080 access-list acl_acad permit tcp host 172.16.102.5 host 10.64.1.115 eq smtp pager lines 24 logging console debugging mtu outside 1500 mtu inside 1500 mtu academic 1500 ip address outside outsideIF 255.255.252.0 no ip address inside ip address academic acadIF 255.255.0.0 ip audit info action alarm ip audit attack action alarm pdm history enable arp timeout 14400 global (outside) 1 10.75.32.21 nat (academic) 1 acadNET 255.255.0.0 0 0 static (academic,outside) 10.75.32.22 Mail-Local netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.30 172.30.30.36 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.23 172.16.102.5 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.24 172.16.102.6 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.25 172.16.102.8 netmask 255.255.255.255 0 0 access-group acl_outside in interface outside access-group acl_acad in interface academic route outside 0.0.0.0 0.0.0.0 10.75.32.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius aaa-server LOCAL protocol local snmp-server host outside 172.31.10.153 snmp-server host outside 172.31.10.154 snmp-server host outside 172.31.10.155 no snmp-server location no snmp-server contact snmp-server community CPQ_HHS no snmp-server enable traps floodguard enable telnet 172.30.31.0 255.255.255.0 academic telnet timeout 5 ssh timeout 5 console timeout 0 terminal width 120 Cryptochecksum:hi2u : end PIX515#

  Read the article

• Windows 7: Search indexing is stuck

  - by Ricket

  When I open Indexing Options, it says: 4,317 items indexed Indexing in progress. Search results might not be complete during this time. It's stuck at 4,317 though; no more items have been indexed. Worst of all, SearchIndexer.exe is taking up 100% CPU (well, 50%, but I have a dual core CPU; it's taking up all processing power it can). It is not causing hard drive activity though. I tried clicking "Troubleshoot search and indexing" at the bottom of the Indexing Options window, but it couldn't find any problem. I've also tried the repair registry key that several websites suggest; I change HKLM\SOFTWARE\Microsoft\Windows Search SetupCompletedSuccessfully to 0 and restarted the computer, and it apparently repaired because it flipped back to 1, but the same problem continues to occur. It's reducing the battery life of my laptop and making it really hot so that my fans are running all the time. I've had to disable the Windows Search service. How can I fix this? Do I need to just flat-out reformat my computer? Update: I've tried rebuilding a couple times. There's nothing unusual about the locations I have to index, and I don't have any downloads in progress or anything like that. I don't see any reason why it stopped, and I noticed it much too late to do a system restore. At this point, I'm hoping someone will offer up some secret answer that will fix the problem, thus the bounty. Another update: I tried starting the service again, just to let it try yet again. It seemed okay at first (Indexing Options showed it operating at reduced speed due to user activity, and the number of files was going up). A while later I checked, and the service had stopped. Event viewer revealed some errors like this: Log Name: Application Source: Application Error Date: 2/1/2010 7:34:23 PM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ricky-win7 Description: Faulting application name: SearchIndexer.exe, version: 7.0.7600.16385, time stamp: 0x4a5bcdd0 Faulting module name: NLSData0007.dll, version: 6.1.7600.16385, time stamp: 0x4a5bda88 Exception code: 0xc0000005 Fault offset: 0x002141ba Faulting process id: 0x13a0 Faulting application start time: 0x01caa39f2a70ec02 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\System32\NLSData0007.dll Report Id: b4f7a7ae-0f92-11df-87fc-e5d65d8794c2 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2010-02-02T00:34:23.000000000Z" /> <EventRecordID>10689</EventRecordID> <Channel>Application</Channel> <Computer>ricky-win7</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7600.16385</Data> <Data>4a5bcdd0</Data> <Data>NLSData0007.dll</Data> <Data>6.1.7600.16385</Data> <Data>4a5bda88</Data> <Data>c0000005</Data> <Data>002141ba</Data> <Data>13a0</Data> <Data>01caa39f2a70ec02</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\System32\NLSData0007.dll</Data> <Data>b4f7a7ae-0f92-11df-87fc-e5d65d8794c2</Data> </EventData> </Event> If you are having the same error and arrived here from a Google search, please comment or add an answer detailing your progress on this, if any...

  Read the article

• System Center 2012 Service Manager change request status stuck at new

  - by Chuck Herrington

  The guy that built and setup this system left rather abruptly and I've taken over. My current issues are I have several change requests that are stuck at New. They do not move to Pending or In Progress. The system is not sending emails when incidents are getting assigned to people. This used to work on this system. I have done a lot of searching and the usual solution to this of stopping and restarting the system center services does not help. Can anyone give me any ideas of where else to look? Update: From all the searching I have done it seemed like I was at the point of re-installing. My initial installation of SCSM 2012 was on a machine that was upgraded from SCSM 2010 and also hosted SCCM 2007 and WSUS. We decided to give it a fresh start on a new server by installing a second instance of the SCSM server on a brand new 2008 R2 server then promoting the new server to the workflow master using the procedures outlined in this article - Dealing with Multiple management Servers. I've gotten to the point where we have both the old and the new server up and the new server has been promoted. I had hopped to get spammed by emails all the sudden due to the workflow taking off, but no such luck. Once all the clients are reconfigured to point to the new server we still plan to decommission the old server but at this point it seems to be that the problem is in the database. Short of any other input from the community, my next plan is to install a 180 day trial on a test server, complete with a separate database so that I can do a side by side comparison between a completely fresh install and what I have now and see if I can find any differences. While that install is running I also plan on investigating the event logs to see if there is anything in there that can shed some light on what is happening on the new server. Update 2: So I've now got a test SCSM server up with a completely fresh install including Database and it seems to be able to transition Change Requests from New to In Progress. I'm attempting to find differences between the two. Stay Tuned! Update 3: In looking through the event log on the new SCSM machine i discovered: Log Name: Operations Manager Source: OpsMgr Root Connector Date: 10/9/2013 3:48:18 PM Event ID: 28000 Task Category: None Level: Warning Keywords: Classic User: N/A Computer: scsm02 Description: The Root connector received an exception from the SDK Service while submitting task status: Cannot set availability on a health service that doesn't exist. This lead me to Event ID 2800 logged after installing secondary server for System Center 2012 Service Manager SP1. I contacted MS to obtain the hotfix, BIG warning here, turns out the hotfix is not so "hot". In order to apply this hotfix, you have to uninstall then reinstall using the files they supply. :( This is where I am at now ... Update 4: Not much luck after the re-install. The errors in the event log have gone away on the new server but the workflows still aren't running and neither the event log nor the workflow status screen seem to indicate why. I've done a comparison of the Activity and the Change Request Event Workflows and I've removed everything from the production system that is not in my fresh test system (which is everything), shut down the services, cleared out the cache folders and restarted the services and still no joy. At the moment the only thing I can think to do is either a)nuke the entire system including the database and start over, losing all of our data in the process or b)contact MS (which is probably going to cost us a butt load of money and time in the end to only advise us to do the same thing. Maybe more idea's will come after coffee ... No answers came after coffee. Attempting to contact MS. Managed to get to their first line of defense, gave them our SA number and someone is supposed to call me back. I am trying to log into my incident on their site to update my ticket with the link to this thread but when i click on the link in the email they sent me it goes to a "Sorry, the page you requested is not available" page ... Linux is looking better and better all the time.

  Read the article

• Upgrading from TFS 2010 RC to TFS 2010 RTM done

  - by Martin Hinshelwood

  Today is the big day, with the Launch of Visual Studio 2010 already done in Asia, and rolling around the world towards us, we are getting ready for the RTM (Released). We have had TFS 2010 in Production for nearly 6 months and have had only minimal problems. Update 12th April 2010  – Added Scott Hanselman’s tweet about the MSDN download release time. SSW was the first company in the world outside of Microsoft to deploy Visual Studio 2010 Team Foundation Server to production, not once, but twice. I am hoping to make it 3 in a row, but with all the hype around the new version, and with it being a production release and not just a go-live, I think there will be a lot of competition. Developers: MSDN will be updated with #vs2010 downloads and details at 10am PST *today*! @shanselman - Scott Hanselman Same as before, we need to Uninstall 2010 RC and install 2010 RTM. The installer will take care of all the complexity of actually upgrading any schema changes. If you are upgrading from TFS 2008 to TFS2010 you can follow our Rules To Better TFS 2010 Migration and read my post on our successes.   We run TFS 2010 in a Hyper-V virtual environment, so we have the advantage of running a snapshot as well as taking a DB backup. Done - Snapshot the hyper-v server Microsoft does not support taking a snapshot of a running server, for very good reason, and Brian Harry wrote a post after my last upgrade with the reason why you should never snapshot a running server. Done - Uninstall Visual Studio Team Explorer 2010 RC You will need to uninstall all of the Visual Studio 2010 RC client bits that you have on the server. Done - Uninstall TFS 2010 RC Done - Install TFS 2010 RTM Done - Configure TFS 2010 RTM Pick the Upgrade option and point it at your existing “tfs_Configuration” database to load all of the existing settings Done - Upgrade the SharePoint Extensions Upgrade Build Servers (Pending) Test the server The back out plan, and you should always have one, is to restore the snapshot. Upgrading to Team Foundation Server 2010 – Done The first thing you need to do is off the TFS server and then log into the Hyper-v server and create a snapshot. Figure: Make sure you turn the server off and delete all old snapshots before you take a new one I noticed that the snapshot that was taken before the Beta 2 to RC upgrade was still there. You should really delete old snapshots before you create a new one, but in this case the SysAdmin (who is currently tucked up in bed) asked me not to. I guess he is worried about a developer messing up his server Turn your server on and wait for it to boot in anticipation of all the nice shiny RTM’ness that is coming next. The upgrade procedure for TFS2010 is to uninstal the old version and install the new one. Figure: Remove Visual Studio 2010 Team Foundation Server RC from the system.   Figure: Most of the heavy lifting is done by the Uninstaller, but make sure you have removed any of the client bits first. Specifically Visual Studio 2010 or Team Explorer 2010.  Once the uninstall is complete, this took around 5 minutes for me, you can begin the install of the RTM. Running the 64 bit OS will allow the application to use more than 2GB RAM, which while not common may be of use in heavy load situations. Figure: It is always recommended to install the 64bit version of a server application where possible. I do not think it is likely, with SharePoint 2010 and Exchange 2010  and even Windows Server 2008 R2 being 64 bit only, I do not think there will be another release of a server app that is 32bit. You then need to choose what it is you want to install. This depends on how you are running TFS and on how many servers. In our case we run TFS and the Team Foundation Build Service (controller only) on out TFS server along with Analysis services and Reporting Services. But our SharePoint server lives elsewhere. Figure: This always confuses people, but in reality it makes sense. Don’t install what you do not need. Every extra you install has an impact of performance. If you are integrating with SharePoint you will need to run this install on every Front end server in your farm and don’t forget to upgrade your Build servers and proxy servers later. Figure: Selecting only Team Foundation Server (TFS) and Team Foundation Build Services (TFBS)   It is worth noting that if you have a lot of builds kicking off, and hence a lot of get operations against your TFS server, you can use a proxy server to cache the source control on another server in between your TFS server and your build servers. Figure: Installing Microsoft .NET Framework 4 takes the most time. Figure: Now run Windows Update, and SSW Diagnostic to make sure all your bits and bobs are up to date. Note: SSW Diagnostic will check your Power Tools, Add-on’s, Check in Policies and other bits as well. Configure Team Foundation Server 2010 – Done Now you can configure the server. If you have no key you will need to pick “Install a Trial Licence”, but it is only £500, or free with a MSDN subscription. Anyway, if you pick Trial you get 90 days to get your key. Figure: You can pick trial and add your key later using the TFS Server Admin. Here is where the real choices happen. We are doing an Upgrade from a previous version, so I will pick Upgrade the same as all you folks that are using the RC or TFS 2008. Figure: The upgrade wizard takes your existing 2010 or 2008 databases and upgraded them to the release.   Once you have entered your database server name you can click “List available databases” and it will show what it can upgrade. Figure: Select your database from the list and at this point, make sure you have a valid backup. At this point you have not made ANY changes to the databases. At this point the configuration wizard will load configuration from your existing database if you have one. If you are upgrading TFS 2008 refer to Rules To Better TFS 2010 Migration. Mostly during the wizard the default values will suffice, but depending on the configuration you want you can pick different options. Figure: Set the application tier account and Authentication method to use. We use NTLM to keep things simple as we host our TFS server externally for our remote developers.  Figure: Setting your TFS server URL’s to be the remote URL’s allows the reports to be accessed without using VPN. Very handy for those remote developers. Figure: Detected the existing Warehouse no problem. Figure: Again we love green ticks. It gives us a warm fuzzy feeling. Figure: The username for connecting to Reporting services should be a domain account (if you are on a domain that is). Figure: Setup the SharePoint integration to connect to your external SharePoint server. You can take the option to connect later.   You then need to run all of your readiness checks. These check can save your life! it will check all of the settings that you have entered as well as checking all the external services are configures and running properly. There are two reasons that TFS 2010 is so easy and painless to install where previous version were not. Microsoft changes the install to two steps, Install and configuration. The second reason is that they have pulled out all of the stops in making the install run all the checks necessary to make sure that once you start the install that it will complete. if you find any errors I recommend that you report them on http://connect.microsoft.com so everyone can benefit from your misery.   Figure: Now we have everything setup the configuration wizard can do its work.  Figure: Took a while on the “Web site” stage for some point, but zipped though after that.  Figure: last wee bit. TFS Needs to do a little tinkering with the data to complete the upgrade. Figure: All upgraded. I am not worried about the yellow triangle as SharePoint was being a little silly Exception Message: TF254021: The account name or password that you specified is not valid. (type TfsAdminException) Exception Stack Trace:    at Microsoft.TeamFoundation.Management.Controls.WizardCommon.AccountSelectionControl.TestLogon(String connectionString)    at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument) [Info   @16:10:16.307] Benign exception caught as part of verify: Exception Message: TF255329: The following site could not be accessed: http://projects.ssw.com.au/. The server that you specified did not return the expected response. Either you have not installed the Team Foundation Server Extensions for SharePoint Products on this server, or a firewall is blocking access to the specified site or the SharePoint Central Administration site. For more information, see the Microsoft Web site (http://go.microsoft.com/fwlink/?LinkId=161206). (type TeamFoundationServerException) Exception Stack Trace:    at Microsoft.TeamFoundation.Client.SharePoint.WssUtilities.VerifyTeamFoundationSharePointExtensions(ICredentials credentials, Uri url)    at Microsoft.TeamFoundation.Admin.VerifySharePointSitesUrl.Verify() Inner Exception Details: Exception Message: TF249064: The following Web service returned an response that is not valid: http://projects.ssw.com.au/_vti_bin/TeamFoundationIntegrationService.asmx. This Web service is used for the Team Foundation Server Extensions for SharePoint Products. Either the extensions are not installed, the request resulted in HTML being returned, or there is a problem with the URL. Verify that the following URL points to a valid SharePoint Web application and that the application is available: http://projects.ssw.com.au. If the URL is correct and the Web application is operating normally, verify that a firewall is not blocking access to the Web application. (type TeamFoundationServerInvalidResponseException) Exception Data Dictionary: ResponseStatusCode = InternalServerError I’ll look at SharePoint after, probably the SharePoint box just needs a restart or a kick If there is a problem with SharePoint it will come out in testing, But I will definatly be passing this on to Microsoft.   Upgrading the SharePoint connector to TFS 2010 You will need to upgrade the Extensions for SharePoint Products and Technologies on all of your SharePoint farm front end servers. To do this uninstall  the TFS 2010 RC from it in the same way as the server, and then install just the RTM Extensions. Figure: Only install the SharePoint Extensions on your SharePoint front end servers. TFS 2010 supports both SharePoint 2007 and SharePoint 2010.   Figure: When you configure SharePoint it uploads all of the solutions and templates. Figure: Everything is uploaded Successfully. Figure: TFS even remembered the settings from the previous installation, fantastic.   Upgrading the Team Foundation Build Servers to TFS 2010 Just like on the SharePoint servers you will need to upgrade the Build Server to the RTM. Just uninstall TFS 2010 RC and then install only the Team Foundation Build Services component. Unlike on the SharePoint server you will probably have some version of Visual Studio installed. You will need to remove this as well. (Coming Soon) Connecting Visual Studio 2010 / 2008 / 2005 and Eclipse to TFS2010 If you have developers still on Visual Studio 2005 or 2008 you will need do download the respective compatibility pack: Visual Studio Team System 2005 Service Pack 1 Forward Compatibility Update for Team Foundation Server 2010 Visual Studio Team System 2008 Service Pack 1 Forward Compatibility Update for Team Foundation Server 2010 If you are using Eclipse you can download the new Team Explorer Everywhere install for connecting to TFS. Get your developers to check that you have the latest version of your applications with SSW Diagnostic which will check for Service Packs and hot fixes to Visual Studio as well.   Technorati Tags: TFS,TFS2010,TFS 2010,Upgrade

  Read the article

• Installing SharePoint 2010 and PowerPivot for SharePoint on Windows 7

  - by smisner

  Many people like me want (or need) to do their business intelligence development work on a laptop. As someone who frequently speaks at various events or teaches classes on all subjects related to the Microsoft business intelligence stack, I need a way to run multiple server products on my laptop with reasonable performance. Once upon a time, that requirement meant only that I had to load the current version of SQL Server and the client tools of choice. In today's post, I'll review my latest experience with trying to make the newly released Microsoft BI products work with a Windows 7 operating system.The entrance of Microsoft Office SharePoint Server 2007 into the BI stack complicated matters and I started using Virtual Server to establish a "suitable" environment. As part of the team that delivered a lot of education as part of the Yukon pre-launch activities (that would be SQL Server 2005 for the uninitiated), I was working with four - yes, four - virtual servers. That was a pretty brutal workload for a 2GB laptop, which worked if I was very, very careful. It could also be a finicky and unreliable configuration as I learned to my dismay at one TechEd session several years ago when I had to reboot a very carefully cached set of servers just minutes before my session started. Although it worked, it came back to life very, very slowly much to the displeasure of the audience. They couldn't possibly have been less pleased than me.At that moment, I resolved to get the beefiest environment I could afford and consolidate to a single virtual server. Enter the 4GB 64-bit laptop to preserve my sanity and my livelihood. Likewise, for SQL Server 2008, I managed to keep everything within a single virtual server and I could function reasonably well with this approach.Now we have SQL Server 2008 R2 plus Office SharePoint Server 2010. That means a 64-bit operating system. Period. That means no more Virtual Server. That means I must use Hyper-V or another alternative. I've heard alternatives exist, but my few dabbles in this area did not yield positive results. It might have been just me having issues rather than any failure of those technologies to adequately support the requirements.My first run at working with the new BI stack configuration was to set up a 64-bit 4GB laptop with a dual-boot to run Windows Server 2008 R2 with Hyper-V. However, I was generally not happy with running Windows Server 2008 R2 on my laptop. For one, I couldn't put it into sleep mode, which is helpful if I want to prepare for a presentation beforehand and then walk to the podium without the need to hold my laptop in its open state along the way (my strategy at the TechEd session long, long ago). Secondly, it was finicky with projectors. I had issues from time to time and while I always eventually got it to work, I didn't appreciate those nerve-wracking moments wondering whether this would be the time that it wouldn't work.Somewhere along the way, I learned that it was possible to load SharePoint 2010 in a Windows 7 which piqued my interest. I had just acquired a new laptop running Windows 7 64-bit, and thought surely running the BI stack natively on my laptop must be better than running Hyper-V. (I have not tried booting to Hyper-V VHD yet, but that's on my list of things to try so the jury of one is still out on this approach.) Recently, I had to build up a server with the RTM versions of SQL Server 2008 R2 and Sharepoint Server 2010 and decided to follow suit on my Windows 7 Ultimate 64-bit laptop. The process is slightly different, but I'm happy to report that it IS possible, although I had some fits and starts along the way.DISCLAIMER: These products are NOT intended to be run in production mode on the Windows 7 operating system. The configuration described in this post is strictly for development or learning purposes and not supported by Microsoft. If you have trouble, you will NOT get help from them. I might be able to help, but I provide no guarantees of my ability or availablity to help. I won't provide the step-by-step instructions in this post as there are other resources that provide these details, but I will provide an overview of my approach, point you to the relevant resources, describe some of the problems I encountered, and explain how I addressed those problems to achieve my desired goal.Because my goal was not simply to set up SharePoint Server 2010 on my laptop, but specifically PowerPivot for SharePoint, I started out by referring to the installation instructions at the PowerPiovt-Info site, but mainly to confirm that I was performing steps in the proper sequence. I didn't perform the steps in Part 1 because those steps are applicable only to a server operating system which I am not running on my laptop. Then, the instructions in Part 2, won't work exactly as written for the same reason. Instead, I followed the instructions on MSDN, Setting Up the Development Environment for SharePoint 2010 on Windows Vista, Windows 7, and Windows Server 2008. In general, I found the following differences in installation steps from the steps at PowerPivot-Info:You must copy the SharePoint installation media to the local drive so that you can edit the config.xml to allow installation on a Windows client.You also have to manually install the prerequisites. The instructions provides links to each item that you must manually install and provides a command-line instruction to execute which enables required Windows features.I will digress for a moment to save you some grief in the sequence of steps to perform. I discovered later that a missing step in the MSDN instructions is to install the November CTP Reporting Services add-in for SharePoint. When I went to test my SharePoint site (I believe I tested after I had a successful PowerPivot installation), I ran into the following error: Could not load file or assembly 'RSSharePointSoapProxy, Version=10.0.0.0, Culture=neutral, PublicKeyToken=89845dcd8080cc91' or one of its dependencies. The system cannot find the file specified. I was rather surprised that Reporting Services was required. Then I found an article by Alan le Marquand, Working Together: SQL Server 2008 R2 Reporting Services Integration in SharePoint 2010,that instructed readers to install the November add-in. My first reaction was, "Really?!?" But I confirmed it in another TechNet article on hardware and software requirements for SharePoint Server 2010. It doesn't refer explicitly to the November CTP but following the link took me there. (Interestingly, I retested today and there's no longer any reference to the November CTP. Here's the link to download the latest and greatest Reporting Services Add-in for SharePoint Technologies 2010.) You don't need to download the add-in anymore if you're doing a regular server-based installation of SharePoint because it installs as part of the prerequisites automatically.When it was time to start the installation of SharePoint, I deviated from the MSDN instructions and from the PowerPivot-Info instructions:On the Choose the installation you want page of the installation wizard, I chose Server Farm.On the Server Type page, I chose Complete.At the end of the installation, I did not run the configuration wizard.Returning to the PowerPivot-Info instructions, I tried to follow the instructions in Part 3 which describe installing SQL Server 2008 R2 with the PowerPivot option. These instructions tell you to choose the New Server option on the Setup Role page where you add PowerPivot for SharePoint. However, I ran into problems with this approach and got installation errors at the end.It wasn't until much later as I was investigating an error that I encountered Dave Wickert's post that installing PowerPivot for SharePoint on Windows 7 is unsupported. Uh oh. But he did want to hear about it if anyone succeeded, so I decided to take the plunge. Perseverance paid off, and I can happily inform Dave that it does work so far. I haven't tested absolutely everything with PowerPivot for SharePoint but have successfully deployed a workbook and viewed the PowerPivot Management Dashboard. I have not yet tested the data refresh feature, but I have installed. Continue reading to see how I accomplished my objective.I unintalled SQL Server 2008 R2 and started again. I had different problems which I don't recollect now. However, I uninstalled again and approached installation from a different angle and my next attempt succeeded. The downside of this approach is that you must do all of the things yourself that are done automatically when you install PowerPivot as a new server. Here are the steps that I followed:Install SQL Server 2008 R2 to get a database engine instance installed.Run the SharePoint configuration wizard to set up the SharePoint databases.In Central Administration, create a Web application using classic mode authentication as per a TechNet article on PowerPivot Authentication and Authorization.Then I followed the steps I found at How to: Install PowerPivot for SharePoint on an Existing SharePoint Server. Especially important to note - you must launch setup by using Run as administrator. I did not have to manually deploy the PowerPivot solution as the instructions specify, but it's good to know about this step because it tells you where to look in Central Administration to confirm a successful deployment.I did spot some incorrect steps in the instructions (at the time of this writing) in How To: Configure Stored Credentials for PowerPivot Data Refresh. Specifically, in the section entitled Step 1: Create a target application and set the credentials, both steps 10 and 12 are incorrect. They tell you to provide an actual Windows user name and password on the page where you are simply defining the prompts for your application in the Secure Store Service. To add the Windows user name and password that you want to associate with the application - after you have successfully created the target application - you select the target application and then click Set credentials in the ribbon.Lastly, I followed the instructions at How to: Install Office Data Connectivity Components on a PowerPivot server. However, I have yet to test this in my current environment.I did have several stops and starts throughout this process and edited those out to spare you from reading non-essential information. I believe the explanation I have provided here accurately reflect the steps I followed to produce a working configuration. If you follow these steps and get a different result, please let me know so that together we can work through the issue and correct these instructions. I'm sure there are many other folks in the Microsoft BI community that will appreciate the ability to set up the BI stack in a Windows 7 environment for development or learning purposes. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• CodePlex Daily Summary for Thursday, February 25, 2010

  CodePlex Daily Summary for Thursday, February 25, 2010New ProjectsAptusSoftware.Threading: AptusSoftware.Threading is a class library designed primarily to assist in the development of multi-threaded WinForm applications, although there i...AxiomGameDesigner: It is going to be a universal scene editor for Axiom 3D game engine. It is in pure C# and will be kept portable to MONO for compatibility with linu...Badger - Unity Productivity Extensions: A set of Microsoft Unity Extensions. Why Badger? Because I love badgers.Business & System Analysis Templates and Best Practices for Russian: http://saway.codeplex.com/Conectayas: Conectayas is an open source "Connect Four" alike game but transformable to "Tic-Tac-Toe" and to a lot of similar games that uses mouse. Written in...FastCode: .NET 3.5 Extensions set to increase coding speed.Hundiyas: Hundiyas is an open source "Battleship" alike game totally written in DHTML (JavaScript, CSS and HTML) that uses mouse. This cross-platform and cro...Icelandic Online Banking: Icelandic Online Banking is project defining a web service interface for online banking.IE8 AddOns XML Creator: Application that helps on creating the xml files for IE8 Accelerators, Search Providers and the markup for Web Slices.iKnowledge: a asp.net mvc demoLearn ASP.NET MVC: Learn ASP.NET MVC is a project for the members of the Peer Learning group in Silicon Valley. It contains the SportsStore solution from the Pro ASP...Live at Education Meta Web-Service: Live at Education Meta Web-Service is intended to abstract from several technologies that are included in Live@edu set of services. This web-ser...Low level wave sound output for VB.NET: Low level sound output class for VB.NET using platform invocation services to call winmm.dllMailQ: MailQ makes it easier for developers to send mail messages from an application. The system sends mails based on a database queue system (store, se...Managed DXGI: Managed DXGI library is Fully managed wrapper writen on C# for DXGI 1.0 and 1.1 technology. It makes easier to support DXGI in managed application....Multivalue AutoComplete WinForms TextBox in C#: This project is a sample application that demonstrates how to create a multivalue WinForms textbox in C# using .NET Framework 3.5.Nifty CSharp Tools: Nifty CSharp Tools, will contain various tools and snippets. IRCBot, splashscreens, linq, world of warcraft log parsing, screenshot uploaders, twi...PHP MPQ: A port of StormLib to PHP for handling Blizzard MPQ files.RedDevils strategy - Project Hoshimi Programming Battle: Source Code of RedDevils strategy. Imagine Cup 2008 - Project Hoshimi Programming Battle.RNUNIT: rNunit is a distributed Nunit project. Many application these days are client-server application, distributed application and regular unit testing ...Samar Solution: Samar Solutions is a business system for office automation.Silverlight OOMRPG Game Engine: Silverlight OOMRPG Game EngineSimulator: GPSSimulatorSLARToolkit - Silverlight Augmented Reality Toolkit: SLARToolkit is a flexible Augmented Reality library for Silverlight with the aim to make real time Augmented Reality applications with Silverlight ...Spiral Architecture Driven Development (SADD) for Russian: Это русская версия сайта sadd.codeplex.comSQLSnapshotManager: Easily manage SQL Server database snapshots in a easy to use visual interface.Twilio with VB.NET MVC: Twilio with VB.NET MVC is a sample application for developing with Twilio's REST based telephony API. It includes an XML Schema of the TwiML respon...Ultra Speed Dial: UltraSpeedDial.com - Online Speed Dial Page.Visual HTML Editor justHTML: justHTML - is simle windows-application WYSIWYG editor that allow everyone - without any knowledge of HTML - to create and edit web-pages. It supp...WinMTR.NET: .NET Clone of the popular Windows clone of the popular Linux Matt's TracerouteWPF Dialogs: "WPF Dialogs" is a library for different Dialogs in WPF (e.g. FolderBrowseDialog, SaveFileDialog, OpenFileDialog etc.). These Dialogs are written i...WPFLogin: A small Login window in WPF and C#XNA PerformanceTimers: CPU Timers for Windows and Xbox360. Can track multiple threads, and presents output as a log on-screen.New ReleasesAptusSoftware.Threading: 2.0.0: First public release. This release is in production as part of several commercial applications and is stable. The source code download includes a...BizTalk Software Factory: BizTalk Software Factory v2.1: This is a service release for the BizTalk Software Factory for BizTalk Server 2009, containing so far: Fix for x64: the SN.EXE tool is now locate...Business & System Analysis Templates and Best Practices for Russian: R00 The Place reserver: Just to reserve the place Will be filled out soonChronos WPF: Chronos v1.0 Beta 2: Added a new SplashScreen Added a new Login View and implemented Log Off Added a new PasswordBoxHelper (http://www.codeproject.com/Articles/371...dotNetTips: dotNetTips.Utility 3.5 R2: This is a new release (version 3.5.0.3) compatible with .NET 3.5. Lots of new classes/features!! Requires SP1 if using the Entity Framework extensi...fleXdoc: template-based server-side document generator (docx): fleXdoc 1.0 beta 3: The third and final beta of fleXdoc. fleXdoc consists of a webservice and a (test)client for the service. Make sure you also download the testclien...FluentPS: FluentPS v1.0: - FluentPS is moved from ASMX to WCF interface of the Project Server Interface (PSI) - Impersonation changes to work in compliance with WCF interfa...FolderSize: FolderSize.Win32.1.0.4.0: FolderSize.Win32.1.0.3.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...iTuner - The iTunes Companion: iTuner 1.1.3707 Beta 3: As promised, the iTuner Automated Librarian is now available. This automatically cleans an entire album of dead tracks and duplicates as tracks ar...Live at Education Meta Web-Service: LAEMWS v 1.0 beta: Release Candidate for LAEMWS.Macaw Reusable Code Library: LanguageConfigurationSolution: This Solution helps developing a multi language publishing web siteManaged DXGI: Initial Release.: Base declaration of interfaces, most of them untested yet.Math.NET Numerics: 2010.2.24.667 Build: Latest alpha buildMiniTwitter: 1.08.1: MiniTwitter 1.08.1 更新内容 変更 インクリメンタル検索時には大文字小文字の区別をしないように変更 クライアント名の表示を本家にあわせて from から via に変更 修正 公式 RT 時にステータスが上に表示されたり二重に表示されるバグを修正 自分が自分へ返信...Multivalue AutoComplete WinForms TextBox in C#: 1.0 First public release: Multivalue autocomplete textbox control and host application in this release are released in a single Visual Studio 2008 projects. See my related b...NMock3: NMock3 - Beta3, .NET 3.5: This release has some exciting new features. Please start providing feedback on the tutorials. The first several are complete and the rest are no...nxAjax - an asp.net ajax library using jQuery: nxAjax v3 codeplex 7: nxAjax v3 codeplex 7 binary and test website. Bug Fixed: ajax:Form control Add: Drag and drop Rewritten: DragnDropManager DragPanel DropPan...Office Apps: 0.8.7: whats new? Document.Editor and Document.Viewer now supports FlowDocument (.xaml) files bug fix'sPDF Rider: PDF Rider 0.3: Application PrerequisitesMicrosoft Windows Operating Systems (XP (tested) - Vista - 7) Microsoft .NET Framework 3.5 runtime A PDF rendering sof...ShellLight: ShellLight 0.1.0.1 Src: Codeplex project released. This is only a preview of the product. Until the first final release there will be many improvements.Silverlight OOMRPG Game Engine: SilverlightGameTutorialSolution v1.01: Please visit my blog for Silverlight OOMROG Game Tutorial: http://www.cnblogs.com/Jax/archive/2010/02/24/1673053.html.Simple Savant: Simple Savant v0.4: Added support for full-text indexing (See Full-Text Indexing) Added support for attribute spanning and compression for property values larger tha...Spiral Architecture Driven Development (SADD) for Russian: R00: R00 to reserve site nameTeamReview - TFS Code Review: Release 1.1.3: Release Features New expanded product positioning for capturing any targeted coding work as a trackable, assignable, reportable Work Item for any r...Text Designer Outline Text Library: 10th minor release: Version 0.3.1 (10th minor release)Fixed the gradient brush being too big for the text, resulting in not much gradient shown in the text. Gradient...TFS Workflow Control: TeamExplorer and TSWA control 1.0 for TFS 2010 RC: This is a special version for TFS 2010 RC. Use the RC version of the power tools to modify the layout of your work items (http://visualstudiogaller...thinktecture WSCF.blue: WSCF.blue V1 Update (1.0.7) - VS2010 RC Support: This update adds support for Visual Studio 2010 RC in addition to Visual Studio 2008. Please note that Visual Studio 2010 Beta 2 is NOT supported a...Tumblen3: tumblen3 Version 25Feb2010: ready for Twitter's xAuthUMD文本编辑器: UMDEditor文本编辑器V2.1.0: 2.1.0 (2010-02-24) 增加查找章节内指定文本内容的功能 2.0.4 (2010-02-06) 章节内容框增加右键菜单，包含编辑文本的基本操作 ------------------------------------------------------- 执行 reg.bat ...VCC: Latest build, v2.1.30224.0: Automatic drop of latest buildVisual HTML Editor justHTML: Latest binary: Latest buid here. Executable and mshtml.dll included in this archive. Ready to use ;)Visual HTML Editor justHTML: Source code for version 2.5: Visual studio 2008 project with full source code.VOB2MKV: vob2mkv-1.0.2: The release vob2mkv-1.0.2 is a feature update of the VOB2MKV project. It now includes a DirectShow source filter, MKVSOURCE. A source filter allo...WinMTR.NET: V 1.0: V 1.0WPF Dialogs: Version 0.1.0: Version 0.1.0 FolderBrowseDialog is implementet for more information look here Version 0.1.0 (german: Version 0.1.0 - Deutsch).WPF Dialogs: Version 0.1.1: Version 0.1.1 Features FolderBrowseDialog was extended / FolderBrowseDialog - Deutsch wurde erweitertXNA PerformanceTimers: XNA PerformanceTimers 0.1: Initial release.Zeta Resource Editor: Release 2010-02-24: Added HTTP proxy server support.Most Popular ProjectsASP.NET Ajax LibraryManaged Extensibility FrameworkWindows 7 USB/DVD Download ToolDotNetZip LibraryMDownloaderVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2MFCMAPIDroid ExplorerUseful Sharepoint Designer Custom Workflow ActivitiesOxiteMost Active ProjectsDinnerNow.netBlogEngine.NETRawrInfoServiceSLARToolkit - Silverlight Augmented Reality ToolkitNB_Store - Free DotNetNuke Ecommerce Catalog ModuleSharpMap - Geospatial Application Framework for the CLRjQuery Library for SharePoint Web ServicesRapid Entity Framework. (ORM). CTP 2Common Context Adapters

  Read the article

• CodePlex Daily Summary for Wednesday, February 24, 2010

  CodePlex Daily Summary for Wednesday, February 24, 2010New ProjectsADO.Net DataSets to ExtJs.data.Store: A JavaScript (and C#) based project to reduce the amount of client-side code necessary to consume ADO.Net / ASP.Net web services when using ExtJS.AMP.Net Wrapper: AMP is a platform to build on-line marketplaces (http://www.poweredbyamp.com). AMP.Net provided Object-Like interaction with AMP's restful service...ArkSwitch: ArkSwitch is an easy to use, finger-friendly task manager for Windows Mobile 6.5.3 (with a WM6.5 compatibility mode). It is developed mainly in C#,...Biffen: Cinema-booking project in Computer Science at University College Nordjylland, Denmark.Braintree Client Library: Client library for integrating with the Braintree Gateway.Business Framework: A framework which helps building business applications. It provides business rules, validation rules and a text-based language for writing rules. I...Camp Araminta: This project will be used to coordinate development efforts on the Camp Araminta website.ChoServiceHost: Simple and easy way to create and host Windows Service Applications in .NET 3.5/Visual Studio 2008Delta College Game Development Project: Project site for cs 16 game development classDotNetNuke® Labs: DotNetNuke Labs is a collection of "research & development" type projects for the DotNetNuke platform.Generic web part for hosting Silverlight content on SharePoint sites (WSS,MOSS): This is a generic web part for hosting Silverlight content on WSS 30 and MOSS 2007 sites. The objective of this web part was to make it easy for us...GpTiming: GpTiming is a simple "lab" application related to race events, based on a Domain Model.HTML Forms in Windows Forms: As the names suggests this code library is designed to introduce HTML code (primarily form code) into Windows Forms. It was created because standar...imgur uploader - .net open source uploader for image sharing site imgur: Imgur uploader strives to be an easy to use uploader for images you would like to share with friends and family. It is written in c#.kuuy static system: kuuy static system is a full static publish website system!LaTeX Grapher: The goal of this project is to make a tool that facilitates making high quality two dimensional vector graphic function plots with a minimal amount...LightREST: A .NET library to consume REST-based HTTP services.Machiavelli: Machiavelli is Stackoverflow inspired project that I am working on following Andrew Siemer's article on DotNetSlackers. Mover: Mover makes it easier for developers to create programmatic animations in Silverlight. It provides an expressive API to the platform's underlying S...MVC Presenter: ASP.NET MVC 2で作るプレゼンビューアーnHibernate Attribute mapping: How to use Attibute mapping with a ManyToMany Relationship with nHibernateNIPO Data Processing Component Framework: NIPO is a general purpose component framework for data processing applications (that follow the IPO-principle). Its plugin-based architecture makes...PowerShell Remote File Explorer: This project intends to develop a Windows forms based file explorer to browse/transfer files over PowerShell 2.0 remoting channel. The file transfe...Process Flow Tracking of Biomass Distribution Project (University of Mumbai): At Larsen & Toubro Infotech India Ltd., my team worked on a SCM (Supply Chain Management) based project titled 'Process Flow Tracking of Biomass Di...VS2010 Rc1 Fix: Illustrates a fix for working with the ASAP.NET Wizard control with VS2010 RC1Yicker: a microblog program devolep by c#.New ReleasesADO.Net DataSets to ExtJs.data.Store: Ext.net: This is the first version of Ext.net. This version contains a single class, Ext.net.Store which extends the Ext.data.Store class to consume ADO.Ne...AMP.Net Wrapper: AMP.Net v1.0: Provides abstraction for all the product search functionality offered by AMP.ArkSwitch: ArkSwitch legacy versions: Old versions - no need to download themArkSwitch: ArkSwitch v1.1.0: ArkSwitch v1.1.0Braintree Client Library: Braintree 1.0.0: Braintree .NET client library 1.0.0Business Framework: BusinessFramework preview: Early preview bits. See Rules for a sample.Business Framework: Samples: SamplesCC.Votd: CC.Votd 1.0.10.224: This is the initial release of CC.Votd. Marking as beta since I'm the only one who has used it up to this point.ChoServiceHost: ChoServiceHost.msi: Easy way to develop Windows Service applications in .NET 3.5/VS.NET 2008. (Installer)ChoServiceHost: ChoServiceHost-Src.zip: Easy way to develop Windows Service applications in .NET 3.5/VS.NET 2008. (Source Files)CHS Extranet: Beta 2.4: Beta 2.4 Release: Change Log: Added HTML preview options for XLS, XLSX, DOCX File Changes: ~/MyComputer.aspx ~/mycomputer.css ~/basestyle.css...Composure: AvalonDock-55751-VS2010.NET4: This is a "convenience build" of AvalonDock (drop 55751) for VIsual Studio 2010 and .NET 4.0. Nothing has been altered in the source code (which ...Data Access Component: Version 2.6: Add LINQ support.Desktop Google Reader: 1.3 Beta 1: New features: Read it Later included (see http://readitlaterlist.com/) Liking added (working: see number of liking users, see if liking yourself,...Explorer Plus: Explorer Plus v0.3: Amazon Locales AddedFree Silverlight & WPF Chart Control - Visifire: Visifire SL and WPF Charts 3.0.3 Released: Hi, Today we have released the final version of Visifire v3.0.3 which contains the following major features: * DataBinding. * IndicatorEn...Generic web part for hosting Silverlight content on SharePoint sites (WSS,MOSS): CTP: The objective of this release was to gather feedback from the wider community. I intend to pursue further development and make fixes wherever appro...HTML Forms in Windows Forms: HTMLForms 1.0: First Release.imgur uploader - .net open source uploader for image sharing site imgur: Release 2010-02-23-01: This is the first codeplex release! Let mayhem commence...Jeremi Stadler: Stick Tops 2.5: Sticktops is a very light program that makes it easy to paste stuff on small notes on the screen. All notes you have is saved on a server so you ca...kuuy static system: kss_v1.0beta sql: kss_v1.0beta sql scripts sourceMDownloader: MDownloader-0.15.2.55998: Fixed detecting uploading.com dead links; Added hiding rss entries without files;Mover: MoverLib for Silverlight 3: A first version of MoverLib for Silverlight 3.nHibernate Attribute mapping: 1.0: Source CodenHibernate Attribute mapping: Download 1: Zip fileNodeXL: Network Overview, Discovery and Exploration for Excel: NodeXL Class Libraries, version 1.0.1.113: The NodeXL class libraries can be used to display network graphs in .NET applications. To include a NodeXL network graph in a WPF desktop or Windo...NodeXL: Network Overview, Discovery and Exploration for Excel: NodeXL Excel 2007 Template, version 1.0.1.113: The NodeXL Excel 2007 template displays a network graph using edge and vertex lists stored in an Excel 2007 workbook. What's NewThis version inclu...OAuthLib: OAuthLib (1.6.0.0): Difference between previous version is as next. 7079 Make it possible to pass factory method of request in ObtainUnauthorizedRequestToken and Reque...patterns & practices SharePoint Guidance: SPG2010 Drop 5: SharePoint Guidance Drop Notes Microsoft patterns and practices ****************************************** ***************************************...PowerShell Remote File Explorer: PSRemoteExplorer 0.1: This release is the initial release of PowerShell remote file explorer. This enables the basic functionality of a remote file explorer. This also p...Reusable Library: v1.0.3: A collection of reusable abstractions for enterprise application developer.SharePoint Outlook Connector: Version 1.0.2.4: Version 1.0.2.4 Minor bugs have been fixed.Silverlight Server File Manager: First production release: This release is in production. Release on change set 37268.SIMD Detector: 2nd Release: Released C/CLI assembly project for use in CSharp and VB. Tested in CSharp console application. A Windows Form application coming soon. Projects ma...Source Analysis Policy: Source Analysis Policy v1.1 SP1: This release contains the compiled, and signed binaries in an installation package. This package also registers the policy with Microsoft Visual St...SpecExpress : A Fluent Validation Framework: SpecExpress 1.1: UpdatesAdded Validation Contexts feature Fixed bug with handling for Bool Types and Required MessageStore now allows for overriding individual ...VCC: Latest build, v2.1.30223.0: Automatic drop of latest buildVS2010 Rc1 Fix: RC1Fix01: This is a very simple project implementing a Microsoft Walkthrough at http://msdn.microsoft.com/en-us/library/wdb4eb30%28VS.100%29.aspx and the man...WPF AutoComplete TextBox Control: version 1.0: Initial releaseMost Popular ProjectsASP.NET Ajax LibraryManaged Extensibility FrameworkAccelerators for Microsoft Dynamics CRMWindows 7 USB/DVD Download ToolDotNetZip LibraryMDownloaderVirtual Router - Wifi Hot Spot for Windows 7 / 2008 R2MFCMAPIDroid ExplorerUseful Sharepoint Designer Custom Workflow ActivitiesMost Active ProjectsDinnerNow.netRawrBlogEngine.NETInfoServiceNB_Store - Free DotNetNuke Ecommerce Catalog ModuleRapid Entity Framework. (ORM). CTP 2SharpMap - Geospatial Application Framework for the CLRjQuery Library for SharePoint Web Servicespatterns & practices – Enterprise LibraryXcoordination Application Space

  Read the article

• CodePlex Daily Summary for Sunday, February 28, 2010

  CodePlex Daily Summary for Sunday, February 28, 2010New ProjectsESB Toolkit Extensions: ESB Extensions is a solution containing multiple .Net Projects and artifacts: Unit Tests, Itineraries, Business Rules, Binding Files, and C# Class ...Event-Based Components Binder: The Binder automatically connects output-pins to input-pins of Event-Based Components based on message type information and naming conventions. ...Haze Anti-Virus: Haze Anti-Virus is a anti virus written in C# and has features such a realtime process watching and a Process Blacklist, and is able to download Da...latex2mathml: A .NET 2.0 library written in C# which allows the conversion of LaTeX documents to XHTML+MathML format. A stand-alone converter is included. The li...Project Lyrebird: Project lyrebird is a attempt to create a all-purpose media player. It is designed to be simple, yet powerful. Its written in C#QueryToGrid Module for DotNetNuke®: This is a module that allows you to execute and display the results of T-SQL queries in DotNetNuke using your choice of AJAX grids.Reusable Library Demo: A demonstration of reusable abstractions for enterprise application developerSharePoint 2010 Conference Samples: This project contains source code from various SharePoint 2010 conferences where Scot Hillier presented.Silverlight Photo Blogger: Silverlight Photo Blogger gives you the tools you need to capture and blog about your travels in a rich and interactive web experience. Enjoy som...SMTP Test: Several times we are faced with applications that send email, the SMTP Tester principle objective is to test various possibilities of sendingSolution Tools - tools for Visual Studio solutions and projects: Solution Tools are a collection of tools that you can use with your Visual Studio Solutions and projects.New ReleasesAgile Poker Cards for Windows Mobile: Agile Poker Cards v1.1.0.0: Agile Poker Cards v1.1.0.0 Use this application to display poker cards in a planning session on a Windows Mobile device. Release notes Added new ...BuildTools - Toolset for automated builds: BuildTools 2.0 Feb 2010 Milestone: The Feb 2010 Milestone release is a complete rewrite of the old codebase in Visual Studio 2010 RC. It features MSBuild tasks for generating build v...Composure: NHibernate-Trunk-2010-02-25-VS2010.NET4 Alpha1: Recent NHibernate-Trunk conversion for Visual Studio 2010 Beta2 against .NET 4.0. Although all of the tests pass (other than the "Ignored"), this ...Employee Scheduler: Employee Scheduler 2.4: Extract the files to a directory and run Lab Hours.exe. Add an employee. Double click an employee to modify their times. Please contact me through ...ESB Toolkit Extensions: Tellago BizTalk ESB 2.0 Toolkit Extensions: Windows Installer file that installs Library on a BizTalk ESB 2.0 system. This Install automatically configures the esb.config to use the new compo...Haze Anti-Virus: Haze Anti-Virus Binary v1.0.3: This is the Compiled version of Haze Anti-Virus, please let me know about any bugs, thanks Please Note that Database updating is currently not avai...Haze Anti-Virus: Haze Anti-Virus Source v1.0.3: This is the source for Haze Anti-VirusHOG Project: HOG Visual Studio Template: This is Visual Studio HOG Template. Created by the great tool: Solution FactoryHOG Project: Template user guide: HOW TOiTuner - The iTunes Companion: iTuner 1.1.3711: Two new features are available: the Automated Librarian and Playlist Exporter. The iTuner Automated Librarian automatically cleans the iTunes libr...johanleino.codeplex.com: SilverlightMultiLevelNavigationExample: The source code for SilverlightMultiLevelNavigationExample (VS 2010)MDownloader: MDownloader-0.15.3.56128: Fixed filefactory provider implementation after site changes.MiniTwitter: 1.09: MiniTwitter 1.09 更新内容 変更 スクロール位置がトップ以外の時は自動更新や発言時に位置を保持するように変更 タブ毎にスクロール位置が変わらないように変更 URL に ? や ! が含まれている時は短縮 URL に変換するように変更NMock3: NMock3 - Beta 4, .NET 3.5: This release includes the most current version of the NMock2 project code from Source Forge. Please start providing feedback on the tutorials. The...QueryUnit: QueryUnitPOC v. 0.0.0.7: - This version fixes problems related to the fact that in previous releases you had to specify expected values using locale-specific formats. Now e...RapidWebDev - .NET Enterprise Software Development Infrastructure: RapidWebDev 1.51: This is a hot-fix version for 1.5 which is added a new restful web service for concrete data and fixed some major bugs. The change list is as follo...Rawr: Rawr 2.3.11: - Load from Armory code cleaned up. - Tiny Abomination in a Jar's proc how now been more accurately modeled. - You should now be able to reload...Resharper Settings Manager: RSM v1.2: Changes Added Default Settings File option. The selected settings file will be loaded automatically for solutions with no settings sharing. Added...Reusable Library Demo: Reusable Library Demo v1.0.0: A demonstration of reusable abstractions for enterprise application developerRounded Corners / DIV Container: MJC RoundedDiv 3.2: This is the first public release on Codeplex.com. Versions previous to 3.2 were created before this control was made available on Codeplex.com.SharePoint 2010 Conference Samples: Samples: Download the samples from the conferencesSharePoint Outlook Connector: Version 1.2.2.8: Saving email message as list item and attachments as attachment of the list item functionality has been addedSharePoint URL Ping Tool: Url Ping Tool Solution: A solution that contain one fram fature that will add a link under Site Administration section in the Site Settings page.SMTP Test: Fist SMTP Tester: First ReleaseSolution Tools - tools for Visual Studio solutions and projects: SolutionTools binary: Initial release of the tool. Turns out, this project was just a big waste of effort - use Project Linker instead!Solution Tools - tools for Visual Studio solutions and projects: SolutionTools source - don't use this tool: Initial release of the tool. Turns out, this project was just a big waste of effort - use Project Linker instead! Anyway, here's the source code...Spark View Engine: Spark v1.1 RC1: Overview This build is a preview of v1.1. Among other changes it provides support for ASP.NET MVC 2 RC2. Spark v1.1 release will be created soon ...Sprite Sheet Packer: 2.0 Release: I'm calling this a full new release because I can. Refactored all of the build logic to sspack.exe. This allows you to run this from the command l...SPSF SharePoint Software Factory: SPSF SharePoint Software Factory 2.4.3: New features: WSPBuilder support, Simple Application now with optional multilanguage support, Extending deployment skript for large deployments Fix...TortoiseHg: Beta for TortoiseHg 1.0 (0.9.31201): Beta for TortoiseHg 1.0 (0.9.31201) Please backup your user Mercurial.ini file and then uninstall any 0.9.X release before installing Use the x86...UI Compiler .NET - JavaScript compiler/minifier built on Google Closure Compiler: UI Compiler .NET 1.5 Beta: UI Compiler .NET does not include Java. To be able to run Google Closure Compiler locally you must make sure that Java 6 is installed. If Java 6 (o...VCC: Latest build, v2.1.30227.0: Automatic drop of latest buildVisual Studio DSite: File Encryption and Decryption (Visual Basic 2008): This program will create an encrypted copy of the file specified. Also decrypt the file specified. This program contains the source code but if yo...Visual Studio DSite: Visual C++ 2008 CLR Console Application Random Int: This source code includes an example of generating a random integer between the numbers 1-100.Weather Forecast Control: MJC MyWeather 2.2: This is the first public release on Codeplex.com. Versions previous to 2.2 were created before this control was made available on Codeplex.com.Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)Microsoft SQL Server Community & SamplesASP.NETDotNetNuke® Community EditionBlogEngine.NETMost Active ProjectsDinnerNow.netRawrBlogEngine.NETMapWindow GISSLARToolkit - Silverlight Augmented Reality ToolkitCommon Context Adapterspatterns & practices – Enterprise LibrarySharpMap - Geospatial Application Framework for the CLRNB_Store - Free DotNetNuke Ecommerce Catalog ModuleRapid Entity Framework. (ORM). CTP 2

  Read the article

< Previous Page | 77 78 79 80 81 82 83 84 85 86 87  | Next Page >