Search Results

Search found 7616 results on 305 pages for 'ratn deo dev'.

Page 81/305 | < Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >

• USB drives not recognized all of a sudden (module usb_storage not loading)

  - by Siddharth

  I am very close to the solution, just need to know how to get usb-storage to load I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• How to Create a bootable Ubuntu USB flash drive from terminal

  - by Avinash Raj

  Is there any possibility to create a Ubuntu USB flash drive from terminal without using any third-party applications like YUMI,Unetbootin,etc. I tried to create a bootable ubuntu flash drive with dd method, sudo umount /dev/sdb sudo dd if=/path/to/ubuntu.iso of=/dev/sdb bs=1M It create files on the USB disk,but when i try to boot the usb disk it says Operating System Not Found error. Any help will be appreciated!

  Read the article

• Mounting a drive in Ubuntu 9.10 (Karmic Koala)

  - by morpheous

  I have just installed Ubuntu on a machine that previously had XP installed on it. The machine has 2 HDD (hard disk drives). I opted to install Ubuntu completely over XP. I am new to Linux, and I am still learning how to navigate teh file structure. However, AFAICT), there is only one drive. I want to be able to store programs etc on the first drive, and store data (program output etc) on the second drive. It appears Ubuntu is not aware that I have 2 drives (on XP, these were drives C and D). How can I mount the second drive (ideally, I want to do this automatically on login, so that the drive is available to me whenever I login - withou manual intervention from me) In XP, I could refer to files on a specific drive by prefixing with the drive letter (e.g. c:\foobar.cpp and d:\foobar.dat). I suspect the notation on ubuntu is different. How may I specify specific files on different drives? Last but notbthe least (a bit unrelated to previous questions). This relates to direcory structure again. I am a developer (C++ for desktops and PHP for websites), I want to install the following apps/ libraries. i). Apache 2.2 ii). PHP 5.2.11 iii). MySQL (5.1) iv). SVN v). Netbeans vi). C++ development tools (gcc, gdb, emacs etc) vii). QT toolkit viii). Some miscellaeous scientific software (e.g. www.r-project.org, www.gnu.org/software/octave/) I would be grateful if a someone can recommend a directory layout for these applications. Regarding development, I would also be grateful if someone could point out where to store my project and source files i.e: (i) *.cpp, *.hpp, *.mak files for cpp projects (ii) individual websites On my XP machine the layout for C++ dev was like this: c:\dev\devtools (common libs and headers etc) c:\dev\workarea (root folder for projects) c:\dev\workarea\c++ (c++ projects) c:\dev\workarea\websites (web projects) I would like to create a similar folder structure on the linux machine, but its not clear whether to place these folders under /, /usr, /home or swomewhere else (there seems to be abffling number of choices, so I want to get it "right" first time - i.e having a directory structure that most developer use, so it is easier when communicating with other ubuntu/linux developers)

  Read the article

• Keeping up with New Releases

  - by Jeremy Smyth

  You can keep up with the latest developments in MySQL software in a number of ways, including various blogs and other channels. However, for the most correct (if somewhat dry and factual) information, you can go directly to the source.  Major Releases  For every major release, the MySQL docs team creates and maintains a "nutshell" page containing the significant changes in that release. For the current GA release (whatever that is) you'll find it at this location: https://dev.mysql.com/doc/mysql/en/mysql-nutshell.html  At the moment, this redirects to the summary notes for MySQL 5.6. The notes for MySQL 5.7 are also available at that website, at the URL http://dev.mysql.com/doc/refman/5.7/en/mysql-nutshell.html, and when eventually that version goes GA, it will become the currently linked notes from the URL shown above. Incremental Releases  For more detail on each incremental release, you can have a look at the release notes for each revision. For MySQL 5.6, the release notes are stored at the following location: http://dev.mysql.com/doc/relnotes/mysql/5.6/en/ At the time I write this, the topmost entry is a link for MySQL 5.6.15. Each linked page shows the changes in that particular version, so if you are currently running 5.6.11 and are interested in what bugs were fixed in versions since then, you can look at each subsequent release and see all changes in glorious detail. One really clever thing you can do with that site is do an advanced Google search to find exactly when a feature was released, and find out its release notes. By using the preceding link in a "site:" directive in Google, you can search only within those pages for an entry. For example, the following Google search shows pages within the release notes that reference the --slow-start-timeout option:     site:http://dev.mysql.com/doc/relnotes/mysql/ "--slow-start-timeout" By running that search, you can see that the option was added in MySQL 5.6.5 and also rolled into MySQL 5.5.20.   White Papers Also, with each major release you can usually find a white paper describing what's new in that release. In MySQL 5.6 there was a "What's new" whitepaper at this location: http://www.mysql.com/why-mysql/white-papers/whats-new-mysql-5-6/ You'll find other white papers at: http://www.mysql.com/why-mysql/white-papers/ Search the page for "5.6" to see any papers dealing specificallly with that version.

  Read the article

• Puppet - Possible to use software design patterns in modules?

  - by Mike Purcell

  As I work with puppet, I find myself wanting to automate more complex setups, for example vhosts for X number of websites. As my puppet manifests get more complex I find it difficult to apply the DRY (don't repeat yourself) principle. Below is a simplified snippet of what I am after, but doesn't work because puppet throws various errors depending up whether I use classes or defines. I'd like to get some feed back from some seasoned puppetmasters on how they might approach this solution. # site.pp import 'nodes' # nodes.pp node nodes_dev { $service_env = 'dev' } node nodes_prod { $service_env = 'prod' } import 'nodes/dev' import 'nodes/prod' # nodes/dev.pp node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo': } httpd::vhost::package::site { 'bar': } } # modules/vhost/package.pp class httpd::vhost::package { class manage($port) { # More complex stuff goes here like ensuring that conf paths and uris exist # As well as log files, which is I why I want to do the work once and use many notify { $service_env: } notify { $port: } } define site { case $name { 'foo': { class 'httpd::vhost::package::manage': port => 20000 } } 'bar': { class 'httpd::vhost::package::manage': port => 20001 } } } } } That code snippet gives me a Duplicate declaration: Class[Httpd::Vhost::Package::Manage] error, and if I switch the manage class to a define, and attempt to access a global or pass in a variable common to both foo and bar, I get a Duplicate declaration: Notify[dev] error. Any suggestions how I can implement the DRY principle and still get puppet to work? -- UPDATE -- I'm still having a problem trying to ensure that some of my vhosts, which may share a parent directory, are setup correctly. Something like this: node 'service1.ownij.lan' inherits nodes_dev { httpd::vhost::package::site { 'foo_sitea': } httpd::vhost::package::site { 'foo_siteb': } httpd::vhost::package::site { 'bar': } } What I need to happen is that sitea and siteb have the same parent "foo" folder. The problem I am having is when I call a define to ensure the "foo" folder exists. Below is the site define as I have it, hopefully it will make sense what I am trying to accomplish. class httpd::vhost::package { File { owner => root, group => root, mode => 0660 } define site() { $app_parts = split($name, '[_]') $app_primary = $app_parts[0] if ($app_parts[1] == '') { $tpl_path_partial_app = "${app_primary}" $app_sub = '' } else { $tpl_path_partial_app = "${app_primary}/${app_parts[1]}" $app_sub = $app_parts[1] } include httpd::vhost::log::base httpd::vhost::log::app { $name: app_primary => $app_primary, app_sub => $app_sub } } } class httpd::vhost::log { class base { $paths = [ '/tmp', '/tmp/var', '/tmp/var/log', '/tmp/var/log/httpd', "/tmp/var/log/httpd/${service_env}" ] file { $paths: ensure => directory } } define app($app_primary, $app_sub) { $paths = [ "/tmp/var/log/httpd/${service_env}/${app_primary}", "/tmp/var/log/httpd/${service_env}/${app_primary}/${app_sub}" ] file { $paths: ensure => directory } } } The include httpd::vhost::log::base works fine, because it is "included", which means it is only implemented once, even though site is called multiple times. The error I am getting is: Duplicate declaration: File[/tmp/var/log/httpd/dev/foo]. I looked into using exec, but not sure this is the correct route, surely others have had to deal with this before and any insight is appreciated as I have been grappling with this for a few weeks. Thanks.

  Read the article

• Is Unix/Linux adoption a measure of developer skill? [closed]

  - by adeptsage

  Is Linux/Unix based OS adoption for development (or recreation) a rough measure of the awareness, adaptability and/or skill of a developer, after considering factors like learning curve for effective code testing via the CLI, basic scripting, tweaking, etc. I have no intention of starting flame wars between Windows and Linux as better dev environments, and personal choice of OSes for dev, but what i do wish to know is that - will the level of adaptability of a person who uses a Unix based system be defined by the fact that he programs on a Unix based OS?

  Read the article

• Fedora 13 post security update boot problem

  - by Alex

  Hello. About a month ago I installed a security update that had new Kernek 2.6.34.x from 2.6.33.x), this is when the problem occurred for the first time. After the install my computer would not boot at all, black screen without any visible hard drive activity (I gave it good 30 minutes on black screen, before took actions)... I poped in installation DVD and went in rescue mode to change back the boot option to old kernel (was just a guess where the problem was). After restart computer loaded just file, took a long time for it to start because of SELinux targeted policy relabel is required. Relabeling could take very long time depending on file size. I assumed that the update got messed up somehow and continued working with modified boot option. Couple of days ago, there was another kernel update. I installed it and same problem as before. This rules out corrupted update theory... Black screen right after 'BIOS' screen before OS gets loaded. I had to rescue system again... Below is copy of my grub.conf file. I am fairly new to LINUX (couple of years of experience), mostly development and basic config... nothing crazy. # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_obalyuk-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=2 timeout=0 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.34.6-54.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-54.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-54.fc13.i686.PAE.img title Fedora (2.6.34.6-47.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.34.6-47.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.34.6-47.fc13.i686.PAE.img title Fedora (2.6.33.8-149.fc13.i686.PAE) root (hd0,0) kernel /vmlinuz-2.6.33.8-149.fc13.i686.PAE ro root=/dev/mapper/vg_obalyuk-lv_root rd_LVM_LV=vg_obalyuk/lv_root rd_LVM_LV=vg_obalyuk/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet initrd /initramfs-2.6.33.8-149.fc13.i686.PAE.img I like my system to be up to date... Let me know if I can post any other files that can be of help. Has anyone else had this problem? Does anyone has any ideas how to fix this problem? p.s. Anything helps, you ppl are great! thx for ur time.

  Read the article

• USB drives not recognized all of a sudden (usb_storage not loaded lsmod does not report usb_storage)

  - by Siddharth

  I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• execute script with sudo after login

  - by Kalamalka Kid

  i need to execute the following commands AFTER login. sudo hdparm -y /dev/disk/by-uuid/443AFBAD7FE50945 sudo hdparm -y /dev/disk/by-uuid/7ABB49654B799D40 (trying to edit rc.local does not work nor does using hdparm.conf because as soon as I log in the disks start up again). I have tried numerous things like bash files and autossh entries in the startup applications with no luck because sudo is involved.

  Read the article

• Ubuntu unattended-upgrades stops apache

  - by Robbie

  This morning i was alerted to the fact that both apache instances serving my app were not responding to requests from my load balancer. I attempted apachectl restart and it said apache was not running. So, i started apache on both instances and got the service up again. I then followed the logs and worked out that both had performed upgrades via the unattended-upgrades package moments before they stopped responding. /var/log/unattended-upgrades/unattended-upgrades.log 2013-07-02 06:30:51,875 INFO Starting unattended upgrades script 2013-07-02 06:30:51,875 INFO Allowed origins are: ['o=Ubuntu,a=precise-security'] 2013-07-02 06:33:57,771 INFO Packages that are upgraded: accountsservice apache2 apache2-mpm-prefork apache2-utils apache2.2-bin apache2.2-common apparmor apport apt apt-transport-https apt-utils bind9-host binutils dbus dnsutils gnupg gpgv isc-dhcp-client isc-dhcp-common krb5-locales libaccountsservice0 libapt-inst1.4 libapt-pkg4.12 libbind9-80 libc-bin libc-dev-bin libc6 libc6-dev libcurl3-gnutls libdbus-1-3 libdbus-glib-1-2 libdns81 libdrm-intel1 libdrm-nouveau1a libdrm-radeon1 libdrm2 libexpat1 libfreetype6 libgc1c2 libgnutls-dev libgnutls-openssl27 libgnutls26 libgnutlsxx27 libisc83 libisccc80 libisccfg82 liblwres80 libruby1.8 libx11-6 libx11-data libxcb1 libxext6 libxml2 linux-firmware linux-image-virtual linux-libc-dev linux-virtual multiarch-support openssl perl perl-base perl-modules python-apport python-crypto python-keyring python-problem-report python-software-properties ri1.8 ruby1.8 ruby1.8-dev sudo tzdata update-manager-core 2013-07-02 06:33:57,772 INFO Writing dpkg log to '/var/log/unattended-upgrades/unattended-upgrades-dpkg_2013-07-02_06:33:57.772399.log' 2013-07-02 06:36:10,584 INFO All upgrades installed I'm running Ubuntu 12.04 on Amazon EC2 servers. I have unattended-upgrades installed and configured as follows: /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these (origin:archive) pairs Unattended-Upgrade::Allowed-Origins { "${distro_id}:${distro_codename}-security"; // "${distro_id}:${distro_codename}-updates"; // "${distro_id}:${distro_codename}-proposed"; // "${distro_id}:${distro_codename}-backports"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { }; /etc/apt/apt.conf.d/20auto-upgrades APT::Periodic::Update-Package-Lists "1"; APT::Periodic::Unattended-Upgrade "1"; I've struggled to find documentation about what happens to running processes during an upgrade. - Is this expected behaviour? Or should unattended-upgrades restart apache after upgrading it? - What can I do to ensure apache is restarted correctly? Should I just blacklist the apache package?

  Read the article

• Créer des QR Codes avec Zxing et Java 2D en 5 minutes, par Thierry Leriche-Dessirier

  Bonjour, Je vous propose un article intitulé "Créer des QR Codes avec Zxing et Java 2D, en 5 minutes". Ce petit article s'intéresse à la génération de QR codes en Java. Nous allons voir qu'il est relativement simple de créer une matrice de modules à l'aide de Zxing puis d'en faire une jolie image avec Java 2D. L'article est visible ici : http://thierry-leriche-dessirier.dev...-java2d-5-min/ Et je vous invite aussi à lire mes autres articles ici : http://thierry-leriche-dessirier.dev...#page_articles ...

  Read the article

• Windows Phone 8 SDK

  - by Nikita Polyakov

  Yesterday, the new Windows Phone 8 was announced! Find out more about the cool new OS and the new devices supporting it at www.WindowsPhone.com Today at BUILD conference in Redmond, WA – Microsoft has announced general availability of the Developer SDK for Windows Phone 8! Get the SDK and more info in the dev center: http://dev.WindowsPhone.com Also watch the Windows Phone Developer blog. Also this is the best time to join the Windows Phone Store for just for $8 for next 8 days.

  Read the article

• Mounting a usb floppy disk drive in Ubuntu 11.04

  - by Jocky B

  I have tried to mount my usb floppy disk drive in 11.04 Natty. So far I have managed to use the udisks --mount/dev/sdf command in terminal, but get a message that I have not stated a filetype "john@john-desktop:~$ udisks --mount /dev/sdf Mount failed: Error mounting: mount: you must specify the filesystem type" This is the result I get when trying to mount the usb floppy disk drive. Anyone know how to proceed Cheers

  Read the article

• Swap is encrypted or not?

  - by Abhijit Navale

  I selected to encrypt home folder while install lubuntu 12.10 (64 bit) But after that 'sometimes' I get error that can not find /dev/mapper/cryptswap1 wait for mount or cancel at slpash screen. It then start the lubuntu without any problem. If i do sudo blkid | grep swap [sudo] password for abhijit: /dev/mapper/cryptswap1: UUID="fce3ef14-a9c6-45ac-81f5-18ff415851b0" TYPE="swap" That means swap is encrypted. But if i go to gparted it shows unknown partition with red exclamation mark for swap.

  Read the article

• GUVCVIEW errors

  - by Brian Snapp

  I had GUVCVIEW working once before. it suddenly quit working. This is the error I receive........ bt_audio_service_open: connect() failed: Connection refused (111) bt_audio_service_open: connect() failed: Connection refused (111) bt_audio_service_open: connect() failed: Connection refused (111) bt_audio_service_open: connect() failed: Connection refused (111) video device: /dev/video0 /dev/video0 - device 1 Init. Intergrated Webcam (location: usb-0000:00:1a.7-2) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1024, height = 768 } Time interval between frame: 1/9, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/9, 1/5, checking format: 1196444237 Format unavailable: 1196444237. Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 /dev/video0 - device 1 Init. Intergrated Webcam (location: usb-0000:00:1a.7-2) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1024, height = 768 } Time interval between frame: 1/9, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/9, 1/5, checking format: 1448695129 Requested Format unavailable: get width 640 height 480 vid:0c45 pid:6410 driver:uvcvideo (guvcview:4079): Gtk-CRITICAL **: gtk_hscale_new_with_range: assertion `min < max' failed (guvcview:4079): Gtk-CRITICAL **: gtk_scale_set_draw_value: assertion `GTK_IS_SCALE (scale)' failed Segmentation fault I suppose the problem lies in the fact, that I cannot locate a configuration file to edit. Any help in where this file may lie? I have tried searching for any/everything related to guvcview, and have had zero success. Thank you for taking the time to read this, and hopefully providing a solution..

  Read the article

• DVD ROM is not working

  - by Cyril N.

  (note: I don't know in which StackExchange site to put this question, I'll thank the moderator that will move it to a more appropriate place, if there is a S.E. available for my question). I have a DVD RW drive that is well listed in the bios, and if no CD is in, it is also present in the "My Computer" of my Fedora 16. But when I put a disc on it, the icon disapear from "My Computer", and I can not do anything with this ! (Like erasing a RW disc). I'd like to boot a Fedora 17 Live CD image. I burned it on an other computer but when I try to run it in bios, nothing is done and I'm redirected to Grub of my HD. The command cdrecord -scanbus shows this : wodim: Warning: controller returns wrong size for CD capabilities page. wodim: Cannot get CD capabilities data. 6,1,0 601) 'HD-DT%ST' 'DVD%RAM G@22NP20' '1&04' Removable CD-ROM And when I try to mount manually the disc, I got this error : mount: block device /dev/sr0 is write-protected, mounting read-only mount: /dev/sr0: can't read superblock Here's a paste of dmesg | grep sr0 : [ 5.161265] sr0: scsi-1 drive [ 5.161621] sr 6:0:1:0: Attached scsi CD-ROM sr0 [ 834.545978] sr0: Hmm, seems the drive doesn't support multisession CD's [ 841.731194] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 842.021640] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 842.021652] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 842.021662] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 842.021672] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 [ 842.021688] end_request: I/O error, dev sr0, sector 0 [ 842.021697] Buffer I/O error on device sr0, logical block 0 [ 842.023715] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 843.048203] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 843.048211] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 843.048219] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 843.048234] end_request: I/O error, dev sr0, sector 0 [ 843.048274] EXT4-fs (sr0): unable to read superblock [ 843.063155] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 843.075904] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 843.220512] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 843.220522] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 843.220530] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 843.220538] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 843.220553] end_request: I/O error, dev sr0, sector 0 [ 843.220609] FAT-fs (sr0): unable to read boot sector The lines from Sense Key .. (line 6) to DRIVER_SENSE (line 11) are repeating a lot. I then changed my DVD player with an other spare one I had, and the disc didn't boot neither. I then changed the IDE cable, but still no success. What can I do to make it work? Thanks for your help.

  Read the article

• In which cases build artifacts will be different in different environments

  - by Sundeep

  We are working on automation of deployment using Jenkins. We have different environments - DEV, UAT, PROD. In SVN, we are tagging each release and placing same binaries in DEV, UAT, PROD. The artifacts already contains config files w.r.t each environment but I am not understanding why we are storing binaries in environment folder again. Are there any scenarios where deployment might be different for different environments.

  Read the article

• Ubuntu Install 11.10 doesn't recognize Windows 7 installation with new HDD

  - by arlendo

  Replaced my crashed HDD with a Seagate 2TB Sata (bought from a company who pulled it from a working computer, OS unknown) and did a fresh install of Windows 7. Windows shows 100MB boot partition (bootable NTFS) and 200GB Windows partition (NTFS), the rest is unallocated. Win7 Disk Management says the partitioning type is Master Boot Record. Win7 boots and runs fine. Ubuntu 11.10 Install procedes to Allocate Drive Space screen and should say This computer currently has Windows 7 on it. What would you like to do? Instead, it says something like Install doesn't detect any existing OS on this computer. When I click on Something else, the partition table shows only the unallocated space of 1.8TB. Ubuntu Disk Utility says Partitioning: Master Boot Record, but GParted Live says Partition Table: gpt. It was my original intention to have the Windows boot partition and application partition, then install Ubuntu 11.10 using boot, root, swap, and home partitions, and maybe another partition just for data (mostly photos). Currently, I would be happy if I could just get Ubuntu installed along with Win7. I am aware of the MBR limits of 3 Primary partitions and 1 Extended partition. I suspect that my new HDD is partitioned for GPT and that is why Ubuntu can't see the Win7 installation. Am I on the right track? I was going to use Windows Disk Management to convert GPT to MBR but I only have the one drive on my AMD-64 mini-computer and it says I have to empty the drive of all partitions before I can access the Convert command. And I can't find any bootable software that would allow me to do that conversion. Here is the result of sudo fdisk -l: ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 224 heads, 19 sectors/track, 918004 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd4a68c18 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 419637247 209715200 7 HPFS/NTFS/exFAT ubuntu@ubuntu:~$ Keep in mind that I'm a definite newbie to screwing around with the inner workings of Ubuntu. I previously had Ubuntu 10.04 running with Vista and I don't remember even having to partition anything that wasn't automatic in the install. Thanks for taking a look here. My Win7 is running fine but I miss my Ubuntu.

  Read the article

• Ubuntu Dual Screen Using Virtual Machine - AMD GPU

  - by Chris

  I've been searching online and reading tutorials and etc about how to make my ubuntu VM dual screen(x86_64). I have first tried to run these commands: sudo aticonfig --initial -f which gave me the ouput of: sudo: aitconfig: command not found I then googled the output and followed these instructions that I tells me to install my ATI drivers onto my ubuntu. wget http://www2.ati.com/drivers/linux/ati-driver-installer-11-5-x86.x86_64.run sudo sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Ubuntu/natty sudo dpkg -i *.deb sudo apt-get -f install sudo aticonfig -f --initial --adapter=all sudo reboot It all works well until I input sudo apt-get -f install which gives me the following output: sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 25 not upgraded. 3 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up fglrx (2:8.850-0ubuntu1) ... update-alternatives: error: alternative link /usr/bin/aticonfig is already managed by x86_64-linux-gnu_gl_conf. dpkg: error processing fglrx (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of fglrx-amdcccle: fglrx-amdcccle depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-amdcccle (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of fglrx-dev: fglrx-dev depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-dev (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: fglrx fglrx-amdcccle fglrx-dev E: Sub-process /usr/bin/dpkg returned an error code (1) At this point, I don't know what to do since running: gksudo amdcccle For the record, I have 3D acceleration turned on. The following is my GPU for my VM lspci | grep VGA 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter Any Help on how I can make my VM dual screen with Ubuntu would be great. Thank you in advance.

  Read the article

• 2 windows loaders after grub2 repair

  - by adi

  I have recently reinstalled w7 and had ubuntu 12.04 lts installed on it,w7 installation deleted the grub2 loader,after that i found solution to use boot-repair from live-cd session, BUT......now i have 2 windows 7(loader)in grub loader,and only 1 windows 7 installation,how can i remove it?One is on on /dev/sda1(which should be w7 sistem reserved partition) and second is on on /dev/sda2(which is w7 installment partition) it says and both log on same w7.All i need is to remove it without brake the grub2 again and if someone is willing to guide me to add windows on primary selection, cause my girlfriends doesnt get along with linux :D.

  Read the article

• apcupsd on Linux does not report on APC BackUPS Pro 900

  - by lserni

  From what documentation I could find, the UPS should be (is!) supported by Linux and ought to work with apcupsd. I looked for specific problems such as the infamous Microlink protocol, and found none. I have found a feedback from a guy in UK that reports using this very model on a not-too-different OS version (his OpenSuSE 12.1, mine 12.3 x86_64). The USB port is detected, lsusb reports Bus 002 Device 003: ID 051d:0002 American Power Conversion Uninterruptible Power Supply and lsusb -v -s002:003 confirms and expands: Bus 002 Device 003: ID 051d:0002 American Power Conversion Uninterruptible Power Supply Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x051d American Power Conversion idProduct 0x0002 Uninterruptible Power Supply bcdDevice 0.90 iManufacturer 1 American Power Conversion iProduct 2 Back-UPS RS 900G FW:879.L4 .I USB FW:L4 bNumConfigurations 1 Configuration Descriptor: [...] Interface Descriptor: [...] bInterfaceClass 3 Human Interface Device bInterfaceSubClass 0 No Subclass bInterfaceProtocol 0 None iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.00 bCountryCode 33 US bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 1134 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 100 Device Status: 0x0000 (Bus Powered) The kernel recognizes this and duly sets up crw------- 1 root root 180, 96 Nov 4 16:11 /dev/usb/hiddev0 As far as I know, everything is as it should be. I have put the standard configuration in /etc/apcupsd/apcupsd.conf (which is Unix-terminated, ASCII-only, no BOM (just in case)) UPSCABLE usb UPSTYPE usb DEVICE (I have also tried commenting out DEVICE, and setting a device of /dev/puppa results in an access attempt to /dev/puppa, not some /var/lib/dev/puppa or /dev/puppa\r\n). Yet, what apcaccess tells me is VERSION : 3.14.10 (13 September 2011) suse CABLE : USB Cable DRIVER : USB UPS Driver UPSMODE : Stand Alone STARTTIME: 2013-11-04 16:24:22 +0100 MODEL : STATUS : NOBATT LINEV : 000.0 Volts LOADPCT : 0.0 Percent Load Capacity BCHARGE : 000.0 Percent TIMELEFT : 0.0 Minutes MBATTCHG : 5 Percent MINTIMEL : 3 Minutes MAXTIME : 0 Seconds SENSE : Low LOTRANS : 000.0 Volts HITRANS : 000.0 Volts It doesn't recognize the model, and reports no battery (and no voltage). This confirms that it's not the Microlink problem, or it would report the battery status, if precious little else. If I disconnect the USB cable, I get an apcupsd message to the effect that communications have been lost; and I get the "communication restored" broadcast too, if I reconnect the cable. apcupsd is monitoring. So everything tells me that it should work -- only it doesn't. Does anyone spot what I'm missing?

  Read the article

• How do I mount a USB floppy disk drive?

  - by Jocky B

  I have tried to mount my usb floppy disk drive in 11.04 Natty. So far I have managed to use the udisks --mount/dev/sdf command in terminal, but get a message that I have not stated a filetype john@john-desktop:~$ udisks --mount /dev/sdf Mount failed: Error mounting: mount: you must specify the filesystem type This is the result I get when trying to mount the usb floppy disk drive. Anyone know how to proceed?

  Read the article

• HAproxy roundrobin balancing does not appear to be distributing evently

  - by andrew

  Hello, I know that with loaded servers, roundrobin in HAproxy (1.4.4) does not evenly distribute, but my servers are currently getting NO traffic (test setup), and roundrobin balancing does www1,www1,www1,www1,www1,...www2,www2,www2,...,www1... I'm verifying this by having the script being run on each server cat /etc/HOSTNAME (slackware). I need to have it switch back and forth each time to test some session stuff (stored in shared memcached) but am having trouble getting it to switch between my two web servers on each request. global log 127.0.0.1 local0 warning maxconn 4096 chroot /usr/share/haproxy pidfile /var/run/haproxy.pid uid 99 gid 99 daemon defaults balance roundrobin fullconn 100 maxconn 4096 mode http option dontlognull option http-server-close option forwardfor option redispatch retries 3 timeout connect 5000 timeout client 20000 timeout server 60000 timeout queue 60000 stats enable stats uri /haproxy stats auth ***:*** frontend www *:80 log global acl is_upload hdr_dom(host) -i uploads.site.com acl is_api hdr_dom(host) -i api.site.com acl is_dev hdr_dom(host) -i dev.site.com acl is_apidev hdr_dom(host) -i apidev.site.com use_backend uploads.site.com if is_upload use_backend api.site.com if is_api use_backend dev.site.com if is_dev !is_apidev default_backend site.com backend site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend api.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:api.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend dev.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:dev.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 backend uploads.site.com option httpchk HEAD /alive.php HTTP/1.1\r\nHost:uploads.site.com server www1 1.1.1.1:8080 weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 server www2 1.1.1.2:8080 backup weight 10 minconn 5 maxconn 25 check inter 2000 rise 2 fall 2 So basically, I have some different back-ends (I've verified the ACLs are working), with the default option "roundrobin" selected. I've tried removing weights, removing the minconn/maxconn/fullconn attributes for all servers (not just the backend I'm testing), tried removing the ACLs, etc. I've been testing on dev.site.com BTW. Anyone see a reason why I can't get something like www1,www2,www1,www2,...? Also, this is one of my first questions on here, so please let me know if I left anything needed out of my post. Thanks!

  Read the article

• What to do when opensource project starts to tear apart? (or a manager tries to write code and than shouts at the team)

  - by Kabumbus

  Imagine there is an open source cross-platform project on Google code. It has lots of revisions (1000). It concentrates in itself lots technological stuff - rare stuff - it mixes top tech. It contains server, and more than one client. The project was created by a well-connected team of developers (friends) and a manager that was sponsoring project at its start up during its first few months (project now is more than a year old-sponsoring oss project is a big good deal- also gave the idea of project to developers). The project was growing in complexity and effort reqiered to continue development. Once upon a time a manager - team leader started trying to write code (he was a programmer in some other projects - not the best, but he felt like he was one). He started because one of the developers suggested an idea at the team meeting and he felt he just needed to do it on his own. He failed, and he told the dev team about it. The dev team did what he failed to do in a few days. After that, the manager feels that team codes with out him perfectly and gets the job done in short time. He felt sorry and lost and he started to crash like an old bad PC. Firstly, he started to scream (in forms of messages not in voice) he tried to tell developers that what they were doing was a bad, not-needed thing - developers kindly told him that his "beginnings" were not compilable while dev team product worked as needed. He told the developers that all work they do should be firstly discussed with him. Here is the part where we need to mention that all team members are "project owners" and logically have equal rights. The team leader suggested to the developers these options: change their dev process to go through him, or be moved from project owners to contributers. So what are our options as developers? What arguments we can provide to the team leader/manager for him to calm down? Is it possible to save the project or is it better to fork out now? An important issue is that lately we had no active ticket system, and I personally think that this was the reason the mess appeared. So... any ideas?

  Read the article

• Mounting of UDF Bluray in Linux Mint 17

  - by user134885

  I am running Linux mint 17 Cinnamon 64 Bit 2.2.13 - 3.13.0-27 Kernal My machine is a Clevo - fitted with a bluray burner I have tried the following line sudo mount -t udf /dev/scd0 /media/bluray /dev/sr0 But to no avail. Can anyone help me with how to initiate / mount a Bluray on my machine? Thank you to anyone who can give me feedback may sanity and get it going - all works well in windows, but nothing in Linux?

  Read the article

< Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >