Search Results

Search found 2650 results on 106 pages for 'robin green'.

Page 81/106 | < Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• apache on Cent OS opening default page on https

  - by Asghar

  I am new to apache and SSL and configuration, i got verysign certificte to secure my site. i have public, private and ca_intermediate cert files. i have configured ssl.conf as below VirtualHost _default_:443> DocumentRoot /var/www/mydomain.com/web/ ServerName mydomain.com:443 ServerAlias www.mydomain.com # Use separate log files for the SSL virtual host; note that LogLevel # is not inherited from httpd.conf. ErrorLog logs/ssl_error_log TransferLog logs/ssl_access_log LogLevel warn # SSL Engine Switch: # Enable/Disable SSL for this virtual host. SSLEngine on problem is that when i access www.mydoamin.com with "HTTP" it works fine, but when i access using "HTTPS" it just opens apache default page. but with green "HTTPS" means my certificates are installed correctly. How can i get rid of this situtaion. Thanks EDIT Output of apachectl -S -bash-3.2# apachectl -S [Mon Aug 27 10:20:19 2012] [warn] NameVirtualHost 82.56.29.189:80 has no VirtualHosts [Mon Aug 27 10:20:19 2012] [warn] NameVirtualHost 82.56.29.189:443 has no VirtualHosts VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: _default_:8081 localhost.localdomain (/etc/httpd/conf/sites-enabled/000-apps.vhost:10) *:8080 is a NameVirtualHost default server localhost.localdomain (/etc/httpd/conf/sites-enabled/000-ispconfig.vhost:10) port 8080 namevhost localhost.localdomain (/etc/httpd/conf/sites-enabled/000-ispconfig.vhost:10) *:443 is a NameVirtualHost default server mydomain.com (/etc/httpd/conf.d/ssl.conf:81) port 443 namevhost mydomain.com (/etc/httpd/conf.d/ssl.conf:81) *:80 is a NameVirtualHost default server app.mydomain.com (/etc/httpd/conf/sites-enabled/100-app.mydomain.com.vhost:7) port 80 namevhost app.mydomain.com (/etc/httpd/conf/sites-enabled/100-app.mydomain.com.vhost:7) port 80 namevhost mydomain.com (/etc/httpd/conf/sites-enabled/100-mydomain.com.vhost:7) Syntax OK

  Read the article

• Recovering a mdadm+lvm+ext4 partition with read error

  - by bitwelder

  One of disks in my NAS has failed. The NAS is running Linux, and it uses mdadm + LVM technology for its filesystems. I do have backup for most of the contents, but not for the very last changes, and if possible, I'd like to recover that from this failing disk. The disk (a 'green drive' WD10EARS 1TB in size) throws this kind of errors: Oct 3 12:00:41 kernel: [ 3625.620000] ata5.00: read unc at 9453282 Oct 3 12:00:41 kernel: [ 3625.620000] lba 9453282 start 9453280 end 1953511007 Oct 3 12:00:41 kernel: [ 3625.620000] sde5 auto_remap 0 Oct 3 12:00:41 kernel: [ 3625.630000] ata5.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 Oct 3 12:00:41 kernel: [ 3625.630000] ata5.00: edma_err_cause=00000084 pp_flags=00000003, dev error, EDMA self-disable Oct 3 12:00:41 kernel: [ 3625.640000] ata5.00: failed command: READ FPDMA QUEUED Oct 3 12:00:41 kernel: [ 3625.650000] ata5.00: cmd 60/40:00:e0:3e:90/00:00:00:00:00/40 tag 0 ncq 32768 in Oct 3 12:00:41 kernel: [ 3625.650000] res 41/40:00:e2:3e:90/12:00:00:00:00/40 Emask 0x409 (media error) <F> Oct 3 12:00:41 kernel: [ 3625.660000] ata5.00: status: { DRDY ERR } However, while testing with 'dd', I noticed that if I skip the first 4kB, the read seems to be ok, i.e. a command like. dd if=/dev/sde5 of=dev/null bs=4k count=1000 skip=1 doesn't return any read error. Supposing that there is no other read failure in the rest of the disk, would I be able to recover this 900 GB partition (as I mentioned before, it's a 'linux raid autodetect' partition, that contains a a LVM2 volume that contains a ext4 filesystem) if I copy-clone the partition somewhere else, but the first 4kB?

  Read the article

• Suddenly can't send E-Mails with Apple Mail to Gmail SMTP

  - by slhck

  Hi all, I have a weird problem that started just today. I am using Apple Mail on a Leopard machine, connecting to Gmail. Fetching e-mail works just fine. My SMTP settings are also correct. Still, I can't send mail, it will display a pop up saying that "transferring the content to the mail server" failed (translation from German, could be different in English OS X versions). I have verified the following: My SMTP settings are definitely correct. I have not changed them and the issue appeared today. Also, I went through the Apple online configuration for Gmail accounts and did not have to adjust any setting. I can run network diagnosis and it will connect to both POP and SMTP servers without a problem (all green lights) The Telnet details will show me the HELO message from the Gmail servers, so there's no authentication failure. Console.app will not show any messages related to "mail" when I try to send the mail, so there's no specific error message The mail I'm trying to send does not have an attachment, it is plaintext only I can login to gmail.com and send mails without a problem The recipient address exists and contains no syntax errors I can also not send mails to myself When using another IP and ISP (through VPN), it still doesn't work As for my settings: I connect to smtp.gmail.com and for advanced settings I choose password-based authentication with user: [email protected] and my password. I let Apple Mail try the default ports (for SSL and TLS, respectively). Again: I have not changed a thing between yesterday and today. What is causing that strange behavior? Any help would be much appreciated.

  Read the article

• Dell PowerEdge 860 won't boot but gets power

  - by fierflash

  I have a Dell PowerEdge 860. Got an 2008 R2 running on it. Here is the scenario I'm currently in: I can boot it up and work as usuall. But when I restart it, it just shuts down, doesn't reboot, and it won't boot up again. Then it stays in this "mode", On/off button blinking green(standby mode?) and System Indicator LED blinking amber. If I try to press the On/Off button on the frontpanel it won't boot. It's like you can hear the fan from the PSU running but nothing else is trying to boot. If I unplug the powercable and then put it back in again it's the same, the extremley noisy fans won't start and it's just sitting there. If I let it "rest" for like 1 to 24 hours while the powercable is unplugged and I plug it in again, it boots directly, without me having to push the On/Off button. What I have tried: Run diagnostics(not the one in POST phase) and everything is fine Booting without any cables except the powercable Boot without memory installed Boot without the raidcable plugged in Cleared NVRAM Reseated all the components and cables Googling like a freak for any possible solution Tried Dell Support but I don't have any warranty left so they can't help me unless i pay some ridiculous amount of money I suppos Do anyone have some experience with the same issue? Do I need to replace something or is there any other way to determine the problem? Any help will be greatly appreciated.

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• What's wrong with this vcl config for varnish-cache as load balancer?

  - by dabito

  I have the current configurations active on my default.vcl varnish file on the machine that balances the load for other two machines (the other two machines also have varnish active). My intention is to have this server do only the load balancing and the other machines do the processing and also their own caching. My problem is that even with the config testing (not even a stress test or anything, just a few requests a minute) I get the guru meditation error and have to restart varnish. This is the default.vcl for the load balancing server: backend vader { .host = "app1.server.com"; .probe = { .url = "/"; .interval = 10s; .timeout = 4s; .window = 5; .threshold = 3; } } backend malgus { .host = "app2.server.com"; .probe = { .url = "/"; .interval = 10s; .timeout = 4s; .window = 5; .threshold = 3; } } director dooku round-robin { { .backend = vader; } { .backend = malgus; } } sub vcl_recv { if (req.http.host ~ "^balancer.server.com$") { set req.backend = dooku; } } Am I doing something wrong or missing something? EDIT: This is varnishlog's output: 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345839995 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345839998 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345840001 1.0 0 Backend_health - malgus Still sick 4--X--- 0 3 5 0.000000 3.846876 0 Backend_health - vader Still sick 4--X--- 0 3 5 0.000000 3.839194 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1345840004 1.0 14 SessionOpen c 10.150.7.151 38272 :80 14 ReqStart c 10.150.7.151 38272 458200540 14 RxRequest c GET 14 RxURL c / 14 RxProtocol c HTTP/1.1 14 RxHeader c Host: dooku-dev.excelsior.com 14 RxHeader c Connection: keep-alive 14 RxHeader c User-Agent: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 14 RxHeader c Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 14 RxHeader c Accept-Encoding: gzip,deflate,sdch 14 RxHeader c Accept-Language: en-US,en;q=0.8,es-419;q=0.6,es;q=0.4 14 RxHeader c Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 14 RxHeader c Cookie: SESSa87d6c6da0c61037a9169122dc5e4a19=HR_0Srhgc-uDArT3aJFzOBy31FtzneTXg38byr1eGMU; __atuvc=4%7C33 14 VCL_call c recv pass 14 VCL_call c hash 14 Hash c / 14 Hash c dooku-dev.excelsior.com 14 VCL_return c hash 14 VCL_call c pass pass 14 FetchError c no backend connection 14 VCL_call c error deliver 14 VCL_call c deliver deliver 14 TxProtocol c HTTP/1.1 14 TxStatus c 503 14 TxResponse c Service Unavailable 14 TxHeader c Server: Varnish 14 TxHeader c Content-Type: text/html; charset=utf-8 14 TxHeader c Retry-After: 5 14 TxHeader c Content-Length: 418 14 TxHeader c Accept-Ranges: bytes 14 TxHeader c Date: Fri, 24 Aug 2012 20:26:44 GMT 14 TxHeader c X-Varnish: 458200540 14 TxHeader c Age: 0 14 TxHeader c Via: 1.1 varnish 14 TxHeader c Connection: close 14 Length c 418 14 ReqEnd c 458200540 1345840004.916415691 1345840004.965190172 0.020933390 0.048741817 0.000032663 14 SessionClose c error 14 StatSess c 10.150.7.151 38272 0 1 1 0 1 0 256 418 14 SessionOpen c 10.150.7.151 38273 :80 14 ReqStart c 10.150.7.151 38273 458200541 14 RxRequest c GET 14 RxURL c /favicon.ico 14 RxProtocol c HTTP/1.1 14 RxHeader c Host: dooku-dev.excelsior.com 14 RxHeader c Connection: keep-alive 14 RxHeader c Accept: */* 14 RxHeader c User-Agent: Mozilla/5.0 (X11; Linux x86_64) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 14 RxHeader c Accept-Encoding: gzip,deflate,sdch 14 RxHeader c Accept-Language: en-US,en;q=0.8,es-419;q=0.6,es;q=0.4 14 RxHeader c Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 14 RxHeader c Cookie: SESSa87d6c6da0c61037a9169122dc5e4a19=HR_0Srhgc-uDArT3aJFzOBy31FtzneTXg38byr1eGMU; __atuvc=4%7C33 14 VCL_call c recv pass 14 VCL_call c hash 14 Hash c /favicon.ico 14 Hash c dooku-dev.excelsior.com 14 VCL_return c hash 14 VCL_call c pass pass 14 FetchError c no backend connection 14 VCL_call c error deliver 14 VCL_call c deliver deliver 14 TxProtocol c HTTP/1.1 14 TxStatus c 503 14 TxResponse c Service Unavailable 14 TxHeader c Server: Varnish 14 TxHeader c Content-Type: text/html; charset=utf-8 14 TxHeader c Retry-After: 5 14 TxHeader c Content-Length: 418 14 TxHeader c Accept-Ranges: bytes 14 TxHeader c Date: Fri, 24 Aug 2012 20:26:45 GMT 14 TxHeader c X-Varnish: 458200541 14 TxHeader c Age: 0 14 TxHeader c Via: 1.1 varnish 14 TxHeader c Connection: close 14 Length c 418 14 ReqEnd c 458200541 1345840005.226389885 1345840005.226457834 0.000026941 0.000043154 0.000024796 14 SessionClose c error 14 StatSess c 10.150.7.151 38273 0 1 1 0 1 0 256 418

  Read the article

• How can I remotely display images on my computer?

  - by Jakob

  What I Have: A laptop booted with Ubuntu and a stationary computer dual-booted with Ubuntu and Vista, both connected through a wireless ad-hoc network. What I Want: I want a way to display images in fullscreen on my stationary, using my laptop as a "remote control". I want to be able to choose another picture at any time and have my stationary computer remain in fullscreen mode at all times. Preferably, I should also be able to display just an empty (black) screen. How can I arrange for this? What I Have Tried: I have tried simply SSH:ing into my stationary computer and opening the image files using an image viewer, but all of the ones that I have tried (Eye of Gnome, Mirage, Gwenview, and others) open a new window for every new image. I don't know how to force them into using a single instance. I have tried using the VLC remote control command line interface, but apart from seeming somewhat unreliable (exiting with segmentation faults at one point), it also displays some images with a green border and forces me to pause playback in order for the image to remain on screen. Bonus Question: In my final setup, I also need to play music through my stationary computer's speaker and have the ability to switch to another track at any point, like with the images. Preferably, I would like to control the images and the audio through the same interface. How can I best achieve this?

  Read the article

• How to get data from a borked Windows Home Server

  - by harhoo

  Yesterday we had a power surge, followed by a power outage. This left my WHS borked: powering on just gives to a flashing blue light (the led on the power supply also flashes green) - no fan or boot activity, nothing. I urgently needed some files off there in the short term (and the 500GB of photos, music, personal video etc in the long term) so I took the hard drive out and put it in my computer. The files and folders showed up, but I couldn't access them - clicking on an image gave an invalid image error in Picasa, I couldn't play MP3s etc. I changed the ownership and permissions of the files, still nothing. I booted in with a LiveCD, the same: files appear, but won't open. Is there anything else I can do? I'm now wondering if it was just the power cable that's broken, but if so, why can;t I access my files from the hard drive? If it is the power cable, and I replace that and the hard drive, will I have done any harm messing around with ownership and file permissions?

  Read the article

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• Windows 7 ICS client web failure

  - by n8wrl

  I have several windows 7 PC's connected on a LAN via a hub. One has a Verizon 3G connection and works great. I have internet connection sharing enabled on it, which automagically set the LAN connection to 192.168.137.1 and enabled DHCP. I am trying to get the client PC's working one at a time. The others are off. The client is able to: Get an IP via DHCP with correct settings. Ping any web address I can throw at it, so DNS and routing are working. Windows update works. But web sites hang in IE. All but google.com! I type www.msn.com, microsoft.com, amazon.com, etc. etc. All ping via a cmd window but IE just hangs - it says web site found but the green progress bar just slowly creeps and no content displays. www.google.com comes up even after clearing browser and dns cache. I am pulling my hair out - what am I missing? EDIT: After some more gyrations with a router I'm back to ICS. Same symptoms, only now I have an answer to Andrew's question, YES I can do Google searches but clicking on any of the result links hangs! Let one sit for half an hour with no timeout or error.

  Read the article

• How to import a text file into powershell and email it, formatted as HTML

  - by Don

  I'm trying to get a list of all Exchange accounts, format them in descending order from largest mailbox and put that data into an email in HTML format to email to myself. So far I can get the data, push it to a text file as well as create an email and send to myself. I just can't seem to get it all put together. I've been trying to use ConvertTo-Html but it just seems to return data via email like "pageFooterEntry" and "Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo" versus the actual data. I can get it to send me the right data if i don't tell it to ConvertTo-Html, just have it pipe the data to a text file and pull from it, but it's all ran together with no formatting. I don't need to save the file, i'd just like to run the command, get the data, put it in HTML and mail it to myself. Here's what I have currently: #Connects to Database and returns information on all users, organized by Total Item Size, User $body = Get-MailboxStatistics -database "Mailbox Database 0846468905" | where {$_.ObjectClass -eq “Mailbox”} | Sort-Object TotalItemSize -Descending | ft @{label=”User”;expression={$_.DisplayName}},@{label=”Total Size (MB)”;expression={$_.TotalItemSize.Value.ToMB()}} -auto | ConvertTo-Html #Pause for 5 seconds for Exchange write-host -foregroundcolor Green "Pausing for 5 seconds for Exchange" Start-Sleep -s 5 $toemail = "[email protected]" # Emails report to this address. $fromemail = "[email protected]" #Emails from this address. $server = "Exchange.company.com" #Exchange server - SMTP. #Email the report. $email = New-Object System.Net.Mail.MailMessage $email.IsBodyHtml = $True $email.To.Add($toemail) $email.From = $fromemail $email.Subject = "Exchange Mailbox Sizes" $email.Body = $body $client = New-Object System.Net.Mail.SmtpClient $server $client.UseDefaultCredentials = $true $client.Send($email) Any thoughts would be helpful, thanks!

  Read the article

• Graphics Artifacts/ Texture Flickering

  - by Cerin

  Hey I been having some problems with artifacts in games. Sometimes textures flicker. Artifacts of various shapes and sizes show up usually after a couple games of dota 2. I built my computer almost exactly one month ago and it has been doing this pretty much from the start except before the artifacts I believe just flashed on screen fast enough to where I couldn't tell what it was but I still noticed. In dota I've seen green triangular artifacts among other things. I've tried running Furmark for a while but even though it pushes the gpu much harder than dota 2, there are still no artifacts. It maxes in furmark at about 60C and running every game I've tried on it at 40C. CPU and system temp don't usually get higher than 40C either. These are my system specs: Gigabyte Z68 Intel Motherboard 16 GB Gskill Ripjaws SDRAM DDR3 Sapphire Radeon HD 7770 GHz edition Intel Core i5-2500k (with built in gpu) Corsair 750 Watt PSU windows 7-64 bit I have the latest drivers for everything. What should I do about this? Try to RMA my graphics card? Are there other things that could be causing this?

  Read the article

• Suggestions for Backup solution

  - by jiewmeng

  i am considering between windows home server simple nas extra HDD's in desktop btw, i will be the main user i am looking to fulfil the following needs: reliability (i am think RAID 1 or 5) not so prone to virus/malware infections (will using a separate NAS or home server help? say windows home server is still a windows pc except separated by network?) power efficiency (eg. spin down when not in use) download (eg. i may want to dl big files/torrents overnight and i may not want to use a full powered PC for it? does a full pc vs NAS provide significant power usage to justify cost of new system esp. since i am only user?) performance (i guess i like to write/access my files fast, on 2nd thought, maybe for backup i can forgo this? maybe for a WD Green HDD? but how much slower will it be? plus since i am the only user, i think the whole HDD will be mine?)

  Read the article

• Tortoise SVN, find all non-added files?

  - by John Isaacks

  I am using Tortoise SVN on Windows. I have a deep directory structure (using cakephp). After creating several files I then went through and +added them. The new files show a ? next to them and a + next to them after set to add so it is easy to tell which files still need to be added. this is the same with folders. However if a new file is inside an old folder there will still be the green checkmark. You won't have any indicator telling you there is a new file. So I forgot to add one before a commit. This wouldn't be so bad as I could just add it and recommit. However, I also made this a tag, so I had recommit to the tag and the trunk. Anyways this wouldn't have been an issue if there was an indicator on existing folders that contain new files. Is there a way to set this up?

  Read the article

• Windows 7 - All Icons Missing, Explorer Progress Bar Never Finishes, Libraries Gone

  - by Alex

  since yesterday i've had three issues which all arose at the same time. windows 7 x64, i7 2.8ghz 12gb ddr3 1 - my libraries, favorites, drives are missing...basically the entire sidebar is gone. http://i.imgur.com/m8pRQ.png. yet when i open a dialog, my libraries and drives are back to normal ONLY for the dialog. i tried Restore Default Libraries. it works one time, but when i open libraries again i go back to the empty mess. restarting the computer temporarily fixes the problem. 2 - in the explorer window that's showing libraries, when i navigate to a certain folder i get an unending progress bar (the kind that turns the address bar green). yesterday when the problem started, i was saving a file to this folder. the program writing the file crashed during the write and i believe that's what caused the problem. i have sugarsync backing up that folder and when i restarted the computer sugarsync informed me that its database was corrupted, so i had to uninstall and reinstall the software. 3 - icons are missing. the Rebuild Icon Cache did not fix this. http://i.imgur.com/r9pgo.png restarting the computer temporarily fixes these problems, but when i open the directory with the initial write problem, everything stops working. edit: i should note that i did a chkdsk /f and it repaired problems. i also did the thing that verifies then restores windows files (can't remember the command now), which reported that everything was normal.

  Read the article

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• Use autocomplete in dropdown cells with Excel 2007?

  - by Martin

  I want to make a survey with Excel and I therefore have defined the cells for the answers as a dropdown cell which only accepts answers from a certain list, e. g.: The two Lists List1 and List2 (yellow cells) are the possible answers for the questions in Block 1.x resp. 2.x (blue) . There might be a block 4 with more questions, which again use List1 for their possible answers. My problem is: I'd like to be able to use the autocompleate feature to fill in the blue cells with the dropdown menu, so that the user only types 5 and it automatically expands to "5: extremely important" or "5: extremely difficult". According to my research on the www, this should be possible if I add the list with possible answers directly above the cells where autocomplete should work (I did this with the green helper cells which could be hidden) . But I have to enter at least 4 characters 5: e to get the autocompleted suggestion. Is there a way to make autocomplete already replace a "5" by the corresponding valid term? As the survey file shall be distributed to a lot of people "outside", I can not use VBA magic because it may be blocked on their computer and might not work. EDIT: it seems to have to do with the numbers I use: If I'd start my List items with A, B, C instead of 1, 2, 3, it would work perfectly. Excel seems to ignore the pure numbers when they are entered and does not try to autocomplete them.. is there a workaround? (I hope it is clear what I want, it seems a little difficult to explain.)

  Read the article

• Can we do a DNSSEC 101? [closed]

  - by PAStheLoD

  Please share your opinions, FAQs, HOWTOs, best practices (or links to the one you think is the best) and your fears and thoughts about the whole migration (or should I just call it a new piece of tech?). Is DNSSEC just for DNS providers (name server operators)? What ought John Doe to do, who hosts johndoe.com at some random provider (GoDaddy, DreamHost and such)? Also, what if the provider's name server doesn't do automatic signing magic, can John do it manually? In a fire-and-forget way, without touching KSKs and ZSKs rollovers and updating and headaches?) Does it bring any change regarding CERT records? Do browsers support it? How come it became so complex? Why didn't they just merged it with SSL? DKIM is pretty straightforward, IANA/IETF could've opted for something like that. (Yes I know that creating a trust anchor would be still problematic, but browsers are already full of CA certs. So, they could've just let anyone get a cert for a domain for shiny green padlocks, or just generate one for a poor blue lock, put it into a TXT record, encrypt the other records and let the parent zone sign the whole for you with its cert.) Thanks! And for disclosure (it seemed like the customary thing to do around here), I've asked the same on the netsec subreddit.

  Read the article

• Need advice in setting up server. fastCGI, suExec, speed, security, etc.

  - by lewisqic

  I am running my own dedicated server with centOS 5 and WHM/cPanel. I would like to configure my server to meet my needs but I need a little help. It will only be my own websites being run on this server. I'm still a little green when it comes to server administration so please forgive my ignorance. What I Would Like to Have: I need some public directories to be writable (for user image uploads and things like that) but I don't want those directories to have 777 permissions. I need individual accounts to have the ability to set custom php settings for their own account without affecting other accounts, whether through a php.ini file or through .htaccess or any other method. I would like things to run as fast as possible, whether that means using a php optimizer or cacher, such as eaccelerator or xcache or anything else. I need things to be as secure as possible. Here Are My Questions What should I use for my php handler? DSO? CGI? fastCGI? suPHP? Other? Should I be using suEXEC? What are the benefits or downfalls of this? What php optimizer/cacher is best to use? Are there any other security tips I need to know about all of this? I'd appreciate any advice or direction that can be offered. Thanks!

  Read the article

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• How to determine if my AWS/EC2 server has been compromised / resolution?

  - by ElHaix

  I have recently seen an increase in network in/out activity on my server and am trying to determine if my AWS/EC2 instance has been compromised, and if so, how to resolve? In my security group I have: Inbound: 80 (HTTP) 0.0.0.0/0 Outbound: 80 (HTTP) 0.0.0.0/0 443 (HTTPS) 0.0.0.0/0 Using TCP-UDP Endpoint Viewer: I see a lot of w3wp.exe TCP processes with varying local ports http and numbered, as well as varying remote ports. Some processes go red/yellow/green on updates . I see Remote address for most w3wp processes are my ec2 instance, however I am seeing several to *.deploy.akamaitechnologies.com and *.deploy.static.akamaitechnologies.com with received bytes varying between 4-11 megs. I also see Ec2Config.exe, remote address: 169.254.169.254 System Process Remote Address: fetcher4-4.p.mail.ru (how can I get rid of this one?!) local port: http remote port: 33432 I am also seeing some system processes from 114.216-244-93-rdns.wowrack.com: Protocol: TCP local port: http remote port: varying As well as some baiduspider "System Process"'s. I'm afraid that my system may have been compromised, and wondering if these results are any indication of that. If so, how can I get eliminate these possible threats? I have MS Security Essentials installed.

  Read the article

• Microphone doesn't work

  - by mandy

  I'm having a trouble with my built in microphone. Even if I use headphone with mic, it doesn't really work. The weird thing is, if I clap the green lines of the speaker icon jumps, but if I speak it doesn't. I have also tried some recordings, but I can not hear myself and adjusting the volume didn't help at all. I tried to restore it, still no change. I have updated it in the device manager, but it said there that it's up to date and the devices are working properly. Until I decided to recover the whole system (wherein I pressed zero and switch on button) to my surprise, the settings became different, most programs were deleted, even my files. It's like it was formatted and I'm so sad that the mic was not fixed. I really don't know what to do now. My laptop model is Toshiba satellite m840. I want to it return to its settings/set up just before I Recover the system and bring back all the programs that we're installed and of course, most of all, to fix my microphone so I can use Skype again and other video calling application.. I hope someone could help me. Thanks a lot!

  Read the article

• Problem with connecting two different networks

  - by tanascius

  I have two networks: 192.168.13.0/24 (blue) and 192.168.15.0/24 (green). Computer A is connected to the 13-net, only. Computer B has two interfaces, one in each network. There is third computer that acts like a router and connects the 13-net to the 15-net (only in this direction). Now, I'd like to ping 192.168.15.100 from computer A to B. Unfortunately there is never a reply. But when I use a hub instead of a switch it works. In my opinion the ping packet travels through the switch to the router (which is the default route/gateway for A). The router sends the packet back to the switch to B. Probably B receives it on its 15-net interface but answers with it's 15th interface? Is this possible? The problem is, that B may have only a gateway 192.168.13.50 - but I am not really sure of it (B is a embedded system with limited configuration possibilities). Can anyone explain what happens here? Thank you!

  Read the article

< Previous Page | 77 78 79 80 81 82 83 84 85 86 87 88  | Next Page >