Search Results

Search found 6387 results on 256 pages for 'cpu allocation'.

Page 82/256 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• What free space thresholds/limits are advisable for 640 GB and 2 TB hard disk drives with ZEVO ZFS on OS X?

  - by Graham Perrin

  Assuming that free space advice for ZEVO will not differ from advice for other modern implementations of ZFS … Question Please, what percentages or amounts of free space are advisable for hard disk drives of the following sizes? 640 GB 2 TB Thoughts A standard answer for modern implementations of ZFS might be "no more than 96 percent full". However if apply that to (say) a single-disk 640 GB dataset where some of the files most commonly used (by VirtualBox) are larger than 15 GB each, then I guess that blocks for those files will become sub optimally spread across the platters with around 26 GB free. I read that in most cases, fragmentation and defragmentation should not be a concern with ZFS. Sill, I like the mental picture of most fragments of a large .vdi in reasonably close proximity to each other. (Do features of ZFS make that wish for proximity too old-fashioned?) Side note: there might arise the question of how to optimise performance after a threshold is 'broken'. If it arises, I'll keep it separate. Background On a 640 GB StoreJet Transcend (product ID 0x2329) in the past I probably went beyond an advisable threshold. Currently the largest file is around 17 GB –  – and I doubt that any .vdi or other file on this disk will grow beyond 40 GB. (Ignore the purple masses, those are bundles of 8 MB band files.) Without HFS Plus: the thresholds of twenty, ten and five percent that I associate with Mobile Time Machine file system need not apply. I currently use ZEVO Community Edition 1.1.1 with Mountain Lion, OS X 10.8.2, but I'd like answers to be not too version-specific. References, chronological order ZFS Block Allocation (Jeff Bonwick's Blog) (2006-11-04) Space Maps (Jeff Bonwick's Blog) (2007-09-13) Doubling Exchange Performance (Bizarre ! Vous avez dit Bizarre ?) (2010-03-11) … So to solve this problem, what went in 2010/Q1 software release is multifold. The most important thing is: we increased the threshold at which we switched from 'first fit' (go fast) to 'best fit' (pack tight) from 70% full to 96% full. With TB drives, each slab is at least 5GB and 4% is still 200MB plenty of space and no need to do anything radical before that. This gave us the biggest bang. Second, instead of trying to reuse the same primary slabs until it failed an allocation we decided to stop giving the primary slab this preferential threatment as soon as the biggest allocation that could be satisfied by a slab was down to 128K (metaslab_df_alloc_threshold). At that point we were ready to switch to another slab that had more free space. We also decided to reduce the SMO bonus. Before, a slab that was 50% empty was preferred over slabs that had never been used. In order to foster more write aggregation, we reduced the threshold to 33% empty. This means that a random write workload now spread to more slabs where each one will have larger amount of free space leading to more write aggregation. Finally we also saw that slab loading was contributing to lower performance and implemented a slab prefetch mechanism to reduce down time associated with that operation. The conjunction of all these changes lead to 50% improved OLTP and 70% reduced variability from run to run … OLTP Improvements in Sun Storage 7000 2010.Q1 (Performance Profiles) (2010-03-11) Alasdair on Everything » ZFS runs really slowly when free disk usage goes above 80% (2010-07-18) where commentary includes: … OpenSolaris has changed this in onnv revision 11146 … [CFT] Improved ZFS metaslab code (faster write speed) (2010-08-22)

  Read the article

• apache eats up too much ram per child

  - by mrc4r7m4n

  Hello to everyone. I've got fallowing problem: Apache eat to many ram per child. The fallowing comments shows: cat /etc/redhat-release -- Fedora release 8 (Werewolf) free -m: total used free shared buffers cached Mem: 3566 3136 429 0 339 1907 -/+ buffers/cache: 889 2676 Swap: 4322 0 4322 I know that you will say that there is nothing to worry about because swap is not use, but i think it's not use for now. 3.httpd -v: Server version: Apache/2.2.14 (Unix) 4.httpd -l: Compiled in modules: core.c mod_authn_file.c mod_authn_default.c mod_authz_host.c mod_authz_groupfile.c mod_authz_user.c mod_authz_default.c mod_auth_basic.c mod_include.c mod_filter.c mod_log_config.c mod_env.c mod_setenvif.c mod_version.c mod_ssl.c prefork.c http_core.c mod_mime.c mod_status.c mod_autoindex.c mod_asis.c mod_cgi.c mod_negotiation.c mod_dir.c mod_actions.c mod_userdir.c mod_alias.c mod_rewrite.c mod_so.c 5.List of loaded dynamic modules: LoadModule authz_host_module modules/mod_authz_host.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule alias_module modules/mod_alias.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule cgi_module modules/mod_cgi.so 6.My prefrok directive <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 25 ServerLimit 80 MaxClients 80 MaxRequestsPerChild 4000 </IfModule> KeepAliveTimeout 6 MaxKeepAliveRequests 100 KeepAlive On 7.top -u apache: ctrl+ M top - 09:19:42 up 2 days, 19 min, 2 users, load average: 0.85, 0.87, 0.80 Tasks: 113 total, 1 running, 112 sleeping, 0 stopped, 0 zombie Cpu(s): 7.3%us, 15.7%sy, 0.0%ni, 75.7%id, 0.0%wa, 0.7%hi, 0.7%si, 0.0%st Mem: 3652120k total, 3149964k used, 502156k free, 348048k buffers Swap: 4425896k total, 0k used, 4425896k free, 1944952k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 16956 apache 20 0 700m 135m 100m S 0.0 3.8 2:16.78 httpd 16953 apache 20 0 565m 130m 96m S 0.0 3.7 1:57.26 httpd 16957 apache 20 0 587m 129m 102m S 0.0 3.6 1:47.41 httpd 16955 apache 20 0 567m 126m 93m S 0.0 3.6 1:43.60 httpd 17494 apache 20 0 626m 125m 96m S 0.0 3.5 1:58.77 httpd 17515 apache 20 0 540m 120m 88m S 0.0 3.4 1:45.57 httpd 17516 apache 20 0 573m 120m 88m S 0.0 3.4 1:50.51 httpd 16954 apache 20 0 551m 120m 88m S 0.0 3.4 1:52.47 httpd 17493 apache 20 0 586m 120m 94m S 0.0 3.4 1:51.02 httpd 17279 apache 20 0 568m 117m 87m S 16.0 3.3 1:51.87 httpd 17302 apache 20 0 560m 116m 90m S 0.3 3.3 1:59.06 httpd 17495 apache 20 0 551m 116m 89m S 0.0 3.3 1:47.51 httpd 17277 apache 20 0 476m 114m 81m S 0.0 3.2 1:37.14 httpd 30097 apache 20 0 536m 113m 83m S 0.0 3.2 1:47.38 httpd 30112 apache 20 0 530m 112m 81m S 0.0 3.2 1:40.15 httpd 17513 apache 20 0 516m 112m 85m S 0.0 3.1 1:43.92 httpd 16958 apache 20 0 554m 111m 82m S 0.0 3.1 1:44.18 httpd 1617 apache 20 0 487m 111m 85m S 0.0 3.1 1:31.67 httpd 16952 apache 20 0 461m 107m 75m S 0.0 3.0 1:13.71 httpd 16951 apache 20 0 462m 103m 76m S 0.0 2.9 1:28.05 httpd 17278 apache 20 0 497m 103m 76m S 0.0 2.9 1:31.25 httpd 17403 apache 20 0 537m 102m 79m S 0.0 2.9 1:52.24 httpd 25081 apache 20 0 412m 101m 70m S 0.0 2.8 1:01.74 httpd I guess thats all information needed to help me solve this problem. I think the virt memory is to big, the same res. The consumption of ram is increasing all the time. Maybe it's memory leak because i see there is so many static modules compiled. Could someone help me with this issue? Thank you in advance. 8.ldd /usr/sbin/httpd linux-gate.so.1 => (0x0012d000) libm.so.6 => /lib/libm.so.6 (0x0012e000) libpcre.so.0 => /lib/libpcre.so.0 (0x00157000) libselinux.so.1 => /lib/libselinux.so.1 (0x0017f000) libaprutil-1.so.0 => /usr/lib/libaprutil-1.so.0 (0x0019a000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x001b4000) libldap-2.3.so.0 => /usr/lib/libldap-2.3.so.0 (0x001e6000) liblber-2.3.so.0 => /usr/lib/liblber-2.3.so.0 (0x00220000) libdb-4.6.so => /lib/libdb-4.6.so (0x0022e000) libexpat.so.1 => /lib/libexpat.so.1 (0x00370000) libapr-1.so.0 => /usr/lib/libapr-1.so.0 (0x00391000) libpthread.so.0 => /lib/libpthread.so.0 (0x003b9000) libdl.so.2 => /lib/libdl.so.2 (0x003d2000) libc.so.6 => /lib/libc.so.6 (0x003d7000) /lib/ld-linux.so.2 (0x00110000) libuuid.so.1 => /lib/libuuid.so.1 (0x00530000) libresolv.so.2 => /lib/libresolv.so.2 (0x00534000) libsasl2.so.2 => /usr/lib/libsasl2.so.2 (0x00548000) libssl.so.6 => /lib/libssl.so.6 (0x00561000) libcrypto.so.6 => /lib/libcrypto.so.6 (0x005a6000) libgssapi_krb5.so.2 => /usr/lib/libgssapi_krb5.so.2 (0x006d9000) libkrb5.so.3 => /usr/lib/libkrb5.so.3 (0x00707000) libcom_err.so.2 => /lib/libcom_err.so.2 (0x0079a000) libk5crypto.so.3 => /usr/lib/libk5crypto.so.3 (0x0079d000) libz.so.1 => /lib/libz.so.1 (0x007c3000) libkrb5support.so.0 => /usr/lib/libkrb5support.so.0 (0x007d6000) libkeyutils.so.1 => /lib/libkeyutils.so.1 (0x007df000) Currently i cant restart the apache. I work in a company and now there is rush hours. I will do that about 5 pm. Current top -u apache: shift + M top - 12:31:33 up 2 days, 3:30, 1 user, load average: 0.73, 0.80, 0.79 Tasks: 114 total, 1 running, 113 sleeping, 0 stopped, 0 zombie Cpu(s): 3.3%us, 4.7%sy, 0.0%ni, 90.0%id, 1.3%wa, 0.3%hi, 0.3%si, 0.0%st Mem: 3652120k total, 3169720k used, 482400k free, 353372k buffers Swap: 4425896k total, 0k used, 4425896k free, 1978688k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 16957 apache 20 0 708m 145m 117m S 0.0 4.1 2:11.32 httpd 16956 apache 20 0 754m 142m 107m S 0.0 4.0 2:33.94 httpd 16955 apache 20 0 641m 136m 103m S 5.3 3.8 1:58.37 httpd 17515 apache 20 0 624m 131m 99m S 0.0 3.7 2:03.90 httpd 16954 apache 20 0 627m 130m 98m S 0.0 3.6 2:13.87 httpd 17302 apache 20 0 625m 124m 97m S 0.0 3.5 2:10.80 httpd 17403 apache 20 0 624m 114m 91m S 0.0 3.2 2:08.85 httpd 16952 apache 20 0 502m 114m 81m S 0.0 3.2 1:23.78 httpd 16186 apache 20 0 138m 61m 35m S 0.0 1.7 0:15.54 httpd 16169 apache 20 0 111m 49m 17m S 0.0 1.4 0:06.00 httpd 16190 apache 20 0 126m 48m 24m S 0.0 1.4 0:11.44 httpd 16191 apache 20 0 109m 48m 19m S 0.0 1.4 0:04.62 httpd 16163 apache 20 0 114m 48m 21m S 0.0 1.4 0:09.60 httpd 16183 apache 20 0 127m 48m 23m S 0.0 1.3 0:11.23 httpd 16189 apache 20 0 109m 47m 17m S 0.0 1.3 0:04.55 httpd 16201 apache 20 0 106m 47m 17m S 0.0 1.3 0:03.90 httpd 16193 apache 20 0 103m 46m 20m S 0.0 1.3 0:10.76 httpd 16188 apache 20 0 107m 45m 18m S 0.0 1.3 0:04.85 httpd 16168 apache 20 0 103m 44m 17m S 0.0 1.2 0:05.61 httpd 16187 apache 20 0 118m 41m 21m S 0.0 1.2 0:08.50 httpd 16184 apache 20 0 111m 41m 19m S 0.0 1.2 0:09.28 httpd 16206 apache 20 0 110m 41m 20m S 0.0 1.2 0:11.69 httpd 16199 apache 20 0 108m 40m 17m S 0.0 1.1 0:07.76 httpd 16166 apache 20 0 104m 37m 18m S 0.0 1.0 0:04.31 httpd 16185 apache 20 0 99.3m 36m 16m S 0.0 1.0 0:04.16 httpd as you can see the memory usage growing up from e.g. res( 135 to 145)m and it will be growing up till memory ends. Are you sure that this option i set up: <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 25 ServerLimit 80 MaxClients 80 MaxRequestsPerChild 4000 </IfModule> KeepAliveTimeout 6 MaxKeepAliveRequests 100 KeepAlive On are correct? Maybe i should decrease some of them? Another questions that bother me: I got e.g. static module mod_negotiation.c compiled into apache and the same module loaded as dynamic. Is this normal that i've loaded duplicated module. But when i want to remove dynamic module(mod_negotiation.c) from httpd.conf and then restart apache error appears. Now I cant tell this error message because i cant restart apache :( Hello again:) This is memory usage just after restart apache: top - 16:19:12 up 2 days, 7:18, 3 users, load average: 1.08, 0.91, 0.91 Tasks: 109 total, 2 running, 107 sleeping, 0 stopped, 0 zombie Cpu(s): 17.0%us, 25.7%sy, 51.0%ni, 4.7%id, 0.0%wa, 0.3%hi, 1.3%si, 0.0%st Mem: 3652120k total, 2762516k used, 889604k free, 361552k buffers Swap: 4425896k total, 0k used, 4425896k free, 2020980k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 13569 apache 20 0 93416 43m 15m S 0.0 1.2 0:02.55 httpd 13575 apache 20 0 98356 38m 16m S 32.3 1.1 0:02.55 httpd 13571 apache 20 0 86808 33m 12m S 0.0 0.9 0:02.60 httpd 13568 apache 20 0 86760 33m 12m S 0.0 0.9 0:00.81 httpd 13570 apache 20 0 83480 33m 12m S 0.0 0.9 0:00.51 httpd 13572 apache 20 0 63520 5916 1548 S 0.0 0.2 0:00.02 httpd 13573 apache 20 0 63520 5916 1548 S 0.0 0.2 0:00.02 httpd 13574 apache 20 0 63520 5916 1548 S 0.0 0.2 0:00.02 httpd 13761 apache 20 0 63388 5128 860 S 0.0 0.1 0:00.01 httpd 13762 apache 20 0 63388 5128 860 S 0.0 0.1 0:00.01 httpd 13763 apache 20 0 63388 5128 860 S 0.0 0.1 0:00.00 httpd I will try to compile apache from source to newest version. Thx for help guys.

  Read the article

• BIOS interrupts, priviledge levels and paging

  - by Jack

  Hi, I was learning about Intel 8086-80486 CPUs and their interactions with HW. But I still don´t understand it quite well. Please, help me fill blank spots. First, I know that CPU communicates with HW using BIOS interrupts. But, what really happens in PC, when I call some INT instruction? I know that according the interrupt table some instructions begin to execute, but how by executing some instructions can BIOS recognize what I want to do? Becouse as far as I know, CPU has no extra communication channel with BIOS, it can only adress memory and receive data. So how can I instruct BIOS to do something, when I can only adress RAM? Next thing I dont understand is about priviledge levels. I know about ring model, and acess rights, but how CPU knows which priviledge level has executed instruction? I think that these priviledges apply only when intruction is trying to adress memory, but how applications gets its priviledge level? I mean I know its level 3, but how its set? And last thing, I know that paging is adress scheme that is used to support aplication-transparent virtual memory, or swaping, but I could not find any informations about how is paging tied with protected mode. Like if paging is like next mode independent of protectet mode, or its somehow implemented within protected mode. And if it is implemented in protected mode, isn´t it too slow, to first adress application space, than offset, and than paging folder, page and offset once again? Thank you for every response.

  Read the article

• Linux AMD-FX 8350 temperature monitoring

  - by HyperDevil

  I’m trying to get the CPU temperature for my AMD-FX8350 on Debian Squeeze. I ran sensors-detect and then sensors, but I only get my motherboard sensors (it8720-isa-0228). There are three temperature values there but I assume those are not for the CPU. it8720-isa-0228 Adapter: ISA adapter in0: +1.36 V (min = +0.00 V, max = +4.08 V) in1: +1.50 V (min = +0.00 V, max = +4.08 V) in2: +3.38 V (min = +0.00 V, max = +4.08 V) in3: +2.93 V (min = +0.00 V, max = +4.08 V) in4: +3.07 V (min = +0.00 V, max = +4.08 V) in5: +4.08 V (min = +0.00 V, max = +4.08 V) in6: +4.08 V (min = +0.00 V, max = +4.08 V) in7: +2.93 V (min = +0.00 V, max = +4.08 V) Vbat: +3.01 V fan1: 3375 RPM (min = 10 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 1730 RPM (min = 10 RPM) fan5: 0 RPM (min = 0 RPM) temp1: +27.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor temp2: +53.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode temp3: +65.0°C (low = +127.0°C, high = +90.0°C) sensor = thermal diode cpu0_vid: +0.000 V Is there anything I am missing? I also loaded the K8temp and K10temp modules and ran sensor-detect without any results. I do see this message in dmesg: hwmon-vid: Unknown VRM version of your x86 CPU

  Read the article

• Sun Solaris - Find out number of processors and cores

  - by Adrian

  Our SPARC server is running Sun Solaris 10; I would like to find out the actual number of processors and the number of cores for each processor. The output of psrinfo and prtdiag is ambiguous: $psrinfo -v Status of virtual processor 0 as of: dd/mm/yyyy hh:mm:ss on-line since dd/mm/yyyy hh:mm:ss. The sparcv9 processor operates at 1592 MHz, and has a sparcv9 floating point processor. Status of virtual processor 1 as of: dd/mm/yyyy hh:mm:ss on-line since dd/mm/yyyy hh:mm:ss. The sparcv9 processor operates at 1592 MHz, and has a sparcv9 floating point processor. Status of virtual processor 2 as of: dd/mm/yyyy hh:mm:ss on-line since dd/mm/yyyy hh:mm:ss. The sparcv9 processor operates at 1592 MHz, and has a sparcv9 floating point processor. Status of virtual processor 3 as of: dd/mm/yyyy hh:mm:ss on-line since dd/mm/yyyy hh:mm:ss. The sparcv9 processor operates at 1592 MHz, and has a sparcv9 floating point processor. _ $prtdiag -v System Configuration: Sun Microsystems sun4u Sun Fire V445 System clock frequency: 199 MHZ Memory size: 32GB ==================================== CPUs ==================================== E$ CPU CPU CPU Freq Size Implementation Mask Status Location --- -------- ---------- --------------------- ----- ------ -------- 0 1592 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 on-line MB/C0/P0 1 1592 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 on-line MB/C1/P0 2 1592 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 on-line MB/C2/P0 3 1592 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 on-line MB/C3/P0 _ $more /etc/release Solaris 10 8/07 s10s_u4wos_12b SPARC Copyright 2007 Sun Microsystems, Inc. All Rights Reserved. Use is subject to license terms. Assembled 16 August 2007 Patch Cluster - EIS 29/01/08(v3.1.5) What other methods can I use? EDITED: It looks like we have a 4 processor system with one core each: $psrinfo -p 4 _ $psrinfo -pv The physical processor has 1 virtual processor (0) UltraSPARC-IIIi (portid 0 impl 0x16 ver 0x34 clock 1592 MHz) The physical processor has 1 virtual processor (1) UltraSPARC-IIIi (portid 1 impl 0x16 ver 0x34 clock 1592 MHz) The physical processor has 1 virtual processor (2) UltraSPARC-IIIi (portid 2 impl 0x16 ver 0x34 clock 1592 MHz) The physical processor has 1 virtual processor (3) UltraSPARC-IIIi (portid 3 impl 0x16 ver 0x34 clock 1592 MHz)

  Read the article

• Auto load balancing two node Cluster Hyper-v 2008 R2 enterprise?

  - by Kristofer O

  My setup is a 2 node cluster with 72GB ram each and a ~10TB MD3000i Iscsi SAN. I have about 30VMs running I keep about 15 on either server. I do a live migration to the other server if I need to run updates or whatever... Either one of the servers is able of running all VM if needed, but the cpu is pretty high. Here's my issues. I know Hyper-v has a limit of a single Live-migration at a time. But Why doesn't it queue them up to move one at a time? If I multi select I don't get the option to live migrate a one at a time. OR if I'm in the process of Migrating one it will give me an error that it's currently migrating a VM... Is there a button I missed that will tell a Node that it needs to migrate all the VMs elsewhere? Another question, does anyone know whats the best way to load balance VMs based on CPU and/or network utilzation. I have some VMs that don't do much. and some that trash the CPU or network. I'd like to balance it out on both servers if at all possible. and Is there any way to automate it? last question... If I overcommit my Cluster is there a way to tell the cluster that I want certian VMs the be running and to savestate other VMs based on availible system resources? Say when my one node blue screens and the other node begins starting the VMs up. I want the unimportant ones to shutdown or savestate so the important ones can stay running or come back online. Thanks just for reading all that. Any help would be great.

  Read the article

• Htpc aka "Media Center": cheap and *silent*?

  - by Unknown

  It may be me, or the place I live (Italy), but it seems pretty hard to get a build or a prebuilt nettop or a laptop that fits the need. I need something silent able to playback all h.264 fullhd content without stuttering, and well (and not loosing the hw acceleration because of softsubs...) silent not ugly silent and (possibly) cheap. I'm going the linux route, therefore i'm moving towards a cpu-based or nvida-integrated solution (i don't think ati hw accelerated playback - or the intel "hd" acceleration - is useable yet). Ion nettop; it's either the Acer Revo (but here it's incredibly pricey and it's hard to find the dualcore version) or the Asrock Ion 330, that in the current version is rated "silent" at 26Db. 26. Sounds pretty noisy to me!!! the previous version was even worse. was this product really aimed at htpc market?? the Dell Zino - i think it's ATI based unfortunately. Laptop: correct me if I'm wrong: sub 600€/$ units are quite loud under full load (because of the tiny fans). ULW laptops are indeed quite similar: tiniest fans = high pitched noise and the cpu still lacks power for non hd-accelerated video decoding Handmade build: little money can be saved with underpowered cpus, a low-midrange cpu would help in the case of non-hw-accelerated content the cases are quite pricey the PSU one has to get ranges between 100/150 €/$ minimum to keep the noise down a low-mid build, all included, sums up to over 650 €/$ for a still-looking-ugly-unit, without the blu-ray drive. Please help. What do you advise on this? ;) Am I ignoring laptops too much, maybe? Are low-priced Acers that noisy/high pitched under full load?

  Read the article

• Problems with freetype on OSX 10.7.4

  - by eythor

  I'm trying to install mplayer with OSD using homebrew. I've added both --enable-menu and --with-freetype-config=/usr/local/Cellar/freetype/2.4.10/freetype-config to the brew recipe. ==> Downloading http://www.mplayerhq.hu/MPlayer/releases/MPlayer-1.1.tar.xz Already downloaded: /Library/Caches/Homebrew/mplayer-1.1.tar.xz xz -dc "/Library/Caches/Homebrew/mplayer-1.1.tar.xz" | /usr/bin/tar xf - ==> ./configure --prefix=/usr/local/Cellar/mplayer/1.1 --cc=cc --host-cc=cc --disable-cdparanoia --disable-libopenjpeg --enable-menu --disable-x11 -- with-freetype-config=/usr/local/Cellar/freetype/2.4.10/freetype-config ./configure --prefix=/usr/local/Cellar/mplayer/1.1 --cc=cc --host-cc=cc --disable-cdparanoia --disable-libopenjpeg --enable-menu --disable-x11 --with -freetype-config=/usr/local/Cellar/freetype/2.4.10/freetype-config Checking for cc version ... clang 4.2.1 (experimental support only) Checking for working compiler ... yes Detected operating system: Darwin Detected host architecture: x86_64 Checking for cross compilation ... no Checking for host cc ... cc Checking for CPU vendor ... GenuineIntel (6:15:10) Checking for CPU type ... Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz For freetype-config I've tried three seperate paths; /usr/X11R6/bin/freetype-config, /usr/X11/bin/freetype-config and the one in Cellar. Checking for freetype always fails: Checking for freetype >= 2.0.9 ... no Checking for fontconfig ... no (FreeType support needed) Although freetype itself seems to be installed. mufasa:bin eythor$ freetype-config --version 15.0.9 mufasa:bin eythor$ freetype-config --ftversion 2.4.10 mufasa:bin eythor$ freetype-config --libs -L/usr/local/Cellar/freetype/2.4.10/lib -lfreetype -lz -lbz2 mufasa:bin eythor$ freetype-config --cflags -I/usr/local/Cellar/freetype/2.4.10/include/freetype2 - I/usr/local/Cellar/freetype/2.4.10/include I'm not sure what to try next or how to figure out why freetype isn't recognized. Can anyone point me in a sensible direction?

  Read the article

• How to improve Windows Server 2008 R2 to handle many connections?

  - by invisal

  It has been a few days so far that I am trying to figure how to solve this problem. First of all, I am running a website with an average daily page view of 350,000. Previously, all ads management (tracking click and impression that each ads has served) and content were served in a single server with the following spec: Server 1 OS: Windows 2008 R2 64-Bit CPU: Intel® Core™ i5 - 4 cores RAM: 8 GB Storage: 2 x 1 TB hard drives Bandwidth: 10 TB per month To improve our website speed, I decided to separate the ads management script to another dedicated server because we have more than 15 advertisers to 30 advertisers per each page. Server 2 OS: Windows 2008 R2 64-Bit CPU: Intel® Core™ i5 - 4 cores RAM: 4 GB Storage: 2 x 300 GB hard drives Bandwidth: 10 TB per month The Problem The problem is that Server 1 can handle both content and ads system. Now, that I take away the ads system and put it at Server 2. Server 2 can barely serve only ads system. Test First of all, I moved 75% of the ads to Server 2. And then, perform a ping to server: ping -t xxxxx. [I did the ping for 10 minutes and its following similar pattern as below] Reply from xxxxx bytes=32 time=290ms TTL=116 Reply from xxxxx bytes=32 time=289ms TTL=116 Reply from xxxxx bytes=32 time=320ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Reply from xxxxx bytes=32 time=348ms TTL=116 Reply from xxxxx bytes=32 time=284ms TTL=116 Then, I moved 100% of the ads to Server 2. Then, perform a ping to server again. [I did the ping for 10 minutes and its following similar pattern as below] Reply from xxxxx bytes=32 time=290ms TTL=116 Request timed out Reply from xxxxx bytes=32 time=320ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Request timed out Request timed out Reply from xxxxx bytes=32 time=284ms TTL=116 Attempts Increase MaxUserPort and TcpNumConnection Restart the server Increase IIS Max Instances and Instance MaxRequests Server Resource Only 10%-15% of the network connection is used Only 10%-15% of the CPU is used Only 25% of the memory is used

  Read the article

• Why is my Compaq NC8430 laptop so darned HOT ?

  - by Cheeso

  For a long time I've had a Compaq nc8430 laptop. It's nearly 3 years old now. Originally shipped with WinXP, but I installed Vista on it. From the very start it was not a good experience. This thing has one of those "stickpoint" mice, which I like. After a while, I noticed that the computer was generating lots and lots of heat. So much heat, that the stickpoint bumper would melt and disintegrate. Normally I would expect heat if the CPU was working hard, but even when the CPU was idle, the computer was hot. Much too hot to keep on my lap. Turns out this is not an uncommon problem. I installed the HWmonitor tool, and found that the CPU temp was 82C when it was plugged in - pretty darn hot. And because the temp was so high, the fan never turned off, so the laptop was as loud as a jet engine, always. If I unplugged it from A/C power, the screen would dim and the temperature would decrease, and the fan noise would lessen, but still, it was too loud. It's totally unusable. What is the problem?

  Read the article

• System fans connected to a Gigabyte Z77-D3H motherboard do not increase in speed

  - by Andrew

  The motherboard (Gigabyte Z77-D3H) controls my 3-pin CPU fan just fine. My system fans are a 3-pin fan (plugged into SYS_FAN1), and a 4-pin fan plugged into SYS_FAN3. All 3 of the system fan headers are 4-pin, but the user manual states that SYS_FAN1 is really a 3-pin header (that it can control the speed of a 3-pin fan) and the 4th pin is just a reserve. All my fans have a max RPM of 2000. Normally, all the fans run around 1000 RPMs when I'm not doing anything intensive. This proves that the motherboard can set the speed. However,when I run Folding@Home and my temperatures increase (around 70C) only the CPU fan increases to around 2000 RPMs. The system fans stay around 1000 RPMs. Through the BIOS I am able to disable the system fan control and the system fans then run at max RPMs (meaning the motherboard was doing something). I've updated the BIOS to the latest version and tried out Speedfan, but neither helped my situation. What I'd like is for the system fans to ramp up their RPMs as needed. Any thoughts? Tl;dr: My system (case) fans, but not my CPU fan, are always stuck around 1000 RPMs out of 2000 no matter the temperature.

  Read the article

• sql server 2008 cluster hang when a heavy load is run

  - by Billy OT

  we have a sql server 2008 active/active cluster running on wondows 2008R2 O/S. 14GB RAM, 4xCPU. we have set a ceiling of 12GB for sql server. We're running an agent job which loads 3 million records to a database. during this load the job fails and the cluster seems to attempt to fail over to the other node but unsuccessfully i.e., the cluster address is no longer accessible. we have to manually fail the cluster node back. during the load on viewing task manager we can see that memory usage hits a max of 12.5GB and CPU at times hits 100% on all 4 CPU, but for the most part fluctuates at an average of about 60%. I suppose my question is, will a cluster try to fail over if memory or CPU are taking a heavy hit? or am i barking up the wrong tree? also any ideas why it wouldn't fully fail over? we've crawled through logs, of which there are a lot, and can't find anything useful. we've also tried recreating the issue but it ran successfully at a later time. Also 3 million rows doesn't seem like a lot but in terms of resources should 14GB RAM and 4xCPU not be sufficient? Further information on this, we ran the load again today and corrupted the database! We received the error message : LogWriter: Operating system error 170. It looks like, under the heavy load, the sql cluster attempted to fail over and in doing so migrated a lun (or drive) which meant the disk was no longer reachable. (this is just our theory). The database is now 'suspect' and requiring restoration. The 170 error above also indicates that on failing over to the other node, the sql service could not start as it was already in use, therefore it couldn't fail over fully?? But I'm wondering why would it need to fail over in the first place? My assumptions could be completely wrong on this, so any ideas would be appreciated.

  Read the article

• Officially announced RAM support size doesn't apply to one of twin rigs with just one difference

  - by Deniz

  It'll take a little long to describe my situation but here goes the story : In January 2009 we bought (the OEM parts) two similar systems with just one difference. One of them had a Phenom X4 cpu and the other one (mine) a Phenom X3 cpu. At the beginning we had problems with both systems to power them on whilst having all of their ram slots being full. We decided to install the systems with just 2 slots populated and later try to install the rest of ram sticks. Both systems did succeed to support 3 sticks. We tried many different procedures to make the systems work with their fourth ram slots being populated. We waited for new bios updates and flashed the boards when they were available, we tried different ram sticks with different frequencies etc. One day while we were trying to install the fourth stick, the X4 machine did accept it. The other one did not. The most mind boggling thing was that after one of my trials the X3 system begun to not operate with the third slot populated. Our boards did have AMD 770 chipsets and we even tried to change the board of the X3 machine with another 770 chipset board. Now my questions are : Should we change the cpu ? What is causing the X3 system to not accept the fourth (or now the third) ram stick ? The manufacturers sites do claim that this boards do accept 4 ram sticks (but they only tested them with certain ram brands and models). What are the limitations for maximum ram configurations on motherboards ? Are there some "rules of thumb" except frequency, voltage, chip type considerations for which we did check our parts ? Our boards are : Gigabyte GA-MA770-DS3 Sapphire PC-AM2RX780 - PURE CrossFireX 770

  Read the article

• PostgreSQL lots of large Arrays and Writes

  - by strife911

  Hi, I am running a python program that spawns 8 threads and as each thread launch its own postmaster process via psycopg2. This is to maximize the use of my CPU-cores (8). Each thread call a series of SQL Functions. Most of these functions go through many thousands of rows each associated to a large FLOAT8[] Array (250-300) values by using unnest() and multiplying each FLOAT8 by an another FLOAT8 associated to each row. This Array approach minimized the size of the Indexes and the Tables. The Function ends with an Insert into another Table of a row of the same form (pk INT4, array FLOAT8[]). Some SQL Functions called by python will Update a row of these kind of Tables (with large Arrays). Now I currently have configured PostgreSQL to use most of the memory for cache (effective_cache_size of 57 GB I think) and only a small amount of it for shared memory (1GB I think). First, I was wondering what the difference between Cache and Shared memory was in regards to PostgreSQL (and my application). What I have noticed is that only about 20-40% of my total CPU processing power is used during the most Read intensive parts of the application (Select unnest(array) etc). So secondly, I was wondering what I could do to improve this so that 100% of the CPU is used. Based on my observations, it does not seem to have anything to do with python or its GIL. Thanks

  Read the article

• Will disabling hyperthreading improve performance on our SQL Server install

  - by Sam Saffron

  Related to: Current wisdom on SQL Server and Hyperthreading Recently we upgraded our Windows 2008 R2 database server from an X5470 to a X5560. The theory is both CPUs have very similar performance, if anything the X5560 is slightly faster. However, SQL Server 2008 R2 performance has been pretty bad over the last day or so and CPU usage has been pretty high. Page life expectancy is massive, we are getting almost 100% cache hit for the pages, so memory is not a problem. When I ran: SELECT * FROM sys.dm_os_wait_stats order by signal_wait_time_ms desc I got: wait_type waiting_tasks_count wait_time_ms max_wait_time_ms signal_wait_time_ms ------------------------------------------------------------ -------------------- -------------------- -------------------- -------------------- XE_TIMER_EVENT 115166 2799125790 30165 2799125065 REQUEST_FOR_DEADLOCK_SEARCH 559393 2799053973 5180 2799053973 SOS_SCHEDULER_YIELD 152289883 189948844 960 189756877 CXPACKET 234638389 2383701040 141334 118796827 SLEEP_TASK 170743505 1525669557 1406 76485386 LATCH_EX 97301008 810738519 1107 55093884 LOGMGR_QUEUE 16525384 2798527632 20751319 4083713 WRITELOG 16850119 18328365 1193 2367880 PAGELATCH_EX 13254618 8524515 11263 1670113 ASYNC_NETWORK_IO 23954146 6981220 7110 1475699 (10 row(s) affected) I also ran -- Isolate top waits for server instance since last restart or statistics clear WITH Waits AS ( SELECT wait_type, wait_time_ms / 1000. AS [wait_time_s], 100. * wait_time_ms / SUM(wait_time_ms) OVER() AS [pct], ROW_NUMBER() OVER(ORDER BY wait_time_ms DESC) AS [rn] FROM sys.dm_os_wait_stats WHERE wait_type NOT IN ('CLR_SEMAPHORE','LAZYWRITER_SLEEP','RESOURCE_QUEUE', 'SLEEP_TASK','SLEEP_SYSTEMTASK','SQLTRACE_BUFFER_FLUSH','WAITFOR','LOGMGR_QUEUE', 'CHECKPOINT_QUEUE','REQUEST_FOR_DEADLOCK_SEARCH','XE_TIMER_EVENT','BROKER_TO_FLUSH', 'BROKER_TASK_STOP','CLR_MANUAL_EVENT','CLR_AUTO_EVENT','DISPATCHER_QUEUE_SEMAPHORE', 'FT_IFTS_SCHEDULER_IDLE_WAIT','XE_DISPATCHER_WAIT', 'XE_DISPATCHER_JOIN')) SELECT W1.wait_type, CAST(W1.wait_time_s AS DECIMAL(12, 2)) AS wait_time_s, CAST(W1.pct AS DECIMAL(12, 2)) AS pct, CAST(SUM(W2.pct) AS DECIMAL(12, 2)) AS running_pct FROM Waits AS W1 INNER JOIN Waits AS W2 ON W2.rn <= W1.rn GROUP BY W1.rn, W1.wait_type, W1.wait_time_s, W1.pct HAVING SUM(W2.pct) - W1.pct < 95; -- percentage threshold And got wait_type wait_time_s pct running_pct CXPACKET 554821.66 65.82 65.82 LATCH_EX 184123.16 21.84 87.66 SOS_SCHEDULER_YIELD 37541.17 4.45 92.11 PAGEIOLATCH_SH 19018.53 2.26 94.37 FT_IFTSHC_MUTEX 14306.05 1.70 96.07 That shows huge amounts of time synchronizing queries involving parallelism (high CXPACKET). Additionally, anecdotally many of these problem queries are being executed on multiple cores (we have no MAXDOP hints anywhere in our code) The server has not been under load for more than a day or so. We are experiencing a large amount of variance with query executions, typically many queries appear to be slower that they were on our previous DB server and CPU is really high. Will disabling Hyperthreading help at reducing our CPU usage and increase throughput?

  Read the article

• Request bursting from web application Load Tests

  - by MaseBase

  I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

  Read the article

• High load without explanation

  - by Sebastian

  I have a very high load on my machine and don't know what is responsible or how to find out. On the machine runs a jboss appserver and mysql. Here is a top from the user at peak time: top - 16:23:01 up 101 days, 6:50, 1 user, load average: 23.42, 21.53, 24.73 Tasks: 9 total, 1 running, 8 sleeping, 0 stopped, 0 zombie Cpu(s): 17.2%us, 1.6%sy, 0.0%ni, 80.4%id, 0.1%wa, 0.1%hi, 0.7%si, 0.0%st Mem: 16440784k total, 16263720k used, 177064k free, 151916k buffers Swap: 16780872k total, 30428k used, 16750444k free, 8963648k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 27344 b 40 0 16.0g 6.5g 14m S 169 41.7 1184:09 java 6047 b 40 0 11484 1232 1228 S 0 0.0 0:00.01 mysqld_safe 6192 b 40 0 604m 182m 4696 S 0 1.1 93:30.40 mysqld 7948 b 40 0 84036 1968 1176 S 0 0.0 0:00.07 sshd 7949 b 40 0 14004 2900 1608 S 0 0.0 0:00.03 bash 7975 b 40 0 8604 1044 840 S 0 0.0 0:00.44 top The CPU usage of the java process is normal. The peaks only show up when i deployed a certain web application. Could the resulting network traffic boost the load in such way that i don't see it in top?

  Read the article

• Intel Atom overheating in ASUS EEE Box 1501P

  - by Sergey L.

  I have had an ASUS EEE Box 1501P for just a little bit over a year. Of course it breaks 2 months after the warranty runs out. http://www.asus.com/Eee/EeeBox_PC/EeeBox_PC_EB1501P/ I have been using the box as a Home Media Center. Running mostly 24/7 often pausing a video overnight. Since last week the fan started running extremely loud. After some digging I found that the Intel Atom CPU in it is overheating and the built-in sensor is reporting temperatures way over 105°C. This got me worried, so I took the unit apart. Completely vacuumed the heat sink, oiled the fan, but the unit is still showing the same behaviour. After turning it on and just observing the hardware monitor in the BIOS the temperature slowly rises from 40°C to over 95°C in appx 5 min. I am running the newest BIOS and a lightweight Linux OPENELEC OS with XBMC on it. Now I am wondering if it could be a faulty heat sensor in the Atom. Recommended running temperature is up to 85°C, but I have not detected any performance hits when running at the above mentioned 105°C and there seem to be no software faults. How can an Atom with an attached heat sink and a fan running at full capacity even get this hot in the first place at 0 load? Aren't those things designed to generate virtually no heat? Could it be a faulty heat sensor? What shall I try to fix this? I would prefer not to damage the CPU, since it is hard fused into the motherboard and cannot be replaced. I could remove the heat pipe/heat sink, but it is getting hot, so heat is properly transferring from the CPU to the heat pipe, the fan is running at full capacity, is recently oiled and warm air is making it out of the exhaust. Edit: One more note: The North-bridge (or whatever it is called nowadays) is on the same heat pipe.

  Read the article

• Resource Monitor (resmon) in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

  Read the article

• Tomcat performing terribly for no apparent reason

  - by John

  We're running a game application .WAR on Tomcat 6 on an Amazon EC2 server, 8 core processor, 7gb RAM. The application uses a MySQL database hosted on Amazon RDS. This Facebook application takes ages to access when a mere 20-30 users are playing it. Big difference from 1-2 users. The entire .WAR is ~4mb, all static content hosted elsewhere. The server has never been close to running out of RAM. The CPU utilization has never been higher than 13.5-14%. Even with ~500 users that completely slowed everything to a standstill. The thread count or threadpools isn't close to being maxed out. I heightened maxthreads but it didn't make a noticeable difference. My theory is that Tomcat can only use one processor core, which would explain why it was slowed to a halt even though CPU usage was stably at 13-14% at the activity spike. But I'm struggling to understand why it would only use one CPU core. There is no processor cap in server.xml. The app contains several servlets (4 or 5). There is no mention of SingleThreadModel in the Java code. WHAT could be causing the application to run extremely slowly? If there is only 1-5 people on the application it runs fine. With 20-30 people it's barely contactable.

  Read the article

• Hyper-V 2008 R2 synthetic networking stops working with linux 2.6.32.15

  - by luxifer

  Hi there, so I thought I'd give Hyper-V on Windows Server 2008 R2 Enterprise a try on my Homeserver (yes, it's legit... got it from msdnaa). First thing to throw at it was my firewall which runs IPFire. This distribution currently uses the kernel version 2.6.32.15 and comes with the Hyper-V drivers. So I enabled them and at first they work just fine but after a few minutes they just fail. There are no packages going in or out anymore until I reboot the VM but sometimes even that won't work so the VM just keeps "Stopping" like forever. Emulated networking works fine but it slow and uses more CPU. That way my firewall routes slower than when running under virtualbox on an atom N270. My server has an E6750; VM is limited to 25%, but that should still outperform this atom CPU especially since it's never going anywhere near 100% CPU load, so give me a break! A quick google search led me to people having the same problem (even with other distributions and kernel versions that include those drivers) but no solution yet... I already found this but I can't quite follow the author on the part where he solved the issue - especially since I need two virtual nics for my firewall distro to work (obviously one internal and one external) What am I missing here?

  Read the article

• ESX Scheduler and NUMA issue

  - by babyg_wc

  On our 24 core bl685 (4sockets x 6core), we find that NUMA nodes 0 and 1 are pretty busy (unfortunately resulting in elevated cpu ready times on the VMS), whilst NUMA nodes 2 and 3 are almost unused. I thought this just maybe a ESX4 U1 issue, so I had a colleague with a 32 core (dl785) farm investigate, and it seems that his last 3 or 4 NUMA nodes are also not really being utilised. ESX seems to have a weakness when it comes to balancing lightly loaded NUMA boxes, Im going to enabled node interleaving in the BIOS and see if the scheduler balancers across all 24 cores, instead of just 12!... For those of you with large core counts, I would suggest you fire up you viclient, and check Physical CPU useage (or esxtop), I would be interested to hear what your results are. Please note, that its only the lightly loaded (eg less than 30% cpu load on the esx host) that seems to have the biggest issue with load imbalance. Thoughts/comments. PS ive logged a SR with vmware to assist, also the other "problem" could be that we have 128gb of ram in each host, and therefore the scheduler sees no good reason why it shouldnt try and cram all vms's into the first two NUMA nodes, as we only have around 50gb of ram worth of vms on each host...

  Read the article

• My desktop has started overheating -- how hot is hot?

  - by Jerry

  I have a two year old desktop, some random quad core HP desktop. It used to run very quietly, but in the past month, the fans start up anytime anything "serious" is being done -- compiles, playing video, etc. Right now, speedfan and speccy report the cores are between 50C and 70C. Speedfan reports this as hot. (Nice flame icon.) Well, the system does sit on my carpet, so two weeks ago, I took off the lid, and cough *cough* it was pretty filled with dust. I got out an air can, turned on a vacuum and carefully got out all the dust that I saw on the CPU fan the case fans any fan I saw (graphics board) and blew out all the dust I could from all the circuit boards. And then I closed the case back up. It has definitely run cooler since then, but it still runs hot, and I hear high speed fan noise I never heard before. How hot is too hot? At what temps do consumer grade CPUs die? What should I be looking to do? Replace CPU fan? (It seems to work) Replace power supply fan? Assuming the dust problem is gone, where should I be looking to determine why the machine is heating up? Epilogue: After following the various pieces of advice given here, the system did run cooler, but it was still noticeably running louder (hotter) than just a few months prior. I ended up purchasing a new cpu heatsink and fan and during installation found the cooling grease from the original heatsink was just a dried, cracked layer, probably more of an insulator than heat transfer agent. With the new fan AND the new heatsink compound, the system ran much much cooler and the fan rarely turns on.

  Read the article

• Does AMD Cool n Quiet Slow Down Your System?

  - by Software Monkey

  I discovered today that having AMD Cool n Quiet enabled in my BIOS appears to be slowing down my Windows XP SP2 system by about 29% on memory & CPU intensive workloads. I was wondering if (a) anyone else had encountered this, (b) anyone can offer an explanation, (c) there are any negatives I need to be aware of if I keep AMD CnQ disabled. With some superficial testing so far, I don't immediately notice any difference with CnQ off (other than the performance being what I expected from this new hardware). It seems to ramp up the CPU fan a little bit as my program maxes out 1 core, but that's the same as with CnQ on. And when I let the system idle the CPU fan slows down and the systems as quiet as a mouse (after years of 6 small fans churning like they want to go into orbit it's nice to again have a system where I can hear the HDDs seeking). Bonus question: Does CnQ cause issues with system stability? I ask because the reason I disabled it was because I have had a few freezes and 1 spontaneous reboot with my new hardware.

  Read the article

• PC won't boot after hanging during Windows 8 automatic repair [closed]

  - by Mun

  I've got a custom built PC using an ASUS P5E motherboard and Intel Q6600 CPU. I plugged in my mp3 player to the USB port yesteday, and when I came back to the machine after about an hour or so, the Windows 8 automatic repair message was on the screen. It seemed to stick there for an hour, after which I decided to just hit reset and try and figure out what was going on. However, the machine rebooted to a black screen before even getting to the BIOS, with the monitor lights just blinking indicating there was no signal. Tried powering down completely, waiting a few minutes and then powering back up again with no difference; black screen with monitor lights blinking. Tried leaving it on for a while and then pinging from another machine or accessing it via something like LogMeIn, but everything showed the machine as being offline. There were also no error beeps or anything like that. Also tried unplugging all of the memory and rebooting and that also caused no error beeps. Removed one of the display cards and left the other one in there, and still only a black screen. I'm inclined to think that the motherboard or CPU is fried, but there is no indication of damage on any components and the CPU fan seems to be working fine as it always has, so overheating seems unlikely. It's also plugged into a surge protector. The motherboard also has a green light which still lights up. As everything was still working fine before hitting the reset button during Windows 8 automatic repair screen, at which point everything stopped working, it seems unlikely that this problem is down to component failure. Has anyone else experienced anything like this or have any ideas on what could be causing this behavior?

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >