Search Results

Search found 5019 results on 201 pages for 'jakarta commons logging'.

Page 82/201 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• Wicked VNC Viewer acting out on Windows desktop and CentOS 6.3 server

  - by Johnny Lee

  What we have here is the only way to open the TightVNC viewer on this Windows XP desktop is to have a TigerVNC viewer open on the CentOS 6.3 server desktop. I know it sounds really weird and we’re looking for hints to make it go away. Any ideas? Here is the recipe: We are using Putty on the Windows desktop as SSH (Secure Shell) and a Terminal Emulator. We open and login to Putty then open a login to TightVNC viewer. After many failed attempts, much Googling, and lots of reading to no avail I decided to open the TigerVNC viewer on the CentOS 6.3 server by way of the GNOME desktop Application menu -- Internet tab. After opening and logging into the TigerVNC viewer on the CentOS 6.3 Server, Voila!! We have a remote desktop opened on the server. But what was an interesting discovery was that the TigerVNC viewer on the server had a request on the desktop that was not on the server desktop. This turned out to be a login request that once the password was entered it opened the TightVNC viewer on the Windows desktop. Weird huh? -Why is that password request showing up on the CentOS 6.3 server in the TigerVNC viewer as oppose to showing up on the Windows desktop when logging in using TightVNC viewer to the server?

  Read the article

• Getting Error while running RED5 server - class path resource [red5.xml] cannot be opened because it does not exist

  - by sunil221

  HI , I have installed java version "1.6.0_14" and Ant version 1.8.2 for red5 Server. when i am trying to run red5 server i am getting the following error please help Root: /usr/local/red5 Deploy type: bootstrap Logback selector: org.red5.logging.LoggingContextSelector Setting default logging context: default 11:27:39.838 [main] INFO org.red5.server.Launcher - Red5 Server 1.0.0 RC1 $Rev: 4171 $ (http://code.google.com/p/red5/) Red5 Server 1.0.0 RC1 $Rev: 4171 $ (http://code.google.com/p/red5/) SLF4J: Class path contains multiple SLF4J bindings. SLF4J: Found binding in [jar:file:/usr/local/red5/red5.jar!/org/slf4j/impl/StaticLoggerBinder.class] SLF4J: Found binding in [jar:file:/usr/local/red5/lib/logback-classic-0.9.26.jar!/org/slf4j/impl/StaticLoggerBinder.class] SLF4J: See http://www.slf4j.org/codes.html#multiple_bindings for an explanation. 11:27:39.994 [main] INFO o.s.c.s.FileSystemXmlApplicationContext - Refreshing org.springframework.context.support.FileSystemXmlApplicationContext@39d85f79: startup date [Mon Dec 21 11:27:39 EST 2009]; root of context hierarchy 11:27:40.149 [main] INFO o.s.b.f.xml.XmlBeanDefinitionReader - Loading XML bean definitions from class path resource [red5.xml] Exception org.springframework.beans.factory.BeanDefinitionStoreException: IOException parsing XML document from class path resource [red5.xml]; nested exception is java.io.FileNotFoundException: class path resource [red5.xml] cannot be opened because it does not exist Bootstrap complete

  Read the article

• Getting Error while running RED5 server - class path resource [red5.xml] cannot be opened because it does not exist

  - by sunil221

  HI , I have installed java version "1.6.0_14" and Ant version 1.8.2 for red5 Server. when i am trying to run red5 server i am getting the following error please help Root: /usr/local/red5 Deploy type: bootstrap Logback selector: org.red5.logging.LoggingContextSelector Setting default logging context: default 11:27:39.838 [main] INFO org.red5.server.Launcher - Red5 Server 1.0.0 RC1 $Rev: 4171 $ (http://code.google.com/p/red5/) Red5 Server 1.0.0 RC1 $Rev: 4171 $ (http://code.google.com/p/red5/) SLF4J: Class path contains multiple SLF4J bindings. SLF4J: Found binding in [jar:file:/usr/local/red5/red5.jar!/org/slf4j/impl/StaticLoggerBinder.class] SLF4J: Found binding in [jar:file:/usr/local/red5/lib/logback-classic-0.9.26.jar!/org/slf4j/impl/StaticLoggerBinder.class] SLF4J: See http://www.slf4j.org/codes.html#multiple_bindings for an explanation. 11:27:39.994 [main] INFO o.s.c.s.FileSystemXmlApplicationContext - Refreshing org.springframework.context.support.FileSystemXmlApplicationContext@39d85f79: startup date [Mon Dec 21 11:27:39 EST 2009]; root of context hierarchy 11:27:40.149 [main] INFO o.s.b.f.xml.XmlBeanDefinitionReader - Loading XML bean definitions from class path resource [red5.xml] Exception org.springframework.beans.factory.BeanDefinitionStoreException: IOException parsing XML document from class path resource [red5.xml]; nested exception is java.io.FileNotFoundException: class path resource [red5.xml] cannot be opened because it does not exist Bootstrap complete

  Read the article

• pam debugging "check pass; user unknown"

  - by lvc

  I am attempting to get Prosody authenticating with its auth_pam module. It is configured to use the pam service name xmpp. The pam.d/xmpp file is copied straight from the one configured for dovecot (originally taken from, I think, dovecot's documentation), which is known to be working: # cat /etc/pam.d/xmpp auth required pam_unix.so nullok debug account required pam_unix.so debug Logging in with dovecot works wonderfully. Logging in with prosody, with exactly the same username and password, causes Prosody to return 'Not authorized', and the following in journalctl -f: Oct 29 22:12:14 riscque.net prosody[9396]: c2s1d010b0: Client sent opening <stream:stream> to riscque.net Oct 29 22:12:14 riscque.net prosody[9396]: c2s1d010b0: Sent reply <stream:stream> to client Oct 29 22:12:14 riscque.net prosody[9396]: [178B blob data] Oct 29 22:12:14 riscque.net unix_chkpwd[9408]: check pass; user unknown Oct 29 22:12:14 riscque.net prosody[9396]: pam_unix(xmpp:auth): conversation failed Oct 29 22:12:14 riscque.net prosody[9396]: pam_unix(xmpp:auth): unable to obtain a password Oct 29 22:12:14 riscque.net prosody[9396]: pam_unix(xmpp:auth): auth could not identify password for [lvc] Oct 29 22:12:14 riscque.net prosody[9396]: riscque.net:saslauth: sasl reply: <failure xmlns='urn:ietf:params:xml:ns:xmpp-sasl'><not-authorized/><text>Unable to authorize you with the authentication credentials you&apos;ve sent.</text></failure> This series of errors seems mutually contradictory - first it says "user unknown", but then that it can't obtain the password for lvc - this username certainly exists on the system. What is likely going on here, and how would I debug this further?

  Read the article

• Missing Home Folder XP Clients 2008R2 Domain

  - by minamhere

  We just completed a migration from Server 2003 to Server 2008R2. Everything seems to have gone well except that many of our desktops have stopped mapping the Home Folder as set in Active Directory. Other mappings that are defined on individual clients are mapping just fine, these mappings are all on the same file server as the failing Home Folders. Half of the users are on 1 file server and half are on another. Users from both servers are having this problem. I have enabled the Group Policy setting to "Wait for network before logging in". I enabled the policy to "Run Logon Scripts synchronously". There are no errors on the Domain Controller or either File Server. When I enabled Group Policy Preferences as an attempted workaround, I get this error: The user 'V:' preference item in the '<Policy Name>' Group Policy object did not apply because it failed with error code '0x800708ca This network connection does not exist.' This error was suppressed. This seems to indicate that the network connection is not ready by the time Group Policy is processed. But isn't this the point of the "Wait before logging in" and "Run Logon scripts synchronously" settings? Some other background facts: The new Server 2008R2 installation is a Virtual Machine. It is on a new Subnet in a different building from the old server. DNS and DHCP were also migrated from the old DC to this new DC. These Home Folders were all working properly before the migration. Are there new security restrictions/policies in Server 2008R2 that might be causing this? Is there a way to check whether I have an underlying network connectivity issue? Maybe moving the server to the new building is causing a delay/timeout? Any thoughts or ideas on what could be causing this or how I can resolve this? Thanks.

  Read the article

• Time Machine doesn't back up some folders/files (that it should)

  - by Eric

  MacBook Pro 17" (Snow Leopard) -- WD 2TB external drive MacBook Pro 13" (Snow Leopard) -- Seagate 1TB external drive I find that Time Machine sometimes doesn't back up new folders (and the files in them). This occurs both when I choose "Back Up Now" from the Time Machine icon in the Menu Bar and in TM's scheduled backups. These are not excluded folders (nor are then in the TM do-not-back-up list); they're perfectly normal folders (at various locations) inside my home folder. The only way to force them to be backed up is to restart the computer (unmounting & mounting the TM external disk does not help). There seems to be a correlation with new folders (i.e., it's more likely to happen that an entire new folder is not backed up), but this may just be observer bias (because those are the folders that I go check to see if they've been backed up). It's not computer dependent (it happens on two different computers). It's not external disk dependent (it happens on two different external disks). It's not time dependent (not restarting for several days does not fix the problem). What does a restart change that these other events don't? I'm considering deleting the /.fseventsd folder (without restarting the computer) to see if that helps. I haven't tried logging out and logging in (without restarting the computer).

  Read the article

• auth.log is empty (Ubuntu)

  - by Vinicius Pinto

  The /var/log/auth.log file in my Ubuntu 9.04 is empty. syslogd is running and /etc/syslog.conf content is as follows. Any help? Thanks. # /etc/syslog.conf Configuration file for syslogd. # # For more information see syslog.conf(5) # manpage. # # First some standard logfiles. Log by facility. # auth,authpriv.* /var/log/auth.log *.*;auth,authpriv.none -/var/log/syslog #cron.* /var/log/cron.log daemon.* -/var/log/daemon.log kern.* -/var/log/kern.log lpr.* -/var/log/lpr.log mail.* -/var/log/mail.log user.* -/var/log/user.log # # Logging for the mail system. Split it up so that # it is easy to write scripts to parse these files. # mail.info -/var/log/mail.info mail.warning -/var/log/mail.warn mail.err /var/log/mail.err # Logging for INN news system # news.crit /var/log/news/news.crit news.err /var/log/news/news.err news.notice -/var/log/news/news.notice # # Some `catch-all' logfiles. # *.=debug;\ auth,authpriv.none;\ news.none;mail.none -/var/log/debug *.=info;*.=notice;*.=warning;\ auth,authpriv.none;\ cron,daemon.none;\ mail,news.none -/var/log/messages # # Emergencies are sent to everybody logged in. # *.emerg * # # I like to have messages displayed on the console, but only on a virtual # console I usually leave idle. # #daemon,mail.*;\ # news.=crit;news.=err;news.=notice;\ # *.=debug;*.=info;\ # *.=notice;*.=warning /dev/tty8 # The named pipe /dev/xconsole is for the `xconsole' utility. To use it, # you must invoke `xconsole' with the `-file' option: # # $ xconsole -file /dev/xconsole [...] # # NOTE: adjust the list below, or you'll go crazy if you have a reasonably # busy site.. # daemon.*;mail.*;\ news.err;\ *.=debug;*.=info;\ *.=notice;*.=warning |/dev/xconsole

  Read the article

• Apache2 - 500 internal server error

  - by Lucio Coire Galibone

  i'm running a VPS with Linux CentOs 6 with 4 GB of RAM, 10 GB of HD and 2 virtual CPU Intel(R) Xeon(R)CPU L5640 @ 2.27GHz. As my host says each virtual CPU must be at least 0.5 physical cpu. At certain times of the day, those with more traffic, trying accessing my php script i receive intermittently "500 internal server error". I activate logging to debug level from apache, and also the PHP logging with E_ALL, but I can't find reference to Error 500 in any logs(I checked the right logs!). I haven't got any .htaccess file in path script. The strange thing is that the error start at first php line in the script (the previous html displays correctly, but at the first php line the script send 500 error). The cpu load is always good (max 0.15 0.08 0.01) and RAM is close to 95% but it arrived to swap just 2 times in a month with 2-5 MB. Apache works with prefork with this values: <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 280 MaxClients 280 MaxRequestsPerChild 4000 </IfModule> Everthing works correctly and I don't get any error in quiet times, but i start receive errors when traffic rises (6-9000 visits per hour). Can i solve the problem increasing resources? (i can upgrade RAM up to 16 GB). It can depend from reaching MaxClients (but apache must write it on log, right?)? If I upgrade RAM to 6 or 8 GB i have to calculate MaxClients value with this? MaxClients = Total RAM dedicated to the web server / Max child process size Max child process size is around 20M. How else can the problem be? Thanks in advance

  Read the article

• BlazeDS first response is VERY SLOW

  - by chibban

  Hi everyone, I have a very strange an annoying problem: I have an appliaction written in Flex 3, with BlazeDS 3.2 and Java in the backend. I'm actually using a portal (liferay) to display portlets that contain Flex movies. When I hit a refresh button on my page, all the Flex movies send a RemoteObject request to the server (using BlazeDS), which should go to java classes and invoke a method (standard BlazeDS usage I 'm guessing). I'm experiencing VERY slow response (14 minutes) on the first hit, while the following hits are much faster. I've enabled the BlazeDS logging (logging level="All") and I also have debug prints coming from my java classes. I also use the "showBusyCursor" attribute for the RemoteObject - so I can see indication of the request being sent from the flex movie. Here is what I see: I hit the refresh button Each movie invokes a RemoteObject request I see a busy sign - in all the movies I see nothing in the log - no BlazeDS prints and no Java prints Wait 14 minutes or so I see BlazeDS prints followed by Java prints I see data populating my flex movies. The really weird thing is that I have the same "application" installed in 4 different computers (on my laptop and in 3 other unix machines), 3 of these installations work well (good response times) and only 1 has the issue I'm describing. I've tried many things, but everything failed. I'd be really happy to get some advice on this. Thanks

  Read the article

• Can't log in after restoring from Time Machine

  - by Jay Conrod

  My friend uses a Macbook Pro with Snow Leopard 10.6.2. She uses both FileVault and Time Machine to preserve her data. Recently, she suffered a hard disk failure. After restoring from Time Machine using the Snow Leopard install disk, she gets the following error when logging in: You are unable to log in to the FileVault user account at this time. Logging into the account failed because an error occurred. When examining the file system through Terminal, I noticed her home directory is not present: there is no /Users/username directory, or the FileVault .sparsebundle file that's supposed to be there. When using Time Machine.app on /Users, it appears as if her home directory as never there. Additionally, I did a search on the backup disk with the following command: sudo find /Volumes/backup -name '*.sparsebundle' No results. She told me that after working with some large data files, Time Machine would come on, and it would sound like it was transferring a lot of data to the hard disk. Time Machine must have been doing something, right? How can we recover her files? Are they still there?

  Read the article

• How to enable the 2 concurrent (+1 console) sessions on Windows Server 2012

  - by Dai

  I have a Windows Server 2012 VM running on Windows Azure. I want to enable the ability for 2 simultaneous administrative sessions over Remote Desktop. This is permitted under the EULA for Windows Server 2012. This is NOT the same thing as the fully-blown Terminal Services / RDS feature. In Windows Server 2000 and 2003, multiple concurrent sessions (up to a limit of 2, plus the root /console session) were enabled by default (such that logging-in via RDP without logging-out first would create a new session rather than reconnecting to the old session). In Server 2008 and later it uses single-sessions by default, as this simplifies administration (as most people want to connect to old sessions). In Windows Server 2008 R2, you can add the MMC snap-ins for Remote Desktop Host Configuration which allows you to re-enable concurrent sessions. However, in Server 2012, after adding the Remote Administration snap-ins from Server Manager it seems the Remote Desktop Host Configuration snap-in has been removed. How can I re-enable the multiple concurrent sessions for Remote Desktop for Administration in Windows Server 2012?

  Read the article

• nginx rewrite or internal redirection cycle

  - by gyre

  Im banging my head against a table trying to figure out what is causing redirection cycle in my nginx configuration when trying to access URL which does not exist Configuration goes as follows: server { listen 127.0.0.1:8080; server_name .somedomain.com; root /var/www/somedomain.com; access_log /var/log/nginx/somedomain.com-access.nginx.log; error_log /var/log/nginx/somedomain.com-error.nginx.log debug; location ~* \.php.$ { # Proxy all requests with an URI ending with .php* # (includes PHP, PHP3, PHP4, PHP5...) include /etc/nginx/fastcgi.conf; } # all other files location / { root /var/www/somedomain.com; try_files $uri $uri/ ; } error_page 404 /errors/404.html; location /errors/ { alias /var/www/errors/; } #this loads custom logging configuration which disables favicon error logging include /etc/nginx/drop.conf; } this domain is a simple STATIC HTML site just for some testing purposes. I'd expect that the error_page directive would kick in in response to PHP-FPM not being able to find given files as I have fastcgi_intercept_errors on; in http block and nave error_page set up, but I'm guessing the request fails even before that somewhere on internal redirects. Any help would be much appreciated.

  Read the article

• Haproxy not properly passing on X-Forwarded-For header

  - by JesseP

  I have backend web servers that receive requests by way of haproxy-nginx-fastcgi. The web app used to see multiple ip's coming through in the X-Forwarded-For header, chained together with commas (most original IP on the left). At some point in the recent past (just noticed, so not sure what caused it) something changed, and now I'm only seeing a single IP passed in the header to my web application. I've tried with haproxy 1.4.21 and 1.4.22 (recent upgrade) with the same behavior. Haproxy has the forwardfor header set: option forwardfor Nginx fastcgi_params config defines this header to be passed to the app: fastcgi_param HTTP_X_FORWARDED_FOR $http_x_forwarded_for; Anyone have any ideas on what might be going wrong here? EDIT: I just started logging the $http_x_forwarded_for variable in nginx logs, and nginx is only ever seeing a single IP, which shouldn't ever be the case, as we should always see our haproxy ip added in there, right? So, issue must either be in nginx handling of the variable coming in, or haproxy not building it properly. I'll keep digging... EDIT #2: I enabled request and response header logging in HAProxy, and it is not spitting anything out for X-Forwarded-For, which seems very odd: Oct 10 10:49:01 newark-lb1 haproxy[19989]: 66.87.95.74:47497 [10/Oct/2012:10:49:01.467] http service/newark2 0/0/0/16/40 301 574 - - ---- 4/4/3/0/0 0/0 {} {} "GET /2zi HTTP/1.1" O Here are the options i set for this in my frontend: mode http option httplog capture request header X-Forwarded-For len 25 capture response header X-Forwarded-For len 25 option httpclose option forwardfor EDIT #3: It really seems like haproxy is munging the header and just passing on a single one to the backend. This is fairly impacting to our production service, so if anyone has an ideas it would be greatly appreciated. I'm stumped... :(

  Read the article

• Cannot login to ISCSI Target - hangs after sending login details

  - by Frank

  I have an ISCSI target volume, to which i am trying to connect using CentOS Linux server. Everything works fine, but cannot its stuck at login. Here are the steps i am performing: [root@neon ~]# iscsiadm -m node -l iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session20 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session21 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session22 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session23 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session30 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session31 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session78 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session79 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session80 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session81 Logging in to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) After this step, its stucks, waits for some time and then gives this output: Logging in to [iface: iface1, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) iscsiadm: Could not login to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260]. My iscsi.conf is this: node.startup = automatic node.session.timeo.replacement_timeout = 15 # default 120; RedHat recommended node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 5 node.session.err_timeo.abort_timeout = 15 node.session.err_timeo.lu_reset_timeout = 20 node.session.initial_login_retry_max = 8 # default 8; Dell recommended node.session.cmds_max = 1024 # default 128; Equallogic recommended node.session.queue_depth = 32 # default 32; Equallogic recommended node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 discovery.sendtargets.iscsi.MaxRecvDataSegmentLength = 32768 node.conn[0].iscsi.HeaderDigest = None node.session.iscsi.FastAbort = Yes Also, in access control, i have given full access to Any IP, Any CHAP user and fixed iscsi initiator name. With same access level, all other volumes on rest of servers are working, except this one.

  Read the article

• Successful login with iscsiadm on target still doesn't create block device

  - by Halfgaar

  I've set up an experiment to test iscsitarget and initiator, which at some point worked. Later, I turned the setup back on and much to my dismay, the initiator machine stopped making block devices for its successful logins. As far as I know, I haven't changed anything on either machine. Some details: # iscsiadm -m node --login Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260] Logging in to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260] Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun1, portal: 10.0.0.1,3260]: successful Login to [iface: default, target: iqn.2010-12.nl.ytec.arbiter:arbiter.lun2, portal: 10.0.0.1,3260]: successful Sessions: # iscsiadm -m session tcp: [3] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun1 tcp: [4] 10.0.0.1:3260,1 iqn.2010-12.nl.ytec.arbiter:arbiter.lun2 Netstat: # netstat -n -p|grep 3260 tcp 0 0 10.0.0.2:48719 10.0.0.1:3260 ESTABLISHED 1078/iscsid tcp 0 0 10.0.0.2:48718 10.0.0.1:3260 ESTABLISHED 1078/iscsid /var/log/syslog doesn't give errors: Jan 27 11:41:49 vmnode001 kernel: [ 378.041749] scsi7 : iSCSI Initiator over TCP/IP Jan 27 11:41:49 vmnode001 kernel: [ 378.044180] scsi8 : iSCSI Initiator over TCP/IP lsscsi doesn't show my devices: [0:0:1:0] cd/dvd TSSTcorp DVD-ROM TS-L333A D100 /dev/sr0 [4:0:0:0] disk ATA Hitachi HUA72105 A74A - [4:0:1:0] disk ATA Hitachi HUA72105 A74A - [4:1:0:0] disk Dell VIRTUAL DISK 1028 /dev/sda And there are no block devices in /dev for it: # ls -1 /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4 I tried loading all scsi kernel modules I could find, but that doesn't seem to be the problem. I reall don't get this; it used to work. I found people with similar problems (here and here) but no solution. Initiator is Debian Sqeeuze (testing), target is Debian Lenny (stable). iscsitarget is 0.4.16+svn162-3.1+lenny1, open-iscsi (initiator) is 2.0.871.3-2squeeze1. Target kernel: 2.6.26-2-amd64, initiator kernel: 2.6.32-5-amd64

  Read the article

• Specific DNS sometimes resolves to wildcard, incorrectly

  - by Mojo

  I have an intermittent problem, and I'm not sure where to start trying to troubleshoot it. In our dev environment, we have two visible IP addresses on load balancers, one to the front-end, and one to a number of back-end service machines. The front-end is configured to take a wildcard DNS name to support generic "portals." dev.example.com A 10.1.1.1 *.dev.example.com CNAME dev.example.com The back-end servers are all specific names within the same space: core.dev.example.com A 10.1.1.2 cms.dev.example.com CNAME core.dev.example.com search.dev.example.com CNAME core.dev.example.com Here's the problem. Periodically a developer or a program trying to reach, say, cms.dev.example.com will get a result that points to the front-end, instead of the back-end load balancer: cms.dev.example.com is an alias to core.dev.example.com core.dev.example.com is an alias to dev.example.com (WRONG!) dev.example.com 10.1.1.1 The developers are all on Mac OS X machines, though I've seen the problem occur on an Ubuntu machine as well, using a local cloud host DNS resolver. Sometimes the developer is using a VPN, which directs the DNS to its own resolver, and sometimes he's on the local net using a DNS resolver assigned by the NAT router. Sometimes clearing the Mac OS X DNS cache, logging into the VPN, then logging out of the VPN, will make the problem go away. The origin authoritative server is on zerigo, and a dig directly to their name servers always seems to give the correct answer. The published DNS cache time for these records is 15 minutes, but the problem has been intermittent for about a week. Any troubleshooting suggestions?

  Read the article

• Vista - Profile not Loaded Correctly (Cannot Access Registry)

  - by Geoff

  Every so often, I log on and get the Following Message: User profile was not loaded correctly. You have been logged on with a temporary profile. Changes you make to this profile will be lost when you log off. Please see the event log for details or contact your administrator This almost always happens when somebody else has been on the computer for a while, and then I log on. This never used to happen, but now it happens pretty often. My profile is not permanently corrupted, all I have to do is restart my computer, but this annoys me, and I would like to fix it. I was curios about the reason of this cause, so I looked into the Event Log, and found the root of the problem was the ntuser.dat file in the profile that I was logging on to was locked at logon time. This resulted in the current users registry not being loaded, resulting in failure to load the profile. What could be locking this file? is there any way to get a process list without logging on so that I can identify which process has the file locked? Any other suggestions. Hopefully I can find a solution.

  Read the article

• Fail2Ban adds iptable rules but they are not working?

  - by EApubs

  Fail2Ban just blocked my IP for 3 SSH attempts. It added the iptables rule and I can see it using the "sudo iptables -L -n" command. But I can still access the site and login through SSH! What might be the problem? Is it because im using CloudFlare? I have set Nginx to write the real IPs to the access logs instead of the Cloud Flare IP. Isn't it enough? Chain fail2ban-ssh (1 references) target prot opt source destination DROP all -- 119.235.14.8 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 The input chain : Chain INPUT (policy DROP) target prot opt source destination fail2ban-NoAuthFailures tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 fail2ban-nginx-dos tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,8090 fail2ban-postfix tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 25,465 fail2ban-ssh-ddos tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 ufw-before-logging-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-logging-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-reject-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-track-input all -- 0.0.0.0/0 0.0.0.0/0 LOG all -- 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 4

  Read the article

• How do I secure Sql Server 2008 R2

  - by Mark Tait

  I have both a dedicated and a VPS (from Fasthosts) virtual server - the web sites/applications I run on these, access Sql Server stored on the same web server. Until now, I have logged onto Sql Server on both the deidicated and VPS server, from Sql Server Management Studio - until I noticed in my server application logs, multiple attempts to logon to Sql Server using the 'sa' username, but failed password. So someone/bot is trying hard (repeatedly every couple of hours, for approx 20 attempts during each instance) to log on... so obviously I have to lock down access to Sql Sever remotely. What I have done is gone into Configuration Manager, and in Sql Server Network Configuration - Protocols for Sql2008 and also in Sql Native Client 10.0 Configuration - Client Protocols - I have diabled Named Pipes, TCP/IP (and VIA by default). I have left Shared Memory enabled. I also disabled in Sql Server Services, the Sql Server Browser. Now the only way I can manage the databases on these servers, is by logging on to them via Remote Desktop. Can anyone confirm if this is the correct way of stopping anyone maliciously logging on to Sql Server? (I'm not a DBA or security expert - and there are hundreds of articles advising all different ways - but I was hoping for the experts here to confirm, or otherwise, if what I've done is correct) Thank you, Mark

  Read the article

• Ubuntu Pound Reverse Proxy Load Balancing Based off active server load?

  - by Andrew

  I have Pound installed on a loadbalancer. It seems to work okay, except that it randomly assigns the backend server to forward the request to. I've put 1 backend machine under so much load that it went into using swap, and I can't even ssh into it to test this scenareo. I would like the loadbalancer to realize that the machine is overloaded, and send it to a different backend machine. However it doesn't. I've read the man page and it seems like the directive "DynScale 1" is what would monitor this, but it still redirects to the overloaded server. I've also put in "HAport 22" to the backend figuring since I can't ssh in, neither could the loadbalancer and it would consider the backend server dead until it gets rid of the load and responds, but that didn't help either. If anyone could help with this, I'd appreciate it. My current config is below. ###################################################################### ## global options: User "www-data" Group "www-data" #RootJail "/chroot/pound" ## Logging: (goes to syslog by default) ## 0 no logging ## 1 normal ## 2 extended ## 3 Apache-style (common log format) LogLevel 3 ## check backend every X secs: Alive 5 DynScale 1 Client 1200 TimeOut 1500 # poundctl control socket Control "/var/run/pound/poundctl.socket" ###################################################################### ## listen, redirect and ... to: ## redirect all requests on port 80 to SSL ListenHTTP Address 192.168.1.XX Port 80 Service Redirect "https://xxx.com/" End End ListenHTTPS Address 192.168.1.XX Port 443 Cert "/files/www.xxx.com.pem" Service BackEnd Address 192.168.1.1 Port 80 HAport 22 End BackEnd Address 192.168.1.2 Port 80 HAport 22 End End End

  Read the article

• Cant kill process on Windows Server 2008!! - Thread in Wait:Executive State

  - by adrian

  I hope someone can help me with our issue we are having. We have a major issue with a process that we can not kill and the only way to get rid of the process is to reboot the machine. I have tried killing it from the normal task manager but no joy. I have tried killing it using the taskkill /F command from a command prompt and no joy. The command reports as sucessful but the process remains. I have tried to start task manager with system rights by calling "psexec -s -i -d taskmgr" and attempting to kill the process but no joy I have tried killing it from Process Explorer but again the process remains. I have tried creating a scheduled task that runs under the SYSTEM name to kill the task but that also does not kill it : schtasks /create /ru system /sc once /st 13:16 /tn test1 /tr "taskkill /F /PID 1576" /it Nothing I do will kill this process. Even logging off and logging back on will not kill this process. Using Process Explorer I notice that there is on stubborn thread that is in the Wait:Executive state. I have tried to kill this thread using Process Explorer but again no joy. We are using Windows Server 2008 R2 64-Bit. The server is brand new and windows is freshly installed. Now heres the thing. We have brought two identical servers from Dell with the same specs and the same OS installed and I can not replicate this issue on the other server. Only on this server, under certain circumstances does this server process hang and can not be restarted! I have also changed the compatability mode by setting it the process to "Windows 2003" but this has not helped. I have noticed in Process Explorer that DEP is turned on but im not sure this has got any bearing on the issue ot not. Please, can someone help??

  Read the article

• Recommend a free temperature-monitoring utility for cores + video card, on Vista?

  - by smci

  Looking for your recommendations for a free temperature-monitoring utility, for my PC (Core 2) and graphics card for Vista. (Question reposted with the hyperlinks now I have 10 reputation). I don't want all the geeky details, I don't overclock, I don't see the need to mess with my fan speeds or motherboard settings, I just want something fairly basic to help with basic troubleshooting of intermittent overheats on video card and/or mobo: must run on Windows Vista (yes, don't laugh). ideally displays temperature when minimized to toolbar, and/or: automatically alerts me when temperature on either core or the video card exceeds a threshold ideally measures temperature of video card and system as well, not just the cores. HDD temperature is not necessary I think. logging is nice, graphs are also nice portability to Linux and Mac is nice Apparently Everest is the best paid option, but I'm not prepared to spend $40. I found the following free options, but no head-to-head at-a-glance comparison: CoreTemp (only does cores, not video card?) Open Hardware Monitor (nice graphs, displays when minimized to toolbar, no alerts) RealTemp (has alerts, works minimized, lightweight install) HWMonitor (no alerts, CNET: "[free version is] simple but effective") from CPUID CPUCool (not free: 21-day trialware, then $18) SpeedFan from Almico (too geeky, detail overload; CNET: "most users won't be able to make head or tail of the data this utility provides") Motherboard Monitor (CNET: not recommended, requires expert knowledge of your mobo, dangerous) Intel Thermal Analysis Tool (only does cores, not video card? has logging) Useful discussions I found: hardwarecanucks.com , superuser.com 1, 2 , forums.techarena.in (Update: I downloaded Real Temp 3.60 and it meets all my needs, the customizable alert temperature is great. Open Hardware Monitor seems to be the other one that mostly meets my needs, except no alerts; but it is portable. I tried SpeedFan but the interface is very cluttered, too much unnecessary detail (needs a Basic/Advanced mode and a revamp of the interface.) The answer to my underlying issue is nVidia Geforce LE 7500 video card which runs very hot.)

  Read the article

• /etc/hosts: What is loghost? (fresh install of Solaris 10 update 9)

  - by cjavapro

  # # Internet host table # ::1 localhost 127.0.0.1 localhost XX.XX.XX.XX myserver loghost What is the purpose of loghost? If it was not for having loghost in there, all the /etc/hosts files on all the servers in this particular network could be identical. Edit: I looked at /etc/syslog.conf #ident "@(#)syslog.conf 1.5 98/12/14 SMI" /* SunOS 5.0 */ # # Copyright (c) 1991-1998 by Sun Microsystems, Inc. # All rights reserved. # # syslog configuration file. # # This file is processed by m4 so be careful to quote (`') names # that match m4 reserved words. Also, within ifdef's, arguments # containing commas must be quoted. # *.err;kern.notice;auth.notice /dev/sysmsg *.err;kern.debug;daemon.notice;mail.crit /var/adm/messages *.alert;kern.err;daemon.err operator *.alert root *.emerg * # if a non-loghost machine chooses to have authentication messages # sent to the loghost machine, un-comment out the following line: #auth.notice ifdef(`LOGHOST', /var/log/authlog, @loghost) mail.debug ifdef(`LOGHOST', /var/log/syslog, @loghost) # # non-loghost machines will use the following lines to cause "user" # log messages to be logged locally. # ifdef(`LOGHOST', , user.err /dev/sysmsg user.err /var/adm/messages user.alert `root, operator' user.emerg * ) Very interesting. when shutting down,, alerts go to all users probably through *.emerg * Looking at ifdef, it seems that the first parameter checks to see if current machine is a loghost, second parameter is what to do if it is and third parameter is what to do if it is not. Edit: If you want to test a logging rule you can use svcadm restart system-log to restart the logging service and then logger -p notice "test" to send a test log message where notice can be replaced with any type such as user.err, auth.notice, etc.

  Read the article

• INSERT DELAYED on locked tables blocks PHP processes to continue

  - by sw0x2A

  Our webservers write some tracking information into a MySQL database (using INSERT DELAYED into MyISAM table). When a huge SELECT query is executed on this table or when it is locked for another reason, the webserver processes (with INSERT DELAYED) are waiting for the database and in some cases the MaxServer limit is reached in Apaches, so they will stop serving requests. We use INSERT DELAYED because The DELAYED option for the INSERT statement is a MySQL extension to standard SQL that is very useful if you have clients that cannot or need not wait for the INSERT to complete. This is a common situation when you use MySQL for logging and you also periodically run SELECT and UPDATE statements that take a long time to complete. Quote from MySQL documentation. I am wondering why the Apache processes are waiting for the INSERT DELAYED to finish. And what can I do to just send the data and forget about it. (Since this is logging data, I do not care if we lose some entries.) Even when the table is locked the PHP script should just go on and should not wait for an answer of MySQL. (We do not want to setup Master-slave for this table but we are thinking about move this data to some NoSQL database. But for now I would like to know why INSERT DELAYED is not working as expected.)

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >