Search Results

Search found 4619 results on 185 pages for 'kernel panic'.

Page 82/185 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• ifconfig return "unknown interface: no such device"

  - by xolstice

  I'm trying to install a Linux driver for my wireless network card (D-Link DWL-G510) on my Red Hat Linux 7.1 machine with a 2.4.37.9 kernel. I downloaded the serial monkey driver from the sourceforge site and was able to successfully compile the rt73 module and load it into the kernel. The problem now is that everytime I issue the command ifconfig wlan0 up it keeps returning with the following error message: wlan0: unknown interface: No such device. I'm at a loss as to what to do here. I specifed wlan0 as the alias for the rt73 module in the modules.conf and also tried to load the driver with the command modprobe rt73 ifname=wlan0 (this specifies the interface name according to the instructions packaged in the driver), but the error message still keeps coming up. Is there something else I need to do in Linux to configure the wlan0 part or is the module not recognizing the wireless network card? It would be quite strange if it is the later since all information from the Internet is indicating this is the linux driver I should be using for mentioned wireless card.

  Read the article

• How to disable hiddev96 in linux (or tell it to ignore a specific device)

  - by Miky D

  I'm having problems with a CentOS 5.0 system when using a certain USB device. The problem is that the device advertises itself as a HID device and linux is happy to try to provide support for it: In /ver/log/messages I see a line that reads: hiddev96: USB HID 1.11 Device [KXX USB PRO] on usb-0000:00:1d.0-1 My question comes down to: Is there a way to tell linux to not use hiddev96 for that device in particular? If yes, how? If not, what are my options - can I turn hiddev96 off completely? UPDATE I should probably have been a bit more specific about what is going on. The machine is running Centos 5.0, and on top of it I'm running VMWare workstation with Windows XP - which is where the USB device is actually supposed to operate. All works fine for other USB devices (i.e. VMWare successfully connects the USB device to the guest OS and the OS can use it, but for this particular device VMWare connects it to the guest OS, but the OS can't read/write to it) Every attempt locks up the application that is trying to communicate with the device. I've reason to believe that it is because the device is a HID device and there's some contention between the Linux host and the Windows guest OS in accessing the device. Below is the output from modprobe -l|grep -i hid as requested by @Karolis: # modprobe -l | grep -i hid /lib/modules/2.6.18-53.1.14.el5/kernel/net/bluetooth/hidp/hidp.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetservo.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetkit.ko And here is the output of lsmod # lsmod Module Size Used by udf 76997 1 vboxdrv 65696 0 autofs4 24517 2 hidp 23105 2 rfcomm 42457 0 l2cap 29633 10 hidp,rfcomm tun 14657 0 vmnet 49980 16 vmblock 20512 3 vmmon 945236 0 sunrpc 144253 1 cpufreq_ondemand 10573 1 video 19269 0 sbs 18533 0 backlight 10049 0 i2c_ec 9025 1 sbs button 10705 0 battery 13637 0 asus_acpi 19289 0 ac 9157 0 ipv6 251393 27 lp 15849 0 snd_hda_intel 24025 2 snd_hda_codec 202689 1 snd_hda_intel snd_seq_dummy 7877 0 snd_seq_oss 32577 0 nvidia 7824032 31 snd_seq_midi_event 11073 1 snd_seq_oss snd_seq 49713 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 11725 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 42945 0 snd_mixer_oss 19009 1 snd_pcm_oss snd_pcm 72133 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss joydev 13313 0 sg 36061 0 parport_pc 29157 1 snd_timer 24645 2 snd_seq,snd_pcm snd 52421 13 snd_hda_intel,snd_hda_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer ndiswrapper 170384 0 parport 37513 2 lp,parport_pc hci_usb 20317 2 ide_cd 40033 1 tg3 104389 0 i2c_i801 11469 0 bluetooth 53925 8 hidp,rfcomm,l2cap,hci_usb soundcore 11553 1 snd cdrom 36705 1 ide_cd serio_raw 10693 0 snd_page_alloc 14281 2 snd_hda_intel,snd_pcm i2c_core 23745 3 i2c_ec,nvidia,i2c_i801 pcspkr 7105 0 dm_snapshot 20709 0 dm_zero 6209 0 dm_mirror 28741 0 dm_mod 58201 8 dm_snapshot,dm_zero,dm_mirror ahci 23621 4 libata 115833 1 ahci sd_mod 24897 5 scsi_mod 132685 3 sg,libata,sd_mod ext3 123337 3 jbd 56553 1 ext3 ehci_hcd 32973 0 ohci_hcd 23261 0 uhci_hcd 25421 0

  Read the article

• Linux networking crash: best steps to find out the cause?

  - by Aron Rotteveel

  One of our Linux (CentOS) servers was unreachable last night. The server was not reachable in any way except for the remote console. After logging in with the remote console, it turned out I could not ping any outside hosts either. A simple service network restart solved the issue, but I am still wondering what could have caused this. My log files seem to indicate no error at all (except for the various daemons that need a network connection and failed after the network failure). Are there any additional steps I can take to find out the cause of this problem? EDIT: this just happened again. The server was completely unresponsive until I issued a networking service restart. Any advise is welcome. Could this be caused by a faulty hardware component? As per Madhatters request, here are some excerpts from the log at the time (the network crashed at 20:13): /var/log/messages: Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=100 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:13:34 graviton junglediskserver: Connection to gateway failed: xGatewayTransport - Connection to gateway failed. The first three messages are simple responses to iptables rules I have set up through the LFD firewall. The last message indicates that JungleDisk, which I use for backups can no longer connect to the gateway. Apart from this, there are no interesting messages around this time. EDIT 4 dec: as per Mattdm's request, here is the output of ethtool eth0: (Please not that these are the settings that currently work. If things go wrong again, I will be sure to post this again if necessary. Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Link detected: yes As per Joris' request, here is also the output of route -n: aron@graviton [~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.58 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.42 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.43 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.41 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.46 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.47 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.44 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.45 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.50 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.51 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.48 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.49 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.54 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.52 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.53 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 xx.xx.xx.62 0.0.0.0 UG 0 0 0 eth0 The bottom xx.62 is my gateway. EDIT december 28th: the problem occurred again and I got the chance to compare some of the outputs of the above tests. What I found out is that arp -an returns an incomplete MAC address for my gateway (which is not under my control; the server is in a shared rack): During failure: ? (xx.xx.xx.62) at <incomplete> on eth0 After service network restart: ? (xx.xx.xx.62) at 00:00:0C:9F:F0:30 [ether] on eth0 Is this something I can fix or is it time for me to contact the data centre?

  Read the article

• elilo commandline boot config that includes spaces

  - by qdot

  I've got an elilo (EFI LILO) config file that includes spaces in the label - like that: image=/EFI/gentoo/boot/kernel-genkernel-ia64-3.1.6-gentoo label="Gentoo IA64 3.1.6" append="real_root=/dev/sda2" initrd=/EFI/gentoo/boot/initramfs-genkernel-ia64-3.1.6-gentoo read-only How can I select this label from ELILO's command line - the usual suspects: Gentoo IA64 3.1.6 "Gentoo IA64 3.1.6" 'Gentoo IA64 3.1.6' Gentoo\ IA64\ 3.1.6 all fail with the Kernel file not found Gentoo/"Gentoo/'Gentoo/Gentoo\" kind of error. Surely there must be a way to use a 'space' without making it a parameter delimeter?

  Read the article

• Boot xen server through ipxe

  - by Ghassen Telmoudi

  I'm want install Xen Server 6.2 though ipxe, I tried different configurations, no luck making to work until now. I found some may example to boot from pxe using TFTP server, and here is an example: default xenserver-auto label xenserver-auto kernel mboot.c32 append xenserver/xen.gz dom0_max_vcpus=1-2 dom0_mem=752M,max:752M com1=115200,8n1 console=com1,vga --- xenserver/vmlinuz xencons=hvc console=hvc0 console=tty0 answerfile=http://[pxehost]/answerfile.xml remotelog=[SYSLOG] install --- xenserver/install.img The problem is that ipxe uses different syntax, I could not figure out how to convert this configuration to work on ipxe. Here is my ipxe file so far: #!ipxe echo "XEN Server is booting up" initrd http://server-ip/pxe/xen/boot/xen.gz kernel http://server-ip/pxe/xen/boot/pxelinux/mboot.c32 boot Can any one supply the correct configuration?

  Read the article

• How to tell if PAE is hurting me?

  - by James

  I have a couple of servers with 20-30 GB RAM that are running (a variant of) RHEL4. They are currently running the SMP i386 kernel, not x64, not even the hugemem kernel. This means LowMem is confined to < 1G, and thus dentry_cache and ext3_inode_cache to 100M or so each. How can I tell if this is a problem? Here's a typical vmstat report while it's compiling some Java: $ vmstat 10 procs -----------memory---------- ---swap-- -----io---- --system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 1 1 0 19493816 394740 922420 0 0 1058 2292 1491 1020 6 3 80 12 2 1 0 19519480 395244 850156 0 0 1179 1412 1329 1195 9 4 75 12 1 1 0 19557368 392616 828344 0 0 1783 1680 1498 1756 14 5 72 9 I don't like the way bi is nonzero when there is so much memory free. I imagine slabtop could point more directly to the problem but I don't really understand how to interpret its output.

  Read the article

• Linux box acting as wireless access point to share the internet connection

  - by Suresh

  A linux machine is connected to internet over two interfaces ppp0 and ppp1 using two modems. Also this machine acts as wireless access point through an interface say, eth0 with ip address 192.168.1.1 and acts as gateway for the connected devices through this network with subnet mask 255.255.255.0 Now is it possible to achieve the following: When any of the connected devices through wireless AP needs internet connection linux machine has to use ppp1 interface for internet. If any of the applications on the linux machine needs internet connection linux machine should use ppp0 interface for the internet. Can this be achieved by adding rules to chains in filter/nat tables? If the kernel routing table has a default rule to route the default traffic through interface ppp0, wil kernel completely ignore ppp1 for internet? PS: new to networking and routing concepts, If the question is not clear leave a comment, will try to give more information.

  Read the article

• Limiting Sybase ASE 15 CPU usage on VM

  - by reiniero

  I've set up a single CPU Sybase ASE 15.7 test/hobby/experimentation system on a Debian Squeeze x64 KVM VM. I notice the CPU load goes to 100% and stays there. Definitely not a Sybase guru, only interested to see if some programs I'm running work on the database. Looking at Sybase docs it seems ASE detects the machine is idle and then takes over all processing just waiting for a connection (and if needed, doing some housekeeping apparently). Normally that would be fine but as it is running in a VM it's taking away processor resources other VMs could use - and the increased fan noise of the PC near my desk annoy me. I've tried to remedy this: set the "runnable process search count" parameter from DEFAULT (2000 IRC) to 3 in /opt/sybase/ASE-15_0/SYBASE.cfg from http://sybase.reygrobellet.com/tutorials/install_sybase_vb/standalone04_configure_oralin11#TOC-Configure-kernel I added this to my /etc/init.d/sybase startup script: echo 0 /proc/sys/kernel/randomize_va_space (though I don't think it'll make much difference) How can I tell Sybase to "behave" and not hog the processor - I don't mind reduced performance.

  Read the article

• OpenAFS on Fedora/CentOS

  - by Michael Pliskin

  I am trying to see if OpenAFS fits my needs as a distributed filesystem and is a bit stuck. There are docs but they're all quite hard to understand, so asking for some expert advice here. My questions: which version to install? I need windows client support so I need 1.5 - right? But it is not stable.. Or is it? And don't see any pre-built rpms for it, so compiling from sources? tried to compile and it worked but it created a non-"mp" kernel module while my kernel needs an mp one - how to workaround that? do I really need a new fresh partition to start with or I can re-use an existing one and just make it available via afp? any nice HOWTOs around?

  Read the article

• Why does my Mac always crash when I enable `ask for password after screensaver ended`?

  - by Koning Baard XIV

  I have enabled these two things: Placing the mouse-pointer in the bottom-left corner of any display makes the screensaver appear After the screensaver or stand-by has ended, ask for password However, this combination always leads to this (Black Screen of Death) after entering the screensaver with the bottom-left corner: Here are my system specs: Hardware Overview: Model Name: iMac Model Identifier: iMac9,1 Processor Name: Intel Core 2 Duo Processor Speed: 2,66 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache: 6 MB Memory: 2 GB Bus Speed: 1,07 GHz Boot ROM Version: IM91.008D.B08 SMC Version (system): 1.44f0 Serial Number (system): W89171JF0TF Hardware UUID: 323A90F0-8A2F-5057-B501-2087489E0DFF System Software Overview: System Version: Mac OS X 10.6.3 (10D573) Kernel Version: Darwin 10.3.0 Boot Volume: Macintosh HD Boot Mode: Normal Computer Name: YOU SHOULD NOT KNOW THIS User Name: YOU SHOULD NOT KNOW THIS Secure Virtual Memory: Not Enabled 64-bit Kernel and Extensions: No Time since boot: 11:46 Can anyone help me? Thanks

  Read the article

• Is it OK to use images of GPD'd code in a CC 3.0 BY video?

  - by marcusw

  I am making a video in which I would like to use pictures of some Linux Kernel code. I am looking to release the finished product under the CC 3.0 BY license, but the Kernel is released under the GPL, which would not allow this if the code is in text format. However, since it will be in low-resolution, incredibly incomplete, non-usable, non-compilable, non-editable (at least without lots of finagling) format, would this constitute fair use or find another loophole to slip through? Thanks for the help, I will understand if this is considered off topic.

  Read the article

• Linux policy routing - packets not coming back

  - by Bugsik

  i am trying to set up policy routing on my home server. My network looks like this: Host routed VPN gateway Internet link through VPN 192.168.0.35/24 ---> 192.168.0.5/24 ---> 192.168.0.1 DSL router 10.200.2.235/22 .... .... 10.200.0.1 VPN server The traffic from 192.168.0.32/27 should be and is routed through VPN. I wanted to define some routing policies to route some traffic from 192.168.0.5 through VPN as well - for start - from user with uid 2000. Policy routing is done using iptables mark target and ip rule fwmark. The problem: When connecting using user 2000 from 192.168.0.5 tcpdump shows outgoing packets, but nothing comes back. Traffic from 192.168.0.35 works fine (here I am not using fwmark but src policy). Here is my VPN gateway setup: # uname -a Linux placebo 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux # iptables -V iptables v1.4.12 # ip -V ip utility, iproute2-ss111117 IPtables rules (all policies in table filter are ACCEPT) # iptables -t mangle -nvL Chain PREROUTING (policy ACCEPT 770K packets, 314M bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 767K packets, 312M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 5520 packets, 1920K bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 782K packets, 901M bytes) pkts bytes target prot opt in out source destination 74 4707 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner UID match 2000 MARK set 0x3 Chain POSTROUTING (policy ACCEPT 788K packets, 903M bytes) pkts bytes target prot opt in out source destination # iptables -t nat -nvL Chain PREROUTING (policy ACCEPT 996 packets, 51172 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 7 packets, 432 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1364 packets, 112K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 2302 packets, 160K bytes) pkts bytes target prot opt in out source destination 119 7588 MASQUERADE all -- * vpn 0.0.0.0/0 0.0.0.0/0 Routing: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master lan state UNKNOWN qlen 1000 link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff valid_lft forever preferred_lft forever 3: lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff inet 192.168.0.5/24 brd 192.168.0.255 scope global lan inet6 fe80::240:63ff:fef9:c38f/64 scope link valid_lft forever preferred_lft forever 4: vpn: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100 link/none inet 10.200.2.235/22 brd 10.200.3.255 scope global vpn # ip rule show 0: from all lookup local 32764: from all fwmark 0x3 lookup VPN 32765: from 192.168.0.32/27 lookup VPN 32766: from all lookup main 32767: from all lookup default # ip route show table VPN default via 10.200.0.1 dev vpn 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 # ip route show default via 192.168.0.1 dev lan metric 100 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 TCP dump showing no traffic coming back when connection is made from 192.168.0.5 user 2000 # tcpdump -i vpn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vpn, link-type RAW (Raw IP), capture size 65535 bytes ### Traffic from user 2000 on 192.168.0.5 ### 10:19:05.629985 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6887764 ecr 0,nop,wscale 4], length 0 10:19:21.678001 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6891776 ecr 0,nop,wscale 4], length 0 ### Traffic from 192.168.0.35 ### 10:23:12.066174 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [S], seq 2294159276, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 557451322 ecr 0,sackOK,eol], length 0 10:23:12.265640 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [S.], seq 2521908813, ack 2294159277, win 14480, options [mss 1367,sackOK,TS val 388565772 ecr 557451322,nop,wscale 1], length 0 10:23:12.276573 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [.], ack 1, win 8214, options [nop,nop,TS val 557451534 ecr 388565772], length 0 10:23:12.293030 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [P.], seq 1:480, ack 1, win 8214, options [nop,nop,TS val 557451552 ecr 388565772], length 479 10:23:12.574773 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [.], ack 480, win 7776, options [nop,nop,TS val 388566081 ecr 557451552], length 0

  Read the article

• What can I do to give some more love and disk space to my database on Ubuntu?

  - by Yaron Naveh

  I'm new to linux. I've deployed a db to ubuntu server on amazon and found out I'm low on disk space. did df (see below) - and found out that I'm 89% capacity on one file system, but less on others. What does this mean? Do I have a few partitions and can now utilize others besides /dev/xvda1? Also /dev/xvdb seems large, is it safe to put the db in it and only use it? If so do I need to mount it or do something special? $> df -lah Filesystem Size Used Avail Use% Mounted on /dev/xvda1 8.0G 6.7G 914M 89% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 3.7G 8.0K 3.7G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.5G 164K 1.5G 1% /run none 5.0M 0 5.0M 0% /run/lock none 3.7G 0 3.7G 0% /run/shm /dev/xvdb 414G 199M 393G 1% /mnt

  Read the article

• Xen 4.0.1 on Ubuntu 10.10 not booting

  - by Disco

  I'm trying to get Xen 4.0.1 run as dom0 on a fresh/clean install of 10.10 desktop (x64). Followed the step by step tutorial at http://wiki.xensource.com/xenwiki/Xen4.0 I have the pvops kernel in /boot, also included the ext4 fs support by recompiling the kernel by : make -j6 linux-2.6-pvops-config CONFIGMODE=menuconfig make -j6 linux-2.6-pvops-build make -j6 linux-2.6-pvops-install Here's my grub entry : menuentry 'Xen4' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 insmod ext3 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set 2bf3177a-92fd-4196-901a-da8d810b04b4 multiboot /xen-4.0.gz dom0_mem=1024M loglvl=all guest_loglvl=all module /vmlinuz-2.6.32.27 root=UUID=2bf3177a-92fd-4196-901a-da8d810b04b4 ro module /initrd.img-2.6.32.27 } blkid /dev/sda1 gives the : /dev/sda1: UUID="2bf3177a-92fd-4196-901a-da8d810b04b4" TYPE="ext3" My partition shemes is : /boot (ext3) / (ext4) Whatever option i've tried i end up with : mounting none on /dev failed: no such file or directory And message complaining that it cannot find the device with uuid ... It's taking my hairs out, if somone has a clue ...

  Read the article

• change default port of IIS and let another process to listen on port 80 (Windows Server 2008)

  - by aleroot

  I have an installation of Windows Server 2008 running IIS 6 with a website listening on port 8080, even though I have moved the website to listen on 8080, port 80 is still kept in use by IIS (for truth by the kernel process : System - ProcId : 4). I want to let another process listen on port 80 without uninstalling or disabling IIS, I want to keep IIS listening on port 8080 and another service on port 80, is there a way to do it? I saw another similar thread here on serverfault but the solution (using httpcfg.exe delete iplisten -i 0.0.0.0:80 ) can work only in 2003 because in 2008 the utility httpcfg.exe doesn't exist and it seems that it cannot be installed ... Does anyone have a solution to get rid of the kernel listening on port 80 in Windows Server 2008 with IIS running?

  Read the article

• Is it OK to use images of GPL'd code in a CC 3.0 BY video?

  - by marcusw

  I am making a video in which I would like to use pictures of some Linux Kernel code. I am looking to release the finished product under the CC 3.0 BY license, but the Kernel is released under the GPL, which would not allow this if the code is in text format. However, since it will be in low-resolution, incredibly incomplete, non-usable, non-compilable, non-editable (at least without lots of finagling) format, would this constitute fair use or find another loophole to slip through? Thanks for the help, I will understand if this is considered off topic.

  Read the article

• How to disable hiddev96 in linux (or tell it to ignore a specific device)

  - by Miky D

  I'm having problems with a CentOS 5.0 system when using a certain USB device. The problem is that the device advertises itself as a HID device and linux is happy to try to provide support for it: In /ver/log/messages I see a line that reads: hiddev96: USB HID 1.11 Device [KXX USB PRO] on usb-0000:00:1d.0-1 My question comes down to: Is there a way to tell linux to not use hiddev96 for that device in particular? If yes, how? If not, what are my options - can I turn hiddev96 off completely? UPDATE I should probably have been a bit more specific about what is going on. The machine is running Centos 5.0, and on top of it I'm running VMWare workstation with Windows XP - which is where the USB device is actually supposed to operate. All works fine for other USB devices (i.e. VMWare successfully connects the USB device to the guest OS and the OS can use it, but for this particular device VMWare connects it to the guest OS, but the OS can't read/write to it) Every attempt locks up the application that is trying to communicate with the device. I've reason to believe that it is because the device is a HID device and there's some contention between the Linux host and the Windows guest OS in accessing the device. Below is the output from modprobe -l|grep -i hid as requested by @Karolis: # modprobe -l | grep -i hid /lib/modules/2.6.18-53.1.14.el5/kernel/net/bluetooth/hidp/hidp.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetservo.ko /lib/modules/2.6.18-53.1.14.el5/kernel/drivers/usb/misc/phidgetkit.ko And here is the output of lsmod # lsmod Module Size Used by udf 76997 1 vboxdrv 65696 0 autofs4 24517 2 hidp 23105 2 rfcomm 42457 0 l2cap 29633 10 hidp,rfcomm tun 14657 0 vmnet 49980 16 vmblock 20512 3 vmmon 945236 0 sunrpc 144253 1 cpufreq_ondemand 10573 1 video 19269 0 sbs 18533 0 backlight 10049 0 i2c_ec 9025 1 sbs button 10705 0 battery 13637 0 asus_acpi 19289 0 ac 9157 0 ipv6 251393 27 lp 15849 0 snd_hda_intel 24025 2 snd_hda_codec 202689 1 snd_hda_intel snd_seq_dummy 7877 0 snd_seq_oss 32577 0 nvidia 7824032 31 snd_seq_midi_event 11073 1 snd_seq_oss snd_seq 49713 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 11725 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 42945 0 snd_mixer_oss 19009 1 snd_pcm_oss snd_pcm 72133 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss joydev 13313 0 sg 36061 0 parport_pc 29157 1 snd_timer 24645 2 snd_seq,snd_pcm snd 52421 13 snd_hda_intel,snd_hda_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer ndiswrapper 170384 0 parport 37513 2 lp,parport_pc hci_usb 20317 2 ide_cd 40033 1 tg3 104389 0 i2c_i801 11469 0 bluetooth 53925 8 hidp,rfcomm,l2cap,hci_usb soundcore 11553 1 snd cdrom 36705 1 ide_cd serio_raw 10693 0 snd_page_alloc 14281 2 snd_hda_intel,snd_pcm i2c_core 23745 3 i2c_ec,nvidia,i2c_i801 pcspkr 7105 0 dm_snapshot 20709 0 dm_zero 6209 0 dm_mirror 28741 0 dm_mod 58201 8 dm_snapshot,dm_zero,dm_mirror ahci 23621 4 libata 115833 1 ahci sd_mod 24897 5 scsi_mod 132685 3 sg,libata,sd_mod ext3 123337 3 jbd 56553 1 ext3 ehci_hcd 32973 0 ohci_hcd 23261 0 uhci_hcd 25421 0

  Read the article

• Hostname problems in CentOS 5.5

  - by spoon16

  I just set up a CentOS 5.5 machine on my local network and attempted to modify the hostname by editing /etc/sysconfig/network file. When I'm logged in locally the change to the hostname is reflected and seems to be working fine. When I open a SSH session via PuTTY from Windows this is what I see at the prompt: [root@? ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes HOSTNAME=mini.local [root@? ~]# sysctl kernel.hostname kernel.hostname = ? [root@? ~]# hostname ? [root@? ~]# hostname -f hostname: Unknown server error A couple of other symptoms that may be helpful in troubleshooting this problem. I can ping the CentOS box from my Windows machine via IP but not hostname. Also, my Netgear router does not display the hostname when I view the "Connected Devices", I do see the mac address and the proper IP listed though. How can I make it so that the hostname is properly propagated throughout my network?

  Read the article

• OpenAFS on Fedora/CentOS

  - by Michael Pliskin

  I am trying to see if OpenAFS fits my needs as a distributed filesystem and is a bit stuck. There are docs but they're all quite hard to understand, so asking for some expert advice here. My questions: which version to install? I need windows client support so I need 1.5 - right? But it is not stable.. Or is it? And don't see any pre-built rpms for it, so compiling from sources? tried to compile and it worked but it created a non-"mp" kernel module while my kernel needs an mp one - how to workaround that? do I really need a new fresh partition to start with or I can re-use an existing one and just make it available via afp? any nice HOWTOs around?

  Read the article

• Can not boot CentOS VM using VirtIO in KVM

  - by Jake

  I converted qcow2 image to raw and changed I/O bus to VirtIO for a VM. now I can't boot that VM. I Installed VirtIO driver with following command: mkinitrd --with virtio_pci --with virtio_blk -f /boot/initrd-$(uname -r).img $(uname -r) and these are related kernel modules: virtio_balloon 11329 0 virtio_blk 11593 3 virtio_pci 11845 0 virtio_ring 8513 1 virtio_pci virtio 9541 3 virtio_balloon,virtio_blk,virtio_pci and this is what happens during boot-up. I also changed /boot/grub/device.map from "(hd0) /dev/sda" to "(hd0) /dev/vda" but problem still exists. any ideas how to fix this ? This is my default option to boot: title CentOS (2.6.18-308.13.1.el5) root (hd0,0) kernel /vmlinuz-2.6.18-308.13.1.el5 ro root=/dev/VolGroup00/LogVol00 initrd /initrd-2.6.18-308.13.1.el5.img

  Read the article

• Dualbooting Win7 and Gentoo, error

  - by Tommy Jakobsen

  Hello I'm trying to setup a dualboot with Gentoo Linux and Windows 7. Heres my partitions: /dev/sda1 /boot partition, ext2 /dev/sda2 win7 partition, ntfs /dev/sda3 swap partition, linux swap /dev/sda4 root partition, btrfs Using Grub, I can boot into Gentoo, but when I'm choosing to boot Windows 7, nothing happens. It just writes the Grub options for that choice, and then it hangs. grub.conf: default 0 timeout 30 title Gentoo root (hd0,0) kernel /boot/kernel-x86_64-2.6.31 root=/dev/sda4 title Windows rootnoverify (hd0,1) makeactive chainloader +1 Any ideas? Help will be much appreciated!

  Read the article

• vmware linux headers not found for ubuntu 10.10 ?

  - by Tumbleweed

  I've installed Vmware 6.5 on Ubuntu 10.10... when I start vmware player/workstation its asking for linux kernel header for some compilation but I'm not able to find the appropriate package, see the Image below.... Update after running following commands sudo -s cd /lib/modules/$(uname -r)/build/include/linux ln -s ../generated/utsrelease.h ln -s ../generated/autoconf.h Error has been changed like below.... ERROR: modinfo: could not find module vmmon ERROR: modinfo: could not find module vmnet ERROR: modinfo: could not find module vmblock ERROR: modinfo: could not find module vmci ERROR: modinfo: could not find module vsock Using 2.6.x kernel build system. make: Entering directory /tmp/vmware-root/modules/vmmon-only' make -C /lib/modules/2.6.35-22-generic/build/include/.. SUBDIRS=$PWD SRCROOT=$PWD/. modules make[1]: Entering directory/usr/src/linux-headers-2.6.35-22-generic' CC [M] /tmp/vmware-root/modules/vmmon-only/linux/driver.o In file included from /tmp/vmware-root/modules/vmmon-only/linux/driver.c:31: /tmp/vmware-root/modules/vmmon-only/./include/compat_wait.h:78: error: conflicting types for ‘poll_initwait’ include/linux/poll.h:72: note: previous declaration of ‘poll_initwait’ was here

  Read the article

• Connection to mysql server in SYN_SENT

  - by Sunil

  We are facing a strange problem from last few days between our application server and database server(Mysql): connection to database server from application server hangs in SYN_SENT state and after that we are not able to make any connection to database server on mysql port(3306). When we checked the netstat output on database server its in SYN_RECV state. What I can figure out is mysql server is receiving the SYN request and responding also and its not reaching to the client hence SYN_RECV at server side and SYN_SENT at client side. I think SYN_SENT state should go after some time and because of this other db connection attempts to same server should not hang. Does anybody have any idea how can we resolve this issue? Out setup details : Application server: RHEL 5.4, kernel-release = 2.6.18-164.el5, x86_64 Database server: Mysql Version : 5.1.49 RHEL 5.4, kernel-release = 2.6.18-164.el5, x86_64

  Read the article

• No login prompt displayed after updating Ubuntu 10.04, broken gdm

  - by cliff

  So here's what happens: I updated my system the other day, was prompted for a reboot for the update to complete but was in the middle of working so I delayed it until after I was done. I reboot and it's broken :(. It appears to boot normally, with the following exceptions: The purple Ubuntu load screen no longer displays (though it did for the first couple of times I tried to get in). I hear the login prompt sound, but no login prompt appears. Nor is it simply "invisible" - pressing enter, typing my password, and pressing enter again do nothing. Normally my Bluetooth mouse is functional at this point, but it is not. GRUB displays recovery options for my current kernel, and for an older one (2.6.32-24). Trying to boot into .32-24 gives me an error saying "udevadm can't do something while udev is not configured". So I try solutions listed here: http://superuser.com/questions/195786/ubuntu-update-went-wrong-pc-doesnt-boot-how-can-i-repair-it Nothing I tried seemed to work, and after further Googling my hunch is that it's a problem with gdm. Please correct me if I'm wrong, I don't know all that much about how Linux/Ubuntu systems work just yet. Things I'm able to do: Boot to a live CD Ctrl-Alt-F2 after that login sound plays brings me to a console login, which I can successfully do (it's how I tried the solutions above). This works only under the current kernel. A hack I'd be willing to explore is removing the login prompt from the console, but I'd prefer to "simply" fix what's wrong. Like that guy, I need to repair the system rather than reinstall. System: Dell Inspiron 1525 Core 2 Duo Proprietary Driver for Broadcom 43xx wireless Dual-boot with Windows 7 (which is how I'm posting this, unfortunately I only have this machine and any experimenting requires constant reboots into Windows/brokenbuntu) Last package installed was Moonlight, but it appeared to install properly. Kernel: 2.6.32-25 Edit: After working with Karl's suggestions, it seems that the problem is with gdm. Error exit status 245 when attempting to sudo apt-get install --reinstall gdm, also an error processing gdm when running sudo apt-get -f install. How do I reinstall or repair gdm so that I can get back into my machine?

  Read the article

• How can I make my monitor run at it's native resolution under Kubuntu 9.10?

  - by Adam Matan

  Hi, I have installed Kubuntu 9.10 afresh on an HP desktop computer with a Samsung SyncMaster 2243 and Intel integrated graphics card. The screen resolution is fixed on 1280x1024 instead of the native 1680x1050, which makes my eyes bleed. $ lspci -k |grep "VGA" -A2 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10) Kernel driver in use: i915 Kernel modules: i915 and my xorg.conf: /etc/X11$ cat xorg.conf Section "Device" Identifier "Configured Video Device" Driver "vesa" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" EndSection Any ideas how to make this driver work? I found no working solutions on Google searches. Thanks, Adam

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >