Search Results

Search found 14780 results on 592 pages for 'low level'.

Page 82/592 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• Integrating Nagios with a ticketing system/incident mnagement system

  - by sektor

  Is there a free ticketing system/incident management system which will help me in achieving the following? 1) If a service goes down then Nagios alerts the on-duty staff and pushes the status to some backend or DB as a ticket, say the initial status is "New". 2) The on-duty staff logs in through a frontend and acknowledges the new ticket by marking it as "In progress", so now the status of the ticket changes from "New" to "In progress". 3) If even after "n" number of minutes no person from on-duty staff has changed the ticket status to "In progress" then Nagios alerts the next level of contacts. Although if the on-duty staff has acknowledged the ticket then there is no need to alert the next level. 4) When the service comes up Nagios closes the ticket by marking it "Closed" Now I already have Nagios monitoring set up and currently it alerts by sending text messages and mails, what I'm looking for is some framework which only escalates the issue(alerts the second level) if the first level(on-duty staff) fails to respond to the initial alert. By "responding to the alert" I mean, the on-duty staff can login via some frontend and basically change the status to something like "Acknowledged" or "In progress".

  Read the article

• OpenVPN server will not redirect traffic

  - by skerit

  I set up an OpenVPN server on my VPS, using this guide: http://vpsnoc.com/blog/how-to-install-openvpn-on-a-debianubuntu-vps-instantly/ And I can connect to it without problems. Connect, that is, because no traffic is being redirected. When I try to load a webpage when connected to the vpn I just get an error. This is the config file it generated: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca ca.crt cert server.crt key server.key dh dh1024.pem push "route 10.8.0.0 255.255.255.0" push "redirect-gateway" comp-lzo keepalive 10 60 ping-timer-rem persist-tun persist-key group daemon daemon This is my iptables.conf # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *raw :PREROUTING ACCEPT [37938267:10998335127] :OUTPUT ACCEPT [35616847:14165347907] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *nat :PREROUTING ACCEPT [794948:91051460] :POSTROUTING ACCEPT [1603974:108147033] :OUTPUT ACCEPT [1603974:108147033] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth1 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j MASQUERADE COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *mangle :PREROUTING ACCEPT [37938267:10998335127] :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616847:14165347907] :POSTROUTING ACCEPT [35680187:14169930490] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *filter :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616848:14165347947] -A INPUT -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A FORWARD -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 -A FORWARD -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A OUTPUT -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 COMMIT # Completed on Sat May 7 13:09:44 2011

  Read the article

• Best practice ACLs to prepare for auditors?

  - by Nic

  An auditor will be visiting our office soon, and they will require read-only access to our data. I have already created a domain user account and placed them into a group called "Auditors". We have a single fileserver (Windows Server 2008) with about ten shared folders. All of the shares are set up to allow full access to authenticated users, and access restrictions are implemented with NTFS ACL's. Most folders allow full access to the "Domain Users" group, but the auditor won't need to make any changes. It takes several hours to update NTFS ACL's since we have about one million files. Here are the options that I am currently considering. Create a "staff" group to assign read/write instead of "Domain Users" at the share level Create a "staff" group to assign read/write instead of "Domain Users" at the NTFS level Deny access to the "Auditors" group at the share level Deny access to the "Auditors" group at the NTFS level Accept the status quo and trust the auditor. I will probably need to configure similar users in the future, as some of our contractors require a domain account but shouldn't be able to modify our client data. Is there a best practice for this?

  Read the article

• Oracle Announces New Oracle Exastack Program for ISV Partners

  - by pfolgado

  Oracle Exastack Program Enables ISV Partners to Leverage a Scalable, Integrated Infrastructure to Deliver Their Applications Tuned and Optimized for High-Performance News Facts Enabling Independent Software Vendors (ISVs) and other members of Oracle Partner Network (OPN) to rapidly build and deliver faster, more reliable applications to end customers, Oracle today introduced Oracle Exastack Ready, available now, and Oracle Exastack Optimized, available in fall 2011 through OPN. The Oracle Exastack Program focuses on helping ISVs run their solutions on Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud -- integrated systems in which the software and hardware are engineered to work together. These products provide partners with a lower cost and high performance infrastructure for database and application workloads across on-premise and cloud based environments. Leveraging the new Oracle Exastack Program in which applications can qualify as Oracle Exastack Ready or Oracle Exastack Optimized, partners can use available OPN resources to optimize their applications to run faster and more reliably -- providing increased performance to their end users. By deploying their applications on Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud, ISVs can reduce the cost, time and support complexities typically associated with building and maintaining a disparate application infrastructure -- enabling them to focus more on their core competencies, accelerating innovation and delivering superior value to customers. After qualifying their applications as Oracle Exastack Ready, partners can note to customers that their applications run on and support Oracle Exadata Database Machine and Oracle Exalogic Elastic Cloud component products including Oracle Solaris, Oracle Linux, Oracle Database and Oracle WebLogic Server. Customers can be confident when choosing a partner's Oracle Exastack Optimized application, knowing it has been tuned by the OPN member on Oracle Exadata Database Machine or Oracle Exalogic Elastic Cloud with a goal of delivering optimum speed, scalability and reliability. Partners participating in the Oracle Exastack Program can also leverage their Oracle Exastack Ready and Oracle Exastack Optimized applications to advance to Platinum or Diamond level in OPN. Oracle Exastack Programs Provide ISVs a Reliable, High-Performance Application Infrastructure With the Oracle Exastack Program ISVs have several options to qualify and tune their applications with Oracle Exastack, including: Oracle Exastack Ready: Oracle Exastack Ready provides qualifying partners with specific branding and promotional benefits based on their adoption of Oracle products. If a partner application supports the latest major release of one of these products, the partner may use the corresponding logo with their product marketing materials: Oracle Solaris Ready, Oracle Linux Ready, Oracle Database Ready, and Oracle WebLogic Ready. Oracle Exastack Ready is available to OPN members at the Gold level or above. Additionally, OPN members participating in the program can leverage their Oracle Exastack Ready applications toward advancement to the Platinum or Diamond levels in the OPN Specialized program and toward achieving Oracle Exastack Optimized status. Oracle Exastack Optimized: When available, for OPN members at the Gold level or above, Oracle Exastack Optimized will provide direct access to Oracle technical resources and dedicated Oracle Exastack lab environments so OPN members can test and tune their applications to deliver optimal performance and scalability on Oracle Exadata Database Machine or Oracle Exalogic Elastic Cloud. Oracle Exastack Optimized will provide OPN members with specific branding and promotional benefits including the use of the Oracle Exastack Optimized logo. OPN members participating in the program will also be able to leverage their Oracle Exastack Optimized applications toward advancement to Platinum or Diamond level in the OPN Specialized program. Oracle Exastack Labs and ISV Enablement: Dedicated Oracle Exastack lab environments and related technical enablement resources (including Guided Learning Paths and Boot Camps) will be available through OPN for OPN members to further their knowledge of Oracle Exastack offerings, and qualify their applications for Oracle Exastack Optimized or Oracle Exastack Ready. Oracle Exastack labs will be available to qualifying OPN members at the Gold level or above. Partners are eligible to participate in the Oracle Exastack Ready program immediately, which will help them meet the requirements to attain Oracle Exastack Optimized status in the future. Guidelines for Oracle Exastack Optimized, as well as Oracle Exastack Labs will be available in fall 2011. Supporting Quotes "In order to effectively differentiate their software applications in the marketplace, ISVs need to rapidly deliver new capabilities and performance improvements," said Judson Althoff, Oracle senior vice president of Worldwide Alliances and Channels and Embedded Sales. "With Oracle Exastack, ISVs have the ability to optimize and deploy their applications with a complete, integrated and cloud-ready infrastructure that will help them accelerate innovation, unlock new features and functionality, and deliver superior value to customers." "We view performance as absolutely critical and a key differentiator," said Tom Stock, SVP of Product Management, GoldenSource. "As a leading provider of enterprise data management solutions for securities and investment management firms, with Oracle Exadata Database Machine, we see an opportunity to notably improve data processing performance -- providing high quality 'golden copy' data in a reduced timeframe. Achieving Oracle Exastack Optimized status will be a stamp of approval that our solution will provide the performance and scalability that our customers demand." "As a leading provider of Revenue Intelligence solutions for telecommunications, media and entertainment service providers, our customers continually demand more readily accessible, enriched and pre-analyzed information to minimize their financial risks and maximize their margins," said Alon Aginsky, President and CEO of cVidya Networks. "Oracle Exastack enables our solutions to deliver the power, infrastructure, and innovation required to transform our customers' business operations and stay ahead of the game." Supporting Resources Oracle PartnerNetwork (OPN) Oracle Exastack Oracle Exastack Datasheet Judson Althoff blog Connect with the Oracle Partner community at OPN on Facebook, OPN on LinkedIn, OPN on YouTube, or OPN on Twitter

  Read the article

• Searching for tasks with code – Executables and Event Handlers

  Searching packages or just enumerating through all tasks is not quite as straightforward as it may first appear, mainly because of the way you can nest tasks within other containers. You can see this illustrated in the sample package below where I have used several sequence containers and loops. To complicate this further all containers types, including packages and tasks, can have event handlers which can then support the full range of nested containers again. Towards the lower right, the task called SQL In FEL also has an event handler not shown, within which is another Execute SQL Task, so that makes a total of 6 Execute SQL Tasks 6 tasks spread across the package. In my previous post about such as adding a property expressionI kept it simple and just looked at tasks at the package level, but what if you wanted to find any or all tasks in a package? For this post I've written a console program that will search a package looking at all tasks no matter how deeply nested, and check to see if the name starts with "SQL". When it finds a matching task it writes out the hierarchy by name for that task, starting with the package and working down to the task itself. The output for our sample package is shown below, note it has found all 6 tasks, including the one on the OnPreExecute event of the SQL In FEL task TaskSearch v1.0.0.0 (1.0.0.0) Copyright (C) 2009 Konesans Ltd Processing File - C:\Projects\Alpha\Packages\MyPackage.dtsx MyPackage\FOR Counter Loop\SQL In Counter Loop MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL\OnPreExecute\SQL On Pre Execute for FEL SQL Task MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SEQ Nested Lvl 2\SQL In Nested Lvl 2 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #1 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #2 6 matching tasks found in package. The full project and code is available for download below, but first we can walk through the project to highlight the most important sections of code. This code has been abbreviated for this description, but is complete in the download. First of all we load the package, and then start by looking at the Executables for the package. // Load the package file Application application = new Application(); using (Package package = application.LoadPackage(filename, null)) { int matchCount = 0; // Look in the package's executables ProcessExecutables(package.Executables, ref matchCount); ... // // ... // Write out final count Console.WriteLine("{0} matching tasks found in package.", matchCount); } The ProcessExecutables method is a key method, as an executable could be described as the the highest level of a working functionality or container. There are several of types of executables, such as tasks, or sequence containers and loops. To know what to do next we need to work out what type of executable we are dealing with as the abbreviated version of method shows below. private static void ProcessExecutables(Executables executables, ref int matchCount) { foreach (Executable executable in executables) { TaskHost taskHost = executable as TaskHost; if (taskHost != null) { ProcessTaskHost(taskHost, ref matchCount); ProcessEventHandlers(taskHost.EventHandlers, ref matchCount); continue; } ... // // ... ForEachLoop forEachLoop = executable as ForEachLoop; if (forEachLoop != null) { ProcessExecutables(forEachLoop.Executables, ref matchCount); ProcessEventHandlers(forEachLoop.EventHandlers, ref matchCount); continue; } } } As you can see if the executable we find is a task we then call out to our ProcessTaskHost method. As with all of our executables a task can have event handlers which themselves contain more executables such as task and loops, so we also make a call out our ProcessEventHandlers method. The other types of executables such as loops can also have event handlers as well as executables. As shown with the example for the ForEachLoop we call the same ProcessExecutables and ProcessEventHandlers methods again to drill down into the hierarchy of objects that the package may contain. This code needs to explicitly check for each type of executable (TaskHost, Sequence, ForLoop and ForEachLoop) because whilst they all have an Executables property this is not from a common base class or interface. This example was just a simple find a task by its name, so ProcessTaskHost really just does that. We also get the hierarchy of objects so we can write out for information, obviously you can adapt this method to do something more interesting such as adding a property expression. private static void ProcessTaskHost(TaskHost taskHost, ref int matchCount) { if (taskHost == null) { return; } // Check if the task matches our match name if (taskHost.Name.StartsWith(TaskNameFilter, StringComparison.OrdinalIgnoreCase)) { // Build up the full object hierarchy of the task // so we can write it out for information StringBuilder path = new StringBuilder(); DtsContainer container = taskHost; while (container != null) { path.Insert(0, container.Name); container = container.Parent; if (container != null) { path.Insert(0, "\\"); } } // Write the task path // e.g. Package\Container\Event\Task Console.WriteLine(path); Console.WriteLine(); // Increment match counter for info matchCount++; } } Just for completeness, the other processing method we covered above is for event handlers, but really that just calls back to the executables. This same method is called in our main package method, but it was omitted for brevity here. private static void ProcessEventHandlers(DtsEventHandlers eventHandlers, ref int matchCount) { foreach (DtsEventHandler eventHandler in eventHandlers) { ProcessExecutables(eventHandler.Executables, ref matchCount); } } As hopefully the code demonstrates, executables (Microsoft.SqlServer.Dts.Runtime.Executable) are the workers, but within them you can nest more executables (except for task tasks).Executables themselves can have event handlers which can in turn hold more executables. I have tried to illustrate this highlight the relationships in the following diagram. Download Sample code project TaskSearch.zip (11KB)

  Read the article

• Searching for tasks with code – Executables and Event Handlers

  Searching packages or just enumerating through all tasks is not quite as straightforward as it may first appear, mainly because of the way you can nest tasks within other containers. You can see this illustrated in the sample package below where I have used several sequence containers and loops. To complicate this further all containers types, including packages and tasks, can have event handlers which can then support the full range of nested containers again. Towards the lower right, the task called SQL In FEL also has an event handler not shown, within which is another Execute SQL Task, so that makes a total of 6 Execute SQL Tasks 6 tasks spread across the package. In my previous post about such as adding a property expressionI kept it simple and just looked at tasks at the package level, but what if you wanted to find any or all tasks in a package? For this post I've written a console program that will search a package looking at all tasks no matter how deeply nested, and check to see if the name starts with "SQL". When it finds a matching task it writes out the hierarchy by name for that task, starting with the package and working down to the task itself. The output for our sample package is shown below, note it has found all 6 tasks, including the one on the OnPreExecute event of the SQL In FEL task TaskSearch v1.0.0.0 (1.0.0.0) Copyright (C) 2009 Konesans Ltd Processing File - C:\Projects\Alpha\Packages\MyPackage.dtsx MyPackage\FOR Counter Loop\SQL In Counter Loop MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL MyPackage\SEQ For Each Loop Wrapper\FEL Simple Loop\SQL In FEL\OnPreExecute\SQL On Pre Execute for FEL SQL Task MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SEQ Nested Lvl 2\SQL In Nested Lvl 2 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #1 MyPackage\SEQ Top Level\SEQ Nested Lvl 1\SQL In Nested Lvl 1 #2 6 matching tasks found in package. The full project and code is available for download below, but first we can walk through the project to highlight the most important sections of code. This code has been abbreviated for this description, but is complete in the download. First of all we load the package, and then start by looking at the Executables for the package. // Load the package file Application application = new Application(); using (Package package = application.LoadPackage(filename, null)) { int matchCount = 0; // Look in the package's executables ProcessExecutables(package.Executables, ref matchCount); ... // // ... // Write out final count Console.WriteLine("{0} matching tasks found in package.", matchCount); } The ProcessExecutables method is a key method, as an executable could be described as the the highest level of a working functionality or container. There are several of types of executables, such as tasks, or sequence containers and loops. To know what to do next we need to work out what type of executable we are dealing with as the abbreviated version of method shows below. private static void ProcessExecutables(Executables executables, ref int matchCount) { foreach (Executable executable in executables) { TaskHost taskHost = executable as TaskHost; if (taskHost != null) { ProcessTaskHost(taskHost, ref matchCount); ProcessEventHandlers(taskHost.EventHandlers, ref matchCount); continue; } ... // // ... ForEachLoop forEachLoop = executable as ForEachLoop; if (forEachLoop != null) { ProcessExecutables(forEachLoop.Executables, ref matchCount); ProcessEventHandlers(forEachLoop.EventHandlers, ref matchCount); continue; } } } As you can see if the executable we find is a task we then call out to our ProcessTaskHost method. As with all of our executables a task can have event handlers which themselves contain more executables such as task and loops, so we also make a call out our ProcessEventHandlers method. The other types of executables such as loops can also have event handlers as well as executables. As shown with the example for the ForEachLoop we call the same ProcessExecutables and ProcessEventHandlers methods again to drill down into the hierarchy of objects that the package may contain. This code needs to explicitly check for each type of executable (TaskHost, Sequence, ForLoop and ForEachLoop) because whilst they all have an Executables property this is not from a common base class or interface. This example was just a simple find a task by its name, so ProcessTaskHost really just does that. We also get the hierarchy of objects so we can write out for information, obviously you can adapt this method to do something more interesting such as adding a property expression. private static void ProcessTaskHost(TaskHost taskHost, ref int matchCount) { if (taskHost == null) { return; } // Check if the task matches our match name if (taskHost.Name.StartsWith(TaskNameFilter, StringComparison.OrdinalIgnoreCase)) { // Build up the full object hierarchy of the task // so we can write it out for information StringBuilder path = new StringBuilder(); DtsContainer container = taskHost; while (container != null) { path.Insert(0, container.Name); container = container.Parent; if (container != null) { path.Insert(0, "\\"); } } // Write the task path // e.g. Package\Container\Event\Task Console.WriteLine(path); Console.WriteLine(); // Increment match counter for info matchCount++; } } Just for completeness, the other processing method we covered above is for event handlers, but really that just calls back to the executables. This same method is called in our main package method, but it was omitted for brevity here. private static void ProcessEventHandlers(DtsEventHandlers eventHandlers, ref int matchCount) { foreach (DtsEventHandler eventHandler in eventHandlers) { ProcessExecutables(eventHandler.Executables, ref matchCount); } } As hopefully the code demonstrates, executables (Microsoft.SqlServer.Dts.Runtime.Executable) are the workers, but within them you can nest more executables (except for task tasks).Executables themselves can have event handlers which can in turn hold more executables. I have tried to illustrate this highlight the relationships in the following diagram. Download Sample code project TaskSearch.zip (11KB)

  Read the article

• Guidance: How to layout you files for an Ideal Solution

  - by Martin Hinshelwood

  Creating a solution and having it maintainable over time is an art and not a science. I like being pedantic and having a place for everything, no matter how small. For setting up the Areas to run Multiple projects under one solution see my post on  When should I use Areas in TFS instead of Team Projects and for an explanation of branching see Guidance: A Branching strategy for Scrum Teams. Update 17th May 2010 – We are currently trialling running a single Sprint branch to improve our history. Whenever I setup a new Team Project I implement the basic version control structure. I put “readme.txt” files in the folder structure explaining the different levels, and a solution file called “[Client].[Product].sln” located at “$/[Client]/[Product]/DEV/Main” within version control. Developers should add any projects you need to create to that solution in the format “[Client].[Product].[ProductArea].[Assembly]” and they will automatically be picked up and built automatically when you setup Automated Builds using Team Foundation Build. All test projects need to be done using MSTest to get proper IDE and Team Foundation Build integration out-of-the-box and be named for the assembly that it is testing with a naming convention of “[Client].[Product].[ProductArea].[Assembly].Tests” Here is a description of the folder layout; this content should be replicated in readme files under version control in the relevant locations so that even developers new to the project can see how to do it. Figure: The Team Project level - at this level there should be a folder for each the products that you are building if you are using Areas correctly in TFS 2010. You should try very hard to avoided spaces as these things always end up in a URL eventually e.g. "Code Auditor" should be "CodeAuditor". Figure: Product Level - At this level there should be only 3 folders (DEV, RELESE and SAFE) all of which should be in capitals. These folders represent the three stages of your application production line. Each of them may contain multiple branches but this format leaves all of your branches at the same level. Figure: The DEV folder is where all of the Development branches reside. The DEV folder will contain the "Main" branch and all feature branches is they are being used. The DEV designation specifies that all code in every branch under this folder has not been released or made ready for release. And feature branches MUST merge (Forward Integrate) from Main and stabilise prior to merging (Reverse Integration) back down into Main and being decommissioned. Figure: In the Feature branching scenario only merges are allowed onto Main, no development can be done there. Once we have a mature product it is important that new features being developed in parallel are kept separate. This would most likely be used if we had more than one Scrum team working on a single product. Figure: when we are ready to do a release of our software we will create a release branch that is then stabilised prior to deployment. This protects the serviceability of of our released code allowing developers to fix bugs and re-release an existing version. Figure: All bugs found on a release are fixed on the release.  All bugs found in a release are fixed on the release and a new deployment is created. After the deployment is created the bug fixes are then merged (Reverse Integration) into the Main branch. We do this so that we separate out our development from our production ready code.  Figure: SAFE or RTM is a read only record of what you actually released. Labels are not immutable so are useless in this circumstance.  When we have completed stabilisation of the release branch and we are ready to deploy to production we create a read-only copy of the code for reference. In some cases this could be a regulatory concern, but in most cases it protects the company building the product from legal entanglements based on what you did or did not release. Figure: This allows us to reference any particular version of our application that was ever shipped.   In addition I am an advocate of having a single solution with all the Project folders directly under the “Trunk”/”Main” folder and using the full name for the project folders.. Figure: The ideal solution If you must have multiple solutions, because you need to use more than one version of Visual Studio, name the solutions “[Client].[Product][VSVersion].sln” and have it reside in the same folder as the other solution. This makes it easier for Automated build and improves the discoverability of your code and its dependencies. Send me your feedback!   Technorati Tags: VS ALM,VSTS Developing,VS 2010,VS 2008,TFS 2010,TFS 2008,TFBS

  Read the article

• OpenSSL Versions in Solaris

  - by darrenm

  Those of you have have installed Solaris 11 or have read some of the blogs by my colleagues will have noticed Solaris 11 includes OpenSSL 1.0.0, this is a different version to what we have in Solaris 10.  I hope the following explains why that is and how it fits with the expectations on binary compatibility between Solaris releases. Solaris 10 was the first release where we included OpenSSL libraries and headers (part of it was actually statically linked into the SSH client/server in Solaris 9).  At time we were building and releasing Solaris 10 the current train of OpenSSL was 0.9.7.  The OpenSSL libraries at that time were known to not always be completely API and ABI (binary) compatible between releases (some times even in the lettered patch releases) though mostly if you stuck with the documented high level APIs you would be fine.   For this reason OpenSSL was classified as a 'Volatile' interface and in Solaris 10 Volatile interfaces were not part of the default library search path which is why the OpenSSL libraries live in /usr/sfw/lib on Solaris 10.  Okay, but what does Volatile mean ? Quoting from the attributes(5) man page description of Volatile (which was called External in older taxonomy): Volatile interfaces can change at any time and for any reason. The Volatile interface stability level allows Sun pro- ducts to quickly track a fluid, rapidly evolving specif- ication. In many cases, this is preferred to providing additional stability to the interface, as it may better meet the expectations of the consumer. The most common application of this taxonomy level is to interfaces that are controlled by a body other than Sun, but unlike specifications controlled by standards bodies or Free or Open Source Software (FOSS) communities which value interface compatibility, it can not be asserted that an incompatible change to the interface specifica- tion would be exceedingly rare. It may also be applied to FOSS controlled software where it is deemed more important to track the community with minimal latency than to provide stability to our customers. It also common to apply the Volatile classification level to interfaces in the process of being defined by trusted or widely accepted organization. These are generically referred to as draft standards. An "IETF Internet draft" is a well understood example of a specification under development. Volatile can also be applied to experimental interfaces. No assertion is made regarding either source or binary compatibility of Volatile interfaces between any two releases, including patches. Applications containing these interfaces might fail to function properly in any future release. Note that last paragraph!  OpenSSL is only one example of the many interfaces in Solaris that are classified as Volatile.  At the other end of the scale we have Committed (Stable in Solaris 10 terminology) interfaces, these include things like the POSIX APIs or Solaris specific APIs that we have no intention of changing in an incompatible way.  There are also Private interfaces and things we declare as Not-an-Interface (eg command output not intended for scripting against only to be read by humans). Even if we had declared OpenSSL as a Committed/Stable interface in Solaris 10 there are allowed exceptions, again quoting from attributes(5): 4. An interface specification which isn't controlled by Sun has been changed incompatibly and the vast majority of interface consumers expect the newer interface. 5. Not making the incompatible change would be incomprehensible to our customers. In our opinion and that of our large and small customers keeping up with the OpenSSL community is important, and certainly both of the above cases apply. Our policy for dealing with OpenSSL on Solaris 10 was to stay at 0.9.7 and add fixes for security vulnerabilities (the version string includes the CVE numbers of fixed vulnerabilities relevant to that release train).  The last release of OpenSSL 0.9.7 delivered by the upstream community was more than 4 years ago in Feb 2007. Now lets roll forward to just before the release of Solaris 11 Express in 2010. By that point in time the current OpenSSL release was 0.9.8 with the 1.0.0 release known to be coming soon.  Two significant changes to OpenSSL were made between Solaris 10 and Solaris 11 Express.  First in Solaris 11 Express (and Solaris 11) we removed the requirement that Volatile libraries be placed in /usr/sfw/lib, that means OpenSSL is now in /usr/lib, secondly we upgraded it to the then current version stream of OpenSSL (0.9.8) as was expected by our customers. In between Solaris 11 Express in 2010 and the release of Solaris 11 in 2011 the OpenSSL community released version 1.0.0.  This was a huge milestone for a long standing and highly respected open source project.  It would have been highly negligent of Solaris not to include OpenSSL 1.0.0e in the Solaris 11 release. It is the latest best supported and best performing version.     In fact Solaris 11 isn't 'just' OpenSSL 1.0.0 but we have added our SPARC T4 engine and the AES-NI engine to support the on chip crypto acceleration. This gives us 4.3x better AES performance than OpenSSL 0.9.8 running on AIX on an IBM POWER7. We are now working with the OpenSSL community to determine how best to integrate the SPARC T4 changes into the mainline OpenSSL.  The OpenSSL 'pkcs11' engine we delivered in Solaris 10 to support the CA-6000 card and the SPARC T1/T2/T3 hardware is still included in Solaris 11. When OpenSSL 1.0.1 and 1.1.0 come out we will asses what is best for Solaris customers. It might be upgrade or it might be parallel delivery of more than one version stream.  At this time Solaris 11 still classifies OpenSSL as a Volatile interface, it is our hope that we will be able at some point in a future release to give it a higher interface stability level. Happy crypting! and thank-you OpenSSL community for all the work you have done that helps Solaris.

  Read the article

• Siemens AG, Sector Healthcare, Increases Transparency and Improves Customer Loyalty with Web Portal Solution

  - by Kellsey Ruppel

  Siemens AG, Sector Healthcare, Increases Transparency and Improves Customer Loyalty with Web Portal Solution CUSTOMER AND PARTNER INFORMATION Customer Name – Siemens AG, Sector Healthcare Customer Revenue – 73,515 Billion Euro (2011, Siemens AG total) Customer Quote – “The realization of our complex requirements within a very short amount of time was enabled through the competent implementation partner Sapient, who fully used the  very broad scope of standard functionality provided in the Oracle WebCenter Portal, and the management of customer services, who continuously supported the project setup. ” – Joerg Modlmayr, Project Manager, Healthcare Customer Service Portal, Siemens AG The Siemens Healthcare Sector is one of the world's largest suppliers to the healthcare industry and a trendsetter in medical imaging, laboratory diagnostics, medical information technology and hearing aids. Siemens offers its customers products and solutions for the entire range of patient care from a single source – from prevention and early detection to diagnosis, and on to treatment and aftercare. By optimizing clinical workflows for the most common diseases, Siemens also makes healthcare faster, better and more cost-effective. To ensure greater transparency, increased efficiency, higher user acceptance, and additional services, Siemens AG, Sector Healthcare, replaced several existing legacy portal solutions that could not meet the company’s future needs with Oracle WebCenter Portal. Various existing portal solutions that cannot meet future demands will be successively replaced by the new central service portal, which will also allow for the efficient and intuitive implementation of new service concepts.  With Oracle, doctors and hospitals using Siemens medical solutions now have access to a central information portal that provides important information and services at just the push of a button.  Customer Name – Siemens AG, Sector Healthcare Customer URL – www.siemens.com Customer Headquarters – Erlangen, Germany Industry – Industrial Manufacturing Employees – 360,000  Challenges – Replace disparate medical service portals to meet future demands and eliminate an  unnecessarily high level of administrative work caused by heterogeneous installations Ensure portals meet current user demands to improve user-acceptance rates and increase number of total users Enable changes and expansion through standard functionality to eliminate the need for reliance on IT and reduce administrative efforts and associated high costs Ensure efficient and intuitive implementation of new service concepts for all devices and systems Ensure hospitals and clinics to transparently monitor and measure services rendered for the various medical devices and systems  Increase electronic interaction and expand services to achieve a higher level of customer loyalty Solution –  Deployed Oracle WebCenter Portal to ensure greater transparency, and as a result, a higher level of customer loyalty  Provided a centralized platform for doctors and hospitals using Siemens’ medical technology solutions that provides important information and services at the push of a button Reduced significantly the administrative workload by centralizing the solution in the new customer service portal Secured positive feedback from customers involved in the pilot program developed by design experts from Oracle partner Sapient. The interfaces were created with customer needs in mind. The first survey taken shortly after implementation came back with 2.4 points on a scale of 0-3 in the category “customer service portal intuitiveness level” Met all requirements including alignment with the Siemens Style Guide without extensive programming Implemented additional services via the portal such as benchmarking options to ensure the optimal use of the Customer Device Park Provided option for documentation of all services rendered in conjunction with the medical technology systems to ensure that the value of the services are transparent for the decision makers in the hospitals  Saved and stored all machine data from approximately 100,000 remote systems in the central service and information platform Provided the option to register errors online and follow the call status in real-time on the portal Made  available at the push of a button all information on the medical technology devices used in hospitals or clinics—from security checks and maintenance activities to current device statuses Provided PDF format Service Performance Reports that summarize information from periods of time ranging from previous weeks up to one year, meeting medical product law requirements  Why Oracle – Siemens AG favored Oracle for many reasons, however, the company ultimately decided to go with Oracle due to the enormous range of functionality the solutions offered for the healthcare sector.“We are not programmers; we are service providers in the medical technology segment and focus on the contents of the portal. All the functionality necessary for internet-based customer interaction is already standard in Oracle WebCenter Portal, which is a huge plus for us. Having Oracle as our technology partner ensures that the product will continually evolve, providing a strong technology platform for our customer service portal well into the future,” said Joerg Modlmayr project manager, Healthcare Customer Service Portal, Siemens AG. Partner Involvement – Siemens AG selected Oracle Partner Sapient because the company offered a service portfolio that perfectly met Siemens’ requirements and had a wealth of experience implementing Oracle WebCenter Portal. Additionally, Sapient had designers with a very high level of expertise in usability—an aspect that Siemens considered to be of vast importance for the project.  “The Sapient team completely met all our expectations. Our tightly timed project was completed on schedule, and the positive feedback from our users proves that we set the right measures in terms of usability—all thanks to the folks at Sapient,” Modlmayr said.  Partner Name – Sapient GmbH Deutschland Partner URL – www.sapient.com

  Read the article

• Project of Projects with team Foundation Server 2010

  - by Martin Hinshelwood

  It is pretty much accepted that you should use Areas instead of having many small Team Projects when you are using Team Foundation Server 2010. I have implemented this scenario many times and this is the current iteration of layout and considerations. If like me you work with many customers you will find that you get into a grove for how to set these things up to make them as easily understandable for everyone, while giving the best functionality. The trick is in making it as intuitive as possible for both you and the developers that need to work with it. There are five main places where you need to have the Product or Project name in prominence of any other value. Area Iteration Source Code Work Item Queries Build Once you decide how you are doing this in each of these places you need to keep to it religiously. Evan if you have one source code file to keep, make sure it is in the right place. This makes your developers and others working with the format familiar with where everything should go, as well as building up mussel memory. This prevents the neat system degenerating into a nasty mess. Areas Areas are traditionally used to separate out parts of your product / project so that you can see how much effort has gone into each. Figure: The top level areas are for reporting and work item separation There are massive advantages of using this method. You can: move work from one project to another rename a project / product It is far more likely that a project or product gets renamed than a department. Tip: If you have many projects, over 100, you should consider categorising them here, but make sure that the actual project name always sits at the same level so you know which is which. Figure: Always keep things that are the same at the same level Note: You may use these categories only at the Area/Iteration level to make it easier to select on drop down lists. You may not want to use them everywhere. On the other hand, for consistency it would be better to. Iterations Iterations are usually used to some sort of time based consideration. Here I am splitting into Iterations with periodic releases. Figure: Each product needs to be able to have its own cadence The ability to have each project run at its own pace and to enable them to have their own release schedule is often of paramount importance and you don’t want to fix your 100+ projects to all be released on the same date. Source Code Having a good structure for your source even if you are not branching or having multiple products under the same structure is always a good idea. Figure: Separate out your products source You need to think about both your branches as well as the structure of your source. All your code should be under “Source” and everything you need to build your solution including Build Scripts and 3rd party tools should be under your “Main” (branch) folder. This should them be branched by “Quality”, “Release” or both to get the most out of your branching structure. The important thing is to make sure you branch (or be able to branch) everything you need to build, test and deploy your application to an environment. That environment may be development, test or even production, but I can’t stress the importance of having everything your need. Note: You usually will not be able to install custom software on your build server. Store any *.dll’s or *.exe’s that you need under the “Tools\Tool1” folder. Note: Consult the Branching Guidance for Team Foundation Server 2010 for more on branching Figure: Adding category may be a necessary evil Even if you have to have a couple of categories called “Default”, it is better than not knowing the difference between a folder, Product and Branch. Work Item Queries Queries are used to load lists of Work Items out of TFS so you can see what work you have. This means that you want to also separate queries out by Product / project to make it easier to Figure: Again you have the same first level structure Having Folders also in Work Item Tracking we do the same thing. We put all the queries under a folder named for the Product / Project and change each query to have “AreaPath=[TeamProject]\[ProductX]” in the query instead of the standard “Project=@Project”. Tip: Don’t have a folder with new queries for each iteration. Instead have a single “Current” folder that has queries that point to the current iteration. Just change the queries as you move from one iteration to another. Tip: You can ctrl+drag the “Product1” folder to create your “Product2” folder. Builds You may have many builds both for individual products but also for different quality's. This can be further complicated by having some builds that action “Gated Check-In” and others that are specifically for “Release”, “Test” or another purpose. Figure: There are no folders, yet, for the builds so you need a good naming convention Its a pity that there are no folders under builds, some way to categorise would be nice. In lue of that at the moment you can use a functional naming convention that at least allows you to find what you want. Conclusion It is really easy to both achieve and to stick to this format if you take the time to do it. Unless you have 1000+ builds or 100+ Products you are unlikely run into any issues. Even then there are things you can do to mitigate the issues and I have describes some of them above. Let me know if you can think of any other things to make this easier.

  Read the article

• Performance triage

  - by Dave

  Folks often ask me how to approach a suspected performance issue. My personal strategy is informed by the fact that I work on concurrency issues. (When you have a hammer everything looks like a nail, but I'll try to keep this general). A good starting point is to ask yourself if the observed performance matches your expectations. Expectations might be derived from known system performance limits, prototypes, and other software or environments that are comparable to your particular system-under-test. Some simple comparisons and microbenchmarks can be useful at this stage. It's also useful to write some very simple programs to validate some of the reported or expected system limits. Can that disk controller really tolerate and sustain 500 reads per second? To reduce the number of confounding factors it's better to try to answer that question with a very simple targeted program. And finally, nothing beats having familiarity with the technologies that underlying your particular layer. On the topic of confounding factors, as our technology stacks become deeper and less transparent, we often find our own technology working against us in some unexpected way to choke performance rather than simply running into some fundamental system limit. A good example is the warm-up time needed by just-in-time compilers in Java Virtual Machines. I won't delve too far into that particular hole except to say that it's rare to find good benchmarks and methodology for java code. Another example is power management on x86. Power management is great, but it can take a while for the CPUs to throttle up from low(er) frequencies to full throttle. And while I love "turbo" mode, it makes benchmarking applications with multiple threads a chore as you have to remember to turn it off and then back on otherwise short single-threaded runs may look abnormally fast compared to runs with higher thread counts. In general for performance characterization I disable turbo mode and fix the power governor at "performance" state. Another source of complexity is the scheduler, which I've discussed in prior blog entries. Lets say I have a running application and I want to better understand its behavior and performance. We'll presume it's warmed up, is under load, and is an execution mode representative of what we think the norm would be. It should be in steady-state, if a steady-state mode even exists. On Solaris the very first thing I'll do is take a set of "pstack" samples. Pstack briefly stops the process and walks each of the stacks, reporting symbolic information (if available) for each frame. For Java, pstack has been augmented to understand java frames, and even report inlining. A few pstack samples can provide powerful insight into what's actually going on inside the program. You'll be able to see calling patterns, which threads are blocked on what system calls or synchronization constructs, memory allocation, etc. If your code is CPU-bound then you'll get a good sense where the cycles are being spent. (I should caution that normal C/C++ inlining can diffuse an otherwise "hot" method into other methods. This is a rare instance where pstack sampling might not immediately point to the key problem). At this point you'll need to reconcile what you're seeing with pstack and your mental model of what you think the program should be doing. They're often rather different. And generally if there's a key performance issue, you'll spot it with a moderate number of samples. I'll also use OS-level observability tools to lock for the existence of bottlenecks where threads contend for locks; other situations where threads are blocked; and the distribution of threads over the system. On Solaris some good tools are mpstat and too a lesser degree, vmstat. Try running "mpstat -a 5" in one window while the application program runs concurrently. One key measure is the voluntary context switch rate "vctx" or "csw" which reflects threads descheduling themselves. It's also good to look at the user; system; and idle CPU percentages. This can give a broad but useful understanding if your threads are mostly parked or mostly running. For instance if your program makes heavy use of malloc/free, then it might be the case you're contending on the central malloc lock in the default allocator. In that case you'd see malloc calling lock in the stack traces, observe a high csw/vctx rate as threads block for the malloc lock, and your "usr" time would be less than expected. Solaris dtrace is a wonderful and invaluable performance tool as well, but in a sense you have to frame and articulate a meaningful and specific question to get a useful answer, so I tend not to use it for first-order screening of problems. It's also most effective for OS and software-level performance issues as opposed to HW-level issues. For that reason I recommend mpstat & pstack as my the 1st step in performance triage. If some other OS-level issue is evident then it's good to switch to dtrace to drill more deeply into the problem. Only after I've ruled out OS-level issues do I switch to using hardware performance counters to look for architectural impediments.

  Read the article

• SQL Server - Rebuilding Indexes

  - by Renso

  Goal: Rebuild indexes in SQL server. This can be done one at a time or with the example script below to rebuild all index for a specified table or for all tables in a given database. Why? The data in indexes gets fragmented over time. That means that as the index grows, the newly added rows to the index are physically stored in other sections of the allocated database storage space. Kind of like when you load your Christmas shopping into the trunk of your car and it is full you continue to load some on the back seat, in the same way some storage buffer is created for your index but once that runs out the data is then stored in other storage space and your data in your index is no longer stored in contiguous physical pages. To access the index the database manager has to "string together" disparate fragments to create the full-index and create one contiguous set of pages for that index. Defragmentation fixes that. What does the fragmentation affect?Depending of course on how large the table is and how fragmented the data is, can cause SQL Server to perform unnecessary data reads, slowing down SQL Server’s performance.Which index to rebuild?As a rule consider that when reorganize a table's clustered index, all other non-clustered indexes on that same table will automatically be rebuilt. A table can only have one clustered index.How to rebuild all the index for one table:The DBCC DBREINDEX command will not automatically rebuild all of the indexes on a given table in a databaseHow to rebuild all indexes for all tables in a given database:USE [myDB]    -- enter your database name hereDECLARE @tableName varchar(255)DECLARE TableCursor CURSOR FORSELECT table_name FROM information_schema.tablesWHERE table_type = 'base table'OPEN TableCursorFETCH NEXT FROM TableCursor INTO @tableNameWHILE @@FETCH_STATUS = 0BEGINDBCC DBREINDEX(@tableName,' ',90)     --a fill factor of 90%FETCH NEXT FROM TableCursor INTO @tableNameENDCLOSE TableCursorDEALLOCATE TableCursorWhat does this script do?Reindexes all indexes in all tables of the given database. Each index is filled with a fill factor of 90%. While the command DBCC DBREINDEX runs and rebuilds the indexes, that the table becomes unavailable for use by your users temporarily until the rebuild has completed, so don't do this during production  hours as it will create a shared lock on the tables, although it will allow for read-only uncommitted data reads; i.e.e SELECT.What is the fill factor?Is the percentage of space on each index page for storing data when the index is created or rebuilt. It replaces the fill factor when the index was created, becoming the new default for the index and for any other nonclustered indexes rebuilt because a clustered index is rebuilt. When fillfactor is 0, DBCC DBREINDEX uses the fill factor value last specified for the index. This value is stored in the sys.indexes catalog view. If fillfactor is specified, table_name and index_name must be specified. If fillfactor is not specified, the default fill factor, 100, is used.How do I determine the level of fragmentation?Run the DBCC SHOWCONTIG command. However this requires you to specify the ID of both the table and index being. To make it a lot easier by only requiring you to specify the table name and/or index you can run this script:DECLARE@ID int,@IndexID int,@IndexName varchar(128)--Specify the table and index namesSELECT @IndexName = ‘index_name’    --name of the indexSET @ID = OBJECT_ID(‘table_name’)  -- name of the tableSELECT @IndexID = IndIDFROM sysindexesWHERE id = @ID AND name = @IndexName--Show the level of fragmentationDBCC SHOWCONTIG (@id, @IndexID)Here is an example:DBCC SHOWCONTIG scanning 'Tickets' table...Table: 'Tickets' (1829581556); index ID: 1, database ID: 13TABLE level scan performed.- Pages Scanned................................: 915- Extents Scanned..............................: 119- Extent Switches..............................: 281- Avg. Pages per Extent........................: 7.7- Scan Density [Best Count:Actual Count].......: 40.78% [115:282]- Logical Scan Fragmentation ..................: 16.28%- Extent Scan Fragmentation ...................: 99.16%- Avg. Bytes Free per Page.....................: 2457.0- Avg. Page Density (full).....................: 69.64%DBCC execution completed. If DBCC printed error messages, contact your system administrator.What's important here?The Scan Density; Ideally it should be 100%. As time goes by it drops as fragmentation occurs. When the level drops below 75%, you should consider re-indexing.Here are the results of the same table and clustered index after running the script:DBCC SHOWCONTIG scanning 'Tickets' table...Table: 'Tickets' (1829581556); index ID: 1, database ID: 13TABLE level scan performed.- Pages Scanned................................: 692- Extents Scanned..............................: 87- Extent Switches..............................: 86- Avg. Pages per Extent........................: 8.0- Scan Density [Best Count:Actual Count].......: 100.00% [87:87]- Logical Scan Fragmentation ..................: 0.00%- Extent Scan Fragmentation ...................: 22.99%- Avg. Bytes Free per Page.....................: 639.8- Avg. Page Density (full).....................: 92.10%DBCC execution completed. If DBCC printed error messages, contact your system administrator.What's different?The Scan Density has increased from 40.78% to 100%; no fragmentation on the clustered index. Note that since we rebuilt the clustered index, all other index were also rebuilt.

  Read the article

• How to set 2 conditions / criterias for VLOOKUP / LOOKUP / etc in OpenOffice Calc (or Excel)

  - by MestreLion

  I have this spreadsheet that started as a silly aid for a game (Mafia Wars 2), but grew into a tricky spreadsheet question. In the game your character have 9 "slots" for weapons and armors, 1 for each "type": Light Weapon, Heavy Weapon, Body Armor, Head Armor, etc. So I made a list of all weapons and armors available in the game, 1 item per row. Example: SHOP ITEM TYPE ITEM NAME ATK DEF PRICE EQUIPPED? Marketplace Weapon Light Konrad Knife 16 5 5.500 Marketplace Weapon Light Ice Queen 19 6 8.200 Marketplace Armor Body Up Layered Polym 0 31 8.600 Marketplace Armor Body Up Full Shield 7 42 17.650 Marketplace Weapon Heavy Konrad Bullpup 53 25 24.500 Marketplace Weapon Heavy Full Moon Blow 73 12 24.500 x Marketplace Armor Body Low Knee Pads 17 26 14.200 x Marketplace Armor Body Low Army Boots 15 55 24.500 Bone Yard Weapon Light Bone Launcher 41 2 9.400 x Neon Strip Vehicle Ground Supercharged 41 34 24.500 Dead End Weapon Heavy Sharp Sickle 21 5 24.500 Dead End Armor Body Low Unholy Boots 5 36 15.000 Dead End Armor Head Hockey Mask 5 18 15.900 x Last columns is an indication of the items i have already bought and equipped (marked with "x"). What I need is a formula that, for each "slot" (item type), returns info related to the item of that kind that I am using. That would be: ITEM TYPE SHOP NAME ITEM NAME ATK DEF PRICE Weapon Light Bone Yard Bone Launcher 41 2 9.400 Weapon Heavy Marketplace Full Moon Blow 73 12 24.500 Weapon Special -- -- -- -- -- Armor Body Up -- -- -- -- -- Armor Body Low Marketplace Knee Pads 17 26 14.200 Armor Head Dead End Hockey Mask 5 18 15.900 Vehicle Ground -- -- -- -- -- Vehicle Water -- -- -- -- -- Vehicle Air -- -- -- -- -- The item types are fixed, so they can be hard coded. Each row for an item type. So, for 1st result line, it would return data from the row where both 2nd column is "Weapon Light" and last column is "x". Basically I need a LOOKUP (or VLOOKUP, or anything else) that uses 2 criteria to find a given row, the item type and the X marker. Question is: HOW? I am using OpenOffice Calc 3.2.1, but since it shares so many functions with MS Excel, answers for Excel are also fine (as long as it only uses regular formulas, no VBScript or Macros or VBA etc) Last but not least, suggestions / solutions for rearranging the data so it makes this problem easier to solve are also welcome. Thanks!

  Read the article

• Satellite data in Russia?

  - by Eddy

  Anyone familiar with options for transmitting data in Russia? I'd be interested in hearing about low-speed packet data and faster. Not really looking at VSAT initially as I'd like to keep the power requirements low unless we find no other options.

  Read the article

• How to stop switchable graphics from switching to high-power GPU when charging the laptop?

  - by Saifallah

  I've an Acer laptop with Windows 7 64 bit and an ATI Radeon HD 6550M Graphics card. Whenever I connect the power to charge the battery it automatically switches to the high-power GPU (ATI) instead of the low-power (Intel) GPU. There's an option in the bios to stop such thing but it makes the GPU runs always on high-power and I can't switch to the low-power GPU. How can I prevent the switchable graphics from automatically using the high-power GPU when charging?

  Read the article

• Linux server very slow after IP change and synflood attack

  - by Johannes Ruof

  our server experienced a synflood attack and we used the csf firewall synflood settings to block it. Our server administrators also changed the IP of the server to a new one and blackholed the old IP. The attack went over and I changed the synflood settings back. However the server is still very slow, with a very low CPU usage and very low traffic on the website. Does anybody have an idea what might be causing this? The server is a CENTOS 6.4 x86_64 Thanks in advance, J. Ruof

  Read the article

• How can order of IP addresses issued be controlled?

  - by warren

  Every home router I've setup/used issues addresses from low to high. However, dhcpd from the Internet Systems Consortium seems to issue addresses in reverse order - ie, high to low. Is there a way to change this so that addresses are issued starting at the bottom of the range, and progress higher?

  Read the article

• Clamdscan scans file in 0 seconds

  - by SupaCoco

  I have to run clamav on large files. I was wondering which command was the fastest between clamscan and clamdscan. But it seems that clamdscan is not working properly: it scans file larger than 1 GB. Could you guys help me find why the heck clamdscan isn't working ? Between clamscan and clamdscan which one is less resource consuming ? I run ClamAV 0.97.8/18037 on Ubuntu 12.04.3 LTS. Please find below the execution result of both commands: clamscan myfile.zip ----------- SCAN SUMMARY ----------- Known viruses: 2864504 Engine version: 0.97.8 Scanned directories: 0 Scanned files: 1 Infected files: 0 Data scanned: 0.00 MB Data read: 1024.16 MB (ratio 0.00:1) Time: 9.145 sec (0 m 9 s) clamdscan myfile.zip /home/ubuntu/workspace/benchmark/myfile.zip: OK ----------- SCAN SUMMARY ----------- Infected files: 0 Time: 0.000 sec (0 m 0 s) And here are the clamav log file: Wed Oct 30 10:26:32 2013 -> Received POLLIN|POLLHUP on fd 4 Wed Oct 30 10:26:32 2013 -> Got new connection, FD 9 Wed Oct 30 10:26:32 2013 -> Received POLLIN|POLLHUP on fd 5 Wed Oct 30 10:26:32 2013 -> fds_poll_recv: timeout after 5 seconds Wed Oct 30 10:26:32 2013 -> Received POLLIN|POLLHUP on fd 9 Wed Oct 30 10:26:32 2013 -> got command CONTSCAN /home/ubuntu/workspace/benchmark/myfile.zip (51, 7), argument: /home/ubuntu/workspace/benchmark/myfile.zip Wed Oct 30 10:26:32 2013 -> mode -> MODE_WAITREPLY Wed Oct 30 10:26:32 2013 -> Breaking command loop, mode is no longer MODE_COMMAND Wed Oct 30 10:26:32 2013 -> Consumed entire command Wed Oct 30 10:26:32 2013 -> Number of file descriptors polled: 1 fds Wed Oct 30 10:26:32 2013 -> fds_poll_recv: timeout after 3600 seconds Wed Oct 30 10:26:32 2013 -> THRMGR: queue (single) crossed low threshold -> signaling Wed Oct 30 10:26:32 2013 -> THRMGR: queue (bulk) crossed low threshold -> signaling Wed Oct 30 10:26:32 2013 -> /home/ubuntu/workspace/benchmark/myfile.zip: OK Wed Oct 30 10:26:32 2013 -> Finished scanthread Wed Oct 30 10:26:32 2013 -> Scanthread: connection shut down (FD 9) Wed Oct 30 10:26:32 2013 -> THRMGR: queue (single) crossed low threshold -> signaling Wed Oct 30 10:26:32 2013 -> THRMGR: queue (bulk) crossed low threshold -> signaling

  Read the article

• Laptop will boot to some usb flash drives but not others.

  - by evolvd

  Laptop: HP Compaq 6710b I can boot from usb just fine with the following usb flash drives: Cruzer micro 4GB HP 4GB The flash drive that will not boot: Flash Voyager 8GB To knock out variables I did the following: Using Hard Disk Low Level Format Tool I performed a low level format Full erase with Flash Memory Tookit In windows 7 I formated the drive to fat32 Used USB-Boot-Tester to write to the drive Also used uNetbooting with various distros to see if that would make a difference My guesses on what could be preventing the drive from booting: The laptop does not support booting to usb flash drives larger than 4GB The drive is defective in some way

  Read the article

• Stopping windows changing colour scheme

  - by dave

  Windows keeps saying my computer is low on memory and changing the aero scheme to basic its really annoying I have 16gb of ram and 2 3gb 6970 gpu's i have no issues at all with anything expect from this my motherboard has a intel hd onboard gpu i think its something to do with this but all my settings are correct. Is there anyway to tell it not to change it without asking me or to tell it how much memory is too low its driving me mad.

  Read the article

• Set up Ubuntu to boot in Terminal mode with all service running.

  - by Darkmage

  Im running a virtual linux server on a low-end system, and i wold like to configure the server to boot in terminal window and not to the Gnome log in window, this is because of the low specs on the hardware.

  Read the article

• How do I limit the memory usage of a specific process in linux?

  - by user20222

  I've written a program for a class that my professor will be testing in various low memory environments to see how it behaves when the program runs out of memory. Is there a way I can simulate the execution in a low memory environment without creating a virtual machine?

  Read the article

• How to change user for more rights on a SFTP client?

  - by Zenklys

  It is always suggested on first step to disable the remote root login for the SSH protocol. I have a low-right user able to connect via SSH and once connected, I simply su in order to gain more rights. Now when using a sFTP client, I use my low-right user and am thus able to do next to nothing. My question is : Is it possible to change user after login using 3rd party client, such as Transmit, Cyberduck, Filezilla ? PS : Mac clients would be great ;)

  Read the article

• iSCSI NAS supporting VMware Esxi 5.1 servers in a software development environment

  - by BigTFromAZ

  I would like to build (or purchase) the smallest, quietest most energy efficient servers that I can for a low demand environment. These would only have a small disk for guest swap files, a CPU (XEON preferred), 32 Gb of memory and minimal graphics. The virtual machines need to be up but demand will be quite low. Any thought on case, format processors, fans, motherboard, et al? Small, quiet and lots of RAM are the operative words here.

  Read the article

• Can a SQL Server have a CPU bottleneck when Processor Time is under 30%

  - by Sleepless

  Is it in principle possible for the CPU to be the bottleneck on a SQL Server if the Performance Counter Processor:Processor Time is constantly under 30% on all cores? Or does low Processor Time automatically allow me to rule out the CPU as a potential trouble source? I am asking this because SQL Nexus lists CPU as the top bottleneck on a server with low Processor Time values.

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >