Search Results

Search found 4477 results on 180 pages for 'wireless keyboards'.

Page 82/180 | < Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

• windows server 2008 r2 remote desktop issue with roaming clients

  - by Patrick D'Haese

  I have the following situation : a Dell windows server 2008 R2 computer, with remote desktop services installed. I have installed a java application making use of a PostgreSql database, and made this application available for clients using RDP. Clients are standard Win XP pc's and Psion Neo handheld devices running Windows CE 5 Pro. The application works fine for clients on standard XP pc's connected directly via cat 5E Ethernet cable to a Dell Powerconnect 2816 switch. The Psion Neo clients connect wireless to the network via Motorola AP6532 access points. These access points are connected via a POE adapter to the same switch as the XP pc's. The Psion devices can connect without any problem and very quickly to the server and to the application using RDP. So far, so good. When the Psion devices move around in the warehouse, and they roam from one access point to the other, the RDP session on the client freezes for approx 1 minute, and then it automatically resumes the session. This freezing is very annoying for the users. Can anyone help in solving this issue? Update (August 9) : After re-installing the access points we have a working situation, but only when connecting to the RDP host : * via a Win Xp SP3 laptop * via a Symbol MC9190 Win CE 6 mobile device When roaming we notice a small hick-up less then 1 second, what is very acceptable. With the Psion NEO it's still not working, when roaming the screen freezes from 2 to 30 seconds. The RDP client on the win xp sp3 laptop and the symbol mc9190 is version 6.0. The RDP client on the neo is version 5.2. I have changed the security layer on the RDP host to RDP security layer (based on forums on the internet), because older RDP clients seem to have issues with the RDP 7.1 protocol on the Win server 2088 R2. Psion adviced us to do some network logging activity on the different devices. We made this logging via wireshark, and based on this the conclusion of Psion is that the server fails in handling tcp-requests. Can anyone give me a second opinion by analysing the wireshark loggings. Thanks in advance. Regards Patrick

  Read the article

• How can I combine the input of two Keyboards?

  - by Janusz

  I use a Stinkyboard Footboard to enter shortcuts with my feet on my mac. This works fine, the Footboard is recognized as another USB keyboard and the shortcuts are working. One thing that is not working is to assign two Keys like ALT + SHIFT to the foot pedal and then add another key like 1 with the keyboard I use with my hands. Is there a way to make this two keyboards combine its input into one shortcut?

  Read the article

• How to make Windows 7 use the internet connection that I specify

  - by user138957

  I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Why does pinging a local router return "Destination Host Unreachable"?

  - by Matt H

  I have two tomato routers. One is bridged wirelessly with the other. I have a new server on the network. It's running Ubuntu Server 11.04. They are all connected like this: A - Linux PC B - New Server C - Mac Mini D - Macbook T1 - Tomato 1 T2 - Tomato 2 They are connected like so: A -----+-T1 ==== wireless bridge ==== T2----- ADSL modem | | C & D Connected wirelessly to T2 B -----+ A, C & D do not experience any issues. I have an active SSH session to B from A and it's not experiencing any loss. B, the new server occasionally cannot ping T2 and therefore cannot connect to the internet. However, A can always contact B and B can ping A and B When the network is lost, B can still ping T1, but not T2 yet at the same as B has lost connection to T2, A can still ping T2. Any ideas on what this could be? there is nothing that gives any clues in any of the logs on either router or the linux server. One thing that is interesting is that I set up a ping running between B and T2. T2 has the IP address 192.68.1.1 Here is what I am seeing: From 192.168.1.1 icmp_seq=26 Destination Host Unreachable From 192.168.1.1 icmp_seq=27 Destination Host Unreachable From 192.168.1.1 icmp_seq=28 Destination Host Unreachable From 192.168.1.1 icmp_seq=29 Destination Host Unreachable From 192.168.1.1 icmp_seq=30 Destination Host Unreachable From 192.168.1.1 icmp_seq=31 Destination Host Unreachable From 192.168.1.1 icmp_seq=33 Destination Host Unreachable From 192.168.1.1 icmp_seq=34 Destination Host Unreachable From 192.168.1.1 icmp_seq=35 Destination Host Unreachable 64 bytes from 192.168.1.1: icmp_req=36 ttl=63 time=3.40 ms 64 bytes from 192.168.1.1: icmp_req=37 ttl=63 time=5.70 ms 64 bytes from 192.168.1.1: icmp_req=38 ttl=63 time=2.25 ms 64 bytes from 192.168.1.1: icmp_req=39 ttl=63 time=2.18 ms 64 bytes from 192.168.1.1: icmp_req=40 ttl=63 time=3.12 ms 64 bytes from 192.168.1.1: icmp_req=41 ttl=63 time=2.15 ms 64 bytes from 192.168.1.1: icmp_req=42 ttl=63 time=1.97 ms 64 bytes from 192.168.1.1: icmp_req=43 ttl=63 time= And it cycles to being reachable and not. So I guess you could say the question is, why is the router responding that it cannot be reached?

  Read the article

• whats the difference between 101 and 102 key keyboards, and which do i need for UK laptop

  - by Tom

  I want to replace the US keyboard on my laptop with a UK one. I thought that UK keyboards were 102 and US were 101 as my Uk one has a (#) key and the US one doesn't. But the UK replacement part keyboard specifies 101 keys, so I am now confused. Can someone set me straight on this...!

  Read the article

• Weird Network Behavior of Home Router

  - by Stilgar

  First of all I would like to apologize because what you are going to read will be long and confusing but I am fighting this issue for 3 days now and am out of ideas. At home I have the following setup 50Mbps Internet connects into a home router A 2 desktop computers connect to router A via standard FTP LAN cables including one where the cable is ~20m long. a second router B connects to router A via standard FTP LAN cable X (~20m long). several devices connect to the wireless network of router B and there are a couple of desktop computers connected to it through FTP LAN cables. For some reason computers connected to router B when it is connected via cable X have very slow Internet connection. It is like 5 times slower than what is expected. This is the actual problem I am trying to solve. Interesting facts If a computer is connected to cable X directly instead of through router B the Internet speed is just fine (up to the 50Mbps I get from the ISP). Tested with two computers. I have tried replacing router B with another router C and the problem persists. If I connect router B via another cable to the same ports with the same settings everything seems to work fine and computers connected to router B have quite fast Internet I have tested mainly via Speedtest.net but I have also achieved similar speeds when downloading a file The upload speed is quite higher than the download speed in all cases. Note that my ISP usually has higher upload speed (unless it manages to hit the 50Mbps cap) It seems like the speed when connecting through router B with cable X is reduced 4-5 times no matter what the original speed is. For example via router B I get 10Mbps speed to local servers where I get 50Mbps when connected on router A. If I use a distant server where the ISP is only able to provide 25Mbps I get 4-5Mbps on router B. WiFi is slower than LAN on both routers (which is normal) but the reduced speed is reduced proportionally for WiFi. In addition the upload speed is normally higher from the ISP and it is also reduced proportionally. I have tried two different network configurations. One where I have NAT behind NAT where router B connects to router A via the WAN port and has its own DHCP. Second where router B connects to router A via standard LAN port and has DHCP disabled. In this configuration router B serves as a switch and the Network Gateway for computers connected to router B is the internal IP address of router A. Both configurations work just fine but both manifest the reduced speed issue. pings seem to work just fine As far as I can tell none of the cables is crossed The RJ45 setup for cable X orange orange-white brown brow-white blue blue-white green green-white This is a big problem for me since cable X passes through walls and floors and is very hard to replace. I also may have gotten some of the facts wrong because I am almost going crazy with this issue and testing includes going several floors up and down the staircase. One hypothesis I came up with is that the cable is defective in such a way that the voltage from the router affects its performance. When it is connected to a computer it performs just fine but the router has less power. Related hypothesis includes the cable being affected by electricity cables in the walls when the voltage is low. (I know nothing about electricity) So any ideas what to do, what to test or what the issue may be?

  Read the article

• Prepaid UMTS/HSDPA Internet in Israel

  - by user309305

  Can someone recommend a cheap wireless internet carrier in Israel? I would prefer a prepaid plan.

  Read the article

• Wi-Fi Stick with ZD1211 chip refuses to work on Ubuntu >8.10. No clue.

  - by Benjamin Maus

  I have a machine running Ubuntu 9.10 (Karmic *x86_64*). Everything is running smooth so far, except for the Wi-Fi USB Stick. The same device worked perfectly in 8.10. The wireless device is a GW-US54GXS using the Zydas Zd1211 chipset. Dmesg output after plugging in: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' [ 196.304209] zd1211rw 2-1:1.0: phy0 [ 196.304227] usbcore: registered new interface driver zd1211rw [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Syslog output: Nov 5 11:20:24 somesystem kernel: [ 196.303436] phy0: Selected rate control algorithm 'minstrel' Nov 5 11:20:24 kierkegaard NetworkManager: <info> Found radio killswitch rfkill0 (at /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/ieee80211/phy0/rfkill0) (driver <unknown>) Nov 5 11:20:24 somesystem kernel: [ 196.304209] zd1211rw 2-1:1.0: phy0 Nov 5 11:20:24 somesystem kernel: [ 196.304227] usbcore: registered new interface driver zd1211rw Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wmaster0, iface: wmaster0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: devices added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0) Nov 5 11:20:24 somesystem NetworkManager: SCPlugin-Ifupdown: device added (path: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/net/wlan0, iface: wlan0): no ifupdown configuration found. Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): new 802.11 WiFi device (driver: 'zd1211rw') Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/2 Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): now managed Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): device state change: 1 -> 2 (reason 2) Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): bringing up device. Nov 5 11:20:24 somesystem kernel: [ 196.334137] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.357463] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:24 somesystem kernel: [ 196.402643] zd1211rw 2-1:1.0: firmware version 4725 Nov 5 11:20:24 somesystem kernel: [ 196.442611] zd1211rw 2-1:1.0: zd1211b chip 2019:5303 v4810 high 00-90-cc AL2230_RF pa0 ---N- Nov 5 11:20:24 somesystem NetworkManager: <WARN> nm_device_hw_bring_up(): (wlan0): device not up after timeout! Nov 5 11:20:24 somesystem NetworkManager: <info> (wlan0): deactivating device (reason: 2). Nov 5 11:20:24 somesystem kernel: [ 196.463814] usb 2-1: firmware: requesting zd1211/zd1211b_ub Nov 5 11:20:24 somesystem kernel: [ 196.466823] usb 2-1: firmware: requesting zd1211/zd1211b_uphr Nov 5 11:20:29 somesystem wpa_supplicant[978]: Could not set interface 'wlan0' UP Nov 5 11:20:29 somesystem wpa_supplicant[978]: Failed to initialize driver interface Nov 5 11:20:29 somesystem NetworkManager: <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. Gnome tells me in the network menu that the device was "not ready". It appears in iwconfig but not in ifconfig. The same symptoms appear when I boot from the live CD. How can I solve this dilemma?

  Read the article

• Need to know who is hogging my bandwidth?

  - by Dev

  I have an ethernet connection to my iMac and with Internet sharing I am broadcasting the wireless network from my mac rather than using a wireless router. I use it to connect other devices wirelessly to the internet. But this makes all the traffic flow through my iMac. I wanted a way to analyze the traffic so that I know what connected devices are hogging the bandwidth at a given time and from which websites? I installed wireshark for mac and played around a little but it seems like an overkill when you first look at it. Can someone please help with few instructions to get what I need or any other way other than using wireshark? Thanks Dev.

  Read the article

• Configuring 2 XBee Modules on OSX for wireless connection

  - by Annette

  I am trying find out how and with which program for OSX (10.5.8) I can configure serial ports? I am trying to establish a wireless connection between two Xbee´s (RF modules) and cannot figure out how to use ZTerm nor screen under Terminal. The setup I am using is: an Arduino+Xbeeshield+Xbee with external power supply, and an xbee on the xbee explorer connected to the Computer via USB. I am trying to gather information on this through various forums, but most of them cover the configuration issue for PC using X-CTU (which I tried with CrossOver but it doesn´t recognize ny of my ports). According to one source, using screen under Terminal should show me all my serial ports, particularly /dev/tty.KeySerial1 - but it doesn´t show, even though I´ve plugged in both my arduino+xbee shield and the xbee on the explorer.

  Read the article

• Mac OS X 10.6 assign mapped IP to Windows 7 VM in Parallels

  - by Alex

  I'm trying to assign a mapped IP address to a Windows 7 VM. I have setup running in Parallels 5 in wireless bridged networking mode. The problem I am having is that it looks like the VM is actually broadcasting the MAC address of the host machine and thus causing a clash of IP addresses on the network. This is my current setup: Macbook Pro :~ ifconfig -a lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:b0:df:31:b4 media: autoselect status: inactive supported media: none autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,flow-control> 10baseT/UTP <full-duplex,hw-loopback> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,flow-control> 100baseTX <full-duplex,hw-loopback> 1000baseT <full-duplex> 1000baseT <full-duplex,flow-control> 1000baseT <full-duplex,hw-loopback> fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078 lladdr 00:26:b0:ff:fe:df:31:b4 media: autoselect <full-duplex> status: inactive supported media: autoselect <full-duplex> en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::226:bbff:fe0a:59a1%en1 prefixlen 64 scopeid 0x6 inet 192.168.1.97 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:26:bb:0a:59:a1 media: autoselect status: active supported media: autoselect vnic0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.1.81 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:1c:42:00:00:08 media: autoselect status: active supported media: autoselect vnic1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255 ether 00:1c:42:00:00:09 media: autoselect status: active supported media: autoselect Windows 7: :~ ipconfig -all Windows IP Configuration Host Name . . . . . . . . . . . . : Alex-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Parallels Ethernet Adapter Physical Address. . . . . . . . . : 00-1C-42-B8-E7-B4 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Teredo Tunneling Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{ACAC7EBB-5E5F-4F53-AFD9-E6EAEEA0FEE2}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Billion Bipac 7200 modem router: In DHCP server settings have the following two mapping entries. alex-macbook-win7 00:1c:42:00:00:08 192.168.1.98 alex-macbook 00:26:bb:0a:59:a1 192.168.1.97 The problem I have is that when the VM starts up it gets assigned the 192.168.1.97 address instead of the .98 address and thus networking on the host stops working as it says there is a clash. I have tried removing the mapping for "alex-macbook" which results in the guest machine being assigned a normal DHCP address and NOT the one that is in the mapping of the router.

  Read the article

• WiFi & GbE Slow while Both Active.

  - by Mark Tomlin

  I'm having a problem with my WiFi network connection when I use my wired GbE connection concurrently on my Laptop. I'm using my WiFi for Internet access, and general web surfing and I'm using my GbE connection to connect to my PlayStation so I can stream media. The WiFi connection is via a Linksys 610N connected to my Cable Modem. Where as the GbE connection is a direct connection from my Ethernet port to the Ethernet port of the PS3 via a Cat-5 cable (no router in between this connection). As soon as I connect the cable from the PS3 to my Ethernet port on my Laptop the WiFi connection slows to a halt, but then allows for a connection to the web as normal but at much slower speeds for the things like BitTorrent that stops completely. It seems to me that Windows can't handle both connections at once. It will have both active but it can only accept and send packets on one device at one time. I can get WiFi connections to work to go to websites and the like, but once I use my GbE connection to share media between my Laptop and my PS3 the Wifi connection dies out and I no longer have access to the internet. I setup my connection on the PS3 and the Laptop following the insturctions posted here: http://forums.finalgear.com/problems/s14e01-ps3-size-problem-40642/#post1188132 And the following is the results of my ipconfig. Windows IP Configuration Host Name . . . . . . . . . . . . : dygear Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter WiFi: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-19-**-**-**-** Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.111 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 167.206.254.2 167.206.254.1 Lease Obtained. . . . . . . . . . : Wednesday, May 19, 2010 08:55:30 Lease Expires . . . . . . . . . . : Thursday, May 20, 2010 08:55:30 Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-16-**-**-**-** Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Any ideas?

  Read the article

• What are these errors when I try to "make" the driver of my wireless adapter?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• What are these errors when I try to "make" the driver of my wireless network?

  - by Tom Brito

  I got got a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme file say to use the "make" command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g

  Read the article

• Is it possible to use multi keyboards with multi keyboard layouts simultaneously?

  - by mono

  Considering to switch to dvorak layout, but this terminal is used by multi users as the same user account. It is unacceptable to ask all people to switch layout, plus it is hard to use dvorak layout with a keyboard qwerty-ly labeled. But there are spare (USB,qwerty) keyboards, so if I plug another keyboard in and be able to use multi layouts on different psyical keyboard simultaneously (I will rearrange letters on keys), the problem get solved. solution for either windows or linux is fine. anyway thanks all.

  Read the article

• Is it possible to use different keyboards for different applications?

  - by Paperflyer

  What I would like is this: I would have two keyboards. One of them is "connected" to Matlab, the other is "connected" to my text editor of choice. This way, I could edit some script and still test some commands in Matlab without having to constantly switch between the applications. Basically, I would want to have an additional keyboard attached to my computer that solely controlled Matlab. That would be awesome! Is there any way to do this? Preferably with OSX, but it would be fun on Windows or Linux, too.

  Read the article

• [Wireless LAN]hostapd is giving error whwn running in target board

  - by Renjith G

  hi, I got the following error when i tried to run the hostapd command in my target board. Any idea about this? /etc # hostapd -dd hostapd.conf Configuration file: hostapd.conf madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid '"RG_WLAN Testing Renjith G"' SSID - hexdump_ascii(len=27): 22 52 47 5f 57 4c 41 4e 20 54 65 73 74 69 6e 67 "RG_WLAN Testing 20 52 65 6e 6a 69 74 68 20 47 22 Renjith G" PSK (ASCII passphrase) - hexdump_ascii(len=12): 6d 79 70 61 73 73 70 68 72 61 73 65 mypassphrase PSK (from passphrase) - hexdump(len=32): 70 6f a6 92 da 9c a8 3b ff 36 85 76 f3 11 9c 5e 5d 4a 4b 79 f4 4e 18 f6 b1 b8 09 af 6c 9c 6c 21 madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x2 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA=0x1 WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 madwifi_set_iface_flags: dev_up=1 ath0: Setup of interface done. l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8b1a len=40 Register Fail Register Fail WPA: group state machine entering state SETKEYS (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] wpa_group_setkeys: GKeyDoneStations=0 WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=2 Signal 2 received - terminating Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_set_ieee8021x: enabled=0 madwifi_set_iface_flags: dev_up=0

  Read the article

• DD-WRT Linksys WRT320N Max Tx Power

  - by Peter Stegnar

  What is the save max Tx Power setting for WRT320N?

  Read the article

• Tunnel into Sonicwall VPN while on Sonicwall wifi?

  - by Patrick Harrington

  Hey all, I am able to hit my company's VPN while I am at home using a dedicated IP with no issue. When I am at work, the VPN we use (a Sonicwall router/VPN/wifi access point), I can get outside internet fine, but am unable to connect to the VPN. I know that the wifi puts me on a different subnet, and when I try to connect to the normal VPN IP it won't work, and a traceroute just times out. Any suggestions? Might there be an internal IP I need to hit while here at work?

  Read the article

• win xp wifi networking

  - by user3485532

  I have 2 pcs with win xp and a wifi router ( without outgoing internet connection )...my job was to connect them over wifi to share some files. router was properly configured, both computers connected to wifi without problems, but when I tried to network them I could not see them in workgroup...i changed their names and added them to same workgroup but i couldn't connect pc1 to pc2 ( i could ping router from each pc but pinging other computer resulted in ping timeout) ..now i cant figure out why this is not working since I've done this before on more complex networks and it should work but...( maybe I have gremlins hiding somewhere..) edit1: Firewall is down on both machines( I disengaged it in both control panel and in services) and folder sharing and permissions are ok.. edit2: I know about Ad Hoc network ( wlan-to-wlan, without router/switch ) but that's not what I am trying to accomplish here :)

  Read the article

• Wifi not working after a few minutes

  - by drtanz

  I'm using a few MacBooks and iPads connected to a router via WiFi. The problem is that a few minutes after they connect via WiFi the connection stops working. This happens on all devices. I went into the router settings by connecting via cable and everything seems in order. Connecting a laptop via cable to the router I can use internet as normal, the problem is only with WiFi. What can be the problem here? Here are the connected clients Connected Clients MAC Address Idle(s) RSSI(dBm) IP Addr Host Name Mode Speed (kbps) 14:10:9F:F3:48:D6 1 -36 192.168.0.5 Jeans-Air n 78000 14:99:E2:C6:41:10 1 -36 192.168.0.8 JeanGaleasiPad n 24000 Here's the router event log Mon Dec 30 04:12:30 2013 Notice (6) WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:N/A)... Mon Dec 30 04:12:25 2013 Notice (6) WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:5) -... Mon Dec 30 02:17:56 2013 Notice (6) WiFi Interface [wl0] set to Channel 40 (Side-Band Channel:36)... Mon Dec 30 02:16:04 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:7) ... Mon Dec 30 01:59:26 2013 Notice (6) WiFi Interface [wl0] set to Channel 6 (Side-Band Channel:N/A)... Mon Dec 30 01:59:22 2013 Notice (6) WiFi Interface [wl0] set to Channel 6 (Side-Band Channel:2) -... Sun Dec 29 23:27:51 2013 Notice (6) WiFi Interface [wl0] set to Channel 1 (Side-Band Channel:N/A)... Sun Dec 29 23:27:49 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:N/A... Sun Dec 29 14:32:55 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Sat Dec 28 13:08:19 2013 Error (4) DHCP REBIND WARNING - Field invalid in response ;CM-MAC=1c:3e... Fri Dec 27 18:10:19 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Fri Dec 27 16:08:55 2013 Error (4) Map Request Retry Timeout;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Thu Dec 26 21:08:53 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:7) ... Thu Dec 26 20:43:50 2013 Notice (6) WiFi Interface [wl0] set to Channel 11 (Side-Band Channel:N/A... Tue Dec 24 12:45:03 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Tue Dec 24 04:55:52 2013 Error (4) Map Request Retry Timeout;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Mon Dec 23 12:32:00 2013 Notice (6) TLV-11 - unrecognized OID;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Mon Dec 23 12:32:00 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.9;CM-MAC=1c:3e:... Mon Dec 23 12:32:00 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.8;CM-MAC=1c:3e:... Mon Dec 23 12:32:00 2013 Warning (5) DHCP WARNING - Non-critical field invalid in response ;CM-MAC... Mon Dec 23 18:32:02 2013 Notice (6) Honoring MDD; IP provisioning mode = IPv4 Mon Dec 23 18:31:10 2013 Critical (3) No Ranging Response received - T3 time-out;CM-MAC=1c:3e:84:f1... Mon Dec 23 18:28:57 2013 Critical (3) Received Response to Broadcast Maintenance Request, But no Un... Mon Dec 23 18:28:25 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ... Mon Dec 23 12:17:48 2013 Notice (6) TLV-11 - unrecognized OID;CM-MAC=1c:3e:84:f1:6b:84;CMTS-MAC=0... Mon Dec 23 12:17:48 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.9;CM-MAC=1c:3e:... Mon Dec 23 12:17:48 2013 Error (4) Missing BP Configuration Setting TLV Type: 17.8;CM-MAC=1c:3e:... Mon Dec 23 12:17:48 2013 Warning (5) DHCP WARNING - Non-critical field invalid in response ;CM-MAC... Mon Dec 23 18:17:48 2013 Notice (6) Honoring MDD; IP provisioning mode = IPv4 Mon Dec 23 18:16:58 2013 Critical (3) No Ranging Response received - T3 time-out;CM-MAC=1c:3e:84:f1... Mon Dec 23 18:16:15 2013 Critical (3) Received Response to Broadcast Maintenance Request, But no Un... Mon Dec 23 18:15:43 2013 Critical (3) Started Unicast Maintenance Ranging - No Response received - ...

  Read the article

• What is the difference between SoftAP and Wifi-Direct?

  - by user1129812

  I want to buy a Wifi Dongle that, besides acting as an ordinary Wifi client, could change its mode to work as an Access Point too. Should I buy a dongle with SoftAP or should I buy one with Wifi-Direct ? What is the difference between these 2 concepts ? Or is there any difference between them ? Moreover, what chipset (Realtek, Ralink etc) could provide such a functionality ? Which chipset that has this functionality could work happily in a Debian/Ubuntu 32 bit environment ? Thanks in advance for any suggestion.

  Read the article

< Previous Page | 78 79 80 81 82 83 84 85 86 87 88 89  | Next Page >