Search Results

Search found 2301 results on 93 pages for 'calico cat'.

Page 83/93 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

  • Can only bring up one of two interfaces

    - by mstaessen
    I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

    Read the article

  • SIGINT and SIGTSTP ignored by most common applications

    - by Vašek Potocek
    After the last upgrade to my Fedora, a strange behaviour started occurring in X terminal applications. I can't seem to stop any process using Ctrl+C, it just results in printing ^C to the console. Similarly, Ctrl+Z prints ^Z and the process goes on. Both work well in non-graphical virtual consoles. I checked stty -a and it seems perfectly normal: speed 38400 baud; rows 24; columns 80; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = M-^?; eol2 = M-^?; swtch = M-^?; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; -parenb -parodd cs8 hupcl -cstopb cread -clocal -crtscts -ignbrk brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc ixany imaxbel iutf8 opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke This is independent of the terminal (gnome-terminal, XFCE4 terminal, xterm). I later noticed that it may not be caused by the terminal at all: INT or TSTP sent directly to the respective process are ignored, too. This comprises various applications I used to terminate using Ctrl+C on a regular basis (and which often don't have any better means of exiting): cat, find, tail -f, java, ping, mplayer when stuck on a broken file... Even bash ignores Ctrl+C when I want to break a command line I have been entering and then changed my mind (no ^C is printed in this case). I need to delete it character by character (of which there may be hundreds if filename completion has been used) or intentionally run the unwanted command. Strangely enough, vim does recognize Ctrl+C—just to say its "use :quit", of course. This is extremely annoying and prevents me from working efficiently. Everything had been working until lately, maybe a week ago or so. I can not find any possible causes in Google, perhaps I'm trying wrong search terms or misidentifying the main problem. What could be it and how could I revert the standard behaviour, please? Update Ctrl+Z works sometimes. It seems that in the very first terminal I launch after logging in it stops the running command but stops working after that.

    Read the article

  • Can not get sound over hdmi in kubuntu 9.10

    - by user32509
    I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

    Read the article

  • Can't ping Ip over bridge

    - by tmn29a
    I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

    Read the article

  • Hyper-V Ubuntu Networking Problems Copying Large Amounts of Data

    - by Anonymous
    I am trying to copy a large amount (about 50 GB) of data over my network from a Hyper-V-hosted virtual machine running Ubuntu 11.04 (Natty Narwhal) to another (non-virtual) Ubuntu host that I plan to use for testing upgrades to one of our web applications. The problem I am having is with the virtual machine, which I shall refer to in what follows as "source.host". This machine is running 64-bit Ubuntu Server with the 2.6.38-8-server kernel and the Microsoft Linux Integration Components for Hyper-V kernel modules (hv_utils, hv_timesource, hv_netvsc, hv_blkvsc, hv_storvsc, and hv_vmbus) loaded. It uses a Hyper-V "synthetic network adapter" for its networking interface. To do the copy, I log on to the machine with the data and run the following commands (Call the remote machine "destination.host".): $ cd /path/to/data $ tar -cvf - datafolder/ | ssh [email protected] "cat > ~/data.tar" This runs for a while and then suddenly stops after transferring somewhere from 2-6 GB. The terminal on the source.host machine displays a Write failed: broken pipe error. The odd part is this: after this occurs, the "source.host" machine is no longer able to talk to the rest of the network. I cannot ping any other hosts on the network from the "source.host" machine, and I cannot ping the "source.host" machine from any other host on the network. I am equally unable to access the any of the web services hosted on "source.host". Running ifconfig on "source.host" shows the network adapter to be up and running as usual with the correct IP address and everything. I tried restarting the networking service with $ /etc/init.d/networking restart but the problem does not go away. Restarting the machine makes it capable of talking to the network again -- it can ping and be pinged by other hosts, and the web services are also accessible and usable as normal -- but attempting the copy operation again results in the same failure, requiring another restart. As an experiment, I tried replacing the tar -- ssh pipeline above with a straight scp: $ scp -r datafolder/ [email protected]:~ but to no avail Thinking that the issue might have to do with the kernel packet-send buffers filling up, I tried increasing the buffer size to 12 MB (up from the 128 KB default) with # echo 12582911 > /proc/sys/net/core/wmem_max but this also had no effect. I'm guessing at this point that it might be a problem with the Microsoft synthetic network driver, but I don't really know. Does anyone have any suggestions? Thank you very much in advance!

    Read the article

  • Galaxy Tab 3 producing continuous LightSensor error in LogCat

    - by Richard Tingle
    I am using a Galaxy Tab 3 as a test device for writing an android app. As such I'm interested in the output of the LogCat which is being filled with these error level messages. The device itself appears to work correctly, apps which rely on the light sensor correctly respond to it and the number in the error itself goes down if the light sensor is obscured. If I wasn't using it to develop apps I wouldn't even be aware of the issue but I believe it is an issue with the device itself not my app: simply plugging the tab 3 into the computer and using Eclipse - ADT to look at the LogCat without any app running leads to these errors being shown. I know I could filter the LogCat to ignore these errors but inconvenience aside; they concern me. A sample of the log cat is below (it generates errors continuously). This is on verbose so it includes some debug level (D/) messages as well as the error level messages (E/). How can I correct the device to no longer generate these errors. 06-11 10:08:45.789: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:45.992: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.195: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.398: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.601: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:46.804: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.007: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.210: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.414: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.617: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:47.820: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:48.023: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:48.039: D/dalvikvm(15201): GC_CONCURRENT freed 1947K, 17% free 16973K/20359K, paused 13ms+13ms, total 50ms 06-11 10:08:48.226: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:48.429: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13 06-11 10:08:48.632: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13 06-11 10:08:48.632: D/STATUSBAR-NetworkController(472): refreshSignalCluster: data=0 bt=false 06-11 10:08:48.835: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.039: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.242: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.445: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13 06-11 10:08:49.632: D/STATUSBAR-NetworkController(472): refreshSignalCluster: data=0 bt=false 06-11 10:08:49.648: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 14 06-11 10:08:49.851: E/LightSensor(377): LightSensor::readEvents mPendingEvent.light = 13

    Read the article

  • [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

    - by Beco
    I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

    Read the article

  • Xml failing to deserialise

    - by Carnotaurus
    I call a method to get my pages [see GetPages(String xmlFullFilePath)]. The FromXElement method is supposed to deserialise the LitePropertyData elements to strongly type LitePropertyData objects. Instead it fails on the following line: return (T)xmlSerializer.Deserialize(memoryStream); and gives the following error: <LitePropertyData xmlns=''> was not expected. What am I doing wrong? I have included the methods that I call and the xml data: public static T FromXElement<T>(this XElement xElement) { using (var memoryStream = new MemoryStream(Encoding.ASCII.GetBytes(xElement.ToString()))) { var xmlSerializer = new XmlSerializer(typeof(T)); return (T)xmlSerializer.Deserialize(memoryStream); } } public static List<LitePageData> GetPages(String xmlFullFilePath) { XDocument document = XDocument.Load(xmlFullFilePath); List<LitePageData> results = (from record in document.Descendants("row") select new LitePageData { Guid = IsValid(record, "Guid") ? record.Element("Guid").Value : null, ParentID = IsValid(record, "ParentID") ? Convert.ToInt32(record.Element("ParentID").Value) : (Int32?)null, Created = Convert.ToDateTime(record.Element("Created").Value), Changed = Convert.ToDateTime(record.Element("Changed").Value), Name = record.Element("Name").Value, ID = Convert.ToInt32(record.Element("ID").Value), LitePageTypeID = IsValid(record, "ParentID") ? Convert.ToInt32(record.Element("ParentID").Value) : (Int32?)null, Html = record.Element("Html").Value, FriendlyName = record.Element("FriendlyName").Value, Properties = record.Element("Properties") != null ? record.Element("Properties").Element("LitePropertyData").FromXElement<List<LitePropertyData>>() : new List<LitePropertyData>() }).ToList(); return results; } Here is the xml: <?xml version="1.0" encoding="utf-8"?> <root> <rows> <row> <ID>1</ID> <ImageUrl></ImageUrl> <Html>Home page</Html> <Created>01-01-2012</Created> <Changed>01-01-2012</Changed> <Name>Home page</Name> <FriendlyName>home-page</FriendlyName> </row> <row xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"> <Guid>edeaf468-f490-4271-bf4d-be145bc6a1fd</Guid> <ID>8</ID> <Name>Unused</Name> <ParentID>1</ParentID> <Created>2006-03-25T10:57:17</Created> <Changed>2012-07-17T12:24:30.0984747+01:00</Changed> <ChangedBy /> <LitePageTypeID xsi:nil="true" /> <Html> What is the purpose of this option? This option checks the current document for accessibility issues. It uses Bobby to provide details of whether the current web page conforms to W3C's WCAG criteria for web content accessibility. Issues with Bobby and Cynthia Bobby and Cynthia are free services that supposedly allow a user to expose web page accessibility barriers. It is something of a guide but perhaps a blunt instrument. I tested a few of the webpages that I have designed. Sure enough, my pages fall short and for good reason. I am not about to claim that Bobby and Cynthia are useless. Although it is useful and commendable tool, it project appears to be overly ambitious. Nevertheless, let me explain my issues with Bobby and Cynthia: First, certain W3C standards for designing web documents are often too strict and unworkable. For instance, in some versions W3C standards for HTML, certain tags should not include a particular attribute, whereas in others they are requisite if the document is to be ???well-formed???. The standard that a designer chooses is determined usually by the requirements specification document. This specifies which browsers and versions of those browsers that the web page is expected to correctly display. Forcing a hypertext document to conform strictly to a specific W3C standard for HTML is often no simple task. In the worst case, it cannot conform without losing some aesthetics or accessibility functionality. Second, the case of HTML documents is not an isolated case. Standards for XML, XSL, JavaScript, VBScript, are analogous. Therefore, you might imagine the problems when you begin to combine these languages and formats in an HTML document. Third, there is always more than one way to skin a cat. For example, Bobby and Cynthia may flag those IMG tags that do not contain a TITLE attribute. There might be good reason that a web developer chooses not to include the title attribute. The title attribute has a limited numbers of characters and does not support carriage returns. This is a major defect in the design of this tag. In fact, before the TITLE attribute was supported, there was the ALT attribute. Most browsers support both, yet they both perform a similar function. However, both attributes share the same deficiencies. In practice, there are instances where neither attribute would be used. Instead, for example, the developer would write some JavaScript or VBScript to circumvent these deficiencies. The concern is that Bobby and Cynthia would not notice this because it does not ???understand??? what the JavaScript does. </Html> <FriendlyName>unused</FriendlyName> <IsDeleted>false</IsDeleted> <Properties> <LitePropertyData> <Description>Image for the page</Description> <DisplayEditUI>true</DisplayEditUI> <OwnerTab>1</OwnerTab> <DisplayName>Image Url</DisplayName> <FieldOrder>1</FieldOrder> <IsRequired>false</IsRequired> <Name>ImageUrl</Name> <IsModified>false</IsModified> <ParentPageID>3</ParentPageID> <Type>String</Type> <Value xsi:type="xsd:string">smarter.jpg</Value> </LitePropertyData> <LitePropertyData> <Description>WebItemApplicationEnum</Description> <DisplayEditUI>true</DisplayEditUI> <OwnerTab>1</OwnerTab> <DisplayName>WebItemApplicationEnum</DisplayName> <FieldOrder>1</FieldOrder> <IsRequired>false</IsRequired> <Name>WebItemApplicationEnum</Name> <IsModified>false</IsModified> <ParentPageID>3</ParentPageID> <Type>Number</Type> <Value xsi:type="xsd:string">1</Value> </LitePropertyData> </Properties> <Seo> <Author>Phil Carney</Author> <Classification /> <Copyright>Carnotaurus</Copyright> <Description> What is the purpose of this option? This option checks the current document for accessibility issues. It uses Bobby to provide details of whether the current web page conforms to W3C's WCAG criteria for web content accessibility. Issues with Bobby and Cynthia Bobby and Cynthia are free services that supposedly allow a user to expose web page accessibility barriers. It is something of a guide but perhaps a blunt instrument. I tested a few of the webpages that I have designed. Sure enough, my pages fall short and for good reason. I am not about to claim that Bobby and Cynthia are useless. Although it is useful and commendable tool, it project appears to be overly ambitious. Nevertheless, let me explain my issues with Bobby and Cynthia: First, certain W3C standards for designing web documents are often too strict and unworkable. For instance, in some versions W3C standards for HTML, certain tags should not include a particular attribute, whereas in others they are requisite if the document is to be ???well-formed???. The standard that a designer chooses is determined usually by the requirements specification document. This specifies which browsers and versions of those browsers that the web page is expected to correctly display. Forcing a hypertext document to conform strictly to a specific W3C standard for HTML is often no simple task. In the worst case, it cannot conform without losing some aesthetics or accessibility functionality. Second, the case of HTML documents is not an isolated case. Standards for XML, XSL, JavaScript, VBScript, are analogous. Therefore, you might imagine the problems when you begin to combine these languages and formats in an HTML document. Third, there is always more than one way to skin a cat. For example, Bobby and Cynthia may flag those IMG tags that do not contain a TITLE attribute. There might be good reason that a web developer chooses not to include the title attribute. The title attribute has a limited numbers of characters and does not support carriage returns. This is a major defect in the design of this tag. In fact, before the TITLE attribute was supported, there was the ALT attribute. Most browsers support both, yet they both perform a similar function. However, both attributes share the same deficiencies. In practice, there are instances where neither attribute would be used. Instead, for example, the developer would write some JavaScript or VBScript to circumvent these deficiencies. The concern is that Bobby and Cynthia would not notice this because it does not ???understand??? what the JavaScript does. </Description> <Keywords>unused</Keywords> <Title>unused</Title> </Seo> </row> </rows> </root> EDIT Here are my entities: public class LitePropertyData { public virtual string Description { get; set; } public virtual bool DisplayEditUI { get; set; } public int OwnerTab { get; set; } public virtual string DisplayName { get; set; } public int FieldOrder { get; set; } public bool IsRequired { get; set; } public string Name { get; set; } public virtual bool IsModified { get; set; } public virtual int ParentPageID { get; set; } public LiteDataType Type { get; set; } public object Value { get; set; } } [Serializable] public class LitePageData { public String Guid { get; set; } public Int32 ID { get; set; } public String Name { get; set; } public Int32? ParentID { get; set; } public DateTime Created { get; set; } public String CreatedBy { get; set; } public DateTime Changed { get; set; } public String ChangedBy { get; set; } public Int32? LitePageTypeID { get; set; } public String Html { get; set; } public String FriendlyName { get; set; } public Boolean IsDeleted { get; set; } public List<LitePropertyData> Properties { get; set; } public LiteSeoPageData Seo { get; set; } /// <summary> /// Saves the specified XML full file path. /// </summary> /// <param name="xmlFullFilePath">The XML full file path.</param> public void Save(String xmlFullFilePath) { XDocument doc = XDocument.Load(xmlFullFilePath); XElement demoNode = this.ToXElement<LitePageData>(); demoNode.Name = "row"; doc.Descendants("rows").Single().Add(demoNode); doc.Save(xmlFullFilePath); } }

    Read the article

  • Issue with my wordpress functions.php script

    - by iMayne
    Hello peeps. Im having an issues when activating my theme in wordpress. I got this error message: "Parse error: syntax error, unexpected $end in C:\xampp\htdocs\xampp\wordpress\wp-content\themes\xit\functions.php on line 223". Whats wrong, I totally dont understand. The script of the php is: <?php if ( function_exists('register_sidebar') ) register_sidebar(array( 'before_widget' => '', 'after_widget' => '', 'before_title' => '<h2>', 'after_title' => '</h2>', )); function content($num) { $theContent = get_the_content(); $output = preg_replace('/<img[^>]+./','', $theContent); $limit = $num+1; $content = explode(' ', $output, $limit); array_pop($content); $content = implode(" ",$content)."..."; echo $content; } function post_is_in_descendant_category( $cats, $_post = null ) { foreach ( (array) $cats as $cat ) { // get_term_children() accepts integer ID only $descendants = get_term_children( (int) $cat, 'category'); if ( $descendants && in_category( $descendants, $_post ) ) return true; } return false; } //custom comments function mytheme_comment($comment, $args, $depth) { $GLOBALS['comment'] = $comment; ?> <li <?php comment_class(); ?> id="li-comment-<?php comment_ID() ?>"> <div id="comment-<?php comment_ID(); ?>"> <div class="comment-author vcard"> <div class="comment-meta commentmetadata"> <?php echo get_avatar($comment,$size='32',$default='http://www.gravatar.com/avatar/61a58ec1c1fba116f8424035089b7c71?s=32&d=&r=G' ); ?> <?php printf(__('%1$s at %2$s'), get_comment_date(), get_comment_time()) ?> <br /><?php printf(__('<strong>%s</strong> says:'), get_comment_author_link()) ?><?php edit_comment_link(__('(Edit)'),' ','') ?></div> </div> <?php if ($comment->comment_approved == '0') : ?> <em><?php _e('Your comment is awaiting moderation.') ?></em> <br /> <?php endif; ?> <div class="text"><?php comment_text() ?></div> <div class="reply"> <?php comment_reply_link(array_merge( $args, array('depth' => $depth, 'max_depth' => $args['max_depth']))) ?> </div> </div> <?php } add_action('admin_menu', 'xit_theme_page'); function xit_theme_page () { if ( count($_POST) > 0 && isset($_POST['xit_settings']) ) { $options = array ( 'style','logo_img','logo_alt','logo_txt', 'logo_tagline', 'tagline_width', 'contact_email','ads', 'advertise_page', 'twitter_link', 'facebook_link', 'flickr', 'about_tit', 'about_txt', 'analytics'); foreach ( $options as $opt ) { delete_option ( 'xit_'.$opt, $_POST[$opt] ); add_option ( 'xit_'.$opt, $_POST[$opt] ); } } add_theme_page(__('Xit Options'), __('Xit Options'), 'edit_themes', basename(__FILE__), 'xit_settings'); } function xit_settings () {?> <div class="wrap"> <h2>XIT Options Panel</h2> <form method="post" action=""> <table class="form-table"> <!-- General settings --> <tr> <th colspan="2"><strong>General Settings</strong></th> </tr> <tr valign="top"> <th scope="row"><label for="style">Theme Color Scheme</label></th> <td> <select name="style" id="style"> <option value="pink.css" <?php if(get_option('xit_style') == 'pink.css'){?>selected="selected"<?php }?>>pink.css</option> <option value="blue.css" <?php if(get_option('xit_style') == 'blue.css'){?>selected="selected"<?php }?>>blue.css</option> <option value="orange.css" <?php if(get_option('xit_style') == 'orange.css'){?>selected="selected"<?php }?>>orange.css</option> </select> </td> </tr> <tr valign="top"> <th scope="row"><label for="logo_img">Logo image (full path to image)</label></th> <td> <input name="logo_img" type="text" id="logo_img" value="<?php echo get_option('xit_logo_img'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="logo_alt">Logo image ALT text</label></th> <td> <input name="logo_alt" type="text" id="logo_alt" value="<?php echo get_option('xit_logo_alt'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="logo_txt">Text logo</label></th> <td> <input name="logo_txt" type="text" id="logo_txt" value="<?php echo get_option('xit_logo_txt'); ?>" class="regular-text" /> <br /><em>Leave this empty if you entered an image as logo</em> </td> </tr> <tr valign="top"> <th scope="row"><label for="logo_tagline">Logo Tag Line</label></th> <td> <input name="logo_tagline" type="text" id="logo_tagline" value="<?php echo get_option('xit_logo_tagline'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="tagline_width">Tag Line Box Width (px)</label><br /><em style="font-size:11px">Default width: 300px</em></th> <td> <input name="tagline_width" type="text" id="tagline_width" value="<?php echo get_option('xit_tagline_width'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="contact_email">Email Address for Contact Form</label></th> <td> <input name="contact_email" type="text" id="contact_email" value="<?php echo get_option('xit_contact_email'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="twitter_link">Twitter link</label></th> <td> <input name="twitter_link" type="text" id="twitter_link" value="<?php echo get_option('xit_twitter_link'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="facebook_link">Facebook link</label></th> <td> <input name="facebook_link" type="text" id="facebook_link" value="<?php echo get_option('xit_facebook_link'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="flickr">Flickr Photostream</label></th> <td> <select name="flickr" id="flickr"> <option value="yes" <?php if(get_option('xit_flickr') == 'yes'){?>selected="selected"<?php }?>>Yes</option> <option value="no" <?php if(get_option('xit_flickr') == 'no'){?>selected="selected"<?php }?>>No</option> </select> <br /><em>Make sure you have FlickrRSS plugin activated if you choose to enable Flickr Photostream</em> </td> </tr> <!-- Sidebar ABout Box--> <tr> <th colspan="2"><strong>Sidebar About Box</strong></th> </tr> <tr valign="top"> <th scope="row"><label for="about_tit">Title</label></th> <td> <input name="about_tit" type="text" id="about_tit" value="<?php echo get_option('xit_about_tit'); ?>" class="regular-text" /> </td> </tr> <tr valign="top"> <th scope="row"><label for="about_txt">Text</label></th> <td> <textarea cols="60" rows="5" name="about_txt" type="text" id="about_txt" class="regular-text" /><?php echo get_option('xit_about_txt'); ?></textarea> </td> </tr> <!-- Ads Box Settings --> <tr> <th colspan="2"><strong>Ads Box Settings</strong></th> </tr> <tr> <th><label for="ads">Ads Section Enabled:</label></th> <td> <select name="ads" id="ads"> <option value="yes" <?php if(get_option('xit_ads') == 'yes'){?>selected="selected"<?php }?>>Yes</option> <option value="no" <?php if(get_option('xit_ads') == 'no'){?>selected="selected"<?php }?>>No</option> </select> <br /><em>Make sure you have AdMinister plugin activated and have the position "Sidebar" created within the plugin.</em> </td> </tr> <tr valign="top"> <th scope="row"><label for="advertise_page">Advertise Page</label></th> <td> <?php wp_dropdown_pages("name=advertise_page&show_option_none=".__('- Select -')."&selected=" .get_option('xit_advertise_page')); ?> </td> </tr> <!-- Google Analytics --> <tr> <th><label for="ads">Google Analytics code:</label></th> <td> <textarea name="analytics" id="analytics" rows="7" cols="70" style="font-size:11px;"><?php echo stripslashes(get_option('xit_analytics')); ?></textarea> </td> </tr> </table> <p class="submit"> <input type="submit" name="Submit" class="button-primary" value="Save Changes" /> <input type="hidden" name="xit_settings" value="save" style="display:none;" /> </p> </form> </div> <? }?> <?php function get_first_image() { global $post, $posts; $first_img = ''; ob_start(); ob_end_clean(); $output = preg_match_all('/<img.+src=[\'"]([^\'"]+)[\'"].*>/i', $post->post_content, $matches); $first_img = $matches [1] [0]; if(empty($first_img)){ //Defines a default image $first_img = "/images/default.jpg"; } return $first_img; } ?> The last line is line 223.

    Read the article

  • Syntax error, unexpected '}' wordpress error

    - by Zach Johnson
    Hello I am not a PHP programmer so I have no idea what the problem is here. Basiclly I am trying to use a wordpress theme but I get this error The Parse error: syntax error, unexpected '}' in / home/a5618915/public_html/photo/wp-content/themes/iphoto/functions.php on line 1 I have no Idea what exactly is wrong in the php file. The code for the functions.php is below. If someone could point out whats wrong I would be really grateful. <?php define('THEME_NAME','iphoto'); load_theme_textdomain( THEME_NAME,TEMPLATEPATH .'/languages'); add_custom_background(); add_theme_support( 'automatic-feed-links' ); add_theme_support( 'post-formats', array( 'video')); if ( function_exists('register_nav_menus') ) { register_nav_menus(array('primary' => 'header')); } add_action('wp_ajax_b_ajax_post_action', 'b_ajax_callback'); function b_ajax_callback() { global $wpdb; if(isset($_POST['type']) && $_POST['type'] == 'upload') { $clickedID = $_POST['data']; $filename = $_FILES[$clickedID]; $filename['name'] = preg_replace('/[^a-zA-Z0-9._-]/', '', $filename['name']); $override['test_form'] = false; $override['action'] = 'wp_handle_upload'; $uploaded_file = wp_handle_upload($filename,$override); $upload_tracking[] = $clickedID; update_option($clickedID, $uploaded_file['url'] ); if(!empty($uploaded_file['error'])) {echo 'Upload Error: ' . $uploaded_file['error']; } else { echo $uploaded_file['url']; } } die(); } function post_thumbnail($a){ global $post; $post_img = ''; ob_start(); ob_end_clean(); $output = preg_match_all('/\<img.+?src="(.+?)".*?\/>/is',$post->post_content,$matches ,PREG_SET_ORDER); $cnt = count( $matches ); if($a==1){ if($cnt>0){ if($cnt>1){ if($cnt>3) $cnt=3; for($i=0;$i<$cnt;$i++){ $post_current = $i+1; $post_img_src = $matches[$i][1]; if($i==0){$post_spans .= '<span class="current">'.$post_current.'</span>';}else{ $post_spans .= '<span>'.$post_current.'</span>'; } $post_imgs .='<img src="'.get_bloginfo('template_url').'/timthumb.php?src='.$post_img_src.'&amp;w=285&amp;zc=1" />'; } $post_img = $post_imgs.'<span class="imgNav">'.$post_spans.'</span>'; }else{ $post_img_src = $matches [0][1]; $post_img = '<img src="'.get_bloginfo('template_url').'/timthumb.php?src='.$post_img_src.'&amp;w=285&amp;zc=1" />'; } echo $post_img; } }else{ return $cnt; } } function post_content_thumbnail($c) { if(is_single()){ $c = preg_replace('/\width="*".+?height="*"/i', '', $c); $s = array('/src="(.+?.(jpg|bmp|png|jepg|gif))".+?/i' => 'src="'.get_bloginfo("template_url").'/timthumb.php?src=$1&amp;h=440&amp;zc=1"'); foreach($s as $p => $r){ $c = preg_replace($p,$r,$c); } return $c; } } add_filter( 'the_content', 'post_content_thumbnail' ); function ajax_post(){ if( isset($_GET['action'])&& $_GET['action'] == 'ajax_post'){ if(isset($_GET['cat'])){ $args = array( 'category_name' => $_GET['cat'], 'paged' => $_GET['pag'] ); }else if(isset($_GET['pag'])){ $args = array( 'paged' => $_GET['pag'] ); } query_posts($args); if(have_posts()){while (have_posts()):the_post();?> <?php get_template_part( 'content', get_post_format() ); ?> <?php endwhile;} die(); }else{return;} } add_action('init', 'ajax_post'); function pagenavi( $p = 2 ) { if ( is_singular() ) return; global $wp_query,$paged; $max_page = $wp_query->max_num_pages; if ( $max_page == 1 ){ echo '<span id="post-current">1</span> / <span id="post-count">1</span>'; return; } if ( empty( $paged ) ) $paged = 1; if ( $paged >1 ) echo "<a id='prev' title='Prev' href='",esc_html( get_pagenum_link( $paged -1 ) ),"'>&lt;&lt;</a> "; echo '<span id="post-current">'.$paged .'</span> / <span id="post-count">'.$max_page .'</span>'; if ( $paged <$max_page ) echo "<a id='next' title='Next' href='",esc_html( get_pagenum_link( $paged +1) ),"'>&gt;&gt;</a> "; } function iphoto_comment($comment,$args,$depth) { $GLOBALS['comment'] = $comment; ;echo ' <li ';comment_class();;echo ' id="li-comment-';comment_ID() ;echo '" > <div id="comment-';comment_ID();;echo '" class="comment-body"> <div class="commentmeta">';echo get_avatar( $comment->comment_author_email,$size = '48');;echo '</div> ';if ($comment->comment_approved == '0') : ;echo ' <em>';_e('Your comment is awaiting moderation.') ;echo '</em><br /> ';endif;;echo ' <div class="commentmetadata">&nbsp;-&nbsp;';printf(__('%1$s %2$s'),get_comment_date('Y.n.d'),get_comment_time('G:i'));;echo '</div> <div class="reply">';comment_reply_link(array_merge( $args,array('depth'=>$depth,'max_depth'=>$args['max_depth'],'reply_text'=>__('Reply')))) ;echo '</div> <div class="vcard">';printf(__('%s'),get_comment_author_link()) ;echo '</div> ';comment_text() ;echo ' </div> '; } add_action('admin_init', 'iphoto_init'); function iphoto_init() { if (isset($_GET['page']) && $_GET['page'] == 'functions.php') { $dir = get_bloginfo('template_directory'); wp_enqueue_script('adminjquery', $dir . '/includes/admin.js', false, '1.0.0', false); wp_enqueue_style('admincss', $dir . '/includes/admin.css', false, '1.0.0', 'screen'); } } add_action('admin_menu','iphoto_page'); function iphoto_page (){ if ( count($_POST) >0 &&isset($_POST['iphoto_settings']) ){ $options = array ('keywords','description','analytics','lib','views','noajax','animate','phzoom','copyright'); foreach ( $options as $opt ){ delete_option ( 'iphoto_'.$opt,$_POST[$opt] ); add_option ( 'iphoto_'.$opt,$_POST[$opt] ); } } add_theme_page('iPhoto '.__('Theme Options',THEME_NAME),__('Theme Options',THEME_NAME),'edit_themes',basename(__FILE__),'iphoto_settings'); } function iphoto_settings(){?> <div class="wrap"> <div> <h2><?php _e( 'iPhoto Theme Options<span>Version: ',THEME_NAME);?><?php $theme_data=get_theme_data(TEMPLATEPATH . '/style.css'); echo $theme_data['Version'];?></span></h2> </div> <div class="clear"></div> <form method="post" action=""> <div id="theme-Option"> <div id="theme-menu"> <span class="m1"><?php _e( 'jQuery Effect',THEME_NAME);?></span> <span class="m2"><?php _e( 'Relative Plugins',THEME_NAME);?></span> <span class="m3"><?php _e( 'Website Information',THEME_NAME);?></span> <span class="m4"><?php _e( 'Analytics Code',THEME_NAME);?></span> <span class="m5"><?php _e( 'Footer Copyright',THEME_NAME);?></span> <span class="m6"><?php _e( 'iPhoto Theme Declare',THEME_NAME);?></span> <div class="clear"></div> </div> <div id="theme-content"> <ul> <li> <tr><td> <em><?php _e( 'iPhoto use jquery 1.4.4 which contained in this theme, you can also use the Google one instead.',THEME_NAME);?></em><br/> <label><input name="lib" type="checkbox" id="lib" value="1" <?php if (get_option('iphoto_lib')!='') echo 'checked="checked"' ;?>/><?php _e( 'Load the jQuery Library supported by Google',THEME_NAME);?></label><br/><br/> </td></tr> <tr><td> <em><?php _e( 'Index page infinite loading posts.',THEME_NAME);?></em><br/> <label><input name="noajax" type="checkbox" id="noajax" value="1" <?php if (get_option('iphoto_noajax')!='') echo 'checked="checked"' ;?>/><?php _e( 'Deactivate the Infinite loading posts',THEME_NAME);?></label><br/><br/> </td></tr> <tr><td> <em><?php _e( '<strong>Animation of relayout elements</strong>',THEME_NAME);?></em><br /> <input name="animate" type="checkbox" id="animate" value="1" <?php if (get_option('iphoto_animate')!='') echo 'checked="checked"';?>/><?php _e( 'Deactivate animation effect on index page',THEME_NAME);?> </td></tr> </li> <li> <tr><td> <em><?php _e( 'WP-PostViews, Enables you to display how many times a post/page had been viewed.',THEME_NAME);?></em><br/> <label><input name="views" type="checkbox" id="views" value="1" <?php if (get_option('iphoto_views')!='') echo 'checked="checked"' ?>/><?php _e( 'Activate WP-PostViews',THEME_NAME);?></label><br/><br/> </td></tr> </li> <li> <tr><td> <?php _e( '<em>Keywords, separate by English commas. like MuFeng, Computer, Software</em>',THEME_NAME);?><br/> <textarea name="keywords" id="keywords" rows="1" cols="70" style="font-size:11px;width:100%;"><?php echo get_option('iphoto_keywords');?></textarea><br/> </td></tr> <tr><td> <?php _e( '<em>Description, explain what\'s this site about. like MuFeng, Breathing the wind</em>',THEME_NAME);?><br/> <textarea name="description" id="description" rows="3" cols="70" style="font-size:11px;width:100%;"><?php echo get_option('iphoto_description');?></textarea> </td></tr> </li> <li> <tr><td> <?php _e( 'You can get your Google Analytics code <a target="_blank" href="https://www.google.com/analytics/settings/check_status_profile_handler">here</a>.',THEME_NAME);?></label><br> <textarea name="analytics" id="analytics" rows="5" cols="70" style="font-size:11px;width:100%;"><?php echo stripslashes(get_option('iphoto_analytics'));?></textarea> </td></tr> </li> <li> <tr><td> <textarea name="copyright" id="copyright" rows="5" cols="70" style="font-size:11px;width:100%;"><?php if(stripslashes(get_option('iphoto_copyright'))!=''){echo stripslashes(get_option('iphoto_copyright'));}else{echo 'Copyright &copy; '.date('Y').' '.'<a href="'.home_url( '/').'" title="'.esc_attr( get_bloginfo( 'name') ).'">'.esc_attr( get_bloginfo( 'name') ).'</a> All rights reserved'; };?></textarea> <br/><em><?php _e( '<b>Preview</b>',THEME_NAME);?><span> : </span><span><?php if(stripslashes(get_option('iphoto_copyright'))!=''){echo stripslashes(get_option('iphoto_copyright'));}else{echo 'Copyright &copy; '.date('Y').' '.'<a href="'.home_url( '/').'" title="'.esc_attr( get_bloginfo( 'name') ).'">'.esc_attr( get_bloginfo( 'name') ).'</a> All rights reserved'; };?></span></em> </td></tr> </li> <li> <tr><td> <p><?php _e('iPhoto is created, developed and maintained by <a href="http://mufeng.me/">MuFeng</a>. If you like iPhoto, please donate. It will help in developing new features and versions.',THEME_NAME);?><?php _e('Alipay',THEME_NAME);?>:</strong> <a href="http://www.alipay.com" target="_blank" title="Alipay">[email protected]</a></p> <h3 style="color:#333" id="introduce"><?php _e( 'Introduction',THEME_NAME);?></h3> <p style="text-indent: 2em;margin:10px 0;"><?php _e( 'iPhoto is evolved from one theme of Tumblr and turned it into a photo theme which can be used at wordpress.',THEME_NAME);?></p> <h3 style="color:#333"><?php _e( 'Published Address',THEME_NAME);?></h3> <p id="release" style="text-indent: 2em;margin:10px 0;"><a href="http://mufeng.me/wordpress-theme-iphoto.html" target="_blank">http://mufeng.me/wordpress-theme-iphoto.html</a></p> <h3 style="color:#333"><?php _e( 'Preview Address',THEME_NAME);?></h3> <p id="preview" style="text-indent: 2em;margin:10px 0;"><a href="http://mufeng.me/photo/" target="_blank">http://mufeng.me/photo/</a></p> <h3 style="color:#333" id="bug"><?php _e( 'Report Bugs',THEME_NAME);?></h3> <p style="text-indent: 2em;margin:10px 0;"><?php _e( 'Weibo <a href="http://weibo.com/meapo" target="_blank">@mufeng.me</a> or leave a message at <a href="http://mufeng.me" target="_blank">http://mufeng.me</a>?',THEME_NAME);?></p> </td></tr> </li> </ul> </div> </div> <p class="submit"> <input type="submit" name="Submit" class="button-primary" value="<?php _e( 'Save Options',THEME_NAME);?>" /> <input type="hidden" name="iphoto_settings" value="save" style="display:none;" /> </p> </form> </div> <?php } ?>

    Read the article

  • nm-applet gone?

    - by welp
    nm-applet seems to have disappeared from my system. I am running 12.10. Here's what I get when I check my package manager logs: ? ~ grep network-manager /var/log/dpkg.log 2012-10-06 10:37:08 upgrade network-manager-gnome:amd64 0.9.6.2-0ubuntu5 0.9.6.2-0ubuntu6 2012-10-06 10:37:08 status half-configured network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:08 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:09 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu5 2012-10-06 10:37:09 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-06 10:37:09 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-06 10:39:50 configure network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-06 10:39:50 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-06 10:39:50 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-06 10:39:50 status half-configured network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-06 10:39:50 status installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 remove network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-configured network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status config-files network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-28 22:27:23 status config-files network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 install network-manager-gnome:amd64 0.9.6.2-0ubuntu6 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status half-installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:03 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:06 configure network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:06 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:07 status unpacked network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:07 status half-configured network-manager-gnome:amd64 0.9.6.2-0ubuntu6 2012-10-31 19:58:07 status installed network-manager-gnome:amd64 0.9.6.2-0ubuntu6 ? ~ Unfortunately, I cannot find network-manager-applet package at all: ? ~ apt-cache search network-manager-applet ? ~ Here are the contents of /etc/apt/sources.list: ? ~ cat /etc/apt/sources.list # deb cdrom:[Ubuntu 12.04 LTS _Precise Pangolin_ - Release amd64 (20120425)]/ dists/precise/main/binary-i386/ # deb cdrom:[Ubuntu 12.04 LTS _Precise Pangolin_ - Release amd64 (20120425)]/ dists/precise/restricted/binary-i386/ # deb cdrom:[Ubuntu 12.04 LTS _Precise Pangolin_ - Release amd64 (20120425)]/ precise main restricted # See http://help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. deb http://gb.archive.ubuntu.com/ubuntu/ quantal main restricted deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal main restricted ## Major bug fix updates produced after the final release of the ## distribution. deb http://gb.archive.ubuntu.com/ubuntu/ quantal-updates main restricted deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal-updates main restricted ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team. Also, please note that software in universe WILL NOT receive any ## review or updates from the Ubuntu security team. deb http://gb.archive.ubuntu.com/ubuntu/ quantal universe deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal universe deb http://gb.archive.ubuntu.com/ubuntu/ quantal-updates universe deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal-updates universe ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team, and may not be under a free licence. Please satisfy yourself as to ## your rights to use the software. Also, please note that software in ## multiverse WILL NOT receive any review or updates from the Ubuntu ## security team. deb http://gb.archive.ubuntu.com/ubuntu/ quantal multiverse deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal multiverse deb http://gb.archive.ubuntu.com/ubuntu/ quantal-updates multiverse deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal-updates multiverse ## N.B. software from this repository may not have been tested as ## extensively as that contained in the main release, although it includes ## newer versions of some applications which may provide useful features. ## Also, please note that software in backports WILL NOT receive any review ## or updates from the Ubuntu security team. deb http://gb.archive.ubuntu.com/ubuntu/ quantal-backports main restricted universe multiverse deb-src http://gb.archive.ubuntu.com/ubuntu/ quantal-backports main restricted universe multiverse deb http://security.ubuntu.com/ubuntu quantal-security main restricted deb-src http://security.ubuntu.com/ubuntu quantal-security main restricted deb http://security.ubuntu.com/ubuntu quantal-security universe deb-src http://security.ubuntu.com/ubuntu quantal-security universe deb http://security.ubuntu.com/ubuntu quantal-security multiverse deb-src http://security.ubuntu.com/ubuntu quantal-security multiverse ## Uncomment the following two lines to add software from Canonical's ## 'partner' repository. ## This software is not part of Ubuntu, but is offered by Canonical and the ## respective vendors as a service to Ubuntu users. # deb http://archive.canonical.com/ubuntu precise partner # deb-src http://archive.canonical.com/ubuntu precise partner ## This software is not part of Ubuntu, but is offered by third-party ## developers who want to ship their latest software. deb http://extras.ubuntu.com/ubuntu quantal main deb-src http://extras.ubuntu.com/ubuntu quantal main ? ~ Right now, I can't think of anything else. Happy to provide more info upon request.

    Read the article

  • Trying to keep up with Technology and Blogging

    - by Dave Campbell
    A little bit of everything... The heading above got changed a bunch during writing and I finally settled on that because this has become a 'stream of consciousness' post... or maybe a stream of UNconsciousness :) If you've noticed, my blogging has been a tad slow this fall. There's been a lot going on personally. But then again, I haven't skipped anybody either. Rather than go through ALL the blogs I have aggregated, and take a week to get to the bottom, at some point in the last year, I had moved the lists around so I now have "SilverlightMVPs", "Very Prolific", "WP7", and "Top Checks". This is a total of about 250 of the more prolific bloggers. Those 250 bloggers have kept me very busy up through about //BUILD. Sometimes it would take all week to go through just that list putting out 13 posts per blog per day... but not anymore. This weekend I made it all the way through the BIG list... close to 700 blogs, and if you read my blog, you know I had one medium day (Saturday), and yesterday was very short. Why is this? To be honest, I don't know... is everybody busy re-tooling, or churning waiting for direction? I have a short list of WinRT/Metro/W8 folks... maybe I need to be pointed to more of them... but my old favorites are not pumping out posts as they have in the past. I said before that I am attracted to Metro, and I've already got My first Metro app post out there, and were it not for working with the new site, I'd have had another out last weekend... so definitely look for more from me in that area. New Site? Did I say 'new site' ? oops... didn't mean to do that, but now that the cat is out of the bag, I may as well continue... While at //BUILD, I discussed a re-tooling of SilverlightCream with lots of folks... probably more than wanted to hear about it to be honest! ... it's needed a facelift, and there's stuff on there that never worked right, plus there's a lot of manual effort that goes into a blog post. In an effort to alleviate all the above, Michael Washington and I have been working on the next iteration of SilverlightCream. Not wanting to lose that branding or mess with any saved links, I decided to change from a somewhat funky name to something more professional. I also decided to put my blog on the site, and tie my main announcement twitter feed to the site as well. The way things sit today, there are 3 different names in those locations and it's gotta be confusing for folks just stumbling in. We're going to do a series of posts talking about the site and the new backend processing (hint: Michael Washington is responsible for it, so you can take a guess at the technology), but for now, we'd like some eyes on the front end of the site, and some submittals using it to see if it falls over somewhere that we haven't tried. So... I'm going to give it up... the new site is Windows Dev News. The Twitter feed is @WindowsDevNews, and the blog will be on the site as well at Windows Dev News Blog. I've got the RSS Feed on Feedburner too, so I think all the nuts and bolts are good to go. The submittal and search pages work, as does the blog page. You'll notice we used the MasterPage from SilverlightCream to get started. That will probably change, but it's just the visual... the content is the important part. Other missing things are the tracking and 'Skim' page that we will eventually have up and running. There are some formatting issues with the blog posts but if you hang in there with me, those will be taken care of. If you're a blogger, please submit through the site and let me know if you find any problems. If you're a reader, please add this feed and site. I'll be duplicating the effort for a while but at some point will stop that foolishness. We won't lose the data from SilverlightCream though, so keep using that as a search resource... I have hopes to pull that database over to WindowsDevNews, or link to it in some manner... that part isn't set in jello yet, but it will not be lost. So there it is... let me know what you think, send me your WinRT/Metro/W8 postings along with your Silverlight and WP7 posts... it's not that different, it's just more. Stay in the 'Light

    Read the article

  • Running Jetty under Windows Azure Using RoleEntryPoint in a Worker Role

    - by Shawn Cicoria
    This post is built upon the work of Mario Kosmiskas and David C. Chou’s prior postings – from here: http://blogs.msdn.com/b/mariok/archive/2011/01/05/deploying-java-applications-in-azure.aspx  http://blogs.msdn.com/b/dachou/archive/2010/03/21/run-java-with-jetty-in-windows-azure.aspx As Mario points out in his post, when you need to have more control over the process that starts, it generally is better left to a RoleEntryPoint capability that as of now, requires the use of a CLR based assembly that is deployed as part of the package to Azure. There were things I liked especially about Mario’s post – specifically, the ability to pull down the JRE and Jetty runtimes at role startup and instantiate the process using the extracted bits.  The way Mario initialized the java process (and Jetty) was to take advantage of a role startup task configured as part of the service definition.  This is a great quick way to kick off processes or tasks prior to your role entry point.  However, if you need access to service configuration values or role events, that’s where RoleEntryPoint comes in.  For this PoC sample I moved the logic for retrieving the bits for the jre and jetty to the worker roles OnStart – in addition to moving the process kickoff to the OnStart method.  The Run method at this point is there to loop and just report the status of the java process. Beyond just making things more parameterized, both Mario’s and David’s articles still form the essence of the approach. The solution that accompanies this post provides all the necessary .NET based Visual Studio project.  In addition, you’ll need: 1. Jetty 7 runtime http://www.eclipse.org/jetty/downloads.php 2. JRE http://www.oracle.com/technetwork/java/javase/downloads/index.html Once you have these the first step is to create archives (zips) of the distributions.  For this PoC, the structure of the archive requires that the root of the archive looks as follows: JRE6.zip jetty---.zip Upload the contents to a storage container (block blob), and for this example I used /archives as the location.  The service configuration has several settings that allow, which is the advantage of using RoleEntryPoint, the ability to provide these things via native configuration support from Azure in a worker role. Storage Explorer You can use development storage for testing this out – the zipped version of the solution is configured for development storage.  When you’re ready to deploy, you update the two settings – 1 for diagnostics and the other for the storage container where the /archives are going to be stored. <?xml version="1.0" encoding="utf-8"?> <ServiceConfiguration serviceName="HostedJetty" osFamily="2" osVersion="*"> <Role name="JettyWorker"> <Instances count="1" /> <ConfigurationSettings> <!--<Setting name="Microsoft.WindowsAzure.Plugins.Diagnostics.ConnectionString" value="DefaultEndpointsProtocol=https;AccountName=<accountName>;AccountKey=<accountKey>" />--> <Setting name="Microsoft.WindowsAzure.Plugins.Diagnostics.ConnectionString" value="UseDevelopmentStorage=true" /> <Setting name="JettyArchive" value="jetty-distribution-7.3.0.v20110203b.zip" /> <Setting name="StartRole" value="true" /> <Setting name="BlobContainer" value="archives" /> <Setting name="JreArchive" value="jre6.zip" /> <!--<Setting name="StorageCredentials" value="DefaultEndpointsProtocol=https;AccountName=<accountName>;AccountKey=<accountKey>"/>--> <Setting name="StorageCredentials" value="UseDevelopmentStorage=true" />   For interacting with Storage you can use several tools – one tool that I like is from the Windows Azure CAT team located here: http://appfabriccat.com/2011/02/exploring-windows-azure-storage-apis-by-building-a-storage-explorer-application/  and shown in the prior picture At runtime, during role initialization and startup, Azure will call into your RoleEntryPoint.  At that time the code will do a dynamic pull of the 2 archives and extract – using the Sharp Zip Lib <link> as Mario had demonstrated in his sample.  The only different here is the use of CLR code vs. PowerShell (which is really CLR, but that’s another discussion). At this point, once the 2 zips are extracted, the Role’s file system looks as follows: Worker Role approot From there, the OnStart method (which also does the download and unzip using a simple StorageHelper class) kicks off the Java path and now you have Java! Task Manager Jetty Sample Page A couple of things I’m working on to enhance this is to extract the jre and jetty bits not to the appRoot but to a resource location defined as part of the service definition. ServiceDefinition.csdef <?xml version="1.0" encoding="utf-8"?> <ServiceDefinition name="HostedJetty" xmlns="http://schemas.microsoft.com/ServiceHosting/2008/10/ServiceDefinition"> <WorkerRole name="JettyWorker"> <Imports> <Import moduleName="Diagnostics" /> <Import moduleName="RemoteAccess" /> <Import moduleName="RemoteForwarder" /> </Imports> <Endpoints> <InputEndpoint name="JettyPort" protocol="tcp" port="80" localPort="8080" /> </Endpoints> <LocalResources> <LocalStorage name="Archives" cleanOnRoleRecycle="false" sizeInMB="100" /> </LocalResources>   As the concept matures a bit, being able to update dynamically the content or jar files as part of a running java solution is something that is possible through continued enhancement of this simple model. The Visual Studio 2010 Solution is located here: HostingJavaSln_NDA.zip

    Read the article

  • Going to the Score Cards - Exceptional DBA Awards 2011

    - by Rodney
    This year marks my 4th year as a judge for the Exceptional DBA Awards, founded by Red Gate in 2008 to "recognize the essential but often overlooked contributions of DBAs, the unsung heroes of the IT community." As a professional DBA myself I have been honored to participate as a judge. It is not an easy job because there is a voluminous amount of nominees from all over the world. Each judge has to read through every word of the nominee's answers, deciding what makes each person special and stand out amongst their peers. What drives them? What single element of their submission will shine above all others? It is my hope that what I am about to divulge to you as a judge will prompt you to think about yourself or someone you know and decide that you may be the exceptional DBA who can take home the gold at this year's award ceremony in Seattle. We are more than a few weeks into the nomination process and there are quite a number of submissions already. I can not tell you how many as that would not be fair. I can say it is not 1 million or more. I can also say that it is not 100,000. But that is all I can say about that. However, I can tell you that it is enough this year that we are breaking records on the number of people who have been influenced, inspired or intrigued by the awards in the past. I remember them all like it were yesterday. fuzzy thought cloud here. It was a rainy day in Seattle (all memories for each award ceremony will start thusly) and I was in the hotel going over my notes on what I wanted to say about the winner of the 2008 Red Gate Exceptional DBA Award. The notes were on index cards that I had either bought or stolen from my wife, I do not recall, but I was nervous which was unlike me. This was, after all, a big night for the winner. Of course, we, the judges and the SQL community, had already decided the winner and now all that remained was to present the award. The room was packed. It was Casino night, sponsored by sqlservercentral.com. Money (fake), drinks (not fake) and camaraderie flowed through the room. Dan McClain won the award that year. He worked for Anheuser-Busch at the time. I promise that did not influence my decision. We presented Dan with the award. He was very proud of this achievement, rightfully so, as was the SQL community for him. I spoke with Dan throughout the conference and realized how huge this award was for him, not just personally but professionally. It was a rainy day in Seattle in 2009 and I was nervous. I was asked to speak to a group of people again as a judge for the Exceptional DBA Awards. This year, Josef Richberg would be the recipient of the award, but he would not be able to attend. We all prayed for him as he fought through an illness and congratulated him for his accomplishments as a DBA for his company. He got better and sallied forth and continued to give back to the SQL community that he saw as one big family. In 2010, and I am getting ahead of myself, he was asked to be a judge himself for the very award he had just received the year before. It was a sunny day in Seattle and I missed it, because it was in July and I was not there. It was a rainy day in Seattle and it is 2010 and Tracy Hamlin enters a submission that blows this judge away. She is managing a 50 Terabyte distributed database ("50 Gigabytes! Are you kidding me!!!", Rodney jokes.)  and loves her daily job as a DBA working with developers, mentoring them and teaching them best practices with kindness and patience. She is a people person who just happens to have 10+ years experience with RDBMS'. She wins the award and goes on to be recognized as famous at PASS. It will be a rainy day in Seattle this year when I sit amongst my old constituent judges and friends, Brad McGehee, http://www.simple-talk.com/books/sql-books/how-to-become-an-exceptional-dba,-2nd-edition/, Steve Jones, whom we all know and love at http://www.sqlservercentral.com and a young upstart to the SQL Community, this cat named Brent Ozar to announce the 2011 winner. I personally have not heard of Brent but I am told I have interviewed him for a DBA position several years ago and turned him down, http://www.brentozar.com/archive/2011/05/exceptional-dba-contest/ . I hope that did not jeopardize his future in the SQL world. I am a big hearted oaf and would feel horrible. Hopefully I will meet him at PASS and we can work this all out and I can help him get a DBA job. The rain has stopped and a new year is upon us. The stakes are high...the competition is fierce...the rewards are incredible. The entry form awaits you. http://www.exceptionaldba.com/ I very much look forward to meeting you and presenting the award to you in front of hundreds of your envious but proud peers as the new Exceptional DBA for 2011 at the PASS Summit. Here is what you could win: The Exceptional DBA of the Year receives full conference registration for the 2011 PSS Summit in Seattle, where the awards ceremony will take place, four nights' hotel accommodation, and $300 towards travel expenses. They will also be featured on Simple-Talk. Are you ready? Are you nervous?

    Read the article

  • The standards that fail us and the intellectual bubble

    - by Jeff
    There has been a great deal of noise in the techie community about standards, and a sudden and unexplainable hate for Flash. This noise isn't coming from consumers... the countless soccer moms, teens and your weird uncle Bob, it's coming from the people who build (or at least claim to build) the stuff those consumers consume. If you could survey the position of consumers on the topic, they'd likely tell you that they just want stuff on the Web to work.The noise goes something like this: Web standards are the correct and right thing to use across the Intertubes, and anything not a part of those standards (Flash) is bad. Furthermore, the more recent noise is centered around the idea that HTML 5, along with Javascript, is the right thing to use. The arguments against Flash are, well, the truth is I haven't seen a good argument. I see anecdotal nonsense about high CPU usage and things I'd never think to check when I'm watching Piano Cat on YouTube, but these aren't arguments to me. Sure, I've seen it crash a browser a few times, but it's totally rare.But let's go back to standards. Yes, standards have played an important role in establishing the ubiquity of the Web. The protocols themselves, TCP/IP and HTTP, have been critical. HTML, which has served us well for a very long time, established an incredible foundation. Javascript did an OK job, and thanks to clever programmers writing great frameworks like JQuery, is becoming more and more useful. CSS is awful (there, I said it, I feel SO much better), and I'll never understand why it's so disconnected and different from anything else. It doesn't help that it's so widely misinterpreted by different browsers. Still, there's no question that standards are a good thing, and they've been good for the Web, consumers and publishers alike.HTML 4 has been with us for more than a decade. In Web years, that might as well be 80. HTML 5, contrary to popular belief, is not a standard, and likely won't be for many years to come. In fact, the Web hasn't really evolved at all in terms of its standards. The tools that generate the standard markup and script have, but at the end of the day, we're still living with standards that are more than ten years old. The "official" standards process has failed us.The Web evolved anyway, and did not wait for standards bodies to decide what to do next. It evolved in part because Macromedia, then Adobe, kept evolving Flash. In the earlier days, it mostly just did obnoxious splash pages, but then it started doing animation, and then rich apps as they added form input. Eventually it found its killer app: video. Now more than 95% of browsers have Flash installed. Consumers are better for it.But I'll do it one better... I'll go out on a limb and say that Flash is a standard. If it's that pervasive, I don't care what you tell me, it's a standard. Just because a company owns it doesn't mean that it's evil or not a standard. And hey, it pains me to say that as a developer, because I think the dev tools are the suck (more on that in a minute). But again, consumers don't care. They don't even pay for Flash. The bottom line is that if I put something Flash based on the Internet, it's likely that my audience will see it.And what about the speed of standards owned by a company? Look no further than Silverlight. Silverlight 2 (which I consider the "real" start to the story) came out about a year and a half ago. Now version 4 is out, and it has come a very long way in its capabilities. If you believe Riastats.com, more than half of browsers have it now. It didn't have to wait for standards bodies and nerds drafting documents, it's out today. At this rate, Silverlight will be on version 6 or 7 by the time HTML 5 is a ratified standard.Back to the noise, one of the things that has continually disappointed me about this profession is the number of people who get stuck in an intellectual bubble, color it with dogmatic principles, and completely ignore the actual marketplace where this stuff all has to live. We aren't machines; Binary thinking that forces us to choose between "open standards" and "proprietary lock-in" (the most loaded b.s. FUD term evar) isn't smart at all. The truth is that the <object> tag has allowed us to build incredible stuff on top of the old standards, and consumers have benefitted greatly. Consumer desire, capitalism, and yes, standards ratified by nerds who think about this stuff for years have all played a role in the broad adoption of the Interwebs.We could all do without the noise. At the end of the day, I'm going to build stuff for the Web that's good for my users, and I'm not going to base my decisions on a techie bubble religion. Imagine what the brilliant minds behind the noise could do for the Web if they joined me in that pursuit.

    Read the article

  • iPack -The iOS Application Packager

    - by user13277780
    iOS applications are distributed in .ipa archive files. These files are regular zip files which contain application resources and executable-s. To protect them from unauthorized modifications and to provide identification of their sources, the content of the archives is signed. The signature is included in the application executable of an.ipa archive and protects the executable file itself and the associated resource files. Apple provides native Mac OS tools for signing iOS executable-s (which are actually generic Mach-O code signing tools), but these tools are not generally available on other platforms. To provide a multi-platform development environment for JavaFX based iOS applications, we ported iOS signing and packaging to Java and created a dedicated ipack tool for it. The iPack tool can be used as a last step of creating .ipa package on various operating systems. Prototype has been tested by creating a final distributable for JavaFX application that runs on iPad, all done on Windows 7. Source Code The source code of iPac tool is in OpenJFX project repository. You can find it in: <openjfx root>/rt/tools/ios/Maven/ipack To build the iPack tool use: rt/tools/ios/Maven/ipack$ mvn package After building, you can run the tool: java -jar <path to ipack.jar> <arguments>  Signing keystore The tool uses a java key store to read the signing certificate and the associated private key. To prepare such keystore users can use keytool from JDK. One possible scenario is to import an existing private key and the certificate from a key store used on Mac OS: To list the content of an existing key store and identify the source alias: keytool -list -keystore <src keystore>.p12 -storetype pkcs12 -storepass <src keystore password> To create Java key store and import the private key with its certificate to the keys store: keytool -importkeystore \ -destkeystore <dst keystore> -deststorepass <dst keystore password> \ -srckeystore <src keystore>.p12 -srcstorepass <src keystore password> -srcstoretype pkcs12 \ -srcalias <src alias> -destalias <dst alias> -destkeypass <dst key password> Another scenario would be to generate a private / public key pair directly in a Java key store and create a certificate request from it. After sending the request to Apple one can then import the certificate response back to the Java key store and complete the signing certificate entry. In both scenarios the resulting alias in the Java key store will contain only a single (leaf) certificate. This can be verified with the following command: keytool -list -v -keystore <ipack keystore> -storepass <keystore password> When looking at the Certificate chain length entry, the number next to it is 1. When an executable file is signed on Mac OS, the resulting signature (in CMS format) includes the whole certificate chain up to the Apple Root CA. The ipack tool includes only the chain which is stored under the alias specified on the command line. So to have the whole chain in the signature we need to replace the single certificate entry under the alias with the corresponding full certificate chain. To do that we need first to create the chain in a separate file. It is easy to create such chain when working with certificates in Base-64 encoded PEM format. A certificate chain can be created by concatenating PEM certificates, which should form the chain, into a single file. For iOS signing we need the following certificates in our chain: Apple Root CA Apple Worldwide Developer Relations CA Our signing leaf certificate To convert a certificate from the binary DER format (.der, .cer) to PEM format: keytool -importcert -noprompt -keystore temp.ks -storepass temppwd -alias tempcert -file <certificate>.cer keytool -exportcert -keystore temp.ks -storepass temppwd -alias tempcert -rfc -file <certificate>.pem To export the signing certificate into PEM format: keytool -exportcert -keystore <ipack keystore> -storepass <keystore password> -alias <signing alias> -rfc -file SigningCert.pem After constructing a chain from AppleIncRootCertificate.pem, AppleWWDRCA.pem andSigningCert.pem, it can be imported back into the keystore with: keytool -importcert -noprompt -keystore <ipack keystore> -storepass <keystore password> -alias <signing alias> -keypass <key password> -file SigningCertChain.pem To summarize, the following example shows the full certificate chain replacement process: keytool -importcert -noprompt -keystore temp.ks -storepass temppwd -alias tempcert1 -file AppleIncRootCertificate.cer keytool -exportcert -keystore temp.ks -storepass temppwd -alias tempcert1 -rfc -file AppleIncRootCertificate.pem keytool -importcert -noprompt -keystore temp.ks -storepass temppwd -alias tempcert2 -file AppleWWDRCA.cer keytool -exportcert -keystore temp.ks -storepass temppwd -alias tempcert2 -rfc -file AppleWWDRCA.pem keytool -exportcert -keystore ipack.ks -storepass keystorepwd -alias mycert -rfc -file SigningCert.pem cat SigningCert.pem AppleWWDRCA.pem AppleIncRootCertificate.pem >SigningCertChain.pem keytool -importcert -noprompt -keystore ipack.ks -storepass keystorepwd -alias mycert -keypass keypwd -file SigningCertChain.pem keytool -list -v -keystore ipack.ks -storepass keystorepwd Usage When the ipack tool is started with no arguments it prints the following usage information: -appname MyApplication -appid com.myorg.MyApplication     Usage: ipack <archive> <signing opts> <application opts> [ <application opts> ... ] Signing options: -keystore <keystore> keystore to use for signing -storepass <password> keystore password -alias <alias> alias for the signing certificate chain and the associated private key -keypass <password> password for the private key Application options: -basedir <directory> base directory from which to derive relative paths -appdir <directory> directory with the application executable and resources -appname <file> name of the application executable -appid <id> application identifier Example: ipack MyApplication.ipa -keystore ipack.ks -storepass keystorepwd -alias mycert -keypass keypwd -basedir mysources/MyApplication/dist -appdir Payload/MyApplication.app -appname MyApplication -appid com.myorg.MyApplication    

    Read the article

  • Planning an Event&ndash;SPS NYC

    - by MOSSLover
    I bet some of you were wondering why I am not going to any events for the most part in June and July (aside from volunteering at SPS Chicago).  Well I basically have no life for the next 2 months.  We are approaching the 11th hour of SharePoint Saturday New York City.  The event is slated to have 350 to 400 attendees.  This is second year in a row I’ve helped run it with Jason Gallicchio.  It’s amazingly crazy how much effort this event requires versus Kansas City.  It’s literally 2x the volume of attendees, speakers, and sponsors plus don’t even get me started about volunteers.  So here is a bit of the break down… We have 30 volunteers+ that Tasha Scott from the Hampton Roads Area will be managing the day of the event to do things like timing the speakers, handing out food, making sure people don’t walk into the event that did not sign up until we get a count for fire code, registering people, watching the sharpees, watching the prizes, making sure attendees get to the right place,  opening and closing the partition in the big room, moving chairs, moving furniture, etc…Then there is Jason, Greg, and I who will be making sure that the speakers, sponsors, and everything is going smoothly in the background.  We need to make sure that everything is setup properly and in the right spot.  We also need to make sure signs are printed, schedules are created, bags are stuffed with sponsor material.  Plus we need to send out emails to sponsors reminding them to send us the right information to post on the site for charity sessions, send us boxes with material to stuff bags, and we need to make sure that Michael Lotter gets there information for invoicing.  We also need to check that Michael has invoiced everyone and who has paid, because we can’t order anything for the event without money.  Once people have paid we need to setup food orders, speaker and volunteer dinners, buy prizes, buy bags, buy speakers/volunteer/organizer shirts, etc…During this process we need all the abstracts from speakers, all the bios, pictures, shirt sizes, and other items so we can create schedules and order items.  We also need to keep track of who is attending the dinner the night before for volunteers and speakers and make sure we don’t hit capacity.  Then there is attendee tracking and making sure that we don’t hit too many attendees.  We need to make sure that attendees know where to go and what to do.  We have to make all kinds of random supply lists during this process and keep on track with a variety of lists and emails plus conference calls.  All in all it’s a lot of work and I am trying to keep track of it all the top so that we don’t duplicate anything or miss anything.  So basically all in all if you don’t see me around for another month don’t worry I do exist. Right now if you look at what I’m doing I am traveling every Monday morning and Thursday night back and forth to Washington DC from New Jersey.  Every night I am working on organizational stuff for SharePoint Saturday New York City.  Every Tuesday night we are running an event conference call.  Every weekend I am either with family or my boyfriend and cat trying hard not to touch the event.  So all my time is pretty much work, event, and family/boyfriend.  I have 0 bandwidth for anything in the community.  If you compound that with my severe allergy problems in DC and a doctor’s appointment every month plus a new med once a week I’m lucky I am still standing and walking.  So basically once July 30th hits hopefully Jason Gallicchio, Greg Hurlman, and myself will be able to breathe a little easier.  If I forget to do this thank you Greg and Jason.  Thank you Tom Daly.  Thank you Michael Lotter.  Thank you Tasha Scott.  Thank you Kevin Griffin.  Thank you all the volunteers, speakers, sponsors, and attendees who will and have made this event a success.  Hopefully, we have enough time until next year to regroup, recharge, and make the event grow bigger in a different venue.  Awesome job everyone we sole out within 3 days of registration and we still have several weeks to go.  Right now the waitlist is at 49 people with room to grow.  If you attend the event thank all these guys I mentioned above for making it possible.  It’s going to be awesome I know it but I probably won’t remember half of it due to the blur of things that we will all be taking care of the day of the event.  Catch you all in the end of July/Early August where I will attempt to post something useful and clever and possibly while wearing a fez. Technorati Tags: SPS NYC,SharePoint Saturday,SharePoint Saturday New York City

    Read the article

  • 2011 The Year of Awesomesauce

    - by MOSSLover
    So I was talking to one of my friends, Cathy Dew, and I’m wondering how to start out this post.  What kind of title should I put?  Somehow we’re just randomly throwing things out and this title pops into my head the one you see above. I woke up today to the buzz of a text message.  I spent New Years laying around until 3 am watching Warehouse 13 Episodes and drinking champagne.  It was one of the best New Year’s I spent with my boyfriend and my cat.  I figured I would sleep in until Noon, but ended up waking up around 11:15 to that text message buzz.  I guess my DE, Rachel Appel, had texted me “Happy New Years”, because Rachel is that kind of person.  I immediately proceeded to check my email.  I noticed my live account had a hit.  The account I rarely ever use had an email.  I sort of had that sinking suspicion I was going to get Silverlight MVP right?  So I open the email and something out of the blue happens it says “blah blah blah SharePoint Server MVP blah blah…”.  I’m sitting here a little confused what?  Really?  Just about when you give up on something the unexplained happens.  I am grateful for what I have every day. So let me tell you a story.  I was a senior in high school and it was December 31st, 1999.  A couple days prior my grandmother was complaining she had a cold and her assisted living facility was not going to let her see a doctor.  She claimed to be very sick.  New Year’s Eve Day 1999 my grandmother was rushed to the hospital sometime very early in the morning.  My uncle, my little brother, and myself were sitting in the waiting room eagerly awaiting news.  The Sydney Opera House was playing in the background as New Years 2000 for Australia was ringing in.  They come out and they tell us my grandmother has pneumonia.  She is in the ICU in critical condition.  Eventually time passes in the day and my parents take my brother and I home.  So in the car we had a huge fight that ended in the worst new years of my life.  The next 30 days were the worst 30 days of my life.  I went to the hospital every single day to do my homework and watch my grandmother.  Each day was a challenge mentally and physically as my grandmother berated me in her demented state.  On the 30th day my grandmother ended up in critical condition in the ICU maxed out on painkillers.  At approximately 3 am I hear my parents telling me they don’t want to wake me up and that my grandmother had passed away.  I must have cried more collectively that day than any other day in my life.  Every New Years Even since I have cried thinking about who she was and what she represented.  She was human looking back she wasn’t anything great, but she was one of the positive lights in my life.  Her and my dad and my other grandmother constantly tried to make me feel great when my mother was telling me the opposite.  I’d like to think since 2000 the past 11 years have been the best 11 years of my life.  I got out of a bad situation by using the tools that I had in front of me.  Good grades and getting into a college so I could aspire to be the person that I wanted to be.  I had some great people along the way to help me out. So getting to the point I like to help people further there lives somehow in the best way I can possibly help out.  This New Years was one of the great years that helped me forget the past and focus on the present.  It makes me realize how far I’ve come since high school and even since college.  The one thing I’ve been grappling with over the years is how do you feel good about making money while helping others out.  I’d to think I try really hard to give back to my community.  I could not have done what I did without other people’s help.  I sent out an email prior to even announcing I got the award today.  I can’t say I did everything on my own.  It’s not possible.  I had the help of others every step of the way.  I’m not sure if this makes sense but the award can’t just be mine.  This award is really owned by each and everyone who helped me get here.  From my dad to my grandmother to Rachel Appel to Bob Hunt to Jason Gallicchio to Cathy Dew to Mark Rackley to Johnny Ennion to Lee Brandt to Jeff Julian to John Alexander to Lori Gowin and to many others.  Thank you guys for all the help and support. Technorati Tags: SharePoint Community,MVP Award,Microsoft Community

    Read the article

  • Many Different Things Rolled into a Ball

    - by MOSSLover
    Yeah I know I don’t blog much anymore, because life has taken me places that don’t involve the interwebs unfortunately.  I am in the midst of planning two events, starting a non for profit, creating more sessions for various conferences, submitting to various conferences, working a 40 hour a week job, attempting to hang out with boyfriend/friends/family.  So you can see that list does not include this blog sadly that’s how it goes sometimes.  The bottom piece very important over any of the top pieces.  I haven’t seen St. Louis in a while and I get to go back.  I was gone from home for MVP Summit and Best Practices Conference, so the boyfriend and cat didn’t get to see me either for a bit.  Then you have to add in the whole toilet being broken fiasco this week.  Maintenance really thought it would be cool to turn off the ability to flush.  I mean who does that?  Then when we call the owner he comes by turns it on and we figure it was an accident, because well the next day no one came by to tell us there was a leak.  It was all kinds of strangeness and involved me running to other people’s toilets.  As Dan Usher would say, I was a sad panda for a few days.  So I guess I wanted to post a few thoughts here just because I can.  I do not like multiple content editor webparts embedded with html files in numerous pages doing the same thing.  I will tell you why I don’t like these particular webparts and the way they are being used.  First off if you have a bunch of pages with script includes it’s about time you should just dump them into the masterpage.  Why bother finding all 20 pages and changing those pages when you can just use a single masterpage that already exists? The other thing that is bothering me days is screen scraping.  Just don’t do it, because in 2010 you will find the UI is substantially slower.  I understand you are new and you have no idea what to do.  You are also using 2007 am I right?  So then you need to go to codeplex.com and type in a search for SPServices.  Download it, use it, love it and then have it’s babies (well maybe don’t go so far this is not the GRID in Tron). If you have a ton of constants in your code why did you not go in and create a webpart with a bunch of properties and/or link to a configuration list hidden in the browser?  This type of property and list could help you out in the long run.  The power users and administrators can now change the control without you having to compile it over and over again.  It’s good stuff.  Also, you can change the control without compiling it, especially in 2007 where you have to do a farm solution.  In 2010 you can do a sandbox solution I guess, but shouldn’t you make it as easy and supportable as possible for other users? In conclusion I’m an angry person when it comes to viewing something repeatedly and analyzing it in a system.  Now we will move on to the next topic…MVP Summit…So yeah I can’t really talk about particulars, but I can talk about my experience as a person.  Don’t build something up to be cooler than it is only to be dropped from your 10,000 foot perch.  My experience was great, but the content overall was something to be desired.  It’s ok I got to meet a lot of people I would not have met if I had not gone.  Some of it was surreal, such as product group members showing up and talking to us.  It was pretty neat.  Plus I never had the chance to get to that mythical MS Office in Redmond.  Prior to Summit it was like Rainbow Brites unicorn trying taunting me on television when I was a kid.  So I guess with all that said I give it a B.  It was awesome in some way, but lacking in other ways.  The cool part is that I got to go.  Would I have lived without going? Yes, but it was still cool. I could prattle on about other things and make this post massive, but I’m going to pass and give myself a piece of Sunday to play Rockband and do 800 other things.  I hope the two of you who read this blog are well.  I’ll catch you all at another juncture.  Have a good weekend and varying holidays in between. Technorati Tags: SharePoint,MVP Summit,JQuery,Javascript

    Read the article

  • Unable to keep the connecting using a wireless bridge

    - by dan
    I am running Ubuntu 12.04 on a dell inspiron desktop (core 2 duo) and am using wicd to manage my network/wifi. I've found that the WiFi card in the machine has trouble staying connected to my router (I believe this is a function of distance between the two), so I've taken an old Belkin F5d7231 wireless router and installed dd-wrt on it to use as a wireless bridge hoping that it will have better reception. I think everything up through the wireless bridge is working OK since I have no problems accessing the internet through it with my MacBook. The problem arises when I try to hook the ubuntu machine up to the wireless bridge. It will connect for a few minutes, but it will quickly disconnect without clear triggering event; it may be more likely to disconnect if there is a heavy traffic load going over it (could be something as simple as "cat big_text_file" in an ssh session). I've tried switching from dhclient to dhcpcd without much improvement. Here is the output from the syslog when it connects: Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28278]: wlan1: exiting Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28312]: eth0: exiting Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:08 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:10:08 Chicabuntu kernel: [15184.976127] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.010805] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: dhcpcd not running Jun 30 17:10:08 Chicabuntu dhcpcd[28347]: eth0: exiting Jun 30 17:10:08 Chicabuntu kernel: [15185.180156] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:10:08 Chicabuntu kernel: [15185.212785] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:10:10 Chicabuntu kernel: [15187.027445] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:10:10 Chicabuntu kernel: [15187.027452] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:10:10 Chicabuntu kernel: [15187.028300] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: dhcpcd 3.2.3 starting Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: hardware address = 00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: DUID = 00:01:00:01:17:81:85:79:00:1c:c4:31:1a:83 Jun 30 17:10:10 Chicabuntu dhcpcd[28353]: eth0: broadcasting for a lease Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:10:11 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:10:20 Chicabuntu kernel: [15197.568016] eth0: no IPv6 routers present Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: offered 192.168.1.111 from 192.168.1.254 Jun 30 17:10:29 Chicabuntu dhcpcd[28353]: eth0: checking 192.168.1.111 is available on attached networks Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: leased 192.168.1.111 for 86400 seconds Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding IP address 192.168.1.111/24 Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: adding default route via 192.168.1.254 metric 0 Jun 30 17:10:30 Chicabuntu dhcpcd[28353]: eth0: exiting Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv4 for mDNS. Jun 30 17:10:30 Chicabuntu avahi-daemon[1041]: Registering new address record for 192.168.1.111 on eth0.IPv4. Jun 30 17:10:30 Chicabuntu dhcpcd.sh: interface eth0 has been configured with new IP=192.168.1.111 Jun 30 17:10:39 Chicabuntu ntpdate[28439]: adjust time server 91.189.94.4 offset 0.001915 sec And here is the syslog from when it shuts down the connection without reason: Jun 30 17:12:15 Chicabuntu kernel: [15312.575455] tg3 0000:3f:00.0: eth0: Link is down Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: sending signal 1 to pid 28361 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: received SIGHUP, releasing lease Jun 30 17:12:16 Chicabuntu dhcpcd[28603]: eth0: exiting Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for 192.168.1.111 on eth0. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.1.111. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing default route via 192.168.1.254 metric 0 Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:16 Chicabuntu avahi-daemon[1041]: Withdrawing address record for fe80::21c:c4ff:fe31:1a83 on eth0. Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: No such process Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: removing IP address 192.168.1.111/24 Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: netlink: Cannot assign requested address Jun 30 17:12:16 Chicabuntu dhcpcd[28361]: eth0: exiting Jun 30 17:12:16 Chicabuntu dhcpcd.sh: interface eth0 has been brought down Jun 30 17:12:17 Chicabuntu kernel: [15313.612141] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.644703] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28674]: wlan1: exiting Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: dhcpcd not running Jun 30 17:12:17 Chicabuntu dhcpcd[28708]: eth0: exiting Jun 30 17:12:17 Chicabuntu kernel: [15313.912147] tg3 0000:3f:00.0: irq 44 for MSI/MSI-X Jun 30 17:12:17 Chicabuntu kernel: [15313.944746] ADDRCONF(NETDEV_UP): eth0: link is not ready Jun 30 17:12:18 Chicabuntu kernel: [15315.592569] tg3 0000:3f:00.0: eth0: Link is up at 100 Mbps, full duplex Jun 30 17:12:18 Chicabuntu kernel: [15315.592576] tg3 0000:3f:00.0: eth0: Flow control is on for TX and on for RX Jun 30 17:12:18 Chicabuntu kernel: [15315.593399] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::21c:c4ff:fe31:1a83. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: New relevant interface eth0.IPv6 for mDNS. Jun 30 17:12:20 Chicabuntu avahi-daemon[1041]: Registering new address record for fe80::21c:c4ff:fe31:1a83 on eth0.*. Jun 30 17:12:29 Chicabuntu kernel: [15325.680019] eth0: no IPv6 routers present If this isn't useful, I can also post the wicd log, but that is kind of long. If anyone could help me I would be eternally grateful.

    Read the article

  • Rkhunter 122 suspect files; do I have a problem?

    - by user276166
    I am new to ubuntu. I am using Xfce Ubuntu 14.04 LTS. I have ran rkhunter a few weeks age and only got a few warnings. The forum said that they were normal. But, this time rkhunter reported 122 warnings. Please advise. casey@Shaman:~$ sudo rkhunter -c [ Rootkit Hunter version 1.4.0 ] Checking system commands... Performing 'strings' command checks Checking 'strings' command [ OK ] Performing 'shared libraries' checks Checking for preloading variables [ None found ] Checking for preloaded libraries [ None found ] Checking LD_LIBRARY_PATH variable [ Not found ] Performing file properties checks Checking for prerequisites [ Warning ] /usr/sbin/adduser [ Warning ] /usr/sbin/chroot [ Warning ] /usr/sbin/cron [ OK ] /usr/sbin/groupadd [ Warning ] /usr/sbin/groupdel [ Warning ] /usr/sbin/groupmod [ Warning ] /usr/sbin/grpck [ Warning ] /usr/sbin/nologin [ Warning ] /usr/sbin/pwck [ Warning ] /usr/sbin/rsyslogd [ Warning ] /usr/sbin/useradd [ Warning ] /usr/sbin/userdel [ Warning ] /usr/sbin/usermod [ Warning ] /usr/sbin/vipw [ Warning ] /usr/bin/awk [ Warning ] /usr/bin/basename [ Warning ] /usr/bin/chattr [ Warning ] /usr/bin/cut [ Warning ] /usr/bin/diff [ Warning ] /usr/bin/dirname [ Warning ] /usr/bin/dpkg [ Warning ] /usr/bin/dpkg-query [ Warning ] /usr/bin/du [ Warning ] /usr/bin/env [ Warning ] /usr/bin/file [ Warning ] /usr/bin/find [ Warning ] /usr/bin/GET [ Warning ] /usr/bin/groups [ Warning ] /usr/bin/head [ Warning ] /usr/bin/id [ Warning ] /usr/bin/killall [ OK ] /usr/bin/last [ Warning ] /usr/bin/lastlog [ Warning ] /usr/bin/ldd [ Warning ] /usr/bin/less [ OK ] /usr/bin/locate [ OK ] /usr/bin/logger [ Warning ] /usr/bin/lsattr [ Warning ] /usr/bin/lsof [ OK ] /usr/bin/mail [ OK ] /usr/bin/md5sum [ Warning ] /usr/bin/mlocate [ OK ] /usr/bin/newgrp [ Warning ] /usr/bin/passwd [ Warning ] /usr/bin/perl [ Warning ] /usr/bin/pgrep [ Warning ] /usr/bin/pkill [ Warning ] /usr/bin/pstree [ OK ] /usr/bin/rkhunter [ OK ] /usr/bin/rpm [ Warning ] /usr/bin/runcon [ Warning ] /usr/bin/sha1sum [ Warning ] /usr/bin/sha224sum [ Warning ] /usr/bin/sha256sum [ Warning ] /usr/bin/sha384sum [ Warning ] /usr/bin/sha512sum [ Warning ] /usr/bin/size [ Warning ] /usr/bin/sort [ Warning ] /usr/bin/stat [ Warning ] /usr/bin/strace [ Warning ] /usr/bin/strings [ Warning ] /usr/bin/sudo [ Warning ] /usr/bin/tail [ Warning ] /usr/bin/test [ Warning ] /usr/bin/top [ Warning ] /usr/bin/touch [ Warning ] /usr/bin/tr [ Warning ] /usr/bin/uniq [ Warning ] /usr/bin/users [ Warning ] /usr/bin/vmstat [ Warning ] /usr/bin/w [ Warning ] /usr/bin/watch [ Warning ] /usr/bin/wc [ Warning ] /usr/bin/wget [ Warning ] /usr/bin/whatis [ Warning ] /usr/bin/whereis [ Warning ] /usr/bin/which [ OK ] /usr/bin/who [ Warning ] /usr/bin/whoami [ Warning ] /usr/bin/unhide.rb [ Warning ] /usr/bin/mawk [ Warning ] /usr/bin/lwp-request [ Warning ] /usr/bin/heirloom-mailx [ OK ] /usr/bin/w.procps [ Warning ] /sbin/depmod [ Warning ] /sbin/fsck [ Warning ] /sbin/ifconfig [ Warning ] /sbin/ifdown [ Warning ] /sbin/ifup [ Warning ] /sbin/init [ Warning ] /sbin/insmod [ Warning ] /sbin/ip [ Warning ] /sbin/lsmod [ Warning ] /sbin/modinfo [ Warning ] /sbin/modprobe [ Warning ] /sbin/rmmod [ Warning ] /sbin/route [ Warning ] /sbin/runlevel [ Warning ] /sbin/sulogin [ Warning ] /sbin/sysctl [ Warning ] /bin/bash [ Warning ] /bin/cat [ Warning ] /bin/chmod [ Warning ] /bin/chown [ Warning ] /bin/cp [ Warning ] /bin/date [ Warning ] /bin/df [ Warning ] /bin/dmesg [ Warning ] /bin/echo [ Warning ] /bin/ed [ OK ] /bin/egrep [ Warning ] /bin/fgrep [ Warning ] /bin/fuser [ OK ] /bin/grep [ Warning ] /bin/ip [ Warning ] /bin/kill [ Warning ] /bin/less [ OK ] /bin/login [ Warning ] /bin/ls [ Warning ] /bin/lsmod [ Warning ] /bin/mktemp [ Warning ] /bin/more [ Warning ] /bin/mount [ Warning ] /bin/mv [ Warning ] /bin/netstat [ Warning ] /bin/ping [ Warning ] /bin/ps [ Warning ] /bin/pwd [ Warning ] /bin/readlink [ Warning ] /bin/sed [ Warning ] /bin/sh [ Warning ] /bin/su [ Warning ] /bin/touch [ Warning ] /bin/uname [ Warning ] /bin/which [ OK ] /bin/kmod [ Warning ] /bin/dash [ Warning ] [Press <ENTER> to continue] Checking for rootkits... Performing check of known rootkit files and directories 55808 Trojan - Variant A [ Not found ] ADM Worm [ Not found ] AjaKit Rootkit [ Not found ] Adore Rootkit [ Not found ] aPa Kit [ Not found ] Apache Worm [ Not found ] Ambient (ark) Rootkit [ Not found ] Balaur Rootkit [ Not found ] BeastKit Rootkit [ Not found ] beX2 Rootkit [ Not found ] BOBKit Rootkit [ Not found ] cb Rootkit [ Not found ] CiNIK Worm (Slapper.B variant) [ Not found ] Danny-Boy's Abuse Kit [ Not found ] Devil RootKit [ Not found ] Dica-Kit Rootkit [ Not found ] Dreams Rootkit [ Not found ] Duarawkz Rootkit [ Not found ] Enye LKM [ Not found ] Flea Linux Rootkit [ Not found ] Fu Rootkit [ Not found ] Fuck`it Rootkit [ Not found ] GasKit Rootkit [ Not found ] Heroin LKM [ Not found ] HjC Kit [ Not found ] ignoKit Rootkit [ Not found ] IntoXonia-NG Rootkit [ Not found ] Irix Rootkit [ Not found ] Jynx Rootkit [ Not found ] KBeast Rootkit [ Not found ] Kitko Rootkit [ Not found ] Knark Rootkit [ Not found ] ld-linuxv.so Rootkit [ Not found ] Li0n Worm [ Not found ] Lockit / LJK2 Rootkit [ Not found ] Mood-NT Rootkit [ Not found ] MRK Rootkit [ Not found ] Ni0 Rootkit [ Not found ] Ohhara Rootkit [ Not found ] Optic Kit (Tux) Worm [ Not found ] Oz Rootkit [ Not found ] Phalanx Rootkit [ Not found ] Phalanx2 Rootkit [ Not found ] Phalanx2 Rootkit (extended tests) [ Not found ] Portacelo Rootkit [ Not found ] R3dstorm Toolkit [ Not found ] RH-Sharpe's Rootkit [ Not found ] RSHA's Rootkit [ Not found ] Scalper Worm [ Not found ] Sebek LKM [ Not found ] Shutdown Rootkit [ Not found ] SHV4 Rootkit [ Not found ] SHV5 Rootkit [ Not found ] Sin Rootkit [ Not found ] Slapper Worm [ Not found ] Sneakin Rootkit [ Not found ] 'Spanish' Rootkit [ Not found ] Suckit Rootkit [ Not found ] Superkit Rootkit [ Not found ] TBD (Telnet BackDoor) [ Not found ] TeLeKiT Rootkit [ Not found ] T0rn Rootkit [ Not found ] trNkit Rootkit [ Not found ] Trojanit Kit [ Not found ] Tuxtendo Rootkit [ Not found ] URK Rootkit [ Not found ] Vampire Rootkit [ Not found ] VcKit Rootkit [ Not found ] Volc Rootkit [ Not found ] Xzibit Rootkit [ Not found ] zaRwT.KiT Rootkit [ Not found ] ZK Rootkit [ Not found ] [Press <ENTER> to continue] Performing additional rootkit checks Suckit Rookit additional checks [ OK ] Checking for possible rootkit files and directories [ None found ] Checking for possible rootkit strings [ None found ] Performing malware checks Checking running processes for suspicious files [ None found ] Checking for login backdoors [ None found ] Checking for suspicious directories [ None found ] Checking for sniffer log files [ None found ] Performing Linux specific checks Checking loaded kernel modules [ OK ] Checking kernel module names [ OK ] [Press <ENTER> to continue] Checking the network... Performing checks on the network ports Checking for backdoor ports [ None found ] Checking for hidden ports [ Skipped ] Performing checks on the network interfaces Checking for promiscuous interfaces [ None found ] Checking the local host... Performing system boot checks Checking for local host name [ Found ] Checking for system startup files [ Found ] Checking system startup files for malware [ None found ] Performing group and account checks Checking for passwd file [ Found ] Checking for root equivalent (UID 0) accounts [ None found ] Checking for passwordless accounts [ None found ] Checking for passwd file changes [ Warning ] Checking for group file changes [ Warning ] Checking root account shell history files [ None found ] Performing system configuration file checks Checking for SSH configuration file [ Not found ] Checking for running syslog daemon [ Found ] Checking for syslog configuration file [ Found ] Checking if syslog remote logging is allowed [ Not allowed ] Performing filesystem checks Checking /dev for suspicious file types [ Warning ] Checking for hidden files and directories [ Warning ] [Press <ENTER> to continue] System checks summary ===================== File properties checks... Required commands check failed Files checked: 137 Suspect files: 122 Rootkit checks... Rootkits checked : 291 Possible rootkits: 0 Applications checks... All checks skipped The system checks took: 5 minutes and 11 seconds All results have been written to the log file (/var/log/rkhunter.log)

    Read the article

  • Agile Testing Days 2012 – My First Conference!

    - by Chris George
    I’d like to give you a bit of background first… so please bear with me! In 1996, whilst studying for my final year of my degree, I applied for a job as a C++ Developer at a small software house in Hertfordshire  After bodging up the technical part of the interview I didn’t get the job, but was offered a position as a QA Engineer instead. The role sounded intriguing and the pay was pretty good so in the absence of anything else I took it. Here began my career in the world of software testing! Back then, testing/QA was often an afterthought, something that was bolted on to the development process and very much a second class citizen. Test automation was rare, and tools were basic or non-existent! The internet was just starting to take off, and whilst there might have been testing communities and resources, we were certainly not exposed to any of them. After 8 years I moved to another small company, and again didn’t find myself exposed to any of the changes that were happening in the industry. It wasn’t until I joined Red Gate in 2008 that my view of testing and software development as a whole started to expand. But it took a further 4 years for my view of testing to be totally blown open, and so the story really begins… In May 2012 I was fortunate to land the role of Head of Test Engineering. Soon after, I received an email with details for the “Agile Testi However, in my new role, I decided that it was time to bite the bullet and at least go to one conference. Perhaps I could get some new ideas to supplement and support some of the ideas I already had.ng Days” conference in Potsdam, Germany. I looked over the suggested programme and some of the talks peeked my interest. For numerous reasons I’d shied away from attending conferences in the past, one of the main ones being that I didn’t see much benefit in attending loads of talks when I could just read about stuff like that on the internet. So, on the 18th November 2012, myself and three other Red Gaters boarded a plane at Heathrow bound for Potsdam, Germany to attend Agile Testing Days 2012. Tutorial Day – “Software Testing Reloaded” We chose to do the tutorials on the 19th, I chose the one titled “Software Testing Reloaded – So you wanna actually DO something? We’ve got just the workshop for you. Now with even less powerpoint!”. With such a concise and serious title I just had to see what it was about! I nervously entered the room to be greeted by tables, chairs etc all over the place, not set out and frankly in one hell of a mess! There were a few people in there playing a game with dice. Okaaaay… this is going to be a long day! Actually the dice game was an exercise in deduction and simplification… I found it very interesting and is certainly something I’ll be using at work as a training exercise! (I won’t explain the game here cause I don’t want to let the cat out of the bag…) The tutorial consisted of several games, exploring different aspects of testing. They were all practical yet required a fair amount of thin king. Matt Heusser and Pete Walen were running the tutorial, and presented it in a very relaxed and light-hearted manner. It was really my first experience of working in small teams with testers from very different backgrounds, and it was really enjoyable. Matt & Pete were very approachable and offered advice where required whilst still making you work for the answers! One of the tasks was to devise several strategies for testing some electronic dice. The premise was that a Vegas casino wanted to use the dice to appeal to the twenty-somethings interested in tech, but needed assurance that they were as reliable and random as traditional dice. This was a very interesting and challenging exercise that forced us to challenge various assumptions, determine/clarify requirements but most of all it was frustrating because the dice made a very very irritating beeping noise. Multiple that by at least 12 dice and I was dreaming about them all that night!! Some of the main takeaways that were brilliantly demonstrated through the games were not to make assumptions, challenge requirements, and have fun testing! The tutorial lasted the whole day, but to be honest the day went very quickly! My introduction into the conference experience started very well indeed, and I would talk to both Matt and Pete several times during the 4 days. Days 1,2 & 3 will be coming soon…  

    Read the article

  • Solaris 11.2: Functional Deprecation

    - by alanc
    In Solaris 11.1, I updated the system headers to enable use of several attributes on functions, including noreturn and printf format, to give compilers and static analyzers more information about how they are used to give better warnings when building code. In Solaris 11.2, I've gone back in and added one more attribute to a number of functions in the system headers: __attribute__((__deprecated__)). This is used to warn people building software that they’re using function calls we recommend no longer be used. While in many cases the Solaris Binary Compatibility Guarantee means we won't ever remove these functions from the system libraries, we still want to discourage their use. I made passes through both the POSIX and C standards, and some of the Solaris architecture review cases to come up with an initial list which the Solaris architecture review committee accepted to start with. This set is by no means a complete list of Obsolete function interfaces, but should be a reasonable start at functions that are well documented as deprecated and seem useful to warn developers away from. More functions may be flagged in the future as they get deprecated, or if further passes are made through our existing deprecated functions to flag more of them. Header Interface Deprecated by Alternative Documented in <door.h> door_cred(3C) PSARC/2002/188 door_ucred(3C) door_cred(3C) <kvm.h> kvm_read(3KVM), kvm_write(3KVM) PSARC/1995/186 Functions on kvm_kread(3KVM) man page kvm_read(3KVM) <stdio.h> gets(3C) ISO C99 TC3 (Removed in ISO C11), POSIX:2008/XPG7/Unix08 fgets(3C) gets(3C) man page, and just about every gets(3C) reference online from the past 25 years, since the Morris worm proved bad things happen when it’s used. <unistd.h> vfork(2) PSARC/2004/760, POSIX:2001/XPG6/Unix03 (Removed in POSIX:2008/XPG7/Unix08) posix_spawn(3C) vfork(2) man page. <utmp.h> All functions from getutent(3C) man page PSARC/1999/103 utmpx functions from getutentx(3C) man page getutent(3C) man page <varargs.h> varargs.h version of va_list typedef ANSI/ISO C89 standard <stdarg.h> varargs(3EXT) <volmgt.h> All functions PSARC/2005/672 hal(5) API volmgt_check(3VOLMGT), etc. <sys/nvpair.h> nvlist_add_boolean(3NVPAIR), nvlist_lookup_boolean(3NVPAIR) PSARC/2003/587 nvlist_add_boolean_value, nvlist_lookup_boolean_value nvlist_add_boolean(3NVPAIR) & (9F), nvlist_lookup_boolean(3NVPAIR) & (9F). <sys/processor.h> gethomelgroup(3C) PSARC/2003/034 lgrp_home(3LGRP) gethomelgroup(3C) <sys/stat_impl.h> _fxstat, _xstat, _lxstat, _xmknod PSARC/2009/657 stat(2) old functions are undocumented remains of SVR3/COFF compatibility support If the above table is cut off when viewing in the blog, try viewing this standalone copy of the table. To See or Not To See To see these warnings, you will need to be building with either gcc (versions 3.4, 4.5, 4.7, & 4.8 are available in the 11.2 package repo), or with Oracle Solaris Studio 12.4 or later (which like Solaris 11.2, is currently in beta testing). For instance, take this oversimplified (and obviously buggy) implementation of the cat command: #include <stdio.h> int main(int argc, char **argv) { char buf[80]; while (gets(buf) != NULL) puts(buf); return 0; } Compiling it with the Studio 12.4 beta compiler will produce warnings such as: % cc -V cc: Sun C 5.13 SunOS_i386 Beta 2014/03/11 % cc gets_test.c "gets_test.c", line 6: warning: "gets" is deprecated, declared in : "/usr/include/iso/stdio_iso.h", line 221 The exact warning given varies by compilers, and the compilers also have a variety of flags to either raise the warnings to errors, or silence them. Of couse, the exact form of the output is Not An Interface that can be relied on for automated parsing, just shown for example. gets(3C) is actually a special case — as noted above, it is no longer part of the C Standard Library in the C11 standard, so when compiling in C11 mode (i.e. when __STDC_VERSION__ >= 201112L), the <stdio.h> header will not provide a prototype for it, causing the compiler to complain it is unknown: % gcc -std=c11 gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: warning: implicit declaration of function ‘gets’ [-Wimplicit-function-declaration] while (gets(buf) != NULL) ^ The gets(3C) function of course is still in libc, so if you ignore the error or provide your own prototype, you can still build code that calls it, you just have to acknowledge you’re taking on the risk of doing so yourself. Solaris Studio 12.4 Beta % cc gets_test.c "gets_test.c", line 6: warning: "gets" is deprecated, declared in : "/usr/include/iso/stdio_iso.h", line 221 % cc -errwarn=E_DEPRECATED_ATT gets_test.c "gets_test.c", line 6: "gets" is deprecated, declared in : "/usr/include/iso/stdio_iso.h", line 221 cc: acomp failed for gets_test.c This warning is silenced in the 12.4 beta by cc -erroff=E_DEPRECATED_ATT No warning is currently issued by Studio 12.3 & earler releases. gcc 3.4.3 % /usr/sfw/bin/gcc gets_test.c gets_test.c: In function `main': gets_test.c:6: warning: `gets' is deprecated (declared at /usr/include/iso/stdio_iso.h:221) Warning is completely silenced with gcc -Wno-deprecated-declarations gcc 4.7.3 % /usr/gcc/4.7/bin/gcc gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: warning: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Wdeprecated-declarations] % /usr/gcc/4.7/bin/gcc -Werror=deprecated-declarations gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: error: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Werror=deprecated-declarations] cc1: some warnings being treated as errors Warning is completely silenced with gcc -Wno-deprecated-declarations gcc 4.8.2 % /usr/bin/gcc gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: warning: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Wdeprecated-declarations] while (gets(buf) != NULL) ^ % /usr/bin/gcc -Werror=deprecated-declarations gets_test.c gets_test.c: In function ‘main’: gets_test.c:6:5: error: ‘gets’ is deprecated (declared at /usr/include/iso/stdio_iso.h:221) [-Werror=deprecated-declarations] while (gets(buf) != NULL) ^ cc1: some warnings being treated as errors Warning is completely silenced with gcc -Wno-deprecated-declarations

    Read the article

  • Battery life starts at 2:30 hrs (99%), but less than 1 minute later is only 1:30 hrs (99%)

    - by zondu
    After searching this and other forums, I haven't seen this same issue listed anywhere for Ubuntu 12. Prior to installing Ubuntu 12.10, my Netbook (Acer AspireOne D250, SATA HDD) was consistently getting 2:30-3 hrs battery life under Windows XP Home, SP3. However, immediately after installing Ubuntu 12.10, the battery life starts out at 2:30 hrs (99%), but less than 1 minute later suddenly drops to 1:30 hrs (99%), which seems very odd. It could be a complete coincidence that the battery is suddenly flaky at the exact same moment that Ubuntu 12.10 was installed, but that doesn't seem likely. I'm a newbie to Ubuntu, so I don't have much experience tweaking/trouble-shooting yet. Here's what I've tried so far: enabled laptop mode (sudo su, then echo 5 /proc/sys/vm/laptop_mode) and checked that it is running when the A/C adapter is unplugged, but it doesn't seem to have made any noticeable difference in battery life, installed Jupiter, but it didn't work and messed up the system, so I had to uninstall it, disabled bluetooth (wifi is still on b/c it is necessary), set the screen to lowest brightness, etc., run through at least 1 full power cycle (running until the netbook shut itself off due to critical battery) and have been using it normally (sometimes plugged in, often unplugged until the battery gets very low) for a week since installing Ubuntu 12.10. installed powertop, but have no idea how to interpret its results. Here are the results of acpi -b: w/ A/C adapter: Battery 0: Full, 100% immediately after unplugging: Battery 0: Discharging, 99%, 02:30:20 remaining 1 minute after unplugging: Battery 0: Discharging, 99%, 01:37:49 remaining 2-3 minutes after unplugging: Battery 0: Discharging, 95%, 01:33:01 remaining 10 minutes after unplugging: Battery 0: Discharging, 85%, 01:13:38 remaining Results of cat /sys/class/power_supply/BAT0/uevent: w/ A/C adapter: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Full POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=12136000 POWER_SUPPLY_CURRENT_NOW=773000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1956000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= immediately after unplugging: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11886000 POWER_SUPPLY_CURRENT_NOW=773000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1937000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= 1 minute later: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11728000 POWER_SUPPLY_CURRENT_NOW=1174000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1937000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= 2-3 minutes later: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11583000 POWER_SUPPLY_CURRENT_NOW=1209000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1878000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= 10 minutes later: POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Discharging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=11230000 POWER_SUPPLY_CURRENT_NOW=1239000 POWER_SUPPLY_CHARGE_FULL_DESIGN=4500000 POWER_SUPPLY_CHARGE_FULL=1956000 POWER_SUPPLY_CHARGE_NOW=1644000 POWER_SUPPLY_MODEL_NAME=UM08B32 POWER_SUPPLY_MANUFACTURER=SANYO POWER_SUPPLY_SERIAL_NUMBER= Results of upower -i /org/freedesktop/UPower/devices/battery_BAT0: w/ A/C adapter: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:24:58 2012 (823 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: fully-charged energy: 21.1248 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 8.3484 W voltage: 12.173 V percentage: 100% capacity: 43.4667% technology: lithium-ion immediately after unplugging: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:41:25 2012 (1 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 20.9196 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 8.3484 W voltage: 11.86 V time to empty: 2.5 hours percentage: 99.0286% capacity: 43.4667% technology: lithium-ion History (charge): 1354023683 99.029 discharging 1 minute later: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:42:31 2012 (17 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 20.9196 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 13.5432 W voltage: 11.753 V time to empty: 1.5 hours percentage: 99.0286% capacity: 43.4667% technology: lithium-ion History (charge): 1354023683 99.029 discharging History (rate): 1354023751 13.543 discharging 2-3 minutes later: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:45:06 2012 (20 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 20.2824 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 13.7484 W voltage: 11.545 V time to empty: 1.5 hours percentage: 96.0123% capacity: 43.4667% technology: lithium-ion History (charge): 1354023906 96.012 discharging 1354023844 97.035 discharging History (rate): 1354023906 13.748 discharging 1354023875 12.992 discharging 1354023844 13.284 discharging 10 minutes later: native-path: /sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0A:00/power_supply/BAT0 vendor: SANYO model: UM08B32 power supply: yes updated: Tue Nov 27 15:54:24 2012 (28 seconds ago) has history: yes has statistics: yes battery present: yes rechargeable: yes state: discharging energy: 18.1764 Wh energy-empty: 0 Wh energy-full: 21.1248 Wh energy-full-design: 48.6 Wh energy-rate: 13.2948 W voltage: 11.268 V time to empty: 1.4 hours percentage: 86.0429% capacity: 43.4667% technology: lithium-ion History (charge): 1354024433 86.043 discharging History (rate): 1354024464 13.295 discharging 1354024433 13.662 discharging 1354024402 13.781 discharging I noticed that between #2 and #3 (0 and 1 minutes after unplugging), while the battery still reports 99% charge and drops from 2:30 hr to 1:30 hr, the energy usage goes from 8.34 W to 13.54 W and the current_now increases, but shouldn't it be using less energy in battery mode since the screen is much dimmer and it's in power saving mode? (or is that normal behavior?) It also seems to drain more quickly than what it predicts, especially with the 1-1.25 hour drop in the first minute of being unplugged, which seems odd. What really concerns me is that Ubuntu 12.10 may not be properly managing the battery (with the sudden change in charge/life from 2:30 to 1:30 or 1:15 within a minute of unplugging), and that a new battery may quickly die under Ubuntu 12.10. I'd greatly appreciate any advice/suggestions on what to do, and especially whether there's a way to get back the 1-1.5 hrs of battery life that were suddenly lost when changing from WinXp to Ubuntu 12.10. Thanks :)

    Read the article

  • Scripting with the Sun ZFS Storage 7000 Appliance

    - by Geoff Ongley
    The Sun ZFS Storage 7000 appliance has a user friendly and easy to understand graphical web based interface we call the "BUI" or "Browser User Interface".This interface is very useful for many tasks, but in some cases a script (or workflow) may be more appropriate, such as:Repetitive tasksTasks which work on (or obtain information about) a large number of shares or usersTasks which are triggered by an alert threshold (workflows)Tasks where you want a only very basic input, but a consistent output (workflows)The appliance scripting language is based on ECMAscript 3 (close to javascript). I'm not going to cover ECMAscript 3 in great depth (I'm far from an expert here), but I would like to show you some neat things you can do with the appliance, to get you started based on what I have found from my own playing around.I'm making the assumption you have some sort of programming background, and understand variables, arrays, functions to some extent - but of course if something is not clear, please let me know so I can fix it up or clarify it.Variable Declarations and ArraysVariablesECMAScript is a dynamically and weakly typed language. If you don't know what that means, google is your friend - but at a high level it means we can just declare variables with no specific type and on the fly.For example, I can declare a variable and use it straight away in the middle of my code, for example:projects=list();Which makes projects an array of values that are returned from the list(); function (which is usable in most contexts). With this kind of variable, I can do things like:projects.length (this property on array tells you how many objects are in it, good for for loops etc). Alternatively, I could say:projects=3;and now projects is just a simple number.Should we declare variables like this so loosely? In my opinion, the answer is no - I feel it is a better practice to declare variables you are going to use, before you use them - and given them an initial value. You can do so as follows:var myVariable=0;To demonstrate the ability to just randomly assign and change the type of variables, you can create a simple script at the cli as follows (bold for input):fishy10:> script("." to run)> run("cd /");("." to run)> run ("shares");("." to run)> var projects;("." to run)> projects=list();("." to run)> printf("Number of projects is: %d\n",projects.length);("." to run)> projects=152;("." to run)> printf("Value of the projects variable as an integer is now: %d\n",projects);("." to run)> .Number of projects is: 7Value of the projects variable as an integer is now: 152You can also confirm this behaviour by checking the typeof variable we are dealing with:fishy10:> script("." to run)> run("cd /");("." to run)> run ("shares");("." to run)> var projects;("." to run)> projects=list();("." to run)> printf("var projects is of type %s\n",typeof(projects));("." to run)> projects=152;("." to run)> printf("var projects is of type %s\n",typeof(projects));("." to run)> .var projects is of type objectvar projects is of type numberArraysSo you likely noticed that we have already touched on arrays, as the list(); (in the shares context) stored an array into the 'projects' variable.But what if you want to declare your own array? Easy! This is very similar to Java and other languages, we just instantiate a brand new "Array" object using the keyword new:var myArray = new Array();will create an array called "myArray".A quick example:fishy10:> script("." to run)> testArray = new Array();("." to run)> testArray[0]="This";("." to run)> testArray[1]="is";("." to run)> testArray[2]="just";("." to run)> testArray[3]="a";("." to run)> testArray[4]="test";("." to run)> for (i=0; i < testArray.length; i++)("." to run)> {("." to run)>    printf("Array element %d is %s\n",i,testArray[i]);("." to run)> }("." to run)> .Array element 0 is ThisArray element 1 is isArray element 2 is justArray element 3 is aArray element 4 is testWorking With LoopsFor LoopFor loops are very similar to those you will see in C, java and several other languages. One of the key differences here is, as you were made aware earlier, we can be a bit more sloppy with our variable declarations.The general way you would likely use a for loop is as follows:for (variable; test-case; modifier for variable){}For example, you may wish to declare a variable i as 0; and a MAX_ITERATIONS variable to determine how many times this loop should repeat:var i=0;var MAX_ITERATIONS=10;And then, use this variable to be tested against some case existing (has i reached MAX_ITERATIONS? - if not, increment i using i++);for (i=0; i < MAX_ITERATIONS; i++){ // some work to do}So lets run something like this on the appliance:fishy10:> script("." to run)> var i=0;("." to run)> var MAX_ITERATIONS=10;("." to run)> for (i=0; i < MAX_ITERATIONS; i++)("." to run)> {("." to run)>    printf("The number is %d\n",i);("." to run)> }("." to run)> .The number is 0The number is 1The number is 2The number is 3The number is 4The number is 5The number is 6The number is 7The number is 8The number is 9While LoopWhile loops again are very similar to other languages, we loop "while" a condition is met. For example:fishy10:> script("." to run)> var isTen=false;("." to run)> var counter=0;("." to run)> while(isTen==false)("." to run)> {("." to run)>    if (counter==10) ("." to run)>    { ("." to run)>            isTen=true;   ("." to run)>    } ("." to run)>    printf("Counter is %d\n",counter);("." to run)>    counter++;    ("." to run)> }("." to run)> printf("Loop has ended and Counter is %d\n",counter);("." to run)> .Counter is 0Counter is 1Counter is 2Counter is 3Counter is 4Counter is 5Counter is 6Counter is 7Counter is 8Counter is 9Counter is 10Loop has ended and Counter is 11So what do we notice here? Something has actually gone wrong - counter will technically be 11 once the loop completes... Why is this?Well, if we have a loop like this, where the 'while' condition that will end the loop may be set based on some other condition(s) existing (such as the counter has reached 10) - we must ensure that we  terminate this iteration of the loop when the condition is met - otherwise the rest of the code will be followed which may not be desirable. In other words, like in other languages, we will only ever check the loop condition once we are ready to perform the next iteration, so any other code after we set "isTen" to be true, will still be executed as we can see it was above.We can avoid this by adding a break into our loop once we know we have set the condition - this will stop the rest of the logic being processed in this iteration (and as such, counter will not be incremented). So lets try that again:fishy10:> script("." to run)> var isTen=false;("." to run)> var counter=0;("." to run)> while(isTen==false)("." to run)> {("." to run)>    if (counter==10) ("." to run)>    { ("." to run)>            isTen=true;   ("." to run)>            break;("." to run)>    } ("." to run)>    printf("Counter is %d\n",counter);("." to run)>    counter++;    ("." to run)> }("." to run)> printf("Loop has ended and Counter is %d\n", counter);("." to run)> .Counter is 0Counter is 1Counter is 2Counter is 3Counter is 4Counter is 5Counter is 6Counter is 7Counter is 8Counter is 9Loop has ended and Counter is 10Much better!Methods to Obtain and Manipulate DataGet MethodThe get method allows you to get simple properties from an object, for example a quota from a user. The syntax is fairly simple:var myVariable=get('property');An example of where you may wish to use this, is when you are getting a bunch of information about a user (such as quota information when in a shares context):var users=list();for(k=0; k < users.length; k++){     user=users[k];     run('select ' + user);     var username=get('name');     var usage=get('usage');     var quota=get('quota');...Which you can then use to your advantage - to print or manipulate infomation (you could change a user's information with a set method, based on the information returned from the get method). The set method is explained next.Set MethodThe set method can be used in a simple manner, similar to get. The syntax for set is:set('property','value'); // where value is a string, if it was a number, you don't need quotesFor example, we could set the quota on a share as follows (first observing the initial value):fishy10:shares default/test-geoff> script("." to run)> var currentQuota=get('quota');("." to run)> printf("Current Quota is: %s\n",currentQuota);("." to run)> set('quota','30G');("." to run)> run('commit');("." to run)> currentQuota=get('quota');("." to run)> printf("Current Quota is: %s\n",currentQuota);("." to run)> .Current Quota is: 0Current Quota is: 32212254720This shows us using both the get and set methods as can be used in scripts, of course when only setting an individual share, the above is overkill - it would be much easier to set it manually at the cli using 'set quota=3G' and then 'commit'.List MethodThe list method can be very powerful, especially in more complex scripts which iterate over large amounts of data and manipulate it if so desired. The general way you will use list is as follows:var myVar=list();Which will make "myVar" an array, containing all the objects in the relevant context (this could be a list of users, shares, projects, etc). You can then gather or manipulate data very easily.We could list all the shares and mountpoints in a given project for example:fishy10:shares another-project> script("." to run)> var shares=list();("." to run)> for (i=0; i < shares.length; i++)("." to run)> {("." to run)>    run('select ' + shares[i]);("." to run)>    var mountpoint=get('mountpoint');("." to run)>    printf("Share %s discovered, has mountpoint %s\n",shares[i],mountpoint);("." to run)>    run('done');("." to run)> }("." to run)> .Share and-another discovered, has mountpoint /export/another-project/and-anotherShare another-share discovered, has mountpoint /export/another-project/another-shareShare bob discovered, has mountpoint /export/another-projectShare more-shares-for-all discovered, has mountpoint /export/another-project/more-shares-for-allShare yep discovered, has mountpoint /export/another-project/yepWriting More Complex and Re-Usable CodeFunctionsThe best way to be able to write more complex code is to use functions to split up repeatable or reusable sections of your code. This also makes your more complex code easier to read and understand for other programmers.We write functions as follows:function functionName(variable1,variable2,...,variableN){}For example, we could have a function that takes a project name as input, and lists shares for that project (assuming we're already in the 'project' context - context is important!):function getShares(proj){        run('select ' + proj);        shares=list();        printf("Project: %s\n", proj);        for(j=0; j < shares.length; j++)        {                printf("Discovered share: %s\n",shares[i]);        }        run('done'); // exit selected project}Commenting your CodeLike any other language, a large part of making it readable and understandable is to comment it. You can use the same comment style as in C and Java amongst other languages.In other words, sngle line comments use://at the beginning of the comment.Multi line comments use:/*at the beginning, and:*/ at the end.For example, here we will use both:fishy10:> script("." to run)> // This is a test comment("." to run)> printf("doing some work...\n");("." to run)> /* This is a multi-line("." to run)> comment which I will span across("." to run)> three lines in total */("." to run)> printf("doing some more work...\n");("." to run)> .doing some work...doing some more work...Your comments do not have to be on their own, they can begin (particularly with single line comments this is handy) at the end of a statement, for examplevar projects=list(); // The variable projects is an array containing all projects on the system.Try and Catch StatementsYou may be used to using try and catch statements in other languages, and they can (and should) be utilised in your code to catch expected or unexpected error conditions, that you do NOT wish to stop your code from executing (if you do not catch these errors, your script will exit!):try{  // do some work}catch(err) // Catch any error that could occur{ // do something here under the error condition}For example, you may wish to only execute some code if a context can be reached. If you can't perform certain actions under certain circumstances, that may be perfectly acceptable.For example if you want to test a condition that only makes sense when looking at a SMB/NFS share, but does not make sense when you hit an iscsi or FC LUN, you don't want to stop all processing of other shares you may not have covered yet.For example we may wish to obtain quota information on all shares for all users on a share (but this makes no sense for a LUN):function getShareQuota(shar) // Get quota for each user of this share{        run('select ' + shar);        printf("  SHARE: %s\n", shar);        try        {                run('users');                printf("    %20s        %11s    %11s    %3s\n","Username","Usage(G)","Quota(G)","Quota(%)");                printf("    %20s        %11s    %11s    %4s\n","--------","--------","--------","----");                                users=list();                for(k=0; k < users.length; k++)                {                        user=users[k];                        getUserQuota(user);                }                run('done'); // exit user context        }        catch(err)        {                printf("    SKIPPING %s - This is NOT a NFS or CIFs share, not looking for users\n", shar);        }        run('done'); // done with this share}Running Scripts Remotely over SSHAs you have likely noticed, writing and running scripts for all but the simplest jobs directly on the appliance is not going to be a lot of fun.There's a couple of choices on what you can do here:Create scripts on a remote system and run them over sshCreate scripts, wrapping them in workflow code, so they are stored on the appliance and can be triggered under certain circumstances (like a threshold being reached)We'll cover the first one here, and then cover workflows later on (as these are for the most part just scripts with some wrapper information around them).Creating a SSH Public/Private SSH Key PairLog on to your handy Solaris box (You wouldn't be using any other OS, right? :P) and use ssh-keygen to create a pair of ssh keys. I'm storing this separate to my normal key:[geoff@lightning ~] ssh-keygen -t rsa -b 1024Generating public/private rsa key pair.Enter file in which to save the key (/export/home/geoff/.ssh/id_rsa): /export/home/geoff/.ssh/nas_key_rsaEnter passphrase (empty for no passphrase): Enter same passphrase again: Your identification has been saved in /export/home/geoff/.ssh/nas_key_rsa.Your public key has been saved in /export/home/geoff/.ssh/nas_key_rsa.pub.The key fingerprint is:7f:3d:53:f0:2a:5e:8b:2d:94:2a:55:77:66:5c:9b:14 geoff@lightningInstalling the Public Key on the ApplianceOn your Solaris host, observe the public key:[geoff@lightning ~] cat .ssh/nas_key_rsa.pub ssh-rsa AAAAB3NzaC1yc2EAAAABIwAAAIEAvYfK3RIaAYmMHBOvyhKM41NaSmcgUMC3igPN5gUKJQvSnYmjuWG6CBr1CkF5UcDji7v19jG3qAD5lAMFn+L0CxgRr8TNaAU+hA4/tpAGkjm+dKYSyJgEdMIURweyyfUFXoerweR8AWW5xlovGKEWZTAfvJX9Zqvh8oMQ5UJLUUc= geoff@lightningNow, copy and paste everything after "ssh-rsa" and before "user@hostname" - in this case, geoff@lightning. That is, this bit:AAAAB3NzaC1yc2EAAAABIwAAAIEAvYfK3RIaAYmMHBOvyhKM41NaSmcgUMC3igPN5gUKJQvSnYmjuWG6CBr1CkF5UcDji7v19jG3qAD5lAMFn+L0CxgRr8TNaAU+hA4/tpAGkjm+dKYSyJgEdMIURweyyfUFXoerweR8AWW5xlovGKEWZTAfvJX9Zqvh8oMQ5UJLUUc=Logon to your appliance and get into the preferences -> keys area for this user (root):[geoff@lightning ~] ssh [email protected]: Last login: Mon Dec  6 17:13:28 2010 from 192.168.0.2fishy10:> configuration usersfishy10:configuration users> select rootfishy10:configuration users root> preferences fishy10:configuration users root preferences> keysOR do it all in one hit:fishy10:> configuration users select root preferences keysNow, we create a new public key that will be accepted for this user and set the type to RSA:fishy10:configuration users root preferences keys> createfishy10:configuration users root preferences key (uncommitted)> set type=RSASet the key itself using the string copied previously (between ssh-rsa and user@host), and set the key ensuring you put double quotes around it (eg. set key="<key>"):fishy10:configuration users root preferences key (uncommitted)> set key="AAAAB3NzaC1yc2EAAAABIwAAAIEAvYfK3RIaAYmMHBOvyhKM41NaSmcgUMC3igPN5gUKJQvSnYmjuWG6CBr1CkF5UcDji7v19jG3qAD5lAMFn+L0CxgRr8TNaAU+hA4/tpAGkjm+dKYSyJgEdMIURweyyfUFXoerweR8AWW5xlovGKEWZTAfvJX9Zqvh8oMQ5UJLUUc="Now set the comment for this key (do not use spaces):fishy10:configuration users root preferences key (uncommitted)> set comment="LightningRSAKey" Commit the new key:fishy10:configuration users root preferences key (uncommitted)> commitVerify the key is there:fishy10:configuration users root preferences keys> lsKeys:NAME     MODIFIED              TYPE   COMMENT                                  key-000  2010-10-25 20:56:42   RSA    cycloneRSAKey                           key-001  2010-12-6 17:44:53    RSA    LightningRSAKey                         As you can see, we now have my new key, and a previous key I have created on this appliance.Running your Script over SSH from a Remote SystemHere I have created a basic test script, and saved it as test.ecma3:[geoff@lightning ~] cat test.ecma3 script// This is a test script, By Geoff Ongley 2010.printf("Testing script remotely over ssh\n");.Now, we can run this script remotely with our keyless login:[geoff@lightning ~] ssh -i .ssh/nas_key_rsa root@fishy10 < test.ecma3Pseudo-terminal will not be allocated because stdin is not a terminal.Testing script remotely over sshPutting it Together - An Example Completed Quota Gathering ScriptSo now we have a lot of the basics to creating a script, let us do something useful, like, find out how much every user is using, on every share on the system (you will recognise some of the code from my previous examples): script/************************************** Quick and Dirty Quota Check script ** Written By Geoff Ongley            ** 25 October 2010                    **************************************/function getUserQuota(usr){        run('select ' + usr);        var username=get('name');        var usage=get('usage');        var quota=get('quota');        var usage_g=usage / 1073741824; // convert bytes to gigabytes        var quota_g=quota / 1073741824; // as above        var quota_percent=0        if (quota > 0)        {                quota_percent=(usage / quota)*(100/1);        }        printf("    %20s        %8.2f           %8.2f           %d%%\n",username,usage_g,quota_g,quota_percent);        run('done'); // done with this selected user}function getShareQuota(shar){        //printf("DEBUG: selecting share %s\n", shar);        run('select ' + shar);        printf("  SHARE: %s\n", shar);        try        {                run('users');                printf("    %20s        %11s    %11s    %3s\n","Username","Usage(G)","Quota(G)","Quota(%)");                printf("    %20s        %11s    %11s    %4s\n","--------","--------","--------","--------");                                users=list();                for(k=0; k < users.length; k++)                {                        user=users[k];                        getUserQuota(user);                }                run('done'); // exit user context        }        catch(err)        {                printf("    SKIPPING %s - This is NOT a NFS or CIFs share, not looking for users\n", shar);        }        run('done'); // done with this share}function getShares(proj){        //printf("DEBUG: selecting project %s\n",proj);        run('select ' + proj);        shares=list();        printf("Project: %s\n", proj);        for(j=0; j < shares.length; j++)        {                share=shares[j];                getShareQuota(share);        }        run('done'); // exit selected project}function getProjects(){        run('cd /');        run('shares');        projects=list();                for (i=0; i < projects.length; i++)        {                var project=projects[i];                getShares(project);        }        run('done'); // exit context for all projects}getProjects();.Which can be run as follows, and will print information like this:[geoff@lightning ~/FISHWORKS_SCRIPTS] ssh -i ~/.ssh/nas_key_rsa root@fishy10 < get_quota_utilisation.ecma3Pseudo-terminal will not be allocated because stdin is not a terminal.Project: another-project  SHARE: and-another                Username           Usage(G)       Quota(G)    Quota(%)                --------           --------       --------    --------                  nobody            0.00            0.00        0%                 geoffro            0.05            0.00        0%                   Billy            0.10            0.00        0%                    root            0.00            0.00        0%            testing-user            0.05            0.00        0%  SHARE: another-share                Username           Usage(G)       Quota(G)    Quota(%)                --------           --------       --------    --------                    root            0.00            0.00        0%                  nobody            0.00            0.00        0%                 geoffro            0.05            0.49        9%            testing-user            0.05            0.02        249%                   Billy            0.10            0.29        33%  SHARE: bob                Username           Usage(G)       Quota(G)    Quota(%)                --------           --------       --------    --------                  nobody            0.00            0.00        0%                    root            0.00            0.00        0%  SHARE: more-shares-for-all                Username           Usage(G)       Quota(G)    Quota(%)                --------           --------       --------    --------                   Billy            0.10            0.00        0%            testing-user            0.05            0.00        0%                  nobody            0.00            0.00        0%                    root            0.00            0.00        0%                 geoffro            0.05            0.00        0%  SHARE: yep                Username           Usage(G)       Quota(G)    Quota(%)                --------           --------       --------    --------                    root            0.00            0.00        0%                  nobody            0.00            0.00        0%                   Billy            0.10            0.01        999%            testing-user            0.05            0.49        9%                 geoffro            0.05            0.00        0%Project: default  SHARE: Test-LUN    SKIPPING Test-LUN - This is NOT a NFS or CIFs share, not looking for users  SHARE: test-geoff                Username           Usage(G)       Quota(G)    Quota(%)                --------           --------       --------    --------                 geoffro            0.05            0.00        0%                    root            3.18           10.00        31%                    uucp            0.00            0.00        0%                  nobody            0.59            0.49        119%^CKilled by signal 2.Creating a WorkflowWorkflows are scripts that we store on the appliance, and can have the script execute either on request (even from the BUI), or on an event such as a threshold being met.Workflow BasicsA workflow allows you to create a simple process that can be executed either via the BUI interface interactively, or by an alert being raised (for some threshold being reached, for example).The basics parameters you will have to set for your "workflow object" (notice you're creating a variable, that embodies ECMAScript) are as follows (parameters is optional):name: A name for this workflowdescription: A Description for the workflowparameters: A set of input parameters (useful when you need user input to execute the workflow)execute: The code, the script itself to execute, which will be function (parameters)With parameters, you can specify things like this (slightly modified sample taken from the System Administration Guide):          ...parameters:        variableParam1:         {                             label: 'Name of Share',                             type: 'String'                  },                  variableParam2                  {                             label: 'Share Size',                             type: 'size'                  },execute: ....};  Note the commas separating the sections of name, parameters, execute, and so on. This is important!Also - there is plenty of properties you can set on the parameters for your workflow, these are described in the Sun ZFS Storage System Administration Guide.Creating a Basic Workflow from a Basic ScriptTo make a basic script into a basic workflow, you need to wrap the following around your script to create a 'workflow' object:var workflow = {name: 'Get User Quotas',description: 'Displays Quota Utilisation for each user on each share',execute: function() {// (basic script goes here, minus the "script" at the beginning, and "." at the end)}};However, it appears (at least in my experience to date) that the workflow object may only be happy with one function in the execute parameter - either that or I'm doing something wrong. As far as I can tell, after execute: you should only have a basic one function context like so:execute: function(){}To deal with this, and to give an example similar to our script earlier, I have created another simple quota check, to show the same basic functionality, but in a workflow format:var workflow = {name: 'Get User Quotas',description: 'Displays Quota Utilisation for each user on each share',execute: function () {        run('cd /');        run('shares');        projects=list();                for (i=0; i < projects.length; i++)        {                run('select ' + projects[i]);                shares=list('filesystem');                printf("Project: %s\n", projects[i]);                for(j=0; j < shares.length; j++)                {                        run('select ' +shares[j]);                        try                        {                                run('users');                                printf("  SHARE: %s\n", shares[j]);                                printf("    %20s        %11s    %11s    %3s\n","Username","Usage(G)","Quota(G)","Quota(%)");                                printf("    %20s        %11s    %11s    %4s\n","--------","--------","--------","-------");                                users=list();                                for(k=0; k < users.length; k++)                                {                                        run('select ' + users[k]);                                        username=get('name');                                        usage=get('usage');                                        quota=get('quota');                                        usage_g=usage / 1073741824; // convert bytes to gigabytes                                        quota_g=quota / 1073741824; // as above                                        quota_percent=0                                        if (quota > 0)                                        {                                                quota_percent=(usage / quota)*(100/1);                                        }                                        printf("    %20s        %8.2f   %8.2f   %d%%\n",username,usage_g,quota_g,quota_percent);                                        run('done');                                }                                run('done'); // exit user context                        }                        catch(err)                        {                        //      printf("    %s is a LUN, Not looking for users\n", shares[j]);                        }                        run('done'); // exit selected share context                }                run('done'); // exit project context        }        }};SummaryThe Sun ZFS Storage 7000 Appliance offers lots of different and interesting features to Sun/Oracle customers, including the world renowned Analytics. Hopefully the above will help you to think of new creative things you could be doing by taking advantage of one of the other neat features, the internal scripting engine!Some references are below to help you continue learning more, I'll update this post as I do the same! Enjoy...More information on ECMAScript 3A complete reference to ECMAScript 3 which will help you learn more of the details you may be interested in, can be found here:http://www.ecma-international.org/publications/files/ECMA-ST-ARCH/ECMA-262,%203rd%20edition,%20December%201999.pdfMore Information on Administering the Sun ZFS Storage 7000The Sun ZFS Storage 7000 System Administration guide can be a useful reference point, and can be found here:http://wikis.sun.com/download/attachments/186238602/2010_Q3_2_ADMIN.pdf

    Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >