Search Results

Search found 2230 results on 90 pages for 'gateway'.

Page 83/90 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

  • What else can I do to secure my Linux server?

    - by eric01
    I want to put a web application on my Linux server: I will first explain to you what the web app will do and then I will tell you what I did so far to secure my brand new Linux system. The app will be a classified ads website (like gumtree.co.uk) where users can sell their items, upload images, send to and receive emails from the admin. It will use SSL for some pages. I will need SSH. So far, what I did to secure my stock Ubuntu (latest version) is the following: NOTE: I probably did some things that will prevent the application from doing all its tasks, so please let me know of that. My machine's sole purpose will be hosting the website. (I put numbers as bullet points so you can refer to them more easily) 1) Firewall I installed Uncomplicated Firewall. Deny IN & OUT by default Rules: Allow IN & OUT: HTTP, IMAP, POP3, SMTP, SSH, UDP port 53 (DNS), UDP port 123 (SNTP), SSL, port 443 (the ones I didn't allow were FTP, NFS, Samba, VNC, CUPS) When I install MySQL & Apache, I will open up Port 3306 IN & OUT. 2) Secure the partition in /etc/fstab, I added the following line at the end: tmpfs /dev/shm tmpfs defaults,rw 0 0 Then in console: mount -o remount /dev/shm 3) Secure the kernel In the file /etc/sysctl.conf, there are a few different filters to uncomment. I didn't know which one was relevant to web app hosting. Which one should I activate? They are the following: A) Turn on Source Address Verification in all interfaces to prevent spoofing attacks B) Uncomment the next line to enable packet forwarding for IPv4 C) Uncomment the next line to enable packet forwarding for IPv6 D) Do no accept ICMP redirects (we are not a router) E) Accept ICMP redirects only for gateways listed in our default gateway list F) Do not send ICMP redirects G) Do not accept IP source route packets (we are not a router) H) Log Martian Packets 4) Configure the passwd file Replace "sh" by "false" for all accounts except user account and root. I also did it for the account called sshd. I am not sure whether it will prevent SSH connection (which I want to use) or if it's something else. 5) Configure the shadow file In the console: passwd -l to lock all accounts except user account. 6) Install rkhunter and chkrootkit 7) Install Bum Disabled those services: "High performance mail server", "unreadable (kerneloops)","unreadable (speech-dispatcher)","Restores DNS" (should this one stay on?) 8) Install Apparmor_profiles 9) Install clamav & freshclam (antivirus and update) What did I do wrong and what should I do more to secure this Linux machine? Thanks a lot in advance

    Read the article

  • how can I give openvpn clients access to a dns server (bind9) that is located on the same machine as the openvpn server

    - by lacrosse1991
    I currently have a debian server that is running an openvpn server. I also have a dns server (bind9) that I would like give allow access to by the connected openvpn clients, but I am unsure as of how to do this, I already known how to send dns options to the clients using push "dhcp-option DNS x.x.x.x" but I am just unsure how give the clients access to the dns server that is located on the same machine as the vpn server, so if anyone could point me in the right direction I would really appreciate it. Also in case this would have anything to do with adding rules to iptables, this is my current configuration for iptables # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *nat :PREROUTING ACCEPT [3831842:462225238] :INPUT ACCEPT [3820049:461550908] :OUTPUT ACCEPT [1885011:139487044] :POSTROUTING ACCEPT [1883834:139415168] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE COMMIT # Completed on Thu Oct 18 22:05:33 2012 # Generated by iptables-save v1.4.14 on Thu Oct 18 22:05:33 2012 *filter :INPUT ACCEPT [45799:10669929] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [45747:10335026] :fail2ban-apache - [0:0] :fail2ban-apache-myadmin - [0:0] :fail2ban-apache-noscript - [0:0] :fail2ban-ssh - [0:0] :fail2ban-ssh-ddos - [0:0] :fail2ban-webserver-w00tw00t - [0:0] -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-myadmin -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-webserver-w00tw00t -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache-noscript -A INPUT -p tcp -m multiport --dports 80,443 -j fail2ban-apache -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh-ddos -A INPUT -p tcp -m multiport --dports 22 -j fail2ban-ssh -A INPUT -i tun+ -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 3306 -j ACCEPT -A FORWARD -i tun+ -j ACCEPT -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT -A fail2ban-apache -j RETURN -A fail2ban-apache-myadmin -s 211.154.213.122/32 -j DROP -A fail2ban-apache-myadmin -s 201.170.229.96/32 -j DROP -A fail2ban-apache-myadmin -j RETURN -A fail2ban-apache-noscript -j RETURN -A fail2ban-ssh -s 76.9.59.66/32 -j DROP -A fail2ban-ssh -s 64.13.220.73/32 -j DROP -A fail2ban-ssh -s 203.69.139.179/32 -j DROP -A fail2ban-ssh -s 173.10.11.146/32 -j DROP -A fail2ban-ssh -j RETURN -A fail2ban-ssh-ddos -j RETURN -A fail2ban-webserver-w00tw00t -s 217.70.51.154/32 -j DROP -A fail2ban-webserver-w00tw00t -s 86.35.242.58/32 -j DROP -A fail2ban-webserver-w00tw00t -j RETURN COMMIT # Completed on Thu Oct 18 22:05:33 2012 also here is my openvpn server configuration port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt keepalive 10 120 comp-lzo user nobody group users persist-key persist-tun status /var/log/openvpn/openvpn-status.log verb 3 push "redirect-gateway def1" push "dhcp-option DNS 213.133.98.98" push "dhcp-option DNS 213.133.99.99" push "dhcp-option DNS 213.133.100.100" client-to-client

    Read the article

  • Tips for maximizing Nginx requests/sec?

    - by linkedlinked
    I'm building an analytics package, and project requirements state that I need to support 1 billion hits per day. Yep, "billion". In other words, no less than 12,000 hits per second sustained, and preferably some room to burst. I know I'll need multiple servers for this, but I'm trying to get maximum performance out of each node before "throwing more hardware at it". Right now, I have the hits-tracking portion completed, and well optimized. I pretty much just save the requests straight into Redis (for later processing with Hadoop). The application is Python/Django with a gunicorn for the gateway. My 2GB Ubuntu 10.04 Rackspace server (not a production machine) can serve about 1200 static files per second (benchmarked using Apache AB against a single static asset). To compare, if I swap out the static file link with my tracking link, I still get about 600 requests per second -- I think this means my tracker is well optimized, because it's only a factor of 2 slower than serving static assets. However, when I benchmark with millions of hits, I notice a few things -- No disk usage -- this is expected, because I've turned off all Nginx logs, and my custom code doesn't do anything but save the request details into Redis. Non-constant memory usage -- Presumably due to Redis' memory managing, my memory usage will gradually climb up and then drop back down, but it's never once been my bottleneck. System load hovers around 2-4, the system is still responsive during even my heaviest benchmarks, and I can still manually view http://mysite.com/tracking/pixel with little visible delay while my (other) server performs 600 requests per second. If I run a short test, say 50,000 hits (takes about 2m), I get a steady, reliable 600 requests per second. If I run a longer test (tried up to 3.5m so far), my r/s degrades to about 250. My questions -- a. Does it look like I'm maxing out this server yet? Is 1,200/s static files nginx performance comparable to what others have experienced? b. Are there common nginx tunings for such high-volume applications? I have worker threads set to 64, and gunicorn worker threads set to 8, but tweaking these values doesn't seem to help or harm me much. c. Are there any linux-level settings that could be limiting my incoming connections? d. What could cause my performance to degrade to 250r/s on long-running tests? Again, the memory is not maxing out during these tests, and HDD use is nil. Thanks in advance, all :)

    Read the article

  • Why is Linux choosing the wrong source ip address

    - by Scheintod
    and what to do to let it choose the right one? This all happens inside an OpenVZ container: The Host is Debian/Wheezy with Redhat/OpenVZ Kernel: root@mycl2:~# uname -a Linux mycl2 2.6.32-openvz-042stab081.5-amd64 #1 SMP Mon Sep 30 16:40:27 MSK 2013 x86_64 GNU/Linux The container has two (virtual) network interfaces. One in public and one in private address-space: root@mycl2:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:775 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:32059 (31.3 KiB) TX bytes:56309 (54.9 KiB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:80.123.123.29 P-t-P:80.123.123.29 Bcast:80.123.123.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.0.1.29 P-t-P:10.0.1.29 Bcast:10.0.1.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 The route to the private network is set manually: root@mycl2:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 venet0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 venet0 Tring to ping others on the private network leads to the wrong source address been choosen: root@mycl2:~# ip route get 10.0.1.26 10.0.1.26 dev venet0 src 80.123.123.29 cache mtu 1500 advmss 1460 hoplimit 64 Why is this and what can I do about it? EDIT: If I create the route with (thanks to Joshua) ip route add 10.0.0.0/8 dev venet0 src 10.0.1.29 it is working. But according to man ip-route the src parameter should only set the source-ip if this route is chosen. But if this route is chosen then the source-ip would be that anyway.

    Read the article

  • [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

    - by Beco
    I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

    Read the article

  • Rob Blackwell on interoperability and Azure

    - by Eric Nelson
    At QCon in March we had a sample Azure application implemented in both Java and Ruby to demonstrate that the Windows Azure Platform is not just about .NET. The following is an interesting interview with Rob Blackwell, the R&D director of the partner who implemented the application. UK Interoperability Team Interviews Rob Blackwell, R&D Director at Active Web Solutions. Is Microsoft taking interoperability seriously? Yes. In the past, I think Microsoft has, quite rightly come in for criticism, but architects and developers should look at this again. The Interoperability Bridges site (http://www.interoperabilitybridges.com/ ) shows a wide range of projects that allow interoperability from Java, Ruby and PHP for example. The Windows Azure platform has been architected with interoperable APIs in mind. It's straightforward to access the various storage facilities from just about any language or platform. Azure compute is capable of running more than just C# applications! Why is interoperability important to you? My company provides consultancy and bespoke development services. We're a Microsoft Gold Partner, but we live in the real world where companies have a mix of technologies provided by a variety of vendors. When developing an enterprise software solution, you rarely have a completely blank canvas. We often see integration scenarios where we need to exchange data with legacy systems. It's not unusual to see modern Silverlight applications being built on top of Java or Mainframe based back ends. Could you give us some examples of where interoperability has been important for your projects? We developed an innovative Sea Safety system for the RNLI Lifeboats here in the UK. Commercial Fishing is one of the most dangerous professions and we helped developed the MOB Guardian System which uses satellite technology and man overboard devices to raise the alarm when a fisherman gets into trouble. The solution is implemented in .NET running on Windows, but without interoperable standards, it would have been impossible to communicate with the satellite gateway technology. For more information, please see the case study: http://www.microsoft.com/casestudies/Case_Study_Detail.aspx?CaseStudyID=4000005892 More recently, we were asked to build a web site to accompany the QCon 2010 conference in London to help demonstrate and promote interoperability. We built the site using Java and Restlet and hosted it in Windows Azure Compute. The site accepts feedback from visitors and all the data is stored in Windows Azure Storage. We also ported the application to Ruby on Rails for demonstration purposes. Visitors to the stand were surprised that this was even possible. Why should Java developers be interested in Windows Azure? Windows Azure Storage consists of Blobs, Queues and Tables. The storage is scalable, durable, secure and cost-effective. Using the WindowsAzure4j library, it's easy to use, and takes just a few lines of code. If you are writing an application with large data storage requirements, or you want an offsite backup, it makes a lot of sense. Running Java applications in Azure Compute is straightforward with tools like the Tomcat Solution Accelerator (http://code.msdn.microsoft.com/winazuretomcat )and AzureRunMe (http://azurerunme.codeplex.com/ ). The Windows Azure AppFabric Service Bus can also be used to connect heterogeneous systems running on different networks and in different data centres. How can The Service Bus be considered an interoperability solution? I think that the Windows Azure AppFabric Service Bus is one of Microsoft’s best kept secrets. Think of it as “a globally scalable application plumbing kit in the sky”. If you have used Enterprise Service Buses before, you’ll be familiar with the concept. Applications can connect to the service bus to securely exchange data – these can be point to point or multicast links. With the AppFabric Service Bus, the applications can exist anywhere that has access to the Internet and the connections can traverse firewalls. This makes it easy to extend or scale your application or reach out to other networks and technologies. For example, let’s say you have a SQL Server database running on premises and you want to expose the data to a Java application running in the cloud. You could set up a point to point Service Bus connection and use JDBC. Traditionally this would have been difficult or impossible without punching holes in firewalls and compromising security. Rob Blackwell is R&D Director at Active Web Solutions, www.aws.net , a Microsoft Gold Partner specialising in leading edge software solutions. He is an occasional writer and conference speaker and blogs at www.robblackwell.org.uk Related Links: UK Azure Online Community – join today. UK Windows Azure Site Start working with Windows Azure

    Read the article

  • Virtual host in Apache Zend

    - by llocani
    I'd like to ask you if you can tell me why I can't get Vhost in Apache to work my Vhostconf is: NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] DocumentRoot "E:/Archivos de programa/Zend/Apache2/htdocs" ServerName localhost <Directory "E:/Archivos de programa/Zend/Apache2/htdocs"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> #AllowOveride all </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands" ServerName healinghands.loc <Directory "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands/logs/error.log" CustomLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands/logs/access.log" common #AllowOveride all </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects" ServerName dev.loc <Directory "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/logs/error.log" CustomLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/logs/access.log" common #AllowOveride all </VirtualHost> My httpd.conf is: ServerRoot "E:\Archivos de programa\Zend\Apache2" Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule filter_module modules/mod_filter.so LoadModule headers_module modules/mod_headers.so LoadModule imagemap_module modules/mod_imagemap.so LoadModule include_module modules/mod_include.so LoadModule info_module modules/mod_info.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule ssl_module modules/mod_ssl.so LoadModule status_module modules/mod_status.so LoadModule userdir_module modules/mod_userdir.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> ServerAdmin [email protected] DocumentRoot "E:\Archivos de programa\Zend\Apache2/htdocs" <Directory /> Options FollowSymLinks AllowOverride all Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.php index.html home.php </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> Alias /NetBeansProjects "E:\Documents and Settings\dvieira\Mis documentos\NetBeansProjects" ScriptAlias /cgi-bin/ "E:\Archivos de programa\Zend\Apache2/cgi-bin/" </IfModule> <IfModule cgid_module> </IfModule> <Directory "E:\Archivos de programa\Zend\Apache2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-vhosts.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> Include "conf/zend.conf" NameVirtualHost *:80 <VirtualHost *:80> Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/zend-default-vhost-80.conf" </VirtualHost> Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/globals-*.conf" Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/vhost_*.conf" And my host in Windows: 127.0.0.1 localhost 127.0.0.1 healinghands.loc 127.0.0.1 dev.loc And I can't get any of the browser to recognize dev.loc or healinghands.loc but a ping does it. Localhost is working fine. I've spent 3 days now traying to solve this for my one but I finally quit and have to ask. The error should be this Error Code 11002: host not found. Background: this error indicates that the gateway could not find an authoritative DNS server for the website you are trying to access. Date: 5/20/2013 5:51:03 PM Server: Source: DNS problem. i'd like to add this ping Haciendo ping a healinghands.loc [127.0.0.1] con 32 bytes de datos: Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Estadísticas de ping para 127.0.0.1: Paquetes: enviados = 4, recibidos = 4, perdidos = 0 (0% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms Today i've tryed something: i've add this domains into the exceptions of mi ie proxy config. This worked for healinghands.loc but not for dev.loc i really do not understand why, both config are exactly the same except for de documentroot. I will continue searching

    Read the article

  • Can't connect to Wired Network after installing 12.04

    - by ezz9
    I have installed 12.04 into a used HP Compaq DC 7100 CMT. Plugged in LAN cable into the computer and it says network disconnected. from what I understand on the things I've read, it's not getting the address right, maybe it's just a guess (hardware address 00:16:35:78:47:bb). I know the LAN cable is working I can get on the net with the old computer. (Old computer is using device MAC address; Auto eth0 00:11:11:E6:4F:FE). I have put this address into the newer HP and it shows last used (minutes ago) but no Internet sever not found. I tried the hardware address it says never. I feel and think this should be easy to fix. But I just don't know. Here is the info everyone has asked for, but they never say what I should do. sudo lshw -C network; rfkill list; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; uname -a; ifconfig; route -n *-network description: ethernet interface product; NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:40:00.0 logical name: eth0 verson: 01 serial: 00:16:35:78:47:bb size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000-fd configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 duplex=full firmware=5751-v3.29a latency=0 link=yes multicast=yes port=twi sted pair speed=100Mbit/s resources: irq:17 memory:f0400000-f040ffff auto lo iface lo inet loopback DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION= "Ubuntu 12.04 LTS" 00:00.0 host bridge [0600]: Inter Corporation 82915G/P/GV/GL/PL/910GL Memory Con troller Hub [8086:2580] (rev 04) 00.02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL inte grated Graphics Controller [8086:2582] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03) 00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #1 [8086:2658] (rev 03) 00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #2 [8086:2659] (rev 03) 00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #3 [8086:265a] (rev 03) 00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #4 [8086:265b] (rev 03) 00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB2 UHCI Controller [8086:265c] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI bridge [8086:244e] (rev d 3) 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/ FRW (ICH6 Family) AC'97 Autio conrtroller [8086:266e] (rev 03) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/RF (ICH6/ICH6R) LPC Interfa ce Bridge [8086:2640] (rev 03) 00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 fami ly) IDE Controller [8086:266f] (rev 03) 00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Con troller [8086:2651] (rev 03) 40:00.0 Ethernet controller [0200]: Broadcom Corporation NetXreme BCM5751 Gigab it Ethernet PCI Express [14e4:1677} (rev 01) Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Linux bob-desktop 3.2.0-23-generic-pae #36-Ubuntu SMP Tpr 10 22:19:09 UTC 20 12 i686 i686 i386 GNU/Linux eth0 Link encap:Ethernet HWaddr 00:16:35:78:47:bb inet6 addr: fe80::216:35ff:47bb/64 Scope:link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2517 errors:0 dropped:0 overruns:0 frame:0 TX packets:164 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164508 (164.5 KB) TX bytes: 40884 (40.0 KB) Interrupt:17 lo Link encap:Local loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3290 errors:0 dropped:0 overruns:0 frame:0 TX packets:3290 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen: 0 RX bytes:267212 (267.2 KB) TX bytes: 267212 (267.2 KB) Kernel Ip routing table Destination Gateway Genmask Flags Metric Ref Use Iface ran this sudo dhclient eth0 no reply ran this ip addr 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST ,MULTICAST ,UP ,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/enter 00:16:35:78:47:BB brd ff:ff:ff:ff:ff:ff inet 169.254.7.172/16 brd 169.254.255.255 scope link eth0:avahi inet6 fe80::216:35ff:fe78:47bb/64 scope link valid_lft forever preferred_lft forever Help please.

    Read the article

  • Certify August Updates

    - by Sadia2
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 We have added some release and platform certifications to MOS Certify. Applications : Oracle Demantra Demand Management 7.3.1.5, Oracle Demantra Predictive Trade Planning 7.3.1.5, Oracle Demantra Sales and Operations Planning 7.3.1.5 Database: Oracle Database Client 12.1.0.1.0 11.2.0.4.0, Oracle Clusterware 11.2.0.4.0, Oracle Database 11.2.0.4.0, Oracle Real Application Clusters 11.2.0.4.0 E-Business Suite: Oracle E-Business Suite 12.1.3, Oracle E-Business Suite 12.1.2, Oracle E-Business Suite 12.1.1, Oracle E-Business Suite 12.0.6, Oracle E-Business Suite 11.5.10.2 Edge Applications: Oracle Transportation Management 6.3.2 Enterprise Manager: Oracle Application Management Pack for Oracle E-Business Suite 12.1.0.1.0 Fusion Middleware: Discoverer Administrator 11.1.1.6.0, Discoverer Desktop 11.1.1.6.0, Forms Builder 11.1.1.6.0, Oracle Application Development Framework 11.1.1.6.0, Oracle Application Development Runtime 11.1.1.6.0, Oracle Business Intelligence Publisher 11.1.1.6.0, Oracle Directory Services Manager 11.1.1.6.0, Oracle Forms 11.1.1.6.0, Oracle GoldenGate 11.1.1.1.0, 11.1.1.1.2, 11.1.1.1.1, Oracle GoldenGate Application Adapters 11.1.1.1.1, Oracle Identity and Access Management 11.1.2.0.0, 11.1.2.1.0, Oracle Identity Federation 11.1.1.6.0, Oracle Real-Time Decision Load Generator 11.1.1.7.0, Oracle Real-Time Decision Studio 11.1.1.7.0, Oracle Real-Time Decisions 11.1.1.6.0, Oracle Reports 11.1.1.6.0, Oracle Segmentation Server 11.1.1.6.0, Oracle Virtual Directory 11.1.1.6.0, Oracle Web Cache 11.1.1.6.0, Oracle WebCenter Content Imaging 11.1.1.8.0, Oracle WebCenter Content Inbound Refinery Server 11.1.1.8.0, Oracle WebCenter Content Records 11.1.1.8.0, Oracle WebCenter Content Rights 11.1.1.8.0, Oracle WebCenter Content UI 11.1.1.8.0, Oracle WebCenter Enterprise Capture 11.1.1.8.0, Oracle WebCenter Portal 11.1.1.8.0, Oracle WebCenter Sites 11.1.1.8.0, Oracle WebCenter Sites: CIP for EMC Documentum 11.1.1.8.0, Oracle WebCenter Sites: CIP for File Systems and MS SharePoint 11.1.1.8.0, Oracle WebCenter Sites: Community-Gadgets 11.1.1.8.0, Oracle WebCenter Sites: Explorer 11.1.1.8.0, Oracle WebCenter Universal Content Management 11.1.1.8.0, Reports Builder 11.1.1.6.0, Oracle WebCenter Content Records 11.1.1.8.0, Oracle WebCenter Content Rights 11.1.1.8.0, Oracle WebCenter Content UI 11.1.1.8.0, Oracle WebCenter Sites: Developer Tools 11.1.1.8.0 FSGBU Insurance Group : Oracle Health Insurance Claims 2.13.3.0.0, 2.13.2.0.0, 2.13.1.0.0 JD Edwards EnterpriseOne: JD Edwards EnterpriseOne Tools 9.1.3.0, 9.1.2.0, 9.1.0.0 JD Edwards World: JD Edwards World Service Enablement A93SE, A931SE PeopleSoft: PeopleSoft PeopleTools 8.52 Siebel Enterprise: Siebel Application Server 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0, Siebel CRM Desktop Client 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0, Siebel Database Server 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0, Siebel HI Web Client 8.2.2.2.0, 8.1.1.9.0, Siebel Gateway Server 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0, Siebel Outlook Add-in Client 8.2.2.2.0, Siebel Remote Client 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0, Siebel Tools Client 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0, Siebel Web Server Extension 8.2.2.4.0, 8.2.2.3.0, 8.2.2.2.0, 8.1.1.11.0, 8.1.1.10.0, 8.1.1.9.0 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;}

    Read the article

  • Community Branching

    - by Dane Morgridge
    As some may have noticed, I have taken a liking to Ruby (and Rails in particular) quite a bit recently. This last weekend I spoke at the NYC Code Camp on a comparison of ASP.NET and Rails as well as an intro to Entity Framework talk.  I am speaking at RubyNation in April and have submitted to other ruby conferences around the area and I am also doing a Rails and MongoDB talk at the Philly Code Camp in April. Before you start to think this is my "I'm leaving .NET post", which it isn't so I need to clarify. I am not, nor do I intend to any time in the near future plan on abandoning .NET.  I am simply branching out into another community based on a development technology that I very much enjoy.  If you look at my twitter bio, you will see that I am into Entity Framework, Ruby on Rails, C++ and ASP.NET MVC, and not necessarily in that order.  I know you're probably thinking to your self that I am crazy, which is probably true on several levels (especially the C++ part). I was actually crazy enough at the NYC Code Camp to show up wearing a Linux t-shirt, presenting with my MacBook Pro on Entity Framework, ASP.NET MVC and Rails. (I did get pelted in the head with candy by Rachel Appel for it though) At all of the code camps I am submitting to this year, i will be submitting sessions on likely all four topics, and some sessions will be a combination of 2 or more.  For example, my "ASP.NET MVC: A Gateway To Rails?" talk touches ASP.NET MVC, Entity Framework Code First and Rails. Simply put (and I talk about this in my MVC & Rails talk) is that learning and using Rails has made me a better ASP.NET MVC developer. Just one example of this is helper methods.  When I started working with ASP.NET MVC, I didn't really want to use helpers and preferred to just use standard html tags, especially where links were concerned.  It was just me being stubborn and not really seeing all of the benefit of the helpers.  To my defense, coming from WebForms, I wanted to be as bare metal as possible and it seemed at first like a lot of the helpers were an unnecessary abstraction. I took my first look at Rails back in v1 and didn't spend very much time with it so I dismissed it and went on my merry ASP.NET WebForms way.  Then I picked up ASP.NET MVC and grasped the MVC pattern itself much better. After this, I took another look at Rails and everything made sense.  I decided then to learn Rails. (I think it is important for developers to learn new languages and platforms regularly so it was a natural progression for me) I wanted to learn it the right way, so when I dug into code, everyone used helpers everywhere for pretty much everything possible. I took some time to dig in and found out how helpful they were and subsequently realized how awesome they were in ASP.NET MVC also and started using them. In short, I love Rails (and Ruby in general).  I also love ASP.NET MVC and Entity Framework and yes I still love C++.  I have varying degrees of love for them individually at any given moment and it is likely to shift based on the current project I am working on.  I know you're thinking it so before you ask the question. "Which do I use when?", I'm going to give the standard developer answer of: It depends.  There are a lot of factors that I am not going to even go into that would go into a decision.  The most basic question I would ask though is,  does this project depend on .NET?  If it does, then I'd say that ASP.NET MVC is probably going to be the more logical choice and I am going to leave it at that.  I am working on projects right now in both technologies and I don't see that changing anytime soon (one project even uses both). With all that being said, you'll find me at code camps, conferences and user groups presenting on .NET, Ruby or both, writing about .NET and Ruby and I will likely be blogging on both in the future.  I know of others that have successfully branched out to other communities and with any luck I'll be successful at it too. On a (sorta) side note, I read a post by Justin Etheredge the other day that pretty much sums up my feelings about Ruby as a language.  I highly recommend checking it out: What Is So Great About Ruby?

    Read the article

  • WIF, ADFS 2 and WCF&ndash;Part 5: Service Client (more Flexibility with WSTrustChannelFactory)

    - by Your DisplayName here!
    See the previous posts first. WIF includes an API to manually request tokens from a token service. This gives you more control over the request and more flexibility since you can use your own token caching scheme instead of being bound to the channel object lifetime. The API is straightforward. You first request a token from the STS and then use that token to create a channel to the relying party service. I’d recommend using the WS-Trust bindings that ship with WIF to talk to ADFS 2 – they are pre-configured to match the binding configuration of the ADFS 2 endpoints. The following code requests a token for a WCF service from ADFS 2: private static SecurityToken GetToken() {     // Windows authentication over transport security     var factory = new WSTrustChannelFactory(         new WindowsWSTrustBinding(SecurityMode.Transport),         stsEndpoint);     factory.TrustVersion = TrustVersion.WSTrust13;       var rst = new RequestSecurityToken     {         RequestType = RequestTypes.Issue,         AppliesTo = new EndpointAddress(svcEndpoint),         KeyType = KeyTypes.Symmetric     };       var channel = factory.CreateChannel();     return channel.Issue(rst); } Afterwards, the returned token can be used to create a channel to the service. Again WIF has some helper methods here that make this very easy: private static void CallService(SecurityToken token) {     // create binding and turn off sessions     var binding = new WS2007FederationHttpBinding(         WSFederationHttpSecurityMode.TransportWithMessageCredential);     binding.Security.Message.EstablishSecurityContext = false;       // create factory and enable WIF plumbing     var factory = new ChannelFactory<IService>(binding, new EndpointAddress(svcEndpoint));     factory.ConfigureChannelFactory<IService>();       // turn off CardSpace - we already have the token     factory.Credentials.SupportInteractive = false;       var channel = factory.CreateChannelWithIssuedToken<IService>(token);       channel.GetClaims().ForEach(c =>         Console.WriteLine("{0}\n {1}\n  {2} ({3})\n",             c.ClaimType,             c.Value,             c.Issuer,             c.OriginalIssuer)); } Why is this approach more flexible? Well – some don’t like the configuration voodoo. That’s a valid reason for using the manual approach. You also get more control over the token request itself since you have full control over the RST message that gets send to the STS. One common parameter that you may want to set yourself is the appliesTo value. When you use the automatic token support in the WCF federation binding, the appliesTo is always the physical service address. This means in turn that this address will be used as the audience URI value in the SAML token. Well – this in turn means that when you have an application that consists of multiple services, you always have to configure all physical endpoint URLs in ADFS 2 and in the WIF configuration of the service(s). Having control over the appliesTo allows you to use more symbolic realm names, e.g. the base address or a completely logical name. Since the URL is never de-referenced you have some degree of freedom here. In the next post we will look at the necessary code to request multiple tokens in a call chain. This is a common scenario when you first have to acquire a token from an identity provider and have to send that on to a federation gateway or Resource STS. Stay tuned.

    Read the article

  • What Keeps You from Changing Your Public IP Address and Wreaking Havoc on the Internet?

    - by Jason Fitzpatrick
    What exactly is preventing you (or anyone else) from changing their IP address and causing all sorts of headaches for ISPs and other Internet users? Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. The Question SuperUser reader Whitemage is curious about what’s preventing him from wantonly changing his IP address and causing trouble: An interesting question was asked of me and I did not know what to answer. So I’ll ask here. Let’s say I subscribed to an ISP and I’m using cable internet access. The ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let’s say, 60.61.62.75, and messing with another consumer’s internet access? For the sake of this argument, let’s say that this other IP address is also owned by the same ISP. Also, let’s assume that it’s possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gateway, a network address and a broadcast address. So that’s 3 addresses the ISP “loses” to you. That seems very wasteful for dynamically assigned IP addresses, which the majority of customers are. Could they simply be using static arps? ACLs? Other simple mechanisms? Two things to investigate here, why can’t we just go around changing our addresses, and is the assignment process as wasteful as it seems? The Answer SuperUser contributor Moses offers some insight: Cable modems aren’t like your home router (ie. they don’t have a web interface with simple point-and-click buttons that any kid can “hack” into). Cable modems are “looked up” and located by their MAC address by the ISP, and are typically accessed by technicians using proprietary software that only they have access to, that only runs on their servers, and therefore can’t really be stolen. Cable modems also authenticate and cross-check settings with the ISPs servers. The server has to tell the modem whether it’s settings (and location on the cable network) are valid, and simply sets it to what the ISP has it set it for (bandwidth, DHCP allocations, etc). For instance, when you tell your ISP “I would like a static IP, please.”, they allocate one to the modem through their servers, and the modem allows you to use that IP. Same with bandwidth changes, for instance. To do what you are suggesting, you would likely have to break into the servers at the ISP and change what it has set up for your modem. Could they simply be using static arps? ACLs? Other simple mechanisms? Every ISP is different, both in practice and how close they are with the larger network that is providing service to them. Depending on those factors, they could be using a combination of ACL and static ARP. It also depends on the technology in the cable network itself. The ISP I worked for used some form of ACL, but that knowledge was a little beyond my paygrade. I only got to work with the technician’s interface and do routine maintenance and service changes. What keeps me from changing this IP address to, let’s say, 60.61.62.75 and mess with another consumer’s internet access? Given the above, what keeps you from changing your IP to one that your ISP hasn’t specifically given to you is a server that is instructing your modem what it can and can’t do. Even if you somehow broke into the modem, if 60.61.62.75 is already allocated to another customer, then the server will simply tell your modem that it can’t have it. David Schwartz offers some additional insight with a link to a white paper for the really curious: Most modern ISPs (last 13 years or so) will not accept traffic from a customer connection with a source IP address they would not route to that customer were it the destination IP address. This is called “reverse path forwarding”. See BCP 38. Have something to add to the explanation? Sound off in the the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.     

    Read the article

  • JPRT: A Build & Test System

    - by kto
    DRAFT A while back I did a little blogging on a system called JPRT, the hardware used and a summary on my java.net weblog. This is an update on the JPRT system. JPRT ("JDK Putback Reliablity Testing", but ignore what the letters stand for, I change what they mean every day, just to annoy people :\^) is a build and test system for the JDK, or any source base that has been configured for JPRT. As I mentioned in the above blog, JPRT is a major modification to a system called PRT that the HotSpot VM development team has been using for many years, very successfully I might add. Keeping the source base always buildable and reliable is the first step in the 12 steps of dealing with your product quality... or was the 12 steps from Alcoholics Anonymous... oh well, anyway, it's the first of many steps. ;\^) Internally when we make changes to any part of the JDK, there are certain procedures we are required to perform prior to any putback or commit of the changes. The procedures often vary from team to team, depending on many factors, such as whether native code is changed, or if the change could impact other areas of the JDK. But a common requirement is a verification that the source base with the changes (and merged with the very latest source base) will build on many of not all 8 platforms, and a full 'from scratch' build, not an incremental build, which can hide full build problems. The testing needed varies, depending on what has been changed. Anyone that was worked on a project where multiple engineers or groups are submitting changes to a shared source base knows how disruptive a 'bad commit' can be on everyone. How many times have you heard: "So And So made a bunch of changes and now I can't build!". But multiply the number of platforms by 8, and make all the platforms old and antiquated OS versions with bizarre system setup requirements and you have a pretty complicated situation (see http://download.java.net/jdk6/docs/build/README-builds.html). We don't tolerate bad commits, but our enforcement is somewhat lacking, usually it's an 'after the fact' correction. Luckily the Source Code Management system we use (another antique called TeamWare) allows for a tree of repositories and 'bad commits' are usually isolated to a small team. Punishment to date has been pretty drastic, the Queen of Hearts in 'Alice in Wonderland' said 'Off With Their Heads', well trust me, you don't want to be the engineer doing a 'bad commit' to the JDK. With JPRT, hopefully this will become a thing of the past, not that we have had many 'bad commits' to the master source base, in general the teams doing the integrations know how important their jobs are and they rarely make 'bad commits'. So for these JDK integrators, maybe what JPRT does is keep them from chewing their finger nails at night. ;\^) Over the years each of the teams have accumulated sets of machines they use for building, or they use some of the shared machines available to all of us. But the hunt for build machines is just part of the job, or has been. And although the issues with consistency of the build machines hasn't been a horrible problem, often you never know if the Solaris build machine you are using has all the right patches, or if the Linux machine has the right service pack, or if the Windows machine has it's latest updates. Hopefully the JPRT system can solve this problem. When we ship the binary JDK bits, it is SO very important that the build machines are correct, and we know how difficult it is to get them setup. Sure, if you need to debug a JDK problem that only shows up on Windows XP or Solaris 9, you'll still need to hunt down a machine, but not as a regular everyday occurance. I'm a big fan of a regular nightly build and test system, constantly verifying that a source base builds and tests out. There are many examples of automated build/tests, some that trigger on any change to the source base, some that just run every night. Some provide a protection gateway to the 'golden' source base which only gets changes that the nightly process has verified are good. The JPRT (and PRT) system is meant to guard the source base before anything is sent to it, guarding all source bases from the evil developer, well maybe 'evil' isn't the right word, I haven't met many 'evil' developers, more like 'error prone' developers. ;\^) Humm, come to think about it, I may be one from time to time. :\^{ But the point is that by spreading the build up over a set of machines, and getting the turnaround down to under an hour, it becomes realistic to completely build on all platforms and test it, on every putback. We have the technology, we can build and rebuild and rebuild, and it will be better than it was before, ha ha... Anybody remember the Six Million Dollar Man? Man, I gotta get out more often.. Anyway, now the nightly build and test can become a 'fetch the latest JPRT build bits' and start extensive testing (the testing not done by JPRT, or the platforms not tested by JPRT). Is it Open Source? No, not yet. Would you like to be? Let me know. Or is it more important that you have the ability to use such a system for JDK changes? So enough blabbering on about this JPRT system, tell me what you think. And let me know if you want to hear more about it or not. Stay tuned for the next episode, same Bloody Bat time, same Bloody Bat channel. ;\^) -kto

    Read the article

  • UK OUG Conference Highlights and Insights

    - by Richard Bingham
    As per my preemptive post, this was the first time the annual conference organized by the UK Oracle User Group (UKOUG) was split into two events, one for Oracle Applications and another in December for Oracle Technology. Apps13, as it was branded, was hailed as a success, with over 1000 registered attendees and three days of sessions, exhibition, round-tables and many other types of content. As this poster on their stand illustrates, the UKOUG is a strong community with popular participants from both big and small Oracle partners and customers. The venue was a more intimate setting than previous years also, allowing everyone to casually bump into those they hoped to. It gave a real feeling of an Apps Community. The main themes over the days where CRM and Customer Experience, HCM, and FIN/SCM. This allowed people to attend just one focused day if they wanted. In addition the Apps Transformation stream ran across all three days, offering insights, advice, and details on the newer product solutions like Fusion Applications.  Here are some of the key take-aways I got from the conference, specific to my role in Fusion Applications Developer Relations: User Experience continues to be a significant reason for adopting some of the newer application products available, with immediately obvious gains in user productivity and satisfaction reported by customers. Also this doesn't stop with the baked-in UX either, with their Design Patterns proving popular and indeed currently being extended to including things like extending on ADF mobile and customizing the Simplified UI. More on this to come from us soon. The executive sessions emphasized the "it's a journey" phrase, illustrating that modern business applications are powered by technologies such as Cloud, Mobile, Social and Big Data and these can be harnessed to help propel your organization forward. Indeed the emphasis is away from the traditional vendor prescribed linear applications road map, and towards plotting a course based on business priorities supported by a broad range of integrated solutions. To help with this several conference sessions demoed the new "Applications Navigator" tool, developed in partnership with OUG members, which offers a visual framework to help organizations plan their Oracle Applications investments around business and technology imperatives. Initial reaction was positive, especially as customers do not need to decipher Oracle's huge product catalog and embeds the best blend of proven and integrated applications solutions. We'll share more on this when it is generally available. Several sessions focused around explanations and interpretation of Oracle OpenWorld 2013, helping highlight the key Oracle Applications messages and directions. With a relative small percentage of conference attendees also at OpenWorld (from a show of hands) this was a popular way to distill the information available down into specific items of interest for the community. Please note the original OpenWorld 2013 content is still available for download but will not remain available forever (via the Oracle website OpenWorld Content Catalog > pick a session > see the PDF download). With the release of E-Business Suite 12.2 the move to develop and deploy on the Fusion Middleware stack becomes a reality for many Oracle Applications customers. This coupled with recent E-Business Suite features such as the Integrated SOA Gateway and the E-Business Suite SDK for Java, illustrates how the gap between the technologies and techniques involved in extending E-Business Suite and Fusion Applications is quickly narrowing. We'll see this merging continue to evolve going forwards. Getting started with Oracle Cloud Applications is actually easier than many customers expected, with a broad selection of both large and medium sized organizations explaining how they added new features to their existing Oracle Applications portfolios. New functionality available from Fusion HCM and CX are popular extensions that do not have to disrupt those core business services. Coexistence is the buzzword here, and the available integration is also simpler than many expected, commonly involving an initial setup data load, then regularly incremental synchronizations, often without a need for real-time constant communication between systems. With much of this pre-built already the implementation process is also quite rapid. With most people dressed in suits, we wanted to get the conversations going without the traditional english reserve, so we decided to make ourselves a bit more obvious, as the photo below shows. This seemed to be quite successful and helped those interested identify and approach us. Keep a look out for similar again. In fact if you're in the UK there is an "Apps Transformation Day" planned by the UKOUG for the 19th March 2014, with more details to follow. Again something we'll be sure to participate in. I am hoping to attend the next half of the UKOUG annual conference, Tech13, that focuses more on Oracle technology and where there is more likely to be larger attendance of those interested in the lower-level aspects of applications customization and development. If you're going, let me know and maybe we can meet up.

    Read the article

  • Navigation in a #WP7 application with MVVM Light

    - by Laurent Bugnion
    In MVVM applications, it can be a bit of a challenge to send instructions to the view (for example a page) from a viewmodel. Thankfully, we have good tools at our disposal to help with that. In his excellent series “MVVM Light Toolkit soup to nuts”, Jesse Liberty proposes one approach using the MVVM Light messaging infrastructure. While this works fine, I would like to show here another approach using what I call a “view service”, i.e. an abstracted service that is invoked from the viewmodel, and implemented on the view. Multiple kinds of view services In fact, I use view services quite often, and even started standardizing them for the Windows Phone 7 applications I work on. If there is interest, I will be happy to show other such view services, for example Animation services, responsible to start/stop animations on the view. Dialog service, in charge of displaying messages to the user and gathering feedback. Navigation service, in charge of navigating to a given page directly from the viewmodel. In this article, I will concentrate on the navigation service. The INavigationService interface In most WP7 apps, the navigation service is used in quite a straightforward way. We want to: Navigate to a given URI. Go back. Be notified when a navigation is taking place, and be able to cancel. The INavigationService interface is quite simple indeed: public interface INavigationService { event NavigatingCancelEventHandler Navigating; void NavigateTo(Uri pageUri); void GoBack(); } Obviously, this interface can be extended if necessary, but in most of the apps I worked on, I found that this covers my needs. The NavigationService class It is possible to nicely pack the navigation service into its own class. To do this, we need to remember that all the PhoneApplicationPage instances use the same instance of the navigation service, exposed through their NavigationService property. In fact, in a WP7 application, it is the main frame (RootFrame, of type PhoneApplicationFrame) that is responsible for this task. So, our implementation of the NavigationService class can leverage this. First the class will grab the PhoneApplicationFrame and store a reference to it. Also, it registers a handler for the Navigating event, and forwards the event to the listening viewmodels (if any). Then, the NavigateTo and the GoBack methods are implemented. They are quite simple, because they are in fact just a gateway to the PhoneApplicationFrame. The whole class is as follows: public class NavigationService : INavigationService { private PhoneApplicationFrame _mainFrame; public event NavigatingCancelEventHandler Navigating; public void NavigateTo(Uri pageUri) { if (EnsureMainFrame()) { _mainFrame.Navigate(pageUri); } } public void GoBack() { if (EnsureMainFrame() && _mainFrame.CanGoBack) { _mainFrame.GoBack(); } } private bool EnsureMainFrame() { if (_mainFrame != null) { return true; } _mainFrame = Application.Current.RootVisual as PhoneApplicationFrame; if (_mainFrame != null) { // Could be null if the app runs inside a design tool _mainFrame.Navigating += (s, e) => { if (Navigating != null) { Navigating(s, e); } }; return true; } return false; } } Exposing URIs I find that it is a good practice to expose each page’s URI as a constant. In MVVM Light applications, a good place to do that is the ViewModelLocator, which already acts like a central point of setup for the views and their viewmodels. Note that in some cases, it is necessary to expose the URL as a string, for instance when a query string needs to be passed to the view. So for example we could have: public static readonly Uri MainPageUri = new Uri("/MainPage.xaml", UriKind.Relative); public const string AnotherPageUrl = "/AnotherPage.xaml?param1={0}&param2={1}"; Creating and using the NavigationService Normally, we only need one instance of the NavigationService class. In cases where you use an IOC container, it is easy to simply register a singleton instance. For example, I am using a modified version of a super simple IOC container, and so I can register the navigation service as follows: SimpleIoc.Register<INavigationService, NavigationService>(); Then, it can be resolved where needed with: SimpleIoc.Resolve<INavigationService>(); Or (more frequently), I simply declare a parameter on the viewmodel constructor of type INavigationService and let the IOC container do its magic and inject the instance of the NavigationService when the viewmodel is created. On supported platforms (for example Silverlight 4), it is also possible to use MEF. Or, of course, we can simply instantiate the NavigationService in the ViewModelLocator, and pass this instance as a parameter of the viewmodels’ constructor, injected as a property, etc… Once the instance has been passed to the viewmodel, it can be used, for example with: NavigationService.NavigateTo(ViewModelLocator.ComparisonPageUri); Testing Thanks to the INavigationService interface, navigation can be mocked and tested when the viewmodel is put under unit test. Simply implement and inject a mock class, and assert that the methods are called as they should by the viewmodel. Conclusion As usual, there are multiple ways to code a solution answering your needs. I find that view services are a really neat way to delegate view-specific responsibilities such as animation, dialogs and of course navigation to other classes through an abstracted interface. In some cases, such as the NavigationService class exposed here, it is even possible to standardize the implementation and pack it in a class library for reuse. I hope that this sample is useful! Happy coding. Laurent   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

    Read the article

  • Revisiting .NET, but what should I focus on?

    - by Wayne M
    After about a two-year hiatus, I'm brushing up on my .NET skills to find a .NET job (my previous two positions have very little development, or development using legacy technologies, so apart from a few very minor apps I have not touched .NET in close to two years). I'm aware of things like ASP.NET MVC, and I have previously read on things like NHibernate and DI/IOC, albeit I have yet to use them apart from very trivial "Hello World" type applications. I have a subscription to Rob Conery's Tekpub website and occasionally watch these videos when I have free time. My concern is this: I don't live in a very technical area. I would be surprised if any but the most tech-savvy companies have heard of, let alone use, ASP.NET MVC, NHibernate (or even LINQ/EF), or know about IoC. I would be willing to bet a large sum of money that 95% of the possible jobs I could obtain will use the following: Visual Source Safe, if any VCS at all ASP.NET 2.0 Webforms (3.5 if lucky) Raw ADO.NET on top of a very thin implementation of the Gateway pattern Stored Procedures in the database for most CRUD operations Gratuitous use of code-behind, with a Service layer if I'm lucky If I were extremely lucky, I might find a shop that has heard of ORMs and either uses one, or has wrote their own data abstraction. Also if I were lucky, the company would be using Model-View-Presenter. In light of this I'm not sure what I should focus on learning. Personally, I would prefer to be using the latest stuff - ASP.NET MVC, NHibernate, jQuery, WCF etc. Reality says I should go back to the basics, since it looks like most potential opportunities aren't going to be anywhere near the cutting edge, or anywhere close to it. And, as much as I would like to find a position and start to show the other developers the benefits, in my past experience this has usually resulted in my being fired for "not being a team player" and doing things the bad old way. So, I am curious how you would approach a situation like this? What should I focus on, in order to A) Reaquaint myself with .NET, and B) Prepare myself to obtain a .NET job again that is more than likely going to use techniques that I and most other knowledgeable developers will scoff at?

    Read the article

  • Flash -> ByteArray -> AMFPHP -> Invalid Image !??

    - by undefined
    Hi, Im loading images into Flash and using JPGEncoder to encode the image to a ByteArray and send this to AMF PHP which writes out the bytearray to a file. This all appears to work correctly and I can download the resulting file in Photoshop CS4 absolutely fine. When i try to open it from the desktop or open it back in Flash it doesnt work... Picasa my default image browser says "Invalid" Here is the code i use to write the bytearray to a file - $jpg = $GLOBALS["HTTP_RAW_POST_DATA"]; file_put_contents($filename, $jpg); That's it ... I use the NetConnection class to connect and call the service, do I need to say Im sending jpg data? I assumed that JPGEncoder took care of that. How can I validate the bytearray before writing the file? Do I need to set MIME type or something .. excuse the slightly noob questions, a little knowledge can be a dangerous thing. Thanks --------------------------------------- PART II ------------------------------------------ Here is some code - 1) load the image into Flash player item.load(); function _onImageDataLoaded(evt:Event):void { var tmpFileRef:FileReference=FileReference(evt.target); image_loader=new Loader ; image_loader.contentLoaderInfo.addEventListener(Event.COMPLETE, _onImageLoaded); image_loader.loadBytes(tmpFileRef.data); } function _onImageLoaded(evt:Event):void { bitmap=Bitmap(evt.target.content); bitmap.smoothing=true; if (bitmap.width>MAX_WIDTH||bitmap.height>MAX_HEIGHT) { resizeBitmap(bitmap); } uploadResizedImage(bitmap); } function resizeBitmap(target:Bitmap):void { if (target.height>target.width) { target.width=MAX_WIDTH; target.scaleY=target.scaleX; } else if (target.width >= target.height) { target.height=MAX_HEIGHT; target.scaleX=target.scaleY; } } function uploadResizedImage(target:Bitmap):void { var _bmd:BitmapData=new BitmapData(target.width,target.height); _bmd.draw(target, new Matrix(target.scaleX, 0, 0, target.scaleY)); var encoded_jpg:JPGEncoder=new JPGEncoder(90); var jpg_binary:ByteArray=encoded_jpg.encode(_bmd); _uploadService=new NetConnection(); _uploadService.objectEncoding=ObjectEncoding.AMF3 _uploadService.connect("http://.../amfphp/gateway.php"); _uploadService.call("UploadService.receiveByteArray",new Responder(success, error), jpg_binary, currentImageFilename); } Many thanks for you help

    Read the article

  • LSP packet modify

    - by kellogs
    Hello, anybody care to share some insights on how to use LSP for packet modifying ? I am using the non IFS subtype and I can see how (pseudo?) packets first enter WSPRecv. But how do I modify them ? My inquiry is about one single HTTP response that causes WSPRecv to be called 3 times :((. I need to modify several parts of this response, but since it comes in 3 slices, it is pretty hard to modify it accordingly. And, maybe on other machines or under different conditions (such as high traffic) there would only be one sole WSPRecv call, or maybe 10 calls. What is the best way to work arround this (please no NDIS :D), and how to properly change the buffer (lpBuffers-buf) by increasing it ? int WSPAPI WSPRecv( SOCKET s, LPWSABUF lpBuffers, DWORD dwBufferCount, LPDWORD lpNumberOfBytesRecvd, LPDWORD lpFlags, LPWSAOVERLAPPED lpOverlapped, LPWSAOVERLAPPED_COMPLETION_ROUTINE lpCompletionRoutine, LPWSATHREADID lpThreadId, LPINT lpErrno ) { LPWSAOVERLAPPEDPLUS ProviderOverlapped = NULL; SOCK_INFO *SocketContext = NULL; int ret = SOCKET_ERROR; *lpErrno = NO_ERROR; // // Find our provider socket corresponding to this one // SocketContext = FindAndRefSocketContext(s, lpErrno); if ( NULL == SocketContext ) { dbgprint( "WSPRecv: FindAndRefSocketContext failed!" ); goto cleanup; } // // Check for overlapped I/O // if ( NULL != lpOverlapped ) { /*bla bla .. not interesting in my case*/ } else { ASSERT( SocketContext->Provider->NextProcTable.lpWSPRecv ); SetBlockingProvider(SocketContext->Provider); ret = SocketContext->Provider->NextProcTable.lpWSPRecv( SocketContext->ProviderSocket, lpBuffers, dwBufferCount, lpNumberOfBytesRecvd, lpFlags, lpOverlapped, lpCompletionRoutine, lpThreadId, lpErrno); SetBlockingProvider(NULL); //is this the place to modify packet length and contents ? if (strstr(lpBuffers->buf, "var mapObj = null;")) { int nLen = strlen(lpBuffers->buf) + 200; /*CHAR *szNewBuf = new CHAR[]; CHAR *pIndex; pIndex = strstr(lpBuffers->buf, "var mapObj = null;"); nLen = strlen(strncpy(szNewBuf, lpBuffers->buf, (pIndex - lpBuffers->buf) * sizeof (CHAR))); nLen = strlen(strncpy(szNewBuf + nLen * sizeof(CHAR), "var com = null;\r\n", 17 * sizeof(CHAR))); pIndex += 18 * sizeof(CHAR); nLen = strlen(strncpy(szNewBuf + nLen * sizeof(CHAR), pIndex, 1330 * sizeof (CHAR))); nLen = strlen(strncpy(szNewBuf + nLen * sizeof(CHAR), "if (com == null)\r\n" \ "com = new ActiveXObject(\"InterCommJS.Gateway\");\r\n" \ "com.lat = latitude;\r\n" \ "com.lon = longitude;\r\n}", 111 * sizeof (CHAR))); pIndex = strstr(szNewBuf, "Content-Length:"); pIndex += 16 * sizeof(CHAR); strncpy(pIndex, "1465", 4 * sizeof(CHAR)); lpBuffers->buf = szNewBuf; lpBuffers->len += 128;*/ } if ( SOCKET_ERROR != ret ) { SocketContext->BytesRecv += *lpNumberOfBytesRecvd; } } cleanup: if ( NULL != SocketContext ) DerefSocketContext( SocketContext, lpErrno ); return ret; } Thank you

    Read the article

  • Apple Push Notifications With Foreign Accent Characters Not Receiving

    - by confeng
    I'm sending push notifications and when the message contains foreign characters (Turkish in my case) like I, s, ç, g... The message does not arrive to devices. Here's my code: $message = 'THIS is push'; $passphrase = 'mypass'; $ctx = stream_context_create(); stream_context_set_option($ctx, 'ssl', 'local_cert', 'MyPemFile.pem'); stream_context_set_option($ctx, 'ssl', 'passphrase', $passphrase); // Open a connection to the APNS server $fp = stream_socket_client( 'ssl://gateway.push.apple.com:2195', $err, $errstr, 60, STREAM_CLIENT_CONNECT|STREAM_CLIENT_PERSISTENT, $ctx); if (!$fp) exit("Failed to connect: $err $errstr" . PHP_EOL); echo 'Connected to Apple service. ' . PHP_EOL; // Encode the payload as JSON $body['aps'] = array( 'alert' => $message, 'sound' => 'default' ); $payload = json_encode($body); $result = 'Start'.PHP_EOL; $tokenArray = array('mytoken'); foreach ($tokenArray as $item) { // Build the binary notification $msg = chr(0) . pack('n', 32) . pack('H*', $item) . pack('n', strlen($payload)) . $payload; // Send it to the server $result = fwrite($fp, $msg, strlen($msg)); if (!$result) echo 'Failed message'.PHP_EOL; else echo 'Successful message'.PHP_EOL; } // Close the connection to the server fclose($fp); I have tried encoding $message variable with utf8_encode() but the message received as "THÝS is push". And other ways like iconv() didn't work for me, some of them cropped Turkish characters, some didn't receive at all. I also have header('content-type: text/html; charset: utf-8'); and <meta http-equiv="Content-Type" content="text/html; charset=UTF-8" /> in my page. I don't think the problem appears while I set the value but maybe with pack() function. Any ideas to solve this without replacing characters with English?

    Read the article

  • train wreck. Rails requires RubyGems >= 1.3.2

    - by JZ
    I recently upgraded ruby to ruby 1.8.7 (2009-06-12 patchlevel 174) [i686-darwin10] and I think I broke rails. When I attempt to load rails. I get an odd message. Please help! $ ruby script/server Rails requires RubyGems = 1.3.2. Please install RubyGems and try again: http://rubygems.rubyforge.org $ rails -v Rails 3.0.0.beta $ gem -v 1.3.6 $ which gem /usr/bin/gem $ whereis gem /usr/bin/gem $ which rails /usr/bin/rails $ whereis rails /usr/bin/rails $ /usr/bin/gem -v 1.3.6 $ /usr/bin/rails -v Rails 3.0.0.beta $ ruby script/console Rails requires RubyGems >= 1.3.2. Please install RubyGems and try again: http://rubygems.rubyforge.org $ gem list rails *** LOCAL GEMS *** rails (3.0.0.beta, 2.3.5, 2.2.2, 1.2.6) $ gem list *** LOCAL GEMS *** abstract (1.0.0) actionmailer (3.0.0.beta, 2.3.5, 2.2.2, 1.3.6) actionpack (3.0.0.beta, 2.3.5, 2.2.2, 1.13.6) actionwebservice (1.2.6) activemerchant (1.4.1) activemodel (3.0.0.beta) activerecord (3.0.0.beta, 2.3.5, 2.2.2, 1.15.6) activerecord-tableless (0.1.0) activeresource (3.0.0.beta, 2.3.5, 2.2.2) activesupport (3.0.0.beta, 2.3.5, 2.2.2, 1.4.4) acts_as_ferret (0.4.3) arel (0.2.pre) authlogic (2.1.3) builder (2.1.2) bundler (0.9.3) calendar_date_select (1.15) capistrano (2.5.2) cgi_multipart_eof_fix (2.5.0) chronic (0.2.3) columnize (0.3.1) compass (0.8.17) daemons (1.0.10) dnssd (0.6.0) erubis (2.6.5) fastercsv (1.5.0) fastthread (1.0.1) fcgi (0.8.7) ferret (0.11.6) flay (1.4.0) flog (2.4.0) gbarcode (0.98.16) gem_plugin (0.2.3) git (1.2.5) haml (2.2.15) haml-edge (2.3.100) highline (1.5.0) hoe (2.4.0) hpricot (0.6.164) i18n (0.3.3) javan-whenever (0.3.7) jeweler (1.4.0) jscruggs-metric_fu (1.1.5) json_pure (1.2.0) libxml-ruby (1.1.2) linecache (0.43) mail (2.1.2) mechanize (0.9.3) memcache-client (1.7.8) mime-types (1.16) mislav-will_paginate (2.3.11) mocha (0.9.7) mojombo-chronic (0.3.0) mongrel (1.1.5) needle (1.3.0) net-scp (1.0.1) net-sftp (2.0.1, 1.1.1) net-ssh (2.0.4, 1.1.4) net-ssh-gateway (1.0.0) nifty-generators (0.3.0) nokogiri (1.4.0) openrain-action_mailer_tls (1.1.3) passenger (2.2.5) polyglot (0.2.9) prawn (0.6.3) prawn-core (0.6.3) prawn-format (0.2.3) prawn-layout (0.3.2) prawn-security (0.1.1) rack (1.1.0, 1.0.1) rack-mount (0.4.5) rack-test (0.5.3) rails (3.0.0.beta, 2.3.5, 2.2.2, 1.2.6) railties (3.0.0.beta) rake (0.8.7, 0.8.3) rake-compiler (0.6.0) RedCloth (4.1.1) reek (1.2.6) relevance-rcov (0.9.2.1) rmagick (2.12.2) roodi (2.1.0) rsl-stringex (1.0.3) rspec (1.2.9) rspec-rails (1.2.9) ruby-debug (0.10.3) ruby-debug-base (0.10.3) ruby-openid (2.1.2) ruby-yadis (0.3.4) ruby2ruby (1.2.4) ruby_parser (2.0.4) rubyforge (2.0.3) rubygems-update (1.3.6, 1.3.5) rubynode (0.1.5) searchlogic (2.3.9) sexp_processor (3.0.3) spree (0.9.4) sqlite3-ruby (1.2.5, 1.2.4) termios (0.9.4) test-unit (2.0.5) text-format (1.0.0) text-hyphen (1.0.0) thor (0.13.0) tlsmail (0.0.1) topfunky-gruff (0.3.5) treetop (1.4.3) tzinfo (0.3.16) xmpp4r (0.4)

    Read the article

  • How do you unit test the real world?

    - by Kim Sun-wu
    I'm primarily a C++ coder, and thus far, have managed without really writing tests for all of my code. I've decided this is a Bad Idea(tm), after adding new features that subtly broke old features, or, depending on how you wish to look at it, introduced some new "features" of their own. But, unit testing seems to be an extremely brittle mechanism. You can test for something in "perfect" conditions, but you don't get to see how your code performs when stuff breaks. A for instance is a crawler, let's say it crawls a few specific sites, for data X. Do you simply save sample pages, test against those, and hope that the sites never change? This would work fine as regression tests, but, what sort of tests would you write to constantly check those sites live and let you know when the application isn't doing it's job because the site changed something, that now causes your application to crash? Wouldn't you want your test suite to monitor the intent of the code? The above example is a bit contrived, and something I haven't run into (in case you haven't guessed). Let me pick something I have, though. How do you test an application will do its job in the face of a degraded network stack? That is, say you have a moderate amount of packet loss, for one reason or the other, and you have a function DoSomethingOverTheNetwork() which is supposed to degrade gracefully when the stack isn't performing as it's supposed to; but does it? The developer tests it personally by purposely setting up a gateway that drops packets to simulate a bad network when he first writes it. A few months later, someone checks in some code that modifies something subtly, so the degradation isn't detected in time, or, the application doesn't even recognize the degradation, this is never caught, because you can't run real world tests like this using unit tests, can you? Further, how about file corruption? Let's say you're storing a list of servers in a file, and the checksum looks okay, but the data isn't really. You want the code to handle that, you write some code that you think does that. How do you test that it does exactly that for the life of the application? Can you? Hence, brittleness. Unit tests seem to test the code only in perfect conditions(and this is promoted, with mock objects and such), not what they'll face in the wild. Don't get me wrong, I think unit tests are great, but a test suite composed only of them seems to be a smart way to introduce subtle bugs in your code while feeling overconfident about it's reliability. How do I address the above situations? If unit tests aren't the answer, what is? Thanks!

    Read the article

  • When to delete newly deprecated code?

    - by John
    I spent a month writing an elaborate payment system that handles both credit card payments and electronic fund transfers. My work was used on production server for about a month. I was told recently by the client that he no longer wants to use the electronic fund transfer feature. Because the way I had to interface and communicate with the credit card gateway is drastically different from the electronic fund transfer api (eg. the cc company gives transaction responses immediately after an http request, while the eft company gives transaction responses 5 business days after an http request), I spent a lot of time writing my own API to abstract common function calls like function payment(amount, pay_method,pay_freq) function updateRecurringSchedule(user_id,new_schedule) etc.. Now that the client wants to abandon the EFT feature, all my work for this abstracted payments API is obsolete. I'm deliberating over whether I should scrap my work. Here's my pro vs. con for scrapping it now: PRO 1: Eliminate code bloat PRO 2: New developers do not need to learn MY API. They only need to read the CC company's API PRO 3: Because the EFT company did not handle recurring payment schedules, refunds, and validation, I wrote my own application to do it. Although the CC company's API permitted this functionality, I opted to use mine instead so that I could streamline my code. now that EFT is out of the picture, I can delete all this confusing code and just rely on the CC company's sytsem to manage recurring billing, payment schedules, refunds, validations etc... CON 1: Although I can just delete the EFT code, it still takes time to remove the entire framework consolidates different payment systems. CON 2: with regards to PRO 3, it takes time to build functionality that integrates the payment system more closely with the CC company. CON 3: I feel insecure deleting all this work. I don't think I'll ever use it again. But, for some inexplicable reason, I just don't feel comfortable deleting this work "right now". So my question is, should I delete one month's worth recent development? If yes, should I do it immediately or wait X amount of time before doing so?

    Read the article

  • Twitter RSS feed, [domdocument.load]: failed to open stream:

    - by dave1019
    hi i'm using the following: <?php $doc = new DOMDocument(); $doc->load('http://twitter.com/statuses/user_timeline/XXXXXX.rss'); $arrFeeds = array(); foreach ($doc->getElementsByTagName('item') as $node) { $itemRSS = array ( 'title' => $node->getElementsByTagName('title')->item(0)->nodeValue, 'desc' => $node->getElementsByTagName('description')->item(0)->nodeValue, 'link' => $node->getElementsByTagName('link')->item(0)->nodeValue, 'date' => $node->getElementsByTagName('pubDate')->item(0)->nodeValue ); array_push($arrFeeds, $itemRSS); } for($i=0;$i<=3;$i++) { $tweet=substr($arrFeeds[$i]['title'],17); $tweetDate=strtotime($arrFeeds[$i]['date']); $newDate=date('G:ia l F Y ',$tweetDate); if($i==0) { $b='style="border:none;"'; } $tweetsBox.='<div class="tweetbox" ' . $b . '> <div class="tweet"><p>' . $tweet . '</p> <div class="tweetdate"><a href="http://twitter.com/XXXXXX">@' . $newDate .'</a></div> </div> </div>'; } return $tweetsBox; ?> to return the 4 most recent tweets from a given timeline (XXXXX is the relevant feed) It seems to work fine but i've recently been getting the following error sporadically: PHP error debug Error: DOMDocument::load(http://twitter.com/statuses/user_timeline/XXXXXX.rss) [domdocument.load]: failed to open stream: HTTP request failed! HTTP/1.1 502 Bad Gateway I've read that the above code is dependant on Twitter beign available and I know it gets rather busy sometimes. Is there either a better way of receiving twits, or is there any kind of error trapping i could do to just to display "tweets are currently unavailable..." ind of message rather than causing an error. I'm usnig ModX CMS so any parse error kills the site rather than just ouputs a warning. thanks.

    Read the article

  • Weird Datagrid / paint behaviour

    - by Shane.C
    The scenario: A method sends out a broadcast packet, and returned packets that are validated are deemed okay to be added as a row in my datagrid (The returned packets are from devices i want to add into my program). So for each packet returned, containing information about a device, i create a new row. This is done by first sending packets out, creating rows and adding them to a list of rows that are to be added, and then after 5 seconds (In which case all packets would have returned by then) i add the rows. Here's a few snippets of code. Here for each returned packet, i create a row and add it to a list; DataRow row = DGSource.NewRow(); row["Name"] = deviceName; row["Model"] = deviceModel; row["Location"] = deviceLocation; row["IP"] = finishedIP; row["MAC"] = finishedMac; row["Subnet"] = finishedSubnet; row["Gateway"] = finishedGateway; rowsToAdd.Add(row); Then when the timer elapses; void timerToAddRows_Elapsed(object sender, System.Timers.ElapsedEventArgs e) { timerToAddRows.Enabled = false; try { int count = 0; foreach (DataRow rowToAdd in rowsToAdd) { DGSource.Rows.Add(rowToAdd); count++; } rowsToAdd.Clear(); DGAutoDevices.InvokeEx(f => DGAutoDevices.Refresh()); lblNumberFound.InvokeEx(f => lblNumberFound.Text = count + " new devices found."); } catch { } } So at this point, each row has been added, and i call the re paint, by doing refresh. (Note: i've also tried refreshing the form itself, no avail). However, when the datagrid shows the rows, the scroll bar / datagrid seems to have weird behavour..for example i can't highlight anything with clicks (It's set to full row selection), and the scroll bar looks like so; Calling refresh doesn't work, although if i resize the window even 1 pixel, or minimize and maximise, the problem is solved. Other things to note : The method that get's the packets and adds the rows to the list, and then from the list to the datagrid runs in it's own thread. Any ideas as to something i might be missing here?

    Read the article

  • Run CGI in IIS 7 to work with GET without Requiring POST Request

    - by Mohamed Meligy
    I'm trying to migrate an old CGI application from an existing Windows 2003 server (IIS 6.0) where it works just fine to a new Windows 2008 server with IIS 7.0 where we're getting the following problem: After setting up the module handler and everything, I find that I can only access the CGI application (rdbweb.exe) file if I'm calling it via POST request (form submit from another page). If I just try to type in the URL of the file (issuing a GET request) I get the following error: HTTP Error 502.2 - Bad Gateway The specified CGI application misbehaved by not returning a complete set of HTTP headers. The headers it did return are "Exception EInOutError in module rdbweb.exe at 00039B44. I/O error 6. ". This is a very old application for one of our clients. When we tried to call the vendor they said we need to pay ~ $3000 annual support fee in order to start the talk about it. Of course I'm trying to avoid that! Note that: If we create a normal HTML form that submits to "rdbweb.exe", we get the CGI working normally. We can't use this as workaround though because some pages in the application link to "rdbweb.exe" with normal link not form submit. If we run "rdbweb.exe". from a Console (Command Prompt) Window not IIS, we get the normal HTML we'd typically expect, no problem. We have tried the following: Ensuring the CGI module mapped to "rdbweb.exe".in IIS has all permissions (read, write, execute) enabled and also all verbs are allowed not just specific ones, also tried allowing GET, POST explicitely. Ensuring the application bool has "enable 32 bit applications" set to true. Ensuring the website runs with an account that has full permissions on the "rdbweb.exe".file and whole website (although we know it "read", "execute" should be enough). Ensuring the machine wide IIS setting for "ISAPI and CGI Restrictions" has the full path to "rdbweb.exe".allowed. Making sure we have the latest Windows Updates (for IIS6 we found knowledge base articles stating bugs that require hot fixes for IIS6, but nothing similar was found for IIS7). Changing the module from CGI to Fast CGI, not working also Now the only remaining possibility we have instigated is the following Microsoft Knowledge Base article:http://support.microsoft.com/kb/145661 - Which is about: CGI Error: The specified CGI application misbehaved by not returning a complete set of HTTP headers. The headers it did return are: the article suggests the following solution: Modify the source code for the CGI application header output. The following is an example of a correct header: print "HTTP/1.0 200 OK\n"; print "Content-Type: text/html\n\n\n"; Unfortunately we do not have the source to try this out, and I'm not sure anyway whether this is the issue we're having. Can you help me with this problem? Is there a way to make the application work without requiring POST request? Note that on the old IIS6 server the application is working just fine, and I could not find any special IIS configuration that I may want to try its equivalent on IIS7.

    Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >