Search Results

Search found 39386 results on 1576 pages for 'public ip'.

Page 83/1576 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

  • Which software could I use to setup a 4in6 IP tunnel (RFC 2473) on GNU/Linux

    - by Mildred
    Here is my problem. I have a server A that has two IP addresses. One public IPv4 and one IPv6. Server B has only one IPv6 address. I want to host most of my services on server B (because I have more disk space on it, I can control it better) but I need the IPv4 of the server A. I would like to set up a 4in6 tunnel (RFC 2473) between A and B so that I can transfer the traffic from the IPv4 address in A to B. If needed, I can request another IPv4 address on the server A, but I'd prefer not to. My question is: which software use to do the 4in6 tunnelling? I suppose OpenVPN can do the thing, but is there any implementation of the 4in6 protocol on Linux? A little more challenging: the IPv4 address comes from a venet interface, which cannot be bridged. How could I transfer ownership of this address I don't use on server A to the server B? Thank you

    Read the article

  • How to send SNMP trap to different IP

    - by user147685
    I have the an ASCII message of SNMP traps, how can i sent it to different IP address? i dont want to use email instead. Given a IP address and the port, of that receiver machine. PLease tell me the solution or where can i get references to the command at least. coz i could find anything regarding it. PLease...Hope someone can help me.. thank you very much. regards, dunk

    Read the article

  • second ip address on the same interface but on a different subnet

    - by fptstl
    Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

    Read the article

  • ASP.NET MVC3 checkbox dropdownlist create [migrated]

    - by user95381
    i'm new in asp.net MVC and I/m use view model to poppulate the dropdown list and group of checkboxes. I use SQL Server 2012, where have many to many relationships between Students - Books; Student - Cities. I need collect StudentName, one city and many books for one student. I have next questions: 1. How can I get the values from database to my StudentBookCityViewModel? 2. How can I save the values to my database in [HttpPost] Create method? Here is the code: MODEL public class Student { public int StudentId { get; set; } public string StudentName { get; set; } public ICollection<Book> Books { get; set; } public ICollection<City> Cities { get; set; } } public class Book { public int BookId { get; set; } public string BookName { get; set; } public bool IsSelected { get; set; } public ICollection<Student> Students { get; set; } } public class City { public int CityId { get; set; } public string CityName { get; set; } public bool IsSelected { get; set; } public ICollection<Student> Students { get; set; } } VIEW MODEL public class StudentBookCityViewModel { public string StudentName { get; set; } public IList<Book> Books { get; set; } public StudentBookCityViewModel() { Books = new[] { new Book {BookName = "Title1", IsSelected = false}, new Book {BookName = "Title2", IsSelected = false}, new Book {BookName = "Title3", IsSelected = false} }.ToList(); } public string City { get; set; } public IEnumerable<SelectListItem> CityValues { get { return new[] { new SelectListItem {Value = "Value1", Text = "Text1"}, new SelectListItem {Value = "Value2", Text = "Text2"}, new SelectListItem {Value = "Value3", Text = "Text3"} }; } } } Context public class EFDbContext : DbContext{ public EFDbContext(string connectionString) { Database.Connection.ConnectionString = connectionString; } public DbSet<Book> Books { get; set; } public DbSet<Student> Students { get; set; } public DbSet<City> Cities { get; set; } protected override void OnModelCreating(DbModelBuilder modelBuilder) { modelBuilder.Entity<Book>() .HasMany(x => x.Students).WithMany(x => x.Books) .Map(x => x.MapLeftKey("BookId").MapRightKey("StudentId").ToTable("StudentBooks")); modelBuilder.Entity<City>() .HasMany(x => x.Students).WithMany(x => x.Cities) .Map(x => x.MapLeftKey("CityId").MapRightKey("StudentId").ToTable("StudentCities")); } } Controller public ActionResult Create() { return View(); } [HttpPost] public ActionResult Create() { //I don't understand how I can save values to db context.SaveChanges(); return RedirectToAction("Index"); } View @model UsingEFNew.ViewModels.StudentBookCityViewModel @using (Html.BeginForm()) { Your Name: @Html.TextBoxFor(model = model.StudentName) <div>Genre:</div> <div> @Html.DropDownListFor(model => model.City, Model.CityValues) </div> <div>Books:</div> <div> @for (int i = 0; i < Model.Books.Count; i++) { <div> @Html.HiddenFor(x => x.Books[i].BookId) @Html.CheckBoxFor(x => x.Books[i].IsSelected) @Html.LabelFor(x => x.Books[i].IsSelected, Model.Books[i].BookName) </div> } </div> <div> <input id="btnSubmit" type="submit" value="Submit" /> </div> </div> }

    Read the article

  • IIS reveals internal IP address in content-location field - fix

    - by saille
    Referring: http://support.microsoft.com/kb/q218180/, there is a known issue in IIS4/5/6 whereby it will reveal the internal IP of a web server in the content-location field of the HTTP header. We have IIS 6. I have tried the fix suggested, but it has not worked. The website is configured to send all requests to ASP.NET, and I am wondering if this is why the fix, which addresses IIS configuration, has not worked for us. If this is the case, how would we fix this in ASP.NET? We need to fix this issue in order to pass a security audit.

    Read the article

  • Ingame menu is not working correctly

    - by Johnny
    The ingame menu opens when the player presses Escape during the main game. If the player presses Y in the ingame menu, the game switches to the main menu. Up to here, everything works. But: On the other hand, if the player presses N in the ingame menu, the game should switch back to the main game(should resume the main game). But that doesn't work. The game just rests in the ingame menu if the player presses N. I set a breakpoint in this line of the Ingamemenu class: KeyboardState kbState = Keyboard.GetState(); CurrentSate/currentGameState and LastState/lastGameState have the same state: IngamemenuState. But LastState/lastGameState should not have the same state than CurrentSate/currentGameState. What is wrong? Why is the ingame menu not working correctly? public class Game1 : Microsoft.Xna.Framework.Game { GraphicsDeviceManager graphics; SpriteBatch spriteBatch; IState lastState, currentState; public enum GameStates { IntroState = 0, MenuState = 1, MaingameState = 2, IngamemenuState = 3 } public void ChangeGameState(GameStates newState) { lastGameState = currentGameState; lastState = currentState; switch (newState) { case GameStates.IntroState: currentState = new Intro(this); currentGameState = GameStates.IntroState; break; case GameStates.MenuState: currentState = new Menu(this); currentGameState = GameStates.MenuState; break; case GameStates.MaingameState: currentState = new Maingame(this); currentGameState = GameStates.MaingameState; break; case GameStates.IngamemenuState: currentState = new Ingamemenu(this); currentGameState = GameStates.IngamemenuState; break; } currentState.Load(Content); } public void ChangeCurrentToLastGameState() { currentGameState = lastGameState; currentState = lastState; } public GameStates CurrentState { get { return currentGameState; } set { currentGameState = value; } } public GameStates LastState { get { return lastGameState; } set { lastGameState = value; } } private GameStates currentGameState = GameStates.IntroState; private GameStates lastGameState; public Game1() { graphics = new GraphicsDeviceManager(this); Content.RootDirectory = "Content"; } protected override void Initialize() { ChangeGameState(GameStates.IntroState); base.Initialize(); } protected override void LoadContent() { spriteBatch = new SpriteBatch(GraphicsDevice); currentState.Load(Content); } protected override void Update(GameTime gameTime) { currentState.Update(gameTime); if ((lastGameState == GameStates.MaingameState) && (currentGameState == GameStates.IngamemenuState)) { lastState.Update(gameTime); } base.Update(gameTime); } protected override void Draw(GameTime gameTime) { GraphicsDevice.Clear(Color.CornflowerBlue); spriteBatch.Begin(); if ((lastGameState == GameStates.MaingameState) && (currentGameState == GameStates.IngamemenuState)) { lastState.Render(spriteBatch); } currentState.Render(spriteBatch); spriteBatch.End(); base.Draw(gameTime); } } public interface IState { void Load(ContentManager content); void Update(GameTime gametime); void Render(SpriteBatch batch); } public class Intro : IState { Texture2D Titelbildschirm; private Game1 game1; public Intro(Game1 game) { game1 = game; } public void Load(ContentManager content) { Titelbildschirm = content.Load<Texture2D>("gruft"); } public void Update(GameTime gametime) { KeyboardState kbState = Keyboard.GetState(); if (kbState.IsKeyDown(Keys.Space)) game1.ChangeGameState(Game1.GameStates.MenuState); } public void Render(SpriteBatch batch) { batch.Draw(Titelbildschirm, new Rectangle(0, 0, 1280, 720), Color.White); } } public class Menu:IState { Texture2D Choosescreen; private Game1 game1; public Menu(Game1 game) { game1 = game; } public void Load(ContentManager content) { Choosescreen = content.Load<Texture2D>("menubild"); } public void Update(GameTime gametime) { KeyboardState kbState = Keyboard.GetState(); if (kbState.IsKeyDown(Keys.Enter)) game1.ChangeGameState(Game1.GameStates.MaingameState); if (kbState.IsKeyDown(Keys.Escape)) game1.Exit(); } public void Render(SpriteBatch batch) { batch.Draw(Choosescreen, new Rectangle(0, 0, 1280, 720), Color.White); } } public class Maingame : IState { Texture2D Spielbildschirm, axe; Vector2 position = new Vector2(100,100); private Game1 game1; public Maingame(Game1 game) { game1 = game; } public void Load(ContentManager content) { Spielbildschirm = content.Load<Texture2D>("hauszombie"); axe = content.Load<Texture2D>("axxx"); } public void Update(GameTime gametime) { KeyboardState keyboardState = Keyboard.GetState(); float delta = (float)gametime.ElapsedGameTime.TotalSeconds; position.X += 5 * delta; position.Y += 3 * delta; if (keyboardState.IsKeyDown(Keys.Escape)) game1.ChangeGameState(Game1.GameStates.IngamemenuState); } public void Render(SpriteBatch batch) { batch.Draw(Spielbildschirm, new Rectangle(0, 0, 1280, 720), Color.White); batch.Draw(axe, position, Color.White); } } public class Ingamemenu : IState { Texture2D Quitscreen; private Game1 game1; public Ingamemenu(Game1 game) { game1 = game; } public void Load(ContentManager content) { Quitscreen = content.Load<Texture2D>("quit"); } public void Update(GameTime gametime) { KeyboardState kbState = Keyboard.GetState(); if (kbState.IsKeyDown(Keys.Y)) game1.ChangeGameState(Game1.GameStates.MenuState); if (kbState.IsKeyDown(Keys.N)) game1.ChangeCurrentToLastGameState(); } public void Render(SpriteBatch batch) { batch.Draw(Quitscreen, new Rectangle(200, 200, 200, 200), Color.White); } }

    Read the article

  • Hosting custom domains with IP address flexibility

    - by F21
    I am building a small service where users will be assigned a subdomain such as: myusername.myservice.com anotheruser.myservice.com I know that I can set up a wildcard vhost and using some configuration regex, serve the files like so: myusername.myservice.com ===> /var/www/myusername anotherusername.myservice.com ===> /var/www/anotherusername The problem is that I would like to allow users to alias their own domain names to their service. I understand that for the webserver, once the user adds the domain via my web interface, I can easily create a vhost for the domain in nginx and then refresh the webserver. The problem is that I would prefer to NOT let the users add an A record of my webserver's IP address as I would prefer to keep things flexible (when we upgrade our infrastructure to something more complex to scale). What is the best way to achieve this?

    Read the article

  • IIS reveals internal IP address in content-location field

    - by saille
    Referring: http://support.microsoft.com/kb/q218180/, there is a known issue in IIS4/5/6 whereby it will reveal the internal IP of a web server in the content-location field of the HTTP header. We have IIS 6. I have tried the fix suggested, but it has not worked. The website is configured to send all requests to ASP.NET, and I am wondering if this is why the fix, which addresses IIS configuration, has not worked for us. If this is the case, how would we fix this in ASP.NET? We need to fix this issue in order to pass a security audit.

    Read the article

  • HOSTS File Edit in Windows 7 Not Effective - Pinging URL Still Shows Original IP Address

    - by Sootah
    I've edited my HOSTS file on my Windows 7 Ultimate PC to re-route a couple of URLs so that they point to 127.0.0.1, but after saving the file (and re-opening to verify the changes were written) and pinging them they still reply with the actual IP instead of being redirected to 127.0.0.1 as they should be. At least, that's how it worked in XP, Vista, etc. I even went so far as to restart my DNS service on the machine via services.msc; but no dice. So - I would imagine that Windows 7 keeps the HOSTS file there for legacy purposes and doesn't actually use it anymore. Is there a way to make W7 pay attention to the HOSTS file? In the event that you can't do that, where would I go to edit where these URLs point to? Thanks in advance! -Sootah

    Read the article

  • Get client ip with python

    - by Elad
    Hi, I'm a newbie in python. I want to write a simple web that prints the client ip on screen my http.conf Handler: AddHandler mod_python .py PythonHandler mod_python.publisher PythonDebug On The cgi.escape(os.environ["REMOTE_ADDR"]) return this error: KeyError: 'REMOTE_ADDR' and I just get lost with the BaseHTTPRequestHandler so what is the simple way to get the client ip? thank you.

    Read the article

  • Asp.Net(C#) Jquery Ajax with WebMethod In Public Method Call

    - by oraclee
    Hi All; Aspx Page: $(document).ready(function() { $("#btnn").click(function() { $.ajax({ type: "POST", url: "TestPage.aspx/emp", data: "{}", contentType: "application/json; charset=utf-8", dataType: "json", success: function(msg) { } }); }); }); CodeBehind: public void grdload() { GridView1.DataSource = GetEmployee("Select * from Employee"); GridView1.DataBind(); } [WebMethod] public static void emp() { TestPage re = new TestPage(); re.grdload(); } I Can't Gridview Data Load ? How To Make GridView Data Load? Thank You

    Read the article

  • Get IP Address Information such as Country, LatLong, City using Google Maps Data API

    - by Nullstr1ng
    Can I use Google Maps Data API to get the IP Address informations such as Country, LatLong, City, etc. The result will be in JSON or XML format that I can parse through C#. Is there any C# Library for Google Maps Data API? I found this interesting site http://www.ipinfodb.com/ip_location_api_json.php this guys even offer their IP address location database http://ipinfodb.com/ip_database.php

    Read the article

  • Linux router and firewall with IP accounting

    - by Andrew
    I'm working on a project to replace my organisation's aging Slackware gateway/router/firewall machine in our colo rack. Previously we used rc.firewall but we are now looking for something more modern and easily configurable. The requirements are: Act as a gateway router & firewall Port forwarding to a Terminal Server in the colo IP/traffic accounting, preferably accessible via SNMP (already using cacti for other servers) Possibility of acting as a PPTP server & routing these connections Is not an out-of-the-box Cisco product (don't have the finances or support to maintain it) I'd prefer to use Ubuntu or some other Debian-based distro but something that integrates everything we're looking for is certainly an option if it offers all the desired features and is easy to configure. Is there a simple set of packages that will provide me with the Firewall & Accounting features, or am I best served with a custom-built distro / other solution?

    Read the article

  • Troubleshooting MySQL : can connect to localhost but not to 127.0.0.1 or IP

    - by mireille raad
    Hello, I'd appreciate some help on this, it is bit tricky to find the correct keywords to google :) Using PHP i am able to connect using the following connection string : $link = mysql_connect('localhost', 'wlek' , 'wlek'); but when i use 127.0.0.1 or 10.10.40.15 (self-IP), i am getting connection failed Could not connect: Can't connect to MySQL server on '10.10.40.15' (13) I used yum install mysql , yum install php yum install php-mysql 1 - is there anything more i should install for php ? 2 - any troubleshooting tips ? 3 - what keywords, links do u recommend | % | mir | xdb | | 10.10.40.15 | mir | xdb | | localhost | mir | xdb | [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql port=3306 bind-address=0.0.0.0 old_passwords=1 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid ~ appreciate it :)

    Read the article

  • reduce timeout when connecting to wrong IP (XP-XP, windows explorer)

    - by Viki
    I have many shortcuts in the form \10.0.0.123\path in Windows Explorer (XP). Some of the IPs are sometimes dead (those vmware machines that are inactive). The problem is, when I try to open "Properties" on such shortcut (to correct the IP, or to delete it), Windows Explorer freezes for minutes. For very long time. Start menu freezes, too. This is very inconvenient. How can I reduce the windows explorer timeout when it is probing the connection to another XP share ?

    Read the article

  • Can i have a Asterisk IP PBX Server Behind ISA 2000

    - by garyb32234234
    Hello Is it a simple procedure to configure ISA Server 2000 to allow an Asterisk IPPBX connect to SIP provider. On asterisk forums they say the ISA has difficulties handling SIP, softphones that i have installed behind the firewall work fine with the provider when the firewall client is installed on the workstation. With asterisk being a linux based system this will not be an option. Is the config a matter setting up port forwarding, is this a more complicated task on ISA server than just selecting the ports i need and then the ip of the internal machine i want to forward them to? UPDATE: I dont think this is possible from what ive researched Regards Gary

    Read the article

  • Can't access an internal IIS web site via IP address, only hostname

    - by chris-untrod-com
    I have a machine on my home network running Windows Server 2008 (IIS7) with a web application running under default website called HTCOMNET. The network is just on a Windows Workgroup. The server is named nas1 and has a (dynamically assigned) IPv4 address of 192.168.2.12. I can ping 192.168.2.12. When I ping the machine by name ("nas1"), the hostname resolves to an IPv6 link-local address (as opposed to the ipv4 address). In a browser, I can go to http://nas1/HTCOMNET/ and IIS serves the site, no problem. But if I go to http://192.168.2.12/HTCOMNET, no dice. I have all the windows firewalls turned off. Any idea what's going on? I can't for the life of me figure out why I can't hit IIS via the IP. I feel like it's something really obvious, but i can't figure out what. Thanks!

    Read the article

  • Setting Up an IP Camera in ZoneMinder from Ubuntu

    - by Chris S
    I recently bought a TV-IP312W wireless IP camera. I've completed the basic setup on the camera itself, and confirmed I can stream video using the utility CamViewer. Now I'm trying to access the camera from ZoneMinder, so I can setup monitors and alerts. However, I'm finding the documentation a bit laking. Following the tutorial and a forum post, I've install ZoneMinder, and can access the web interface, but I'm getting stuck at the "Check that your Camera Works!" section. I can add a monitor, but after I add the configuration: Source Type: FFMPEG Source Path: http://192.168.1.105/cgi/mjpg/mjpeg.cgi?.mjpeg all I get is a broken image. What am I doing wrong?

    Read the article

  • why my dns always give wrong ip?

    - by xjdrew
    My dns always resolve learnxue.com with wrong IP, even when I change dns server and execute ipconfig /flushdns. answer from 8.8.8.8: > learnxue.com Server: google-public-dns-a.google.com Address: 8.8.8.8 Non-authoritative answer: Name: learnxue.com Addresses: 97.74.42.79 97.74.42.79 answer from 61.147.37.1: > learnxue.com Server: d.center-dns.jsinfo.net Address: 61.147.37.1 Non-authoritative answer: Name: learnxue.com Addresses: 97.74.42.79 97.74.42.79 My friends living in other city, using dns 61.147.37.1, can get right result, as below: > learnxue.com Server: d.center-dns.jsinfo.net Address: 61.147.37.1 Non-authoritative answer: Name: learnxue.com *Addresses: 222.73.173.188* Is my dns hijacked?

    Read the article

  • Best practice for assigning private IP ranges?

    - by Tauren
    Is it common practice to use certain private IP address ranges for certain purposes? I'm starting to look into setting up virtualization systems and storage servers. Each system has two NICs, one for public network access, and one for internal management and storage access. Is it common for businesses to use certain ranges for certain purposes? If so, what are these ranges and purposes? Or does everyone do it differently? I just don't want to do it completely differently from what is standard practice in order to simplify things for new hires, etc.

    Read the article

  • Apache LogFormat IP Address

    - by Hanpan
    I am using the following LogFormat in my httpd.conf: LogFormat "%h %l %u %t \"%r\" %>s \"%{Referer}i\" \"%{User-Agent}i\" %a %t" combined It's working ok, but for some reason the IP address is coming out as ::1. Is there a particular reason why Apache isn't logging the users IP address? Thanks

    Read the article

  • Need MySQL RLIKE expression to exclude certain strings ending in particular characters...

    - by user299508
    So I've been working with RLIKE to pull some data in a new application and mostly enjoying it. To date I've been using RLIKE queries to return 3 types of results (files, directories and everything). The queries (and example results) follow: **All**: SELECT * FROM public WHERE obj_owner_id='test' AND obj_namespace RLIKE '^user/test/public/[-0-9a-z_./]+$' ORDER BY obj_namespace user/test/public/a-test/.comment user/test/public/a-test/.delete user/test/public/directory/ user/test/public/directory/image.jpg user/test/public/index user/test/public/site-rip user/test/public/site-rip2 user/test/public/test-a user/test/public/widget-test **Files**: SELECT * FROM public WHERE obj_owner_id='test' AND obj_namespace RLIKE '^user/test/public/[-0-9a-z_./]+[-0-9a-z_.]+$' ORDER BY obj_namespace user/test/public/a-test/.comment user/test/public/a-test/.delete user/test/public/directory/image.jpg user/test/public/index user/test/public/site-rip user/test/public/site-rip2 user/test/public/test-a user/test/public/widget-test **Directories**: SELECT * FROM public WHERE obj_owner_id='test' AND obj_namespace RLIKE '^user/test/public/[-0-9a-z_./]+/$' ORDER BY obj_namespace user/test/public/directory/ This works well for the above 3 basic scenarios but under certain situations I'll be including special 'suffixes' I'd like to be excluded from the results of queries (without having to resort to PHP functions to do it). A good example of such a string would be: user/test/public/a-test/.delete That data (there are more rows then just obj_namespace) is considered deleted and in the Files and All type queries I'd like it to be omitted within the expression if possible. Same goes for the /.comments and all such meta data will always be in the same format: /.[sometext] I'd hoped to use this feature extensively throughout my application, so I'm hoping there might be a very simple answer. (crosses fingers) Anyway, thanks as always for any/all responses and feedback.

    Read the article

  • Should I use my ISP's DNS, or Google's 8.8.8.8?

    - by Torben Gundtofte-Bruun
    It seems like a good idea to use Google's public DNS 8.8.8.8 and 8.8.4.4 because it's really fast -- much faster than my own ISP's DNS! -- and probably more reliable, too. That seems like a ridiculously quick win for me, and much easier to remember. Assuming we're not all "tin foil hat" about Google, why shouldn't everybody use Google DNS? Note: I've seen this question, but I don't want a comparison to OpenDNS. This is about everyday use by everyday people in their homes. Update: I seem to have put my hand in a wasps' nest of privacy concerns. I appreciate the issue, but I was expecting a more technology-oriented discussion...

    Read the article

  • PHP not working when accessed through a domain name, but works fine when accessed through IP

    - by Allister
    Done a basic setup of Ubuntu Server installing Apache, PHP and mysql through tasksel. When I browse to the IP address of the server it works fine and allows me to render PHP scripts fine. So I added a DNS entry for the server onto my local DNS server, calling it webdev.lazer.net When I go to this domain name through my browser it renders HTML documents fine but if I try to view PHP scripts it doesn't render and downloads in plain text to the browser (As if the PHP parser isn't rendering .php documents). I'm sure its some rookie mistake, but any help would be appreciated. Thanks

    Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >