Search Results

Search found 4765 results on 191 pages for 'wireless printers'.

Page 83/191 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

• NetBSD Networking

  - by Mike

  Hello, everyone! I have an old Toshiba Satellite 4015CDT, with Pentium II MMX, 32MB RAM, 4GB HDD. It also has one USB 1.0 port, parallel and serial ports, a 3.5" floppy drive and a CD-ROM drive (probably almost dead). I've installed NetBSD on this machine (full install) and now I want to connect it to the Internet. Although it has one PCMCIA modem card in it, it is obviously not an option. I've narrowed down my available options to the following: Connect a USB wireless adapter. I have a Realtek RTL8192 adapter, but although the system gives me the device's name (through dmesg) it fails to recognize it as a network adapter. Connect the laptop to another machine through a serial connection, so that the other machine will serve as a bridge to the Internet. Here is the page from the NetBSD documentation on serial connections. Unfortunately, I was not able to find anything on bridging there. I would very much appreciate your suggestions on the topic. Thanks in advance.

  Read the article

• What exactly is a Mobile mouse? + Mouse Recommendation

  - by chobo2

  I am really disappointed with Logitech. My first cordless wireless mouse was from them and it lasted like 5 years. So I decided to get another one from them http://www.futureshop.ca/catalog/proddetail.asp?logon=&langid=EN&sku_id=0665000FS10099373&catid= And this mouse sucks bad. After 6 months it broke. I returned it under warranty and got a new one now 4-6 month later it is on the verge of breaking again.... You pay like $50 for this mouse and it lasts like 6 months that sad. I just lost faith in Logitech mice as I remember my bro also had a logitech mouse too and it broke after like 6 months. He then bought another logitech mouse(different model) that has been working for maybe 2 years(and no signs of breaking) but I am not crazy about the mouse(I don't like the 2 buttons by the wheel) and I not sure if they even sell it(maybe they got rid of it because it lasts too long). http://www.tigerdirect.ca/applications/SearchTools/item-details.asp?EdpNo=1578495&CatId=1285 So I am looking at a Microsoft mouse. http://www.futureshop.ca/catalog/proddetail.asp?logon=&langid=EN&sku_id=0665000FS10125565&catid= I am looking at this one but I am not sure what they mean by mobile mouse. I think that is what MS calls notebook mice. So I am not sure if this would be a good mouse to get for a desktop. I see it uses like a micro usb receiver but I am not sure if it is smaller then a standard mouse. But almost all the mice I looked at at futureshop.ca or staples are labeled notebook mice or mobile mice. So not sure what mice would be right for me. I don't want a corded one though. I really liked the LX6 design alot but it can't last more than 6 months. Thanks

  Read the article

• Arch Linux drops me on my school network.

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try.

  Read the article

• Router slowing my connection?

  - by Roberto

  I have a Linksys WRT54G and I pay for a 12Mbps connection. I've been testing my connection using speedtest.net for many days and always get 8Mbps. I called the support and they told me to bypass the router and test. I did it and got 16Mbps (much more than I pay for), so I thought "this guy just changed my speed so can he blame my router", and he blamed it. But to my surprise, everytime I bypass the router I get 16Mbps and when I use the router I get 8Mbps. Is this guy trolling me somehow (configuring the VOIP-modem-stuff to different profiles depending o the MAC address connecting to it) or is my router a POS? How can I find out? I don't know what's the thing the router connects to, it's a kind of VOIP adapter; the link is this one, but unfortunately I don't think you'll understand because it's in Portuguese. I know they can remotely connect to it, that's the origin of my conspiracy theory :) I just tested wired to the router and got 10Mbps (and still 8Mbps on wifi and 16Mbps without router) O_o I'm 5cm away from my router, so no obstacles to interfere, right? ------ UPDATE ------- It's a WRT54G V8, I'm using firmware v8.00.7 (will install 8.00.8 tomorrow, but I saw that it's only a minor fix to UPnP denial of service security vulnerability). Results: IPerf LAN-LAN: 80Mbps IPerf LAN-WLAN: 19Mbps (therefore we can ignore wireless issues/settings) I wasn't able to make the (W)LAN-WAN NAT-enabled test with IPerf, I get a connection refused error. I'm not sure if did it right: ran in server mode, configured router to forward that port to my IP and tried to connect to my internet IP that got from this site. I don't think there is a way to disable NAT using this firmware. Question: Let's suppose it's an underpowered hardware issue. Is it right to assume that custom firmwares could resolve the issue because they are possibly better implemented and would make better use of the router resources? I couldn't find any references pointing to wired performance improvements with the use of custom firmware.

  Read the article

• How to use connectify to share files between 2 laptops, one running Windows 7?

  - by p2pnode

  I have 2 laptops one running XP and another Windows 7. Both have WiFi-card installed. I want to be able to share files between these 2 machines and then in next step also be able to share internet connection. I have heard that Connectify on Windows 7 is a very handy and easy tool to set up a hotspot and other machines even XP,Vista can connect to this host hotspot and share files and internet connection. I am able to search for the network (set on host) on my client machine. But how to share files? I don't see any such menu or anything. Also after I have installed connectify on Windows 7, I am not able to connect to internet using data card. It throws error that "Error 31:A A device attached to the system is not functioning". And on client machine, if I connect to data card, as well as connect to wireless network setup by host machine, I no longer am able to access internet, even though the data card is connected. The browser throws error: Please help. Any other utility similar to connectify etc?

  Read the article

• Browsing Playstation 3 from Ubuntu Box

  - by zfranciscus

  Hi, My Goal here is to be able to transfer files from my Ubuntu 10.04 box to my PS3 over a wireless network. My PS3 and my Ubuntu Box is on the same home network. These are some stuff that I tried: I can't see my PS 3 from 'Places ? Network' nor other computer that is running on windows. I am still puzzled by this fact. I have not tried ping-ing my PS3. I'll try that later today and post the result in the forum I install PS3MediaServer (http://code.google.com/p/ps3mediaserver/). Someone in the PS3 chat forum (http://www.ps3chat.com/playstation-3...lp-please.html) claims that it will enable your ubuntu box to browse PS3. So I downloaded PS3MediaServer, and ran the software. The status tab keep showing "Waiting ...". It seems that PS3MediaServer can't find my PS3. Some how I feel that 1 and 2 are related somehow.Perhaps that there is something wrong with my Ubuntu network settings that is preventing my ubuntu box from looking up other device on the network. I can go to the Internet fine, but I can't see other device on my network. Does anyone have any experience in this area. I would like to hear your experience and perhaps some solution. Any kind of hints or help will be greatly appreciated. Cheers

  Read the article

• Advice needed for a home network setup (hardware & software) to handle many clients and potentially heavy traffic

  - by posdef

  I have recently decided to re-structure the home network of our flatshare here. Here's a quick outline of the situation. I envision to have the following 4 devices connected to the router via cable: Xbox 360 IP phone Printer QNAP server (Web, File and Multimedia) We are three people living here, so on top of that there will be to 5-6 computers/mobile devices connecting as wireless clients. My goal is to be able to transfer files (when needed) between the computer and the Multimedia server, which I can reach via 360 and play on the TV. I also would like to keep a high level of security; right now I have the encryption on WPA2 and MAC filtering. I don't believe the web server will get heavy traffic, though I would like to have it responsive. Likewise, I don't have a habit of downloading via torrent etc, but I greatly appreciate my network being responsive and fast, especially when I am browsing or streaming high quality media. Now my questions are: is this setup feasible? smart? efficient? can this be improved somehow? my current router (D-Link DI624) and the previous one (DI-524) used to have spontaneous drops in network, which I find highly irritating. I don't believe in my router, especially now that it completely crashed when I was test-running the setup by transferring a large media file to server while xbox was playing music from the server, and two computers browsing the net. Do I need to get new hardware, if so, any recommendations for a reliable and fast router?

  Read the article

• DD-WRT router causing IP address conflicts across network

  - by r.tanner.f

  My DD-WRT router has lost its mind! I just set up two DD-WRT routers, one as a WAP (working fine) and one in Client Bridge (routed) mode (the problem). Not long after setup I started seeing IP address conflicts on other machines. The event log always points the finger at my Client Bridge router's MAC address. Neighbour table overflow The log on my router is flooded with Neighbour table overflow errors. These start a minute or two after boot. The network is rather large, with +200 IP addresses being used in this subnet. The other router shows no such errors. Mass ARP requests from 1.1.1.1 I'm also seeing constant ARP requests (with the problem router's MAC address) from 1.1.1.1. Seems like it's bugging everything on the network for its MAC address and then promptly forgetting it (or never receiving a response). Configuration: Model: Buffalo N600 Firmware: DD-WRT v24SP2-MULTI (03/21/11) Wireless Mode: Client Bridge (routed) I'm not sure what configuration details are relevant and I'd rather not have comments flooded, so just ping me in this chat if you want to know something. Why is my router stealing IP addresses and how can I stop it?

  Read the article

• Having trouble setting up my router

  - by indyK1ng

  I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

  Read the article

• Linksys router cannot change default password

  - by Jessica M.

  My wireless internet suddenly stopped working today. I have Windows 7 and Lindsys WRT54G router. I tried to log into the Linksys setup router page by typing in www.192.168.1.1 into firefox and it prompted me for a username and password as usual. The problem is when i tried to enter my regular username and password it did not work. I finally solved my problem when I came across this post here and the very last post solved my problem. It suggested I try username: root / password: admin. For some reason the username and password has been changed. When i tried username: root / password: admin , it worked and allowed me to get into the Linksys setup page. The problem is I can't change the username or password anymore. Every time I want to log into my Linksys setup page I have to enter username: root / password: admin. I can't change the "WPA shared key" (password). For the security settings I selected WPA2Personal + AES. Also the post said "If the firmware was upgraded to non-linksys firmware - the default will be different" . The problem is I didn't update anything and I'm worried that someone installed a virus or something or somehow changed the firmware on my router. How did I get non-Linksys firmware on my router? EDIT: I figured out how to change the password when I log into the Lynksys setup page. Administration -- Management -- password. I still don't understand if my router firmware was changed or who changed it or if it happened by mistake.

  Read the article

• Port Forwarding(?) TD-W8961nd

  - by rich

  I have a bit of a weird internet setup. I am connected via a decent WiFi connection (from work) which I pick up using a Buffalo Airstation Wireless-G box. This simply picks up the signal and gives me 4 ethernet ports to connect to. That's all fine and works as it should. I also have a TP LINK TD-W8961nd router which used to be connected to the Airstation via an ethernet cable so I could essentially have WiFi access in my house. To cut a long story short I can't remember how the hell I got it to work and I can't find the notes I scribbled down on how to do it. I'm pretty sure I need to tell the router what ip to pick up the internet connection from and have the local wifi as a seperate network. How the hell I do that I have no idea right now. Can anyone give me some advice on this? If you need more information ask and I will be able to do so. Cheers in advance. edit I'm in work at the moment so I can't give 100% details but I will be able to later on.

  Read the article

• Ways to have audio output without wires

  - by viraptor

  I'm trying to find a way of using my home speakers/amp without actually having to connect them. There are two laptops that use them normally (so I don't like changing the connection all the time) and I'd rather move the speakers to a place that's away from the couch. I'm not sure how to do this though... The options I can think of are: some kind of wireless jack-jack connection finally getting a media server Unfortunately I can't find any good product for the first solution. I've seen some headphones which have the receiver integrated and a separate transmitted, so in general the idea is already out there, just not the way I need ;) I've seen also http://www.miccus.com/products/blubridge-mini-jack, but I'd have to have a compatible receiver which I can't find on its own (maybe there's some application that the media server could use?). As far as media server goes... many of the plug servers look really interesting, but I'm not sure how to create an audio output and how to redirect the input really. None of the plug servers I've seen so far advertises the option of audio output jack port. I think this part could be fixed by getting one with an usb port and a separate cheap usb soundcard. I hope that input can be sorted out in some rather simple way. I've got Linux running on both laptops so I hope that would be possible to configure jack/pulse/whatever to use the remote endpoint, or even write a simple local-/dev/dsp:network:media-server-/dev/dsp forwarder. So the main question is... are there better ways? Are there any out of the box solutions? Or maybe this was already done by someone and described somewhere?

  Read the article

• Wiring my internet

  - by u8sand

  I have Verizon internet service and am currently using wifi. My router is in the basement and my desktop computer is 2 floors and on the other side of the house above it... Worst possible positioning but that's just how things worked out. My wireless currently is extremely unstable so I've decide to correct the problem by wiring my computer directly. The problem lies here: when redoing the room next to it (when the wall was open) we went ahead and wired some coaxial cable from our attic to our basement (with plenty of slack on both ends, don't ask me why we didn't go ahead and wire a CAT6 cable). The question is: Can I use the coaxial cable to bring me internet connection? Naturally the router (which needs to stay where it is) takes a coaxial cable input and has Ethernet outputs. So maybe I would have to take a ethernet cable, convert to coaxial-coaxial to my computer, convert back to ethernet. Is this even possible to convert from coaxial to ethernet? Or do I have to attempt to go ahead and fish a cat6 cable through my house. I cannot just split the signal because that would require two routers and two networks (which I don't believe would work with one cable-one ISP correct me if I'm wrong). Thanks

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• PEAP validating a secondary domain suffix

  - by sam

  Probably the title is a little bit confusing, let me explain the situation. Our company wants to implement a corporate wireless lan with PEAP authentication. unfortunately someone made a big mistake in our AD design 10 years ago. The domain name we are using "company.ch" is not owned by company but by someone else. so it is not possible to issue a public SSL certificate for the RADIUS server. Our AD is to big to rename it. We already thought about using our private PKI and rollout the CA certificate via GPO but that would only cover our corporate managed clients but not the BYOD (Smartphones, Tablets, Laptops..) Is there a way to add a secondary domain name like “company2.ch” and issue a public certificate and join that radius to that secondary domain aslwell, and configure that secondary dns suffix via DHCP for all the client pools... or is there another way with for example a new radius server which has his own domain company2.ch which is connected with some kind of trust between the company.ch doamin? sorry i'am not a client server guy.. hopefully you get my drift.!?

  Read the article

• What kernel modules are required for wi-fi to work?

  - by Leonid Shevtsov

  My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

  Read the article

• How is it possible that I can do a host lookup but not a curl?

  - by Daniel Quinn

  Has anyone ever seen this before? Note that this happens not only with google.com, but with every domain I try. It's a wireless connection (WEP), but I'm not sure how that would be relevant: $ curl -v google.com # This takes about 60s to return * getaddrinfo(3) failed for google.com:80 * Couldn't resolve host 'google.com' * Closing connection #0 curl: (6) Couldn't resolve host 'google.com' $ host google.com google.com has address 209.85.148.106 google.com has address 209.85.148.147 google.com has address 209.85.148.99 google.com has address 209.85.148.103 google.com has address 209.85.148.104 google.com has address 209.85.148.105 google.com mail is handled by 30 alt2.aspmx.l.google.com. google.com mail is handled by 40 alt3.aspmx.l.google.com. google.com mail is handled by 50 alt4.aspmx.l.google.com. google.com mail is handled by 10 aspmx.l.google.com. google.com mail is handled by 20 alt1.aspmx.l.google.com. $ cat /etc/resolv.conf # Generated by NetworkManager nameserver 192.168.1.201 $ cat /etc/hosts 127.0.0.1 localhost ::1 localhost $ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.1.254 0.0.0.0 UG 0 0 0 wlan0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• How can I print from my lion mac mini to my windows XP, with simple file sharing?

  - by Jules

  I have quite a complicated setup, perhaps. And a lot of history on this issue, I'm hoping that I don't have to buy a new printer. I've got a HP Wireless USB Print Server, which requires client software, I can't just use it as an IP Printer. The HP software is pretty poor on the mac and is no longer supported and often locks up the printer server and takes some considerable effort to actually print something. Let alone if a windows machine attaches to it first. My printer is an Epson Stylus R285. However, the windows client software is fine and we can print from windows 7 / XP without problem. We have simple file sharing setup as this is the only way I could get windows XP to talk to windows 7. However, I can't seem to get my mac mini to connect as anything other than a guest to my xp machine, to connect to the shared printer. I'm not considering some kind of internet printing as this would seems the simplest solution. But I'm not sure what will work with my setup ?

  Read the article

• Monitor mode 802.11 captures on OSX

  - by Mike A

  I'm trying to determine the difference between capturing 802.11 frames in the following ways on OSX (10.8.5). It's a bit esoteric, but I use "Option 2" to capture frames for later analysis, and am wondering if I'm missing something. Option 1: use "airportd": $sudo /usr/libexec/airportd en0 sniff Option 2: use "airport" followed by tcpdump: sudo /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport --channel= sudo tcpdump -I -P -i en0 -w /tmp/capture.pcap (or alternatvely eliminate the -w and watch packets real-time). From what I can tell: Both commands, according to the wifi icon on OSX, put the interface into 'monitor' mode. Both commands output a pcap file that is readable in both wireshark/tcpdump & Eye PA. Both commands appear to capture management, control and data frames. The rub: Option 1 disconnects you from the network. This is expected, when putting an interface into 'monitor' mode. Option 2 does NOT disconnect you, provided you've set the channel to the same channel your currently connected to. This has a distinct advantage of keeping your connection up while capturing in monitor mode. My question: Option 2 does not seem like it should work, or more specifically, it does not seem like I should be able to remain connected while also capturing frames in monitor mode. On a wired NIC, you can be 'promiscuous' and still send frames, though I didn't think the same was true for wireless NIC. I'm questioning the validity of capturing frames w/ Option 2?

  Read the article

• Create a wifi hotspot in a place where an authentication is required

  - by SoftTimur

  I live in a residence where Internet is provided via cable. Once the computer is connected to the cable, launching a browser will trigger an authentication, I have a username and password to enter, then the internet will be connected. With a gateway (e.g. Wireless Cable Voice Gateway Model CBVG834G) and 2 cables, two PCs can connect to the Internet with my account at the same time. Now the question is, I don't like the cable, and would like to create a wifi hotspot. It seems realizable with the same gateway. According to the instruction on page 2-4 of the manual: Enter http://192.168.0.1 in the address field of your Internet browser. Log in to the gateway with either of the default user names, MSO or admin... However, while connecting to the Internet successfully via cable and the gateway (e.g. google works), opening 192.168.0.1 oddly gives me an error on the browser: Does anyone know what happened? Is it due to the authentication required by my residence? Is there any other way to build a hotspot of wifi? PS: My system is MAC OS

  Read the article

• VLAN for WiFi traffic separation (new to VLANing)

  - by Philip

  I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

  Read the article

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• Asus PCE-N53 11n N600 PCI-E Adapter on 3.x kernel

  - by CITguy

  Problem ASUS PCE-N53 wireless NIC doesn't work for latest versions of the linux kernel. How do I get it working on my system? (Note: I'm posting the answer I've found for others to use.) Installing Driver for Linux 3.x Kernel ASUS provides Linux drivers from their website, but it mentions that the driver supports "Linux Kernel 2.6.x", so it won't work without a some modifications to the driver code. Fortunately, an archlinux forum mentions similar problems and one user was able to create a patch for kernel 3.8.x that seems to work with kernel 3.11.x. Here's how I got it working: Prerequisites Ubuntu: sudo apt-get install build-essential Arch: sudo pacman -S base-devel Steps: 1. Download the driver from the ASUS website The download can be found under "Support Drivers & Tools". 2. Unzip the contents of the downloaded file cd into the new directory 3. Patch The arch forum mentions a 3.8 patch file that needs to be downloaded. Download rt5592sta_fix_64bit_3.8.patch to the current directory. tar -xvf {driver_source.tar.gz} cd into the directory created in previous step patch -p1 < ../rt5592sta_fix_64bit_3.8.patch 4. Compile NOTE: You will need to use sudo for it to compile properly. sudo make sudo make install sudo modprobe rt5592sta 5. Enjoy If all is well, you should now have a working card.

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >