Search Results

Search found 2465 results on 99 pages for 'pci bus'.

Page 84/99 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• Media Center - TV constantly pauses 1/2 second then plays 1 second

  - by Bob

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing. I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card, ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• linux mint VIA sound issue

  - by user2699451

  So I installed linux Mint 15 "Olivia" 64 bit on my Mecer W550EU laptop I have HD Audio with a VIA chipset charles-W55xEU charles # lsmod | grep snd snd_hda_codec_hdmi 36913 1 snd_hda_codec_via 51018 1 snd_hda_intel 39619 5 snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_codec_via,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 97451 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 19 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_via,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device soundcore 12680 1 snd And my sound card charles-W55xEU charles # aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: VT1802 Analog [VT1802 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 2: VT1802 HP [VT1802 HP] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 and my audio device charles-W55xEU charles # lspci -v | grep -A7 -i "audio" 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High `Definition Audio Controller (rev 04)` Subsystem: CLEVO/KAPOK Computer Device 0550 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7c10000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Sometimes when I boot up, soundworks, other times it doenst, it is completely random, so far, no-one on xchat linux help or linux mint forums was able to help me, I have always had issues with sound on VIA chipsets I have: sudo apt-get upgrade && apt-get install mint-meta-cinnamon it seemed to help but after 2-3 reboots, the problem came back, btw, everytime I checked, pulse audio is selected to Duplex Audio Input & Output and alsa mixer is always unmuted!

  Read the article

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• None of usb-controllers are working after a crash

  - by Cray

  So I have a GA-p35-DS4 mboard with a Q6600, running windows7-x64. After a random crash with a bluescreen (not caused by anything particular as I recall), none of the usb-controllers are working. (And none of the devices connected to those usb ports). All the controllers are showed up in the device manager, but every one has a warning-icon (as they are not functioning properly). The windows identifies them correctly, it shows exactly the model of each controller, and it says that the driver is installed. Now, when I try to reinstall the driver (Update driver menu item in the device manager), it tries to find it, finds the driver, but quits saying that the driver was found but could not be installed. Additionally, it displays "This operation requires an interactive window station", whatever that means... Now get this, the same thing happens with a new pci-usb controller card! It is found (actually each time the machine starts, it is found as new hardware), but trying to install drivers leads nowhere, I am getting the same message about an interactive window station. (tried to install drivers from the acoompanying CD) I have tried deleting those devices from device manager and let windows find them again, but that leads to same results. None of the ports on this extension card work either. This should not be a hardware problem, a usb keyboard connected to the builtin usb controller works in bios, and even in another OS running the same computer (old xp installation) What to do? Will I have to reinstall? Can deleting infcache.1 help? Is there some way to let windows remove all old drivers and try to find all hardware again, this time only looking for drivers on a windows install disk or something?

  Read the article

• SATA HDD stuttering on reads (LED on)

  - by jdehaan

  I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

  Read the article

• No signal on monitor after plug it to a linux box

  - by yaroot

  I use my old computer as an NAS, so I remove the monitor after I installed linux on it (disconnect vga cable). I use ssh to control the machine and it works fine. Until some day, after kernel/softare upgrade or messing up some configs, I cannot connect to it through ssh, then I have to plug the monitor back, but the monitor says "No input signal". So I have to restart the computer WITH the monitor connected, and the monitor's back! I think the computer/linux kernel doesn't detect the monitor plug-in event. So how can I start my linux box without a monitor, but when it goes wrong I can still plug my monitor (vga) back and use the console. Edit: just one pci-e video card, has dvi, vga, tv/out (s-video) Edit2: Xorg is not running. I just need the console (CTRL+ALT+F1). The problem is, if the machine booted without a monitor connected, it won't give me a pseudo terminal after I attach the vga cable while it's running. Clearly the monitor is not auto detected as usb device. I'm wondering how to let the monitor auto detected.

  Read the article

• Static noise in headphones

  - by John Murdoch

  I have a Asus P6T based system. I was using the on-board sound (plugging in Logitech X-230 2.1 analog speakers in the green "front speakers" 3.5mm analog output, then plugging in my headphones in that). I was quite happy with the sound quality (didn't hear any static noise if volume was turned down to my normal listening level). Then about a week ago I started having terrible static noise from the left channel, and no normal audio on that left channel. Right channel had more static noise than usual but did have a bit of sound. I tried using the AC'97 in front of my case but that seemed to have no signal. I decided my on-board sound card has gone bad and bought an internal sound card to replace it (Startech 7.1Ch PCI). This fixed the "no sound from left channel problem", but I had much more audible static noise. I decided the card was low quality and/or it had interference from all the other things happening inside the computer case, and bought a Sweex SC016 external USB sound card. But even with that I have static noise in headphones. Positioning the USB sound card differently doesn't seem to help. Trying the other analog outputs (e.g., surround) doesn't help. The static noise in all cases is proportional to the volume. I have tried different headphones, but the situation is situation though perhaps the flavour of the static noise changes slightly. So what are my options? a) Get another, more expensive, external USB sound card hoping the quality will improve? b) Get another, more expensive, internal sound card (PCIe 1x perhaps) hoping the quality will improve? c) Get a dedicated DAC box? d) Get some Hi-Fi earphones? Suggestions? tl;dr - Two different sound cards both still have static noise in headphones.

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• The bottlenecks of any computer, what to look for?

  - by WebDevHobo

  Whether it is a laptop or a desktop, any computer is made up of several pieces of hardware that communicate with each other. Sending data back and forth to ensure that the user gets the desired results. I have seen some theoretical stuff on computers & hardware, but I wonder how it all comes together. CPU RAM Graphics Card L1 CACHE L2 CACHE L3 CACHE FSB ... And all other things. Which is the biggest bottle neck? Why would a person not want/need a big value in one of those categories in certain situations? P.S.: when reading the specs of the i5 750 processor, I came across this description: In place of the FSB, one or more high speed, point-to-point buses called Quick Path Interconnect (QPI) are used, formerly known as Common Serial Interconnect Bus or CSI. QPI features higher bandwidth than the traditional FSB and is better suited to system scaling. What is this, and how does it compare to FSB? EDIT: I am not planning to buy a computer at all. The goal of this question is to understand the internal relation of various hardware pieces, their specific functions and how they work together. For instance, I have heard to a somewhat higher-than-usual amount of L2/L3 Cache can help speed up your computer. What's up with saying that? Also I forgot to mention Hard-disk RPM.

  Read the article

• Running a VM off a USB 2.0 Flash Drive - Mac/Parallels/XP

  - by geerlingguy

  I use a MacBook Air as my primary machine, and the 128GB SSD means space is precious. To save about 10 GB, I've been running Parallels with a Windows XP VM off an external USB hard drive, which performs as well in everyday use as running the VM off the internal SSD. So, I bought a tiny 32GB USB 2.0 flash drive, plugged it into the MacBook Air, formatted it first as ExFAT (which was slow), then as Mac OS Extended (Journaled) (which was also slow), and copied over my VM file, and ran Parallels off it. My full experience is documented here: http://www.midwesternmac.com/blogs/jeff-geerling/running-windows-xp-vm Straight file copies are really fast — 30 MB/sec read (solid the whole time), and 10-11 MB/sec write (solid the whole time). But I noticed that once XP started running, the disk access rates were in the low KB ranges. Are USB flash drives really that poor at random access, or could I possibly be missing something (the format of the flash drive, etc.?)? Of note, I've tried the following, to no great effect: Formatting the drive as either ExFAT or Mac OS Extended (Journaled) Unplugging all other USB devices and turning off Bluetooth (which runs on the right-side-port USB bus). Plugging in the flash drive either direct in the right side port, or the left side port, or into a USB 2.0 hub

  Read the article

• How to give wife emergency access to logins, passwords, etc.?

  - by Torben Gundtofte-Bruun

  I'm the digital guru in my household. My wife is good with email and forum websites but she trusts me with all our important digital stuff -- such as online banking and other things that require passwords, but also family photos and the plethora of other digital things in a modern home. We discuss relevant actions but it's always me that executes the actions. If I should get "hit by a bus" then my wife would be thoroughly stranded -- she would have no idea what digital stuff is where on our computer, how to access it, what online accounts we have, and their login credentials are. It would also leave my many public appearances (personal websites, email accounts, social networks, etc.) unresolved. To complicate things, I'm one of those people who don't use password as my password everywhere; I use a mix of SuperGenPass and LastPass, and also two-factor authentication whenever possible. I don't have much hope that she would find her way through a written explanation of all that in a stressful situation. I could just tell her that she should ask my tech-savvy twin brother and then entrust him with my LastPass master passphrase. I feel that would have a high chance of success, but it's inelegant and leaves my wife without control of the information. How can I ensure that my wife has access to my digital remains?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• AMD 700, 800 series chipset. I'm lost.

  - by Shiki

  I've been an Intel / NVidia user ever since I started using computers. Intel really gone up with the prices, and they won't get cheaper. So I decided to get an AMD. But WHICH one? I mean.. not shopping question but.. what are the differences? Like: 880GMA comes only with a single PCI ex and it looks like a chinese replica (no offense). While 890FX comes with 5PCI-ex for QuadCrossfire. Also.. what's the deal with 7xx series? I mean.. its the same price. Yet its older? Or why is it 7xx? Isn't there a single chipset between? Not chinese YET it's durable/fine for long-term usage? What it should know (desktop stuff): NVidia GPU (Zalman AMP2 GTX 260^2 (one card)) Phenom 1090T cpu A somewhat good audio. Any ideas which is the chipset I'm searching for? If this sounds too much of a shopping question, feel free to edit. I just want some clarification on these chipsets.

  Read the article

• Setting my NIC to full duplex

  - by David

  I am trying to optimize the network speed of my Solaris X86 server, and have discovered that the Cisco 3548 that it is connected to has issues with the NIC in my server. The NIC appears to have not been configured fully, and is coming up 100 half-duplex. The 3548 ports are all set to 100 full. Ideally I'd like to have the server set for 100 full, and have been attempting to configure it using ndd commands. However I have had no results. The following command: -bash-3.00# dladm show-dev rtls0 link: unknown speed: 100 Mbps duplex: unknown The NIC shows up as: pci bus 0x0001 cardnum 0x06 function 0x00: vendor 0x10ec device 0x8139 Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ which should be configurable. I have modified the configuration file from auto config (5) to 100 fdx (4) to no avail. If there is no other choice, I could alter the Cisco 3548 to be 100 half-duplex. However, this solution causes huge performance loss. Currently throughput is about 500Kbps, when it should be around 40Mbps.

  Read the article

• Extend RAID 1 (HP SmartArray P410i) running Linux

  - by Oliver

  I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

  Read the article

• VLC tv card streaming

  - by Franco

  I'm trying to stream the output of my desktop's tv card to my laptop using vlc without success. I have on both pcs ArchLinux installed. I'm stuck here: $ cvlc v4l2:///dev/video0:norm=pal-nc:frequency=543250:size=640x480:channel=0:input-slave=alsa:///dev/dsp:audio=0 --sout '#transcode{vcodec=mp4v,acodec=mpga,vb=3000,ab=256,vt=800000,keyint=80,deinterlace}:standard{access=http,mux=ogg,dst=192.168.0.2:8080}' --ttl 12 VLC media player 1.1.4 The Luggage (revision exported) Blocked: call to unsetenv("DBUS_ACTIVATION_ADDRESS") Blocked: call to unsetenv("DBUS_ACTIVATION_BUS_TYPE") [0x1c9e480] inhibit interface error: Failed to connect to the D-Bus session daemon: /usr/bin/dbus-launch terminated abnormally with the following error: Autolaunch error: X11 initialization failed. [0x1c9e480] main interface error: no suitable interface module [0x1ca1500] main interface error: no suitable interface module [0x1bb3120] main libvlc error: interface "globalhotkeys,none" initialization failed [0x1c9f940] dummy interface: using the dummy interface module... [0x1ca4850] main access out: creating httpd [0x1ebb340] mux_ogg mux: Open And on my laptop: $ vlc http://192.168.0.2:8080 VLC media player 1.1.4.1 The Luggage (revision exported) Blocked: call to unsetenv("DBUS_ACTIVATION_ADDRESS") Blocked: call to unsetenv("DBUS_ACTIVATION_BUS_TYPE") Blocked: call to setlocale(6, "") Blocked: call to sigaction(17, 0xb25c7058, 0xb25c70e4) Warning: call to signal(13, 0x1) Warning: call to signal(13, 0x1) Blocked: call to setenv("ORBIT_SOCKETDIR", "/tmp/orbit-zf", 1) Warning: call to srand(1287690122) Warning: call to rand() Blocked: call to setlocale(6, "") (process:17933): Gtk-WARNING **: Locale not supported by C library. Using the fallback 'C' locale. Warning: call to signal(13, 0x1) Blocked: call to setlocale(6, "") [0x8af5f04] main stream error: cannot pre fill buffer Any idea why this isn't working?

  Read the article

• Gnome 3 gdm fails to start after preupgrade from fedora 14 to 15

  - by digital illusion

  I'm not able to boot fedora 15 in runlevel 5. After all services start, when the login screen should appear, gdm just show a mouse waiting cursor and keeps restarting itself. From /var/log/gdm/\:0-greeter.log Gtk-Message: Failed to load module "pk-gtk-module" /usr/bin/gnome-session: symbol lookup error: /usr/lib/gtk-3.0/modules/libatk-bridge.so: undefined symbol: atk_plug_get_type /usr/libexec/gnome-setting-daemon: symbol lookup error: /usr/lib/gtk-3.0modules/libatk-bridge.so: undefined symbol: atk_plug_get_type Where should atk_plug_get_type be defined? Edit: Here a better description of the error (system-config-network-gui:2643): Gnome-WARNING **: Accessibility: failed to find module 'libgail-gnome' which is needed to make this application accessible /usr/bin/python: symbol lookup error: /usr/lib/gtk-2.0/modules/libatk-bridge.so: undefined symbol: atk_plug_get_type Why there are still references to gtk2? Did preupgrade fail? Attaching upgrade log... it seems gdm was not added, but it is present in the users and groups list. May 26 11:25:52 sysimage sendmail[1076]: alias database /etc/aliases rebuilt by root May 26 11:25:52 sysimage sendmail[1076]: /etc/aliases: 77 aliases, longest 23 bytes, 795 bytes total May 26 11:46:09 sysimage useradd[1793]: failed adding user 'dbus', data deleted May 26 11:53:37 sysimage systemd-machine-id-setup[2443]: Initializing machine ID from D-Bus machine ID. May 26 11:55:28 sysimage useradd[2835]: failed adding user 'apache', data deleted May 26 11:55:38 sysimage useradd[2842]: failed adding user 'haldaemon', data deleted May 26 11:55:43 sysimage useradd[2848]: failed adding user 'smolt', data deleted May 26 11:57:32 sysimage sendmail[3032]: alias database /etc/aliases rebuilt by root May 26 11:57:32 sysimage sendmail[3032]: /etc/aliases: 77 aliases, longest 23 bytes, 795 bytes total May 26 11:57:46 sysimage groupadd[3066]: group added to /etc/group: name=cgred, GID=482 May 26 11:57:47 sysimage groupadd[3066]: group added to /etc/gshadow: name=cgred May 26 11:57:47 sysimage groupadd[3066]: new group: name=cgred, GID=482 May 26 11:58:42 sysimage useradd[3086]: failed adding user 'ntp', data deleted May 26 12:00:13 sysimage dbus: avc: received policyload notice (seqno=2) May 26 12:15:08 sysimage useradd[4950]: failed adding user 'gdm', data deleted May 26 12:24:39 sysimage dbus: avc: received policyload notice (seqno=3) May 26 12:25:24 sysimage useradd[5522]: failed adding user 'mysql', data deleted May 26 12:25:37 sysimage useradd[5533]: failed adding user 'rpcuser', data deleted May 26 12:26:31 sysimage useradd[5592]: failed adding user 'tcpdump', data deleted Any suggestions before I revert installation to F14?

  Read the article

• ifcf-ethx problem

  - by Shahmir Javaid

  Every time i run service networkd restart This is what i get Shutting down interface eth0: Device state: 3 (disconnected) [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown [ OK ] Bringing up loopback interface: Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown Error org.freedesktop.NetworkManagerSettings.InvalidConnection: ifcfg file '/etc/sysconfig/network-scripts/ifcfg-lo' unknown [ OK ] Bringing up interface eth0: ** (process:12951): WARNING **: fetch_connections_done: error fetching user connections: (2) The name org.freedesktop.NetworkManagerUserSettings was not provided by any .service files. Active connection state: activating Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/1 state: activated Connection activated [ OK ] Here is my ifcfg-eth0 # Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller DEVICE=eth0 BOOTPROTO=dhcp DEFROUTE=yes DHCPCLASS= HWADDR=xxx IPV4_FAILURE_FATAL=yes IPV6INIT=no ONBOOT=yes OPTIONS=layer2=1 PEERDNS=yes PEERROUTES=yes TYPE=Ethernet UUID=xxx And my ifcfg-eth1 # Intel Corporation 82541PI Gigabit Ethernet Controller DEVICE=eth1 HWADDR=xxx ONBOOT=no And my ifcfg-lo DEVICE=lo IPADDR=127.0.0.1 NETMASK=255.0.0.0 NETWORK=127.0.0.0 # If you're having problems with gated making 127.0.0.0/8 a martian, # you can change this to something else (255.255.255.255, for example) BROADCAST=127.255.255.255 ONBOOT=yes NAME=loopback Any ideas?

  Read the article

• computer build for extreme tabbed browsing

  - by David Berger

  I'm interested in building or buying a task-specific computer for my brother. His requirements are ridiculously simple: the machine has to be able to wait in hundreds of web-based virtual waiting rooms at once and not crash. To be competitive, he needs to be able to enter the waiting rooms an dauto-refresh them faster. My question is, what priority do I give the different specs? My initial surmise is this: Connection speed (nothing to do with my build, but I kind of think this will be more beneficial than anything I build for him) Memory size -- I don't usually see firefox taking up more than a gig, even when heavily tabbed, but I think one gig for the operating system and two gigs for the browser are necessary. Processor speed -- I think the processor will affect performance, but even something out of date will do what he needs Memory speed/RAM bus -- I doubt this will matter much, but it seems just on this side of irrelevant. Everything else is a non-issue for him. Does this seem to stack up correctly? Also, since he's looking to stay on the cheaper side, and I might end up recommending a refurb to him, is there anything particularly egregious that Vista would do if it came pre-installed? If I build it myself, I'll give him linux, but if I have it shipped to him, I'm not sure I could walk him through the install process for linux, but I probably could walk him through the process to upgrade to Windows 7, if it were somehow worth it.

  Read the article

• Unable to write DVD-R(Blank DVD's)

  - by FrozenKing

  I have a problem in dvd drive i.e. It can read CD/DVD and can write CD and all CD/DVD-RW but cannot write DVD DVD drive model is SH-S203B Samsung; I also have a log file created by nero burning rom 11. Actually the fact is no Blank DVD's are being read in my dvd drive only previously written dvd's can be read! Is this the problem of OS or should I try cleaning the dvd drive or my DVD drive is 4yrs old so is it going to spoil now, since it is showing this type of symptoms! OS = WinXP AV = KIS 2012 DVD Drive = Samsung SH-S203B (Also tried latest firmware and downgrade versions also) IA32 Nero Version: 11.2.4.100 Internal Version: 11,2,4,100 Recorder: <TSSTcorp CDDVDW SH-S203B>Version: SB04 - HA 1 TA 0 - 11.2.4.100 Adapter driver: <Serial ATA> HA 1 Drive buffer : 2048kB Bus Type : via Inquiry data CD-ROM: <TSSTcorp CDDVDW SH-S203B >Version: SB04 - HA 1 TA 0 - 11.2.4.100 Adapter driver: <Serial ATA> HA 1 18:58:10 #37 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 00 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000 18:58:10 #38 SectorVerify 20 File Cdrdrv.cpp, Line 12057 Read errors from sector 0 to 14 <Padding> 18:58:19 #39 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 10 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000 18:58:19 #40 SectorVerify 21 File Cdrdrv.cpp, Line 12057 Read error at sector 15 <Virtual Multisession Info> 18:58:19 #41 SectorVerify 20 File Cdrdrv.cpp, Line 12057 Read errors from sector 16 to 18 <Volume Structure Descriptor Sequence> 18:58:28 #42 SPTI -1511 File SCSIPassThrough.cpp, Line 224 CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1511) CDB Data: 0x28 00 00 00 00 20 00 00 10 00 Sense Key: 0x04 (KEY_HARDWARE_ERROR) Sense Code: 0x3E Sense Qual: 0x02 Sense Area: 0x70 00 04 00 00 00 00 0A 00 00 00 00 3E 02 Buffer x08047340: Len x8000

  Read the article

• What do I need to consider when buying hardware to meet my needs?

  - by Darth Android

  I'm looking to build a new computer from the ground up. I'm not sure what to look out for and need guidance and help on how to pick the hardware needed to construct my new rig. How do I know what to buy? How do I find out if a given CPU will be enough for a certain game or application that I want to run? How do I find out if a given graphics card will be enough for a certain game or application? What is important when looking at motherboards? How much memory do I need? How do I know how much wattage I need for a power supply? What size case do I need? What relevant standards do I need to read up on and be aware of? PCI, PCIe, SATA, USB 2.0, USB 3.0, etc... What "gotchas" do I need to be on the lookout for? Please keep responses generation-agnostic to ensure they will be helpful to our future users. While Stack Exchange does not permit shopping recommendations, it doesn't provide any general advice to consider when buying hardware. So, instead of just telling those that ask what to buy that it's not allowed, let's tell them how to figure out what they need. This question was Super User Question of the Week #20 Read the June 20, 2011 blog entry for more details or submit your own Question of the Week.

  Read the article

• Diagnosing a BSOD involving USB

  - by David Ebbo

  [Running Win7 Ultimate 64 bit] My new HP Pavilion Elite HPE-450t has been plagued by BSDO crashes since I got it about 5 weeks ago. The crashes are somewhat rare, sometimes not occurring for 3 or 4 days. I have spent a lot of time trying to isolate the device that could be at fault, but I have seen crashes with only the keyboard and mouse plugged in (as USB devices), and I tried two sets of keyboard/mouse, so I'm running out of ideas. :( The WhoCrashed tool gave this info about my latest BSOD: crash dump file: C:\Windows\Minidump\121310-11887-01.dmp This was probably caused by the following module: usbport.sys (USBPORT+0x2DE4E) Bugcheck code: 0xFE (0x5, 0xFFFFFA8008F571A0, 0x80863B34, 0xFFFFFA80092F2510) Error: BUGCODE_USB_DRIVER file path: C:\Windows\system32\drivers\usbport.sys product: Microsoft® Windows® Operating System company: Microsoft Corporation description: USB 1.1 & 2.0 Port Driver Bug check description: This indicates that an error has occurred in a Universal Serial Bus (USB) driver. The crash took place in a standard Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system which cannot be identified at this time. I looked at http://msdn.microsoft.com/en-us/library/ff560407(VS.85).aspx, and for Parameter1 = 0x5, it says "A hardware failure has occurred due to a bad physical address found in a hardware data structure. This is not due to a driver bug". Should I conclude that it's a hardware issue in the machine itself, rather than a bad USB driver or USB device? Here is the MiniDump, in case someone can get more info out of it: http://ewt52q.blu.livefilestore.com/y1peS4Ce8nSK1SXghzMDoxDWXlaEu-EKCJsv25y8y5DXXIUzZ9U0_tYgFJXd939fykwa0zRmx98IW0PYG18GioqKAuARYjtspSA/121310-11887-01.dmp?download&psid=2

  Read the article

• Error - "IR Hardware not detected" - but it's installed/working

  - by Robert

  I am trying to do: Settings-TV-Set up TV signal. During this process I am getting the error "IR Hardware not detected." With the remote, I can select the "try again" button (to re-detect) and it tries again, so the remote works. Plugging in the "IR blaster" doesn't change anything. (I wouldn't expect any difference, but I read a post which said you needed that. I will get Media Center to change channels if I can get that working - but first things first.) I was able to do the setup months ago when I had cable. and everything was fine. I just got DirecTV. (BTW - During the above process, Media Center detects the signal coming in on channel 3. Windows XP Media Center SP3. The TV Tuner card is a Pinnacle TCTV HD PCI. Everything - and I mean everything - has the latest firmware and drivers - as of 4 months ago when I fixed a different problem. So I DON"T WANT TO HEAR the standard answer to check drivers/firmware. THANK YOU.) Thanks for any help.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Performance experiences for running Windows 7 on a Thin-Client?

  - by Peter Bernier

  Has anyone else tried installing Windows 7 on thin-client hardware? I'd be very interested to hear about other people's experiences and what sort of hardware tweaks they had to do to get it to work. (Yes, I realize this is completely unsupported.. half the fun of playing with machines and beta/RC versions is trying out unsupported scenarios. :) ) I managed to get Windows 7 installed on a modified Wyse 9450 Thin-Client and while the performance isn't great, it is usable, particularly as an RDP workstation. Before installing 7, I added another 256Mb of ram (512 total), a 60G laptop hard-drive and a PCI videocard to the 9450 (this was in order to increase the supported screen resolution). I basically did this in order to see whether or not it was possible to get 7 installed on such minimal hardware, and see what the performance would be. For a 550Mhz processor, I was reasonably impressed. I've been using the machine for RDP for the last couple of days and it actually seems slightly snappier than the default Windows XP embedded install (although this is more likely the result of the extra hardware). I'll be running some more tests later on as I'm curious to see particularl whether the streaming video performance will improve. I'd love to hear about anyone's experiences getting 7 to work on extremely low-powered hardware. Particularly any sort of tweaks that you've discovered in order to increase performance..

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >