Search Results

Search found 7606 results on 305 pages for 'raam dev'.

Page 84/305 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• linux: mount old ATA disk to USB adapter

  - by 130490868091234

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic Corp. SL11R-IDE IDE Bridge (04ce:0002), an ATA adapter to USB 1.0 like the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. I get different devices under, for example: /dev/bus/usb/003/002 or /dev/bus/usb/002/004, but I don't get any /dev/sdbN links. The output blkid -o list -c /dev/null is just the laptop's partitions. I have tried taking out the jumper, putting it as master and as CS Enabled, but didn't change the result. Any ideas?

  Read the article

• smartctl short test doesn't seem to complete

  - by Cédric COPY

  I am working on project which involve automated HDD testing through smartctl. The station is working fine on most product, but I have two specific products that fail the smartctl test. Those two product are both WD product (WD2500BUDT series) Smartctl behaviour is quite strange, in fact the test is launched without any problem, i wait about 2min (test length), and when i check the smartctl, i have got no result at all. It's like I hadn't launched any test (no fail, no success in smartctl result). No error return on command, nothing in syslog, .. As i said before, the test is working for other product, thousands products worked well with this test. The main smartctl command used are : smarctl -t shortest /dev/sdX #Launch test smartctl -l selftest /dev/sdX #Look at test result I have tried to use: smartctl -s on /dev/sdX or smartctl -o on /dev/sdX But doesn't change anything. The system is using Debian 6.0, smartctl v5.40 (rev 3124) x86_64, HDD are plug through SATA to PCI controller. I have 4 HDD connected at a time. Well if anyone has some hints to give with this problem, because I have no idea how can i fix this. Thanks in advance. PS: Not sure if it was a serverfault topic, sorry if i was wrong!

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• IPv6 working fine, IPv4 throws OpenSSL error

  - by jippie

  I am building a webserver ( http://blog.linformatronics.nl/ ), which functions just fine on both IPv4 and IPv6 and when using a non-SSL connection. However when I connect to it through https, IPv6 works as expected, but an IPv4 connection throws a client side error. Server side logs are empty for the IPv4/https connection. Summarized in a table: | http | https -----+-------+------------------------------------------------------- IPv4 | works | OpenSSL error, failed. No server side logging. -----+-------+------------------------------------------------------- IPv6 | works | self signed certificate warning, but works as expected Apparently the SSL tunnel isn't even set up, which accounts for the Apache logs being empty. But why does it work fine for IPv6 and fail for IPv4? My question is why is this OpenSSL error being thrown and how can I solve it? Below is some extra information about the setup. IPv6 https Command used to reproduce IPv6/https behaviour: $ wget --no-check-certificate -O /dev/null -6 https://blog.linformatronics.nl --2012-11-03 15:46:48-- https://blog.linformatronics.nl/ Resolving blog.linformatronics.nl (blog.linformatronics.nl)... 2001:980:1b7f:1:a00:27ff:fea6:a2e7 Connecting to blog.linformatronics.nl (blog.linformatronics.nl)|2001:980:1b7f:1:a00:27ff:fea6:a2e7|:443... connected. WARNING: cannot verify blog.linformatronics.nl's certificate, issued by `/CN=localhost': Self-signed certificate encountered. WARNING: certificate common name `localhost' doesn't match requested host name `blog.linformatronics.nl'. HTTP request sent, awaiting response... 200 OK Length: 4556 (4.4K) [text/html] Saving to: `/dev/null' 100%[=======================================================================>] 4,556 --.-K/s in 0s 2012-11-03 15:46:49 (62.5 MB/s) - `/dev/null' saved [4556/4556] IPv4 https Command used to reproduce IPv6/https behaviour: $ wget --no-check-certificate -O /dev/null -4 https://blog.linformatronics.nl --2012-11-03 15:47:28-- https://blog.linformatronics.nl/ Resolving blog.linformatronics.nl (blog.linformatronics.nl)... 82.95.251.247 Connecting to blog.linformatronics.nl (blog.linformatronics.nl)|82.95.251.247|:443... connected. OpenSSL: error:140770FC:SSL routines:SSL23_GET_SERVER_HELLO:unknown protocol Unable to establish SSL connection. Notes I am on Ubuntu Server 12.04.1 LTS

  Read the article

• Routing table on Linux not respected

  - by MRHaarmann

  I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• Poor performance on IIS7, only on Windows Server 2008, fine on Windows 7?

  - by user32005

  Hi, I'm new to IIS7 but have experience with other versions. I've been working on an application that works great in a dev environment (as always) but when I push it to a windows server 2008/IIS7 box performance takes a noticeable hit. The dev environment is Windows7/IIS7. The configuration in IIS is the same on the dev box as the server. I've tried all sorts of things to try and find a reason for this but I cant come to any conclusion. I've ruled out database problems on the live box as all data is cached after the first request. I've confirmed this to be true and made sure there is no additional database traffic. I've ruled out network issues with a combination of monitoring requests with fiddler and local debugging on the server. Whenever the code runs on the server there seems to be a performance issue. The server: Intel Core 2 Quad CPU Q6600 @ 2.40ghz with 2gb RAM. I know this is not fantastic but I was expecting it to at least perform as well as my dev environment (which is running much more on a lower spec). The CPU using peaks at under 60%, and memory usage is less than half of the available. I've enabled failed request tracing and most of the time is spent in a custom HttpModule, this module works to handle every request, I cant get any more detail as to what within the module may be causing the problem. Any ideas, I've been pulling my hair out for days now. Thanks

  Read the article

• Using udev to create a character device based on a driver being loaded

  - by SteveCB

  I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

  Read the article

• Multiple logins with pam_mount means multiple (redundant) mounts ...

  - by Jamie

  I've configured pam_mount.so to automagically mount a cifs share when users login; the problem is if a user logs into multiple times simultaneously, the mount command is repeated multiple times. This so far isn't a problem but it's messy when you look at the output of a mount command. # mount /dev/sda1 on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) //srv1/UserShares/jrisk on /home/jrisk type cifs (rw,mand) //srv1/UserShares/jrisk on /home/jrisk type cifs (rw,mand) //srv1/UserShares/jrisk on /home/jrisk type cifs (rw,mand) I'm assuming I need to fiddle with either the pam.d/common-auth file or pam_mount.conf.xml to accomplish this. How can I instruct pam_mount.so to avoid duplicate mountings?

  Read the article

• Cannot open root device xvda1 or unknown-block(0,0)

  - by svoop

  I'm putting together a Dom0 and three DomU (all Gentoo) with kernel 3.5.7 and Xen 4.1.1. Each Dom has it's own md (md0 for Dom0, md1 for Dom1 etc). Dom0 works fine so far, however, I'm stuck trying to create DomUs. It appears the xvda1 device on DomU is not created or accessible: Parsing config file dom1 domainbuilder: detail: xc_dom_allocate: cmdline="root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3", features="(null)" domainbuilder: detail: xc_dom_kernel_mem: called domainbuilder: detail: xc_dom_boot_xen_init: ver 4.1, caps xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64 domainbuilder: detail: xc_dom_parse_image: called domainbuilder: detail: xc_dom_find_loader: trying multiboot-binary loader ... domainbuilder: detail: loader probe failed domainbuilder: detail: xc_dom_find_loader: trying Linux bzImage loader ... domainbuilder: detail: xc_dom_malloc : 10530 kB domainbuilder: detail: xc_dom_do_gunzip: unzip ok, 0x2f7a4f -> 0xa48888 domainbuilder: detail: loader probe OK xc: detail: elf_parse_binary: phdr: paddr=0x1000000 memsz=0x558000 xc: detail: elf_parse_binary: phdr: paddr=0x1558000 memsz=0x690e8 xc: detail: elf_parse_binary: phdr: paddr=0x15c2000 memsz=0x127c0 xc: detail: elf_parse_binary: phdr: paddr=0x15d5000 memsz=0x533000 xc: detail: elf_parse_binary: memory: 0x1000000 -> 0x1b08000 xc: detail: elf_xen_parse_note: GUEST_OS = "linux" xc: detail: elf_xen_parse_note: GUEST_VERSION = "2.6" xc: detail: elf_xen_parse_note: XEN_VERSION = "xen-3.0" xc: detail: elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 xc: detail: elf_xen_parse_note: ENTRY = 0xffffffff815d5210 xc: detail: elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000 xc: detail: elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" xc: detail: elf_xen_parse_note: PAE_MODE = "yes" xc: detail: elf_xen_parse_note: LOADER = "generic" xc: detail: elf_xen_parse_note: unknown xen elf note (0xd) xc: detail: elf_xen_parse_note: SUSPEND_CANCEL = 0x1 xc: detail: elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 xc: detail: elf_xen_parse_note: PADDR_OFFSET = 0x0 xc: detail: elf_xen_addr_calc_check: addresses: xc: detail: virt_base = 0xffffffff80000000 xc: detail: elf_paddr_offset = 0x0 xc: detail: virt_offset = 0xffffffff80000000 xc: detail: virt_kstart = 0xffffffff81000000 xc: detail: virt_kend = 0xffffffff81b08000 xc: detail: virt_entry = 0xffffffff815d5210 xc: detail: p2m_base = 0xffffffffffffffff domainbuilder: detail: xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff81000000 -> 0xffffffff81b08000 domainbuilder: detail: xc_dom_mem_init: mem 5000 MB, pages 0x138800 pages, 4k each domainbuilder: detail: xc_dom_mem_init: 0x138800 pages domainbuilder: detail: xc_dom_boot_mem_init: called domainbuilder: detail: x86_compat: guest xen-3.0-x86_64, address size 64 domainbuilder: detail: xc_dom_malloc : 10000 kB domainbuilder: detail: xc_dom_build_image: called domainbuilder: detail: xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81b08000 (pfn 0x1000 + 0xb08 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xb08 at 0x7fdec9b85000 xc: detail: elf_load_binary: phdr 0 at 0x0x7fdec9b85000 -> 0x0x7fdeca0dd000 xc: detail: elf_load_binary: phdr 1 at 0x0x7fdeca0dd000 -> 0x0x7fdeca1460e8 xc: detail: elf_load_binary: phdr 2 at 0x0x7fdeca147000 -> 0x0x7fdeca1597c0 xc: detail: elf_load_binary: phdr 3 at 0x0x7fdeca15a000 -> 0x0x7fdeca1cd000 domainbuilder: detail: xc_dom_alloc_segment: phys2mach : 0xffffffff81b08000 -> 0xffffffff824cc000 (pfn 0x1b08 + 0x9c4 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1b08+0x9c4 at 0x7fdec91c1000 domainbuilder: detail: xc_dom_alloc_page : start info : 0xffffffff824cc000 (pfn 0x24cc) domainbuilder: detail: xc_dom_alloc_page : xenstore : 0xffffffff824cd000 (pfn 0x24cd) domainbuilder: detail: xc_dom_alloc_page : console : 0xffffffff824ce000 (pfn 0x24ce) domainbuilder: detail: nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) domainbuilder: detail: xc_dom_alloc_segment: page tables : 0xffffffff824cf000 -> 0xffffffff824e6000 (pfn 0x24cf + 0x17 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cf+0x17 at 0x7fdece676000 domainbuilder: detail: xc_dom_alloc_page : boot stack : 0xffffffff824e6000 (pfn 0x24e6) domainbuilder: detail: xc_dom_build_image : virt_alloc_end : 0xffffffff824e7000 domainbuilder: detail: xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 domainbuilder: detail: xc_dom_boot_image: called domainbuilder: detail: arch_setup_bootearly: doing nothing domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32 domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_64 domainbuilder: detail: xc_dom_update_guest_p2m: dst 64bit, pages 0x138800 domainbuilder: detail: clear_page: pfn 0x24ce, mfn 0x37ddee domainbuilder: detail: clear_page: pfn 0x24cd, mfn 0x37ddef domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cc+0x1 at 0x7fdece675000 domainbuilder: detail: start_info_x86_64: called domainbuilder: detail: setup_hypercall_page: vaddr=0xffffffff81001000 pfn=0x1001 domainbuilder: detail: domain builder memory footprint domainbuilder: detail: allocated domainbuilder: detail: malloc : 20658 kB domainbuilder: detail: anon mmap : 0 bytes domainbuilder: detail: mapped domainbuilder: detail: file mmap : 0 bytes domainbuilder: detail: domU mmap : 21392 kB domainbuilder: detail: arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xbaa6f domainbuilder: detail: shared_info_x86_64: called domainbuilder: detail: vcpu_x86_64: called domainbuilder: detail: vcpu_x86_64: cr3: pfn 0x24cf mfn 0x37dded domainbuilder: detail: launch_vm: called, ctxt=0x7fff224e4ea0 domainbuilder: detail: xc_dom_release: called Daemon running with PID 4639 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.7-gentoo (root@majordomo) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #1 SMP Tue Nov 20 10:49:51 CET 2012 [ 0.000000] Command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] Xen: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000138ffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] MPS support code is not built-in. [ 0.000000] Using acpi=off or acpi=noirq or pci=noacpi may have problem [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x139000 max_arch_pfn = 0x400000000 [ 0.000000] e820: last_pfn = 0x100000 max_arch_pfn = 0x400000000 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xffffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x138ffffff] [ 0.000000] NUMA turned off [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000138ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x138ffffff] [ 0.000000] NODE_DATA [mem 0x1387fc000-0x1387fffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x138ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009ffff] [ 0.000000] node 0: [mem 0x00100000-0x138ffffff] [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] e820: cannot find a gap in the 32bit address range [ 0.000000] e820: PCI devices with unassigned 32bit BARs may break! [ 0.000000] e820: [mem 0x139100000-0x1394fffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.1 (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880138400000 s75712 r8192 d22592 u2097152 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1259871 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4943980k/5128192k available (3937k kernel code, 448k absent, 183764k reserved, 1951k data, 524k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3411.602 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6823.20 BogoMIPS (lpj=3411602) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.001355] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002974] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003441] Mount-cache hash table entries: 256 [ 0.003595] Initializing cgroup subsys cpuacct [ 0.003599] Initializing cgroup subsys freezer [ 0.003637] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.003637] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.003643] CPU: Physical Processor ID: 0 [ 0.003645] CPU: Processor Core ID: 0 [ 0.003702] SMP alternatives: switching to UP code [ 0.011791] Freeing SMP alternatives: 12k freed [ 0.011835] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.011886] Brought up 1 CPUs [ 0.011998] Grant tables using version 2 layout. [ 0.012009] Grant table initialized [ 0.012034] NET: Registered protocol family 16 [ 0.012328] PCI: setting up Xen PCI frontend stub [ 0.015089] bio: create slab <bio-0> at 0 [ 0.015158] ACPI: Interpreter disabled. [ 0.015180] xen/balloon: Initialising balloon driver. [ 0.015180] xen-balloon: Initialising balloon driver. [ 0.015180] vgaarb: loaded [ 0.016126] SCSI subsystem initialized [ 0.016314] PCI: System does not support PCI [ 0.016320] PCI: System does not support PCI [ 0.016435] NetLabel: Initializing [ 0.016438] NetLabel: domain hash size = 128 [ 0.016440] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.016447] NetLabel: unlabeled traffic allowed by default [ 0.016475] Switching to clocksource xen [ 0.017434] pnp: PnP ACPI: disabled [ 0.017501] NET: Registered protocol family 2 [ 0.017864] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.019322] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.020376] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.020497] TCP: Hash tables configured (established 524288 bind 65536) [ 0.020500] TCP: reno registered [ 0.020525] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020564] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020624] NET: Registered protocol family 1 [ 0.020658] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.020662] software IO TLB [mem 0xfb632000-0xff631fff] (64MB) mapped at [ffff8800fb632000-ffff8800ff631fff] [ 0.020750] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.021378] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.023378] msgmni has been set to 9656 [ 0.023544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.023549] io scheduler noop registered [ 0.023551] io scheduler deadline registered [ 0.023580] io scheduler cfq registered (default) [ 0.023650] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.023845] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.024082] Non-volatile memory driver v1.3 [ 0.024085] Linux agpgart interface v0.103 [ 0.024207] Event-channel device installed. [ 0.024265] [drm] Initialized drm 1.1.0 20060810 [ 0.024268] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.025145] brd: module loaded [ 0.025565] loop: module loaded [ 0.045646] Initialising Xen virtual ethernet driver. [ 0.198264] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.199096] i8042: No controller found [ 0.199139] mousedev: PS/2 mouse device common for all mice [ 0.259303] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.259353] rtc_cmos: probe of rtc_cmos failed with error -38 [ 0.259440] md: raid1 personality registered for level 1 [ 0.259542] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 0.259732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.259747] TCP: cubic registered [ 0.259886] NET: Registered protocol family 10 [ 0.260031] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.260070] sit: IPv6 over IPv4 tunneling driver [ 0.260194] NET: Registered protocol family 17 [ 0.260213] Bridge firewalling registered [ 5.360075] XENBUS: Waiting for devices to initialise: 25s...20s...15s...10s...5s...0s...235s...230s...225s...220s...215s...210s...205s...200s...195s...190s...185s...180s...175s...170s...165s...160s...155s...150s...145s...140s...135s...130s...125s...120s...115s...110s...105s...100s...95s...90s...85s...80s...75s...70s...65s...60s...55s...50s...45s...40s...35s...30s...25s...20s...15s...10s...5s...0s... [ 270.360180] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) [ 270.360273] md: Waiting for all devices to be available before autodetect [ 270.360277] md: If you don't use raid, use raid=noautodetect [ 270.360388] md: Autodetecting RAID arrays. [ 270.360392] md: Scanned 0 and added 0 devices. [ 270.360394] md: autorun ... [ 270.360395] md: ... autorun DONE. [ 270.360431] VFS: Cannot open root device "xvda1" or unknown-block(0,0): error -6 [ 270.360435] Please append a correct "root=" boot option; here are the available partitions: [ 270.360440] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 270.360444] Pid: 1, comm: swapper/0 Not tainted 3.5.7-gentoo #1 [ 270.360446] Call Trace: [ 270.360454] [<ffffffff813d2205>] ? panic+0xbe/0x1c5 [ 270.360459] [<ffffffff813d2358>] ? printk+0x4c/0x51 [ 270.360464] [<ffffffff815d5fb7>] ? mount_block_root+0x24f/0x26d [ 270.360469] [<ffffffff815d62b6>] ? prepare_namespace+0x168/0x192 [ 270.360474] [<ffffffff815d5ca7>] ? kernel_init+0x1b0/0x1c2 [ 270.360477] [<ffffffff815d5500>] ? loglevel+0x34/0x34 [ 270.360482] [<ffffffff813d5a64>] ? kernel_thread_helper+0x4/0x10 [ 270.360486] [<ffffffff813d4038>] ? retint_restore_args+0x5/0x6 [ 270.360490] [<ffffffff813d5a60>] ? gs_change+0x13/0x13 The config: name = "dom1" bootloader = "/usr/bin/pygrub" root = "/dev/xvda1 ro" extra = "3" # runlevel memory = 5000 disk = [ 'phy:/dev/md1,xvda1,w' ] # vif = [ 'ip=..., vifname=veth1' ] # none for now Here are some details on the Dom0 kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y # CONFIG_XEN_BLKDEV_FRONTEND is not set CONFIG_XEN_BLKDEV_BACKEND=y # CONFIG_XEN_NETDEV_FRONTEND is not set CONFIG_XEN_NETDEV_BACKEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PCIDEV_BACKEND=m CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m And the DomU kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y CONFIG_XEN_BLKDEV_FRONTEND=y CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y # CONFIG_XEN_BACKEND is not set CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m Any ideas what I'm doing wrong here? Thanks a lot!

  Read the article

• Instructions to setup primary and only domain controller

  - by Robert Koritnik

  Where could I get best step by step instructions (with some simple explanations) how to setup domain controller on Windows Server 2008 R2 Server Core? I don't know what do I need? Do I need DNS as well and AD and so on and so forth. I don't know enough about these things, but I need to set them up to prepare development environment. I would also like to know how to configure firewall on DC machine, to make it visible on other machines because I've setup DC somehow but I can't connect to it... This is my HW config: Linksys internet router with DHCP my dev machine is Windows 7 my DC machine is a VM in my dev machine my dev machine has a hw network adapter to linksys and a virtual network adapter to DC DC machine has two network adapters: one to linksys (to be internet connected so it can be updated etc.) and one to host (my dev Win7 machine) Edit My development machine should access domain controller and logon using domain credentials. Development machine would access internet directly via Linksys router. My domain controller machine would only serve authentication (and if I'm able to configure it right) should also have Active Directory Federation Services in a workable condition. I hope this is a bit more clear now. At least a small bit.

  Read the article

• IP routing Solaris 9 access the internet from local network

  - by help_me

  I am trying to configure the NICS on the Solaris Sparc server. My problem lies in getting out to the "Internet" from the local network. I have requested the NIC to receive a DHCP server address #ifconfig -interface dhcp start. If anyone could guide me as to what I need to do next. I am not able to ping 4.2.2.2 or access the internet. Much appreciated, thank you #uname -a SunOS dev 5.9 Generic_122300-59 sun4u sparc SUNW,Sun-Fire-V210 ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.3 netmask ffffc000 broadcast 10.100.63.255 bge0:2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.22 netmask ffffc000 broadcast 10.100.63.255 bge3: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 12 inet 169.14.60.37 netmask fffffe00 broadcast 169.14.61.255 cat /etc/defaultrouter 10.100.0.254 169.14.60.1 cat /etc/resolv.conf nameserver 169.14.96.73 nameserver 169.10.8.4 netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 169.14.60.37 169.14.60.1 UGH 1 0 169.14.60.0 169.14.60.37 U 1 18 bge3 10.100.0.0 10.100.0.3 U 1 34940 bge0 10.100.0.0 10.100.0.22 U 1 0 bge0:2 224.0.0.0 10.100.0.3 U 1 0 bge0 default 10.100.0.254 UG 1 111 default 169.14.60.1 UG 1 26 127.0.0.1 127.0.0.1 UH 10 59464 lo0 bash-2.05$ sudo ndd -get /dev/ip bge0:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip bge3:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip ip_forwarding 1

  Read the article

• SWATCH - what am I doing wrong?

  - by Brian Dunbar

  What I want/need/desire is to log when a user logs into my FTP server. Problem: I can't make swatch work the way I should be able to. This data is logged to a file - but of course these logs are not kept very long. I can't keep the logs around forever, but I can extract data from then, analyze it, store results elsewhere. If there is a better way to do this than the following, I'm all ears. Swatch version 3.2.3 Perl 5.12 FTP: VSFTP OS (Test): OS X 10.6.8 OS (Production): Solaris From man I see I can pass contents to a command .. so I should be able to echo those values to file, do a sed/cut/uniq thing on them for stats. $ man swatch (snip) exec command Execute command. The command may contain variables which are substituted with fields from the matched line. A $N will be replaced by the Nth field in the line. A $0 or $* will be replaced by the entire line. Swatch file .swatchrc watchfor /OK LOGIN/ echo=red pipe "echo "0: $0 1:$1 2:$2 3:$3 4:$4 5:$5" >> /Users/bdunbar/dev/ftplog/output.txt" Launch with $ swatch -c /Users/bdunbar/.swatchrc --script-dir /Users/bdunbar/dev/ftplog -t /Users/bdunbar/dev/ftplog/vsftpd.log & Test echo "Mon July 9 03:11:07 2012 [pid 14938] [aetech] OK LOGIN: Client "206.209.255.227"" >> vsftpd.log Results - it's echoing to TTY. This is not needed or desired on the server, but it does tell me things are working. ftplog *** swatch version 3.2.3 (pid:25780) started at Mon Jul 9 15:23:33 CDT 2012 Mon July 9 03:11:07 2012 [pid 14938] [aetech] OK LOGIN: Client 206.209.255.227 Results - bad! I appear to not be sending the variables to text. $ tail -f output.txt 0: /Users/bdunbar/dev/ftplog/.swatch_script.25780 1: 2: 3: 4: 5:

  Read the article

• How to change mount to grant user write permissions?

  - by nals

  I am on TomatoUSB, and using the feature to have a NAS. The only way I can write to the Samba share is if I force root: [global] interfaces = 127.0.0.1, 192.168.1.1/24 bind interfaces only = no workgroup = WORKGROUP netbios name = TOMATO security = share wins support = yes name resolve order = wins lmhosts hosts bcast guest account = nobody [Public] path = /mnt/sda2 read only = no public = yes only guest = yes guest ok = yes browseable = yes comment = Network share force user = root writeable = yes I dont really like the idea having to use root to allow write access to my share. I have a samba account created already named nobody to allow access to the share. However every time I try to write I get access denied error. fstab: /dev/sda2 /mnt/sda2 vfat defaults 0 0 Further more every time I try to chmod 777 /tmp/mnt/sda2 the permissions are not changed, and no error is produced. They stay 755. drwxr-xr-x 2 root root 4096 Jun 4 01:49 sda2 Basically; how can I give the user nobody write permissions to my mount? dev name: /dev/sda2 dev mount: /tmp/mnt/sda2

  Read the article

• kill a hung mount process

  - by John P

  I have a virtual machine drive that ran out of space, so I shutdown the VM, extended the volume using lvextend. After resizing the partition (ext3), I ran e2fsck on it, and it found and corrected errors. Unfortunately, when I ran efsck one more time, there were more errors that had to be fixed. I went through 3 rounds of e2fsck before I decided to try mounting it to clean up some space manually. I tried mounting it, but the mount process hung. I tried to "kill -9" the mount process, but that did not kill it. I killed the parent process, but that did not kill it either. Any ideas on how to kill a rogue mount process? Some evidence: ps -l 13292 F S UID PID PPID C PRI NI ADDR SZ WCHAN TTY TIME CMD 4 R 0 13292 1 99 85 0 - 17964 - ? 11:27 mount /dev/mapper/xen7-123p3 /tmp/p3/ lsof -p 13292 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME mount 13292 root cwd DIR 9,2 4096 25264129 /root mount 13292 root rtd DIR 9,2 4096 2 / mount 13292 root txt REG 9,2 61656 2916434 /bin/mount mount 13292 root mem REG 9,2 144776 31457282 /lib64/ld-2.5.so mount 13292 root mem REG 9,2 1718232 31457284 /lib64/libc-2.5.so mount 13292 root mem REG 9,2 23360 31457291 /lib64/libdl-2.5.so mount 13292 root mem REG 9,2 43808 31457783 /lib64/libblkid.so.1.0 mount 13292 root mem REG 9,2 247496 31457331 /lib64/libsepol.so.1 mount 13292 root mem REG 9,2 95464 31457337 /lib64/libselinux.so.1 mount 13292 root mem REG 9,2 154640 31457491 /lib64/libdevmapper.so.1.02 mount 13292 root mem REG 9,2 17936 31457472 /lib64/libuuid.so.1.2 mount 13292 root mem REG 9,2 56438208 12684878 /usr/lib/locale/locale-archive mount 13292 root 0u CHR 136,11 0t0 13 /dev/pts/11 (deleted) mount 13292 root 1u CHR 136,11 0t0 13 /dev/pts/11 (deleted) mount 13292 root 2u CHR 136,11 0t0 13 /dev/pts/11 (deleted) umount -f /tmp/p3/ umount2: Invalid argument umount: /tmp/p3/: not mounted

  Read the article

• Advertise a subnet route with radvd

  - by Thomas Berger

  we have set up a small IPv6 Testing network. The setup looks like this: ::/0 +----------+ | Firewall | Router to the public net +----------+ | 2001:...::/106 | +----------+ +-------| SIT GW | sit Tunnel gatway to the some test users | +----------+ | +----------+ | Test Sys | Testsystem +----------+ The idea is to advertise the default route from the firewall and the route for the SIT subnets from the sit gateway. The configurations for radvd are: # Firewall interface eth0 { AdvSendAdvert on; route ::/0 { }; }; # SIT Gatway interface eth0 { AdvSendAdvert on; route 2001:...::/106 { }; }; We have captured the adv. packages with tcpdump and the packages looks good. We see a default route from the fw, and the subnet route from the SIT gatway. But if we look on the testsystem there are two default routes over both gateways. There is no subnet route. The routing does not work of course. Here the routes we get: 2001:.....::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::baac:6fff:fe8e:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 default via fe80::e415:aeff:fe12:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 Any Idea?

  Read the article

• tc u32 --- how to match L2 protocols in recent kernels?

  - by brownian

  I have a nice shaper, with hashed filtering, built at a linux bridge. In short, br0 connects external and internal physical interfaces, VLAN tagged packets are bridged "transparently" (I mean, no VLAN interfaces are there). Now, different kernels do it differently. I can be wrong with exact kernel verions ranges, please forgive me. Thanks. 2.6.26 So, in debian, 2.6.26 and up (up to 2.6.32, I believe) --- this works: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 flowid 1:200 Here, "kernel" matches two bytes in "protocol" field with 0x8100, but counts the beginning of ip packet as a "zero position" (sorry for my English, if I'm a bit unclear). 2.6.32 Again, in debian (I've not built vanilla kernel), 2.6.32-5 --- this works: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 at 20 flowid 1:200 Here, "kernel" matches the same for protocol, but counts offset from the beginning of this protocol's header --- I have to add 4 bytes to offset (20, not 16 for dst address). It's ok, seems more logical, as for me. 3.2.11, the latest stable now This works --- as if there is no 802.1q tag at all: tc filter add dev internal protocol ip parent 1:0 prio 100 \ u32 ht 1:64 match ip dst 192.168.1.100 flowid 1:200 The problem is that I couldn't find a way to match 802.1q tag so far. Matching 802.1q tag at past I could do this before as follows: tc filter add dev internal protocol 802.1q parent 1:0 prio 100 \ u32 match u16 0x0ed8 0x0fff at -4 flowid 1:300 Now I'm unable to match 802.1q tag with at 0, at -2, at -4, at -6 or like that. The main issue that I have zero hits count --- this filter is not being checked at all, "wrong protocol", in other words. Please, anyone, help me :-) Thanks!

  Read the article

• On linux, what does it mean when a directory has size 0 instead of 4096?

  - by kdt

  Here's a strange thing I haven't seen before -- a directory whose size is reported by ls as 0 instead of 4096, and I can't create any files within it. # ls -ld lib home drwxr-xr-x. 2 root root 0 Feb 7 03:10 home <-- it has zero size dr-xr-xr-x. 11 root root 4096 Feb 4 09:28 lib # touch home/foo touch: cannot touch `home/foo': No such file or directory <-- and I can't create files in it # rm home rm: cannot remove `home': Is a directory <-- look, it really is a dir So what does it mean for a directory to have size 0 instead of 4096? Filesystem is ext4 on fedora core 14. The output of mount is: /dev/mapper/vg_dev-lv_root on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw,rootcontext="system_u:object_r:tmpfs_t:s0") /dev/vda1 on /boot type ext4 (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) Output of du -s /home: 0 /home Output of stat /home: File: `/home' Size: 0 Blocks: 0 IO Block: 1024 directory Device: 15h/21d Inode: 34913 Links: 2 Access: (0755/drwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2011-02-07 03:45:46.188995765 -0800 Modify: 2011-02-07 03:11:59.980995019 -0800 Change: 2011-02-06 07:58:45.874995002 -0800

  Read the article

• Recovering ZFS pool with errors on import.

  - by Sqeaky

  I have a machine that had some trouble with some bad RAM. After I diagnosed it and removed the offending stick of RAM, The ZFS pool in the machine was trying to access drives by using incorrect device names. I simply exported the pool and re-imported it to correct this. However I am now getting this error. The pool Storage no longer automatically mounts sqeaky@sqeaky-media-server:/$ sudo zpool status no pools available A regular import says its corrupt sqeaky@sqeaky-media-server:/$ sudo zpool import pool: Storage id: 13247750448079582452 state: UNAVAIL status: The pool is formatted using an older on-disk version. action: The pool cannot be imported due to damaged devices or data. config: Storage UNAVAIL insufficient replicas raidz1 UNAVAIL corrupted data 805066522130738790 ONLINE sdd3 ONLINE sda3 ONLINE sdc ONLINE A specific import says the vdev configuration is invalid sqeaky@sqeaky-media-server:/$ sudo zpool import Storage cannot import 'Storage': invalid vdev configuration I should have 4 devices in my ZFS pool: /dev/sda3 /dev/sdd3 /dev/sdc /dev/sdb I have no clue what 805066522130738790 is but I plan on investigating further. I am also trying to figure out how to use zdb to get more information about what the pool thinks is going on. For reference This was setup this way, because at the time this machine/pool was setup it needed certain Linux features and booting from ZFS wasn't yet supported in Linux. The partitions sda1 and sdd1 are in a raid 1 for the operating system and sdd2 and sda2 are in a raid1 for the swap. Any clue on how to recover this ZFS pool?

  Read the article

• Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• How can I use an own asp page as 404 error page on a Windows 7 pro IIS 7.5 local installation

  - by Edelcom

  Running Windows 7 Pro Running local IIS 7.5 ( for web development purposes ) Edited hosts file to be able to use http://www.sitestepper.dev Site build in subfolder of the inetpub/wwwroot/staplijst Site can be viewed using http://www.sitestepper.dev/staplijst/whatever-page.htm I have an http://www.sitestepper.dev/p.asp page I would like to call when an unknown page is requested. This technique works fine on the deployed version of this web site ( deployed on an Windows 2003 server running IIS 7 - not sure about the 7 but it is the version deployed with Windows 2003 server ). I tried ( in the Edit Custom Error Dialog ) : Execute a URL on this site: with value /staplijst/p.asp and Respond with a 302 redirect: with value http://www.sitestepper.dev/staplijst/p.asp I tried this in the properties of the 'Default Web Site' , and I tried this at the staplijst level. Even tried it with values without the /staplijst. I restarted the default web site after each change. And even stopped/started the Web service. But nothing seems to work, I keep getting the 'Server Error In Application "DEFAULT WEB SITE"' , HTTP Error 404.0 error. What am I missing here - probably something obvious, but I don't see it ? Thanks in advance

  Read the article

• Change source address based on destination IP

  - by hgj

  We have several "router" machines that gather a lot of external IP addresses on the same host and redirect, NAT or proxy the traffic to the internal network. They also act as routers for the machines on the internal network. This works fine, however I am unable to make the routing table, so I can change the source address, based on the destination a machine from the internal network want to access. Let's say I have a router, that has public addresses P1 (5.5.5.1/24) and P2 (5.5.5.2/24). All traffic goes through P1, but if necessary, the host is reachable on P2 too. This looks like this and works fine: > ip addr ... 1: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether aa:bb:cc:dd:ee:11 brd ff:ff:ff:ff:ff:ff inet 5.5.5.1/24 brd 5.5.5.255 scope global eth1 inet 5.5.5.2/24 brd 5.5.5.255 scope global secondary eth1:p2 ... Now I want to use P2 as the source address, if I want to access the Google DNS service for example (8.8.8.8). So I add a row in the routing table like: > ip route add 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 > ip route ... default via 5.5.5.254 dev eth1 5.5.5.0/24 dev eth1 proto kernel scope link src 5.5.5.1 8.8.8.8 via 5.5.5.254 dev eth1 src 5.5.5.2 ... But this does not work. If I ping 8.8.8.8, the host still uses P1 as the source address, and does not use P2 at all for outgoing connections. Am I doing it right? I guess not...

  Read the article

• Configuring PAM with pam_mount; getting a dlopen() with an HX_Init error

  - by Jamie

  I'm trying to get automounting upon login working on Ubuntu 10.03 Beta 2. I didn't find a package for pam_mount, so I ended downloading it and building it. This required: sudo apt-get install build-essential pkg-config libxml2-dev libssl-dev libpam-dev Additionally, the libHX-dev is required but as of yesterday (23/4/2010) the package version provided (3.2) wasn't up to snuff (3.4) so I downloaded, compiled and installed that too. cd ./pam_mount-1.36/ && ./configure && make && sudo make install When I tried it (pam_mount) I got this in my auth log: Apr 23 12:18:02 ubuntu sshd[1195]: PAM unable to dlopen(/lib/security/pam_mount.so): /lib/security/pam_mount.so: undefined symbol: HX_init Apr 23 12:18:02 ubuntu sshd[1195]: PAM adding faulty module: /lib/security/pam_mount.so Apr 23 12:18:06 ubuntu sshd[1195]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=192.168.20.182 user=jrisk Apr 23 12:18:06 ubuntu sshd[1195]: pam_winbind(sshd:auth): getting password (0x00000388) Apr 23 12:18:06 ubuntu sshd[1195]: pam_winbind(sshd:auth): pam_get_item returned a password Apr 23 12:18:06 ubuntu sshd[1195]: pam_winbind(sshd:auth): user 'jrisk' granted access Apr 23 12:18:06 ubuntu sshd[1195]: Accepted password for jrisk from 192.168.20.182 port 4369 ssh2 Apr 23 12:18:06 ubuntu sshd[1195]: pam_unix(sshd:session): session opened for user jrisk by (uid=0) What do I need to do get HX_Init into the system? This is related to an answer I previously got here.

  Read the article

• Relayout LVM Disk

  - by Tom

  I have an Ubuntu 11.10 system with two 500GB disks. The partition tables look like this: /dev/sda1 primary 465.52GB /dev/sda2 extended 243.17MB -> /dev/sda5 logical 243.14MB /dev/sdb1 primary 465.76GB sda1 and sdb1 are in a single LVM physical volume group containing a single logical volume containing a single logical filesystem which is mounted as /. sda5 is mounted as /boot. The problem comes when I want to upgrade to Ubuntu 12.04, which requires at least 247MB free on /boot. So I need to reduce the size of sda1 so that I can increase the size of sda2 and sda5. How the heck do I do that? I can find how to shrink the logical volume group, but I'm not at all clear on how to clear out the end part of sda1 so that I can reduce the physical volume group. Does pvresize just deal with this automagically? Or is that wild wishful thinking? I guess the alternatives are to back everything up onto something or other and recreate the thing from scratch or find out whether GRUB2 supports using LVM for /boot.

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >