Search Results

Search found 7126 results on 286 pages for 'wireless router'.

Page 84/286 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

  • Using Synology NAS attached to WDS-Repeater

    - by Kai B
    I'm using the following devices for my home network: Router 1: Speedport W 723 V (192.168.2.1) Router 2: AVM Fritzbox 3270 (192.168.2.2) NAS: Synology DS 207+(192.168.2.3) I successfully set up a WDS connection between the two routers. The Speedport acts as basestation, the Fritzbox repeats the WIFI signal of the Speedport. Everything fine, so far. Now I'm trying to achieve the following: Client → Speedport (Base) → Fritzbox (Repeater) → Synology NAS I want to use my Synology NAS attached to the Fritzbox (which is in repeating mode). I already gave it a static IP (as written above) but all connection attempts failed. Did I miss something out or is this set-up simply impossible?

    Read the article

  • WRT54G - how use port forwarding and VNC

    - by unknown (yahoo)
    Since I have my home network behind a WRT54G, the router has an external "real" IP address, and the PCs behind it have 192.168.xxx.xxx addresses. I would like to be able to control one of them remotely - preferably using UltraVNC, but I am open to suggestions. Since I can't directly address that PC from the internet, I figured I could address a port on my router and have the traffic forwarded to the PC (and the same in the reverse direction). Is that feasible? Can anyone tell me how to do it (or point me to an URL that does)? Thanks

    Read the article

  • Migrating from DD-WRT to Tomato

    - by Collin Allen
    Is it possible to switch to the latest version of Tomato on a router that's already running DD-WRT? Using the default Linksys firmware on my WRT54GL v1.1, I had to upload a micro version of DD-WRT first. I imagine that, since I'm now running third-party firmware, I won't have to do that again to make the switch, but I thought I should check so as not to brick it. This router is taking a back seat to a new AirPort Extreme (for the 'n' capability), but I still want to have the soon-to-be-Tomato device sit between the AirPort Extreme and my modem for the superior traffic graphing.

    Read the article

  • How do I set up a public server on a network?

    - by tyjkenn
    I am trying to set up a personal cloud server with OwnCloud on Ubuntu. LAMP is all set up. I was able to access it using the external IP address when I connected it directly to the modem, but what if I what if I want my server to share a LAN? I still want it accessible over the internet, but then if I go to the IP address from a web browser, it just tries to log into to router admin tools. The internal IP address works across the LAN, but I want to be able to access it from anywhere. This may be simple and I may be over-thinking it, but how do access my server? The router I am using is ASUS WL-520GU.

    Read the article

  • ADSL Modem Goes Slower Than Dialup

    - by peter
    Hi All, I have two ADSL modems, the first one does not have wireless, but is configured and working fine at around 6 - 7 mbps (ADSL) on Orcon in New Zealand. I bought a Belkin N150 wireless router to replace the first one. I configured it exactly the same as the first one, but a speed test confirms that it is running slower than dial up. One difference I noticed is that the first modem (a linksys) came from Orcon, and didn't have an ADSL username and password set up. The Belkin modem on the other hand wouldn't let me leave the username and password field blank. Any ideas? I am a techy guy, so it doesn't appear to be anything obvious with the settings I have missed. Thanks.

    Read the article

  • Setup LAN to serve webpages and voip and access to the web site from inside LAN with domain name

    - by Mauricio Arias
    I'd like to know if it will work: I have my domain and I´m serving a webpage in a nginx to the internet, but if I type my domain in my laptop inside LAN I access to my modem/router configuration, I cannot access to the web server unless I type the IP address. I would like to add a Bind server after the modem/router - (port forward, ports 80 and 5060), if the request is www.mydomain.com bind should resolve the nginx IP address and serve it, and if it is a voip request should address to the voip server and if I'd like to access to the website from inside LAN I'd like to type mydomain.com. Could I do it with this configuration? Do I need something else? Thanks in advace!

    Read the article

  • Cisco 877 as a VPN server?

    - by Massimo
    I have a Cisco 877 router which connects my network to the Internet using an ADSL line, a single public IP address and NAT; the IOS version is 15. Everything is working ok, but I'd like to configure this router to be a VPN server, to be able to connect to the network from the outside. I've tried looking for documentation, but everything I can find is related to having the 877 act as a VPN client, or to site-to-site VPNs; I can't find anything about letting single remote computers access the internal network, which is something I can do quite easily using Windows' RRAS or ISA Server. Can the Cisco 877 act as a VPN server for remote client computers? (Looks like it should, but just to be sure...) Which type of VPNs does it support? Do they require some special software on the client machines, or can they be used by standard out-of-the-box Windows computers? And, finally: how to set up this?

    Read the article

  • DNS Server and Private HTTP / SOCKS Proxy

    - by DucDigital
    Hi every one, this is just a small hacking attemp to our router. I'm trying to setup a small DNS and forward webpages through proxy behind the scene. I've successfully implement the DNS server that will do the resolving or anything involved in address resolve. But is there anyway I can forward the user using DNS to a proxy instead of request directly to the server? Are there any software/opensource that I can use? I notice on paid wireless, they can provide a login page if user is not login yet, i think this is a way of implementing proxy. Also the hardware is very basic with linksys and netgear router which connect directly to the internet. It's a basic LAN

    Read the article

  • DNS Server and Private HTTP / SOCKS Proxy

    - by DucDigital
    Hi every one, this is just a small hacking attemp to our router. I'm trying to setup a small DNS and forward webpages through proxy behind the scene. I've successfully implement the DNS server that will do the resolving or anything involved in address resolve. But is there anyway I can forward the user using DNS to a proxy instead of request directly to the server? Are there any software/opensource that I can use? I notice on paid wireless, they can provide a login page if user is not login yet, i think this is a way of implementing proxy. Also the hardware is very basic with linksys and netgear router which connect directly to the internet. It's a basic LAN

    Read the article

  • USR9108 not connecting to DSL service/not detecting carrier

    - by Salman A
    As suggested in this answer I've hooked up the phone cable to the USR9108 router. I've entered the information provided by the ISP (VPI/VCI, Username, Password etc) in the ADSL configuration section but the router does not connect to DSL service. The ASDL diagnostics fail in the first step stating that no signal was found. The same phone line when connected to ZyXEL P-660R-T1 v2 modem works successfully. Can anyone tell me how to trouble shoot this issue? Does it have something to do with 2 wire and 4 wire telephone line? PS: whats the difference between ASDL and DSL?

    Read the article

  • ADSL Modem Goes Slower Than Dialup

    - by peter
    Hi All, I have two ADSL modems, the first one does not have wireless, but is configured and working fine at around 6 - 7 mbps (ADSL) on Orcon in New Zealand. I bought a Belkin N150 wireless router to replace the first one. I configured it exactly the same as the first one, but a speed test confirms that it is running slower than dial up. One difference I noticed is that the first modem (a linksys) came from Orcon, and didn't have an ADSL username and password set up. The Belkin modem on the other hand wouldn't let me leave the username and password field blank. Any ideas? I am a techy guy, so it doesn't appear to be anything obvious with the settings I have missed. Thanks.

    Read the article

  • Assigning static IP and domain name mapping to local server in LAN

    - by yashbinani
    I have developed a web application which will be deployed in a LAN environemnt. Clients will be Computers/Android Tablets/IPAD In order for communication between client and local server 1) need to assign a static IP to local server. 2) need a domian name mapping for that IP address in Local environment. 3) router should assign the same static IP if it gets restarted etc. I am using a windows XP machine as Local server OS. Do i need to take care of router configurations before buying one, or all routers will have same capability to perform this task. I am not a network specialist, so Sorry if this question sounds stupid. Thanks

    Read the article

  • pfSense 2.1 OpenVPN client not using tunnelled interface

    - by Brian M. Hunt
    I'm having some trouble getting OpenVPN working on my pfSense box. The issue is quite strange to me. When I have the OpenVPN turned on, only my router is able to connect to the Internet. From the router I can use ping, links, etc., and connections work exactly as expected - through the VPN, with the IP address assigned by my VPN provider (Proxy.sh, incidentally). However, none of the clients on the local network can connect to the Internet. I get timeouts when using ping or a web browser. I can ping my router, and the IP address of the gateway. When I switch the default gateway from the VPN to my ISP's gateway, all works exactly as expected. Here the routing table (netstat -r) when in VPN mode, and a key for it: IPv4 Destination Gateway Flags Refs Use Mtu Netif Expire 0.0.0.0/1 10.XX.X.53 UGS 0 122 1500 ovpnc1 = default 10.XX.X.53 UGS 0 235 1500 ovpnc1 8.8.8.8 10.XX.X.53 UGHS 0 82 1500 ovpnc1 10.XX.X.1/32 10.11.0.53 UGS 0 0 1500 ovpnc1 10.XX.X.53 link#12 UH 0 0 1500 ovpnc1 10.XX.X.54 link#12 UHS 0 0 16384 lo0 ZZ.XX.XXX.0/20 link#1 U 0 83 1500 re0 ZZ.XX.XXX.XXX link#1 UHS 0 0 16384 lo0 127.0.0.1 link#9 UH 0 12 16384 lo0 128.0.0.0/1 10.11.0.53 UGS 0 123 1500 ovpnc1 192.168.1.0/24 link#11 U 0 1434 1500 ue0 192.168.1.1 link#11 UHS 0 0 16384 lo0 YYY.YYY.YYY.YYY/32 ZZ.XX.XXX.1 UGS 0 249 1500 re0 IP addresses 10.XX.X.53/54 - My DHCP-assigned IP address/pair from the VPN provider ZZ.XX.XXX.XXX - My external IP assigned by my ISP YYY.YYY.YYY.YYY - The external IP assigned by the VPN provider Interfaces ovpnc1 - My VPN client interface re0 - My LAN interface ue0 - My WAN interface This looks essentially what I would expect it to be. The default route is through the VPN provider. The VPN address is routed through the ISP-assigned IP address. I am not sure what would be wrong here. So figuring this was a firewall issue, I basically tried enabling all in/out traffic. This did not seem to remedy the problem. Also figuring it could possibly be some client networking issue, I restarted the clients on the LAN. This did not help. I also ran route flush and reset the routes manually. So I am a bit stumped, and would be very grateful for any thoughts on what the problem might be.

    Read the article

  • How do I see what connections are being made?

    - by Coldblackice
    My DDWRT router is showing that my computer has a connection count around 600! The router is at 100% CPU use. How can I see what's making all the connections? So far, I've opened up Resource Monitor and checked the network tab. I can sort by which program is using the most network bandwidth (Pale Moon browser), but I can't see what's making all of the connections. Or rather, where all the connections are being toward (trying to find what tab must be making all of these connections). I've also tried netstat -A, but it apparently doesn't show the actual number of connections being made. At least, the list of established connections isn't very long, by any means (like enough to account for the 500+ connections apparently being made.

    Read the article

  • Using Juniper EX3300 as a router

    - by Richard Whitman
    So I have a Juniper EX3300 Switch. One of its uplink ports (ge-0/1/0) is connected to my ISP's router. ISP router's port address is xx.xx.xx.109. My switch's IP address is xx.xx.xx.110. From the switch, I can ping to xx.xx.xx.109 and any other IP in the world. I mean its connected to the Internet. I connected the port eth0 of a computer (running Ubuntu) to the port ge-0/0/0 of the switch (which in the same VLAN as ge-0/1/0). I configured the port eth0 as follows: iface eth0 inet static address yy.yy.yy.208 netmask 255.255.255.240 gateway xx.xx.xx.110 yy.yy.yy.208 is assigned to me by the ISP. So, now I can ping to the switch (xx.xx.xx.110) from this computer. But I can not ping to either xx.xx.xx.109 (ISP router) or any other IP. I want this computer to be connected to the Internet. What am I doing wrong? Here are some of the configurations on my switch: interfaces { ge-0/0/0 { unit 0 { family ethernet-switching; } } . . . ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family ethernet-switching { port-mode access; } } } . . . vlan { unit 0 { family inet { address 10.0.1.1/24; } } unit 1 { family inet { address xx.xx.xx.110/30; } } } } . . . routing-options { static { route 0.0.0.0/0 { next-hop xx.xx.xx.109; retain; } } } vlans { Cogent { vlan-id 3; interface { ge-0/1/0.0; ge-0/0/0.0; ge-0/0/1.0; ge-0/0/2.0; ge-0/0/3.0; } l3-interface vlan.1; } TFLan { vlan-id 2; interface { ge-0/0/5.0; ge-0/0/6.0; ge-0/0/7.0; ge-0/0/8.0; ge-0/0/9.0; ge-0/0/10.0; ge-0/0/11.0; ge-0/0/12.0; ge-0/0/13.0; ge-0/0/14.0; ge-0/0/15.0; ge-0/0/16.0; ge-0/0/17.0; ge-0/0/18.0; ge-0/0/19.0; ge-0/0/20.0; ge-0/0/21.0; ge-0/0/22.0; ge-0/0/23.0; ge-0/0/4.0; } l3-interface vlan.0; } }

    Read the article

  • Mac Mini's internet very slow, every other device fine (PC, iPhone, Xbox 360)

    - by alex
    I recently haven't used my Mac Mini for about 5 days (however it was left on). I seem to be able to connect and get great download / upload speeds through my PC, Xbox 360, iPhone and parents' laptop. However, my Mac Mini is very slow. OS X's Mail.app is downloading mail at 0.4kbps and then dropping to 0. Skype file transfers are doing the same. Browsing the net is a terrible experience. It is taking 30 seconds or more to download basic pages. All of my devices connect wirelessly to a Netgear router / modem. I have tried giving the Mac Mini a manual IP, and renew DHCP lease, as well as flush DNS in Terminal. I have also rebooted the router / modem twice, and the Mac Mini twice. Do you know what could be causing this? Thanks

    Read the article

  • Dlink DIR-615 suddenly stops working - Orange internet light

    - by zm15
    I unplugged my Dlink DIR-615 router last night from the wall due to a storm rolling in. I've done this countless times, no problem. However, when I went to plug it in and use the internet today, nothing. Check everything, cycled everything. Hard reset the router, nothing. The little globe on the front is red/orange, and it should be green. Windows gives me an error of a "DNS Issue", and the internet works when connected directly to the modem. How can I fix this issue? Why would it suddenly stop working?

    Read the article

  • DNS lookups failing somewhere between firewall and router

    - by TessellatingHeckler
    we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

    Read the article

  • Why is my firewall preventing me from accessing some websites

    - by nosx
    I have an old Belkin router and when I enable the firewall I cannot access certain websites. For example: http://www.avisynth.org With Firewall Enabled: Main page loads and begins to do a meta refresh which never finishes. With Firewall Disabled: Main page loads and the meta refresh completes as normal and I am taken to the wiki page. I have not setup any rules in my firewall that would prevent this site from loading, yet it refuses to load unless I have the firewall disabled completely. My router has a hidden page with advanced settings on it for the firewall which I was able to acccess and take a screenshot of, but I did not want to mess with these values unless I absolutely have to do so: What might be causing this problem and how would I go about fixing it?

    Read the article

  • configure cisco catalyst 3560g with an egress uplink

    - by imaginative
    Currently my setup has our egress uplink connected directly to an external interface on a linux router/firewall/nat gateway. Since the linux box is a single point of failure, I've since setup two openbsd boxes using carp+pf+pfsync in order to gain some additional redundancy. the problem is, I only have one egress uplink (it's still a single point of failure) but need to get it to speak to the active carp node in my openbsd cluster which will server as my new router/firewall/nat cluster. Is there anything specific I need to do on a 3560G in order for me to be able to: 1) Drop the egress uplink into a port 2) Drop one link from the switch to a firewall 2) Drop a second link from a switch to the firewall This is so if one box dies, the other still has the egress link to the switch. Is putting them into one VLAN enough? Anything else that needs to go into the configuration for this setup to work?

    Read the article

  • Problems setting up home web server

    - by putmatrix
    Has anyone been able to get a server working with the router smcwbr14t-g? Although I have been able to get Apache set up correctly and my website works on the internal IP 192.168.2.101, I've been running into a dead end when trying to get it to show up on my external IP. In my router, there is no option for port forwarding, but there are options for a 'virtual server'. Following the manual, I have it set up like this: http://imgur.com/zrcV7.png I also disabled the firewall. I configured Apache to listen to ports 80, 81, and 443, none of which solved the problem. However, the IP's 192.168.2.101:443 and :81 load fine. The problem is that I still cannot load the web site from my external IP, either from my computer or outside.

    Read the article

  • Port forwarding for VNC on Dynalink RTA1335 not working

    - by Curyous
    I've vnc-java running on an Ubuntu box, with the IP address 192.168.1.68, using port 5800 (because port 5900 is being used for normal VNC). If I connect to 192.168.1.68:5800 using another computer on the network, I can use VNC fine. Using www.whatismyip.com, I find out what my IP address from the outside world is, and if I go directly to that, I get to access my modem/router. If I try to navigate to that IP address, with ':5800' on the end, I get a "This web page is not available." error. I have port forwarding set up in the router as follows: Application Name External Packet Internal Host IP Address Protocol Port IP Address Port VNC ALL TCP/UDP 5800 192.168.1.68 5800 What else do I need to do to get this to work?

    Read the article

  • Separating two networks

    - by Farhan Ali
    I have two routers, R1 and R2. R1 (a stock linksys router running dd-wrt) is connected to internet and is serving internet to a network of 5 devices/PCs running a DHCP server, with a network of 192.168.1.0/24. R1 also serves internet services to R2. R2 (a ubuntu server 12.04) gets internet from R1. R2 has 3 PCs attached to it, runs a DHCP server with a network of 172.22.22.0/24. My requirement is that the clients on both sides should not talk to each other at all – with the exception that R1 clients may access the R2 router through its IP of 192.168.1.x. At the moment, R2 clients are able to ping R1 clients, which is unacceptable, whereas R1 clients cannot ping R2 clients, which is OK. I believe iptables could be set up but I don't know how.

    Read the article

  • Port Forwarding a Specific Port (e.g. 22)

    - by Jerry Blair
    I'm still confused about establishing an SSH connection (port 22) between two computers on different internal networks. For example: I am on my computer with internal IP address IIP-1, connected to my router RT-1. There are 10 IIPs connected to RT-1. I want to establish an SSH connection to IIP-3 which is connected to router RT-2. There are 10 IIPs connected to RT-2. At any time, there can be multiple SSH connections between IIPs on RT-1 and RT-2. Since I only have port 22 available, I don't know which SSH session is talking between which IIPs. I looked at a couple of similar questions but am still unclear on the solution. Thanks much, Jerry

    Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >