Search Results

Search found 11303 results on 453 pages for 'info'.

Page 85/453 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• iOS chat application design, sending/relaying the message over to the end user

  - by AyBayBay

  I have a design question. Let us say you were tasked with building a chat application, specifically for iOS (iOS Chat Application). For simplicity let us say you can only chat with one person at a time (no group chat functionality). How then can you achieve sending a message directly to an end user from phone A to phone B? Obviously there is a web service layer with some API calls. One of the API calls available will be startChat(). After starting a chat, when you send a message, you make another async call, let us call it sendMessage() and pass in a string with your message. Once it goes to the web service layer, the message gets stored in a database. Here is where I am currently stuck. After the message gets sent to the web service layer, how do we then achieve sending/relaying the message over to the end user? Should the web server send out a message to the end user and notify them, or should each client call a receiveMessage() method periodically, and if the server side has some info for them it can then respond with that info? Finally, how can we handle the case in which the user you are trying to send a message to is offline? How can we make sure the end user gets the packet when he moves back to an area with signal?

  Read the article

• How to connect two ubuntu computers with ethernet cable

  - by Lukasz Zaroda

  I'm trying to connect with ethernet cable two computers - desktop and laptop. What I want to do is transfer a lot of data from one to another. The problem is that I'm doing everything from: How to network two Ubuntu computers using ethernet (without a router)? But after that, ping always gives me "Destination host unreachable". I was searching a while but couldn't figure out what is a reason it doesn't work, maybe it's something about my devices or maybe someone will have another idea. Ethernet cable I got with my router. There is a text printed on it: Aurit Data Cable Cat.5 UTP 26AWG 4PAIR AWM PUC 75°C EIA/TIA 568B It's connecting now my desktop to router, so I can send this question. My desktop: System: Ubuntu 12.04 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) "ethtool -i eth0" output: driver: r8169 version: 2.3LK-NAPI firmware-version: rtl_nic/rtl8168d-1.fw bus-info: 0000:01:00.0 supports-statistics: yes supports-test: no supports-eeprom-access: no supports-register-dump: yes My laptop: System: Ubuntu 14.04 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 08) "ethtool -i eth0" output: driver: alx version: firmware-version: bus-info: 0000:01:00.0 supports-statistics: no supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no My iptables are accepting everything. Any ideas why I cannot reach other computer?

  Read the article

• MSDN Live 2010 &ndash; Delivered : 24 sessions (4 x 6) on Visual Studio and Team Foundation Server

  - by terje

  We (Mikael Nitell and me) got a whole track on the Norwegian MSDN Live tour this year.  We did these as a pair, and covered 4 cities over 4 days, 6 sessions per day, taking 8 hours to come through it.  The Islandic volcano made the travels a bit rough, but we managed 6 flights out of 8. The first one had to go by van instead, 7-8 hour drive each way together with other MSDN Live presenters – a memorable tour! Oslo was the absolute top point.  We had to change hall to a bigger one. People were crowding, and even the big hall was packed!  The presentations were mostly based on demos, but we had a few slides as well.  They have been uploaded to my SkyDrive.  Info to aliens – some of the text may be Norwegian. The sessions were as follows: Overview of news in Visual Studio and Team Foundation server 2010 Ensuring Quality with VS/TFS 2010 Releasing products with VS/TFS 2010 No More No Repro with VS/TFS 2010 Performance Testing and Parallel Programming with VS/TFS 2010 Migrating to VS/TFS 2010 Tips, tricks, news and some best practices with VS/TFS 2010   In the coming days, I will post up examples from the demos too, with explanations of how they are intended to work. These entries will also contain stuff we had to remove from the actual presentations due to the time constraints. We managed to create recordings of two of the sessions, which will be uploaded to Channel 9 by Microsoft, afaik.   I will update this blog with information about exact locations when that is done. Also note we’re (read:Osiris Data AS) running both Upgrade and Deep Dive courses  on VS/TFS 2010 now in May.  Please look here for more info. If you want to be informed, follow me on Twitter.  All blog entries will be announced on twitter.

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Can't install or update Ubuntu after using parameter acpi_osi = Linux

  - by Lucas Leitão

  I recently had an issue with my acer 4736z notebook because I was having a blank screen after booting the OS, then someone told me to use the parameter GRUB_CMDLINE_LINUX_DEFAULT = "quiet splash acpi_osi = Linux" after quiet splash inside the grub. It worked for me, but since then I can't install a thing or update anything on Linux because it says Removing linux-image-extra-3.5.0-17-generic ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic update-initramfs: Deleting /boot/initrd.img-3.5.0-17-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT: not found run-parts: /etc/kernel/postrm.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postrm.d at /var/lib/dpkg/info/linux-image-extra-3.5.0-17-generic.postrm line 328. dpkg: erro ao processar linux-image-extra-3.5.0-17-generic (--remove): sub-processo script post-removal instalado retornou estado de saída de erro 1 Removendo linux-image-3.5.0-17-generic ... Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic update-initramfs: Deleting /boot/initrd.img-3.5.0-17-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.5.0-17-generic /boot/vmlinuz-3.5.0-17-generic /usr/sbin/grub-mkconfig: 11: /etc/default/grub: GRUB_CMDLINE_LINUX_DEFAULT: not found run-parts: /etc/kernel/postrm.d/zz-update-grub exited with return code 127 Failed to process /etc/kernel/postrm.d at /var/lib/dpkg/info/linux-image-3.5.0-17-generic.postrm line 328. dpkg: erro ao processar linux-image-3.5.0-17-generic (--remove): sub-processo script post-removal instalado retornou estado de saída de erro 1 Erros foram encontrados durante o processamento de: linux-image-extra-3.5.0-17-generic linux-image-3.5.0-17-generic E: Sub-process /usr/bin/dpkg returned an error code (1) I already tried to remove older kernels but it gives me the same message. Do you have a clue about what should I do?

  Read the article

• 1.5 TB USB Drive failed to mount

  - by user89348

  Seagate 1.5Tb FreeAgent USB Hard Drive. Formatted FAT32. I figure it is 75% full. Used to work fine in XUBUNTU it shows up in Cairo Dock but when I click on it I get "failed to mount drive'. Nautilus does not display the icon nor does Thunar. Windows Vista will no longer recognise drive either. Back Track 5R3 also no longer fails to mount it. BUT and here is the BIG BUT my Pioneer DV-410 reads the files and plays the everything just fine. I believe this all happened after an unclean shutdown / XUbuntu 12.10 system freeze. Why can't XUBUNTU mount this drive when a crappy 13 year old DVD player can mount it. I am desperate to back up the data before just in case the drive becomes completely unreadable. Using XUBUNTU 12.10 Quantal current 3.5.0.17 Kernel (past 3 Kernels wont read it either) and all newest apt-get update / dist-upgrade are applied. I will post any other info you folks request as needed. Additional info as requested by githlar. $ sudo fsck.vfat /dev/sdb dosfsck 3.0.13, 30 Jun 2012, FAT32, LFN Read 512 bytes at 0:Input/output error $ lsusb Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter Bus 002 Device 002: ID 0bc2:3001 Seagate RSS LLC Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

  Read the article

• Fixing Windows7 Bootmgr

  - by Ashfame

  I made my laptop Dell XPS 15z dual boot with Ubuntu last year, and something went wrong & BOOTMGR of my windows got fried. I couldn't fix it that time. And I kept using Ubuntu. I don't even remember whether I installed directly via a live usb or used wubi, sorry. I installed 11.10 at that point of time, but right now I am on 12.10. Today, I got to know about the Boot repair tool, so I was wondering with this tool may be I can figure out what's exactly wrong with my setup. This is my Boot info - http://paste.ubuntu.com/1343575/ If I select the Win7 entry on GRUB2, I get the error BOOTMGR is missing. Press Ctrl-Alt-Del. Now the thing is I have read numerous links on how this could be fixed, but I don't feel comfortable without knowing what I am doing. So unless I am sure what a certain tool would do, I would prefer fixing it by hand (manually editing files). So reading from my boot info file, can anyone explain it to me what's messed up wrong here and what could fix it? I certainly can't afford to have my ubuntu install unbootable right now, but looking into this issue is bothering me too much. Help appreciated! I have Win7 DVD & Ubuntu live USBs with me, I am just looking for a sure shot way of fixing Win7 without any harm to my existing Ubuntu install.

  Read the article

• How do I get Graphics drivers / bluetooth / card reader working on an Acer Aspire V3-571G?

  - by Adam

  A couple of days ago I bought an Acer Aspire V3-571G laptop without a system installed on it. The only thing that was there was Linux Linpus. I created a bootable CD with Ubuntu 12.04 64-bit - I read that my processor was 64 bit and that it might be a good configuration for my gear (I'm not especially fluent with all the computer stuff, still trying to learn) and replaced Linpus with Ubuntu. Everything seemed to work fine, but there're few exceptions to that which came pass my way. My bluetooth doesn't work. It seems to be switched on, but when I check my system settings the button is actually off, and I can't drag it 'perminently' to the 'on' position. Tried a couple of commands I found on the net, none of them helped and there was no word whatsoever in my BIOS settings about enabling bluetooth. My card reader has some serious problems with copying more than one file at a time. I tried to put some music on my phone through a MicroSD card adapter (because my bluetooth doesn't work) and it got stuck every single time I copied an album on it. I'm not sure if all my drivers were properly installed, so I checked in the terminal if it could tell me sth about my graphics. typed: sudo lshw -c display and what i got was: *-display UNCLAIMED description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller cap_list configuration: latency=0 resources: memory:b2000000-b2ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:2000(size=128) *-display description: VGA compatible controller product: Ivy Bridge Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:b3000000-b33fffff memory:c0000000-cfffffff ioport:3000(size=64) As I said I'm no expert and not english-speaking generally, but it doesn't seem to be right. I've got a NVIDIA GeForce GT 640M.

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

  - by Tim

  Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

  Read the article

• Cannot play windows WMA lossless files on Rhythmbox

  - by sr71

  I have installed Ubuntu 10.10 with all its updates (without Windows) on it’s own drive and everything is working fine. I want to play WMA audio files, also mp3 files. The mp3 files play fine. The WMA files do not play. Used "Rhythmbox Music Player" with and without "Ubuntu-restricted" -extras. Still does not play the lossless windows audio files. I am frustrated with searching to play a WMA file ("download this converter"), but one cannot use this until one "deletes this". I have done everything but it still does not play my windows lossless files that I made from all my CD’s. I am looking for a music player that I can use to play mp3’s and WMA lossless music files and automatically put the album cover on and update the info if one exists. Installation should be as simple as possible. Right now I am back to the original virgin Ubuntu 10.10 with all the recent updates. This computer will do nothing but play music (mp3 and WMA) through a stereo system. I also use Internet to update album info for the music. I do not care what bells and whistles the music player program has, as long as it is an easy install and just plays my mp3 and wma lossless music files. Any help would be appreciated.

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• 12.10 upgrade broke brightness keys [closed]

  - by Chris Morgan

  I have been running Ubuntu (64-bit) on my HP 6710b laptop (Core 2 Duo with integrated graphics) for several years, and the backlight brightness keys have always worked. Since I upgraded to Ubuntu 12.10 earlier today, those keys do not work any more. The secondary function keys: Fn+F3: sleep; still works (and considerably faster than ever before!) Fn+F8: battery info; still works Fn+F9: reduce brightness; stopped working in 12.10 Fn+F10: increase brightness; stopped working in 12.10 It may also be worth while mentioning that X does not appear to be receiving the brightness events at all, or at least not sending them out further. (This I detected with a key logger I wrote for a Uni project, which uses X's Record extension; it is informed of the sleep and battery info keystrokes, but doesn't receive the brightness ones at all.) In the mean time, I know that I can use the Brightness & Lock settings screen to alter the brightness. (Wow! I can suddenly make my backlight darker than I could before—I can go right down to turning the backlight off, something I couldn't do before... but this model has a fairly dim screen, so I don't expect to use that much, if ever.) How can I get the brightness keys working again? This question is probably strongly related to I can't control my Brightness in HP Compaq 6710s.

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• How does one find out which application is associated with an indicator icon in Ubuntu 12.04?

  - by Amos Annoy

  It is trivial to do this in Ubuntu 10.04. The question is specific to Ubuntu 12.04. This has nothing to do (does it?) with right click. How can an indicator's icon in Ubuntu 12.04 be matched with the program responsible for it's manifestation on the top panel? A list of running applications can include all processes using System Monitor. How is the correct matching process found for an indicator? (the examination of SM points out a rather poignant factor in the faster depletion and shortened run time on battery - the ambient quiescent CPU rate in 12.04 is now well over 20% when previously it was well under 10% in 10.04, between 5% and 7%!) (I have a problem with the battery indicator - it sometimes has % and other times hh:mm - it is necessary to know the ap. & v. to get more info on controlling same. ditto: There are issues with other indicator aps.) Details from: How can I find Application Indicator ID's? suggests looking at: file:///usr/share/indicator-application/ordering-override.keyfile [Ordering Index Overrides] nm-applet=1 gnome-power-manager=2 ibus=3 gst-keyboard-xkb=4 gsd-keyboard-xkb=5 which solves the battery identification, and presumably nm is NetworkManager for the rf icon, but the envelope, blue tooth and speaker indicator aps. are still a mystery. (Also, the ordering is not correlated.) Mind you, it was simple in the past to simply right click to get the About option to find the ap. & v. info. browsing around and about: file:///usr/share/indicator-application/ordering-override.keyfile examined: file:///usr/share/indicators file:///usr/share/indicators/messages/applications/ ... perhaps?/presumably? the information sought may be buried in file:///usr/share/indicators

  Read the article

• Friday Stats

  - by jjg

  As some of you may have noticed, we've recently opened a new repository in the Code Tools project for small utilities which can be used to gather info about the OpenJDK code base and builds. 1 The latest addition is a utility for analyzing the class file versions in a collection of class files. I've posted an example set of results from analyzing the class files in an OpenJDK build on Linux. 2. Most of the files are version 52 files as you would expect, but there is a surprising number of version 51 and 50 files, as well as a handful of v45.3 files as well. Digging deeper, it turns out that Nashorn is still using version 51 class files, and the Serviceability Agent is still using version 50 class files and one 45.3 class file, leaving the remainder of the 45.3 class files coming from RMI. For more info on the different class file versions, see Joe Darcy's class file version decoder rIng. Thanks to Stuart Marks for planting the seed for the class file version tool. See the project page, repo, and mail archive. http://cr.openjdk.java.net/~jjg/cfv-summary/open/

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• eSTEP TechCast-Special - October 2012

  - by uwes

  Dear partner, we are pleased to announce our eSTEP TechCast-Special on Thursday 18th of October and would be happy if you could join. Please see below the details for the next TechCast.Date and time:Thursday, 18. October 2012, 11:00 - 12:00 BST (12:00 - 13:00 CEST; 14:00 - 15:00 GST) Title: Oracle OpenWorld Systems Update Abstract:In this special TechCast we will give you a brief update to News and Announcements of Oracle Open World 2012. Special focus will be on Announcements around the Systems products and partner relevant News from Oracle OpenWorld. Target audience: Tech Presales Speaker: HW Enablement Team Call Info:Call-in-toll-free number: 08006948154 (United Kingdom)Call-in-toll-free number: +44-2081181001 (United Kingdom) Show global numbers Conference Code: 803 594 3Security Passcode: 9876Webex Info (Oracle Web Conference) Meeting Number: 593 893 048Meeting Password: tech2011 Playback / Recording / Archive: The webcasts will be recorded and will be available shortly after the event in the eSTEP portal under the Events tab, where you could find also material from already delivered eSTEP TechCasts. Use your email-adress and PIN: eSTEP_2011 to get access. Feel free to have a look. We are happy to get your comments and feedback. ">

  Read the article

• eSTEP TechCast - December 2012

  - by uwes

  Dear partner, we are pleased to announce our next eSTEP TechCast on Thursday 6th of December and would be happy if you could join. Please see below the details for the next TechCast.Date and time:Thursday, 06. December 2012, 11:00 - 12:00 GMT (12:00 - 13:00 CET; 15:00 - 16:00 GST) Title: Innovations with Oracle Solaris Cluster 4 Abstract:Oracle Solaris Cluster 4.0 is the version of Solaris Cluster that runs with Oracle Solaris 11. In this webcast we will focus at the integration of the cluster software with the IPS packaging system of Solaris 11, which makes installing and updating the software much easier and much more reliable, especially with virtualization technologies involved. Our webcast will also reflect new versions of Oracle Solaris Cluster if they will be announced in the meantime. Target audience: Tech Presales Speaker: Hartmut Streppel Call Info:Call-in-toll-free number: 08006948154 (United Kingdom)Call-in-toll-free number: +44-2081181001 (United Kingdom) Show global numbers Conference Code: 803 594 3Security Passcode: 9876Webex Info (Oracle Web Conference) Meeting Number: 255 760 510Meeting Password: tech2011 Playback / Recording / Archive: The webcasts will be recorded and will be available shortly after the event in the eSTEP portal under the Events tab, where you could find also material from already delivered eSTEP TechCasts. Use your email-adress and PIN: eSTEP_2011 to get access. Feel free to have a look. We are happy to get your comments and feedback. Thanks and best regards, Partner HW Enablement EMEA

  Read the article

• How do I know if I'm getting the most out of my video card?

  - by b.long

  My computer at home is a bit lacking, so I want to make sure I'm getting the most out of it while I can. Generally speaking, here are the specs: 4GB Memory AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ × 2 64-bit Ubuntu The terminal shows me the following: me@home:~$ uname -a Linux home 3.0.0-17-generic #30-Ubuntu SMP Thu Mar 8 20:45:39 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux me@home:~$ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] me@home:~$ sudo lshw -C video *-display:0 description: VGA compatible controller product: RV380 [Radeon X600 (PCIE)] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:44 memory:e0000000-efffffff ioport:ac00(size=256) memory:fdef0000-fdefffff memory:fdec0000-fdedffff *-display:1 UNCLAIMED description: Display controller product: RV380 [Radeon X600] vendor: ATI Technologies Inc physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress bus_master cap_list configuration: latency=0 resources: memory:fdee0000-fdeeffff me@home:~$ lspci -nn | grep VGA 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV380 [Radeon X600 (PCIE)] [1002:5b62] The additional drivers menu in System Settings shows me nothing useful and my attempt at installing ATI's Catalyst Control center (drivers that came with the video card) failed. I believe the latest version of Ubuntu at the time was 9.x. What should I do? Install an old version of Ubuntu 9? Use some alternative driver? UPDATE: I might try my hand at a bit from this answer next: "Installing Catalyst Manually (from AMD/ATI's site)" . From a terminal, fgl_glxgears returns *"fgl_glxgears: command not found"*. Any thoughts?

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >