Search Results

Search found 5136 results on 206 pages for 'max dwayne'.

Page 85/206 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• DHCP "no answer" on CentOS 6.4

  - by Kev

  I installed a DHCP server (yum install dhcp) and this is my conf: # create new # specify domain name option domain-name "mydomain.name"; # specify DNS's hostname or IP address option domain-name-servers 10.0.1.1, 10.0.1.2; option ntp-servers 10.0.1.1, 10.0.1.2; allow unknown-clients; # default lease time default-lease-time 2628000; # max lease time max-lease-time 2628000; # about a month # this DHCP server to be declared valid authoritative; # specify network address and subnet mask subnet 10.0.0.0 netmask 255.0.0.0 { # specify the range of lease IP address range dynamic-bootp 10.0.2.1 10.0.2.50; # specify broadcast address option broadcast-address 10.255.255.255; # specify default gateway option routers 10.0.0.1; allow unknown-clients; } service dhcp start reports [ OK ]. Yet, if I disable my other DHCP server (Win2k3) and get a client to try renewing its IP lease, it times out. So I installed dhcping. No matter what options I try, including directing dhcping at my server, adding a client address in the range, adding my hardware address, it replies 'no answer'. I'm also trying -i since that seems to be more akin to what a WinXP client would try to do, based on /var/log/messages. It logs the attempts (from dhcping here) as: Oct 24 18:55:13 newdc dhcpd: DHCPINFORM from 10.0.2.15 via eth0:4 Oct 24 18:55:13 newdc dhcpd: DHCPACK to 10.0.2.15 (00:11:25:66:4e:7f) via eth0:4 Oct 24 18:55:13 newdc dhcpd: DHCPINFORM from 10.0.2.15 via eth0:3 Oct 24 18:55:13 newdc dhcpd: DHCPACK to 10.0.2.15 (00:11:25:66:4e:7f) via eth0:3 Oct 24 18:55:13 newdc dhcpd: DHCPINFORM from 10.0.2.15 via eth0 Oct 24 18:55:13 newdc dhcpd: DHCPACK to 10.0.2.15 (00:11:25:66:4e:7f) via eth0 The :3 and :4 are because I have a few extra Host(A) records for this server so it responds on more than one IP for our intranet app. No answer? It sounds like it should be getting three answers...no? (And if that's the problem, how do I limit the DHCP service to replying from eth0?)

  Read the article

• Disk is spinning down each minute, unable to disable it

  - by lzap

  I played with spindown and APM settings of my Samsung discs and now they spin down every minute. I want to disable it, but it seems it does not accept any of the spindown time or APM values. Nothing works, it's all the same. Please help what values should be proper for it. I do not want it to spin down at all. /dev/sda: ATA device, with non-removable media Model Number: SAMSUNG HD154UI Serial Number: S1Y6J1KZ206527 Firmware Revision: 1AG01118 Standards: Used: ATA-8-ACS revision 3b Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 2930277168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 1430799 MBytes device size with M = 1000*1000: 1500301 MBytes (1500 GB) cache/buffer size = unknown Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 udma7 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * NCQ priority information DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 326min for SECURITY ERASE UNIT. 326min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50024e900300cca3 NAA : 5 IEEE OUI : 0024e9 Unique ID : 00300cca3 Checksum: correct I have the very same disc which I did not "tuned" and it does not spin. But I do not know where to read the settings from. The hdparm only shows this: Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 Edit: It seems the issue was tuned daemon in RHEL6. It was too aggressive, I turned off disc tuning and it seems they are no longer spinning down.

  Read the article

• mailman web UI on localhost with apache2

  - by Thufir

  I'm interested only in running mailman on localhost and would like access to the web interface, but am getting 404: root@dur:~# root@dur:~# ln -s /etc/mailman/apache.conf /etc/apache2/sites-enabled/mailman -v `/etc/apache2/sites-enabled/mailman' -> `/etc/mailman/apache.conf' root@dur:~# root@dur:~# service apache2 restart * Restarting web server apache2 ... waiting . [ OK ] root@dur:~# root@dur:~# curl http://localhost/mailman/admin/ <!DOCTYPE HTML PUBLIC "-//IETF//DTD HTML 2.0//EN"> <html><head> <title>404 Not Found</title> </head><body> <h1>Not Found</h1> <p>The requested URL /mailman/admin/ was not found on this server.</p> <hr> <address>Apache/2.2.22 (Ubuntu) Server at localhost Port 80</address> </body></html> root@dur:~# root@dur:~# tail /var/log/apache2/error.log [Mon Aug 27 13:08:02 2012] [error] [client 127.0.0.1] File does not exist: /var/www/mailman [Mon Aug 27 13:10:16 2012] [error] [client 127.0.0.1] File does not exist: /var/www/mailman [Mon Aug 27 13:29:27 2012] [notice] caught SIGTERM, shutting down [Mon Aug 27 13:29:27 2012] [error] python_init: Python version mismatch, expected '2.7.2+', found '2.7.3'. [Mon Aug 27 13:29:27 2012] [error] python_init: Python executable found '/usr/bin/python'. [Mon Aug 27 13:29:27 2012] [error] python_init: Python path being used '/usr/lib/python2.7/:/usr/lib/python2.7/plat-linux2:/usr/lib/python2.7/lib-tk:/usr/lib/python2.7/lib-old:/usr/lib/python2.7/lib-dynload'. [Mon Aug 27 13:29:27 2012] [notice] mod_python: Creating 8 session mutexes based on 6 max processes and 25 max threads. [Mon Aug 27 13:29:27 2012] [notice] mod_python: using mutex_directory /tmp [Mon Aug 27 13:29:28 2012] [notice] Apache/2.2.22 (Ubuntu) mod_python/3.3.1 Python/2.7.3 mod_ruby/1.2.6 Ruby/1.8.7(2011-06-30) configured -- resuming normal operations [Mon Aug 27 13:29:58 2012] [error] [client 127.0.0.1] File does not exist: /var/www/mailman root@dur:~# Although I did have to tinker a bit with mailmain to get that recognized. While I don't need to setup web access using MM list passwords, I would like to setup web admin to add/remove mailing lists. How do I configure apache or mailman so that I can navigate to http://localhost/mailman/admin/? As per installing mailman, I setup aliases as so: root@dur:~# root@dur:~# cat /etc/aliases usenet: root ## mailman mailing list mailman: "|/var/lib/mailman/mail/mailman post mailman" mailman-admin: "|/var/lib/mailman/mail/mailman admin mailman" mailman-bounces: "|/var/lib/mailman/mail/mailman bounces mailman" mailman-confirm: "|/var/lib/mailman/mail/mailman confirm mailman" mailman-join: "|/var/lib/mailman/mail/mailman join mailman" mailman-leave: "|/var/lib/mailman/mail/mailman leave mailman" mailman-owner: "|/var/lib/mailman/mail/mailman owner mailman" mailman-request: "|/var/lib/mailman/mail/mailman request mailman" mailman-subscribe: "|/var/lib/mailman/mail/mailman subscribe mailman" mailman-unsubscribe: "|/var/lib/mailman/mail/mailman unsubscribe mailman" root@dur:~# Perhaps these can be used somehow?

  Read the article

• Cannot exclude a path from basic auth when using a front controller script

  - by Adam Monsen

  I have a small PHP/Apache2 web application wherein I'd like to do two seemingly incompatible operations: Route all requests through a single PHP script (a "front controller", if you will) Secure everything except API calls with HTTP basic authentication I can satisfy either requirement just fine in isolation, it's when I try to do both at once that I am blocked. For no good reason I'm trying to accomplish these requirements solely with Apache configuration. Here are the requirements stated as an example. A GET request for this URL: http://basic/api/listcars?max=10 should be sent through front.php without requiring basic auth. front.php will get /api/listcars?max=10 and do whatever it needs to with that. Here's what I think should work. In my /etc/hosts I added 127.0.0.1 basic and I am using this Apache config: <Location /> AuthType Basic AuthName "Home Secure" AuthUserFile /etc/apache2/passwords require valid-user </Location> <VirtualHost *:80> ServerName basic DocumentRoot /var/www/basic <Directory /var/www/basic> <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{SCRIPT_FILENAME} !-f RewriteCond %{SCRIPT_FILENAME} !-d RewriteRule ^(.*)$ /front.php/$1 [QSA,L] </IfModule> </Directory> <Location /api> Order deny,allow Allow from all Satisfy any </Location> </VirtualHost> But I still always get a HTTP 401: Authorization Required response. I can make it work by changing <Location /api> into <Location ~ /api> but this allows more than I want to past basic auth. I also tried changing the <Directory /var/www/basic> section into <Location />, but this doesn't work either (and it results in some strange values for PATH_TRANSLATED being passed to the script). I searched around and found many examples of selective exclusion of basic auth, but none that also incorporated a front controller. I could certainly do something like handle basic auth in the front controller, but if I can have Apache do that instead I'll be able to keep all authentication logic out of my PHP code. A friend suggested splitting this into two vhosts, which I know also works. This used to be two separate vhosts, actually. I'm using Apache 2.2.22 / PHP 5.3.10 on Ubuntu 12.04.

  Read the article

• Any reason not to disable Windows kernel paging?

  - by Nathaniel

  So I'm planning on eventually going to 2 GB (mobo max) RAM from 1 GB, and I want to disable kernel paging once I do, because I've heard it can give a performance boost (and that I believe). Any reason not to do it or any general thoughts about it? Edit: for clarification, this is not disabling general RAM paging. This is disabling having kernel memory paged (or at least parts of it, as Charlls noted).

  Read the article

• blur a moving area in a movie on osx

  - by Stefano Borini

  Note, there's already a question on this regard, but it's totally useless. I need to blur, or put a small opaque mask to a moving object on a movie I took, I am using mac osx. Clearly, I don't want to shell out a lot of money for something so simple, so getting adobe premiere or similar software is a no go. I could however consider paying a small software (max 30 dollars) for this specific task.

  Read the article

• VMWare-Mount not recognizing virtual disks

  - by user36175

  I have two disks as .vmdk files, and four as .vdi files. I can boot virtual machines on them with Sun xMV VirtualBox, and they work just fine. However, I want to mount them on my local computer so I can read some files off of them without starting a virtual machine. I downloaded the vmware-mount utility, but I get this error, even when mounting .vmdk files, which should be VMWare images... Unable to mount the virtual disk. The disk may be in use by a virtual machine, may not have enough volumes or mounted under another drive letter. If not, verify that the file is a valid virtual disk file. Thinking it's a problem with the utility, I downloaded the SDK and made my own simple program in C to try to mount a disk. It just initializes the API, connects to it, then attempts to open the disk. I get this error, once again claiming it is not a virtual disk: **LOG: DISKLIB-DSCPTR: descriptor above max size: I64u **LOG: DISKLIB-LINK : "f:\programming\VMs\windowstrash.vdi" : failed to open (The file specified is not a virtual disk). **LOG: DISKLIB-CHAIN : "f:\programming\VMs\windowstrash.vdi" : failed to open (The file specified is not a virtual disk). **LOG: DISKLIB-LIB : Failed to open 'f:\programming\VMs\windowstrash.vdi' with flags 0x1e (The file specified is not a virtual disk). ** FAILURE ** : The file specified is not a virtual disk The files are clearly virtual disks, though, since I can actually mount and use them with a virtual machine. I tried detaching them from any VMs and trying again, but I got the same results. Any ideas? Maybe the "descriptor above max size" is a hint? Some more info: the .vmdk disks were created on other computers. I just copied them to mine and created new VMs around them, but they work fine. All the .vdi files were created on my machine. Not sure if that affects anything. Update: WinMount can mount the file.. so the problem seems to be with vmware-mount.

  Read the article

• Apache memory leak with Subversion server

  - by bruce grissom

  Does anyone know of a way to fix the Apache memory leak in relation to Subversion Server? We have a windows server 2003 machine running Apache to host Subversion. From day one, we have had memory leak issues and have not found a solution yet. All we do is monitor our server when when the memory use reaches near the max it can handle we have to restart Apache.

  Read the article

• What's a good 3D modelling editor, other than Blender, that can be used within Unity 3D?

  - by Arc

  Unity 3D is an amazing tool for quickly creating good-looking, fun games. Unfortunately, its not intended to be used for actually designing your characters or complex levels. Blender is the general low-budget answer for this, but is difficult to understand when compared to proprietary programs, say, 3DS Max. What else is out there?

  Read the article

• Garbled text in Screen [closed]

  - by Prabin Dahal

  The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

  Read the article

• How do I get rid of HTTP_CACHE_CONTROL header in squid 3?

  - by Arsen Zahray

  I'm trying to configure an anonymous proxy using squid. I've set forwarded_for delete via delete but Squid 3 still adds an other header to the web requests that go through it: HTTP_CACHE_CONTROL = max-age=259200 I've tried cache_control delete but that doesn't work. How do I get rid of squid's cache_control header? I don't want for it to interfere with the actual web requests that contain cache-control header; But I want for it not to attach its own header

  Read the article

• Why has my zoom feature stopped working in OSX 10.6?

  - by Kev

  For the life of me I can't get the zoom feature to work on OSX 10.6 on my Max Mini. It's a fresh install, I have the wireless mighty mouse with the small grey scroll ball and the small wireless Apple metal keyboard. I've tried enabling "Zoom using scroll ball whilst holding ^Control" mouse System Preference. I also tried enabling Zoom in "Universal Access" in the System Preferences. This did work in OSX 10.5, but seems to have stopped since I installed 10.6.

  Read the article

• How Do I Cache Just the Homepage with Apache .htaccess?

  - by Volomike

  This config is close... <FilesMatch "\.(php)$"> Header set Cache-Control "max-age=7200, must-revalidate" </FilesMatch> ...but it does all php pages, not just the home page like I want. Basically the developer said he wants example.com to be cached, while: http://example.com/electronics/ would not be cached. Note the developer is using pretty URLs with an MVC framework that runs everything through index.php.

  Read the article

• Android emulator performance on linux

  - by Rado

  I installed the android SDK and eclipse plugin on my laptop, but I was surprised to find out that the emulator eats up 100% of one of my cpu cores. I have exactly the same setup on a desktop machine that does not have this issue. Both computers are running arch linux and both were updated yesterday. Granted, the desktop has better hardware than the laptop, but I was expecting to get closer to 50% cpu usage than 100% on the laptop. Both android virtual devices have the same specs: CPU: ARM Target: Android 2.3.3 - API Level 10 Skin: WVGA800 SD Card: 512M hw.lcd.density: 240 vm.heapSize: 24 hw.ramSize: 256 Laptop host has Intel Core 2 T7200 @ 2GHz cpu with 2Gb RAM. Desktop host has AMD Phenom II X4 940 @ 3GHz cpu with 8Gb RAM. The android emulator uses only 1 core and here are the CPU usage results: Laptop: Cpu0 : 22.8%us, 76.5%sy, 0.0%ni, 0.3%id, 0.0%wa, 0.0%hi, 0.3%si, 0.0%st Cpu1 : 11.2%us, 2.4%sy, 0.0%ni, 86.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2055484k total, 1860304k used, 195180k free, 5276k buffers Swap: 2000088k total, 106872k used, 1893216k free, 350780k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2026 xyz 20 0 396m 207m 7192 R 100 10.3 4:11.58 emulator-arm Desktop: Cpu0 : 0.7%us, 0.0%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 1.3%us, 0.0%sy, 0.0%ni, 98.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 5.0%us, 1.3%sy, 0.0%ni, 91.9%id, 1.7%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.3%us, 0.3%sy, 0.0%ni, 99.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 7666324k total, 6506808k used, 1159516k free, 1650960k buffers Swap: 8988348k total, 0k used, 8988348k free, 2867300k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2811 xyz 20 0 392m 220m 6276 S 8 2.9 0:33.58 emulator-arm Is there any way I can improve the emulator performance on the laptop? [UPDATE] I ran the emulator with the same settings, on the same laptop under Win7 and after starting up, it didn't use 100% of a CPU core unlike under linux. Also, I tried running the emulator from a terminal in Linux and I get this message when I don't get it under the desktop Linux host: Could not configure '/dev/hpet' to have a 1024Hz timer. This is not a fatal error, but for better emulation accuracy type: 'echo 1024 /proc/sys/dev/hpet/max-user-freq' as root. I'm not really familiar with rtc or hpet, but it doesn't seem that max-user-freq setting does anything, I still get the same warning.

  Read the article

• Gateway on a virtual network interface used by LXC guests

  - by linkdd

  I'm currently having some problems with configuring a gateway for a virtual network interface. Here is what I've done : I created a virtual network interface : # brctl addbr lxc0 # brctl setfd lxc0 0 # ifconfig lxc0 192.168.0.1 promisc up # route add -net default gw 192.168.0.1 lxc0 The output of ifconfig gave me what I wanted : lxc0 Link encap:Ethernet HWaddr 22:4f:e4:40:89:bb inet adr:192.168.0.1 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::88cf:d4ff:fe47:3b6b/64 Scope:Lien UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:623 errors:0 dropped:0 overruns:0 frame:0 TX packets:7412 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:50329 (49.1 KiB) TX bytes:335738 (327.8 KiB) I configured dnsmasq to provide a DNS server (using the default : 192.168.1.1) and a DHCP server. Then, my LXC guest is configured like this : lxc.network.type=veth lxc.network.link=lxc0 lxc.network.flags=up Every thing is working perfectly, my containers have an IP (192.168.0.57 and 192.168.0.98). I can ping the host and the containers from the containers and from the host : (host)# ping -c 3 192.168.0.114 PING 192.168.0.114 (192.168.0.114) 56(84) bytes of data. 64 bytes from 192.168.0.114: icmp_req=1 ttl=64 time=0.044 ms 64 bytes from 192.168.0.114: icmp_req=2 ttl=64 time=0.038 ms 64 bytes from 192.168.0.114: icmp_req=3 ttl=64 time=0.043 ms --- 192.168.0.114 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1998ms rtt min/avg/max/mdev = 0.038/0.041/0.044/0.007 ms (guest)# ping -c 3 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_req=1 ttl=64 time=0.048 ms 64 bytes from 192.168.0.1: icmp_req=2 ttl=64 time=0.042 ms 64 bytes from 192.168.0.1: icmp_req=3 ttl=64 time=0.042 ms --- 192.168.0.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.042/0.044/0.048/0.003 ms Now, it's time to configure the host as a gateway for the network 192.168.0.0/24 : #!/bin/sh # Clear rules iptables -F iptables -t nat -F iptables -t mangle -F iptables -X iptables -A FORWARD -i lxc0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o lxc0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward The final test failed completely, ping the outside : (guest)# ping -c 3 google.fr PING google.fr (173.194.67.94) 56(84) bytes of data. From 192.168.0.1: icmp_seq=3 Redirect Host(New nexthop: wi-in-f94.1e100.net (173.194.67.94)) From 192.168.0.1 icmp_seq=1 Destination Host Unreachable From 192.168.0.1 icmp_seq=2 Destination Host Unreachable From 192.168.0.1 icmp_seq=3 Destination Host Unreachable --- google.fr ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2017ms Did I missed something ?

  Read the article

• How to run Django 1.3/1.4 on uWSGI on nginx on EC2 (Apache2 works)

  - by Tadeck

  I am posting a question on behalf of my administrator. Basically he wants to set up Django app (made on Django 1.3, but will be moving to Django 1.4, so it should not really matter which one of these two will work, I hope) on WSGI on nginx, installed on Amazon EC2. The app runs correctly when Django's development server is used (with ./manage.py runserver 0.0.0.0:8080 for example), also Apache works correctly. The only problem is with nginx and it looks there is something else wrong with nginx / WSGI or Django configuration. His description is as follows: Server has been configured according to many tutorials, but unfortunately Nginx and uWSGI still do not work with application. ProjectName.py: import os, sys, wsgi os.environ.setdefault("DJANGO_SETTINGS_MODULE", "ProjectName.settings") from django.core.wsgi import get_wsgi_application application = get_wsgi_application() I run uWSGI by comand: uwsgi -x /etc/uwsgi/apps-enabled/projectname.xml XML file: <uwsgi> <chdir>/home/projectname</chdir> <pythonpath>/usr/local/lib/python2.7</pythonpath> <socket>127.0.0.1:8001</socket> <daemonize>/var/log/uwsgi/proJectname.log</daemonize> <processes>1</processes> <uid>33</uid> <gid>33</gid> <enable-threads/> <master/> <vacuum/> <harakiri>120</harakiri> <max-requests>5000</max-requests> <vhost/> </uwsgi> In logs from uWSGI: *** no app loaded. going in full dynamic mode *** In logs from Nginx: XXX.com [pid: XXX|app: -1|req: -1/1] XXX.XXX.XXX.XXX () {48 vars in 989 bytes} [Date] GET / => generated 46 bytes in 77 m secs (HTTP/1.1 500) 2 headers in 63 bytes (0 switches on core 0) added /usr/lib/python2.7/ to pythonpath. Traceback (most recent call last): File "./ProjectName.py", line 26, in <module> from django.core.wsgi import get_wsgi_application ImportError: No module named wsgi unable to load app SCRIPT_NAME=XXX.com| Example tutorials that were used: http://projects.unbit.it/uwsgi/wiki/RunOnNginx https://docs.djangoproject.com/en/1.4/howto/deployment/wsgi/ Do you have any idea what has been done incorrectly, or what should be done to make Django work on uWSGI on nginx on EC2?

  Read the article

• Lync 2010, Kamailio, & Trixbox 2.6.23 (Asterisk 1.4)

  - by slashp

  I'm having an issue trying to connect Lync 2010 phone calls with our trixbox PBX. I've gotten to the point where Kamailio seems to be functioning properly and acting as a bridge between TCP traffic (from Lync) & UDP traffic (to the trixbox, as Asterisk 1.4 does not support SIP over TCP). Our Lync box IP: 10.100.10.41 Our Kamailio box IP: 10.100.10.44 Our trixbox IP: 10.100.10.2 The issue I'm running into is as follows when enabling SIP debugging for the Kamailio box: <--- SIP read from 10.100.10.44:5060 ---> PRACK sip:TNECLTSLY01.contoso.com:5068;transport=Tcp;maddr=10.100.10.41 SIP/2.0 FROM: <sip:9121;[email protected];user=phone>;epid=CF2380792B;tag=4852bab430 TO: <sip:[email protected];user=phone>;epid=CF2380792B;tag=3684a6a24e CSEQ: 24 PRACK CALL-ID: 192daae6-00e1-4140-bddd-0394b35d475b MAX-FORWARDS: 70 Via: SIP/2.0/UDP 10.100.10.44;branch=z9hG4bKcydzigwkX;i=d VIA: SIP/2.0/TCP 10.100.10.41:51677;branch=z9hG4bK159fc989 CONTACT: <sip:TNECLTSLY01.contoso.com:5068;transport=Tcp;maddr=10.100.10.41> CONTENT-LENGTH: 0 USER-AGENT: RTCC/4.0.0.0 MediationServer RAck: 1 23 INVITE <-------------> --- (12 headers 0 lines) --- Sending to 10.100.10.44 : 5060 (NAT) <--- Transmitting (NAT) to 10.100.10.44:5060 ---> SIP/2.0 481 Call leg/transaction does not exist Via: SIP/2.0/UDP 10.100.10.44;branch=z9hG4bKcydzigwkX;i=d;received=10.100.10.44 Via: SIP/2.0/TCP 10.100.10.41:51677;branch=z9hG4bK159fc989 From: <sip:9121;[email protected];user=phone>;epid=CF2380792B;tag=4852bab430 To: <sip:[email protected];user=phone>;epid=CF2380792B;tag=3684a6a24e Call-ID: 192daae6-00e1-4140-bddd-0394b35d475b CSeq: 24 PRACK User-Agent: Asterisk PBX Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY Supported: replaces Content-Length: 0 <------------> trixbox1*CLI> <--- SIP read from 10.100.10.44:5060 ---> ACK sip:[email protected];user=phone SIP/2.0 FROM: "John Jones"<sip:9121;[email protected];user=phone>;tag=4852bab430;epid=CF2380792B TO: <sip:[email protected];user=phone>;tag=3684a6a24e;epid=CF2380792B CSEQ: 23 ACK CALL-ID: 192daae6-00e1-4140-bddd-0394b35d475b MAX-FORWARDS: 70 Via: SIP/2.0/UDP 10.100.10.44;branch=z9hG4bKcydzigwkX;i=d VIA: SIP/2.0/TCP 10.100.10.41:51677;branch=z9hG4bK79a21c CONTENT-LENGTH: 0 My SIP trunk on the trixbox looks like this: [from-lync] exten => _+4XXX!,1,Noop(Stripping + from start of number) exten => _+4XXX!,n,Goto(from-internal,${EXTEN:1}) Though I am still having no luck getting the + stripped or the call to go through. Any ideas would be greatly appreciated. Thank you! -slashp

  Read the article

• How to excport hives from registry in Windows.000 after re-install

  - by Mawg

  I had to reinstall Windwos and my old WIndows directory is now called Windows.000 I tried to resinatll my s/w applications, but one told me it has been insatlled on the max number of PCs, even though this was the first I ever sinsatlled it on. I think it might be ok if I can export teh relvant registry hive from teh old windows & import it into the new ... but how can I do that? Thanks in advance

  Read the article

• dmidecode showing less Memory Capacity than Motherboard spec?

  - by starchx

  We got a supermicro server, http://www.supermicro.com/products/system/1u/5016/sys-5016i-ur.cfm, according spec, the server supports up to 32G memory when using ECC Register Memory. However, when I tried the dmidecode command, it says 24G max memory: [root@c1 ~]# dmidecode | grep Maximum Maximum Size: 256 kB Maximum Size: 1024 kB Maximum Size: 8192 kB Maximum Memory Module Size: 4096 MB Maximum Total Memory Size: 24576 MB Maximum Capacity: 24 GB Maximum Value: Unknown Which one I should trust?

  Read the article

• Malware - Technical anlaysis

  - by nullptr

  Note: Please do not mod down or close. Im not a stupid PC user asking to fix my pc problem. I am intrigued and am having a deep technical look at whats going on. I have come across a Windows XP machine that is sending unwanted p2p traffic. I have done a 'netstat -b' command and explorer.exe is sending out the traffic. When I kill this process the traffic stops and obviously Windows Explorer dies. Here is the header of the stream from the Wireshark dump (x.x.x.x) is the machines IP. GNUTELLA CONNECT/0.6 Listen-IP: x.x.x.x:8059 Remote-IP: 76.164.224.103 User-Agent: LimeWire/5.3.6 X-Requeries: false X-Ultrapeer: True X-Degree: 32 X-Query-Routing: 0.1 X-Ultrapeer-Query-Routing: 0.1 X-Max-TTL: 3 X-Dynamic-Querying: 0.1 X-Locale-Pref: en GGEP: 0.5 Bye-Packet: 0.1 GNUTELLA/0.6 200 OK Pong-Caching: 0.1 X-Ultrapeer-Needed: false Accept-Encoding: deflate X-Requeries: false X-Locale-Pref: en X-Guess: 0.1 X-Max-TTL: 3 Vendor-Message: 0.2 X-Ultrapeer-Query-Routing: 0.1 X-Query-Routing: 0.1 Listen-IP: 76.164.224.103:15649 X-Ext-Probes: 0.1 Remote-IP: x.x.x.x GGEP: 0.5 X-Dynamic-Querying: 0.1 X-Degree: 32 User-Agent: LimeWire/4.18.7 X-Ultrapeer: True X-Try-Ultrapeers: 121.54.32.36:3279,173.19.233.80:3714,65.182.97.15:5807,115.147.231.81:9751,72.134.30.181:15810,71.59.97.180:24295,74.76.84.250:25497,96.234.62.221:32344,69.44.246.38:42254,98.199.75.23:51230 GNUTELLA/0.6 200 OK So it seems that the malware has hooked into explorer.exe and hidden its self quite well as a Norton Scan doesn't pick anything up. I have looked in Windows firewall and it shouldn't be letting this traffic through. I have had a look into the messages explorer.exe is sending in Spy++ and the only related ones I can see are socket connections etc... My question is what can I do to look into this deeper? What does malware achieve by sending p2p traffic? I know to fix the problem the easiest way is to reinstall Windows but I want to get to the bottom of it first, just out of interest. Edit: Had a look at Deoendency Walker and Process Explorer. Both great tools. Here is a image of the TCP connections for explorer.exe in Process Explorer http://img210.imageshack.us/img210/3563/61930284.gif

  Read the article

• Looking for a AutoZoom browser plugin

  - by AngryHacker

  I have a pretty large 24" wide screen with a pretty high resolution. When I browse, some sites have a fixed layout and there is basically a narrow column. So I typically zoom in to the point just before the level where I have to scroll horizontally. Is there a browser plugin that auto-zooms in (or via a button or gesture or whatever) to the max available real estate? I'd prefer a plugin for Chrome, but Firefox will do too.

  Read the article

• samba 3.5 "force user" doesn't seem to be sticking

  - by myCubeIsMyCell

  After installing a new OS with newer version of samba, I'm having trouble accessing my shares. I can browse to the specific share, but only to the top level. As best I can tell from the logs, it seems the "force user" in the samba config isn't sticking beyond the initial connection. Details below. I installed a new version of CentOS on my storage server. My old CentOS (4?)install had samba version 3.0.33, new CentOS is using 3.5.10. No domain/AD involved ... just home workgroup. no real security... just some shares hidden & some defined as read-only. here's my config: [global] workgroup = WORKGROUP server string = Samba Server Version %v netbios name = luna security = share # logs split per machine log file = /var/log/samba/log.%m log level = 2 # max 50KB per log file, then rotate max log size = 50 winbind use default domain = Yes [strge] comment = please path = /storage browseable = yes read only = no force user = windowsguest force group = users guest ok = yes So... the problem I'm running into is that the 'force user' only seems to hold for the initial connection & I see all the top level folders fine. When I drill into a folder I get access denied - which appears to be due to my windows user info being sent (trys to authenticate xuser - a non-existant user to samba, so maps to nobody & fails). Here's the smb error msg: [2012/11/29 14:30:27.326195, 2] auth/auth.c:314(check_ntlm_password) check_ntlm_password: Authentication for user [xuser] -> [xuser] FAILED with error NT_STATUS_NO_SUCH_USER [2012/11/29 14:30:27.326251, 2] auth/auth.c:314(check_ntlm_password) check_ntlm_password: Authentication for user [nobody] -> [nobody] FAILED with error NT_STATUS_NO_SUCH_USER Most of the top level directories are 755, some 777. Either way, can not access them. If I do a chown -R windowsguest.users ... no change... but if I do a chmod -R to 777 or 755 they become browsable... but still can't create files (even for 777 ones). Not sure what role it plays if any... but had to recreate the user windowsguest under the new os install, uid & gid match old user. Seems the main issue as far as I can tell is that samba isn't maintaining the 'force user' - but I could be wildly off base. Client OS is win7 pro x64. Thanks for any suggestions or advice!

  Read the article

• Linux RAID-0 performance doesn't scale up over 1 GB/s

  - by wazoox

  I have trouble getting the max throughput out of my setup. The hardware is as follow : dual Quad-Core AMD Opteron(tm) Processor 2376 16 GB DDR2 ECC RAM dual Adaptec 52245 RAID controllers 48 1 TB SATA drives set up as 2 RAID-6 arrays (256KB stripe) + spares. Software : Plain vanilla 2.6.32.25 kernel, compiled for AMD-64, optimized for NUMA; Debian Lenny userland. benchmarks run : disktest, bonnie++, dd, etc. All give the same results. No discrepancy here. io scheduler used : noop. Yeah, no trick here. Up until now I basically assumed that striping (RAID 0) several physical devices should augment performance roughly linearly. However this is not the case here : each RAID array achieves about 780 MB/s write, sustained, and 1 GB/s read, sustained. writing to both RAID arrays simultaneously with two different processes gives 750 + 750 MB/s, and reading from both gives 1 + 1 GB/s. however when I stripe both arrays together, using either mdadm or lvm, the performance is about 850 MB/s writing and 1.4 GB/s reading. at least 30% less than expected! running two parallel writer or reader processes against the striped arrays doesn't enhance the figures, in fact it degrades performance even further. So what's happening here? Basically I ruled out bus or memory contention, because when I run dd on both drives simultaneously, aggregate write speed actually reach 1.5 GB/s and reading speed tops 2 GB/s. So it's not the PCIe bus. I suppose it's not the RAM. It's not the filesystem, because I get exactly the same numbers benchmarking against the raw device or using XFS. And I also get exactly the same performance using either LVM striping and md striping. What's wrong? What's preventing a process from going up to the max possible throughput? Is Linux striping defective? What other tests could I run?

  Read the article

• Any reason not to disable Windows kernel paging?

  - by Nathaniel

  So I'm planning on eventually going to 2 GB (mobo max) RAM from 1 GB, and I want to disable kernel paging once I do, because I've heard it can give a performance boost (and that I believe). Any reason not to do it or any general thoughts about it? Edit: for clarification, this is not disabling general RAM paging. This is disabling having kernel memory paged (or at least parts of it, as Charlls noted).

  Read the article

• How long do you keep log files?

  - by Alex

  I have an application which writes its log files in a special folder. Now I'd like to add a functionality to delete these logs after a defined period of time automatically. But how long should I keep the log files? What are "good" default values (7 or 180 days)? Or do you prefer other criteria (e.g. max. used disk space)?

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >