Search Results

Search found 12448 results on 498 pages for 'offline mode'.

Page 85/498 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• Cannot boot from K/Ubuntu install disk on my UEFI system

  - by user93241

  I just got a new system and have been trying to get it set up w/ Win7 & Kubuntu dual-boot, but I've got a major problem. The BIOS of my motherboard (an Asus Crosshair 990FX) is strictly UEFI -- there is no legacy support mode available. I've been reading up on how to get Kubuntu installed in UEFI mode but no matter what I try I cannot seem to even boot into my install CD/USB key properly. I can get as far as the selection screen ("Try Kubuntu", "Install Kubuntu"...) but this screen starts off not appearing correctly. If I try moving the cursor around it sometimes seems to correct itself and show me my choices. But once I select "Try Kubuntu" it starts loading, the screen goes black and then proceeds to flicker -- about once every 5-10 seconds or so. This continues indefinitely. I've tried this with both Kubuntu & Ubuntu installation media, even the AMD64+Mac Ubuntu variety that is supposed to be a lot more flexible w.r.t. UEFI. The only hint I've had that the system might have booted correctly is a little drum sound that plays when booting from the Ubuntu install disk. Well, that and the fact that when I hit my system's power button it seems to shut down correctly, even ejecting the CD at the end. This might be a video driver issue; my system has two nVidia 550's, one of which is attached to my primary monitor. (The secondary isn't hooked up yet.) I'll keep looking over similar questions but any advice would be greatly appreciated. UPDATE: I've tried booting into my 12.04 install CD twice now, each time using two different options supplied by my BIOS. One seemed to offer the ability to boot into my CD under UEFI mode -- this didn't even produce the initial boot menu. The other method offers the ability to boot into my CD NOT under UEFI mode. This DOES produce the boot menu, but after this point it seems I still cannot get to a proper video mode to see what's going on.

  Read the article

• Force SSRS 2008 to use SSRS 2005 CSV rendering

  - by Kash

  We are upgrading our report server from SSRS 2005 to SSRS 2008 R2. I have an issue with CSV export rendering for SSRS 2008 where the SUM of columns are appearing on the right side of the detail values in 2008 instead of the left side like in 2005 as shown in the below blocks. 117 and 131 are the sums of Column2 and Column3 respectively. SSRS 2005 CSV Output Column2_1,Column3_1,Column2,Column3 117,131,1,2 117,131,1,2 117,131,60,23 117,131,30,15 117,131,25,89 SSRS 2008 CSV Output Column2,Column3,Column2_1,Column3_1 1,2,117,131 1,2,117,131 60,23,117,131 30,15,117,131 25,89,117,131 I understand that the CSV renderer has gone through major changes in SSRS 2008 R2 with the support for charts and gauges and more importantly it provides 2 modes: the default Excel mode and Compliant mode. But neither mode helps fix this issue. The Compliant mode was supposed to be closest to that of 2005 but apparently it is not close enough for my case. My Question: Is there a way to force SSRS 2008 fall back a report to a backward compatibility mode so that it exports into a 2005 CSV format? Solution tried: a) Using 2005-based CRIs Based on this article on ExecutionLog2, if SSRS 2008 R2 encounters a report whose auto-upgrade is not possible (e.g. reports that were built with 2005-based CustomReportItem controls), those particular reports will be processed with the old Yukon engine in a "transparent backwards-compatibility mode". It seems like it falls back to its previous version mode (2005) and attempts to render it. So I tried using a 2005-based barcode CustomReportItem and deployed to a SSRS 2008 R2 report server, but it shows the same result as before though it suppressed the barcode. This would be because SSRS 2008 R2 finds a way to suppress part of the report output and displays the rest. It would be great to find a 2005-based CRI that makes SSRS 2008 R2 process it with its old Yukon engine. Please note that quite possibly, even if it uses the "old Yukon processing engine", it might still use the new CSV renderer hence it shows the same output. If that is true, then this option is moot. b) Using XML renderer We can use a custom XML renderer and then use XSLT to convert the xml to appropriate CSV but this would mean that we need to convert all our 200 reports. Hence this is not feasible. Please note that we do not have the option of having SSRS 2005 and SSRS 2008 R2 deployed side by side.

  Read the article

• How to import .ops file in Outlook 2007

  - by r0ca

  Hi all, I install ORK.exe on my Windows 7 machine to create a copy of my profile so I will have it as a template to push it to new user. So basically, I ran the Profile Wizard to create an .ops file. I saved it in my documents for the moment. Right now, I'm trying to import that file into my Outlook but I just can't figure it out! My goal is to have a profile template to push to new users when they log in for first time. Thanks a bunch in advance! EDIT: I just figured it out. But I have a problem: When I create my profile, Outlook 2007 on exchange was not in cache mode. So I created my profile with the Profile Wizard with cache mode disabled. I save my outlook.ops in My documents. Then, I enabled cache mode so when I will import my .ops file, it should be restore as cache mode disabled... But When I do that, cache mode is still checked (which I don't want to) Am I doing something wrong? I guess so but I just can't figure it out

  Read the article

• BIOS interrupts, privilege levels and paging

  - by Jack

  Hi, I was learning about Intel 8086-80486 CPUs and their interactions with HW. But I still don´t understand it quite well. Please, help me fill blank spots. First, I know that CPU communicates with HW using BIOS interrupts. But, what really happens in PC, when I call some INT instruction? I know that according the interrupt table some instructions begin to execute, but how by executing some instructions can BIOS recognize what I want to do? Becouse as far as I know, CPU has no extra communication channel with BIOS, it can only adress memory and receive data. So how can I instruct BIOS to do something, when I can only address RAM? Next thing I don't understand is about privilege levels. I know about ring model, and access rights, but how does the CPU know which privilege level has executed an instruction? I think that these privileges apply only when intruction is trying to address memory, but how does an application get its privilege level? I mean I know its level 3, but how is it set? And last thing, I know that paging is address scheme that is used to support aplication-transparent virtual memory, or swapping, but I could not find any information about how paging is tied with protected mode. Like if paging is like next mode independent of protected mode, or its somehow implemented within protected mode. And if it is implemented in protected mode, isn´t it too slow, to first address application space, then offset, and then paging folder, page and offset once again?

  Read the article

• BIOS interrupts, priviledge levels and paging

  - by Jack

  Hi, I was learning about Intel 8086-80486 CPUs and their interactions with HW. But I still don´t understand it quite well. Please, help me fill blank spots. First, I know that CPU communicates with HW using BIOS interrupts. But, what really happens in PC, when I call some INT instruction? I know that according the interrupt table some instructions begin to execute, but how by executing some instructions can BIOS recognize what I want to do? Becouse as far as I know, CPU has no extra communication channel with BIOS, it can only adress memory and receive data. So how can I instruct BIOS to do something, when I can only adress RAM? Next thing I dont understand is about priviledge levels. I know about ring model, and acess rights, but how CPU knows which priviledge level has executed instruction? I think that these priviledges apply only when intruction is trying to adress memory, but how applications gets its priviledge level? I mean I know its level 3, but how its set? And last thing, I know that paging is adress scheme that is used to support aplication-transparent virtual memory, or swaping, but I could not find any informations about how is paging tied with protected mode. Like if paging is like next mode independent of protectet mode, or its somehow implemented within protected mode. And if it is implemented in protected mode, isn´t it too slow, to first adress application space, than offset, and than paging folder, page and offset once again? Thank you for every response.

  Read the article

• ImgBurn fails to burn data CD-R disk due to "Layouts do not match" error

  - by 0xAether

  I have a reoccurring problem with the program ImgBurn. Whenever I try and burn anything to a CD-R using ImgBurn it burns just fine, except for when I go and verify the disk. It tells me that the "Layouts do not match". Windows 7 shows the disk as completely blank. Although, I see on the bottom of the disk it has been written to. I can burn ISO files to DVD-R's just fine. This only seems to happen with CD-R's. The CD-R's I'm using are Memorex Cool Colors 52x CD-R's. I have looked on Google, and it seems like I'm not the only one this happens to. Unfortunately, no one is able to provide an explanation. I have included the log file from the last CD I just burnt. If you need anything else to better diagnose this problem, I will gladly provide it. ; //****************************************\\ ; ImgBurn Version 2.5.7.0 - Log ; Monday, 19 November 2012, 16:11:57 ; \\****************************************// ; ; I 16:04:55 ImgBurn Version 2.5.7.0 started! I 16:04:55 Microsoft Windows 7 Ultimate x64 Edition (6.1, Build 7601 : Service Pack 1) I 16:04:55 Total Physical Memory: 4,156,380 KB - Available: 3,317,144 KB I 16:04:55 Initialising SPTI... I 16:04:55 Searching for SCSI / ATAPI devices... I 16:04:56 -> Drive 1 - Info: Optiarc DVD RW AD-7560S SH03 (D:) (SATA) I 16:04:56 Found 1 DVD±RW/RAM! I 16:05:37 Operation Started! I 16:05:37 Source File: C:\Users\Aaron\Desktop\VMware Workstation 9.iso I 16:05:37 Source File Sectors: 223,057 (MODE1/2048) I 16:05:37 Source File Size: 456,820,736 bytes I 16:05:37 Source File Volume Identifier: VMwareWorksta9 I 16:05:37 Source File Volume Set Identifier: 20121119_2102 I 16:05:37 Source File File System(s): ISO9660, Joliet I 16:05:37 Destination Device: [1:0:0] Optiarc DVD RW AD-7560S SH03 (D:) (SATA) I 16:05:37 Destination Media Type: CD-R (Disc ID: 97m17s06f, Moser Baer India) I 16:05:37 Destination Media Supported Write Speeds: 10x, 16x, 20x, 24x I 16:05:37 Destination Media Sectors: 359,847 I 16:05:37 Write Mode: CD I 16:05:37 Write Type: SAO I 16:05:37 Write Speed: 6x I 16:05:37 Lock Volume: Yes I 16:05:37 Test Mode: No I 16:05:37 OPC: No I 16:05:37 BURN-Proof: Enabled W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - MODE SENSE: 1,764 KB/s (10x), GET PERFORMANCE: 11,080 KB/s (63x) W 16:05:37 Write Speed Miscompare! - Wanted: 1,058 KB/s (6x), Got: 1,764 KB/s (10x) / 11,080 KB/s (63x) W 16:05:37 The drive only supports writing these discs at 10x, 16x, 20x, 24x. I 16:05:38 Filling Buffer... (80 MB) I 16:05:40 Writing LeadIn... I 16:06:07 Writing Session 1 of 1... (1 Track, LBA: 0 - 223056) I 16:06:07 Writing Track 1 of 1... (MODE1/2048, LBA: 0 - 223056) I 16:11:00 Synchronising Cache... I 16:11:18 Exporting Graph Data... I 16:11:18 Graph Data File: C:\Users\Aaron\AppData\Roaming\ImgBurn\Graph Data Files\Optiarc_DVD_RW_AD-7560S_SH03_MONDAY-NOVEMBER-19-2012_4-05_PM_97m17s06f_6x.ibg I 16:11:18 Export Successfully Completed! I 16:11:18 Operation Successfully Completed! - Duration: 00:05:41 I 16:11:18 Average Write Rate: 1,522 KB/s (10.1x) - Maximum Write Rate: 1,544 KB/s (10.3x) I 16:11:18 Cycling Tray before Verify... W 16:11:23 Waiting for device to become ready... I 16:11:47 Device Ready! E 16:11:47 CompareImageFileLayouts Failed! - Session Count Not Equal (1/0) E 16:11:47 Verify Failed! - Reason: Layouts do not match. I 16:11:57 Close Request Acknowledged I 16:11:57 Closing Down... I 16:11:57 Shutting down SPTI... I 16:11:57 ImgBurn closed!

  Read the article

• SGE: invoking qmake raises "critical error: can't resolve group"

  - by Pierre

  I'm new to SGE an I'm trying to run qmake with the simple following Makefile with our very new cluster: merge.txt: job1.txt job2.txt job3.txt ... cat $^ > $@ job1.txt: sleep 1 echo "Hello From " $@ > $@ sleep 1 job2.txt: sleep 2 echo "Hello From " $@ > $@ sleep 2 job3.txt: (...) the following command raises an error: qmake -l arch=lx24-amd64 -cwd -v PATH -- -j 4 sleep 1 dynamic mode sleep 2 dynamic mode sleep 3 dynamic mode sleep 4 dynamic mode critical error: can't resolve group qmake: *** [job3.txt] Error 1 critical error: can't resolve group qmake: *** [job2.txt] Error 1 critical error: can't resolve group qmake: *** [job1.txt] Error 1 critical error: can't resolve group what's wrong ?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• Two SATA HDDs connected using a Black Duet HDD Docking Station via eSATA to my Laptop, second drive

  - by leeand00

  Hi I am using a BlacX Duet HDD Docking Station to connect a 1TB WD Caviar Black SATA HDD (WD10000LSRTL) and a HITACHI SATA DESKSTAR (0S00163) to my G51VX (BestBuy) laptop via the eSATA port. When I plug in both HDDs in to the Docking Station, connect the docking station to my laptop and start Windows 7 (64-bit Ultimate), only the HDD in the first drive in the port actually shows up in My Computer and Disk Management. If I swap the drives positions I can get them both to work, but never at the same time. I also checked in the bios settings on the laptop, under Advanced-IDE Configuration-SATA Operation Mode, and it displays: SATA Operation Mode: [Enhanced] AHCI Port0 [Hard Disk] Device: Hard Disk Vendor: ST9320421AS LBA Mode: Supported S.M.A.R.T.: Supported AHCI Port5 [Hard Disk] Device: Hard Disk Vendor: Hitachi HDS721010CLA332 Size: 100.00 GB LBA Mode: Supported S.M.A.R.T.: Supported There should be a third drive, but I'm not certain why it is not being picked up. Additionally, before I played around with the settings in the IDE configuration, it used to display the DVD as well.

  Read the article

• Linux - Only first virtual interface can ping external gateway

  - by husvar

  I created 3 virtual interfaces with different mac addresses all linked to the same physical interface. I see that they successfully arp for the gw and they can ping (the request is coming in the packet capture in wireshark). However the ping utility does not count the responses. Does anyone knows the issue? I am running Ubuntu 14.04 in a VmWare. root@ubuntu:~# ip link sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip addr sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:febc:fc8b/64 scope link valid_lft forever preferred_lft forever root@ubuntu:~# ip route sh root@ubuntu:~# ip link add link eth0 eth0.1 addr 00:00:00:00:00:11 type macvlan root@ubuntu:~# ip link add link eth0 eth0.2 addr 00:00:00:00:00:22 type macvlan root@ubuntu:~# ip link add link eth0 eth0.3 addr 00:00:00:00:00:33 type macvlan root@ubuntu:~# ip -4 link sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff 18: eth0.1@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/ether 00:00:00:00:00:11 brd ff:ff:ff:ff:ff:ff 19: eth0.2@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/ether 00:00:00:00:00:22 brd ff:ff:ff:ff:ff:ff 20: eth0.3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/ether 00:00:00:00:00:33 brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip -4 addr sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever root@ubuntu:~# ip -4 route sh root@ubuntu:~# dhclient -v eth0.1 Internet Systems Consortium DHCP Client 4.2.4 Copyright 2004-2012 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0.1/00:00:00:00:00:11 Sending on LPF/eth0.1/00:00:00:00:00:11 Sending on Socket/fallback DHCPDISCOVER on eth0.1 to 255.255.255.255 port 67 interval 3 (xid=0x568eac05) DHCPREQUEST of 192.168.1.145 on eth0.1 to 255.255.255.255 port 67 (xid=0x568eac05) DHCPOFFER of 192.168.1.145 from 192.168.1.254 DHCPACK of 192.168.1.145 from 192.168.1.254 bound to 192.168.1.145 -- renewal in 1473 seconds. root@ubuntu:~# dhclient -v eth0.2 Internet Systems Consortium DHCP Client 4.2.4 Copyright 2004-2012 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0.2/00:00:00:00:00:22 Sending on LPF/eth0.2/00:00:00:00:00:22 Sending on Socket/fallback DHCPDISCOVER on eth0.2 to 255.255.255.255 port 67 interval 3 (xid=0x21e3114e) DHCPREQUEST of 192.168.1.146 on eth0.2 to 255.255.255.255 port 67 (xid=0x21e3114e) DHCPOFFER of 192.168.1.146 from 192.168.1.254 DHCPACK of 192.168.1.146 from 192.168.1.254 bound to 192.168.1.146 -- renewal in 1366 seconds. root@ubuntu:~# dhclient -v eth0.3 Internet Systems Consortium DHCP Client 4.2.4 Copyright 2004-2012 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0.3/00:00:00:00:00:33 Sending on LPF/eth0.3/00:00:00:00:00:33 Sending on Socket/fallback DHCPDISCOVER on eth0.3 to 255.255.255.255 port 67 interval 3 (xid=0x11dc5f03) DHCPREQUEST of 192.168.1.147 on eth0.3 to 255.255.255.255 port 67 (xid=0x11dc5f03) DHCPOFFER of 192.168.1.147 from 192.168.1.254 DHCPACK of 192.168.1.147 from 192.168.1.254 bound to 192.168.1.147 -- renewal in 1657 seconds. root@ubuntu:~# ip -4 link sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff 18: eth0.1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default link/ether 00:00:00:00:00:11 brd ff:ff:ff:ff:ff:ff 19: eth0.2@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default link/ether 00:00:00:00:00:22 brd ff:ff:ff:ff:ff:ff 20: eth0.3@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default link/ether 00:00:00:00:00:33 brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip -4 addr sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 18: eth0.1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default inet 192.168.1.145/24 brd 192.168.1.255 scope global eth0.1 valid_lft forever preferred_lft forever 19: eth0.2@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default inet 192.168.1.146/24 brd 192.168.1.255 scope global eth0.2 valid_lft forever preferred_lft forever 20: eth0.3@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default inet 192.168.1.147/24 brd 192.168.1.255 scope global eth0.3 valid_lft forever preferred_lft forever root@ubuntu:~# ip -4 route sh default via 192.168.1.254 dev eth0.1 192.168.1.0/24 dev eth0.1 proto kernel scope link src 192.168.1.145 192.168.1.0/24 dev eth0.2 proto kernel scope link src 192.168.1.146 192.168.1.0/24 dev eth0.3 proto kernel scope link src 192.168.1.147 root@ubuntu:~# arping -c 5 -I eth0.1 192.168.1.254 ARPING 192.168.1.254 from 192.168.1.145 eth0.1 Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 6.936ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.986ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 0.654ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 5.137ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.426ms Sent 5 probes (1 broadcast(s)) Received 5 response(s) root@ubuntu:~# arping -c 5 -I eth0.2 192.168.1.254 ARPING 192.168.1.254 from 192.168.1.146 eth0.2 Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 5.665ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 3.753ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 16.500ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 3.287ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 32.438ms Sent 5 probes (1 broadcast(s)) Received 5 response(s) root@ubuntu:~# arping -c 5 -I eth0.3 192.168.1.254 ARPING 192.168.1.254 from 192.168.1.147 eth0.3 Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 4.422ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.429ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.321ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 40.423ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.268ms Sent 5 probes (1 broadcast(s)) Received 5 response(s) root@ubuntu:~# tcpdump -n -i eth0.1 -v & [1] 5317 root@ubuntu:~# ping -c5 -q -I eth0.1 192.168.1.254 PING 192.168.1.254 (192.168.1.254) from 192.168.1.145 eth0.1: 56(84) bytes of data. tcpdump: listening on eth0.1, link-type EN10MB (Ethernet), capture size 65535 bytes 13:18:37.612558 IP (tos 0x0, ttl 64, id 2595, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.145 > 192.168.1.254: ICMP echo request, id 5318, seq 2, length 64 13:18:37.618864 IP (tos 0x68, ttl 64, id 14493, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.145: ICMP echo reply, id 5318, seq 2, length 64 13:18:37.743650 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:38.134997 IP (tos 0x0, ttl 128, id 23547, offset 0, flags [none], proto UDP (17), length 229) 192.168.1.86.138 > 192.168.1.255.138: NBT UDP PACKET(138) 13:18:38.614580 IP (tos 0x0, ttl 64, id 2596, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.145 > 192.168.1.254: ICMP echo request, id 5318, seq 3, length 64 13:18:38.793479 IP (tos 0x68, ttl 64, id 14495, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.145: ICMP echo reply, id 5318, seq 3, length 64 13:18:39.151282 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:39.615612 IP (tos 0x0, ttl 64, id 2597, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.145 > 192.168.1.254: ICMP echo request, id 5318, seq 4, length 64 13:18:39.746981 IP (tos 0x68, ttl 64, id 14496, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.145: ICMP echo reply, id 5318, seq 4, length 64 --- 192.168.1.254 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4008ms rtt min/avg/max/mdev = 2.793/67.810/178.934/73.108 ms root@ubuntu:~# killall tcpdump >> /dev/null 2>&1 9 packets captured 12 packets received by filter 0 packets dropped by kernel [1]+ Done tcpdump -n -i eth0.1 -v root@ubuntu:~# tcpdump -n -i eth0.2 -v & [1] 5320 root@ubuntu:~# ping -c5 -q -I eth0.2 192.168.1.254 PING 192.168.1.254 (192.168.1.254) from 192.168.1.146 eth0.2: 56(84) bytes of data. tcpdump: listening on eth0.2, link-type EN10MB (Ethernet), capture size 65535 bytes 13:18:41.536874 ARP, Ethernet (len 6), IPv4 (len 4), Reply 192.168.1.254 is-at 58:98:35:57:a0:70, length 46 13:18:41.536933 IP (tos 0x0, ttl 64, id 2599, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 1, length 64 13:18:41.539255 IP (tos 0x68, ttl 64, id 14507, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 1, length 64 13:18:42.127715 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:42.511725 IP (tos 0x0, ttl 64, id 2600, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 2, length 64 13:18:42.514385 IP (tos 0x68, ttl 64, id 14527, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 2, length 64 13:18:42.743856 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:43.511727 IP (tos 0x0, ttl 64, id 2601, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 3, length 64 13:18:43.513768 IP (tos 0x68, ttl 64, id 14528, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 3, length 64 13:18:43.637598 IP (tos 0x0, ttl 128, id 23551, offset 0, flags [none], proto UDP (17), length 225) 192.168.1.86.17500 > 255.255.255.255.17500: UDP, length 197 13:18:43.641185 IP (tos 0x0, ttl 128, id 23552, offset 0, flags [none], proto UDP (17), length 225) 192.168.1.86.17500 > 192.168.1.255.17500: UDP, length 197 13:18:43.641201 IP (tos 0x0, ttl 128, id 23553, offset 0, flags [none], proto UDP (17), length 225) 192.168.1.86.17500 > 255.255.255.255.17500: UDP, length 197 13:18:43.743890 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:44.510758 IP (tos 0x0, ttl 64, id 2602, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 4, length 64 13:18:44.512892 IP (tos 0x68, ttl 64, id 14538, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 4, length 64 13:18:45.510794 IP (tos 0x0, ttl 64, id 2603, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 5, length 64 13:18:45.519701 IP (tos 0x68, ttl 64, id 14539, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 5, length 64 13:18:49.287554 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:50.013463 IP (tos 0x0, ttl 255, id 50737, offset 0, flags [DF], proto UDP (17), length 73) 192.168.1.146.5353 > 224.0.0.251.5353: 0 [2q] PTR (QM)? _ipps._tcp.local. PTR (QM)? _ipp._tcp.local. (45) 13:18:50.218874 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:51.129961 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:52.197074 IP6 (hlim 255, next-header UDP (17) payload length: 53) 2001:818:d812:da00:200:ff:fe00:22.5353 > ff02::fb.5353: [udp sum ok] 0 [2q] PTR (QM)? _ipps._tcp.local. PTR (QM)? _ipp._tcp.local. (45) 13:18:54.128240 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 --- 192.168.1.254 ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4000ms root@ubuntu:~# killall tcpdump >> /dev/null 2>&1 13:18:54.657731 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:54.743174 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 25 packets captured 26 packets received by filter 0 packets dropped by kernel [1]+ Done tcpdump -n -i eth0.2 -v root@ubuntu:~# tcpdump -n -i eth0.3 icmp & [1] 5324 root@ubuntu:~# ping -c5 -q -I eth0.3 192.168.1.254 PING 192.168.1.254 (192.168.1.254) from 192.168.1.147 eth0.3: 56(84) bytes of data. tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0.3, link-type EN10MB (Ethernet), capture size 65535 bytes 13:18:56.373434 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 1, length 64 13:18:57.372116 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 2, length 64 13:18:57.381263 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 2, length 64 13:18:58.371141 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 3, length 64 13:18:58.373275 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 3, length 64 13:18:59.371165 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 4, length 64 13:18:59.373259 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 4, length 64 13:19:00.371211 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 5, length 64 13:19:00.373278 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 5, length 64 --- 192.168.1.254 ping statistics --- 5 packets transmitted, 1 received, 80% packet loss, time 4001ms rtt min/avg/max/mdev = 13.666/13.666/13.666/0.000 ms root@ubuntu:~# killall tcpdump >> /dev/null 2>&1 9 packets captured 10 packets received by filter 0 packets dropped by kernel [1]+ Done tcpdump -n -i eth0.3 icmp root@ubuntu:~# arp -n Address HWtype HWaddress Flags Mask Iface 192.168.1.254 ether 58:98:35:57:a0:70 C eth0.1 192.168.1.254 ether 58:98:35:57:a0:70 C eth0.2 192.168.1.254 ether 58:98:35:57:a0:70 C eth0.3

  Read the article

• Word 2007 files on emacs?

  - by Paul Nathan

  Is there a word-2007 mode for emacs?

  Read the article

• How to specify file permission when putting a file using OpenSSH sftp command

  - by Adi Roiban

  I am using various SFTP clients for uploading files to an SFTP server and I have a problem with default permission used when putting files. When requesting to put a file, SFTP client like WinSCP or Filezilla will send the SSH_OPEN command without requesting any explicit file permission. On the other side, it looks like the OpenSSH sftp command on Linux (Red Hat and Ubuntu) is pending the SSH_OPEN command together with the '640' mode. How can I configure the OpenSSH command to not explictly set the file mode or how can I configure it to send a mode, other than 640? Many thanks! Update: I checked the OpenSSH sftp client source code and it looks like OpenSSH sftp will always tries to preserve file mode even if -P is not set: http://www.koders.com/c/fidD3B20680F615B33ACCB42398FAAFEE1C007DF942.aspx?s=rsa#L986 To solve this problem I used Putty SFTP client.

  Read the article

• Windows 7: Computer does not enter automatic standby

  - by heinzi

  My Windows 7 PC is set to automatically enter standby ("sleep mode") after 30 minutes. For some reason it stopped working a few days ago (it keeps on running). Is there some systematic way to determine what is preventing the system from automatically entering sleep mode after the designated idle time? Manually sending the machine to sleep works fine. The monitor also enters power save mode automatically, so the "idling detection" of Windows seems to work fine.

  Read the article

• gVIM "put" driving me mad, how do I "put" at the beginning of a line

  - by crgnz

  I'm learning gVIM on Windows, and as I slowly learn more of the keystrokes I find myself using the mouse less and less, which is great. I have a couple of questions I've yet to figure out: I do a lot of copy and paste. So I use 'v' to enter VISUAL mode, use k/j to move up/down and select the lines, then hit 'y' to yank. I then go to the line where I want to insert, and hit 'p' to put, BUT the darn thing pastes after the 1st character. I can't move any further left, so I am definitely at the start of the line, so I find the 'p'ut behaviour of pasting 1 char after my cursor position to be supremely annoying. I switch between edit and command mode an awful lot, and my poor little finger on my left hand is getting sore from being stretched out to hit the 'Esc' key (to enter command mode) every few seconds. Is there a more finger-friendly way to enter command mode?

  Read the article

• Mac OS X L2TP VPN won't connect

  - by smokris

  I'm running Mac OS X Server 10.6, providing an L2TP VPN service. The VPN works just fine when connecting from all computers except one --- this one computer stays at the "Connecting..." stage for a while, then says "The L2TP-VPN server did not respond". In the console, I see this: 6/7/10 10:48:07 AM pppd[341] pppd 2.4.2 (Apple version 412.0.10) started by jdoe, uid 503 6/7/10 10:48:07 AM pppd[341] L2TP connecting to server 'foo.bar.baz.edu' (256.256.256.256)... 6/7/10 10:48:07 AM pppd[341] IPSec connection started 6/7/10 10:48:07 AM racoon[342] Connecting. 6/7/10 10:48:07 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 1). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 2). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 3). 6/7/10 10:48:08 AM racoon[342] IKE Packet: receive success. (Initiator, Main-Mode message 4). 6/7/10 10:48:08 AM racoon[342] IKE Packet: transmit success. (Initiator, Main-Mode message 5). 6/7/10 10:48:11 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:14 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). 6/7/10 10:48:17 AM racoon[342] IKE Packet: transmit success. (Phase1 Retransmit). ...and the "retransmit" messages continue until the error message pops up. So far I've unsuccessfully tried: rebooting deleting the VPN profile and recreating it verifying the client's internet connection (it is able to reach the VPN server) connecting through several different networks (in case a router was blocking VPN packets) disabling the Mac OS X Firewall on the client making sure that the VPN settings exactly match those of other working computers running software update (the client is on 10.6.3) Any ideas?

  Read the article

• Linux NIC Bonding Issue (CentOS 4 / RHEL 3)

  - by jinanwow

  I am having an issue with bonding NICs on CentOS 4. It appears the bonding driver does work, but it is stuck in round-robin mode and I am trying to get to active-backup. The current config is: ifcfg-bond0 DEVICE=bond0 IPADDR=192.168.204.18 NETMASK=255.255.255.0 ONBOOT=yes BOOTPROTO=none USERCTL=no TYPE=Bonding BONDING_OPTS="mode=1 miimon=100" ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none ONBOOT=yes TYPE=Ethernet MASTER=bond0 SLAVE=yes ifcfg-eth3 DEVICE=eth3 ONBOOT=yes BOOTPROTO=none TYPE=Ethernet MASTER=bond0 SLAVE=yes cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v2.6.3-rh (June 8, 2005) Bonding Mode: load balancing (round-robin) MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:17:a4:8f:94:b1 Slave Interface: eth3 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:1b:21:56:b8:69 cat /etc/modprobe.conf alias eth0 tg3 alias eth1 tg3 alias eth3 e1000 alias eth2 e1000 alias bond0 bonding options bond0 mode=1 miimon=100 I have tried moving the bonding information out of the ifcfg-bond0 into the modprobe configuration file. It seems that it is stuck in RR and I am trying to get it into the Active-backup (mode 1) state. Any ideas what would be causing this issue?

  Read the article

• Is it possible to manually specify an alternative Procfile on Heroku?

  - by BillyBBone

  I have a repository which can be deployed in two modes: one is a front-end web application, while the other is a data manipulating process which runs non-stop, 24x7. The application runs on Django and connects to a Postgres database. For architectural reasons that I won't go into, I'd like to deploy the app in front-end mode inside as one Heroku application, and deploy the same app (i.e. the same git repo) in the data agent mode, as another Heroku application. Both applications will share the same Postgres connection string, and thus the data agent will feed the front-end app. Is it possible to maintain two separate Procfiles in one repo? This would cause the 3 appropriate dynos to start in front-end mode, and would spin up another process entirely in the other mode.

  Read the article

• Unable to activate Windows XP

  - by Josh Kelley

  The latest round of Patch Tuesday updates left my Windows XP computer unbootable. ("Fatal System Error: The Windows Logon Process system process terminated unexpectedly.") After much messing around with the recovery console, an XP CD's repair mode, and manually copying registry files around, I have a system that can boot again. However, I overwrote my OEM XP installation's activation information while trying to run a retail XP CD's setup, so it needs reactivation. Here's my problem: I cannot activate it at all. I log in, Windows tells me I have to activate to continue, I click Yes, and absolutely nothing happens: no windows, no response to keyboard or mouse, no response to Ctrl-Alt-Del, nothing. Safe mode works, but I can't activate in safe mode (EDIT: not even safe mode with networking). I read a trick online of pressing [Windows Key]+U to bring up the Microsoft Narrator, and that works, but clicking its Microsoft Web Site link does nothing. My last attempt to resolve this was to reinstall Windows off of the OEM CD. Now I have two parallel Windows installations, both on the same hard drive, one with all of my stuff and no way to activate it, one fully activated with no usable programs. Any ideas? Any way to activate in safe mode? Any way to copy activation information from my activated installation to my unactivated installation (since they're both on the same hard drive)?

  Read the article

• Sustaining Dual Channel among many RAM modules

  - by Odys

  I'd like to know what are the factors that need to be set in order to sustain the Dual Channel mode. In a mobo with 4 DDR3 slots: Do I have to put pair of chips? Eg: If I put 3 identical chips only, will I have Dual channel or not? If I put 4 Ram chips that aren't from of same ventor/model, will I have the same latency among them (the highest of all)? Also, will I sustain Dual Channel mode? If one Ram has max frequency of 1033 and the other 3 chips are of 1300, will I have 1033Mhz for all chips and Dual Channel mode on? What if I put 2x4Gb and 2x8Gb chips (latency, Dual Channel)? Can I put 4Gb chips in slots 1 and 3 and 8Gb in slots 2 and 4 and still have dual channel mode enabled? (Some of the questions might sound silly but their answers aren't that clear to me) (Also, assume that there aren't any bottlenecks because of other parts on the system)

  Read the article

• Misconfigured external monitor on Mac OS X Snow Leopard 10.6.3

  - by Mike

  I have an external monitor (specifically, an HDTV) hooked up to my 2.53GHz 13" macbook pro. This display works fine and I use it with my mac in clamshell mode (eg. with an external keyboard/mouse and the laptop closed and the built-in mac screen turned off) My Mac has multiple users on it. For User A I can use the mac with the external monitor in both clamshell and dual-monitor setups. For User B, I can use the monitor in a dual-monitor setup, but whenever I switch to clamshell mode the Mac switches to an incorrect output resolution or frequency setting that my HDTV doesn't recognize, resulting in a blank screen and a message about Unsupported Resolution. Chances are I did this to myself by misconfiguring my display settings at some point in the past, but I have no idea how to undo it. I (obviously) can't seen the display to change the settings when it's borked. I can see the display settings if I switch to Dual-monitor mode, but those settings only affect the dual monitor setup; no matter how I change the settings in dual-monitor mode, the clamshell mode setup remains borked. How can I dig myself out of this hole?

  Read the article

• How to reset password for Dell PowerConnect 2708?

  - by oherrala

  I do as the user manual says and press "Managed Mode" button to get into unmanaged mode and then press "Managed Mode" button again for managed mode. This should reset the device to factory defaults and username "Admin" with no password. However, the device resets (I think) and I can access the web console from IP 192.168.2.1, but the username and password doesn't work. Maybe the device doesn't reset after all. Or the username/password has been changed in some firmware upgrade? What should I do to get into management of this switch?

  Read the article

• Thunderbird feed not found

  - by poru

  Hello, I'm using Thunderbird as my feedreader, but a lot of my long feed list is partially offline. Is there a addon or something similar to find that offline feeds und delete them from my feed-list?

  Read the article

• Mavericks not booting after successful installation over Lion (10.7.5)

  - by rpatil

  On my 2012 MacBook Pro (15 inch, non retina, i7, 10GB RAM) after successful installation when Mavericks tried to boot, it is freezing there with "Still waiting for root device" (Seen Using CMD + V during boot). Someone please help. My Mac is not usable anymore. Boots in safe mode but freezes in safe mode too. From safe mode reinstalled Mavericks but failed again with same error. If it can't be fixed please let me know if it can be reverted.

  Read the article

• Dell Optiplex GX620 > windows xp home addition OU7670

  - by Ren D

  My question is my Dell Optiplex 620 is not working properly !! when i turn it on it goes automaticaly to bios and says click on safe mode or safe network or best last start up or normal mode ?? but when i click on normal it comes back to that window then i click on safe mode and it works for about 5 min then it reboots its self every time what can i do ? i checked if there was a virus and its clean !! please help

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >