Search Results

Search found 5367 results on 215 pages for 'outlook express'.

Page 85/215 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

  • WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

    - by el10780
    After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

    Read the article

  • Ubuntu 12.04 wireless (wifi) not working, can not upgrade to 12.10, touchpad gestures not working. What to do?

    - by Ritwik
    I installed ubuntu 12.04 LTS 3 days ago and since then wireless feature and touchpad gestures are not working. Tried everything on internet but still unsuccessful. I cant upgrade to ubuntu 12.10. These are the following comments I tried. Please help me. EDIT: just realized usb 3.0 is also not working. COMMAND lsb_release -r OUTPUT ----------------------------------------------------------------- Release: 12.04 ----------------------------------------------------------------- COMMAND lspci OUTPUT ------------------------------------------------------------------ 00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) 00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) 00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) 00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) 00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) 00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05) 07:00.0 3D controller: NVIDIA Corporation GF117M [GeForce 610M/710M / GT 620M/625M/630M/720M] (rev a1) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 07) 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01) 0f:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01) ------------------------------------------------------------------ COMMAND sudo apt-get install linux-backports-modules-wireless-lucid-generic OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-backports-modules-wireless-lucid-generic ------------------------------------------------------------------- COMMAND cat /etc/lsb-release; uname -a OUTPUT ------------------------------------------------------------------- DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.5 LTS" Linux ritwik-PC 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux ------------------------------------------------------------------- COMMAND lspci -nnk | grep -iA2 net OUTPUT ------------------------------------------------------------------- 08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 07) Subsystem: Hewlett-Packard Company Device [103c:225d] Kernel driver in use: r8169 -- 0f:00.0 Network controller [0280]: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter [168c:0036] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:217f] ------------------------------------------------------------------- COMMAND lsusb OUTPUT ------------------------------------------------------------------- Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:8008 Intel Corp. Bus 002 Device 002: ID 8087:8000 Intel Corp. ------------------------------------------------------------------- COMMAND iwconfig OUTPUT ------------------------------------------------------------------- lo no wireless extensions. eth0 no wireless extensions. ------------------------------------------------------------------- COMMAND rfkill list all OUTPUT ------------------------------------------------------------------- 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no ------------------------------------------------------------------- COMMAND lsmod OUTPUT ------------------------------------------------------------------- Module Size Used by snd_hda_codec_realtek 224215 1 bnep 18281 2 rfcomm 47604 0 bluetooth 180113 10 bnep,rfcomm parport_pc 32866 0 ppdev 17113 0 nls_iso8859_1 12713 1 nls_cp437 16991 1 vfat 17585 1 fat 61512 1 vfat snd_hda_intel 33719 3 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 17764 1 snd_hda_codec snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event nouveau 775039 0 joydev 17693 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq ttm 76949 1 nouveau uvcvideo 72627 0 snd 79041 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device videodev 98259 1 uvcvideo drm_kms_helper 46978 1 nouveau psmouse 98051 0 drm 241971 3 nouveau,ttm,drm_kms_helper i2c_algo_bit 13423 1 nouveau soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm v4l2_compat_ioctl32 17128 1 videodev hp_wmi 18092 0 serio_raw 13211 0 sparse_keymap 13890 1 hp_wmi mxm_wmi 13021 1 nouveau video 19651 1 nouveau wmi 19256 2 hp_wmi,mxm_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62190 0 ------------------------------------------------------------------- COMMAND sudo su modprobe -v ath9k OUTPUT ------------------------------------------------------------------- insmod /lib/modules/3.2.0-67-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko insmod /lib/modules/3.2.0-67-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.2.0-67-generic/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko ------------------------------------------------------------------- COMMAND do-release-upgrade OUTPUT ------------------------------------------------------------------- Err Upgrade tool signature 404 Not Found [IP: 91.189.88.149 80] Err Upgrade tool 404 Not Found [IP: 91.189.88.149 80] Fetched 0 B in 0s (0 B/s) WARNING:root:file 'quantal.tar.gz.gpg' missing Failed to fetch Fetching the upgrade failed. There may be a network problem. ------------------------------------------------------------------- COMMAND sudo modprobe ath9k dmesg | grep ath9k NO OUTPUT FOR THEM COMMAND dmesg | grep -e ath -e 80211 OUTPUT ------------------------------------------------------------------- [ 13.232372] type=1400 audit(1408867538.399:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=975 comm="apparmor_parser" [ 13.232615] type=1400 audit(1408867538.399:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=975 comm="apparmor_parser" [ 15.186599] ath3k: probe of 3-4:1.0 failed with error -110 [ 15.186635] usbcore: registered new interface driver ath3k [ 88.219329] cfg80211: Calling CRDA to update world regulatory domain [ 88.351665] cfg80211: World regulatory domain updated: [ 88.351667] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 88.351670] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351671] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351673] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 88.351674] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 88.351675] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------------------- COMMAND sudo apt-get install touchpad-indicator OUTPUT ------------------------------------------------------------------- Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: gir1.2-gconf-2.0 python-pyudev Suggested packages: python-qt4 python-pyside.qtcore The following NEW packages will be installed: gir1.2-gconf-2.0 python-pyudev touchpad-indicator 0 upgraded, 3 newly installed, 0 to remove and 0 not upgraded. Need to get 84.1 kB of archives. After this operation, 1,136 kB of additional disk space will be used. Do you want to continue [Y/n]? Y Get:1 http://ppa.launchpad.net/atareao/atareao/ubuntu/ precise/main touchpad-indicator all 0.9.3.12-1ubuntu1 [46.5 kB] Get:2 http://archive.ubuntu.com/ubuntu/ precise/main gir1.2-gconf-2.0 amd64 3.2.5-0ubuntu2 [7,098 B] Get:3 http://archive.ubuntu.com/ubuntu/ precise/main python-pyudev all 0.13-1 [30.5 kB] Fetched 84.1 kB in 2s (31.6 kB/s) Selecting previously unselected package gir1.2-gconf-2.0. (Reading database ... 169322 files and directories currently installed.) Unpacking gir1.2-gconf-2.0 (from .../gir1.2-gconf-2.0_3.2.5-0ubuntu2_amd64.deb) ... Selecting previously unselected package python-pyudev. Unpacking python-pyudev (from .../python-pyudev_0.13-1_all.deb) ... Selecting previously unselected package touchpad-indicator. Unpacking touchpad-indicator (from .../touchpad-indicator_0.9.3.12-1ubuntu1_all.deb) ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for desktop-file-utils ... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for software-center ... INFO:softwarecenter.db.update:no translation information in database needed Setting up gir1.2-gconf-2.0 (3.2.5-0ubuntu2) ... Setting up python-pyudev (0.13-1) ... Setting up touchpad-indicator (0.9.3.12-1ubuntu1) ... ------------------------------------------------------------------- Not able to find ( drivers/net/wireless/ath/ath9k/hw.c ) or ( drivers/net/wireless/ath/ath9k/hw.h )

    Read the article

  • Wireless drivers

    - by Kencer
    The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

    Read the article

  • .NET vs Windows 8: Rematch!

    - by Simon Cooper
    So, although you will be able to use your existing .NET skills to develop Metro apps, it turns out Microsoft are limiting Visual Studio 2011 Express to Metro-only. From the Express website: Visual Studio 11 Express for Windows 8 provides tools for Metro style app development. To create desktop apps, you need to use Visual Studio 11 Professional, or higher. Oh dear. To develop any sort of non-Metro application, you will need to pay for at least VS Professional. I suspect Microsoft (or at least, certain groups within Microsoft) have a very explicit strategy in mind. By making VS Express Metro-only, developers who don't want to pay for Professional will be forced to make their simple one-shot or open-source application in Metro. This increases the number of applications available for Windows 8 and Windows mobile devices, which in turn make those platforms more attractive for consumers. When you use the free VS 11 Express, instead of paying Microsoft, you provide them a service by making applications for Metro, which in turn makes Microsoft's mobile offering more attractive to consumers, increasing their market share. Of course, it remains to be seen if developers forced to jump onto the Metro bandwagon will simply jump ship to Android or iOS instead. At least, that's what I think is going on. With Microsoft, who really knows?

    Read the article

  • Managing MS Exchange server-side email rules on Mac OS X?

    - by Doug Harris
    Has anybody found an easy way to manage server-side rules from Mac OS X? Here's a brief list of what I know doesn't work: Entourage 2008 - it supports client rules, but not server rules. No good, there are certain actions that should happen before I open my laptop or check my email on my iPhone. Apple Mail - same as Entourage, but at least I don't get as frustrated since, unlike Entourage, this isn't a Microsoft product. Web mail (aka Outlook Web Access) - perhaps you can manage rule in the fancy version which Exchange serves to IE, but not with the browsers available on a Mac. I manage this now by launching a VMWare virtual machine running Windows XP and Outlook. I don't count that as an easy way. Update, post release of Office 2011 Does MS Outlook 2011 have the ability to manage server-side rules? Update, post installation of Office 2011 No. Outlook 2011 doesn't have this ability. I've already removed my account from Outlook and switched back to Apple Mail and iCal

    Read the article

  • SQL Server Express 2005 and Vista x64 Home Preminum - How do I do a clean install?

    - by gemeye
    The install for SQLSRVREXP 2005, for Vista x 64 its SQLEXPR_ADV.EXE downloaded from http://www.microsoft.com/downloads/en/confirmation.aspx?familyId=b448b0d0-ee79-48f6-b50a-7c4f028c2e3d&displayLang=en The first part of the installation is an analysis of the computer's configuration. There was one warning. Opening the details shows: ASP.Net Version Registration Requirement (Warning) Messages ASP.Net Version Registration Requirement Failed to find the ASP.Net Version Registration with Microsoft Internet Information Services (IIS) Anyone have any idea how to clear this up? What is the ASP.Net Version Registration wiht Microsoft IIS mean? And how would I fix this? Thank you in advance.

    Read the article

  • ubuntu 10.04: wlan0 No such device

    - by AodhanOL
    I am using a Dell xps l702x and I am using ubuntu 10.04 because I need to use f77 (don't ask) and I wasn't able to get it working on later versions of ubuntu. I cannot use the wifi at all. I have tried to fix it and have had limited success (changed the output from rfkill list all from Hard blocked: yes, to hard blocked: no). Here is the output from rfkill list all aodhan@aodhan-laptop:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-bluetooth: Bluetooth Soft blocked: no Hard blocked: no Here is the output from iwconfig: aodhan@aodhan-laptop:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. pan0 no wireless extensions. And here is the output from ifconfig -a: aodhan@aodhan-laptop:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 5c:f9:dd:3d:f2:f7 inet addr:192.168.1.17 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::5ef9:ddff:fe3d:f2f7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3417 errors:0 dropped:0 overruns:0 frame:0 TX packets:2894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3317567 (3.3 MB) TX bytes:505049 (505.0 KB) Interrupt:30 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 7e:7e:e8:39:70:af BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And finally, the output from lspci: 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1246 (rev a1) 03:00.0 Network controller: Intel Corporation Device 008a (rev 34) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Please help me! Thank you in advance. Edit: Further info - this is a dual install with a windows 7 system as the other option. However, I can't access that until tomorrow (I won't have access to the windows 7 disc until then, and grub isn't letting me load it). Therefore, I can't be sure whether it still works on that or not. It used to, though.

    Read the article

  • How do you stop a user-instance of Sql Server? (Sql Express user instance database files locked, eve

    - by Bittercoder
    When using SQL Server Express 2005's User Instance feature with a connection string like this: <add name="Default" connectionString="Data Source=.\SQLExpress; AttachDbFilename=C:\My App\Data\MyApp.mdf; Initial Catalog=MyApp; User Instance=True; MultipleActiveResultSets=true; Trusted_Connection=Yes;" /> We find that we can't copy the database files MyApp.mdf and MyApp_Log.ldf (because they're locked) even after stopping the SqlExpress service, and have to resort to setting the SqlExpress service from automatic to manual startup mode, and then restarting the machine, before we can then copy the files. It was my understanding that stopping the SqlExpress service should stop all the user instances as well, which should release the locks on those files. But this does not seem to be the case - could anyone shed some light on how to stop a user instance, such that it's database files are no longer locked? Update OK, I stopped being lazy and fired up Process Explorer. Lock was held by sqlserver.exe - but there are two instances of sql server: sqlserver.exe PID: 4680 User Name: DefaultAppPool sqlserver.exe PID: 4644 User Name: NETWORK SERVICE The file is open by the sqlserver.exe instance with the PID: 4680 Stopping the "SQL Server (SQLEXPRESS)" service, killed off the process with PID: 4644, but left PID: 4680 alone. Seeing as the owner of the remaining process was DefaultAppPool, next thing I tried was stopping IIS (this database is being used from an ASP.Net application). Unfortunately this didn't kill the process off either. Manually killing off the remaining sql server process does remove the open file handle on the database files, allowing them to be copied/moved. Unfortunately I wish to copy/restore those files in some pre/post install tasks of a WiX installer - as such I was hoping there might be a way to achieve this by stopping a windows service, rather then having to shell out to kill all instances of sqlserver.exe as that poses some problems: Killing all the sqlserver.exe instances may have undesirable consequencies for users with other Sql Server instances on their machines. I can't restart those instances easily. Introduces additional complexities into the installer. Does anyone have any further thoughts on how to shutdown instances of sql server associated with a specific user instance?

    Read the article

  • 'Timeout Expired' error against local SQL Express on only 2 LINQ Methods...

    - by Refracted Paladin
    I am going to sum up my problem first and then offer massive details and what I have already tried. Summary: I have an internal winform app that uses Linq 2 Sql to connect to a local SQL Express database. Each user has there own DB and the DB stay in sync through Merge Replication with a Central DB. All DB's are SQL 2005(sp2or3). We have been using this app for over 5 months now but recently our users are getting a Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. Detailed: The strange part is they get that in two differnt locations(2 differnt LINQ Methods) and only the first time they fire in a given time period(~5mins). One LINQ method is pulling all records that match a FK ID and then Manipulating them to form a Heirarchy View for a TreeView. The second is pulling all records that match a FK ID and dumping them into a DataGridView. The only things I can find in common with the 2 are that the first IS an IEnumerable and the second converts itself from IQueryable - IEnumerable - DataTable... I looked at the query's in Profiler and they 'seemed' normal. They are not very complicated querys. They are only pulling back 10 - 90 records, from one table. Any thoughts, suggestions, hints whatever would be greatly appreciated. I am at my wit's end on this.... public IList<CaseNoteTreeItem> GetTreeViewDataAsList(int personID) { var myContext = MatrixDataContext.Create(); var caseNotesTree = from cn in myContext.tblCaseNotes where cn.PersonID == personID orderby cn.ContactDate descending, cn.InsertDate descending select new CaseNoteTreeItem { CaseNoteID = cn.CaseNoteID, NoteContactDate = Convert.ToDateTime(cn.ContactDate). ToShortDateString(), ParentNoteID = cn.ParentNote, InsertUser = cn.InsertUser, ContactDetailsPreview = cn.ContactDetails.Substring(0, 75) }; return caseNotesTree.ToList<CaseNoteTreeItem>(); } AND THIS ONE public static DataTable GetAllCNotes(int personID) { using (var context = MatrixDataContext.Create()) { var caseNotes = from cn in context.tblCaseNotes where cn.PersonID == personID orderby cn.ContactDate select new { cn.ContactDate, cn.ContactDetails, cn.TimeSpentUnits, cn.IsCaseLog, cn.IsPreEnrollment, cn.PresentAtContact, cn.InsertDate, cn.InsertUser, cn.CaseNoteID, cn.ParentNote }; return caseNotes.ToList().CopyLinqToDataTable(); } }

    Read the article

  • SQL Server 2008 R2

    - by kevchadders
    Hi all, I heard on the grapevine that Microsoft will be releasing SQL Server 2008 R2 within a year. Though I initially thought this was a patch for the just released 2008 version, I realised that it’s actually a completely different version that you would have to pay for. (Am I correct, if you had SQL Server 2008, would you have to pay again if you wanted to upgrade to 2008 R2?) If you’re already running SQL Server 2008, would you say it’s still worth the upgrade? Or does it depend on the size of your company and current setup. For what I’ve initially read, I do get the impression that this version would be more useful for the very high end hardware setup where you want to have very good scalability. With regard to programming, is there any extra enhancements/support in there which you’re aware of that will significantly help .NET Products/Web Development? Initially found a couple of links on it, but I was wondering if anyone had anymore info to share on subject as I couldn’t find nothing on SO about it? Thanks. New SQL Server R2 Microsoft Link on it. Microsoft SQL 2008 R2 EDIT: More information based on the Express Edition One very interesting thing about SQL Server 2008 R2 concerns the Express edition. Previous express versions of SQL Server Express had a database size limit of 4GB. With SQL Server Express 2008 R2, this has now been increased to 10GB !! This now makes the FREE express edition a much more viable option for small & medium sized applications that are relatively light on database requirements. Bear in mind, that this limit is per database, so if you coded your application cleverly enough to use a separate database for historical/archived data, you could squeeze even more out of it! For more information, see here: http://blogs.msdn.com/sqlexpress/archive/2010/04/21/database-size-limit-increased-to-10gb-in-sql-server-2008-r2-express.aspx

    Read the article

  • Compiler issues on VC++ 2008 Express, Seemingly correct code throws errors.

    - by Anthony Clever
    Hi there, I've been trying to get back into coding for a while, so I figured I'd start with some simple SDL, now, without the file i/o, this compiles fine, but when I throw in the stdio code, it starts throwing errors. This I'm not sure about, I don't see any problem with the code itself, however, like I said, I might as well be a newbie, and figured I'd come here to get someone with a little more experience with this type of thing to look at it. I guess my question boils down to: "Why doesn't this compile under Microsoft's Visual C++ 2008 Express?" I've attached the error log at the bottom of the code snippet. Thanks in advance for any help. #include "SDL/SDL.h" #include "stdio.h" int main(int argc, char *argv[]) { FILE *stderr; FILE *stdout; stderr = fopen("stderr", "wb"); stdout = fopen("stdout", "wb"); SDL_Init(SDL_INIT_EVERYTHING); fprintf(stdout, "SDL INITIALIZED SUCCESSFULLY\n"); SDL_Quit(); fprintf(stderr, "SDL QUIT.\n"); fclose(stderr); fclose(stdout); return 0; } /* 1>------ Build started: Project: opengl_crap, Configuration: Debug Win32 ------ 1>Compiling... 1>main.cpp 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(6) : error C2090: function returns array 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(6) : error C2528: '__iob_func' : pointer to reference is illegal 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(6) : error C2556: 'FILE ***__iob_func(void)' : overloaded function differs only by return type from 'FILE *__iob_func(void)' 1> c:\program files\microsoft visual studio 9.0\vc\include\stdio.h(132) : see declaration of '__iob_func' 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(7) : error C2090: function returns array 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(7) : error C2528: '__iob_func' : pointer to reference is illegal 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(9) : error C2440: '=' : cannot convert from 'FILE *' to 'FILE ***' 1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(10) : error C2440: '=' : cannot convert from 'FILE *' to 'FILE ***' 1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(13) : error C2664: 'fprintf' : cannot convert parameter 1 from 'FILE ***' to 'FILE *' 1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(15) : error C2664: 'fprintf' : cannot convert parameter 1 from 'FILE ***' to 'FILE *' 1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(17) : error C2664: 'fclose' : cannot convert parameter 1 from 'FILE ***' to 'FILE *' 1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast 1>c:\documents and settings\owner\my documents\visual studio 2008\projects\opengl_crap\opengl_crap\main.cpp(18) : error C2664: 'fclose' : cannot convert parameter 1 from 'FILE ***' to 'FILE *' 1> Types pointed to are unrelated; conversion requires reinterpret_cast, C-style cast or function-style cast 1>Build log was saved at "file://c:\Documents and Settings\Owner\My Documents\Visual Studio 2008\Projects\opengl_crap\opengl_crap\Debug\BuildLog.htm" 1>opengl_crap - 11 error(s), 0 warning(s) ========== Build: 0 succeeded, 1 failed, 0 up-to-date, 0 skipped ========== */

    Read the article

  • How can I make my PCI-E graphics card visible to Ubuntu when the motherboard has integrated graphics

    - by Norman Ramsey
    I have a Gigabyte GA-MA74GM-S2 motherboard with integrated graphics that shows up on lspci as an ATI Radeon 2100. I also bought a PCI-Express Nvidia graphics card so I could use the VDPAU feature on Linux (plays H.264 in hardware). The BIOS has three settings about which display to initialize first: Integrated graphics PCI graphics PCI-Express graphics (PEG) I set the BIOS on PEG, but I cannot get anything, not even a splash screen or POST messages, to emerge from the PCI-Express graphics card. (I'm using a DVI connector; the card also has an HDMI output.) I cannot get the kernel lspci to see the graphics card; the only VGA controller it acknowledges is the integrated one. Running dmidecode acknowledges the existence of an x16 PCI Express slot, and it says Current usage: Unknown There is an additional BIOS setting called "Internal Graphics Mode" which is normally set to "Auto" which means it is supposed to prefer a PCI Express VGA card. I set it to "Disabled" which now means I'm getting no output at all. I will soon be learning how to do a BIOS reset! Other information: The PCI-E card is a MSI N210-MD512H GeForce 210. This is a fanless card. Although there are no fans to see turning, the heat sink on the PCI-E card is definitely getting hot, so the card is getting some sort of power. It gets all its power from the PCI-E slot; there is no external power connector. The BIOS is an AMI Award BIOS. My question: how can I make the PCI Express graphics card visible to Ubuntu?

    Read the article

  • Exchange 2010 Internal Auto Discover Migrate away from current .local DNS name

    - by Bryan
    We have an Exchange 2010 Server, running within our Active Directory domain, with an internal hostname of server.example.local. The server is configured for Exchange anywhere, but currently has a self signed certificate with a name of server.example.local installed. Internally, clients connect and work fine, but externally, we are having certificate errors as you would expect. I'm about to purchase a UCC SSL Certificate to install on the server with all the relevant SANs on the certificate to correct this, but due to obvious problem obtaining a trusted cert with .local as a subject alternative name, I'm looking to configure clients on the internal network so that they don't use any reference to the .local hostname. I've configured our external DNS name for the server as exchange.example.com, and have created an CNAME for autodiscover.example.com which also (correctly) points to exchange.example.com. I've also configured internal DNS records for these two hostnames which point to the internal interface of the same server. I don't anticipate any problems here. I'm now trying to reconfigure Auto Discover internally, so that Outlook attempts to connect to exchange.example.com. I've followed the steps in KB940726 to prepare for this, and this appeared to work fine. No errors were generated and I was able to verify the CAS name in AD using ADSI edit. I've just tried testing this with a newly created test user account complete with a new Exchange mailbox, and Outlook 2007 connects fine on the internal network, but looking deeper in the Exchange profile, Outlook is still resolving the server name as server.example.local. Could it be the self signed cert, that is causing Outlook to display the server name as server.example.local, or is there still something wrong with my internal autodiscover configuration? Edit I've proven it isn't the certificate that is responsible for outlook returning server.example.local, by installing another self certified certificate with a name of test.example.com. When creating a new outlook profile, I get the mismatch error I'm expceting, but after accepting the cert, and finishing the config of the Outlook profile, again it still shows server.example.local as the server name. This means that if I were to purchase the UCC cert now, that external client would work fine, but internal clients would show a certificate name mismatch. Any ideas where to start diagnosing this?

    Read the article

  • Redirect or send mail in a script that runs in a rule on incoming mails in outlook 2010

    - by Guido Mertens
    I have the following problem: - I have a mails that are arriving in my mailbox - these mails contain a specific string in the body - what I want to do is: -- removing this string from the body -- then send this body to another mail adres (send, not forward) What have I already done: A. created a rule that activates the script in incoming messages that contain a certain string in the description This is the rule description: Apply to message with "Maileater" in the subject and on this computer only run "Project1.ChangeString" B. created the script with the following instructions: Public Sub ChangeString(MyMail As MailItem) Dim body As String body = MyMail.body body = Replace (body, "=====================================================", " ") MyMail.body = body MyMail.Save End Sub C. now I want to add in the script the instruction to send the body (or MyMail.body) to a specific mail adres (e.g. [email protected] with description "Support asked") after the replace of the string. is this possible? Can someone help me with this, I would be very greatfull because this will eliminate me from a lot of manual work. remark: this is just an exemple of a mail, the real thing will contain other replacements and mails to send

    Read the article

  • Will USMT 4.0 in MDT 2010 Move/Migrate the .NK2 File for Outlook?

    - by Mitch
    We're about to begin a refresh project for about 100 XP Pro laptops and have a concern with regards to the .NK2 file which holds cached email addresses(?). If possible we'd like to have USMT move/migrate this but I can't find anything that confirms that this happens automatically or has been done before. I see lots of manual processes but at this point I'm not sure that we can use that. Has anyone done this or seen this done? Perhaps you can point me to a resource that can give me an idea how its done? Any information would be appreciated. USMT seems to get a lot of the details but missing this part seems odd. Thanks in advance for any responses.

    Read the article

  • What's an alternative to using public folders (in Outlook)?

    - by Ivo Flipse
    My colleagues abuse our mail servers public folders to store (old) emails so that everyone can read them using IMAP. I'm looking into good alternatives after reading this Tech Republic article: "10 reasons why you should begin phasing out Exchange public folders" The most important thing they need is access to emails from multiple computers without overloading our network. So do you have any suggestions for alternatives? If there's a nice combination with some CRM system it would be interesting too. Note: this doesn't have to be freeware, usability and efficiency are more important. The solution has to be Windows 32 bit only

    Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >