Search Results

Search found 3249 results on 130 pages for 'packet loss'.

Page 85/130 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92 | Next Page >

Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

- by Jander

I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

Read the article
PowerConnect 3548p SNTP and web interface not working

- by Force Flow

I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

Read the article
mysqld refusing connections from localhost

- by Dennis Rardin

My mail server (Ubuntu 10.04) uses mysql for virtual domains, virtual users. For some reason, mysqld has started refusing connections from localhost. I see these in the mail server log: Oct 6 00:31:14 apollo postfix/trivial-rewrite[16888]: fatal: proxy:mysql:/etc/postfix/mysql-virtual_domains.cf(0,lock|fold_fix): table lookup problem and: Oct 7 13:39:15 apollo postfix/proxymap[25839]: warning: connect to mysql server 127.0.0.1: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I also get the following in auth.log: Oct 6 22:33:31 apollo mysqld[31775]: refused connect from 127.0.0.1 Telnet to the local port: root@apollo:/var/log/mysql# telnet localhost 3306 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. Connection closed by foreign host. root@apollo:/var/log/mysql# I am not sure why this started happening, but there was a disk failure in a RAID 1 pair a bit earlier that day. So it's possible I have a damaged config file or something. But mail was working for at least an hour after the drive event, so who knows for sure? phpmyadmin works fine, and the databases themselves look like they're intact. I think/believe that selinux and iptables are disabled and not running. So ... why is mysqld refusing connections from localhost? What should I check? What processes might cause this if a .conf file or possibly a binary was damaged? Which other log files might contain clues? I've enabled "general logging" in /etc/mysql/my.cnf, but I get no interesting or informative entries there. Thanks, m00tpoint

Read the article
Setting up a network where packets are traced

- by Marcus

My situation is the following: I have an internet connection, which is shared between people. More or less obviously, people is using it to download illegal stuff. Since I'm the owner of the connection, I want to avoid being sued. I don't want to prevent the people from doing the things they want, but I want to be legally safe. Now, I have relatively little competences in network administration, so I was wondering: is it possible to setup a network, where the source and destination of the packets are logged? I would use this to prove, in case of lawsuit, that the traffic was coming from a given machine. if the idea is feasible, is there any wireless router on which I can install linux, where I can install the packet sniffer? how much space could the logs take (containing only the timestamp/source/destination), per GB of traffic? a very rough estimation would be very helpful. if a machine on my network is sending bittorrent packets to a certain IP, would this log be able to reflect the time, source ip and destination ip? I assume that obviously the torrent data would be encrypted and un-decryptable. Am I missing something? Is there a better strategy? Any pointer to documentation would be helpful as well - in that case, I would use this as starting point.

Read the article
Best Work Queue service for distributed clusters

- by onewheelgood

Hi there. I require a simple work queue type system for asynchronous task management. I have looked at both beanstalkd and gearman. However, both these seem to assume that the client and the queue server are on the same network, and therefore that there will always be a reliable network between them. I need one that can support the client and server being in different places in the world, and be able to manage temporary loss of network connection between clusters. Ideally, this would work in such a way where I post a job to a local proxy that attempts to send it to the main queue server. If there is no network connection, it would try again later, however it would not lose the job or delay the client. Any recommendations?

Read the article
iptables to block non-VPN-traffic if not through tun0

- by dacrow

I have a dedicated Webserver running Debian 6 and some Apache, Tomcat, Asterisk and Mail-stuff. Now we needed to add VPN support for a special program. We installed OpenVPN and registered with a VPN provider. The connection works well and we have a virtual tun0 interface for tunneling. To archive the goal for only tunneling a single program through VPN, we start the program with sudo -u username -g groupname command and added a iptables rule to mark all traffic coming from groupname iptables -t mangle -A OUTPUT -m owner --gid-owner groupname -j MARK --set-mark 42 Afterwards we tell iptables to to some SNAT and tell ip route to use special routing table for marked traffic packets. Problem: if the VPN failes, there is a chance that the special to-be-tunneled program communicates over the normal eth0 interface. Desired solution: All marked traffic should not be allowed to go directly through eth0, it has to go through tun0 first. I tried the following commands which didn't work: iptables -A OUTPUT -m owner --gid-owner groupname ! -o tun0 -j REJECT iptables -A OUTPUT -m owner --gid-owner groupname -o eth0 -j REJECT It might be the problem, that the above iptable-rules didn't work due to the fact, that the packets are first marked, then put into tun0 and then transmitted by eth0 while they are still marked.. I don't know how to de-mark them after in tun0 or to tell iptables, that all marked packet may pass eth0, if they where in tun0 before or if they going to the gateway of my VPN provider. Does someone has any idea to a solution? Some config infos: iptables -nL -v --line-numbers -t mangle Chain OUTPUT (policy ACCEPT 11M packets, 9798M bytes) num pkts bytes target prot opt in out source destination 1 591K 50M MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 MARK set 0x2a 2 82812 6938K CONNMARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner GID match 1005 CONNMARK save iptables -nL -v --line-numbers -t nat Chain POSTROUTING (policy ACCEPT 393 packets, 23908 bytes) num pkts bytes target prot opt in out source destination 1 15 1052 SNAT all -- * tun0 0.0.0.0/0 0.0.0.0/0 mark match 0x2a to:VPN_IP ip rule add from all fwmark 42 lookup 42 ip route show table 42 default via VPN_IP dev tun0

Read the article
Routing table on Linux not respected

- by MRHaarmann

I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

Read the article
C# Abort()ing threads on exit for a Form

- by Gio Borje

So far I have this code run when the X button is clicked, but I'm not sure if this is the correct way to terminate threads on a form on exit. Type t = this.GetType(); foreach (PropertyInfo pi in t.GetProperties()) { if (pi.GetType() == typeof(Thread)) { MethodInfo mi = pi.GetType().GetMethod("Abort"); mi.Invoke(null, new object[] {}); } } I keep getting this error: "An attempt has been made to free an RCW that is in use. The RCW is in use on the active thread or another thread. Attempting to free an in-use RCW can cause corruption or data loss."

Read the article
Auto SSH and execute script

- by rohanbk

I have roughly 12 computers that each have the same script on them. This script merely pings all the other machines, and prints out whether the machine is "reachable" or "unreachable". However, it is inefficient to login to each machine manually using ssh to execute this script. Suppose I'm logged into node 1. Is there any way to for me to login to node 2-12 automatically using SSH, execute the ping script, pipe the results to a file, logout and proceed to the next machine? Some kind of bash shell script? I'm afraid I'm at a loss here since I haven't had experience with shell-scripting before.

Read the article
I'm installing mysql with homebrew, how do I set value to 'log_output'?

- by imjared

I've been following directions here: brew install mysql on mac os and have now run into the same issue both on my home machine and work (both MacBook Pro running OSX 10.7.5 and ZSH): 121031 12:18:03 [ERROR] /usr/local/opt/mysql/bin/mysqld: Error while setting value '/Users/me/.mysql/logs/' to 'log_output' The full output of the error can be found in this gist: https://gist.github.com/3988275 I'm really at a loss for what I'm doing incorrectly or what I need to change. It should be noted that there are no logs for me to check in /usr/local/var/mysql. Any help is greatly appreciated.

Read the article
How do I keep a bridge enabled on a bonded interface?

- by jlawer

I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

Read the article
Display On-Screen Television Graphics During Live Broadcasts

- by ServAce85

How and with what software do major television companies display on-screen graphics during their programs? For example: On ESPN, how do they produce the news ticker on the bottom (both graphically and from a source code point of view), create and display the scores of sports, and update and show selected stats on the fly? I've looked everywhere I can think of to find the answer, but I am at a loss. That's where you guys (and girls) come in. I hope you can help shed some light on this subject for me. Thanks in advance.

Read the article
C++ : Lack of Standardization at the Binary Level

- by Nawaz

Why ISO/ANSI didn't standardize C++ at the binary level? There are many portability issues with C++, which is only because of lack of it's standardization at the binary level. Don Box writes, (quoting from his book Essential COM, chapter COM As A Better C++) C++ and Portability Once the decision is made to distribute a C++ class as a DLL, one is faced with one of the fundamental weaknesses of C++, that is, lack of standardization at the binary level. Although the ISO/ANSI C++ Draft Working Paper attempts to codify which programs will compile and what the semantic effects of running them will be, it makes no attempt to standardize the binary runtime model of C++. The first time this problem will become evident is when a client tries to link against the FastString DLL's import library from a C++ developement environment other than the one used to build the FastString DLL. Are there more benefits Or loss of this lack of binary standardization?

Read the article
JavaScript To Strip Page For URL

- by Russell C.

We have a javascript function we use to track page stats internally. However, the URLs it reports many times include the page numbers for search results pages which we would rather not be reported. The pages that are reports are of the form: http://www.test.com/directory1/2 http://www.test.com/directory1/subdirectory1/15 http://www.test.com/directory3/1113 Instead we'd like the above reported as: http://www.test.com/directory1 http://www.test.com/directory1/subdirectory1 http://www.test.com/directory3 Please note that the numbered 'directory' and 'subdirectory' names above are just for example purposes and that the actual subdirectory names are all different, don't necessarily include numbers at the end of the directory name, and can be many levels deep. Currently our JavaScript function produces these URLs using the code: var page = location.hostname+document.location.pathname; I believe we need to use the JavaScript replace function in combination with some regex but I'm at a complete loss as to what that would look like. Any help would be much appreciated! Thanks in advance!

Read the article
VPN sharing on Mac OS X 10.5 machine

- by Jens

I have a rather weird problem. I want to share a VPN connection that has been established by my Mac OS X 10.5 computer with another machine in my network. This is what I did: In the /etc/hostcongig file on the main computer I added the line: IPFORWARDING=-YES- I assigned a fixed IP address to my computer (192.168.178.30), a fixed one to the other machine (192.168.178.60) and my computer's IP address as gateway on the other machine. I connected to my VPN using the internal Mac OS X VPN client (PPTP connection) I run this script: #!/bin/sh natd -same_ports -use_sockets -unregistered_only -dynamic -interface ppp0 -clamp_mss ipfw -f flush ipfw add divert natd ip from any to any via ppp0 ipfw add pass all from any to any sysctl -w net.inet.ip.forwarding=1 Source: Using (and sharing) a VPN connection on your Mac Now everthing works smootly, however speed is an issue. I get 1,8 MBit/s on my main machine and only 0,3 - 0,6 MBit/s on the other one. My question: What could possibly be wrong? Do I have to tweak MTU settings, is there any packet inspection ongoing that needs time....? Any help appreciated!

Read the article
More XML Problems - Undeclared Entity 'nbsp'

- by Gogster

I'm getting the error: Line 49: xml = r.ReadToEnd(); Line 50: Line 51: System.Xml.Linq.XDocument xmlDoc = System.Xml.Linq.XDocument.Parse(xml); Line 52: Line 53: var query = from p in xmlDoc.Descendants("member") On my XML. When I run the code to generate the XML in an empty page, it runs without error, if I call the code within my webpage it throws this error. The only 'nbsp' on the page is a doctype declaration at the top of the XSLT: <!DOCTYPE xsl:stylesheet [ <!ENTITY nbsp " "> ]> I'm at a loss as to where this error is coming from and I am looking for suggestions please! Thanks.

Read the article
SQL SELECT across two tables

- by Brett Spurrier

Hi there, I am a little confused as to how to approach this SQL query. I have two takes (equal number of records), and I would like to return a column with which is the division between the two. In other words, here is my not-working-correctly query: SELECT( (SELECT v FROM Table1) / (SELECT DotProduct FROM Table2) ); How would I do this? All I want it a column where each row equals the same row in Table1 divided by the same row in Table2. The resulting table should have the same number of rows, but I am getting something with a lot more rows than the original two tables. I am at a complete loss. Any advice?

Read the article
Using Fortran to call C++ Functions

- by Dane Larsen

I'm trying to get some FORTRAN code to call a couple c++ functions that I wrote (c_tabs_ being one of them). Linking and everything works just fine, as long as I'm calling functions that don't belong to a class. My problem is that the functions I want the FORTRAN code to call belong to a class. I looked at the symbol table using nm and the function name is something ugly like this: 00000000 T _ZN9Interface7c_tabs_Ev FORTRAN won't allow me to call a function by that name, because of the underscore at the beginning, so I'm at a loss. The symbol for c_tabs when it's not in a class is quite simple, and FORTRAN has no problems with it: 00000030 T c_tabs_ Any suggestions? Thanks in advance.

Read the article
Linux server: Dropped packets

- by Lars

I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

Read the article
FORTRAN function returning an array causes a segfault (calling from C++)

- by Dane Larsen

Basically, here's my problem. I'm calling someone else's FORTRAN functions from my C++ code, and it's giving me headaches. Some code: function c_error_message() character(len = 255) :: c_error_message errmsg(1:9) = 'ERROR MSG' return end That's the FORTRAN function. My first question is: Is there anything in there that would cause a segfault? If not, then second: What does that return? A pointer? I'm trying to call it with the following C statement: char *e = c_error_message_(); That causes a segfault. c_error_message(); That too causes a segfault. I declared c_error_message_() earlier on with the following code: extern"C" { char* c_error_message_(); } Would declaring a function with a different return type than the actual return type cause a segfault? I'm at a loss. Thanks for any replies.

Read the article
ASP.NET forgets dlls in bin directory

- by Timothy Strimple

We have a plugin system on a WCF service that checks libraries placed in the bin folder for certain assembly level attributes and loads them. This allows customization of certain service calls based on which client is making the call. This works great most of the time. However, sometimes it seems to lose the dll, which causes the service to revert back to the default implementation for every client. The solution so far has been to just move the dll file out of the bin folder, and back in. This causes asp.net to pick up the file and customizations start working again. I'm at a loss for why the assembly is getting missed like that after a certain amount of time. Any ideas as to what might be causing this?

Read the article
virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

- by Chris Gow

Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

Read the article
Looking for a small, portable, port-mirroring ethernet switch.

- by user37244

I recently had a mac go haywire, taking half a minute or more to get www.google.com loaded. Getting its owner to give up the machine for repair was like pulling teeth - they were insisting that it must be something to do with the network, since so much had changed with the local configuration at about the same time their box went haywire. I eventually set up a port mirror to a box that I could remote to so I could show that the mac was only irregularly getting packets onto the network. Demonstrating this faced an additional challenge: the latency of the remote desktop software I was using meant that I had to point to timestamps instead of just the moment the packet flashed up on the screen as my evidence. This particular user was the reason this was so challenging this time around, but I would like to have a box that I can cart from desk to desk to use wireshark on my laptop at any station where I need it. 3com, cisco, netgear, etc. (ad nauseum), all make switches that can be configured for port mirroring, but in my case, the smaller, the better. For the sake of my sanity, I'll probably end up running it off a battery anyway. If my laptop had two ethernet ports, this would be easy. So, whaddya recommand for a device that requires 0 configuration at each powerup (though I'm fine with poking at it for a while to set it up initially.) Small, light, and cheap enough to get it past purchasing? Thanks,

Read the article
Crystal Reports and WMF image

- by Eve

I have a problem with inserting a vector graphics (WMF) into report (Crystal Reports v10.5 from Visual Studio 2008). The image is static, inserted by choosing "Insert Picture" during report design in VS. The problem is that it displays differently (size and aspect ratio) on machines with different operating systems and screen resolutions. Converting to bitmap isn't possible beacause loss of the quality of print isn't acceptable. I thought about dynamic loading of the image, but in this version of CR. I don't see a possibility to set dynamic graphic location in picture properties. Is there any way to solve this problem?

Read the article
Packets being dropped by iptables

- by Shadyabhi

I am trying to create a Software Access Point in linux. I followed the blog here. Steps I performed: Started dhcp server on wlan0. Properly configured hostapd.conf Enabled packet forwarding & masquerading. Two commands executed regarding iptables: iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface wlan0 -j ACCEPT I enabled logging on iptables & I get this in everything.log Jun 29 19:42:03 MBP-archlinux kernel: [10480.180356] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=38025 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.389102] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=308 TOS=0x00 PREC=0x00 TTL=52 ID=14732 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK PSH URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.389710] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=14988 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK FIN URGP=0 Jun 29 19:42:03 MBP-archlinux kernel: [10480.621118] IN=eth0 OUT=wlan0 MAC=c8:bc:c8:9b:c4:3c:00:13:80:40:cd:80:08:00 SRC=195.143.92.150 DST=10.0.0.3 LEN=44 TOS=0x00 PREC=0x00 TTL=52 ID=63378 PROTO=TCP SPT=80 DPT=53570 WINDOW=46185 RES=0x00 ACK FIN URGP=0 I have almost no knowledge of iptables, all I did was through googling. So, can anyone help me in making me understand what wrong is happening here? I have tried running tcpdump on wlan0 & http packets are being sent from wlan0.

Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92 | Next Page >