Search Results

Search found 2911 results on 117 pages for 'payment gateway'.

Page 85/117 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

  • Ubuntu 12.04 connected to wireless network but internet not working

    - by A.J.
    I can connect to my house's wireless network just fine, but when I'm connected I can't browse the web. Firefox starts connecting to a site and then just poops out. This doesn't happen on my roommates' computers (running Windows) or on our 3DSes, so I know it's just my laptop. I already tried sudo dhclient -r sudo dhclient sudo ifconfig eth0 down sudo ifconfig eth0 up Results of a few commands I was asked to run in comments: ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. ^C --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (173.194.33.38) 56(84) bytes of data. --- google.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 88:AE:1D:6B:4E:E7 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off - Device: wlan0 [JUSTICE] ----------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: connected Default: yes HW Address: 1C:65:9D:65:C6:31 Capabilities: Speed: 1 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) HOME-9B18: Infra, 00:26:F3:53:9B:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 34 WPA WPA2 cougdad48 Network: Infra, 60:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 22 WPA2 cougdad48 Guest Network: Infra, 66:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA2 belkin.ade: Infra, 94:44:52:FF:8A:DE, Freq 2457 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 *JUSTICE: Infra, 00:24:01:7B:9F:7E, Freq 2462 MHz, Rate 54 Mb/s, Strength 88 WEP CenturyLink: Infra, B2:B2:DC:8E:E2:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 IPv4 Settings: Address: 192.168.0.11 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 (JUSTICE is my home's network.) ping -c 2 198.168.0.1 PING 198.168.0.1 (198.168.0.1) 56(84) bytes of data. --- 198.168.0.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms

    Read the article

  • Youtube video streaming slow

    - by Newbie
    When I try to stream youtube videos on my ubuntu 11.04, they don't stream smoothly. They buffer well and are choppy. Here's my Config: Laptop: Gateway NV58 Ram : 4 GB Ethernet Controller: Broadcom Corp NetLink BCM5784M Gigabit Ethernet PCIe (rev10) Let me know if you need more details. Output of lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10) 04:00.0 Network controller: Intel Corporation WiFi Link 5100

    Read the article

  • How to connect Ethernet on Ubuntu (with auto-detection)

    - by user12285
    It's been well over six months but I have the same router SmartAX MT880d with Ethernet, and the exact same problem : no internet, even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. I'm a total beginner with Ubuntu. My internet works great in Windows but does not work in Ubuntu. Sorry if I don't use the right (technical) terminology to explain my issue. English is not my mother tongue. For 2 weeks, I've been doing reading on the web and forums and the ubuntuguide.org to name a few, but to no avail. Now I see no other solution but to ask for help. My problem is that I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files. E.g.: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm concerned that I might put figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem? Is the subnet 255.255.255.0? Gateway 192.168.1.1? I'm confused as I can also see a different IP starting with 155131*** (is it an account number?) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • Static IP configuration causing apt-get errors

    - by JPbuntu
    I am getting errors when running apt-get update or when installing new packages. Although this only happens when the server configured for a static IP address. Changing the configuration back to DHCP and restarting networking fixes the problem, although I want a static IP. Once it is working I can change back to my static IP address and restart networking. Although this only works until I restart the server (restarting the router is ok), and then I start getting the same errors and have to switch back to DHCP. Any ideas on what could be causing this or tips on troubleshooting it? Thanks in advance. here is my static IP configuration: auto eth0 iface eth0 inet static address 192.168.2.2 netmask 255.255.255.0 gateway 192.168.2.1 The apt-get update errors go something like this: A few of these Ign http://us.archive.ubuntu.com precise-backports InRelease then a lot of these Err http://security.ubuntu.com precise-security Release.gpg Something wicked happened resolving 'security.ubuntu.com:http' (-5 - No address associated with hostname) and a lot of these W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-backports/universe/i18n/Translation-en Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname)

    Read the article

  • lxc containers fail to autoboot in 14.04 trusty using 'lxc.start.auto = 1'

    - by user273046
    In trusty 14.04 containers fail to autoboot despite all settings being set as 14.04 requires. They show all as STOPPED I have correctly configured 2 LXC containers: calypso encelado They run perfectly if I run sudo lxc-autostart then sudo lxc-ls --fancy results in: ubuntu@saturn:/etc/init$ sudo lxc-ls --fancy NAME STATE IPV4 IPV6 AUTOSTART calypso RUNNING 192.168.1.161 - YES encelado RUNNING 192.168.1.162 - YES The problem is trying to run them at boot. I have at: /var/lib/lxc/calypso/config: # Template used to create this container: /usr/share/lxc/templates/lxc-download # Parameters passed to the template: # For additional config options, please look at lxc.conf(5) # Distribution configuration lxc.include = /usr/share/lxc/config/ubuntu.common.conf lxc.arch = x86_64 # Container specific configuration lxc.rootfs = /var/lib/lxc/calypso/rootfs lxc.utsname = calypso # Network configuration lxc.network.type = veth lxc.network.flags = up #lxc.network.link = lxcbr0 lxc.network.link = br0 lxc.network.hwaddr = 00:16:3e:64:0b:6e # Assegnazione IP Address lxc.network.ipv4 = 192.168.1.161/24 lxc.network.ipv4.gateway = 192.168.1.1 # Autostart lxc.start.auto = 1 lxc.start.delay = 5 lxc.start.order = 100 and I have LXC_AUTO="false" as required inside /etc/default/lxc: LXC_AUTO="false" USE_LXC_BRIDGE="false" # overridden in lxc-net [ -f /etc/default/lxc-net ] && . /etc/default/lxc-net LXC_SHUTDOWN_TIMEOUT=120 Any idea on why the containers don't start at boot? At reboot they are always in the STOPPED state: ubuntu@saturn:~$ sudo lxc-ls --fancy NAME STATE IPV4 IPV6 AUTOSTART calypso STOPPED - - YES encelado STOPPED - - YES and then again they can be started manually, using sudo lxc-autostart

    Read the article

  • CodePlex Daily Summary for Wednesday, June 12, 2013

    CodePlex Daily Summary for Wednesday, June 12, 2013Popular ReleasesWeb Pages CMS: 0.5.0.5: Added empty media directoryWindows 8 App Desing Reference Template: Education Big Picture: EducationBigPicture: Download includes the following -> Source (C# and JS) -> Package -> Snapshots -> DocumentationModern UI for WPF: Modern UI 1.0.4: The ModernUI assembly including a demo app demonstrating the various features of Modern UI for WPF. Related downloads NuGet ModernUI for WPF is also available as NuGet package in the NuGet gallery, id: ModernUI.WPF Download Modern UI for WPF Templates A Visual Studio 2012 extension containing a collection of project and item templates for Modern UI for WPF. The extension includes the ModernUI.WPF NuGet package. DownloadToolbox for Dynamics CRM 2011: XrmToolBox (v1.2013.6.11): XrmToolbox improvement Add exception handling when loading plugins Updated information panel for displaying two lines of text Tools improvementMetadata Document Generator (v1.2013.6.10)New tool Web Resources Manager (v1.2013.6.11)Retrieve list of unused web resources Retrieve web resources from a solution All tools listAccess Checker (v1.2013.2.5) Attribute Bulk Updater (v1.2013.1.17) FetchXml Tester (v1.2013.3.4) Iconator (v1.2013.1.17) Metadata Document Generator (v1.2013.6.10) Privilege...Document.Editor: 2013.23: What's new for Document.Editor 2013.23: New Insert Emoticon support Improved Format support Minor Bug Fix's, improvements and speed upsChristoc's DotNetNuke Module Development Template: DotNetNuke 7 Project Templates V2.4 for VS2012: V2.4 - Release Date 6/10/2013 Items addressed in this 2.4 release Updated MSBuild Community Tasks reference to 1.4.0.61 Setting up your DotNetNuke Module Development Environment Installing Christoc's DotNetNuke Module Development Templates Customizing the latest DotNetNuke Module Development Project TemplatesLayered Architecture Sample for .NET: Leave Sample - June 2013 (for .NET 4.5): Thank You for downloading Layered Architecture Sample. Please read the accompanying README.txt file for setup and installation instructions. This is the first set of a series of revised samples that will be released to illustrate the layered architecture design pattern. This version is only supported on Visual Studio 2012. This samples illustrates the use of ASP.NET Web Forms, ASP.NET Model Binding, Windows Communications Foundation (WCF), Windows Workflow Foundation (WF) and Microsoft Ente...Papercut: Papercut 2013-6-10: Feature: Shows From, To, Date and Subject of Email. Feature: Async UI and loading spinner. Enhancement: Improved speed when loading large attachments. Enhancement: Decoupled SMTP server into secondary assembly. Enhancement: Upgraded to .NET v4. Fix: Messages lost when received very fast. Fix: Email encoding issues on display/Automatically detect message Encoding Installation Note:Installation is copy and paste. Incoming messages are written to the start-up directory of Papercut. If you do n...SFDL.NET: SFDL.NET v1.1.0.4: Changelog: Ciritical Bug Fixed : Downloading of Files not possibleMapWinGIS ActiveX Map and GIS Component: MapWinGIS v4.8.8 Release Candidate - 32 Bit: This is the first release candidate of MapWinGIS. Please test it thoroughly.MapWindow 4: MapWindow GIS v4.8.8 - Release Candidate - 32Bit: Download the release notes here: http://svn.mapwindow.org/svnroot/MapWindow4Dev/Bin/MapWindowNotes.rtfLINQ to Twitter: LINQ to Twitter v2.1.06: Supports .NET 3.5, .NET 4.0, .NET 4.5, Silverlight 4.0, Windows Phone 7.1, Windows Phone 8, Client Profile, Windows 8, and Windows Azure. 100% Twitter API coverage. Also supports Twitter API v1.1! Also on NuGet.VR Player: VR Player 0.3 ALPHA: New plugin system with individual folders TrackIR support Maya and 3ds max formats support Dual screen support Mono layouts (left and right) Cylinder height parameter Barel effect factor parameter Razer hydra filter parameter VRPN bug fixes UI improvements Performances improvements Stabilization and logging with Log4Net New default values base on users feedback CTRL key to open menuSimCityPak: SimCityPak 0.1.0.8: SimCityPak 0.1.0.8 New features: Import BMP color palettes for vehicles Import RASTER file (uncompressed 8.8.8.8 DDS files) View different channels of RASTER files or preview of all layers combined Find text in javascripts TGA viewer Ground textures added to lot editor Many additional identified instances and propertiesWsus Package Publisher: Release v1.2.1306.09: Add more verifications on certificate validation. WPP will not let user to try publishing an update until the certificate is valid. Add certificate expiration date on the 'About' form. Filter Approbation to avoid a user to try to approve an update for uninstallation when the update do not support uninstallation. Add the server and console version on the 'About' form. WPP will not let user to publish an update until the server and console are not at the same level. WPP do not let user ...AJAX Control Toolkit: June 2013 Release: AJAX Control Toolkit Release Notes - June 2013 Release Version 7.0607June 2013 release of the AJAX Control Toolkit. AJAX Control Toolkit .NET 4.5 – AJAX Control Toolkit for .NET 4.5 and sample site (Recommended). AJAX Control Toolkit .NET 4 – AJAX Control Toolkit for .NET 4 and sample site (Recommended). AJAX Control Toolkit .NET 3.5 – AJAX Control Toolkit for .NET 3.5 and sample site (Recommended). Notes: - Instructions for using the AJAX Control Toolkit with ASP.NET 4.5 can be found at...Rawr: Rawr 5.2.1: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...VG-Ripper & PG-Ripper: PG-Ripper 1.4.13: changes NEW: Added Support for "ImageJumbo.com" links FIXED: Ripping of Threads with multiple pagesJson.NET: Json.NET 5.0 Release 6: New feature - Added serialized/deserialized JSON to verbose tracing New feature - Added support for using type name handling with ISerializable content Fix - Fixed not using default serializer settings with primitive values and JToken.ToObject Fix - Fixed error writing BigIntegers with JsonWriter.WriteToken Fix - Fixed serializing and deserializing flag enums with EnumMember attribute Fix - Fixed error deserializing interfaces with a valid type converter Fix - Fixed error deser...Biller: Biller 1.49: This release fixes company sales statisticsNew Projectsapiviewer: Documentation viewer for your service API.ArgusLib: Set of libraries I use in most of my projects.arwani: this is armani project.Blue Mercs Data Gateway: The Data Gateway is an open source project which simplifies coding fluently database SQL statements, stored procedure, connections and transactions.Convert Hashtable Rows into DataTable Columns in C#: Simplest way to convert a Hashtable into a DataTable with all the Hashtable rows converted into DataTable columns.everynet: EveryNet is an internet service provider servicing homes Fraktalysator: Software to visualize fractals such as the Mandelbrot Set. Still in early development state.Free BarCode API for .NET: Freee BarCode API for .NETGraphic filters in WPF: FiltersGrid Plugin: Grid Plugin , Turn your <table> into a fully functional price grid.mediamonitor: this is mediamonitor project.MyCodingStuffs: This solution includes C#, WCF, MVC4.0, ASP.net libraries.OpenErp .Net Connector: Access to OpenErp from .NetPhong and Flat shading: Phong shadingPixel Replacer: The Pixel Replacer is a simple library for replacing pixel colors with a new color, by setting a filter rule.plainetl in vb.net: a one db to another db transform, threaded, commandline tool, ... initially created to get a flat-File db (FoxPro) into a mssql.Programming in HTML5 with JavaScript and CSS3: Contains material developed while visiting a Microsoft course for the MCSD exam 70-480ProjectLinker2012: This tool helps to automatically create and maintain links from a source project to a target project to share code that is common to Silverlight and WPF.SALDERA Project: SALDERA TEST Project Summary Mire lesz ez jó? Majd Kiderül.TCPMessageServer: Simple TCP Client/Server used to pass an object between client and serverThats-Me Dot Net API: Thats-Me Dot Net API is a library which implements the Thats-Me.ch API for the Dot Net Framework.T-Sql Code Documentor: Document T-SQL Code and Extract Comments for all objects in a database.Windows 8 App Design Reference Template: Measurement: Measurement template will help if you want to build an app which addresses Mass/Weight, Distance/Length, Capacity/Volume etc. measurement placeholders.Windows 8 App Design Reference Template: Weather Clock: Weather Clock Template will help if you want to build an app which has the features to add Current/Previous day temperatures and add cities for coverage. Windows 8 App Desing Reference Template: Education Big Picture: Education Big Picture Template will help if you want to build an app which has an option for showcasing campus details, courses, student life etc dataWinodws 8 App Design Reference Template: Social Feed: Social Feed template will help if you want to build an app which has the Messaging, Facebook, twitter feeds sections. WP7FlacPlayer: Implemented JFlacLib in C# A simple player to play flac in windows phone system

    Read the article

  • apt-get issue after upgrading to 12.04

    - by user83906
    I have recently upgraded my cluster from 11.10 to 12.04. After the upgrade, I am having trouble running apt-get on the cluster nodes. I can ssh between the nodes (client-to-client; client-to-head; client-to-external etc.). However, sudo apt-get update produces the following errors: Ign http://us.archive.ubuntu.com precise InRelease Ign http://security.ubuntu.com precise-security InRelease Ign http://www.openfoam.org maverick InRelease Ign http://us.archive.ubuntu.com precise-updates InRelease Err http://security.ubuntu.com precise-security Release.gpg Something wicked happened resolving 'security.ubuntu.com:http' (-5 - No address associated with hostname) Err http://www.openfoam.org maverick Release.gpg Something wicked happened resolving 'www.openfoam.org:http' (-5 - No address associated with hostname) Ign http://us.archive.ubuntu.com precise-backports InRelease Ign http://www.openfoam.org maverick Release Ign http://security.ubuntu.com precise-security Release Err http://us.archive.ubuntu.com precise Release.gpg Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname) Ign http://security.ubuntu.com precise-security/main Sources/DiffIndex Err http://us.archive.ubuntu.com precise-updates Release.gpg Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname) Ign http://security.ubuntu.com precise-security/restricted Sources/DiffIndex 15% [Connecting to us.archive.ubuntu.com] [Connecting to security.ubuntu.com] [Connecting to www.openfoam.org] On the headnode, I have in /etc/network/iterfaces: auto eth0 iface eth0 inet static address 192.168.0.1/24 On the client nodes, I have /etc/network/iterfaces: auto eth0 iface eth0 inet static address 192.168.0.101 netmask 255.255.255.0 gateway 192.168.0.1 Please advise.

    Read the article

  • How to connect to a wireless network that has a two word name with a space?

    - by grinan
    Ok, I have searched for some time in earnest for an answer to this question. I have a Beagleboard which has Ubuntu 10.10 Minimal install for Arm running on it. With the default install, minimal tools, no GUI, I am unable to connect to my wireless network. The name of my network is "MYNAME NETWORK". Using a text editor to edit /etc/network/interfaces I can not seem to connect at all. As an experiment, I connected to a friends network, which has a one word name "dystek",and was able to connect with Zero issues, and update and install a full GUI for ubuntu Arm. The problem is that I don't want a full blown gui on the beagleboard, just a minimal install of ubuntu with CLI is all I need or want. Is there anyway to connect to my wireless network via editing the /etc/network/interfaces file. Surely there is... I just don't know how. Right now my interfaces file looks like this: auto lo iface lo inet loopback auto wlan0 iface wlan0 inet static address 192.168.1.200 netmask 255.255.255.0 gateway 192.168.1.1 wireless-essid BARRETT NETWORK wireless-key 46456xxxxxxxx Any help would be appreciated.

    Read the article

  • Not able to connect to local network

    - by Roopesh
    I have installed Kubuntu , I am able to connect to Internet and able to access external sites, but in my local network i have bugzila installed that i am not able to access, even i am not able to ping the gateway also 192.168.1.1 . below is the result of ifconfig command Please help . Thanks ~# ifconfig eth0 Link encap:Ethernet HWaddr b8:70:f4:da:f9:a8 inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:884 errors:0 dropped:0 overruns:0 frame:0 TX packets:884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:81131 (81.1 KB) TX bytes:81131 (81.1 KB) wlan0 Link encap:Ethernet HWaddr 68:5d:43:2e:1c:79 inet addr:192.168.1.26 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe2e:1c79/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2446 errors:0 dropped:0 overruns:0 frame:0 TX packets:2324 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1909441 (1.9 MB) TX bytes:393292 (393.2 KB)

    Read the article

  • Routing tables don't show ppp0 after 12.04 kernel upgrade to 3.5.0: Haier CE682 modem configuration

    - by ubunsteve
    I'm trying to get my Haier CE682 EVDO modem, model number 201e:1022 to work in ubuntu 12.04 kernel 3.5.0-030500-generic #201207211835 . I had it working in a previous 12.04 kernel, using compat-wireless and these instructions http://zulkhamsyahmh.blogspot.com/2012/05/install-smartfren-haier-ce682-on-ubuntu.html, and to get it working had to edit the routing tables so that there was a ppp0 showing up, as suggested at http://www.linuxquestions.org/questions/slackware-14/wvdial-is-connecting-but-im-unable-to-do-anything-714861/ Network manager doesn't work with this modem, so I use either wvdial or gpppon to connect to it, both which work (after I run the command sudo modprobe usbserial vendor=0x201e product=0x1022 ) This is the output of when I connect with gpppon to the modem: Using interface ppp0 Connect: ppp0 <-- /dev/ttyUSB0 sent [LCP ConfReq id=0x1 ] rcvd [LCP ConfAck id=0x1 ] rcvd [LCP ConfReq id=0x2 ] sent [LCP ConfAck id=0x2 ] sent [LCP EchoReq id=0x0 magic=0x819c86db] rcvd [CHAP Challenge id=0x1 <1ac8f12799e953967a3cc222c9254690, name = ""] sent [CHAP Response id=0x1 <6f12a903dc40915ca2761c17b87f8fbd, name = "smart"] rcvd [LCP EchoRep id=0x0 magic=0x0] rcvd [CHAP Success id=0x1 ""] CHAP authentication succeeded CHAP authentication succeeded sent [CCP ConfReq id=0x1 ] sent [IPCP ConfReq id=0x1 ] rcvd [IPCP ConfReq id=0x1 ] sent [IPCP ConfAck id=0x1 ] rcvd [CCP ConfReq id=0x1] sent [CCP ConfAck id=0x1] rcvd [CCP ConfRej id=0x1 ] sent [CCP ConfReq id=0x2] rcvd [IPCP ConfRej id=0x1 ] sent [IPCP ConfReq id=0x2 ] rcvd [CCP ConfAck id=0x2] rcvd [IPCP ConfNak id=0x2 ] sent [IPCP ConfReq id=0x3 ] rcvd [IPCP ConfAck id=0x3 ] not replacing existing default route via 192.168.3.1 local IP address 10.191.248.154 remote IP address 10.17.95.25 primary DNS address 10.17.3.244 secondary DNS address 10.17.3.245 as you can see there is a problem with "not replacing existing default route via 192.168.3.1" This it the out put of route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.3.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.3.0 * 255.255.255.0 U 2 0 0 wlan0 I had tried these commands, which had previously worked in the earlier kernel: route del default route add default ppp0 but that broke my wireless internet connection. I then added the default routing as shown above with sudo route add default gw 192.168.3.1 wlan0 So it seems I need to add or change the routing to show a ppp0 connection, but I don't know how to do that.

    Read the article

  • Bluetooth not working on Acer 3820tg (Ubuntu 12.04)

    - by Iohannes
    After upgrading to 12.04 (it was done by a complete reinstallation), bluetooth doesn't work anymore. Before (I think it was Ubuntu 11.04), I just followed instructions on this page and copied /lib/firmware/ath3k-2.fw to /lib/firmware/ath3k-1.fw and everything was fine. But in 12.04, there isn't any ath3k-2.fw in the /lib directory, so this method is not possible. Also, pressing Fn+F3 doesn't work. I would appreciate any help. Some further information (I hope it's enough): dmesg [ 23.063710] Bluetooth: Core ver 2.16 [ 23.063740] NET: Registered protocol family 31 [ 23.063743] Bluetooth: HCI device and connection manager initialized [ 23.063746] Bluetooth: HCI socket layer initialized [ 23.063747] Bluetooth: L2CAP socket layer initialized [ 23.063972] Bluetooth: SCO socket layer initialized [ 23.066930] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 23.066934] Bluetooth: BNEP filters: protocol multicast [ 23.068422] Bluetooth: RFCOMM TTY layer initialized [ 23.068428] Bluetooth: RFCOMM socket layer initialized [ 23.068430] Bluetooth: RFCOMM ver 1.11 lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 003: ID 046d:c05f Logitech, Inc. Bus 002 Device 004: ID 046d:c31c Logitech, Inc. Keyboard K120 for Business Bus 002 Device 005: ID 0402:9665 ALi Corp. Gateway Webcam hcitool dev Devices:

    Read the article

  • Connected to wireless, but no internet access

    - by boogaloo
    After installing Ubuntu 12.04 a week ago wireless internet had been working fine. It stopped working yesterday, however, and I'm at a loss for what to do even after scouring replies to similar posted problems. I have tried using Google's public DNS and turning off proxy settings on Firefox. I have used nm-tool and lshw to make sure my wireless device and driver are connected. If anyone can help me resolve this issue I would be extremely grateful! @kregerjd $ ping -c3 www.google.com ping: unknown host www.google.com @Alaa: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 $ ping -c4 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data From 192.168.1.104 icmp_seq=1 Destination Host Unavailable From 192.168.1.104 icmp_seq=2 Destination Host Unavailable --- 192.168.1.1 ping statistics --- 4 packets transmitted, 0 received, +2 errors, 100% packet loss, time 2998ms pipe 4

    Read the article

  • no boot menu or / mount point after installing Ubuntu 12.04

    - by Liz Kaiser
    I've installed Ubuntu 12.04 using a Live CD to a new Gateway computer with Windows 7. I used "Install Alongside Windows" option. But on restart there was no boot menu. It only starts into Windows. I looked at partitions using GParted (with Live CD) and it shows my new Ext 4 partition for Ubuntu as follows sda4 Extended, sda5 Ext 4, sda6 linux-swap But there is no / Mount Point listed for the sda5 partition. I did try Boot-Repair but it did nothing. So I've got 2 problems: no GRUB menu and no / Mount Point for my ext 4 partition. I'm so exasperated. Do I have to edit the fstab file to create a / mount point? (And that prospect really scares me.) And if I do, could someone give me step by step instructions. In order to avoid this detailed and scary stuff in the Terminal (which I really do not know very much about), I deleted the ubuntu partitions and started all over installing 12.04 again. But I'm left in the exact same situation now. Thanks for any help you all can provide. Is there an easy way out of this?

    Read the article

  • Network: Incoming connections work, outgoing fails

    - by anirvan
    i recently set up my own server at home to run Ubuntu 12.04 server ed. on booting up, i noticed that a message related to networking comes up, and the booting process pauses. the message read something like - waiting for network configuration and after a while - waiting another 60 seconds... on booting up, I realised that any command which requires a network connection was not working - ping, apt-get install, etc. on firing the ifup eth0 command, I get the error RTNETLINK answers: File exists. Failed to bring up eth0. I also realised, while searching the web for this problem, that this is probably one of the most common networking related issues - however, most of the questions are around setting up multiple IPs for the same machine. ifdown eth0 also fails, stating that eth0 is not configured. my /etc/network/interfaces file has a simple configuration for a static IP: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx gateway xx.xx.xx.xx dns-nameservers xx.xx.xx.xx The strangest part of this problem is that, while I can't connect to anything outside, I can ping to this particular server using the static IP configured in the interface file, and, i can even SSH into it! I'm really at ends here with this problem, and any guidance is much appreciated. Thanks!

    Read the article

  • How do I modify these VPN connection settings for Xfce?

    - by Dave M G
    I have signed up for a VPN (Virtual Private Network) service, and I configured it for use on my computer that runs Gnome Classic with the following instructions: In Terminal, install openvpn packages with sudo apt-get install network-manager-openvpn. 1. Restart the network manager with sudo restart network-manager 2. Run sudo wget https://www.xxxxxxx.com/ovpnconfigure.zip 3. Extract the files from the zip with unzip ovpnconfigure.zip. 4. Move cert.crt to /etc/openvpn 5. Open the Network Manager on the menu bar. 6. Choose add and select the OpenVPN connection type, and click Create. 7. Enter Private Internet Access SSL for the Connection Name. 8. Enter xxxxxx.xxxxxxxx.com for the Gateway 9. Select Password and enter your login credentials. 10. Browse and select the CA Certificate we saved in Step 3. 11. Choose Advanced and enable LZO Compression. 12. Apply and exit. 13. Connect using the Network Manager. It worked, but now I want to set up access to the same VPN service on another machine that runs Mythbuntu, which uses Xfce as its desktop manager. So every point from 5 on doesn't apply. How can I modify the above instructions so that I can get my VPN service working with Xfce. As a further note, while I can access the Xfce desktop directly if I need to, it's more convenient for me to access it via the command line and SSH from on of my other computers. A command line process would be ideal. (I looked for this, and found instructions only for PPTP access, whereas I need OpenVPN.)

    Read the article

  • Installed ubuntu over windows vista..cant reinstall windows

    - by Marcuz J Hinojoz
    I recently used the "compress hard drive" option within windows. i got the horid "boot mngr is compressed" after the restart. i tried booting my system back to windows vista but it doesnt read the cd that came with my computer. i tried going into system recovery and going back to a previous date but it didnt work. i kept pressing f8 but nothing. i installed ubuntu(the ubuntu cd worked but windows didnt?) i installed ubuntu so i could atleast get in my computer, and i still wasnt able to install windows from there. my hard drive got reformatted to a ext4? and windows cant install because it doesnt read it? im not sure, but its very frustrating. my computer is a gateway gt5668e windows vista home premium with sp1. im a graphic designer and use programs such as photoshop and cinema 4d to do my projects..i have been at a unfortunate halt with my work and i am really bummed out and dont know what to do... any help?

    Read the article

  • How to connect ethernet on ubuntu (with auto-detection by Ubuntu)

    - by user12285
    Do I need to post another thread for the same? If so, sorry. Yes, I saw that it's been well over six months but I have the same router SmartAX MT880d with ethernet, and the exact same problem, that is no internet even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. Sorry if I don't use the right (technical) terminology to express my issue. English is not my mother tongue. I'm a total beginner with ubuntu. My internet works great in Windows but does not work in Ubuntu. For 2 weeks, I've kept reading on the web and forums and the ubuntuguide.org to name a few but to no avail. Now I see no other solution but to ask for help. My problem is that as a beginner, I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files (eg: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm confused between putting figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem?? Is the subnet 255.255.255.0? Gateway 192.168.1.1. I'm confused as I can also see a different IP starting with 155131*** (is it an account number? no clue again) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

    - by Lorenzo
    I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

    Read the article

  • How to make ip Address static (eth0)

    - by Jordan Angelucci
    I'm having a really hard time configuring ubuntu 13.04 to have a static ip address. I have tried multiple solutions but everytime I reboot (can't do the network reset command because ubuntu freezes) I end up with no connection. Here is what I get when i type ifconfig into the terminal: eth0 Link encap:Ethernet HWaddr 10:bf:48:bc:07:cb inet addr:192.168.0.8 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::12bf:48ff:febc:7cb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1763067 errors:0 dropped:0 overruns:0 frame:0 TX packets:1024326 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2284491220 (2.2 GB) TX bytes:136809317 (136.8 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1840 errors:0 dropped:0 overruns:0 frame:0 TX packets:1840 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:185688 (185.6 KB) TX bytes:185688 (185.6 KB) I have also tried this: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.0.160 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 dns-nameservers 24.222.0.94 dns-nameservers 24.222.0.95 If anyone could help me it would be very much appreciated.

    Read the article

  • Wifi won't connect to certain networks

    - by Dave M G
    As I write this, I'm in a coffee shop on my laptop, and I am trying to connect to the free wifi network they offer. Every time I select their network from the wifi applet drop down menu, it connects for a second and then disconnects. At the same time, I have my Android phone with me, and it connects to the coffee shop's network without problem. There are a couple of people around me also using the same network with no issues. I asked the staff to check and as far as they can tell there is no problem with their router or anything. I have tried rebooting, but it has not made a difference. I have double and triple checked that I am using the correct WEP password. As an added wrinkle, when I connect to another network, it seems to connect (although I can't use them because they are paid gateway services). So I'm able to ask this question now because I have tethered my laptop to my phone, but it's slow and a workaround, not a solution. All indications are that it's a problem with my computer against this one network. Why would that be and how can I fix it?

    Read the article

  • New Versions of Whitepapers are available

    - by Anthony Shorten
    The set of whitepapers that are available are progressively being updated and republished to reflect new versions of the products as well new advice for existing customers. A number of whitepapers are now available that have been updated (the My Oracle Support Doc Id is indicated): What’s New in Oracle Utilities Application Framework V4 (Doc Id: 1177265.1) -  This has been updated for the latest facilities in Oracle Utilities Application Framework V4.1. Batch Best Practices (Doc Id: 836362.1) – This has been updated for newer advice including more details of how CLUSTERED mode works, how to migrate to CLUSTERED mode and some configuration examples to cover typical configuration scenarios. Oracle Utilities Application Framework Architecture Guidelines (Doc Id: 807068.1) – This has been updated to reflect additional architecture advice. Performance Troubleshooting Guides (Doc Id: 560382.1) – This has been updated for the latest facilities in Oracle Utilities Application Framework V4.1 and includes additional techniques that have been used by customers to track performance. The whitepapers apply to all Oracle Utilities Application Framework Products which at the present time includes: Oracle Utilities Customer Care And Billing (V2.x) Oracle Enterprise Taxation Management (V2.x) Oracle Utilities Business Intelligence (V2.x) Oracle Utilities Meter Data Management (V2.x) Oracle Utilities Mobile Workforce Management (V2.x) Oracle Utilities Smart Grid Gateway (V2.x) Additional whitepapers and updates will be posted as they are available.

    Read the article

  • How to connect Ethernet via a Huawei Smart AXMT880s modem (with auto-detection)?

    - by user12285
    It's been well over six months but I have the same router SmartAX MT880d with Ethernet, and the exact same problem : no internet, even though I can successfully reach the modem settings page by entering 192.168.1.1 in Firefox. I'm a total beginner with Ubuntu. My internet works great in Windows but does not work in Ubuntu. Sorry if I don't use the right (technical) terminology to explain my issue. English is not my mother tongue. For 2 weeks, I've been doing reading on the web and forums and the ubuntuguide.org to name a few, but to no avail. Now I see no other solution but to ask for help. My problem is that I can't find a way to put the right digits in the right place because I don't know what numbers I need to put in what files. E.g.: do I need to use DHCP? or a static IP address? No clue whatsoever. I'm concerned that I might put figures in the wrong spaces. For example, is the modem/router's IP exactly 192.168.1.1 for Huawei Smart AXMT880d modem? Is the subnet 255.255.255.0? Gateway 192.168.1.1? I'm confused as I can also see a different IP starting with 155131*** (is it an account number?) on my contract with Huawei (a Chinese ISP). Apart from calling 911, what other numbers do I need to put in and where? How do I check that all the numbers have been entered correctly in every appropriate space before trying to connect the Internet?

    Read the article

  • ubuntu 12.04 installer does not recognize drive partitions

    - by endless forms
    I recently purchased a new HP Pavilion HPE desktop running Windows 7. I am trying to install a dual-boot system with 12.04. However, when I run the LiveCD I only get as far as the "Install" window where you can select the partitions for your drives. On the bottom where it says "device for boot loader installation" I have "/dev/sda" and cannot select any other devices. All the options to change the drives are greyed out, most likely because there are no drives in the window. I partitioned my largest drive using the tools within Windows, then booted into the CD, but nothing shows up. I then used Gparted to change the new space from unallocated to an /ext2, and still nothing shows up. The installer does not recognize anything, but when I go into an Ubuntu session and use the disk utility manager I can see the partitions I made. Anything I do has to be done outside of the installer. I have no files on this new computer, so this is the perfect time to install a parallel OS. I would like avoid completely reinstalling Windows, however. I've been over the forums many times, but all the answers I've found have not worked for me. I also tried flagging the new, empty partition as boot, but that screwed Windows up. Also, the WUBI installer hits the same point and quits. I know that the disk itself is fine because I just made another dual boot system on a Gateway PC. This makes me think something within this computer is preventing the installer from "seeing" the drives. Any help would be much appreciated! Edit in response: The main part of the partitioning window shows no partitions, everything is blank. There is no way to add partitions, and all the buttons are useless. I've tried defragging my drive multiple times, and I also used the same disk to dual-boot another PC with no problems, so it's not the disk, it's definitely the computer.

    Read the article

  • curl blocked at TMG firewall

    - by jemtube100
    i using TMG (threat management gateway) firewall at my web server. when i try to use Curl from outside, this firewall was blocked the connection. what rule/setting that i need to create at TMG to allow it. the error state as below : Refresh page: Search for the page again by clicking the Refresh button. The timeout may have occurred due to Internet congestion. Check spelling: Check that you typed the Web page address correctly. The address may have been mistyped. Access from a link: If there is a link to the page you are looking for, try accessing the page from that link. </UL> <HR color=#c0c0c0 noShade> <P id=L_defaultr_11>Technical Information (for support personnel)</P> <UL> <LI id=L_defaultr_12>Error Code: 403 Forbidden. The server denied the specified Uniform Resource Locator (URL). Contact the server administrator. (12202)

    Read the article

  • How can I speed up boot on one of my machines?

    - by Korneel Bouman
    I have a Gateway all in one machine (2 gig Intel Core 2 Duo T7250 dual core processor, 2 gig RAM - full specs) on which I installed 10.10. Once it has booted it's fine, but it takes forever to boot. This is what happens: 1. Boot starts with cursor flashing for about 10-15 seconds 2. Cursor disappears for 1.5 - 2 minutes 3. Cursor reappears, blinks a few seconds more, boot finishes in another 10 seconds 4. Login screen I have another machine with marginal better specs that boots up in no time (basically the above minus the two minute delay). Things I've done: enabled verbose mode for grub nothing is showing until after 2 minute pause. checked syslog last message before pause is a message from alsa saying the process is already running (or something similar... going from memory here...) It could be something sound related as the built in speakers are not working (sound card is recognized though and headphones work). Anyway, it's not the end of the world, but it's annoying and I'd like to know what's going on... Many thanks, and let me know if more info is needed.

    Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >