Search Results

Search found 11834 results on 474 pages for 'radio group'.

Page 85/474 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• e2fsck / resize2fs problems

  - by BlakBat

  I've got 6 drives (each 1.5T, all same model and firmware revision) that are part of a RAID5 array. The RAID5 makes a LVM volume group and a logical group. The latter contains only one ext3 partition. I've recently ran: e2fsck -f /dev/vg03/lv01 && resize2fs -M /dev/vg03/lv01 which exited without an error. Now when I try to mount /dev/vg03/lv01 I get: EXT3-fs error (device dm-0): ext3_check_descriptors: Block bitmap for group 30533 not in group (block 1000532368)! EXT3-fs: group descriptors corrupted! How do I get out of this predicament? This is all the info I can currently give you: fdisk -l /dev/sd[cdefgh] shows (correctly) that they are "Linux raid autodetect" but fdisk now shows: fdisk -l /dev/md0 Disk /dev/md0: 7501.5 GB, 7501495664640 bytes ... Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table (instead of a LVM type partition) fdisk -l /dev/vg03/lv01 Disk /dev/vg03/lv01: 7501.5 GB, 7501491732480 bytes ... Disk identifier: 0x00000000 Disk /dev/vg03/lv01 doesn't contain a valid partition table (instead of a ext3 type partition) I've tried: e2fsck -fy /dev/vg03/lv01 e2fsck 1.41.12 (17-May-2010) e2fsck: Group descriptors look bad... trying backup blocks... Block bitmap for group 30533 is not in group. (block 1000532368) Relocate? yes Inode bitmap for group 30533 is not in group. (block 1000532369) Relocate? yes Pass 1: Checking inodes, blocks, and sizes Relocating group 30533's block bitmap to 1000524246... Error allocating 1 contiguous block(s) in block group 30533 for inode bitmap: Could not allocate block in ext2 filesystem e2fsck: aborted Extra information I can give you: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active (auto-read-only) raid5 sdg1[0] sdh1[5] sdf1[4] sde1[3] sdc1[2] sdd1[1] 7325679360 blocks level 5, 128k chunk, algorithm 2 [6/6] [UUUUUU] bitmap: 1/175 pages [4KB], 4096KB chunk unused devices: Lastly, all smartctl tests (short and extendend) showed no errors on any of the disks. Should I try to resize2fs to grow /dev/vg03/lv01 and redo a e2fsck ? Should I cfdisk /dev/md0 and /dev/vg03/lv01 back to their real types? Thanks in advance for all and any help. 2011-09-20 UPDATE I issued the following commands and was able to remount the partition, but by viewing the size (df) of before and after, it seems that 1Tb of data have gone missing. By checking the MD5SUMS (from an old backup) of some files with the "same" files from the remounted partition, some errors have been detected. Commands issued to remount the partition were: dumpe2fs /dev/vg03/lv01 Block count: 1000491435<br /> Block size: 4096<br /> tune2fs -O ^has_journal /dev/vg03/lv01 resize2fs -p /dev/vg03/lv01 dumpe2fs /dev/vg03/lv01 Block count: 1831418880<br /> Block size: 4096<br /> mount -o ro,noatime /dev/vg03/lv01 /mnt/raid OK... but files have been damaged / gone missing.

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• haproxy: Is there a way to group acls for greater efficiency?

  - by user41356

  I have some logic in a frontend that routes to different backends based on both the host and the url. Logically it looks like this: if hdr(host) ends with 'a.domain.com': if url starts with '/dir1/': use backend domain.com/dir1/ elif url starts with '/dir2/': use backend domain.com/dir2/ # ... else if ladder repeats on different dirs elif hdr(host) ends with 'b.domain.com': # another else if ladder exactly the same as above # ... # ... else if ladder repeats like this on different domains Is there a way to group acls to avoid having to repeatedly check the domain acl? Obviously there needs to be a use backend statement for each possibility, but I don't want to have to check the domain over and over because it's very inefficient. In other words, I want to avoid this: use backend domain.com/url1/ if acl-domain.com and acl-url1 use backend domain.com/url2/ if acl-domain.com and acl-url2 use backend domain.com/url3/ if acl-domain.com and acl-url3 # tons more possibilities below because it has to keep checking acl-domain.com. This is particularly an issue because I have specific rules for subdomains such as a.domain.com and b.domain.com, but I want to fall back on the most common case of *.domain.com. That means every single rule that uses a specific subdomain must be checked prior to *.domain.com which makes it even more inefficient for the common case.

  Read the article

• Why can't I browse my D: drive, even if I'm in the Administrators group?

  - by Nic Waller

  My fileserver running Windows Server 2008 has two logical drives; the C: drive contains all of the system and application data, and the D: drive contains all of the business data. There are several shares on the top level of the D: drive that are working fine. However... When logged into the fileserver interactively via Remote Desktop, only the Domain Administrator and local Administrator accounts can browse the D: drive. I set up an account called "Maintenance" and added it to the local Administrators group, but when logged in with this user, I can't browse into the D: drive. The D: drive has the following permissions ACL: Full Access - SYSTEM Full Access - MACHINE\Administrators It won't even let me view the ACL for the E: drive. So I tried taking ownership of the E: drive, then I can read the ACL, and "Effective Permissions" says that I have full access. But I still get this error message. Location is not available D:\ is not accessible. Access is denied. Here's a screenshot proving that I get access denied even when I have Full Access. http://www.getdropbox.com/gallery/2319942/1/errors?h=2bd644

  Read the article

• Twitter Bootstrap modal spans, side-by-side divs and "control-group"?

  - by Federico Stango

  I'm trying my best to have a good looking modal login form but for some reasons it seems that no matter how I nest divs, I cannot obtain the proper shape. What I need is a big "lock" image side-by-side with a username/password form. The best I could do adds a horizontal scroller by the modal bottom and shows the input gadgets fairly distant from the image partly hidden on the right side of the modal canvas. Inspecting with FireBug it seems that the spans in row-fluid are ok but the "control-label" and "controls" class adds way too much space on the left by width (for the labels) and margin-left (for the controls). How would you solve it? Am I doing something wrong with divs and classes nesting? This is the current modal without the main wrapper as it gets added by some js code that loads modal contents through ajax: <form class="form-horizontal" id="login" name="login" method="post" action="<?php echo site_url('user/login'); ?>"> <div class="modal-header"> <button type="button" class="close" data-dismiss="modal" aria-hidden="true">&times;</button> <h3>Login</h3> </div> <div class="modal-body"> <?php if ( isset($error) ) { ?> <div class="row"> <div class="alert alert-error"> <strong>Warning!</strong> <?php echo $error; ?> </div> </div> <?php } ?> <div class="row-fluid"> <div class="span4"> <img src="skins/frontend/base/images/lock.png" width="96px" height="96px" /> </div> <div class="span8"> <div class="control-group"> <label class="control-label" for="email">Email</label> <div class="controls"><input type="text" placeholder="Type your email" id="email" name="email" /></div> <?php echo form_error('email', '<div id="error_email" class="alert alert-error">* ', '</div>'); ?> </div> <div class="control-group"> <label class="control-label" for="password">Password</label> <div class="controls"><input type="password" placeholder="Password" id="password" name="password" /></div> <?php echo form_error('password', '<div id="error_password" class="alert alert-error">* ', '</div>'); ?> </div> <div class="control-group"> <div class="controls"><label class="checkbox inline"><input type="checkbox" id="remember" name="remember" checked="checked" />&nbsp;Remember Me</label></div> </div> </div> </div> </div> <div class="modal-footer"> <button type="submit" class="btn btn-primary">Login</button> </div> </form> Just don't take into account the php code you see... :) Thanks in advance for all the support you can give! Federico

  Read the article

• SSRS Export to Excel not working through VPN (Juniper SA4000)

  - by Veynom

  We have a SharePoint (MOSS 2007 on Win2003 R2) with SSRS reports (from SQL 2005) embedded in it. When we connect to the SharePoint portal through our VPN (firewall is Juniper SA4000) and using Internet Explorer (6, 7, and 8) and try to export any SSRS report under Excel, we get an error message: Internet Explorer cannot download . Internet Explorer was not able to open the internet site. The requested site is either unavailable or cannot be found. Please try again later. When not using the VPN (LAN from the office), everything (exporting under Excel) works fine. When using Firefox through the VPN, it works fine. When exporting to any other format (pdf or text or whatever), everything is fine under both IE and FF. Our firewall people suspect something in SSRS/MOSS/Office. Our MOSS consultants suspect something in the firewall Juniper SA4000. When using Fiddler and when not connected through VPN, I see the following traffic once i click on the "Export button": (Response was a request for client credentials) GET /ReportServer/Reserved.ReportViewerWebControl.axd?ExecutionID=j1pqbvbqkb34qf45fhlgnx55&ControlID=733607a7d607476abb1e6b8794202158&Culture=127&UICulture=9&ReportStack=1&OpType=Export&FileName=Product+Application+Report&ContentDisposition=OnlyHtmlInline&Format=EXCEL HTTP/1.1 Accept: */* Accept-Language: en-US,fr-be;q=0.5 User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; GTB5; .NET CLR 2.0.50727; .NET CLR 1.1.4322; InfoPath.2; .NET CLR 3.0.04506.648; .NET CLR 3.5.21022; MS-RTC LM 8; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: r1frchcurdb01.r1.group.corp HTTP/1.1 401 Unauthorized Content-Length: 1656 Content-Type: text/html Server: Microsoft-IIS/6.0 WWW-Authenticate: Negotiate WWW-Authenticate: NTLM X-Powered-By: ASP.NET Date: Mon, 08 Jun 2009 09:25:21 GMT Proxy-Support: Session-Based-Authentication then (Generic Response successful): GET /ReportServer/Reserved.ReportViewerWebControl.axd?ExecutionID=j1pqbvbqkb34qf45fhlgnx55&ControlID=733607a7d607476abb1e6b8794202158&Culture=127&UICulture=9&ReportStack=1&OpType=Export&FileName=Product+Application+Report&ContentDisposition=OnlyHtmlInline&Format=EXCEL HTTP/1.1 Accept: */* Accept-Language: en-US,fr-be;q=0.5 User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; GTB5; .NET CLR 2.0.50727; .NET CLR 1.1.4322; InfoPath.2; .NET CLR 3.0.04506.648; .NET CLR 3.5.21022; MS-RTC LM 8; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Connection: Keep-Alive Host: r1frchcurdb01.r1.group.corp Authorization: Negotiate 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 HTTP/1.1 200 OK Date: Mon, 08 Jun 2009 09:25:21 GMT Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET WWW-Authenticate: Negotiate oYGgMIGdoAMKAQChCwYJKoZIgvcSAQICooGIBIGFYIGCBgkqhkiG9xIBAgICAG9zMHGgAwIBBaEDAgEPomUwY6ADAgEXolwEWm70xlMp4oj/PyvriNMeNDigow6/MX2DpaYQdBfGkiF0Dcc323tHLRBxBL03QpvwdGBxZGAJI6V1G8sc/lVBzhlCNsZkbJcNfnMNgOgc7UPrz+ZVav/EVm3sDQ== X-AspNet-Version: 2.0.50727 Content-Disposition: attachment; filename="Product Application Report.xls" Cache-Control: private Expires: Mon, 08 Jun 2009 09:24:21 GMT Content-Type: application/vnd.ms-excel Content-Length: 23012 When using the VPN, I see no traffic in Fiddler and the error message is displayed before anything else. Update 17/06/2009: I could get a hand on some logs from our SA4000. Maybe this could help more. Info PTR23232 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Start Policy [WEBURL/PROTOCOL] evaluation for resource http://<DB server>:80/ReportServer/Reserved.ReportViewerWebControl.axd?ExecutionID=rua1g355tic24245f2e13lim&ControlID=44168efcd36e461493f7a69962580b91&Culture=127&UICulture=9&ReportStack=1&OpType=Export&FileName=Product+Application+Report&ContentDisposition=OnlyHtmlInline&Format=EXCEL Info PTR23233 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Applying Policy [Enable HTTP 1.1]... Info PTR23240 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Resource filter [http://nsrvnts2:80/*] does not match Info PTR23240 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Resource filter [http://nsrvnts3:80/*] does not match Info PTR23233 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Applying Policy [Disable HTTP 1.1]... Info PTR23239 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Action [HTTP 1.0] is returned Info PTR23234 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Policy [Disable HTTP 1.1] applies to resource Info PTR23308 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Skip Policy [WEBURL/COMPRESSION] evaluation because Compression option is not enabled Info PTR23232 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Start Policy [WEBURL/WEBPDSID] evaluation for resource http://<DB server>:80/ReportServer/Reserved.ReportViewerWebControl.axd?ExecutionID=rua1g355tic24245f2e13lim&ControlID=44168efcd36e461493f7a69962580b91&Culture=127&UICulture=9&ReportStack=1&OpType=Export&FileName=Product+Application+Report&ContentDisposition=OnlyHtmlInline&Format=EXCEL Info PTR23233 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Applying Policy [Corporate BI Portal]... Info PTR23240 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Resource filter [http://<SharePoint>:80/*] does not match Info PTR23240 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - Resource filter [http://<SharePoint>/*] does not match Info PTR23235 2009/06/15 17:22:38 - <SA4000> - [<SA4000 IP>] - <user>[SA4000 group names] - No Policy applies to resource Any tip welcome. :)

  Read the article

• Need help making site available externally

  - by White Island

  I'm trying to open a hole in the firewall (ASA 5505, v8.2) to allow external access to a Web application. Via ASDM (6.3?), I've added the server as a Public Server, which creates a static NAT entry [I'm using the public IP that is assigned to 'dynamic NAT--outgoing' for the LAN, after confirming on the Cisco forums that it wouldn't bring everyone's access crashing down] and an incoming rule "any... public_ip... https... allow" but traffic is still not getting through. When I look at the log viewer, it says it's denied by access-group outside_access_in, implicit rule, which is "any any ip deny" I haven't had much experience with Cisco management. I can't see what I'm missing to allow this connection through, and I'm wondering if there's anything else special I have to add. I tried adding a rule (several variations) within that access-group to allow https to the server, but it never made a difference. Maybe I haven't found the right combination? :P I also made sure the Windows firewall is open on port 443, although I'm pretty sure the current problem is Cisco, because of the logs. :) Any ideas? If you need more information, please let me know. Thanks Edit: First of all, I had this backward. (Sorry) Traffic is being blocked by access-group "inside_access_out" which is what confused me in the first place. I guess I confused myself again in the midst of typing the question. Here, I believe, is the pertinent information. Please let me know what you see wrong. access-list acl_in extended permit tcp any host PUBLIC_IP eq https access-list acl_in extended permit icmp CS_WAN_IPs 255.255.255.240 any access-list acl_in remark Allow Vendor connections to LAN access-list acl_in extended permit tcp host Vendor any object-group RemoteDesktop access-list acl_in remark NetworkScanner scan-to-email incoming (from smtp.mail.microsoftonline.com to PCs) access-list acl_in extended permit object-group TCPUDP any object-group Scan-to-email host NetworkScanner object-group Scan-to-email access-list acl_out extended permit icmp any any access-list acl_out extended permit tcp any any access-list acl_out extended permit udp any any access-list SSLVPNSplitTunnel standard permit LAN_Subnet 255.255.255.0 access-list nonat extended permit ip VPN_Subnet 255.255.255.0 LAN_Subnet 255.255.255.0 access-list nonat extended permit ip LAN_Subnet 255.255.255.0 VPN_Subnet 255.255.255.0 access-list inside_access_out remark NetworkScanner Scan-to-email outgoing (from scanner to Internet) access-list inside_access_out extended permit object-group TCPUDP host NetworkScanner object-group Scan-to-email any object-group Scan-to-email access-list inside_access_out extended permit tcp any interface outside eq https static (inside,outside) PUBLIC_IP LOCAL_IP[server object] netmask 255.255.255.255 I wasn't sure if I needed to reverse that "static" entry, since I got my question mixed up... and also with that last access-list entry, I tried interface inside and outside - neither proved successful... and I wasn't sure about whether it should be www, since the site is running on https. I assumed it should only be https.

  Read the article

• London User Group Meetings this week (19th/20th May); 26th May-Agile Data Warehousing; 17th June-Kim

  - by tonyrogerson

  Got two user group meetings in London for you, we've also started the Cuppa Corner sessions - the first 3 are up on the site - A trip to First Normal Form, Lookup and Cache Transform in SSIS and Pipeline Limiter in SSIS - we are aiming for at least one per week. WhereScape are doing a breakfast meeting on Agile techniques to Data Warehousing and Kimberly Tripp and Paul Randal are over in June for a 1 day master class. Finally a 3 day performance and monitoring workshop on 22- 24th June in London...(read more)

  Read the article

• Desktop Fun: Runic Style Fonts

  - by Asian Angel

  Most of the time regular fonts are just what you need for documents, invitations, or adding text to images. But what if you are in the mood for something unusual or unique to add that perfect touch? If you like older runic style writing, then enjoy finding some new favorites for your collection with our Runic Style Fonts collection. Temple photo by ShinyShiny. Note: To manage the fonts on your Windows 7, Vista, & XP systems see our article here. The Runic Style Fonts Sable Download Worn Manuscript Download JSL Ancient Download Antropos Download Cave Gyrl Download The Roman Runes Alliance Download Ancient Geek Download Troll Download Runish Quill MK *includes two font types Download DS RUNEnglish 2 Download Runes Written *includes two font types Download Wolves And Ravens Download Art Greco Download Dalek Download Glagolitic AOE Download Linear B Download Cartouche Download Greywolf Glyphs *includes 62 individual characters Note: This group represents A – Z in all capital letters. Note: This group represents A – Z in all lower case letters. Note: This group represents the numbers 0 – 9. Download Africain *includes 62 individual characters Note: This group represents A – Z in all capital letters. Note: This group represents A – Z in all lower case letters. Note: This group represents the numbers 0 – 9. Download Cave Writings *includes 52 individual characters Note: This group represents A – Z in all capital letters. Note: This group represents A – Z in all lower case letters. Download For more great ways to customize your computer be certain to look through our Desktop Fun section. Latest Features How-To Geek ETC HTG Projects: How to Create Your Own Custom Papercraft Toy How to Combine Rescue Disks to Create the Ultimate Windows Repair Disk What is Camera Raw, and Why Would a Professional Prefer it to JPG? The How-To Geek Guide to Audio Editing: The Basics How To Boot 10 Different Live CDs From 1 USB Flash Drive The 20 Best How-To Geek Linux Articles of 2010 Five Sleek Audi R8 Car Themes for Chrome and Iron MS Notepad Replacement Metapad Returns with a New Beta Version Spybot Search and Destroy Now Available as a Portable App (PortableApps.com) ShapeShifter: What Are Dreams? [Video] This Computer Runs on Geek Power Wallpaper Bones, Clocks, and Counters; A Look at the First 35,000 Years of Computing

  Read the article

• How to create a virtual network with Azure Connect

  - by Herve Roggero

  If you are trying to establish a virtual network between machines located in disparate networks, you can either use VPN, Virtual Network or Azure Connect. If you want to establish a connection between machines located in Windows Azure, you should consider using the Virtual Network service. If you want to establish a connection between local machines and Virtual Machines in Windows Azure, you may be able to use your existing VPN device (assuming you have one), as long as the device is supported by Microsoft. If the VPN device you are using isn’t supported, or if you are trying to create a virtual network between machines from disparate networks (such as machines located in another cloud provider), you can use Azure Connect. This blog post explains how Azure Connect can help you create virtual networks between multiple servers in the cloud, various servers in different cloud environments, and on-premise. Note: Azure Connect is currently in Technical Preview. About Azure Connect Let’s do a quick review of Azure Connect. This technology implements an IPSec tunnel from machines to to a relay service located in the Microsoft cloud (Azure). So in essence, Azure Connect doesn’t provide a point-to-point connection between machines; the network communication is tunneled through the relay service. The relay service in turn offers a mechanism to enforce basic communication rules that you define through Groups. We will review this later. You could network two or more VMs in the Azure cloud (although you should consider using a Virtual Network if you go this route), or servers in the Azure cloud and other machines in the Amazon cloud for example, or even two or more on-premise servers located in different locations for which a direct network connection is not an option. You can place any number of machines in your topology. Azure Connect gives you great flexibility on how you want to build your virtual network across various environments. So Azure Connect makes sense when you want to: Connect machines located in different cloud providers Connect on-premise machines running in different locations Connect Azure VMs with on-premise (if you do not have a VPN device, or if your device is not supported) Connect Azure Roles (Worker Roles, Web Roles) with on-premise servers or in other cloud providers The diagram below shows you a high level network topology that involves machines in the Windows Azure cloud, other cloud providers and on-premise. You should note that the only required component in this diagram is the Relay itself. The other machines are optional (although your network is useful only if you have two or more machines involved). Relay agents are currently available in three geographic areas: US, Europe and Asia. You can change which region you want to use in the Windows Azure management portal. High Level Network Topology With Azure Connect Azure Connect Agent Azure Connect establishes a virtual network and creates virtual adapters on your machines; these virtual adapters communicate through the Relay using IPSec. This is achieved by installing an agent (the Azure Connect Agent) on all the machines you want in your network topology. However, you do not need to install the agent on Worker Roles and Web Roles; that’s because the agent is already installed for you. Any other machine, including Virtual Machines in Windows Azure, needs the agent installed.  To install the agent, simply go to your Windows Azure portal (http://windows.azure.com) and click on Networks on the bottom left panel. You will see a list of subscriptions under Connect. If you select a subscription, you will be able to click on the Install Local Endpoint icon on top. Clicking on this icon will begin the download and installation process for the agent. Activating Roles for Azure Connect As previously mentioned, you do not need to install the Azure Connect Agent on Worker Roles and Web Roles because it is already loaded. However, you do need to activate them if you want the roles to participate in your network topology. To do this, you will need to click on the Get Activation Token icon. The activation token must then be copied and placed in the configuration file of your roles. For more information on how to perform this step, visit MSDN at http://msdn.microsoft.com/en-us/library/windowsazure/gg432964.aspx. Firewall Rules Note that specific firewall rules must exist to allow the agent to communicate through the Relay. You will need to allow TCP 443 and ICMPv6. For additional information, please visit MSDN at http://msdn.microsoft.com/en-us/library/windowsazure/gg433061.aspx. CA Certificates You can optionally require agents to sign their activation request with the Relay using a trusted certificate issued by a Certificate Authority (CA). Click on Activation Options to learn more. Groups To create your network topology you must first create a group. A group represents a logical container of endpoints (or machines) that can communicate through the Relay. You can create multiple groups allowing you to manage network communication differently. For example you could create a DEVELOPMENT group and a PRODUCTION group. To add an endpoint you must first install an agent that will create a virtual adapter on the machine on which it is installed (as discussed in the previous section). Once you have created a group and installed the agents, the machines will appear in the Windows Azure management portal and you can start assigning machines to groups. The next figure shows you that I created a group called LocalGroup and assigned two machines (both on-premise) to that group. Groups and Computers in Azure Connect As I mentioned previously you can allow these machines to establish a network connection. To do this, you must enable the Interconnected option in the group. The following diagram shows you the definition of the group. In this topology I chose to include local machines only, but I could also add worker roles and web roles in the Azure Roles section (you must first activate your roles, as discussed previously). You could also add other Groups, allowing you to manage inter-group communication. Defining a Group in Azure Connect Testing the Connection Now that my agents have been installed on my two machines, the group defined and the Interconnected option checked, I can test the connection between my machines. The next screenshot shows you that I sent a PING request to DEVLAP02 from DEVDSK02. The PING request was successful. Note however that the time is in the hundreds of milliseconds on average. That is to be expected because the machines are connecting through the Relay located in the cloud. Going through the Relay introduces an extra hop in the communication chain, so if your systems rely on high performance, you may want to conduct some basic performance tests. Sending a PING Request Through The Relay Conclusion As you can see, creating a network topology between machines using the Azure Connect service is simple. It took me less than five minutes to create the above configuration, including the time it took to install the Azure Connect agents on the two machines. The flexibility of Azure Connect allows you to create a virtual network between disparate environments, as long as your operating systems are supported by the agent. For more information on Azure Connect, visit the MSDN website at http://msdn.microsoft.com/en-us/library/windowsazure/gg432997.aspx. About Herve Roggero Herve Roggero, Windows Azure MVP, is the founder of Blue Syntax Consulting, a company specialized in cloud computing products and services. Herve's experience includes software development, architecture, database administration and senior management with both global corporations and startup companies. Herve holds multiple certifications, including an MCDBA, MCSE, MCSD. He also holds a Master's degree in Business Administration from Indiana University. Herve is the co-author of "PRO SQL Azure" from Apress and runs the Azure Florida Association (on LinkedIn: http://www.linkedin.com/groups?gid=4177626). For more information on Blue Syntax Consulting, visit www.bluesyntax.net. Special Thanks I would like thank those that helped me figure out how Azure Connect works: Marcel Meijer - http://blogs.msmvps.com/marcelmeijer/ Michael Wood - Http://www.mvwood.com Glenn Block - http://www.codebetter.com/glennblock Yves Goeleven - http://cloudshaper.wordpress.com/ Sandrino Di Mattia - http://fabriccontroller.net/ Mike Martin - http://techmike2kx.wordpress.com

  Read the article

• mounting ext4 fs with block size of 65536

  - by seaquest

  I am doing some benchmarking on EXT4 performance on Compact Flash media. I have created an ext4 fs with block size of 65536. however I can not mount it on ubuntu-10.10-netbook-i386. (it is already mounting ext4 fs with 4096 bytes of block sizes) According to my readings on ext4 it should allow such big block sized fs. I want to hear your comments. root@ubuntu:~# mkfs.ext4 -b 65536 /dev/sda3 Warning: blocksize 65536 not usable on most systems. mke2fs 1.41.12 (17-May-2010) mkfs.ext4: 65536-byte blocks too big for system (max 4096) Proceed anyway? (y,n) y Warning: 65536-byte blocks too big for system (max 4096), forced to continue Filesystem label= OS type: Linux Block size=65536 (log=6) Fragment size=65536 (log=6) Stride=0 blocks, Stripe width=0 blocks 19968 inodes, 19830 blocks 991 blocks (5.00%) reserved for the super user First data block=0 1 block group 65528 blocks per group, 65528 fragments per group 19968 inodes per group Writing inode tables: done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 37 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. root@ubuntu:~# tune2fs -l /dev/sda3 tune2fs 1.41.12 (17-May-2010) Filesystem volume name: <none> Last mounted on: <not available> Filesystem UUID: 4cf3f507-e7b4-463c-be11-5b408097099b Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 19968 Block count: 19830 Reserved block count: 991 Free blocks: 18720 Free inodes: 19957 First block: 0 Block size: 65536 Fragment size: 65536 Blocks per group: 65528 Fragments per group: 65528 Inodes per group: 19968 Inode blocks per group: 78 Flex block group size: 16 Filesystem created: Sat Feb 5 14:39:55 2011 Last mount time: n/a Last write time: Sat Feb 5 14:40:02 2011 Mount count: 0 Maximum mount count: 37 Last checked: Sat Feb 5 14:39:55 2011 Check interval: 15552000 (6 months) Next check after: Thu Aug 4 14:39:55 2011 Lifetime writes: 70 MB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: afb5b570-9d47-4786-bad2-4aacb3b73516 Journal backup: inode blocks root@ubuntu:~# mount -t ext4 /dev/sda3 /mnt/ mount: wrong fs type, bad option, bad superblock on /dev/sda3, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• mdadm: Win7-install created a boot partition on one of my RAID6 drives. How to rebuild?

  - by EXIT_FAILURE

  My problem happened when I attempted to install Windows 7 on it's own SSD. The Linux OS I used which has knowledge of the software RAID system is on a SSD that I disconnected prior to the install. This was so that windows (or I) wouldn't inadvertently mess it up. However, and in retrospect, foolishly, I left the RAID disks connected, thinking that windows wouldn't be so ridiculous as to mess with a HDD that it sees as just unallocated space. Boy was I wrong! After copying over the installation files to the SSD (as expected and desired), it also created an ntfs partition on one of the RAID disks. Both unexpected and totally undesired! . I changed out the SSDs again, and booted up in linux. mdadm didn't seem to have any problem assembling the array as before, but if I tried to mount the array, I got the error message: mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so dmesg: EXT4-fs (md0): ext4_check_descriptors: Block bitmap for group 0 not in group (block 1318081259)! EXT4-fs (md0): group descriptors corrupted! I then used qparted to delete the newly created ntfs partition on /dev/sdd so that it matched the other three /dev/sd{b,c,e}, and requested a resync of my array with echo repair > /sys/block/md0/md/sync_action This took around 4 hours, and upon completion, dmesg reports: md: md0: requested-resync done. A bit brief after a 4-hour task, though I'm unsure as to where other log files exist (I also seem to have messed up my sendmail configuration). In any case: No change reported according to mdadm, everything checks out. mdadm -D /dev/md0 still reports: Version : 1.2 Creation Time : Wed May 23 22:18:45 2012 Raid Level : raid6 Array Size : 3907026848 (3726.03 GiB 4000.80 GB) Used Dev Size : 1953513424 (1863.02 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon May 26 12:41:58 2014 State : clean Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 4K Name : okamilinkun:0 UUID : 0c97ebf3:098864d8:126f44e3:e4337102 Events : 423 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 8 32 1 active sync /dev/sdc 2 8 48 2 active sync /dev/sdd 3 8 64 3 active sync /dev/sde Trying to mount it still reports: mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so and dmesg: EXT4-fs (md0): ext4_check_descriptors: Block bitmap for group 0 not in group (block 1318081259)! EXT4-fs (md0): group descriptors corrupted! I'm a bit unsure where to proceed from here, and trying stuff "to see if it works" is a bit too risky for me. This is what I suggest I should attempt to do: Tell mdadm that /dev/sdd (the one that windows wrote into) isn't reliable anymore, pretend it is newly re-introduced to the array, and reconstruct its content based on the other three drives. I also could be totally wrong in my assumptions, that the creation of the ntfs partition on /dev/sdd and subsequent deletion has changed something that cannot be fixed this way. My question: Help, what should I do? If I should do what I suggested , how do I do that? From reading documentation, etc, I would think maybe: mdadm --manage /dev/md0 --set-faulty /dev/sdd mdadm --manage /dev/md0 --remove /dev/sdd mdadm --manage /dev/md0 --re-add /dev/sdd However, the documentation examples suggest /dev/sdd1, which seems strange to me, as there is no partition there as far as linux is concerned, just unallocated space. Maybe these commands won't work without. Maybe it makes sense to mirror the partition table of one of the other raid devices that weren't touched, before --re-add. Something like: sfdisk -d /dev/sdb | sfdisk /dev/sdd Bonus question: Why would the Windows 7 installation do something so st...potentially dangerous? Update I went ahead and marked /dev/sdd as faulty, and removed it (not physically) from the array: # mdadm --manage /dev/md0 --set-faulty /dev/sdd # mdadm --manage /dev/md0 --remove /dev/sdd However, attempting to --re-add was disallowed: # mdadm --manage /dev/md0 --re-add /dev/sdd mdadm: --re-add for /dev/sdd to /dev/md0 is not possible --add, was fine. # mdadm --manage /dev/md0 --add /dev/sdd mdadm -D /dev/md0 now reports the state as clean, degraded, recovering, and /dev/sdd as spare rebuilding. /proc/mdstat shows the recovery progress: md0 : active raid6 sdd[4] sdc[1] sde[3] sdb[0] 3907026848 blocks super 1.2 level 6, 4k chunk, algorithm 2 [4/3] [UU_U] [>....................] recovery = 2.1% (42887780/1953513424) finish=348.7min speed=91297K/sec nmon also shows expected output: ¦sdb 0% 87.3 0.0| > |¦ ¦sdc 71% 109.1 0.0|RRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR > |¦ ¦sdd 40% 0.0 87.3|WWWWWWWWWWWWWWWWWWWW > |¦ ¦sde 0% 87.3 0.0|> || It looks good so far. Crossing my fingers for another five+ hours :) Update 2 The recovery of /dev/sdd finished, with dmesg output: [44972.599552] md: md0: recovery done. [44972.682811] RAID conf printout: [44972.682815] --- level:6 rd:4 wd:4 [44972.682817] disk 0, o:1, dev:sdb [44972.682819] disk 1, o:1, dev:sdc [44972.682820] disk 2, o:1, dev:sdd [44972.682821] disk 3, o:1, dev:sde Attempting mount /dev/md0 reports: mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so And on dmesg: [44984.159908] EXT4-fs (md0): ext4_check_descriptors: Block bitmap for group 0 not in group (block 1318081259)! [44984.159912] EXT4-fs (md0): group descriptors corrupted! I'm not sure what do do now. Suggestions? Output of dumpe2fs /dev/md0: dumpe2fs 1.42.8 (20-Jun-2013) Filesystem volume name: Atlas Last mounted on: /mnt/atlas Filesystem UUID: e7bfb6a4-c907-4aa0-9b55-9528817bfd70 Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: user_xattr acl Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 244195328 Block count: 976756712 Reserved block count: 48837835 Free blocks: 92000180 Free inodes: 243414877 First block: 0 Block size: 4096 Fragment size: 4096 Reserved GDT blocks: 791 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8192 Inode blocks per group: 512 RAID stripe width: 2 Flex block group size: 16 Filesystem created: Thu May 24 07:22:41 2012 Last mount time: Sun May 25 23:44:38 2014 Last write time: Sun May 25 23:46:42 2014 Mount count: 341 Maximum mount count: -1 Last checked: Thu May 24 07:22:41 2012 Check interval: 0 (<none>) Lifetime writes: 4357 GB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: e177a374-0b90-4eaa-b78f-d734aae13051 Journal backup: inode blocks dumpe2fs: Corrupt extent header while reading journal super block

  Read the article

• Algorithms for pairing a rating system to an assignment queue

  - by blunders

  Attempting to research how to allow a group of people to effectively rank a set of objects (each group member will have contributed one object to the group), and then assign each member an object that's not their own based on: Their ratings of the objects, Their objects rating, and The object remaining to be assigned. Idea is to attempt to assign objects to people based on the groups rating of their contribution to the group relative to other member's contribution, the the personal preferences expressed via the ratings. Any suggestions for: Further research, Refining the statement of the problem/solution, or A solution.

  Read the article

• Raid superblock missing on single parition. Recovery needed!

  - by user171639

  Ok so I have a 2 TB raid 1 setup that has three partitions: sdc1: linux sdc2: swap sdc3: LVM for data However the LVM will no longer mount. So I thought that I would take the first drive, mount it in linux (ive done this b4), and reset the spare drive to copy the data. Normally I can mount a single drive for data recovery using: sudo su apt-get install mdadm lvm2 mdadm --assemble --scan modprobe dm-mod vgscan vgchange -ay c mount -o ro /dev/c/c /mnt Unfortunately, vgscan doesnot recognize the data partition. It appears as though the superblock on the first drive's data partition was erased while syncing with the second. So now I cannot mount that partition and the second drive is stuck in spare mode. Any ideas? Or a way to force mount the data partition just to copy the data? knoppix@Microknoppix:~$ sudo su root@Microknoppix:/home/knoppix# apt-get install mdadm lvm2 Reading package lists... Done Building dependency tree Reading state information... Done lvm2 is already the newest version. mdadm is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 551 not upgraded. root@Microknoppix:/home/knoppix# mdadm --assemble --scan mdadm: /dev/md/1 has been started with 1 drive (out of 2). mdadm: /dev/md/0 has been started with 1 drive (out of 2). root@Microknoppix:/home/knoppix# modprobe dm-mod root@Microknoppix:/home/knoppix# vgscan Reading all physical volumes. This may take a while... No volume groups found root@Microknoppix:/home/knoppix# cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[2] 4193268 blocks super 1.2 [2/1] [U_] md1 : active raid1 sdc2[2] 524276 blocks super 1.2 [2/1] [U_] unused devices: <none> root@Microknoppix:/home/knoppix# mdadm -v --assemble --auto=yes /dev/md2 /dev/sdc3 mdadm: looking for devices for /dev/md2 mdadm: no recogniseable superblock on /dev/sdc3 mdadm: /dev/sdc3 has no superblock - assembly aborted root@Microknoppix:/home/knoppix# dumpe2fs /dev/md0 | grep -i superblock dumpe2fs 1.42.4 (12-Jun-2012) Primary superblock at 0, Group descriptors at 1-1 Backup superblock at 32768, Group descriptors at 32769-32769 Backup superblock at 98304, Group descriptors at 98305-98305 Backup superblock at 163840, Group descriptors at 163841-163841 Backup superblock at 229376, Group descriptors at 229377-229377 Backup superblock at 294912, Group descriptors at 294913-294913 Backup superblock at 819200, Group descriptors at 819201-819201 Backup superblock at 884736, Group descriptors at 884737-884737 root@Microknoppix:/home/knoppix# Notes: I can read the super block from the spare drive. I was gonna try and restore the superblock from one of the backups, but i dont know how or if this would work. I also heard creating a new array (mdadm --create) using the same parameters will not delete the data on the drive but i didnt want to risk it. Recommendations?

  Read the article

• Help with mysql sum and group query and managing jquery graph results.

  - by Scarface

  Hey guys, I have a system I am trying to design that will retrieve information from a database, so that it can be plotted in a jquery graph. I need to retrieve the information and somehow put it in the necessary format (for example two coordinates var d = [[1269417600000, 10],[1269504000000, 15]];). My table that I am selecting from is a table that stores user votes with fields: points_id (1=vote up ,2=vote down), user_id, timestamp, and topic_id. What I need to do is select all the votes and somehow group them into respective days and then sum the difference between 1 votes and 2 votes for each day. I then need to somehow display the data in the appropriate plotting format shown earlier. For example April 1, 4 votes. The data needs to be separated by commas, except the last plot entry, so I am not sure how to approach that. I showed an example below of the kind of thing I need but it is not correct, echo "var d=["; $query=mysql_query("SELECT *, SUM(IF(points_id = \"1\", 1,0))-SUM(IF([points_id = \"2\", 1,0)) AS 'total' FROM points LEFT JOIN topic on topic.topic_id=points.topic_id WHERE topic.creator='$user' GROUP by timestamp HAVING certain time interval"); while ($row=mysql_fetch_assoc($query)){ $timestamp=$row['timestamp']; $votes=$row['total']; echo "[$timestamp,$vote],"; } echo "];";

  Read the article

• Is there a way to get number of connections in Signalr hub group?

  - by pajo

  Here is my problem, I want to track if user is online or offline and notify other clients about it. I'm using hubs and implemented both IConnected and IDisconnect interfaces. My idea was to send notification to all clients when hub detects connect or disconnect. By default when user refreshes page he will get new connection id and eventually previous connection will call disconnect notifying other clients user is offline even though he's actually online. I tired to use my own ConnectionIdFactory returning username for connection id but with multiple tabs opened at some point it will detect user connectionid disconnected and after that client side hub will try to unsuccessfully connect to the hub in endless loop wasting memory and cpu making browser almost unusable. I needed to fix it fast so I removed my factory and now I add every new connection to the group using username, so I can easily notify single user on all connections, but then I have problem of detecting if user is online or offline as I don't know how many active connection user is having. So I'm wondering is there a way to get number of connections in one group? Or if anybody has some better idea how to track when user goes offline? I'm using Signalr 0.4

  Read the article

• Correlate GROUP BY and LEFT JOIN on multiple criteria to show latest record?

  - by Sunbird

  In a simple stock management database, quantity of new stock is added and shipped until quantity reaches zero. Each stock movement is assigned a reference, only the latest reference is used. In the example provided, the latest references are never shown, the stock ID's 1,4 should have references charlie, foxtrot respectively, but instead show alpha, delta. How can a GROUP BY and LEFT JOIN on multiple criteria be correlated to show the latest record? http://sqlfiddle.com/#!2/6bf37/107 CREATE TABLE stock ( id tinyint PRIMARY KEY, quantity int, parent_id tinyint ); CREATE TABLE stock_reference ( id tinyint PRIMARY KEY, stock_id tinyint, stock_reference_type_id tinyint, reference varchar(50) ); CREATE TABLE stock_reference_type ( id tinyint PRIMARY KEY, name varchar(50) ); INSERT INTO stock VALUES (1, 10, 1), (2, -5, 1), (3, -5, 1), (4, 20, 4), (5, -10, 4), (6, -5, 4); INSERT INTO stock_reference VALUES (1, 1, 1, 'Alpha'), (2, 2, 1, 'Beta'), (3, 3, 1, 'Charlie'), (4, 4, 1, 'Delta'), (5, 5, 1, 'Echo'), (6, 6, 1, 'Foxtrot'); INSERT INTO stock_reference_type VALUES (1, 'Customer Reference'); SELECT stock.id, SUM(stock.quantity) as quantity, customer.reference FROM stock LEFT JOIN stock_reference AS customer ON stock.id = customer.stock_id AND stock_reference_type_id = 1 GROUP BY stock.parent_id

  Read the article

• Why aren't my MySQL Group By Hours vs Half Hours files Not displaying same data?

  - by stogdilla

  I need to be able to display data that I have in 15 minute increments in different display types. I have two queries that are giving me trouble. One shows data by half an hour, the other shows data by hour. The only issue is that the data totals change between queries. It's not counting the data that happens between the time frames, only AT the time frames. Ex: There are 5 things that happen at 7:15am. 2 that happen at 7:30am and 4 that show at 7:00am. The 15 minute view displays all of the data. The half hour view displays the data from 7:00am and from 7:30am but ignores the 7:15am. The hour display only shows the 7:00am data Here are my queries: $query="SELECT * FROM data WHERE startDate='$startDate' and queue='$queue' GROUP BY HOUR(start),floor(minute(start)/30)"; and $query="SELECT * FROM data WHERE startDate='$startDate' and queue='$queue' GROUP BY HOUR(start) "; How can I pull out the data in groups like I have but get all the data included? Is the issue the way the data is stored in the mysql table? Currently I have a column with dates (2010-03-29) and a column with times (00:00) Do I need to convert these into something else?

  Read the article

• Help with mysql sum and group query and managing results for jquery graph.

  - by Scarface

  I have a system I am trying to design that will retrieve information from a database, so that it can be plotted in a jquery graph. I need to retrieve the information and somehow put it in the necessary coordinates format (for example two coordinates var d = [[1269417600000, 10],[1269504000000, 15]];). My table that I am selecting from is a table that stores user votes with fields: points_id (1=vote up, 2=vote down), user_id, timestamp, topic_id What I need to do is select all the votes and somehow group them into respective days and then sum the difference between 1 votes and 2 votes for each day. I then need to somehow display the data in the appropriate plotting format shown earlier. For example April 1, 4 votes. The data needs to be separated by commas, except the last plot entry, so I am not sure how to approach that. I showed an example below of the kind of thing I need but it is not correct, echo "var d=["; $query=mysql_query( "SELECT *, SUM(IF(points_id = \"1\", 1,0))-SUM(IF([points_id = \"2\", 1,0)) AS 'total' FROM points LEFT JOIN topic ON topic.topic_id=points.topic_id WHERE topic.creator='$user' GROUP by timestamp HAVING certain time interval" ); while ($row=mysql_fetch_assoc($query)){ $timestamp=$row['timestamp']; $votes=$row['total']; echo "[$timestamp,$vote],"; } echo "];";

  Read the article

• How to add "missing" columns in a column group in reporting services?

  - by Gimly

  Hello, I'm trying to create a report that displays for each months of the year the quantity of goods sold. I have a query that returns the list of goods sold for each month, it looks something like this : SELECT Seller.FirstName, Seller.LastName, SellingHistory.Month, SUM(SellingHistory.QuantitySold) FROM SellingHistory JOIN Seller on SellingHistory.SellerId = Seller.SellerId WHERE SellingHistory.Year = @Year GOUP BY Seller.FirstName, Seller.LastName, SellingHistory.Month What I want to do is display a report that has a column for each months + a total column that will display for each Seller the quantity sold in the selected month. Seller Name | Jan | Feb | Mar | Apr | May | Jun | Jul | Aug | Sep | Oct | Nov | Dec | Total What I managed to do is using a matrix and a column group (group on Month) to display the columns for existing data, if I have data from January to March, it will display the 3 first columns and the total. What I would like to do is always display all the columns. I thought about making that by adding the missing months in the SQL request, but I find that a bit weird and I'm sure there must be some "cleanest" solution as this is something that must be quite frequent. Thanks. PS: I'm using SQL Server Express 2008

  Read the article

• How do i create a group of h:selectOneRadio in JSF?

  - by Nitesh Panchal

  Hello, I am trying to create a grooup of h:selectOneRadio but ui:repeat gives it different id for each row. This is my code :- <ui:repeat id="themes" value="#{RegisterBean.objBlogTemplateList}" var="item"> <p:graphicImage alt="#{item.templatePicName}" style="border: solid 5px white;width: 200px;height: 200px;" value="#{app:getCommonImagePath(item.templatePicName)}"/> <h:selectOneRadio rendered="false" value="#{RegisterBean.blogTemplateId}" layout="lineDirection" id = "rdTemplateId"> <f:selectItem itemLabel="#{item.templateName}" itemValue="#{item.templateId}"/> </h:selectOneRadio> </ui:repeat> Actually i want to create a single radio button with different selectItems in it which should be from the rows of my table in database. How do i do this?

  Read the article

• Iterate through all form fields within a specified DIV tag.

  - by user344255

  I need to be able to iterate through all the form fields within a specified DIV tag. Basically, any given DIV tag can have multiple form fields (which is easy enough to parse through), but it can also any number of tables or even additional DIV tags (adding additional levels of hierarchical layering). I've written a basic function that goes through each of the direct descendants of the parent node (in this case, the DIV tag) and it clears out its value. This part works fine. The problem is getting it to parse children when children (grandchildren) of their own. It winds up getting caught up in an infinite loop. In this case, I need be able to find all the form fields within DIV tag "panSomePanel", which will include some direct children (txtTextField1), but also some grandchildren who are within nested TABLE objects and/or nested DIV tags (radRadioButton, DESC_txtTextArea). Here is a sample DIV and its contents: <DIV id="panSomePanel"> <INPUT name="txtTextField1" type="text" id="txtTextField1" size="10"/><BR><BR> <TABLE id="tblRadioButtons" border="0"> <TR> <TD> <INPUT id="radRadioButton_0" type="radio" name="radRadioButton" value="1" /><LABEL for="radRadioButton_0">Value 1</LABEL> </TD> <TD> <INPUT id="radRadioButton_5" type="radio" name="radRadioButton" value="23" /><LABEL for="radRadioButton_5">Value 23</LABEL> </TD> </TR> <TR> <TD> <INPUT id="radRadioButton_1" type="radio" name="radRadioButton" value="2" /><LABEL for="radRadioButton_1">Value 2</LABEL> </TD> <TD> <INPUT id="radRadioButton_6" type="radio" name="radRadioButton" value="24" /><LABEL for="radRadioButton_6">Value 24</LABEL> </TD> </TR> <TR> <TD> <INPUT id="radRadioButton_2" type="radio" name="radRadioButton" value="3" /><LABEL for="radRadioButton_2">Value 3</LABEL> </TD> <TD> <INPUT id="radRadioButton_7" type="radio" name="radRadioButton" value="25" /><LABEL for="radRadioButton_7">Value 25</LABEL> </TD> </TR> <TR> <TD> <INPUT id="radRadioButton_3" type="radio" name="radRadioButton" value="21" /><LABEL for="radRadioButton_3">Value 21</LABEL> </TD> <TD> <INPUT id="radRadioButton_8" type="radio" name="radRadioButton" value="4" /><LABEL for="radRadioButton_8">Value 4</LABEL> </TD> </TR> <TR> <TD> <INPUT id="radRadioButton_4" type="radio" name="radRadioButton" value="22" /><LABEL for="radRadioButton_4">Value 22</LABEL> </TD> </TR> </TABLE> <DIV id="panAnotherPanel"><BR> <TABLE cellpadding="0" cellspacing="0" border="0" style="display:inline;vertical-align:top;"> <TR> <TD valign="top"> <TEXTAREA name="DESC:txtTextArea" rows="3" cols="48" id="DESC_txtTextArea"></TEXTAREA>&nbsp; </TD> <TD valign="top"><SPAN id="DESC_lblCharCount" style="font-size:8pt;"></SPAN> </TD> </TR> </TABLE> </DIV> </DIV> Here is the function I've written: function clearChildren(node) { var child; if (node.childNodes.length > 0) { child= node.firstChild; } while(child) { if (child.type == "text") { alert(child.id); child.value = ""; } else if (child.type == "checkbox") { child.checked = false; } else if (child.type == "radio") { alert(child.id); child.checked = false; } else if (child.type == "textarea") { child.innerText = ""; } //alert(child.childNodes.length); if (child.childNodes.length > 0) { var grandchild = child.firstChild; while (grandchild) { clearChildren(grandchild); } grandchild = grandchild.nextSibling; } child = child.nextSibling; } }

  Read the article

• CSS [custom?] attributes

  - by Michael

  radio[pane] { list-style-image: url("jar:resource:///chrome/classic.jar! /skin/classic/browser/preferences/Options.png"); } radio[pane="prefpane-appearance"] { -moz-image-region: rect(0px, 32px, 32px, 0px); } radio[pane="prefpane-appearance"]:hover, radio[pane="prefpane-appearance"][selected="true"] { -moz-image-region: rect(32px, 32px, 64px, 0px); } Can anyone explain a syntax of this css, particularly what is pane.. I couldn't find such attribute for radio element in context of XUL. So I guess it's some custom attribute? If it is, then how it is evolving through the lines, first declaration, then several assignments? It has also selected, which means can have multiple custom attributes? How can those attributes be used later?

  Read the article

• Need some resoultion. Javascript function not being called in click event in jquery.

  - by Shantanu Gupta

  I am trying to call my function named isUrgencyTypeValid from my javascript code but it is not working. Please check what is the problem in my code. Alert should get displayed which is not being displayed My javascript function is not being called. HTML Code <td colspan="2" align="center"><input id="btnSubmit" type="submit" value="submit" runat="server"/></td></tr> jQuery Call function $("#btnSubmit").bind("click",function(){ alert(); // this is running isUrgencyTypeValid(); }); javascript implemented function function isUrgencyTypeValid() { alert("asd"); var i=0; for(i=0;i<$("radio[name='urgencyType']").length;i++) { if($("radio[name='urgencyType']")[i].checked) { alert($("radio[name='urgencyType']")[i].value); return true; } return false; } More description about my form is here <form runat="server" name="myPage"> <table style="width: 100%;" cellpadding="5" cellspacing="5"> <caption> Computer Support / Service Request </caption> <tr><td>First Name</td> <td><input id="txtFirstName" type="text" value="First Name" runat="server"/><span class="error"></span></td></tr> <tr> <td>Last Name</td> <td><input id="txtLastName" type="text" value="Last Name" runat="server"/><span class="error"></span></td></tr> <tr> <td>Email Address</td> <td><input id="txtEmailAddress" type="text" value="Email Address" runat="server"/><span class="error"></span></td></tr> <tr> <td>Phone No</td> <td><input id="txtPhoneNo" type="text" value="Phone No" runat="server" /><span class="error"></span></td></tr> <tr> <td>Do you have text messaging</td> <td> <span>Yes</span><input id="rdoYes" value="Yes" type="radio" runat="server"/> <span>No</span><input id="rdoNo" value="No" type="radio" runat="server"/><span class="error"></span> </td></tr> <tr> <td>Description of request*: </td> <td><textarea id="txtDescription" cols="50" rows="10" runat="server"></textarea><span class="error"></span><span id="lengthCount"></span></td></tr> <tr> <td>Urgency of this support request:</td> <td> <input id="rdoAnyTime" name="urgencyType" value="Anytime" type="radio" runat="server"/><span>Anytime</span><br /> <input id="rdoCplDays" name="urgencyType" value="In the next couple of days" type="radio" runat="server"/><span>In the next couple of days</span><br /> <input id="rdoToday" name="urgencyType" value="Today" type="radio" runat="server"/><span>Today</span><br /> <input id="rdoUrgent" name="urgencyType" value="This is extremely urgent...I cannot wait!" type="radio" runat="server"/><span>This is extremely urgent...I cannot wait!</span><br /> <input id="rdoTalkSometime" name="urgencyType" value="Please contact me and we'll talk about it" type="radio" runat="server"/><span>Please contact me and we'll talk about it</span><br /><span class="error"></span> </td></tr> <tr> <td colspan="2" align="center">Captcha To Be implemented.</td></tr> <tr> <td></td> <td><input id="chkRequestCopy" type="checkbox" runat="server"/>Please send me a copy of this service request</td></tr> <tr> <td colspan="2" align="center"><input id="btnSubmit" type="submit" value="submit" runat="server"/></td></tr> </table> </form>

  Read the article

• Basic question about request queues in IIS / ASP.Net

  - by larryq

  I have an ASP.Net application running under IIS 6. A simple page has two radio buttons and a submit button. If I select radio button "A" and submit the page, a lengthy PDF file is generated, which takes about a minute to build. If I select radio button "B", a small PDF is generated. (In both cases the PDF is written out to the Response object and it opens in my browser.) If I select radio button "A" and submit, then hit the red X in my browser to stop the current request, then select radio button "B" and resubmit, the page still takes a long time to process my request. No doubt my first request is still being processed on the server, but I was wondering how IIS and/or ASP.Net are queuing my requests so that fair server use is guaranteed among all users. Am I roughly correct in assuming something like this happens, and if so, how is it done?

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >