Search Results

Search found 4141 results on 166 pages for 'router'.

Page 85/166 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

• adding a route entry to linux routing table

  - by netg

  hi, I have two systems with ip address say 64.103.56.1(A)(Dev name -wlan0) and 64.103.225.18(B),now what i want is , everytime I ping B from my system A, it has to be routed via a router say with address 10.0.0.251(C)(I want this to be my next hop to reach B) , but this router is on a different subnetwork than the two systems.How do I do this? /* Things I tried: I used 'route add -host B gw C wlan0', and got an error saying " no such process exist or no such device found". Tried ping C and traceroute and found the gw addr at my side is some 63.103.236.3(D), so added another entry route add -host C gw D wlan0, I was able to do this without any error! */

  Read the article

• Apple Airport Extreme Wireless Card M8881 Connectivity Issue

  - by Carlosfocker

  I bought a Apple Airport Extreme Wireless Card M8881 with the antenna for my old Power Mac G5 1.6 Ghz. The computer is running OS X 10.4. The card works and I can connect to my dlink 802.11g wireless router using WPA2/AES encryption. The problem is that the connection has intermittent connectivity issues. When the issue occurs the signal bars for the connection drop to one or two bars and the performance of the connection suffers greatly. The computer isn't far from the wireless router. I have a laptop at the desk where the mac is and it does not have any issues. I'm not sure what it might be? Updated drivers? Firmware? Let me know if I forgot any important information.

  Read the article

• A design for watching IPTV anywhere in the house?

  - by Carlos

  I'm currently getting TV and internet via IP to my house. The service comes into an ISP-supplied Router (ST585) which is in turn connected to an IPTV box. I need to replace the router, as it's port forwarding seems to be broken, so I was thinking of getting a box with an IGMP proxy. I once mistakenly got a non-IGMP box, with the result that the internet worked, but the IPTV didn't. The trouble is, I have no idea how to set up the IPTV part of the installation. I do have a copy of the ST585 configuration, but it doesn't look anything like the Cisco stuff that I learned about at CCNA. What are the steps necessary to reproduce the IGMP setup? I was thinking of WireSharking the communications on the network, but I suppose I'd need a hub for that? As a bonus, since the packets are coming in with the TV signal, is it possible to mess with the IGMP setup so I can watch TV anywhere in the house?

  Read the article

• A design for watching IPTV anywhere in the house?

  - by Carlos

  I'm currently getting TV and internet via IP to my house. The service comes into an ISP-supplied Router (ST585) which is in turn connected to an IPTV box. I need to replace the router, as it's port forwarding seems to be broken, so I was thinking of getting a box with an IGMP proxy. I once mistakenly got a non-IGMP box, with the result that the internet worked, but the IPTV didn't. The trouble is, I have no idea how to set up the IPTV part of the installation. I do have a copy of the ST585 configuration, but it doesn't look anything like the Cisco stuff that I learned about at CCNA. What are the steps necessary to reproduce the IGMP setup? I was thinking of WireSharking the communications on the network, but I suppose I'd need a hub for that? As a bonus, since the packets are coming in with the TV signal, is it possible to mess with the IGMP setup so I can watch TV anywhere in the house?

  Read the article

• How do ISPs/Colocation Facilities limit bandwidth for Ethernet Drops?

  - by Kyle Brandt

  I have switch providers and have run into some problems with bandwidth limitations. I have more bandwidth then before, but there are performance issues. The router is connected to a 100mBit port, but they limit it to arbitrary settings (in software I imagine). It seems when I go above the limit, the provider starts to drop packets beyond the limit (This is what they said they do as well). Is it possible the previous provider did something like queuing packets above the this limit before dropping them? Is anyone aware of not only what can be done, but what is typical? Also, is there anything I can do on my Cisco router to help this situation? It would seem I am pretty helpless if the packets are dropped before they reach my interface (The traffic that is high is inbound to my network).

  Read the article

• How to query a DHCP server to get the local DNS servers

  - by Dan Berlyoung

  I have a ClarkConnect (CentOS based) box running as my home router on a RR connection. I had the DNS servers set up to use Google's DNS server. I want to change them back to the local DNS servers but I can't find an obvious/easy way to get those address short of a) reconfiguring the router's network to DHCP them (would rather not interrupt everyone) or b) calling their tech support (kill me now!). Is there a command line tool/command I can use to query the DHCP server on the external NIC to see what DNS servers it would set me up with w/o munging my existing setup?

  Read the article

• dd-wrt switch for PfSense

  - by Kmao

  I currently have eth2 on my pfsense set up, and configured as 192.168.1.1, it has dhcp setup with allocation being 192.168.1.10 - 192.168.1.245. On my dd-wrt box, i disabled the WAN, and set it to act as a port for the switch. I disabled dhcp, dnsmasq, spi firewall, Wlan0 and set a static IP for the router being 192.168.1.10 Pfsense is plugged into lan0 and pc plugged into lan1 (wan port is empty) I have followed a few different guides, but i can't seem to get my router to act as a switch. Anyone have success using DD-WRT as a switch while using pfsense as your dhcp/dns/gateway. Any advice would help :)

  Read the article

• how do I set up a virtual host (it's not working, and I've done everything right)

  - by piratepartypumpkin

  My router redirects port 80 to port 8080. My router works fine and my domain name is routed properly. This is my virtual hosts file: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /home/admins/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> I can access my website by entering "mywebsite.com:8080" but I cannot access it by entering "mywebsite.com" For further information, this is a part of my httpd.conf: Listen 8080 Servername localhost:8080 DocumentRoot "/home/admins/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/home/admins/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• diagnostic software for wifi adapter

  - by Nathan Fellman

  I'm having trouble with my wifi connection. Is there any software out there that can help me determine if the problem is in the drivers or in the hardware? Regretfully, I'm working on Vista Edit: The problem I'm having is that the Vista reports that the wireless radio is connected, shows an IP and all, the router also shows that the computer is connected, but there's no connectivity. I can't logon to the router, and I can't even ping it. When I ping it I get the response: General Failure I have tried connecting with and without various wireless security protocols. I have tried disabling the wireless adapter and re-enabling it from the Device Manager I have tried updating the driver None of this has helped. When I connect via Ethernet (with a cable, that is), everything works fine. Edit: I'm not using any firewall on the computer, that I'm aware of. The IP address for the WIFI adapter is similar to the one for the LAN adapter. They differ by one.

  Read the article

• What are the advantages of OSPF vs nexthop self with iBGP?

  - by Matt Hamilton

  Assuming I have a fairly small network internally, but I have 4 routers each connected out to a different network. The routers are all sat next to each other connected via a switch. Each router uses BGP to speak to the outside networks. There is an iBGP mesh for each router to exchange the routes internally it knows about from each external network. The usual setup is to use OSPF to distribute the connected routes, as the routes via iBGP will still have the next hop set to their original value. What is the advantage of using OSPF in this scenario versus simply using 'set nexthop self' on the routes?

  Read the article

• Configuring Nagios BGP plugin on Ubuntu

  - by user141610

  I am trying to configure nagios check_bgp_neighbors plug-in on Ubuntu and followed README file of check_bgp_neighbors plug-in. I have made following changes: define command{ command_name check_bgp_all command_line $USER1$/check_bgp_neighbors -H $HOSTADDRESS$ -C $USER3$ -n $ARG1$ -n $ARG2$ } to define command{ command_name check_bgp_all command_line /usr/local/nagios/libexec/check_bgp_neighbors.sh -H xx.xx.xx.49 -C xx.xx.xx.50 And define service{ use server-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!10.0.0.1!172.16.0.2 } to define service{ use generic-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!xx.xx.xx.50 } xx.xx.xx.49 is the IP of the host router and xx.xx.xx.50 is the IP of eBGP neighbour. After that it shows critical status. I know my command is not correct but cannot detect the problem. I learned that in this plug-in user-name and password of the host router are required but don't know how and where to provide it. Nagios log does not show any error message. Status information: Failed: status:0 prefixes:0 sent:0 received:0

  Read the article

• Shielded ethernet cable and ethernet sockets earthing how to?

  - by ageis23

  Hi I'm going to install 5 Ethernet sockets in my house using cat5e shielded cable. I decided to use this because the sockets will be on the second floor and the most practical way up is within a trunk along with some mains wiring. The cable will be terminated at the router and at the Ethernet faceplate. What can I use to earth then? The faceplate/router are both plastic hence no earth wire needed. I can't use the earth wire within the main socket can I? I figured it will be very very dangerous. I don't want to be connecting to the earth block on the mains either since I totally incompetent when it comes to mains electricity.

  Read the article

• How to route all traffic over site to site VPN tunnel?

  - by Hutch

  I have a site to site VPN configured between our main site (Site A) and a remote site (Site B). Site A is 10.60.0.0/16 Site B is 192.168.99.0/24 The firewall in Site B is a Juniper SSG running ScreenOS 6.3 and I'm using a route based VPN. The tunnel works perfectly in that from Site A you can reach 192.168.99.0 via the tunnel, and from Site B you can reach 10.60.0.0 via the tunnel. However, we want it so that if you're in Site B and want the Internet it goes via the firewall at Site A, and right now on the Juniper 0.0.0.0 has the ISP router as next hop. My understanding is that on the Juniper, I can set a route for the /32 public IP at our main site that the VPN tunnel connects to to the ISP router via ethernet0/0 (the SSG's external interface), and then modify the 0.0.0.0 route to use our main site firewall via tunnel.1 (the VPN tunnel). Not sure I've explained that so well but is my understanding correct? Thanks

  Read the article

• Jumbo Frames on DIR-655

  - by Spookyone

  Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Windows 7 PPTP VPN problem

  - by Marco Martins

  Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

  Read the article

• No Internet for Created VLan on Cisco CE500

  - by Jennifer

  I'm new here and also with networking but i can't set internet conection for some vlan created. I have a Cisco CE500 switch and created 4 vlans define by the roles in the switch. Vlan 2: Servers (role) (port 3-4) Vlan 3: Desktop (role) (port 5-8) Vlan 4: Guest (role) (port 9-12) Vlan 1 is default, Connect to the ADSL Modem/Router Port 2 assign to the Router Role (vlan 1) The switch is connected on port2 the ADSL Modem (DHCP) 192.168.2.254 The goal is: All Vlan should have internet connection. Vlan 2 and 3 should see each other but not Vlan 4 I can enter the switch CLI but dont know which command to enter. Thanks 4 ur time and replies Jennifer

  Read the article

• How to connect to my US network overseas via VPN?

  - by GiH

  I purchased an Apple TV for my parents and I have a netflix account. My parents live overseas, and I was wondering if they could use my account to get it to work. I read that it won't work unless you use proxies or a VPN, so I was wondering if its possible for me to setup a VPN to my network in the US instead of paying a service like StrongVPN? Setup: Router in US - Airport Extreme Router abroad - D-link (not sure of model) I know that the AppleTV doesn't have a built-in VPN client, maybe eventually when its jailbroken there will be an app, but as of now I'll have to use the routers right? Any other ideas are welcome as well!

  Read the article

• Connect macbook to my LAN through a VPN - best solution?

  - by LewisMc

  So I have a LAN connected via a ADSL/PPPoA, this is using a bog-standard DLink router supplied by my ISP (talktalk UK). I have a NAS within the LAN that is running FreeNAS and I want to be able to connect to it when I'm out and about. It's running an atom so it's quite low on juice consumption but I don't want to have it on all day and night so I've been waking it via a magic packet and booting it down from the web admin when I need it. So I want to connect to the LAN, I presume via a VPN, to be able to send a magic packet. But what is the best method to accomplish this, or is there an easier way? I've been looking at the cisco 857 integrated router and the Netgear prosafe 318(behind modem) but not sure If I'm on the right track with what I want to achieve as I've not much experience or knowledge with VPN's or networking (software engineering student). I have tried port forwarding but to no avail, either with magic packets or even connecting outside the LAN via DYNDNS. Thanks,

  Read the article

• Sharing internet connection with WDS

  - by cornjuliox

  Is it possible to share an internet connection through WDS? I'm on the very edge of a wireless network, the spot that I'm in maintains a stable 22% according to XP with the help of a parabolic reflector crafted from a cheap pie tin. I was thinking I could grab another wireless router, use WDS to bridge the this router with the other one and share the 'net connection through it thus giving me a little bit more freedom but when I tried it it didn't work. WDS looks like it bridged the networks just fine, but I couldn't access anything on the internet. Do I need to do anything special or is this just not possible?

  Read the article

• Windows 7 wifi reports "no network access" and "no internet access" but connects in fedora

  - by rick2047

  I am running windows 7 home basic (64bit) on a Acer 5742G laptop with Atheos wifi adapter in it. Yesterday, I hiberneted my computer as I always do and up untill then the wifi was working fine. When I booted my computer up again today I started having a strange problem: It detects my wifi but after connecting to it, it keeps on oscillating between states of no network access and no internet access. I can't connect to anything (the internet or my router). I tried to reset my internet protocol stack using this fixit file. I also tried to uninstall and reinstall my network driver. Neither helped. I am using the same laptop's fedora installation right now and the wifi is working perfectly fine. Please help. Edit To add additional details, I have Microsoft Security essentials as my antivirus software and I haven't messed with the firewall or the router configurations.

  Read the article

• What is a 'firewall sniffer'?

  - by Craig Johnston

  What is a 'firewall sniffer'? How do they compromise the security of: Windows firewall Router firewall NAT firewall

  Read the article

• Why ping another inet machine from MacBook get netgate's ip address?

  - by Xinwang

  I have three machine in my home network connected by a wireless router. One is server installed linux at 192.168.1.1, another is Thinkpad with MS Windows XP at 192.168.1.2, last one is MacBook Pro with Mac OS X 10.6.3 at 192.168.1.3. When I ping the Linux Server from Thinkpad (MS Windows XP) I can get the correct ip address, but when I ping it from Mac I get the global address of my router, like 61.135.181.175. Could you tell me why this happen? And how do I get same ping result on Mac and Windows. Thanks

  Read the article

• Remote desktop to multiple windows machines on a LAN with dynamic IP

  - by kevyn

  Is it possible to use remote desktop to connect to multiple computers inside a network that has a dynamic IP address? I use a netgear WPN824 router which has dyndns onboard - but I currently use No-IP to control a single computer that I use most frequently. Every so often I need to get onto a couple of other computers in the network, but don't know how to go about this without logging onto one computer, and then starting another RDC session from that machine. What I would like to be able to do is connect to my router, and be able to see a list of connected devices, and then choose which to remote desktop onto. - I appreciate this probably is not be possible, but any other suggestions are welcome!

  Read the article

• setup advanced filtering and access restrictions on dd-wrt using iptables

  - by Nova deViator

  I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

  Read the article

• FTP error when doing file transfer

  - by Ernie

  I'm running vsftpd version 3.0.2 over FTPeS, and I'm having a bit of trouble with file transfers. It seems to work fine when I'm on the LAN, but not from an external IP address. I have the control port and data ports open on my server's software firewall and my router's firewall. When I'm using the service from an external IP address, it seems like sometimes a file transfer will complete, but it times out and I always get the client error: "426 Failure writing network stream". I've tried several clients. I'm thinking there is some sort of data sabotage either at the router or some server policy; maybe because I'm using passive ftp? Suggestions?

  Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >