Search Results

Search found 5180 results on 208 pages for 'outside'.

Page 86/208 | < Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >

• What hardware makes a good MongoDB Server ? Where to get it ?

  - by João Pinto Jerónimo

  Suppose you're on dell.com right now and you're buying a server to run your MongoDB database for your small startup. You will have to handle literally tens of thousands of writes and reads per minute (but small objects). Would you go for 2 processors ? Invest more on RAM ? I've heard (correct me if I'm wrong) MongoDB handles the most it can on the RAM and then flushes everything to the disk, in that case I should invest on a CPU with a large L2 cache, probably 40GB of RAM and a solid state drive.. right ? Would I be better off with a high end (~$11,309, 2 expensive processors, 96GB of RAM) server or 2x(~$6,419, 2 expensive processors, 12GB of RAM) servers ? Is Dell ok or do you have better sugestions ? (I'm outside the US, on Portugal)

  Read the article

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• How to rename everything matching a certain string in a folder

  - by lostiniceland

  Hello Everyone I am running Linux and I have some basic console knowledge but my current problem is quite difficult and I dont know how to achieve this. I want/need to rename everything within a folder that matches a given string. By everything I mean folders/files content within a file content in hidden files Basically I want to refactor a Java-project. Sure, I could use Eclipse to handle the replacing, but this leaves out the folders or resources outside of my workspace. I was thinking of a script that could do the job for me but this seems rather tricky. For instance when it comes to folder-/file-rename I want to replace only the part of the name that matches my string, the rest should remain untouched. Maybe someone already has something like this in his/her script-collection :-) Thanks in advance Marc

  Read the article

• Qmail & Open Relay on local domains

  - by Jonathan

  Hello. I have a dedicated server on 1&1 and I manage it with Plesk. The problem is that if I try to send a mail outside the server, I must to authenticate with the email and the password, but if I send an email to a address inside of my server I don't need neither email or password. This is a problem because the spammers are sending mails without any problem to the server accounts. We are receiving about 900 - 1200 emails everyday! What can I do? I use qmail on CentOS Thanks

  Read the article

• SonicWall HA "gotchas"?

  - by Mark Henderson

  We're looking to move away from PFSense and CARP to a pair of SonicWall NSA 24001 configured in Active/Passive for High Availability. I've never dealt with SonicWall before, so is there anything I should know that their sales guy won't tell me? I'm aware that they had an issue with a lot of their devices shutting down connectivity because of a licensing fault, and they have an overtly complex management GUI (on the older devices at least), but are there any other big "gotchas" that I need to be aware of before committing a not insubstantial amount of money towards these devices? 1If you're outside the US, the SonicWall global sites suck balls. Use the US site for all your product research, and then use your local site when you're after local information.

  Read the article

• eclipse IDE won't start in ubuntu 10.04 64bit with sun-java

  - by aeischeid

  i get this error when I try to run from CLI ** (Eclipse:2318): CRITICAL **: menu_proxy_module_load: assertion `dbusproxy != NULL' failed # A fatal error has been detected by the Java Runtime Environment: # SIGSEGV (0xb) at pc=0x00007f34511a4e74, pid=2318, tid=139863603410704 # JRE version: 6.0_18-b18 Java VM: OpenJDK 64-Bit Server VM (14.0-b16 mixed mode linux-amd64 ) Derivative: IcedTea6 1.8 Distribution: Ubuntu lucid (development branch), package 6b18-1.8-0ubuntu1 Problematic frame: C [libglib-2.0.so.0+0x41e74] g_main_context_prepare+0x164 # An error report file with more information is saved as: /home/aaron/opt/eclipse/hs_err_pid2318.log # If you would like to submit a bug report, please include instructions how to reproduce the bug and visit: https://bugs.launchpad.net/ubuntu/+source/openjdk-6/ The crash happened outside the Java Virtual Machine in native code. See problematic frame for where to report the bug. # I have sun-java installed and set in my PATH: ~: echo $JAVA_HOME /usr/lib/jvm/java-6-sun/

  Read the article

• how to restrict wampserver access to certain ip addresses

  - by user28233

  What do I need to do in order to restrict the access to my wamp server to certain ip addresses. Just imagine that the my ip address is the ip address that I only want to have access I tried to edit the .htaccess # This folder does not require access over HTTP # (the following directive denies access by default) Order allow,deny Allow from 112.203.229.44 and the phpmyadmin.conf: Alias /phpmyadmin "E:/wamp/apps/phpmyadmin3.2.0.1/" # to give access to phpmyadmin from outside # replace the lines # # Order Deny,Allow # Deny from all # Allow from my ip address # # by # # Order Allow,Deny # Allow from my ip address # <Directory "E:/wamp/apps/phpmyadmin3.2.0.1/"> Options Indexes FollowSymLinks MultiViews AllowOverride all Order Deny,Allow Deny from all Allow from my ip address </Directory>

  Read the article

• How to rename everything matching a certain string in a folder

  - by lostiniceland

  Hello Everyone I am running Linux and I have some basic console knowledge but my current problem is quite difficult and I dont know how to achieve this. I want/need to rename everything within a folder that matches a given string. By everything I mean folders/files content within a file content in hidden files Basically I want to refactor a Java-project. Sure, I could use Eclipse to handle the replacing, but this leaves out the folders or resources outside of my workspace. I was thinking of a script that could do the job for me but this seems rather tricky. For instance when it comes to folder-/file-rename I want to replace only the part of the name that matches my string, the rest should remain untouched. Maybe someone already has something like this in his/her script-collection :-) Thanks in advance Marc

  Read the article

• Small business VPN solution

  - by Crash893

  I've been looking for a while but I'd like to to implement a vpn solution for anywhere from 1-5 employees at a time (possibly 10 in a year or so) edit: Basically I would like outside users to fire up a client or open a web page and be able to access things inside the company network (share drives / printers/ webapps /etc) I've looked at Astaro Gateway but im not sure if that's the right tool for the job. I know "best" is a subjective term so i would like to break it into to different suggestions 1) what is the cheapest solution given the criteria above 2) what solution will result in the least amount of headaches from the point of view of maintenance and learning curve.

  Read the article

• IE 8 doesn't appear to clear cache on demand. Is anyone else seeing this?

  - by Steve

  I have a client that uploads updated pdf files to her Concrete5 CMS, through the file manager, replacing the old file with the same name. She then does a cms "clear cache" and exits as she should. Then, in testing, she finds that the old file still comes up when clicking on the link. On further review, the cms file manager version tracking shows that the file has been updated, and, for me, the new file comes up, as it should, when clicking the link. My client hase also refreshed her browser cache and still, she only gets the old file when clicking on the link. She says that, while she can't seem to force an immediate cache update, overnight it appears to update. My client is also part of a large company-wide lan and intranet. Is it possible that there is a cache function placed outside of her local browser and cms cache that is not updating?

  Read the article

• Server 2008 Task Scheduler and a CMD file

  - by Mark Smith

  Task Scheduler - I have a .cmd file I'm trying to execute on a regular basis through Task Scheduler. I've set the task so that it points to the cmd file. I want the task to execute even when no one is logged in. I've set the credentials associated with the task to the local service account. When I execute the task, nothing happens. The Last Run Result shows 0x1, this means it didn't execute properly. When I run the file from a command prompt it executes just fine. Any help out there would be appreciated. I would post the code but it has sensitive information in it and I'm not allowed to let the code outside. Thanks

  Read the article

• pinx 501 with print server - 10 licenses

  - by ra170

  I have pix 501 with only 10 licenses. I'm already approaching this limit, running 2 computers at home, 2 laptops, PS3, iphones, 2 web cams..not everthing is on all the time, but it's possible as I'm looking into adding a print server, so that I can print from anywhere in the house. So my question is, will the print server count as a connection towards the license? I think it will need default gateway, which in this case will be my pix 501. I've seen somewhere on some othee board saying, don't set default gateway in the print server to pix 501, but then how would that work? is there a work around? I don't need to print from VPN or from outside, just inside..

  Read the article

• What's required to enable communication between two IP ranges located behind one switch?

  - by Eric3

  Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

  Read the article

• Configure IIS 6 to deny access to specific file based upon IP address

  - by victorferreira

  Hello guys, We are using IIS 6 as our webserver. And we need to deny the access for one specif file, placed in only one specific URL, to everybody OUTSIDE the local network. In other words, if somebody is trying to access that filme/page from their own computer at home, using the internet, they must not succeed. But, if the same person try to do that at the same network of the web server, its ok. I am not sure about that, but Apache uses ORDER DENY,ALLOW. You specify the URL, allow or deny to all or to a range of IP. Any suggestions? Thanks!

  Read the article

• Advice for migrating email server

  - by Chris Adams

  Hi there, I'm planning to migrate a Zimbra server with about 200gb of data from a server hosted in an office into a datacentre, to increase uptime (we've had a couple of outages when our network here started flaking out, and we have people in other countries relying on this server too). However, I'm not sure how best to migrate the data into the data centre without rendering the connection unusable during office hours, because there's far too much to send in over night over the two meg upstream connection we have here. I'm familiar with using tools like nice to stop a long running process degrading machine performance - is there a simple way to throttle a connection between office hours, so the long running transfer doesn't block the pipe, but then opens up outside of office hours to make the most of the bandwidth? I'm aware the alternative here is to simply mail a hard drive to the data centre, but I'd like to avoid doing that if I could. We're using Centos Linux for our servers, in the office and the datacentre, so extra points for an open source linux answer.

  Read the article

• Tool for purging unneeded backups

  - by Dana the Sane

  I'm in the common situation where the one of the linux servers I use for storing backups is filling up. I'm wondering what tools are available for doing this. Ideally, what I would like is something that keeps nightlies for the previous month, weeklies for the 2nd to 5th preceding months and retains monthlies (well, every 3rd week) for an indefinite period. Everything that falls outside of that would be deleted after the backups are run. I could write a script to do this, but I feel like there must be a standard tool for this task.

  Read the article

• Open ports for Apache Tomcat-7.0.32 on Linux Mandriva

  - by ivanov-void

  I installed Apache Tomcat-7.0.32 on Linux Mandriva and I want to make it accessible. for this I need to open ports in iptables. I added the following rules- iptables -A INPUT -p tcp -m tcp --dport 8081 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8010 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8444 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8006 --syn -j ACCEPT then save and restart iptables - /etc/init.d/iptables save /etc/init.d/iptables restart verify, that ports is open - netstat -tulpn | less I am running command - netstat-ntpl | grep java and see - When I disable the firewall, I see the start page of the server on request - http://server_ip:8081/ When enable - server not accessible from outside. In what may be the cause? I would be most grateful for the information! Thank you!

  Read the article

• Configure IIS 6 to deny access to specific file based upon IP address

  - by victorferreira

  Hello guys, We are using IIS 6 as our webserver. And we need to deny the access for one specif file, placed in only one specific URL, to everybody OUTSIDE the local network. In other words, if somebody is trying to access that filme/page from their own computer at home, using the internet, they must not succeed. But, if the same person try to do that at the same network of the web server, its ok. I am not sure about that, but Apache uses ORDER DENY,ALLOW. You specify the URL, allow or deny to all or to a range of IP. Any suggestions? Thanks!

  Read the article

• HP Ambient Light Sensor Adjustment

  - by Robin Day

  I have an HP nc4400 running Windows 7 64 bit. If I have the ambient light sensor enabled, it works well, but, its slightly too dim. I can turn off the light sensor and turn up the brightness manually and its more than bright enough. When I go to the brightness settings in Windows I can make the screen dimmer with the ambient light sensor enabled but cannot make it as bright as if it is disabled. So my question is, is it possible to keep the light sensor enabled but configure it so that the screen is brighter for given "ambient light". At the moment I have to turn it off whenever I'm in the office or outside in sunlight as I need the screen as bright as possible and it seems no matter how light it is, it never goes to full brightness when it's enabled.

  Read the article

• using nmap to guess remote OS and probe service details on a single port only

  - by WoJ

  I am looking at scanning with nmap a large network in order to identify the OS of devices (-O--osscan-limit) probe for details of a service on a single port (I would have used -sV for all open ports) The problem is that -sV will probe all the ports (which I do not want to do for performance reasons) and I cannot use -p to limit the ports to the one I am interested in as this impacts the OS fingerprinting. I could not find anything in the manual to limit the service probing. Thank you for any ideas (including other approaches outside of nmap, though I would prefer to stick to nmap)

  Read the article

• SharePoint Server 2007 and HTML Forms - How to control access rights

  - by Anarkie

  I'm working with Hosted SharePoint 2007 with Forms Server. I need to allow client access to submit HTML forms designed in Infopath. Problem is, I need to make sure the clients don't see the library. There is sensitive data that will be on these forms. I also need to have a repeated library that is based on the Internal Admin records and requirements. Outside of making a seperate library per customer, does anyone have any suggestions? My Goal: 1: Customers enter their requests through a link or provided page 2: Internally address the requests and perform required arrangements, add billing and payment fields 3: Have SharePoint metrics, reports, etc... based on the provided intormation and status. Thanks in Advance!!

  Read the article

• Unable to reach files in subfolder with domain name in path in IIS 5.

  - by Chuck Conway

  In IIS 5 files in the url: http://acme.com/_cache/cache-www.acme.com/v3.css are not accessible. All files below "cache-www.acme.com" are unreachable. I've verified that the files exists. Permissions are not a problem. I've assigned "Everyone" to the files and give "Everyone" full rights. What I have determined is in IIS 5 if there is a domain in the folder path, IIS 5 gets confused... Other javascript files outside the directory comedown fine... Any thoughts?

  Read the article

• how to design network for connectivity between private and corporate LANs?

  - by maruti

  there is a bunch of servers connected to shared storage in a private LAN (10.x.x.x). this privateLAN is managed by a windows server (DHCP, DNS and directory services) these hosts need to be from outside of the datacenter Eg. Remote desktop. can the NIC2 on each of the hosts be connected to the other public LAN (compromising speed or security? what are improtant considerations: additional hardware? like switches? routing&DNS software? currently available hardware : Dell Powerconnect 6224 switch .... planning this for storage network. software: windows 2003 server for DHCP, DNS, A/D ? would it be more flexible to use Linux distributions like IPCOP, Untangle etc? all that I am looking for is good isolation between private and other networks, avoid DHCP, DNS, AD clashes.

  Read the article

• Portable and Secure Document Repository

  - by Sivakanesh

  I'm trying to find a document manager/repository (WinXP) that can be used from a USB disk. I would like a tool that will allow you to add all documents into a single repository (or a secure file system). Ideally you would login to this portable application to add or retrieve a document and document shouldn't be accessible outside of the application. I have found an application called Benubird Pro (app is portable) that allows you to add files to a single repository, but downsides are that it is not secure and the repository is always stored on the PC and not on the USB disk. Are you able to recommend any other applications? Thanks

  Read the article

• WCF Endpoints & Binding Configuration Issues

  - by CodeAbundance

  I am running into a very strange issue here folks. For simplicity I created a project for the sole purpose of testing the issue outside the framework of a larger application and still encountered what is either a bug in WCF within Visual Studio 2010 or something related to my WCF newbie skill set : ) Here is the issue: I have a WCF endpoint I created running inside of an MVC3 project called "SimpleMethod". The method runs inside of a .svc file on the root of the application and it returns a bool. Using the "WCF Service Configuration Editor" I have added the endpoint to my Web.Config along with a called "LargeImageBinding". Here is the service: [OperationContract] public bool SimpleMethod() { return true; } And the Web.Config generated by the Config Tool: <system.serviceModel> <bindings> <wsHttpBinding> <binding name="LargeImageBinding" closeTimeout="00:10:00" /> </wsHttpBinding> </bindings> <services> <service name="WCFEndpoints.ServiceTestOne"> <endpoint address="/ServiceTestOne.svc" binding="wsHttpBinding" bindingConfiguration="LargeImageBinding" contract="WCFEndpoints.IServiceTestOne" /> </service> </services> <behaviors> <serviceBehaviors> <behavior name=""> <serviceMetadata httpGetEnabled="true" /> <serviceDebug includeExceptionDetailInFaults="false" /> </behavior> </serviceBehaviors> </behaviors> <serviceHostingEnvironment multipleSiteBindingsEnabled="true" /> The service renders fine and you can see the endpoint when you navigate to: http://localhost:57364/ServiceTestOne.svc - Now the issue occurs when I create a separate project to consume the service. I add a service reference to a running instance of the above project, point it to: http://localhost:57364/ServiceTestOne.svc Here is the weird part. The service automatically generates just fine but In the Web.Config the endpoint that is generated looks like this: <client> <endpoint address="http://localhost:57364/ServiceTestOne.svc/ServiceTestOne.svc" binding="wsHttpBinding" bindingConfiguration="WSHttpBinding_IServiceTestOne" contract="ServiceTestOne.IServiceTestOne" name="WSHttpBinding_IServiceTestOne"> As you can see it lists the "ServiceTestOne.svc" portion of the address twice! When I make a call to the the service I get the following error: The remote server returned an error: (404) Not Found. I tried removing the extra "/ServiceTestOne.svc" at the end of the endpoint address in the above config, and I get the same exact error. Now what DOES work is if I go back to the WCF application and remove the custom endpoint and binding references in the Web.Config (everything in the "services" and "bindings" tags) then go back to the consumer application, update the reference to the service and make the call to SimpleMethod()....BOOM works like a charm and I get back a bool set to true. The thing is, I need to make custom binding configurations in order to allow for access to the service outside of the defaults, and from what I can tell, any attempt to create custom bindings makes the endpoints seem to run fine, but fail when an actual method call is made. Can anyone see any flaw in how I am putting this together? Thank you for your time - I have been running in circles with this for about a week!

  Read the article

< Previous Page | 82 83 84 85 86 87 88 89 90 91 92 93  | Next Page >