Search Results

Search found 23301 results on 933 pages for 'check in policy'.

Page 87/933 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• QoS basics on a Cisco ASA

  - by qbn

  Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

  Read the article

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• Output Caching with IIS7 - How To for an dynamic aspx page?

  - by Lieven Cardoen

  I have a RetrieveBlob.aspx that gets some query string variables and returns an asset. Eeach url corresponds to a unique asset. In the RetrieveBlob.aspx a Cache Profile is set. In Web.Config the profile looks like (under system.web tag: <caching> <outputCache enableOutputCache="true" /> <outputCacheSettings> <outputCacheProfiles> <add duration="14800" enabled="true" varyByParam="*" name="AssetCacheProfile" /> </outputCacheProfiles> </outputCacheSettings> </caching> Ok, this works fine. When I put a breakpoint in the code behind of RetrieveBlob.aspx, it gets triggered the first time, and all the other times not. Now, I throw away the Cache Profile and instead I'm having this in my Web.Config under System.WebServer: <caching> <profiles> <add extension=".swf" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".flv" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".gif" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".png" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".mp3" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".jpeg" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".jpg" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> </profiles> </caching> Now the caching doesn't work anymore. What am I doing wrong? Is it possible to configure under Caching tag of System.WebServer a Caching Profile for a Dynamic aspx page?

  Read the article

• Configuring https access on HP A5120 Switch

  - by GerryEgan

  I am trying to configure HTTPS management on a HP a5120 switch running Version 5.20.99, Release 2215 and not having much luck. I have followed the manual by creating an SSL policy first and then enabling the HTTPS server with the SSL policy: ssl server-policy sslpol ip https ssl-server-policy sslpol ip https enable When I try and log onto the switch with Google Chrome I get the following error: Error 107 (net::ERR_SSL_PROTOCOL_ERROR): SSL protocol error. When I look this up I have found references to errors due to TLS being used in SSL. I can find no way to specify the SSL version in the server policy. The manual has a configuration example that uses MSCEP to retrieve a certificate but in Windows 2008 R2 that feature is only available in Enterprise and Datacentre editions which I don't have. I have SSH configured and it is using a locally generated certificate so I'm not sure if I can use that but I'd like to if possible. Has anybody been able to setup HTTPS management on HP A series switches without MSCEP? Any and all help appreciated! here is a copy of my config with the interfaces removed: version 5.20.99, Release 2215 # sysname MYSYSNAME # irf domain 10 irf mac-address persistent timer irf auto-update enable undo irf link-delay # domain default enable system # telnet server enable # vlan 1 # vlan 100 description Management # radius scheme system primary authentication 127.0.0.1 1645 primary accounting 127.0.0.1 1646 user-name-format without-domain # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher authorization-attribute level 3 service-type ssh telnet terminal service-type web # stp enable # ssl server-policy sslpol pki-domain MYDOMAIN # interface NULL0 # interface Vlan-interface199 ip address 192.168.199.140 255.255.255.0 # interface GigabitEthernet1/0/1 poe enable stp edged-port enable # interface Ten-GigabitEthernet2/1/2 # dhcp-snooping # ntp-service unicast-server 192.168.1.71 # ssh server enable # ip https ssl-server-policy sslpol ip https enable # load xml-configuration # user-interface aux 0 1 user-interface vty 0 15 authentication-mode scheme

  Read the article

• SQL SERVER – Shrinking Database is Bad – Increases Fragmentation – Reduces Performance

  - by pinaldave

  Earlier, I had written two articles related to Shrinking Database. I wrote about why Shrinking Database is not good. SQL SERVER – SHRINKDATABASE For Every Database in the SQL Server SQL SERVER – What the Business Says Is Not What the Business Wants I received many comments on Why Database Shrinking is bad. Today we will go over a very interesting example that I have created for the same. Here are the quick steps of the example. Create a test database Create two tables and populate with data Check the size of both the tables Size of database is very low Check the Fragmentation of one table Fragmentation will be very low Truncate another table Check the size of the table Check the fragmentation of the one table Fragmentation will be very low SHRINK Database Check the size of the table Check the fragmentation of the one table Fragmentation will be very HIGH REBUILD index on one table Check the size of the table Size of database is very HIGH Check the fragmentation of the one table Fragmentation will be very low Here is the script for the same. USE MASTER GO CREATE DATABASE ShrinkIsBed GO USE ShrinkIsBed GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Create FirstTable CREATE TABLE FirstTable (ID INT, FirstName VARCHAR(100), LastName VARCHAR(100), City VARCHAR(100)) GO -- Create Clustered Index on ID CREATE CLUSTERED INDEX [IX_FirstTable_ID] ON FirstTable ( [ID] ASC ) ON [PRIMARY] GO -- Create SecondTable CREATE TABLE SecondTable (ID INT, FirstName VARCHAR(100), LastName VARCHAR(100), City VARCHAR(100)) GO -- Create Clustered Index on ID CREATE CLUSTERED INDEX [IX_SecondTable_ID] ON SecondTable ( [ID] ASC ) ON [PRIMARY] GO -- Insert One Hundred Thousand Records INSERT INTO FirstTable (ID,FirstName,LastName,City) SELECT TOP 100000 ROW_NUMBER() OVER (ORDER BY a.name) RowID, 'Bob', CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%2 = 1 THEN 'Smith' ELSE 'Brown' END, CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 1 THEN 'New York' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 5 THEN 'San Marino' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 3 THEN 'Los Angeles' ELSE 'Houston' END FROM sys.all_objects a CROSS JOIN sys.all_objects b GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Insert One Hundred Thousand Records INSERT INTO SecondTable (ID,FirstName,LastName,City) SELECT TOP 100000 ROW_NUMBER() OVER (ORDER BY a.name) RowID, 'Bob', CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%2 = 1 THEN 'Smith' ELSE 'Brown' END, CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 1 THEN 'New York' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 5 THEN 'San Marino' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 3 THEN 'Los Angeles' ELSE 'Houston' END FROM sys.all_objects a CROSS JOIN sys.all_objects b GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Check Fragmentations in the database SELECT avg_fragmentation_in_percent, fragment_count FROM sys.dm_db_index_physical_stats (DB_ID(), OBJECT_ID('SecondTable'), NULL, NULL, 'LIMITED') GO Let us check the table size and fragmentation. Now let us TRUNCATE the table and check the size and Fragmentation. USE MASTER GO CREATE DATABASE ShrinkIsBed GO USE ShrinkIsBed GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Create FirstTable CREATE TABLE FirstTable (ID INT, FirstName VARCHAR(100), LastName VARCHAR(100), City VARCHAR(100)) GO -- Create Clustered Index on ID CREATE CLUSTERED INDEX [IX_FirstTable_ID] ON FirstTable ( [ID] ASC ) ON [PRIMARY] GO -- Create SecondTable CREATE TABLE SecondTable (ID INT, FirstName VARCHAR(100), LastName VARCHAR(100), City VARCHAR(100)) GO -- Create Clustered Index on ID CREATE CLUSTERED INDEX [IX_SecondTable_ID] ON SecondTable ( [ID] ASC ) ON [PRIMARY] GO -- Insert One Hundred Thousand Records INSERT INTO FirstTable (ID,FirstName,LastName,City) SELECT TOP 100000 ROW_NUMBER() OVER (ORDER BY a.name) RowID, 'Bob', CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%2 = 1 THEN 'Smith' ELSE 'Brown' END, CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 1 THEN 'New York' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 5 THEN 'San Marino' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 3 THEN 'Los Angeles' ELSE 'Houston' END FROM sys.all_objects a CROSS JOIN sys.all_objects b GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Insert One Hundred Thousand Records INSERT INTO SecondTable (ID,FirstName,LastName,City) SELECT TOP 100000 ROW_NUMBER() OVER (ORDER BY a.name) RowID, 'Bob', CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%2 = 1 THEN 'Smith' ELSE 'Brown' END, CASE WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 1 THEN 'New York' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 5 THEN 'San Marino' WHEN ROW_NUMBER() OVER (ORDER BY a.name)%10 = 3 THEN 'Los Angeles' ELSE 'Houston' END FROM sys.all_objects a CROSS JOIN sys.all_objects b GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Check Fragmentations in the database SELECT avg_fragmentation_in_percent, fragment_count FROM sys.dm_db_index_physical_stats (DB_ID(), OBJECT_ID('SecondTable'), NULL, NULL, 'LIMITED') GO You can clearly see that after TRUNCATE, the size of the database is not reduced and it is still the same as before TRUNCATE operation. After the Shrinking database operation, we were able to reduce the size of the database. If you notice the fragmentation, it is considerably high. The major problem with the Shrink operation is that it increases fragmentation of the database to very high value. Higher fragmentation reduces the performance of the database as reading from that particular table becomes very expensive. One of the ways to reduce the fragmentation is to rebuild index on the database. Let us rebuild the index and observe fragmentation and database size. -- Rebuild Index on FirstTable ALTER INDEX IX_SecondTable_ID ON SecondTable REBUILD GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Check Fragmentations in the database SELECT avg_fragmentation_in_percent, fragment_count FROM sys.dm_db_index_physical_stats (DB_ID(), OBJECT_ID('SecondTable'), NULL, NULL, 'LIMITED') GO You can notice that after rebuilding, Fragmentation reduces to a very low value (almost same to original value); however the database size increases way higher than the original. Before rebuilding, the size of the database was 5 MB, and after rebuilding, it is around 20 MB. Regular rebuilding the index is rebuild in the same user database where the index is placed. This usually increases the size of the database. Look at irony of the Shrinking database. One person shrinks the database to gain space (thinking it will help performance), which leads to increase in fragmentation (reducing performance). To reduce the fragmentation, one rebuilds index, which leads to size of the database to increase way more than the original size of the database (before shrinking). Well, by Shrinking, one did not gain what he was looking for usually. Rebuild indexing is not the best suggestion as that will create database grow again. I have always remembered the excellent post from Paul Randal regarding Shrinking the database is bad. I suggest every one to read that for accuracy and interesting conversation. Let us run following script where we Shrink the database and REORGANIZE. -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Check Fragmentations in the database SELECT avg_fragmentation_in_percent, fragment_count FROM sys.dm_db_index_physical_stats (DB_ID(), OBJECT_ID('SecondTable'), NULL, NULL, 'LIMITED') GO -- Shrink the Database DBCC SHRINKDATABASE (ShrinkIsBed); GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Check Fragmentations in the database SELECT avg_fragmentation_in_percent, fragment_count FROM sys.dm_db_index_physical_stats (DB_ID(), OBJECT_ID('SecondTable'), NULL, NULL, 'LIMITED') GO -- Rebuild Index on FirstTable ALTER INDEX IX_SecondTable_ID ON SecondTable REORGANIZE GO -- Name of the Database and Size SELECT name, (size*8) Size_KB FROM sys.database_files GO -- Check Fragmentations in the database SELECT avg_fragmentation_in_percent, fragment_count FROM sys.dm_db_index_physical_stats (DB_ID(), OBJECT_ID('SecondTable'), NULL, NULL, 'LIMITED') GO You can see that REORGANIZE does not increase the size of the database or remove the fragmentation. Again, I no way suggest that REORGANIZE is the solution over here. This is purely observation using demo. Read the blog post of Paul Randal. Following script will clean up the database -- Clean up USE MASTER GO ALTER DATABASE ShrinkIsBed SET SINGLE_USER WITH ROLLBACK IMMEDIATE GO DROP DATABASE ShrinkIsBed GO There are few valid cases of the Shrinking database as well, but that is not covered in this blog post. We will cover that area some other time in future. Additionally, one can rebuild index in the tempdb as well, and we will also talk about the same in future. Brent has written a good summary blog post as well. Are you Shrinking your database? Well, when are you going to stop Shrinking it? Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, PostADay, SQL, SQL Authority, SQL Index, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, SQLServer, T SQL, Technology

  Read the article

• How to check if a variable is an integer? [closed]

  - by FyrePlanet

  I'm going through my C++ book and have currently made a working Guess The Number game. The game generates a random number based on current time, has the user input their guess, and then tells them whether it was too high, too low, or the correct number. The game functions fine if you enter a number, but returns 'Too High' if you enter something that is not a number (such as a letter or punctuation). Not only does it return 'too high', but it also continually returns it. I was wondering what I could do to check if the guess, as input by the user, is an integer and if it is not, to return 'Not a number. Guess again.' Here is the code. #include <iostream> #include <cstdlib> #include <ctime> using namespace std; int main() { srand(time(0)); // seed the random number generator int theNumber = rand() % 100 + 1; // random number between 1 and 100 int tries = 0, guess; cout << "\tWelcome to Guess My Number!\n\n"; do { cout << "Enter a guess: "; cin >> guess; ++tries; if (guess > theNumber) cout << "Too high!\n\n"; if (guess < theNumber) cout << "Too low!\n\n"; } while (guess != theNumber); cout << "\nThat's it! You got it in " << tries << " guesses!\n"; cout << "\nPress Enter to exit.\n"; cin.ignore(cin.rdbuf()->in_avail() + 1); return 0; }

  Read the article

• How to install a new TFS checkin policy on a TFS 2010 server?

  - by rhart

  Hi, We've recently upgraded our TFS server to TFS 2010 from 2008. We've been researching a couple new add-on checkin policies we want to install. The only problem is that all documentation I can find on adding new policies to the server appears to be specific to TFS 2008 or earlier. Those steps involve adding new keys in the registry which do not exist on our 2010 TFS server. Does anybody know where the process to install new checkin policies on a TFS 2010 server so they can be applied to Team Projects is documented? Thanks!

  Read the article

• What is the best policy for user account on a Windows 7 Media Center shared by the whole family

  - by Matt Spradley

  What is a good way to manage user accounts for a Windows 7 Media Center PC that is part of an entertainment center for a family? Each family member keeps most of their personal stuff on their own computer. I was thinking the simple approach would be to create an admin account for management and then just create a "Family" user account w/o a password that is the default account used by the media center. This account would be used for the PVR, playing blu rays, music, etc. I don't think it is practical for someone to have to log in every time they use the media center.

  Read the article

• How to install a new TFS checkin policy on a TFS 2010 server?

  - by rayrayrayraydog

  We've recently upgraded our TFS server to TFS 2010 from 2008. We've been researching a couple new add-on checkin policies we want to install. The only problem is that all documentation I can find on adding new policies to the server appears to be specific to TFS 2008 or earlier. Those steps involve adding new keys in the registry which do not exist on our 2010 TFS server. Does anybody know where the process to install new checkin policies on a TFS 2010 server so they can be applied to Team Projects is documented? Thanks!

  Read the article

• SQL SERVER – Disabled Index and Update Statistics

  - by pinaldave

  When we try to update the statistics, it throws an error as if the clustered index is disabled. Now let us enable the clustered index only and attempt to update the statistics of the table right after that. Have you ever come across the situation where a conversation never gets over and it continues even though original point of discussion has passed. I am facing the same situation in the case of Disabled Index. Here is the link to original conversations. SQL SERVER – Disable Clustered Index and Data Insert – Reader had a issue here with Disabled Index SQL SERVER – Understanding ALTER INDEX ALL REBUILD with Disabled Clustered Index – Reader asked the effect of Rebuilding Indexes The same reader asked me today – “I understood what the disabled indexes do; what is their effect on statistics. Is it true that even though indexes are disabled, they continue updating the statistics?“ The answer is very interesting: If you have disabled clustered index, you will be not able to update the statistics at all for any index. If you have enabled clustered index and disabled non clustered index when you update the statistics of the table, it automatically updates the statistics of the ALL (disabled and enabled – both) the indexes on the table. If you are not satisfied with the answer, let us go over a simple example. I have written necessary comments in the code itself to have a clear idea. USE tempdb GO -- Drop Table if Exists IF EXISTS (SELECT * FROM sys.objects WHERE OBJECT_ID = OBJECT_ID(N'[dbo].[TableName]') AND type IN (N'U')) DROP TABLE [dbo].[TableName] GO -- Create Table CREATE TABLE [dbo].[TableName]( [ID] [int] NOT NULL, [FirstCol] [varchar](50) NULL ) GO -- Insert Some data INSERT INTO TableName SELECT 1, 'First' UNION ALL SELECT 2, 'Second' UNION ALL SELECT 3, 'Third' UNION ALL SELECT 4, 'Fourth' UNION ALL SELECT 5, 'Five' GO -- Create Clustered Index ALTER TABLE [TableName] ADD CONSTRAINT [PK_TableName] PRIMARY KEY CLUSTERED ([ID] ASC) GO -- Create Nonclustered Index CREATE UNIQUE NONCLUSTERED INDEX [IX_NonClustered_TableName] ON [dbo].[TableName] ([FirstCol] ASC) GO -- Check that all the indexes are enabled SELECT OBJECT_NAME(OBJECT_ID), Name, type_desc, is_disabled FROM sys.indexes WHERE OBJECT_NAME(OBJECT_ID) = 'TableName' GO Now let us update the statistics of the table and check the statistics update date. -- Update the stats of table UPDATE STATISTICS TableName WITH FULLSCAN GO -- Check Statistics Last Updated Datetime SELECT name AS index_name, STATS_DATE(OBJECT_ID, index_id) AS StatsUpdated FROM sys.indexes WHERE OBJECT_ID = OBJECT_ID('TableName') GO Now let us disable the indexes and check if they are disabled using sys.indexes. -- Disable Indexes -- Disable Nonclustered Index ALTER INDEX [IX_NonClustered_TableName] ON [dbo].[TableName] DISABLE GO -- Disable Clustered Index ALTER INDEX [PK_TableName] ON [dbo].[TableName] DISABLE GO -- Check that all the indexes are disabled SELECT OBJECT_NAME(OBJECT_ID), Name, type_desc, is_disabled FROM sys.indexes WHERE OBJECT_NAME(OBJECT_ID) = 'TableName' GO Let us try to update the statistics of the table. -- Update the stats of table UPDATE STATISTICS TableName WITH FULLSCAN GO /* -- Above operation should thrown following error Msg 1974, Level 16, State 1, Line 1 Cannot perform the specified operation on table 'TableName' because its clustered index 'PK_TableName' is disabled. */ When we try to update the statistics it throws an error as it clustered index is disabled. Now let us enable the clustered index only and attempt to update the statistics of the table right after that. -- Now let us rebuild clustered index only ALTER INDEX [PK_TableName] ON [dbo].[TableName] REBUILD GO -- Check that all the indexes status SELECT OBJECT_NAME(OBJECT_ID), Name, type_desc, is_disabled FROM sys.indexes WHERE OBJECT_NAME(OBJECT_ID) = 'TableName' GO -- Check Statistics Last Updated Datetime SELECT name AS index_name, STATS_DATE(OBJECT_ID, index_id) AS StatsUpdated FROM sys.indexes WHERE OBJECT_ID = OBJECT_ID('TableName') GO -- Update the stats of table UPDATE STATISTICS TableName WITH FULLSCAN GO -- Check Statistics Last Updated Datetime SELECT name AS index_name, STATS_DATE(OBJECT_ID, index_id) AS StatsUpdated FROM sys.indexes WHERE OBJECT_ID = OBJECT_ID('TableName') GO We can clearly see that even though the nonclustered index is disabled it is also updated. If you do not need a nonclustered index, I suggest you to drop it as keeping them disabled is an overhead on your system. This is because every time the statistics are updated for system all the statistics for disabled indexesare also updated. -- Clean up DROP TABLE [TableName] GO The complete script is given below for easy reference. USE tempdb GO -- Drop Table if Exists IF EXISTS (SELECT * FROM sys.objects WHERE OBJECT_ID = OBJECT_ID(N'[dbo].[TableName]') AND type IN (N'U')) DROP TABLE [dbo].[TableName] GO -- Create Table CREATE TABLE [dbo].[TableName]( [ID] [int] NOT NULL, [FirstCol] [varchar](50) NULL ) GO -- Insert Some data INSERT INTO TableName SELECT 1, 'First' UNION ALL SELECT 2, 'Second' UNION ALL SELECT 3, 'Third' UNION ALL SELECT 4, 'Fourth' UNION ALL SELECT 5, 'Five' GO -- Create Clustered Index ALTER TABLE [TableName] ADD CONSTRAINT [PK_TableName] PRIMARY KEY CLUSTERED ([ID] ASC) GO -- Create Nonclustered Index CREATE UNIQUE NONCLUSTERED INDEX [IX_NonClustered_TableName] ON [dbo].[TableName] ([FirstCol] ASC) GO -- Check that all the indexes are enabled SELECT OBJECT_NAME(OBJECT_ID), Name, type_desc, is_disabled FROM sys.indexes WHERE OBJECT_NAME(OBJECT_ID) = 'TableName' GO -- Update the stats of table UPDATE STATISTICS TableName WITH FULLSCAN GO -- Check Statistics Last Updated Datetime SELECT name AS index_name, STATS_DATE(OBJECT_ID, index_id) AS StatsUpdated FROM sys.indexes WHERE OBJECT_ID = OBJECT_ID('TableName') GO -- Disable Indexes -- Disable Nonclustered Index ALTER INDEX [IX_NonClustered_TableName] ON [dbo].[TableName] DISABLE GO -- Disable Clustered Index ALTER INDEX [PK_TableName] ON [dbo].[TableName] DISABLE GO -- Check that all the indexes are disabled SELECT OBJECT_NAME(OBJECT_ID), Name, type_desc, is_disabled FROM sys.indexes WHERE OBJECT_NAME(OBJECT_ID) = 'TableName' GO -- Update the stats of table UPDATE STATISTICS TableName WITH FULLSCAN GO /* -- Above operation should thrown following error Msg 1974, Level 16, State 1, Line 1 Cannot perform the specified operation on table 'TableName' because its clustered index 'PK_TableName' is disabled. */ -- Now let us rebuild clustered index only ALTER INDEX [PK_TableName] ON [dbo].[TableName] REBUILD GO -- Check that all the indexes status SELECT OBJECT_NAME(OBJECT_ID), Name, type_desc, is_disabled FROM sys.indexes WHERE OBJECT_NAME(OBJECT_ID) = 'TableName' GO -- Check Statistics Last Updated Datetime SELECT name AS index_name, STATS_DATE(OBJECT_ID, index_id) AS StatsUpdated FROM sys.indexes WHERE OBJECT_ID = OBJECT_ID('TableName') GO -- Update the stats of table UPDATE STATISTICS TableName WITH FULLSCAN GO -- Check Statistics Last Updated Datetime SELECT name AS index_name, STATS_DATE(OBJECT_ID, index_id) AS StatsUpdated FROM sys.indexes WHERE OBJECT_ID = OBJECT_ID('TableName') GO -- Clean up DROP TABLE [TableName] GO Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Index, SQL Optimization, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: SQL Statistics

  Read the article

• could not bind socket while haproxy restart

  - by shreyas

  I m restarting HAproxy by following command haproxy -f /etc/haproxy/haproxy.cfg -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid) but i get following message [ALERT] 183/225022 (9278) : Starting proxy appli1-rewrite: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli2-insert: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli3-relais: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli4-backup: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy ssl-relay: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli5-backup: cannot bind socket my haproxy.cfg file looks likefollowing global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen appli1-rewrite 0.0.0.0:10001 cookie SERVERID rewrite balance roundrobin server app1_1 192.168.34.23:8080 cookie app1inst1 check inter 2000 rise 2 fall 5 server app1_2 192.168.34.32:8080 cookie app1inst2 check inter 2000 rise 2 fall 5 server app1_3 192.168.34.27:8080 cookie app1inst3 check inter 2000 rise 2 fall 5 server app1_4 192.168.34.42:8080 cookie app1inst4 check inter 2000 rise 2 fall 5 listen appli2-insert 0.0.0.0:10002 option httpchk balance roundrobin cookie SERVERID insert indirect nocache server inst1 192.168.114.56:80 cookie server01 check inter 2000 fall 3 server inst2 192.168.114.56:81 cookie server02 check inter 2000 fall 3 capture cookie vgnvisitor= len 32 option httpclose # disable keep-alive rspidel ^Set-cookie:\ IP= # do not let this cookie tell our internal IP address listen appli3-relais 0.0.0.0:10003 dispatch 192.168.135.17:80 listen appli4-backup 0.0.0.0:10004 option httpchk /index.html option persist balance roundrobin server inst1 192.168.114.56:80 check inter 2000 fall 3 server inst2 192.168.114.56:81 check inter 2000 fall 3 backup listen ssl-relay 0.0.0.0:8443 option ssl-hello-chk balance source server inst1 192.168.110.56:443 check inter 2000 fall 3 server inst2 192.168.110.57:443 check inter 2000 fall 3 server back1 192.168.120.58:443 backup listen appli5-backup 0.0.0.0:10005 option httpchk * balance roundrobin cookie SERVERID insert indirect nocache server inst1 192.168.114.56:80 cookie server01 check inter 2000 fall 3 server inst2 192.168.114.56:81 cookie server02 check inter 2000 fall 3 server inst3 192.168.114.57:80 backup check inter 2000 fall 3 capture cookie ASPSESSION len 32 srvtimeout 20000 option httpclose # disable keep-alive option checkcache # block response if set-cookie & cacheable rspidel ^Set-cookie:\ IP= # do not let this cookie tell our internal IP address #errorloc 502 http://192.168.114.58/error502.html #errorfile 503 /etc/haproxy/errors/503.http errorfile 400 /etc/haproxy/errors/400.http errorfile 403 /etc/haproxy/errors/403.http errorfile 408 /etc/haproxy/errors/408.http errorfile 500 /etc/haproxy/errors/500.http errorfile 502 /etc/haproxy/errors/502.http errorfile 503 /etc/haproxy/errors/503.http errorfile 504 /etc/haproxy/errors/504.http what is wrong with my aproach

  Read the article

• ActiveX component can't create Object Error? Check 64 bit Status

  - by Rick Strahl

  If you're running on IIS 7 and a 64 bit operating system you might run into the following error using ASP classic or ASP.NET with COM interop. In classic ASP applications the error will show up as: ActiveX component can't create object   (Error 429) (actually without error handling the error just shows up as 500 error page) In my case the code that's been giving me problems has been a FoxPro COM object I'd been using to serve banner ads to some of my pages. The code basically looks up banners from a database table and displays them at random. The ASP classic code that uses it looks like this: <% Set banner = Server.CreateObject("wwBanner.aspBanner") banner.BannerFile = "wwsitebanners" Response.Write(banner.GetBanner(-1)) %> Originally this code had no specific error checking as above so the ASP pages just failed with 500 error pages from the Web server. To find out what the problem is this code is more useful at least for debugging: <% ON ERROR RESUME NEXT Set banner = Server.CreateObject("wwBanner.aspBanner") Response.Write(err.Number & " - " & err.Description) banner.BannerFile = "wwsitebanners" Response.Write(banner.GetBanner(-1)) %> which results in: 429 - ActiveX component can't create object which at least gives you a slight clue. In ASP.NET invoking the same COM object with code like this: <% dynamic banner = wwUtils.CreateComInstance("wwBanner.aspBanner") as dynamic; banner.cBANNERFILE = "wwsitebanners"; Response.Write(banner.getBanner(-1)); %> results in: Retrieving the COM class factory for component with CLSID {B5DCBB81-D5F5-11D2-B85E-00600889F23B} failed due to the following error: 80040154 Class not registered (Exception from HRESULT: 0x80040154 (REGDB_E_CLASSNOTREG)). The class is in fact registered though and the COM server loads fine from a command prompt or other COM client. This error can be caused by a COM server that doesn't load. It looks like a COM registration error. There are a number of traditional reasons why this error can crop up of course. The server isn't registered (run regserver32 to register a DLL server or /regserver on an EXE server) Access permissions aren't set on the COM server (Web account has to be able to read the DLL ie. Network service) The COM server fails to load during initialization ie. failing during startup One thing I always do to check for COM errors fire up the server in a COM client outside of IIS and ensure that it works there first - it's almost always easier to debug a server outside of the Web environment. In my case I tried the server in Visual FoxPro on the server with: loBanners = CREATEOBJECT("wwBanner.aspBanner") loBanners.cBannerFile = "wwsitebanners" ? loBanners.GetBanner(-1) and it worked just fine. If you don't have a full dev environment on the server you can also use VBScript do the same thing and run the .vbs file from the command prompt: Set banner = Server.CreateObject("wwBanner.aspBanner") banner.BannerFile = "wwsitebanners" MsgBox(banner.getBanner(-1)) Since this both works it tells me the server is registered and working properly. This leaves startup failures or permissions as the problem. I double checked permissions for the Application Pool and the permissions of the folder where the DLL lives and both are properly set to allow access by the Application Pool impersonated user. Just to be sure I assigned an Admin user to the Application Pool but still no go. So now what? 64 bit Servers Ahoy A couple of weeks back I had set up a few of my Application pools to 64 bit mode. My server is Server 2008 64 bit and by default Application Pools run 64 bit. Originally when I installed the server I set up most of my Application Pools to 32 bit mainly for backwards compatibility. But as more of my code migrates to 64 bit OS's I figured it'd be a good idea to see how well code runs under 64 bit code. The transition has been mostly painless. Until today when I noticed the problem with the code above when scrolling to my IIS logs and noticing a lot of 500 errors on many of my ASP classic pages. The code in question in most of these pages deals with this single simple COM object. It took a while to figure out that the problem is caused by the Application Pool running in 64 bit mode. The issue is that 32 bit COM objects (ie. my old Visual FoxPro COM component) cannot be loaded in a 64 bit Application Pool. The ASP pages using this COM component broke on the day I switched my main Application Pool into 64 bit mode but I didn't find the problem until I searched my logs for errors by pure chance. To fix this is easy enough once you know what the problem is by switching the Application Pool to Enable 32-bit Applications: Once this is done the COM objects started working correctly again. 64 bit ASP and ASP.NET with DCOM Servers This is kind of off topic, but incidentally it's possible to load 32 bit DCOM (out of process) servers from ASP.NET and ASP classic even if those applications run in 64 bit application pools. In fact, in West Wind Web Connection I use this capability to run a 64 bit ASP.NET handler that talks to a 32 bit FoxPro COM server which allows West Wind Web Connection to run in native 64 bit mode without custom configuration (which is actually quite useful). It's probably not a common usage scenario but it's good to know that you can actually access 32 bit COM objects this way from ASP.NET. For West Wind Web Connection this works out well as the DCOM interface only makes one non-chatty call to the backend server that handles all the rest of the request processing. Application Pool Isolation is your Friend For me the recent incident of failure in the classic ASP pages has just been another reminder to be very careful with moving applications to 64 bit operation. There are many little traps when switching to 64 bit that are very difficult to track and test for. I described one issue I had a couple of months ago where one of the default ASP.NET filters was loading the wrong version (32bit instead of 64bit) which was extremely difficult to track down and was caused by a very sneaky configuration switch error (basically 3 different entries for the same ISAPI filter all with different bitness settings). It took me almost a full day to track this down). Recently I've been taken to isolate individual applications into separate Application Pools rather than my past practice of combining many apps into shared AppPools. This is a good practice assuming you have enough memory to make this work. Application Pool isolate provides more modularity and allows me to selectively move applications to 64 bit. The error above came about precisely because I moved one of my most populous app pools to 64 bit and forgot about the minimal COM object use in some of my old pages. It's easy to forget. To 64bit or Not Is it worth it to move to 64 bit? Currently I'd say -not really. In my - admittedly limited - testing I don't see any significant performance increases. In fact 64 bit apps just seem to consume considerably more memory (30-50% more in my pools on average) and performance is minimally improved (less than 5% at the very best) in the load testing I've performed on a couple of sites in both modes. The only real incentive for 64 bit would be applications that require huge data spaces that exceed the 32 bit 4 gigabyte memory limit. However I have a hard time imagining an application that needs 4 gigs of memory in a single Application Pool :-). Curious to hear other opinions on benefits of 64 bit operation. © Rick Strahl, West Wind Technologies, 2005-2011Posted in COM   ASP.NET  FoxPro  

  Read the article

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Quantifying the effects of partition mis-alignment

  - by Matt

  I'm experiencing some significant performance issues on an NFS server. I've been reading up a bit on partition alignment, and I think I have my partitions mis-aligned. I can't find anything that tells me how to actually quantify the effects of mis-aligned partitions. Some of the general information I found suggests the performance penalty can be quite high (upwards of 60%) and others say it's negligible. What I want to do is determine if partition alignment is a factor in this server's performance problems or not; and if so, to what degree? So I'll put my info out here, and hopefully the community can confirm if my partitions are indeed mis-aligned, and if so, help me put a number to what the performance cost is. Server is a Dell R510 with dual E5620 CPUs and 8 GB RAM. There are eight 15k 2.5” 600 GB drives (Seagate ST3600057SS) configured in hardware RAID-6 with a single hot spare. RAID controller is a Dell PERC H700 w/512MB cache (Linux sees this as a LSI MegaSAS 9260). OS is CentOS 5.6, home directory partition is ext3, with options “rw,data=journal,usrquota”. I have the HW RAID configured to present two virtual disks to the OS: /dev/sda for the OS (boot, root and swap partitions), and /dev/sdb for a big NFS share: [root@lnxutil1 ~]# parted -s /dev/sda unit s print Model: DELL PERC H700 (scsi) Disk /dev/sda: 134217599s Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 63s 465884s 465822s primary ext2 boot 2 465885s 134207009s 133741125s primary lvm [root@lnxutil1 ~]# parted -s /dev/sdb unit s print Model: DELL PERC H700 (scsi) Disk /dev/sdb: 5720768639s Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 34s 5720768606s 5720768573s lvm Edit 1 Using the cfq IO scheduler (default for CentOS 5.6): # cat /sys/block/sd{a,b}/queue/scheduler noop anticipatory deadline [cfq] noop anticipatory deadline [cfq] Chunk size is the same as strip size, right? If so, then 64kB: # /opt/MegaCli -LDInfo -Lall -aALL -NoLog Adapter #0 Number of Virtual Disks: 2 Virtual Disk: 0 (target id: 0) Name:os RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:65535MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 ... physical disk info removed for brevity ... Virtual Disk: 1 (target id: 1) Name:share RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:2793344MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 If it's not obvious, virtual disk 0 corresponds to /dev/sda, for the OS; virtual disk 1 is /dev/sdb (the exported home directory tree).

  Read the article

• DKIM, SPF, PTR records are not working properly with my domain

  - by shihon

  I configured my server and well authenticate email system with DKIM key, SPF record and PTR records, when i start to sent out mails from phplist interface to my users ~50000, my domain is spammed by google. In headers, signed by and mailed by tag shows by my domain : appmail.co, I also test my domain via check mail provide by port25, report is: This message is an automatic response from Port25's authentication verifier service at verifier.port25.com. The service allows email senders to perform a simple check of various sender authentication mechanisms. It is provided free of charge, in the hope that it is useful to the email community. While it is not officially supported, we welcome any feedback you may have at . Thank you for using the verifier, The Port25 Solutions, Inc. team ========================================================== Summary of Results SPF check: pass DomainKeys check: neutral DKIM check: pass Sender-ID check: pass SpamAssassin check: ham ========================================================== Details: HELO hostname: app.appmail.co Source IP: 108.179.192.148 mail-from: [email protected] SPF check details: Result: pass ID(s) verified: [email protected] DNS record(s): appmail.co. SPF (no records) appmail.co. 14400 IN TXT "v=spf1 +a +mx +ip4:108.179.192.148 ?all" appmail.co. 14400 IN A 108.179.192.148 DomainKeys check details: Result: neutral (message not signed) ID(s) verified: [email protected] DNS record(s): DKIM check details: Result: pass (matches From: [email protected]) ID(s) verified: header.d=appmail.co Canonicalized Headers: content-type:multipart/alternative;'20'boundary=047d7b2eda75d8544d04c17b6841'0D''0A' to:[email protected]'0D''0A' from:shashank'20'sharma'20'<[email protected]>'0D''0A' subject:Test'0D''0A' message-id:<CADnDhbH9aDBk3Ho2-CrG7gwOoD6RNX0sFq4bWL64+kmo=9HjWg@mail.gmail.com>'0D''0A' date:Sat,'20'2'20'Jun'20'2012'20'16:44:50'20'+0530'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=appmail.co;'20's=default;'20'h=Content-Type:To:From:Subject:Message-ID:Date:MIME-Version;'20'bh=GS6uwlT+weKcrrLJ2I+cjBtWPq9nvhwRlNAJebOiQOk=;'20'b=; Canonicalized Body: --047d7b2eda75d8544d04c17b6841'0D''0A' Content-Type:'20'text/plain;'20'charset=UTF-8'0D''0A' '0D''0A' Hello'20'Senders'0D''0A' '0D''0A' --047d7b2eda75d8544d04c17b6841'0D''0A' Content-Type:'20'text/html;'20'charset=UTF-8'0D''0A' '0D''0A' Hello'20'Senders'0D''0A' '0D''0A' --047d7b2eda75d8544d04c17b6841--'0D''0A' DNS record(s): default._domainkey.appmail.co. 14400 IN TXT "v=DKIM1; k=rsa; p=MHwwDQYJKoZIhvcNAQEBBQADawAwaAJhALGCOdMeZRxRHoatH7/KCvI1CKS0wOOsTAq0LLgPsOpMolifpVQDKOWT2zq/6LHVmDVjXLbnWO2d4ry/riy7ei66pLpnAV5ceIUSjBRusI8jcF9CZhPrh/OImsKVUb9ceQIDAQAB;" NOTE: DKIM checking has been performed based on the latest DKIM specs (RFC 4871 or draft-ietf-dkim-base-10) and verification may fail for older versions. If you are using Port25's PowerMTA, you need to use version 3.2r11 or later to get a compatible version of DKIM. Sender-ID check details: Result: pass ID(s) verified: [email protected] DNS record(s): appmail.co. SPF (no records) appmail.co. 14400 IN TXT "v=spf1 +a +mx +ip4:108.179.192.148 ?all" appmail.co. 14400 IN A 108.179.192.148 SpamAssassin check details: SpamAssassin v3.3.1 (2010-03-16) Result: ham (-0.1 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- -0.0 T_RP_MATCHES_RCVD Envelope sender domain matches handover relay domain 0.0 HTML_MESSAGE BODY: HTML included in message -0.5 BAYES_05 BODY: Bayes spam probability is 1 to 5% [score: 0.0288] -0.1 DKIM_VALID_AU Message has a valid DKIM or DK signature from author's domain 0.1 DKIM_SIGNED Message has a DKIM or DK signature, not necessarily valid -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature 0.5 SINGLE_HEADER_1K A single header contains 1K-2K characters ========================================================== Original Email Return-Path: <[email protected]> Received: from app.appmail.co (108.179.192.148) by verifier.port25.com id hp7qqo11u9cc for <[email protected]>; Sat, 2 Jun 2012 07:14:52 -0400 (envelope-from <[email protected]>) Authentication-Results: verifier.port25.com; spf=pass [email protected] Authentication-Results: verifier.port25.com; domainkeys=neutral (message not signed) [email protected] Authentication-Results: verifier.port25.com; dkim=pass (matches From: [email protected]) header.d=appmail.co Authentication-Results: verifier.port25.com; sender-id=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=appmail.co; s=default; h=Content-Type:To:From:Subject:Message-ID:Date:MIME-Version; bh=GS6uwlT+weKcrrLJ2I+cjBtWPq9nvhwRlNAJebOiQOk=;b=pNw3UQNMoNyZ2Ujv8omHGodKVu/55S8YdBEsA5TbRciga/H7f+5noiKvo60vU6oXYyzVKeozFHDoOEMV6m5UTgkdBefogl+9cUIbt5CSrTWA97D7tGS97JblTDXApbZH; Received: from mail-pb0-f46.google.com ([209.85.160.46]:57831) by app.appmail.co with esmtpa (Exim 4.77) (envelope-from <[email protected]>) id 1SamIF-00055f-Om for [email protected]; Sat, 02 Jun 2012 16:44:51 +0530 Received: by pbbrp8 with SMTP id rp8so4165728pbb.5 for <[email protected]>; Sat, 02 Jun 2012 04:14:51 -0700 (PDT) MIME-Version: 1.0 Received: by 10.68.216.33 with SMTP id on1mr19414885pbc.105.1338635690988; Sat, 02 Jun 2012 04:14:50 -0700 (PDT) Received: by 10.143.66.13 with HTTP; Sat, 2 Jun 2012 04:14:50 -0700 (PDT) Date: Sat, 2 Jun 2012 16:44:50 +0530 Message-ID: <CADnDhbH9aDBk3Ho2-CrG7gwOoD6RNX0sFq4bWL64+kmo=9HjWg@mail.gmail.com> Subject: Test From: shashank sharma <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=047d7b2eda75d8544d04c17b6841 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - app.appmail.co X-AntiAbuse: Original Domain - verifier.port25.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - appmail.co --047d7b2eda75d8544d04c17b6841 Content-Type: text/plain; charset=UTF-8 Hello Senders --047d7b2eda75d8544d04c17b6841 Content-Type: text/html; charset=UTF-8 Hello Senders --047d7b2eda75d8544d04c17b6841-- I also tried to send mail on yahoo , rediff but i get mails in spam. Please help me to sort out this issue

  Read the article

• MegaCli newly created disk doesn't appear under /dev/sdX

  - by Henry-Nicolas Tourneur

  After having successfully added 2 new disks in a new RAID virtual drive (background initialization done), I would have exepected it to appear under /dev/sdh but it's not there (so, unusable). The system is running a CentOS 5.2 64 bits, HAL and udev daemons are running, not records of any sdh apparition under the messsage log file or in dmesg, only MegaCli do see that virtual drive. Any idea ? Some data: [root@server ~]# ./MegaCli -LDInfo -LALL -a0 Adapter 0 -- Virtual Drive Information: Virtual Disk: 0 (target id: 0) Name: RAID Level: Primary-1, Secondary-0, RAID Level Qualifier-0 Size:139392MB State: Optimal Stripe Size: 64kB Number Of Drives:2 Span Depth:1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Virtual Disk: 1 (target id: 1) Name: RAID Level: Primary-1, Secondary-0, RAID Level Qualifier-0 Size:285568MB State: Optimal Stripe Size: 64kB Number Of Drives:2 Span Depth:1 Default Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteBack, ReadAheadNone, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default [root@server ~]# ls -l /dev/disk/by-id/scsi-360* lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09 -> ../../sda lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09-part1 -> ../../sda1 lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36001ec90f82fe100108ca0a704098d09-part2 -> ../../sda2 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe07e78f94940c0000a0ee -> ../../sdf lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe07e78f94940c0000a0ee-part1 -> ../../sdf1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe972a3f91240a0000005f -> ../../sdb lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fe972a3f91240a0000005f-part1 -> ../../sdb1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fea7e18f94640c000020ec -> ../../sde lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fea7e18f94640c000020ec-part1 -> ../../sde1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0feb7da8f94340c0000203d -> ../../sdd lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0feb7da8f94340c0000203d-part1 -> ../../sdd1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fed7d78f94040c000080b7 -> ../../sdc lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a028e0fed7d78f94040c000080b7-part1 -> ../../sdc1 lrwxrwxrwx 1 root root 9 Nov 17 2010 /dev/disk/by-id/scsi-36090a05830145e58e0b9c479000010a1 -> ../../sdg lrwxrwxrwx 1 root root 10 Nov 17 2010 /dev/disk/by-id/scsi-36090a05830145e58e0b9c479000010a1-part1 -> ../../sdg1

  Read the article

• Linux service --status-all shows "Firewall is stopped." what service does firewall refer to?

  - by codewaggle

  I have a development server with the lamp stack running CentOS: [Prompt]# cat /etc/redhat-release CentOS release 5.8 (Final) [Prompt]# cat /proc/version Linux version 2.6.18-308.16.1.el5xen ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-52)) #1 SMP Tue Oct 2 22:50:05 EDT 2012 [Prompt]# yum info iptables Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * base: mirror.anl.gov * extras: centos.mirrors.tds.net * rpmfusion-free-updates: mirror.us.leaseweb.net * rpmfusion-nonfree-updates: mirror.us.leaseweb.net * updates: mirror.steadfast.net Installed Packages Name : iptables Arch : x86_64 Version : 1.3.5 Release : 9.1.el5 Size : 661 k Repo : installed .... Snip.... When I run: service --status-all Part of the output looks like this: .... Snip.... httpd (pid xxxxx) is running... Firewall is stopped. Table: filter Chain INPUT (policy DROP) num target prot opt source destination 1 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) num target prot opt source destination 1 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Chain RH-Firewall-1-INPUT (2 references) ....Snip.... iptables has been loaded to the kernel and is active as represented by the rules being displayed. Checking just the iptables returns the rules just like status all does: [Prompt]# service iptables status Table: filter Chain INPUT (policy DROP) num target prot opt source destination 1 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) num target prot opt source destination 1 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Chain RH-Firewall-1-INPUT (2 references) .... Snip.... Starting or restarting iptables indicates that the iptables have been loaded to the kernel successfully: [Prompt]# service iptables restart Flushing firewall rules: [ OK ] Setting chains to policy ACCEPT: filter [ OK ] Unloading iptables modules: [ OK ] Applying iptables firewall rules: [ OK ] Loading additional iptables modules: ip_conntrack_netbios_n[ OK ] [Prompt]# service iptables start Flushing firewall rules: [ OK ] Setting chains to policy ACCEPT: filter [ OK ] Unloading iptables modules: [ OK ] Applying iptables firewall rules: [ OK ] Loading additional iptables modules: ip_conntrack_netbios_n[ OK ] I've googled "Firewall is stopped." and read a number of iptables guides as well as the RHEL documentation, but no luck. As far as I can tell, there isn't a "Firewall" service, so what is the line "Firewall is stopped." referring to?

  Read the article

• How to validate if all check boxes are ticked in jQuery?

  - by Jude

  I am a beginner in jQuery and I was wondering how to validate the form before submission specifically for check boxes. I am creating a simple check list form where my user would tick a check box if he finished that step. What I am planning to do is that, the script would prevent the form submission if there is an "unticked" checkbox and highlight it with a color. Here's my code : <!doctype html> <html> <head> <meta charset="utf-8"> <title>checkbox</title> <style> .error { background-color:#F00; } .valid { background-color:#0F0; } </style> <script type="application/javascript" src="http://code.jquery.com/jquery-1.8.2.min.js"> </script> <script type="application/javascript"> function validateAll() { $(".tick").change(function(){ if ($('.tick:checked').length == $('.tick').length) { $('#container').removeClass(); $('#container').addClass('error'); } else { $('#container').removeClass(); $('#container').addClass('valid'); } }); } </script> </head> <body> <div id="container"><input class="tick" id="option1" type="checkbox"></div> <div id="container"><input class="tick" id="option1" type="checkbox"></div> <input id="button" type="button" onClick="validateAll();" value="check"> </body> </html> So what I am trying to do here is when the user clicks the button, the script will highlight all the unchecked check box with red and highlight all checked with green. However, my script is not functioning. What is wrong with my script? Any suggestions on a more efficient way to do this?

  Read the article

• Create mirror software raid with bad blocks hdd. How to check data integrity?

  - by rumburak

  There is error in System event log like this one: "The device, \Device\Harddisk1\DR1, has a bad block." Because of above I created Raid 1 on this disk and other one. I'm using Windows Server 2008 R2 software RAID volumes. Volume in Disk Manager is marked as "Failed Redundancy" and "At Risk". I could command to "Reactivate Disk" and it's starts to re-sync, but after a while it stops and returns to previous state. It stops re-sync on bad block on old disk and creates same error in System event log. Old disk status is Errors, new disk status is Online. How can I check that there is exact copy of the old disk on new one ? It is server machine so I would prefer to keep it running during this check.

  Read the article

• With Monit, how do I restart a process when a directory timestamp check fails?

  - by Alterscape

  In my /etc/monit/monitrc I have the following lines: check process foo_server with pidfile /var/run/bwam_server.pid start program = "/Users/foo/foo_server.sh start" stop program = "/Users/foo/foo_server.sh stop" check directory foo_data path "/Users/foo/Library/Application Support/foo_server/data" if timestamp > 1 minute then alert #if timestamp > 1 minute then restart foo_server I know I shouldn't have some of this stuff in my home directory, but this aside: if I uncomment the last line, Monit tells me syntax error on foo_server -- but I am, as far as I understand, correctly defining the process -- how else do I reference it?

  Read the article

• What is the command to check if a command's results mention OK?

  - by Manuel

  Alright, so I was playing around with changing MTU size and wanted to make a batch file to automatically lower it and then raise it later. This is probably simple, but I just can't figure it out. Point is, is there a way to run a command, which would normally echo out "ok" but check to see if it does say ok? And if it doesn't say ok then, to end the rest of the file from running and exit out. The command I'm using is netsh interface ipv4 set subinterface "Local Area Connection" mtu=386 store=persistent which, as I mentioned above prints out an OK. I just want to check if it did run correctly, and if not, then do __

  Read the article

• What's the easiest way to allow Exchange 2003 remote (no MSO client) users check their Mailbox size?

  - by Myrddin Emrys

  We are migrating from Exchange 2003 with no quota settings to Exchange 2010 with limited mailbox sizes. We are trying to get users to clean their mailboxes prior to the move to reduce the transfer load, as well as to comply with new quotas on the 2010 system. But many users access their mail through webmail only. I cannot see a way for users to access their mail store size in this manner. Has anyone else run into this problem? Is there a good way to easily let users check their own mailbox size? The only thing I've come up with as a workaround is a report that IT generates and mail-merge it out to users daily with their current mailbox size. This is cumbersome and time consuming compared to a way for them to check their own mailbox size however.

  Read the article

• Powershell and DfsrConfigurationFromAD - how to check all servers are updated?

  - by user57792

  I have two Win2012R2 servers (SERVER1 and SERVER2) that uses DFS Replication for keeping a couple of folders synchronized. Using the following Powershell-script that i run on SERVER1 I disconnect it from the group: Set-DfsrConnection -GroupName "Group1" -SourceComputerName "SERVER1" -DestinationComputerName "SERVER2" -DisableConnection $True; And to update both the servers with the configuration I run the command: Update-DfsrConfigurationFromAD -ComputerName "SERVER1","SERVER2" Now the question is, how can check on SERVER1 that SERVER2 has gotten the updated information from the AD so that I can be sure that the connection has been disabled? Usually it takes around 10-30 seconds after the Update-DfsrConfigurationFromAD command has been run before the DFS Management on SERVER2 gets updated but I need some kind of a "check and sleep loop" in my code. I've tried checking event logs and using Invoke-Command {Get-DfsrConnection} from PM-SERVER01 but nothing seems to work.

  Read the article

• How can I check for a string match AND an empty file in the same if/then bash script statement?

  - by Mike B

  I'm writing a simple bash script to do the following: 1) Check two files (foo1 and foo2). 2) If foo1 is different from foo2 and foo1 NOT blank, send an email. 3) If foo1 is the same as foo2... or foo1 is blank... do nothing. The blank condition is what's confusing me. Here's what I've got to start with: diff --brief <(sort ./foo1) <(sort ./foo2) >/dev/null comp_value=$? if [ $comp_value -ne 0 ] then mail -s "Alert" [email protected] <./alertfoo fi Obviously this doesn't check for blank contents. Any thoughts on how to do that?

  Read the article

• What's the best practice for make username check like Twitter ?

  - by Space Cracker

  I develop registration form and it have username field, and it's required to be like twitter username check ( real time check ) .. i already develop as in every textbox key up I use jquery to pass textbox.Text to page that return if is username exist or not as following code : function Check() { var userName = $('#<%= TextBox1.ClientID %>').val(); if (userName.length < 3) { $('#checkUserNameDIV').html("user name must be between 3 and 20"); return; } $('#checkUserNameDIV').html('<img src="loader.gif" />'); //setTimeout("CheckExistance('" + userName + "')", 5000); CheckExistance(userName); } function CheckExistance(userName) { $.get( "JQueryPage.aspx", { name: userName }, function(result) { var msg = ""; if (result == "1") msg = "Not Exist " + '<img src="unOK.gif" />'; else if (result == "0") msg = "Exist" ; else if (result == "error") msg = "Error , try again"; $('#checkUserNameDIV').html(msg); } ); } but i don't know if is it the best way to do that ? specially i do check every keyup .. is there any design pattern for this problem or nay good practice for doing that ?

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >