Search Results

Search found 3141 results on 126 pages for 'crashpoint zero'.

Page 87/126 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• MD RAID 1 with external bitmap doesn't fully resync

  - by user64744

  I have an interesting configuration: dual boot system with a RAID 1 that needs to be visible in both Windows and Linux. The Windows install is Win 7 Enterprise, and the Linux install is Kubuntu 10.04. To get the RAID to work, I set it up using Windows's "Dynamic Disks" RAID 1, and brought it up in Linux using MD with no persistent superblock, and a write-intent bitmap on another partition. (Without this bitmap, MD had no way of knowing that the array was in sync, and would do a complete resync every time the array started.) The array is assembled like so: mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 I expected that the first time I ran this command, it would resync the array, write out a bitmap with no dirty chunks, and all would be good. This wasn't the case: after completing the resync, the bitmap was mostly clean, but about 5% dirty blocks remained, as revealed by mdadm -X /var/local/md1.bitmap I didn't mount the filesystem on /dev/md1 or touch it in any other way. I then found that stopping and restarting the array: mdadm --stop /dev/md1 mdadm --build /dev/md1 -l 1 -n 2 -b /var/local/md1.bitmap /dev/sdb2 /dev/sdc2 did indeed read in the bitmap, with an ensuing resync that went quickly because most of the blocks were marked clean. The confusing part is that this resync further reduced the number of dirty blocks, but still did not remove all of them. By repeatedly stopping and restarting I could slowly bring the dirty block count down to around 0.6%, where it seemed to level out. Any ideas what could be causing this? It smells to me of a race condition somewhere that leads to blocks either being skipped over during synchronization or not properly cleared from the bitmap, but I really have no evidence to prove this. It doesn't look like hardware issues since both drives are new and have zero read errors and reallocated sectors reported by smartctl -a.

  Read the article

• Weird mouse behaviour. Debian wheezy

  - by DevNoob

  When I move my mouse slowly over the desktop the pointer jumps often a few pixels (one or two) in the opposite direction of which I move my mouse. Horribly when trying to set the cursor around some semicolons in eclipse. I guess this is the result of a wrong set resolution of it. I suppose this is because the mouse was set initially really fast and even if I do xset 1/2 3, the mouse is just to fast and unprecise for me. It aready tried to configure the xorg.conf like this: Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "Device" "/dev/mouse" Option "Protocol" "Auto" Option "Name" "Logitech G3" Option "Resolution" "2000" EndSection But with no effect. Maybe because there is no /dev/mouse. This ist the content of dev. Maybe you can tell me which one is the mouse. autofs block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dvd dvdrw fd fd0 full fuse fw0 hidraw0 hidraw1 hpet input kmsg log loop0 loop1 loop2 loop3 loop4 loop5 loop6 loop7 loop-control MAKEDEV mapper mcelog mem net network_latency network_throughput null nvidia0 nvidiactl oldmem port ppp printer psaux ptmx pts random rfkill root rtc rtc0 sda sda1 sda2 sda3 sda5 sda6 sda7 sda8 sdb sdb1 sg0 sg1 sg2 shm snapshot snd sndstat sr0 stderr stdin stdout tty tty0 tty1 tty10 tty11 tty12 tty13 tty14 tty15 tty16 tty17 tty18 tty19 tty2 tty20 tty21 tty22 tty23 tty24 tty25 tty26 tty27 tty28 tty29 tty3 tty30 tty31 tty32 tty33 tty34 tty35 tty36 tty37 tty38 tty39 tty4 tty40 tty41 tty42 tty43 tty44 tty45 tty46 tty47 tty48 tty49 tty5 tty50 tty51 tty52 tty53 tty54 tty55 tty56 tty57 tty58 tty59 tty6 tty60 tty61 tty62 tty63 tty7 tty8 tty9 ttyS0 ttyS1 ttyS2 ttyS3 uinput urandom usb vcs vcs1 vcs2 vcs3 vcs4 vcs5 vcs6 vcs7 vcsa vcsa1 vcsa2 vcsa3 vcsa4 vcsa5 vcsa6 vcsa7 vga_arbiter vmci vmmon vmnet0 vmnet1 vmnet8 vsock watchdog xconsole zero So my question is: How do I setup my mouse correctly in Debian wheezy?

  Read the article

• What steps to take when CPAN installation fails?

  - by pythonic metaphor

  I have used CPAN to install perl modules on quite a few occasions, but I've been lucky enough to just have it work. Unfortunately, I was trying to install Thread::Pool today and one of the required dependencies, Thread::Converyor::Monitored failed the test: Test Summary Report ------------------- t/Conveyor-Monitored02.t (Wstat: 65280 Tests: 89 Failed: 0) Non-zero exit status: 255 Parse errors: Tests out of sequence. Found (2) but expected (4) Tests out of sequence. Found (4) but expected (5) Tests out of sequence. Found (5) but expected (6) Tests out of sequence. Found (3) but expected (7) Tests out of sequence. Found (6) but expected (8) Displayed the first 5 of 86 TAP syntax errors. Re-run prove with the -p option to see them all. Files=3, Tests=258, 6 wallclock secs ( 0.07 usr 0.03 sys + 4.04 cusr 1.25 csys = 5.39 CPU) Result: FAIL Failed 1/3 test programs. 0/258 subtests failed. make: *** [test_dynamic] Error 255 ELIZABETH/Thread-Conveyor-Monitored-0.12.tar.gz /usr/bin/make test -- NOT OK //hint// to see the cpan-testers results for installing this module, try: reports ELIZABETH/Thread-Conveyor-Monitored-0.12.tar.gz Running make install make test had returned bad status, won't install without force Failed during this command: ELIZABETH/Thread-Conveyor-Monitored-0.12.tar.gz: make_test NO What steps do you take to start seeing why an installation failed? I'm not even sure how to begin tracking down what's wrong.

  Read the article

• Arch Linux drops me on my school network

  - by Kravlin

  I'm running a Lenovo X61 which i carry around my college for getting on the internet at various points in the day. The network has always been finicky but recently it's gotten worse. I'll connect using iwconfig, get an ip from dhcpcd and log in using vpnc to their system. Sometimes I'll stay connected for hours but most of the time within 30 seconds my network traffic will drop to zero and i'll be unable to do anything. My computer still belives it's connected, however to try again i need to put my wireless interface down, put it back up and try again. It's gotten so bad that i've got a window on my computer pinging yahoo or google constantly in order to know if i'm still able to get online. I know other people who have used Arch Linux that don't have the same problems as well as people who use Ubuntu who haven't had any problems either. It seems like my computer is a special case. Does anyone have any suggestions on how to fix it? dmesg doesn't show anything out of the ordinary going on and i don't know where else to look for errors or other things to try. Edit: this doesn't happen on my home network. It's a problem that only happens at school.

  Read the article

• Solaris 10: How to image a machine?

  - by nonot1

  I've got a Solaris 10 workstation that I'd like to create a full image backup from. The machine has 2 drives, one UFS for system root, and 1 ZFS for data storage. I intend to add a third HD to keep the backup images of both primary drives (including any zfs snapshots). The purpose is not disaster recovery, but rather to allow me to easily blow away a series of application installation/configuration changes I intend to try. What's the best way to do this? I'm not too familiar with Solaris, but have some basic Linux knowledge. I looked at CloneZilla, but it does not support Solaris. I'm OK with just a dd | gzip > image style solution, but I'd need some way to first zero-out the non-used blocks on the primary drives to aid gzip. They are are much larger than my 3rd drive, but hardly have any real data. Update to clarify: I specifically want to avoid using any file-system snapshot functionality, because part of the app configuration changes involve/depend slightly on existing and new snapshots. Ideally the full collection of snapshots should be part of the backup. Virtualization not an option, because the goal is to do performance evaluation on a very specific HW configuration. For the same reason, the spurious "back up" snapshots could skew performance data. Thank you

  Read the article

• CentOS Latency High Troubleshooting

  - by Sarah Weinberger

  I have two CentOS servers connected via a 10 Gb fiber optic cable with a network emulator connected between them. All three units sit on a desk in the lab. There is also a regular 1 Gbit Ethernet cable connected to each of the machines, which provide internet connectivity. When I set the latency to something roughly below 30 ms, all is fine. When the latency gets to 70ms and above, and definitely 130ms, the network layer suspends. For instance, if I set the latency (delay) to 70ms, then launching TeamViewer (or any other application that uses network connectivity) never happens or does not work. There is no timeout message, simply no response. I have to lower to latency back down to zero to see any response and have the box start working. What is the problem and how would I go about fixing it? It seems to me some sort of setting in Linux causes one of the CentOS networking drivers to sit in an infinite loop or something. eth0 is the connection to the internet, all settings are default eth2 is the 10 Gbit fiber optic connection to the other computer with the MTU set to 9600 with all other parameters at default values.

  Read the article

• Understanding encryption Keys

  - by claws

  Hello, I'm really embarrassed to ask this question but its the fact that I don't know anything about encryption. I always avoided it. I don't understand the concept of encryption keys (public key, private key, RSA key, DSA key, PGP Key, SSH key & what not) . I did encounter these in regular basis but as I said I always avoided them. Here are few instances where I encountered: Creating Account: A public RSA or DSA key will be needed for an account. Send the key along with your desired account name to [email protected] I really don't know what are RSA/DSA or How to get their keys? Do I need to register some where for that? Mailing: I'm unable to recall exactly but I've seen some mails have some attachments like signature or the mail footer will have something called PGP signature etc.. I really don't get its concept. GIT Version control: I created account in assembla.com (for private GIT repo) and it asked me to enter "SSH keys" to my profile. Where am I gonna get these? Why do I need it? Isn't SSH related to remote login (like remote desktop or telnet)? How are these two SSHs related & differ? I don't know in how many more situations I'm going to encounter these things. I'm really confused and have no clue about where to start & how to proceed to learn these things. Kindly someone point me in correct direction. Note: I've absolutely zero interested in encryption related topics. So, there is no way I'm going to read a graduate level book on this subject. I just want to clear my concepts without going into much depth.

  Read the article

• CLI package to replace Plesk

  - by dotancohen

  Myself and another programmer are tasked with maintaining a few webservers. I prefer CLI tools, she prefers Plesk. However, I am adamant about not installing Plesk for quite a few reasons. I have written a small Python script for adding new domains, and now I am about to add the ability to configure email addresses while abstracting the details of Postfix from her. Before I go that route, I have googled to see if anything already exists, and am surprised that I have come up with nothing! Are there any mature, stable "control panels" or "server admin" tools like Plesk, but which are accessed via the CLI over SSH? I am looking for the following features: Add / remove / configure domains served by Apache. Add / remove / configure email boxes and mail groups. Add / remove MySQL databases, users, and configure users to databases. Provide basic monitoring of "server health", that is: memory usage, disk usage, CPU usage, bandwidth usage. Possibly set up STFP accounts so that only specific FTP users could access specific /var/www/someSite/ directories. Note that I was unsure if this question is OT for ServerFault. As per the ServerFault about page (There seems to be no more FAQ) this question meets two of the "ask about" criterion and zero of the "don't ask about" with the possible exception of being opinion-based. Therefore, to keep on-topic, I would like to know about the available applications but we should be subjective and less opinionated. Thank you!

  Read the article

• 10 GigE interfaces limits single connection throughput to 1 Gb on a ProCurve 4208vl

  - by wazoox

  The setup is as follow : 3 Linux servers with Intel CX4 10 GigE controllers and an X-Serve with a Myricom 10 GigE CX4 controller are connected to a ProCurve 4208vl switch, with a myriad of other machines connected through good ol' 1000 base-T. The interfaces are actually set up as 10 Gig, according to both the switch monitoring interface and the servers (ethtool, etc). However a single connection between two 10 GigE equipped machines through the switch is limited to exactly 1Gb. If I connect two of the 10 GigE machines directly with a CX4 cable, netperf reports the link bandwidth as 9000 Mb/s. NFS achieves about 550 MB/s transfers. But when I'm using the switch, the connection tops at 950 Mb/s through netperf and 110 MB/s with NFS. When I open several connections from 3 of the machines to the 4th, I get 350 MB/s of NFS transfer speed. So each individual 10 GigE ports actually can reach much more than 1 Gb, but individual connections are strictly limited to 1 Gb. Conclusion : the 10 GigE connection through the switch behaves exactly like a trunk of 10 1 Gb connections. That doesn't make any sense to me, unless HP planned these ports only for cascading switches or strictly for many-clients-to-single-server connection. Unfortunately this is NOT the envisioned setup, we need big throughput from machine to machine. Is this a not-so-known (or carefully hidden...) limitation of this type of switch? Should I suggest seppuku to the HP representative? Does anyone have any idea on how to enable a proper behaviour ? I upgraded for an hefty price from bonded 1Gb links to 10 GigE and see exactly ZERO gain! That's absolutely unacceptable.

  Read the article

• What is causing sudden freezing during running real-time program?

  - by Trevor Boyd Smith

  So I run a high intensive (CPU/GPU) real-time program. During normal execution suddenly everything freezes for 1-4 seconds. I opened "Process Explorer" in the background to help gain insight and maybe identify something. Here is what the CPU/GPU graphs looks like when I align them in time: Notice the 4 distinct drops in both the CPU/GPU. You can see that it goes from some sort of positive CPU/GPU usage to almost zero. These drops in the graph align with when the real-time program suddenly freezes. How do I find what is causing these sudden drops? NOTE: When you put your mouse over the graph it tells you the time, accurate to the second, for where your cursor is. Maybe this mouse over feature could be helpful in some way (e.g. what if you had a log of all processes every 100ms). EDIT: The real-time program is a video game and so I can't watch some sort of instrumentation while the video game is running. I need a solution that let's you look back in time somehow to see what was happening when the slow down occurred. EDIT: RE - Recording Data vs using real-time monitor: So the windows performance recorder is for some reason not recording what I expect it to record. So I switched to using "perfmon" and then opening it's "resource monitor". RE - Setting it up so I can view real-time monitor: In the video game I set it to spectate and then put the video game in "windowed" mode so that I can view the real time display that Resource Monitor has. Now that I can get semi-real time (only once per second... how do you get more than once per second?) I started looking at the various real time data readouts. Getting to the cause: I noticed a strong correlation in high disk IO and low CPU usage (which is also seen by having in-game freezing). How do you use resource monitor to find out who is doing all this offending disk IO?

  Read the article

• PHP Causing Segmentation Fault & Apache Blank Response

  - by Joe

  I recently updated a Debian Lenny server to php 5.3,5 using the dotdeb source. Soon after doing so certain (but not all) sites on the server stopped responding to requests. A blank response would be returned - no headers, no content, nothing. I found this related question on stackoverflow which seems to describe something similar and used the same code the user had in their answer to see if I could replicate the issue: <?php class A { public function __construct() { new B; } } class B { public function __construct() { new A; } } new A; print 'Loaded Class A'; ?> This triggered the problem - the page returned absolutely nothing despite the original question stating this was fixed in PHP 5.5.0. No CPU block as you'd expect, no wait, just an almost instant zero response. I then ran this same code from the cli (php -f test.php) and the only output I got was 'Segmentation fault'. Tailing the kernel log I've spotted: Feb 16 07:04:06 creature kernel: [192203.269037] php[17710] general protection ip:76ef37 sp:7fff155e9bb0 error:0 in php5[400000+870000] Feb 16 08:57:31 creature kernel: [199639.699854] apache2[31136]: segfault at 7fff13a84fe0 ip 7f730514ea40 sp 7fff13a85008 error 6 in libphp5.so[7f7304ce8000+915000] All extremely odd and I'm not sure what it's pointing to/what I should do to debug this further. As I said some sites work but code such as the above definitely trigger it. Not that the sites I want to server have code like that - it's just an example. Any help is much appreciated!

  Read the article

• How to test/debug bad network wiring?

  - by Jack Lloyd

  I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

  Read the article

• What can cause a kernel hang on redhat 4?

  - by Ivan Buttinoni

  I've to solve a nasty problem on a ten machine "cluster": randomly one of these machine hang during an hard computation, sometime still ping sometime not. The problem was described me at the phone, I've still no touch/see these machine, so I can't be more precise. It seem there's no (real) keyboard or monitor linked to them, so I haven't nothing about keyboard led or messages on monitor. Don't worry, what I really need is some suggestion where to search the problem, some suggestions on what can cause a kernel hang on a working machine. I also see this post, but seem same need on a different situation. My ideas since now: - HW problem (ram, cpu, fan etc.) - bad autofs configuration - bad nfs(?) configuration - presence of a trojan/hacker/etc - /dev/"swap" linked to /dev/zero - kernel out of memory(??) - kernel bugged In other words I try to imagine what kind of envent can occour that can crash the kernel insted of the application that generate the event. What hang have YOU experienced before? Write it to me! TIA

  Read the article

• ExpressCache not working after Windows 8 reinstall on Samsung Series 7 Gamer

  - by Morven

  I have a Samsung Series 7 Gamer laptop which came with Windows 8. After doing a reinstall of Windows, the ExpressCache software is no longer caching. Running "eccmd -info" shows me that the software is present and it has the MSATA drive partition configured. However, it's not actually caching anything. These are the results after having the system booted for days: C:\windows\system32eccmd -info ExpressCache Command Version 1.0.94.0 Copyright¬ 2010-2012 Condusiv Technologies. Date Time: 11/3/2013 12:26:20:263 (JAMETHIEL #36) EC Cache Info ================================================== Mounted : Yes Partition Size : 7.46 GB Reserved Size : 3.00 MB Volume Size : 7.46 GB Total Used Size : 86.50 MB Total Free Space : 7.38 GB Used Data Size : 16.63 MB Used Data Size on Disk : 84.38 MB Tiered Cache Stats ================================================== Memory in use : 32.00 MB Blocks in use : 136 Read Percent : 0.02% Cache Stats ================================================== Cache Volume Drive Number : 1 Total Read Count : 97242 Total Read Size : 4.13 GB Total Cache Read Count : 0 Total Cache Read Size : 595.50 KB Total Write Count : 161546 Total Write Size : 5.89 GB Total Cache Write Count : 0 Total Cache Write Size : 0 Bytes Cache Read Percent : 0.01% Cache Write Percent : 0.00% As you can see on the last two lines, cache read and write percent is nigh on zero. Anyone know where to look next? The only guides I can find deal with ExpressCache not being present or not having a configured drive.

  Read the article

• Scaling databases with cheap SSD hard drives

  - by Dennis Kashkin

  Hey guys! I hope that many of you are working with high traffic database-driven websites, and chances are that your main scalability issues are in the database. I noticed a couple of things lately: Most large databases require a team of DBAs in order to scale. They constantly struggle with limitations of hard drives and end up with very expensive solutions (SANs or large RAIDs, frequent maintenance windows for defragging and repartitioning, etc.) The actual annual cost of maintaining such databases is in $100K-$1M range which is too steep for me :) Finally, we got several companies like Intel, Samsung, FusionIO, etc. that just started selling extremely fast yet affordable SSD hard drives based on SLC Flash technology. These drives are 100 times faster in random read/writes than the best spinning hard drives on the market (up to 50,000 random writes per second). Their seek time is pretty much zero, so the cost of random I/O is the same as sequential I/O, which is awesome for databases. These SSD drives cost around $10-$20 per gigabyte, and they are relatively small (64GB). So, there seems to be an opportunity to avoid the HUGE costs of scaling databases the traditional way by simply building a big enough RAID 5 array of SSD drives (which would cost only a few thousand dollars). Then we don't care if the database file is fragmented, and we can afford 100 times more disk writes per second without having to spread the database across 100 spindles. . Is anybody else interested in this? I've been testing a few SSD drives and can share my results. If anybody on this site has already solved their I/O bottleneck with SSDs, I would love to hear your war stories! PS. I know that there are plenty of expensive solutions out there that help with scalability, for example the time proven RAM-based SANs. I want to be clear that even $50K is too expensive for my project. I have to find a solution that costs no more than $10K and does not take much time to implement.

  Read the article

• Not able to access external Hard disk

  - by Jash Jacob

  I have a 1TB External Hard drive which I'm currently not able to access. When I open the External drive in Finder, It shows it's empty. When I use the option to "Get Info", I get the dialog box stating it has about 300GB Free. Tried to get into the External Drive using Terminal, I had no luck. Checking in Disk Utility, It showed that I have many number of files but ZERO folder. I tried to "repair disk", in the process the external Drive got unmounted in between the process. I checked this drive on Windows. I was able to open almost all the folders but I wasn't able to copy anything onto the external drive. One folder caused my windows computer to hang, So i connected the drive back onto my MacBook Pro and tried to access the drive through terminal (this time it worked!) and then I tried to delete the folder with rm command, I got an "input/output error" What should i do to recover the files in that folder? How can i access my external drive on my mac

  Read the article

• Sql Server 2005 Connection Unstable When Sharing Connection

  - by intermension

  When connecting to a customers hosting service via Sql Server Management Studio on an internet connection that also has other activity on it, the Sql Server connection to the hosting service is often dropped. An obvious work around to this problem is to NOT have additional traffic on the connection but it still begs the question "Why the Sql Server connection is so unstable?". If there is, for arguments sake, 100kb of bandwidth and a couple of downloads running that are being serviced at 35kB each then there is 30kB bandwidth spare capacity. If a 3rd download is started, that can be serviced at 35kB by the server, it will top out at 30kB and leave zero spare capacity. This is fine and all downloads get along nicely. However it seems that with Sql Server connections it doesn't matter if there is spare bandwidth. Sql Server regularly times out if there is any additional activity on the connection even if i have 1024kB spare bandwidth capacity. This has been experienced across different customer hosting providers over the years and so the assumption is that it's Sql Server related. Why does Sql Server (apparently) require exclusive access to the internet connection in order to maintain a connection... even if that connection has plenty of spare capacity over and above any additional activity on the connection?

  Read the article

• How Do I Stop NFS Clients from Using All of the NFS Server's Resources?

  - by Ken S.

  I have a v4 NFS server running on Ubuntu 12.04LTS. It is the main repository for the web assets that four external nginx webservers mount to serve up to site visitors. These client servers connect to it via a read-only mount. Each of these RO servers has this displayed when I check the mounts: 10.0.0.90:/assets on /var/www/assets type nfs4 (ro,addr=10.0.0.90,clientaddr=0.0.0.0) The NFS master's /etc/exports file contains entries like this for each server: /mnt/lvm-ext4 10.0.0.40(ro,fsid=0,insecure,no_subtree_check,async) The problem that I'm seeing is that these clients are eventually utilizing all the RAM on the NFS server and causing it to crash. If I do a watch free -m I can watch the used memory creep up until it's used and then see the free buffers/cache entry creep down to near zero before the server eventually locks up requiring a reboot. There is some sort of memory leak somewhere that is causing this, and the optimal solution would be to find it and fix it, but in the meantime I need to find a way to have the NFS server protect itself from connected clients using all it's RAM. There must be some sort of setting that limits the resources the clients can use, but I can't seem to find it. I've tried adjusting the values for rsize and wsize but they don't seem to help or be related. Thanks for any tips.

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Using NFS for scalable PHP/MySQL web application

  - by Jeroen Moons

  Here's the situation: I have a PHP/MySQL web application that accepts user uploads (pdf files). From these pdf files' pages a preview image is made on the fly and presented to the web app's users. Some pdfs might be on the large side, most will be under 50 MB but some extreme cases could be as large as a few hundred MB. A little waiting for the preview image for large pdf files is acceptable but no more than a minute let's say. Everything is running on one server for now, but soon the app will hit the server's limit on both storage and processing power. My idea to solve the problem: To deal with this situation I had the idea of having one or more pdf processing servers as needed, and one or more file storage servers. These two types of servers are mounted to the server on which the actual app runs using NFS. The app could then use GearMan to delegate pdf processing tasks to these processing servers. The processing server can mount the storage server and read the file stored there, process it and write its output to that server. The servers I'm talking about will be amazon ec2 instances. The web app returns a link to the resulting pdf preview image on the storage server that was used which can then be used on the front end to show the image to the user. My question: I have zero experience with apps that use multiple servers, is this idea viable or is there a better way to do it? Is an NFS setup fast and reliable enough for this situation?

  Read the article

• OpenLDAP ACLs are not working

  - by Dr I

  First things first, I'm currently working with an OpenLDAP: slapd 2.4.36 on a Fedora release 19 (Schrödinger’s Cat). I've just install the openldap with yum and my configuration is the following one: ##### OpenLDAP Default configuration ##### # ##### OpenLDAP CORE CONFIGURATION ##### include /etc/openldap/schema/core.schema include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema pidfile /var/lib/ldap/slapd.pid loglevel trace ##### Default Schema ##### database mdb directory /var/lib/ldap/ maxsize 1073741824 suffix "dc=domain,dc=tld" rootdn "cn=root,dc=domain,dc=tld" rootpw {SSHA}SECRETP@SSWORD ##### Default ACL ##### access to attrs=userpassword by self write by group.exact="cn=administrators,ou=builtin,ou=groups,dc=domain,dc=tld" write by anonymous auth by * none I launch my OpenLDAP service using: /usr/sbin/slapd -u ldap -h ldapi:/// ldap:/// -f /etc/openldap/slapd.conf As you can see it's a pretty simple ACL which aim to allow access to the userPassword attribute to a specific group read only, then to the owner read and write to anonymous requiring auth and refuse the access to everyone else. The problem is: Even using a valid user with correct password my ldapsearch ends with zero informations retrieved from the directory, plus I've got a strange response on the result line. # search result search: 2 result: 32 No such object # numResponses: 1 here is the ldapsearch request: ldapsearch -H ldap.domain.tld -W -b dc=domain,dc=tld -s sub -D cn=user,ou=service,ou=employees,ou=users,dc=domain,dc=tld I did not specify any filter as I want to check that ldapsearch is correctly printing only allowed attribute.

  Read the article

• How can I make sound over hdmi in kubuntu work?

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :)

  Read the article

• Move every 3 rows into a column in excel

  - by Eliane El Asmr

  Please i need your help. I need to move every 3 rows into a new colomn. --Let's suppose i have this: Ambassade de France S.E. M. Patrice PAOLI 01-420000-420150 Ambassade de France Mme. Jamilé Anan 01-420000-420150 Ambassade de France Mme . Marie Maamari 01-420000-420150 --I need them to be Like this: Ambassade de France S.E. M. Patrice PAOLI 01-420000-420150 Ambassade de France Mme. Jamilé Anan 01-420000-420150 Ambassade de France Mme . Marie Maamari 01-420000-420150 I have this code. Can you help me Please. It's giving me error. Out of range. What should i change? It's urgent:(the code is for every 7, i need for every 3) Sub Every7() Dim i As Integer, j As Integer, cl As Range Dim myarray(100, 6) As Integer 'I don't know what your data is. Mine is integer data 'Change 100 to however many rows you have in your original data, divided by seven, round up 'remember arrays start at zero, so 6 really is 7 If MsgBox("Is your entire data selected?", vbYesNo, "Data selected?") <> vbYes Then MsgBox ("First select all your data") End If 'Read data into array For Each cl In Selection.Cells Debug.Print cl.Value myarray(i, j) = cl.Value If j = 6 Then i = i + 1 j = 0 Else j = j + 1 End If Next 'Now paste the array for your data into a new worksheet Worksheets.Add Range(Cells(1, 1), Cells(101, 7)) = myarray End Sub Thank you.

  Read the article

• ATI firepro will not detect a second DVI-D monitor

  - by John

  OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

  Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >