Search Results

Search found 8706 results on 349 pages for 'dual monitor'.

Page 87/349 | < Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >

  • A duplicate name has been detected on the TCP network

    - by MSedm
    When I installed my domain controller and DNS, I had 2 NIC on the server. Both NIC has its own IP address. NICs are not teamed, they are seperate and ip address are in the same subnet. Both IP address are now registered in the DNS. i found them in Forward and reverse lookup zone. Everything working ok except the following error in the event log. "A duplicate name has been detected on the TCP network......" Now I have realized that this is because of the second NIC. My question is if i disable the second NIC, what happen to those DNS record assiciated with the second ip address? How do I remove all the DNS recored for the disabled NIC? There are A record, some record with the name (same as parent folder), PTR record and may be more. How do i disable second NIC and remove all the associated DNS recoreds? Please help.

    Read the article

  • Shrinking windows and recovery partitions on the samsung new series 9

    - by bobbaluba
    I just bought a samsung NP900X3C, and as I was going to install linux, I noticed the windows partitions and recovery partitions occupied a major portion of the disk. The disk is a 128 GB SSD, and I want to keep the windows partition in order to play some games once in a while, but the windows disk is already 45GB full (with no installed programs) and the recovery partition is 20GB. That leaves under 60 GB for linux, which is not optimal, since that is what I'm going to be using most of the time, and there would be no room for games on the windows partition. There are also two small partitions that I don't know what are doing, one 100mb at the start of the disk that I'm guessing is some kind of boot partition, and one 5GB, that is described as an OS/2 hidden C: drive What I'm wondering is: can i delete the recovery partition? What about the mystical 5gb partition? Here is what fdisk reports: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 128.0 GB, 128035676160 bytes 255 heads, 63 sectors/track, 15566 cylinders, total 250069680 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x83953ffc Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 198273023 99033088 7 HPFS/NTFS/exFAT /dev/sda3 198273024 207276031 4501504 84 OS/2 hidden C: drive /dev/sda4 207276032 250068991 21396480 27 Hidden NTFS WinRE

    Read the article

  • Monitor Web Browsing Habits of Networked Users

    - by Linus
    I've been tasked with generating dynamic, real-time (or as close to real-time as possible) reports on the web browsing habits of my users. Basically we need a way of charting the amount of time user X spends on website Y. The last stop on our network is a FreeBSD box that is currently generating netflow data. I've reviewed some netflow analyzers but none seem to meet our needs. Any tools or suggestions will be greatly appreciated.

    Read the article

  • how to monitor traffic at port 53 (DNS)

    - by Registered User
    I am a bit confused with the abundant tcpdump tutorials on internet. I am having a few of the virtual machines running on a virtualization server.Where I am debugging a problem.Port 53 is the one in problem. I have a bridged setup where out of 4 LAN cards on the machine in question one is active and it is xen-br0 I want to check if there is any request coming on port 53 on the server by other machines on LAN in question. I also want to see if the guest operating systems on LAN or any other machine is sending traffic at port 53.Due to abundant messages being generated via tcpdump I am finding it difficult to grep the output at desired port. So how can I use it if some one can give an example that would be helpful. Thanks in advance.

    Read the article

  • Monitor programs accessing my keyboard?

    - by Anti Earth
    As of a few days ago, my computer is behaving 'erratically'. When I am typing, my pointer will randomly move to another place in the text and start typing a semi-random string of characters. ("gvyfn" is common; It has typed this about 8 times whilst I composed all the text above) It often highlights part of or all the text and overwrites it. It sometimes goes into loops of pressing Control-alt-delete down, bringing up Windows 7 menu thing. It sometimes even messes with mouseclicks; they have unexpected results, like requesting admin priveledges from applications, instead of switching to their window. I believe this is because it is holding a alt-function key down. This behaviour happens periodically, in waves. It might subside for an hour, then continue to haunt me. I believe it to be a virus or malicious program. My anti-virus (Symantec) and multiply MS rootkit removers could not find anything suspicious. I've noticed that sometimes it re-maps keys, and types gibberish when I press certain keys (though no pattern is evident). I believe a malicious program has installed a keyhook on my computer. I'm wondering... - Is there a way to let me view which programs are emulating keystrokes? - Is there a way to view what keyboard hooks are installed? (I'm also at liberty to try any other techniques to remove this blasted thing. It is easily the most fustrating computer problem I've encountered). Thanks!

    Read the article

  • Ubuntu 9.04 and Windows 7

    - by Aakarshit
    I had Windows 7 and Vista installed on my laptop. When I installed Ubuntu 9.04 the GRUB for Windows 7 was erased and I can only see choices for Vista and Ubuntu in the boot menu. How do I overcome this problem?

    Read the article

  • Installing Windows 8 on SSD

    - by StoneFX
    I'm trying to install Windows 8 (CP) on a 2nd SSD that I have (the 1st SSD has Windows 7). I boot into the installation from a usb stick, select the SSD, and launch the installation. When the computer goes to reboot during the install process, it keeps going back into the usb stick or my Windows 7 installation. It never recognizes the installation on the 2nd SSD. Is there something I'm doing wrong?

    Read the article

  • Long term system health monitor

    - by user30336
    As an experienced user, I sometimes notice that things are not going well with my computer. For example, my backup drive recently started cycling up and down, so I guessed it was probably dying, and replaced it. I detected this with my ears. Windows did not seem to notice or care. There ought to be software that monitors overall system health by keeping track of things like this, so that unusual events or increasing error rates will not be shrugged off. Among other things: disk errors that are recovered, corrupt network packets (at above the baseline expected rate) and crashes of trusted programs are early warnings. Is there any software that tries to use this kind of monitoring to warn of impending trouble?

    Read the article

  • Automate Monitor string in different log files

    - by EVIA
    I have few log files in different servers and I want to check output in the end of those log files for e.g . success: 4000 failed: 200 These logs files are getting generated daily and I have to keep track of these numbers. If there is any way I can automate this option instead of going and checking these files and wasting so much of my time. I want to create some kind of script like Go to \serverA\C$\log_07_02_2012.txt and check this line Go to \serverB\C$\log_07_02_2012.txt and check some other line. .... and it should give me output from all of these...

    Read the article

  • Toshiba Satellite U500 - Totally Damaged LCD

    - by ivan
    I accidentally damaged my Toshiba Satellite U500 laptop which resulted in a totally unusable LCD. The LCD panel has some cracks on it, and I can only see black & white spots; the laptop frame became broken/bent to where I can partially see inside the PC; the accident disassembled the CD tray, and bent the keyboard frame (which now has a weird hump). The system is still working though. It responds to my inputs (eg, turning it on/off, typing my password @ Windows Login, etc). What I want to do now is to transfer all of my important data from that laptop to my external drive. But I don't know how since the LCD screen is unreadable. I know I can connect it to an external monitor or a TV (I have a Samsung 1080p TV) but I don't know how. What cable should I purchase to connect the TV? Which ports on the laptop and TV should I connect it to? Do I need press something while/after connecting it? Can I boot my laptop using the TV?

    Read the article

  • 85 Hz on old/new driver looks the same like 75 Hz on previous one?

    - by jon
    I have old philips 107T5 CRT and Nvidia graphics card. I used old Nvidia driver (but it wasn't 'legacy' one when I installed it) for few years but recently I decided to install other Linux distribution. I used 75 Hz refresh rate and 1024x768 resolution on my previous distribution. After I installed the new distribution I had to install a Nvidia driver so I downloaded one from the Nvidia site (this time only legacy supported my card so I downloaded legacy and installed it). It wasn't automatically updating xorg.conf but I had my previous xorg.conf copy and I used it. When I run X I could only choose 85 and 75 Hz, 85 was checked as default. And now what shocks me: that default 85 Hz looks identically like 75 Hz on previous driver looked (at least to me). I tried 75 Hz out of curiosity and it's too bright, hurts, etc. But on the previous driver 75 Hz wasn't hurting my eyes. Why is it different? It's the same number after all, so it should always give the same results, right? That's my first question. Second question: Is 85 Hz OK for that monitor model? Would it break it? I tried to find the optimal refresh rate for this model but couldn't find it.

    Read the article

  • CRT as 2nd monitor goes screwy after start up?

    - by rhys
    new install of 12.04 on an old dell with a radeon ATI RV516 video card with monitor out and s-video out. During boot up all is good. Both screens operate and look fine. Then just before the desktop appears the cCRT goes purple and is covered in heavy horizontal lines, but as i said during boot up it was fine and the resolution was fine. The main monitor, an lcd, operates normally. everything else works fine, it's just the picture on the CRT that is screwed up. I used the same monitor and CRT running 11.10 which worked fine any help would be appreciated and yes i am a newbie to ubuntu here is a vid showing the completely normal screens at reboot then the purple badness when the desktop loads ?? and don't laugh at the slow machine, it's old. http://www.youtube.com/my_videos_edit?ns=1&video_id=zfuh6lBMLnc

    Read the article

  • Lost the config of my monitor once I connected it to a KVM switch.

    - by jfmessier
    I used to have a monitor (Acer 20", AL2017) connected to the external video port of my laptop. Everything was great and I could get a rather high resolution available when setting it under Ubuntu (all versions). But since I connected it to a KVM, the monitor is no more recognized, and I cannot go beyond 1024x768. My video adapter is an Intel chipset 9xx from an older Pentium Core 2 Duo laptop. The same monitor, using another video chipset (Intel 82G33/G31 rev 02) is properly detected through the switch box. Looks to me like the video chipset is not the best, and I can live with this. I see that I have no xorg.conf, and I understand that I would need to generate one so I can then use it to force the available modes on the X system. How can I generate the xorg.conf file for my Intel video chip, so I can use it then ? Merci :-)

    Read the article

  • How can i monitor syslog messages in c# console app with TCP

    - by djerry
    Heya, In my application, i need to monitor all messages sent by syslog. I've tried with UDP, but after one message, i didn't respond anymore (no error, just no heads up anymore). And setting up a tcp server isn't really the solution either i think. Can anyone guide me to a solution where i can log messages form syslog with tcp (normally on port 514). Thanks in advance.

    Read the article

  • Stats/Monitor/Inspector for beanstalkd

    - by Tim Lytle
    Does anyone know of an app that can monitor a beanstalkd queue? I'm looking for something that shows stats on tubes and jobs, and allows you to inspect the details. I'm not really picky about language/platform, just want to know if there's something out there before I write my own.

    Read the article

  • monitor table in data base

    - by hatem gamil
    hi all i want to make a web site to act as a monitor to a certain table in data base or act as a listenter on that table eg lets say i have table employees i want to make a web page that listen to changes occurs on that table (all DML operations) whenever a record is inserted i want this page alert me that a "1 row is inserted in table employee",or updated i want to get an alert " row number xx is updated" and so on so what is the best practise to do so thnx

    Read the article

  • server health monitor

    - by arash
    hello i need to a server monitoring solution. the solution must be able to alert when a server goes down also i want, the solution be flexible to work with various servers for example it must be able to monitor servers like, webserver,application server, DB server and ... i want to know is any open source solution is available for me? thanks in advance

    Read the article

  • Custom Monitor Resolution not recognized by Java

    - by Angie
    My weird monitor's native resolution isn't recognized by Windows, so I have to set a custom resolution for it. The problem is that java doesn't recognize it since it's not on Win7's "approved" list, so full-screen mode gets "stuck". Netbeans comes out of full-screen fine, so there has to be a way around this. Anyone know it? This example reproduces the issue: package resolutionexample; import java.awt.Dimension; import java.awt.DisplayMode; import java.awt.GraphicsDevice; import java.awt.GraphicsEnvironment; import javax.swing.JFrame; import javax.swing.SwingUtilities; public class Main { public static void main(String[] args) { SwingUtilities.invokeLater(new Runnable(){ public void run() { GraphicsEnvironment ge = GraphicsEnvironment.getLocalGraphicsEnvironment(); GraphicsDevice gd = ge.getDefaultScreenDevice(); DisplayMode currentDM = gd.getDisplayMode(); boolean currentInAvailable = false; System.out.println("Available resolutions:"); for ( DisplayMode availDM : gd.getDisplayModes() ){ //System.out.println(availDM.getWidth() + "x" + availDM.getHeight()); if ( availDM.equals(currentDM) ){ currentInAvailable = true; } } System.out.println("Current resolution: " + currentDM.getWidth() + "x" + currentDM.getHeight() ); System.out.println("Current in available: " + currentInAvailable); JFrame frame = new JFrame("Resolution Bug Example"); frame.setVisible(true); frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE); if ( !gd.isFullScreenSupported() ){System.exit(0);} gd.setFullScreenWindow(frame); gd.setFullScreenWindow(null); } }); } } Output running 1680x1050 (the monitor's wonky native resolution): run: Available resolutions: Current resolution: 1680x1050 Current in available: false Exception in thread "AWT-EventQueue-0" java.lang.IllegalArgumentException: Invalid display mode at sun.awt.Win32GraphicsDevice.setDisplayMode(Win32GraphicsDevice.java:393) at sun.awt.Win32GraphicsDevice.setFullScreenWindow(Win32GraphicsDevice.java:329) at resolutionexample.Main$1.run(Main.java:43) at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:209) at java.awt.EventQueue.dispatchEvent(EventQueue.java:597) at java.awt.EventDispatchThread.pumpOneEventForFilters(EventDispatchThread.java:269) at java.awt.EventDispatchThread.pumpEventsForFilter(EventDispatchThread.java:184) at java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java:174) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:169) at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:161) at java.awt.EventDispatchThread.run(EventDispatchThread.java:122) BUILD SUCCESSFUL (total time: 2 seconds) Output if I set my resolution to 1024x768 before running: run: Available resolutions: Current resolution: 1024x768 Current in available: true BUILD SUCCESSFUL (total time: 2 seconds)

    Read the article

  • Monitor USB optical mouse activity for movement and call a program on Windows

    - by CheeseConQueso
    I'm essentially looking to monitor a USB port input for whatever happens when the optical mouse detects its own movement and turns itself on. These mice usually have a dim red light when in "standby" mode and then the red light becomes brighter once you start moving it around. I want to use Visual Basic or something else native to the Windows environment to open an exe file or play a wav sound or call a bat file when the mouse "wakes up". Any suggestions or pushes in the right direction are appreciated.

    Read the article

  • how do you monitor your lamp server?

    - by ajsie
    i wonder how one can monitor a lamp server (ubuntu) on production. are there any standard tools for this to watch the server performance/load in realtime via the browser? how mysql, linux, apache etc are doing... what is best practice regarding this? any tutorials would be great. thanks!

    Read the article

  • Monitor file disk activity programmatically (Windows)

    - by iulianchira
    In Windows 2008R2, in Resource Monitor in the Disk Acitivity section I can see the number of bytes read from/written into files. How can I do this in a programatic manner, prefferably using C# (or Win32 API)? I have looked into WMI and various performance counters, however I cannot figure out if there is something which suits my needs.

    Read the article

< Previous Page | 83 84 85 86 87 88 89 90 91 92 93 94  | Next Page >