Search Results

Search found 10842 results on 434 pages for 'sshd config'.

Page 88/434 | < Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >

  • Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

    - by Mark S. Rasmussen
    As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

    Read the article

  • IIS 7.5 Unable to write configuration file

    - by flumeware
    I have a fault regarding IIS 7.5 on Win Server 2008 R2, whenever I try to change any site bindings or start an application pool I get the error below: Filename: \\?\C:\Windows\system32\inetsrv\config\applicationHost.config Error: Cannot write configuration file the application pools run as network service. None of the sites that are running have been affected however their configuration cannot be changed UPDATED 05/10/2012 A reboot fixed this issue, however I am curious to know what caused it in the first place.

    Read the article

  • Allowing connections initiated from outside

    - by Mark S. Rasmussen
    I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

    Read the article

  • Mercurial set per user rights

    - by Kami
    I would like to set better user access to my mercurial repos trough the cgi web interface. This is my current hgweb.config : [web] contact = first.lastname description = HG Repos allow_push=user1,user2,user3 allow_read=user1,user2,user3 [paths] repo01 = /home/mercurial/repo01 repo02 = /home/mercurial/repo02 repo03 = /home/mercurial/repo03 repo04 = /home/mercurial/repo04 How to setup the following ? : user1 has only access (push/read) to repo01 and repo02 user2 has only access (read only) to repo01 and repo02 user3 has only access (read) to repo01 and repo02, (push/read) repo03 I've checked multiple mercurial config tutorials but nothing helped me so far.

    Read the article

  • Intermittently, IIS7 requests get stuck in WindowsAuthenticationModule

    - by rbeier
    Hi, We're running an IIS7 server hosting several dozen websites. Several of these websites are all part of the same legacy app we've developed. These sites all run the same code and run in the same app pool. Roughly once a month over the past few months, we've found that all requests for this app pool start hanging indefinitely. When this happens, we receive an alert and we recycle the app pool. After that, the sites start working again. This only ever affects this one app pool - never any others on the same server. A couple times, before recycling the pool, I've looked at the currently-executing requests in the worker process. They all show up as executing inside the WindowsAuthenticationModule. Which is strange, because the vast majority of the application does not require authentication. There is a small admin section which uses Windows auth... but all the other requests should be anonymous. Does anyone have any idea as to what might be causing this? There are several unusual things about the way these sites are set up. As I mentioned, they all run the same code - multiple sites point at the same physical directory. The only difference is the host header bindings. I'm not sure why there isn't just one site with all the host headers, but that's how it works. In several of these sites, the same physical directory is mapped at two levels - as the root of the site and again as an application within the site. So if a user goes to http://oursite.com/index.aspx, that maps to c:\files\oursite\index.aspx. If a user goes to http://oursite.com/foo/index.aspx, that also maps to c:\files\oursite\index.aspx. I think there is code which looks at the request URL and handles the two requests differently. This is strange because the same web.config ends up being interpreted as a site config file, and also as an application config file within the site. I don't know if this might be related to the authentication problem. If we can't find the cause, we're thinking of a few workarounds we could try: Move the admin section into a separate site, and give the client a new admin URL. Run that separate site in its own app pool. Then in the web.config shared by all the other sites, remove the WindowsAuthenticationModule. That way there should be no possibility of a hang within the WindowsAuthenticationModule. Try running all these sites in the classic pipeline instead of the integrated pipeline. They were working fine on our old IIS6 server... (If we get desperate) Set up a watchdog script which monitors the sites and auto-recycles the app pool when it detects that requests are getting stuck. What do you think? Thanks for your help, Richard

    Read the article

  • Hylafax / Capi4hylafax: faxgetty does not recognize number of lines

    - by Wrikken
    We've got a T.30 card, 30 working lines on it, but for some reason, if I add more then 30 faxes in the queue at any time (and we're busy enough at peak times that this happens a lot), faxgetty sends faxes to non-existent lines and they appear in the error queue as a 'busy' signal on the line, which results in a lot of failed faxes because the counter of max 3 tries increases rapidly. This is using faxgetty (USE_FAXGETTY="y" in /etc/default/hylafax). I've inherited this thing, so I'm not entirely sure how faxgetty is supposed to know the number of lines. However, if I alter the script to faxmodem (USE_FAXGETTY="n" in /etc/default/hylafax and manually enabling 30 modems), this behavior goes away (new faxes 'wait' for a line to be available before trying to send, so each try / fail is a valid one on a working line, majorly descreasing the amount of failed faxes. However, when researching this almost anyone talks about faxgetty being the preferred, more robust, method, and on top of that for some unexplained reason all FIFO's disappeared for some reason after several errorless hours with faxmodem, forcing a hylafax restart using faxgetty until we figured out why this faxmodem solution failed (which is another question, and somewhat out of scope here). Environment: Debian 2.6.26-2-amd64 capi4hylafax 1:01.03.00.99.svn.300-12 hylafax-client 2:4.4.4-10.1 hylafax-server 2:4.4.4-10.1 Config --hfaxd.conf-- LogFacility: daemon ServerTracing: 0x1ff --hyla.conf-- Host: localhost Verbose: No VRes: 196 TimeZone: local DialRules: "/etc/hylafax/dialrules.europe" --/etc/hylafax/config -- InternationalPrefix: 00 LongDistancePrefix: 0 AreaCode: 99999 CountryCode: 31 DialStringRules: "etc/dialrules.europe" ModemGroup: any:faxCAPI SendFaxCmd: "/usr/bin/wrapc2faxsend" --/etc/hylafax/config.faxCAPI -- SpoolDir: /var/spool/hylafax FaxRcvdCmd: /var/spool/hylafax/bin/faxrcvd PollRcvdCmd: /var/spool/hylafax/bin/pollrcvd FaxReceiveUser: uucp FaxReceiveGroup: dialout LogFile: /var/spool/hylafax/log/capi4hylafax #no, checking this log did not yield anything interesting LogTraceLevel: 4 LogFileMode: 0600 ModemGroup: any:faxCAPI #repeats of faxCAPI2 = faxCAPI30, with of course another devicename/local ident: { HylafaxDeviceName: faxCAPI RecvFileMode: 0600 FAXNumber: ****redacted**** LocalIdentifier: ****some-ident-per-device*** MaxConcurrentRecvs: 0 OutgoingController: 1 OutgoingMSN: SuppressMSN: 0 NumberPrefix: NumberPlusReplacer: "00" UseISDNFaxService: 0 RingingDuration: 0 { Controller: 1 AcceptSpeech: 0 UseDDI: 0 DDIOffset: DDILength: 0 IncomingDDIs: IncomingMSNs: AcceptGlobalCall: 1 } } So in short: How does faxgetty determine the number of lines available? (the man page isn't terribly revealing, and I can't find an appropriate setting in hylafax-config. And how can I get a capi4hylafax/hylafax setup which queues more faxes then lines are available correctly without immediately incrementing the fail count? We will not be receiving any faxes on this machine b.t.w. As I said, I've inherited this thing, so if there are important configuration options I'm not including, please let me know.

    Read the article

  • Why can't I get Apache2 mod_dumpio working under Lucid Lynx Ubuntu?

    - by bland328
    I'm trying to capture all of the traffic to and from an Apache2 web server for troubleshooting purposes, so I did the following to try to set mod_dumpio up properly: Used a2enmod to enable mod_dumpio Changed LogLevel to "debug" in apache2.config Added "DumpIOInput On", "DumpIOOutput On" and "DumpIOLogLevel debug" to apache2.config Issued "/etc/init.d/apache2 restart" to restart Apache Issued "apache2ctl -t -D DUMP_MODULES" to make sure mod_dumpio was loaded I'm watching /var/log/apache2/error.log, but not seeing much there, and certainly not a dump of all input and output. Can anyone help?

    Read the article

  • Lighttpd wont restart due to an fastcgi.server error

    - by Mint
    Here is what comes up when I try to restart lighttpd user:/# /etc/init.d/lighttpd restart Stopping web server: lighttpd. Starting web server: lighttpdDuplicate config variable in conditional 0 global: fastcgi.server 2010-02-13 22:08:30: (configfile.c.907) source: /etc/lighttpd/lighttpd.conf line: 179 pos: 1 parser failed somehow near here: (EOL) failed! Lighttpd restarts fine when I comment out fastcgi config lines.

    Read the article

  • Changing default datadirectory to one on a External NAS or add external share

    - by Hagbart Celine
    So I have been searching the web for days, looking for a solution to my problem. Now my only hope are you guys. I have installed Owncloud successfully on my Windows Server 2008R2. It all runs smoothly and I can connect without problems. So first checks are OK. Now I wanted to change the default data directory from my server to a shared folder on my NAS (Synology DS1813+, DSM 5.0-4493 Update 3). Tried following: changing the directory in config.php I changed the path in the config file from : "C:\inetpub\wwwroot\myfolder\data" to "\NASIP\cloud". by doing this the owncloud server only shows: Code: Select all Daten-Verzeichnis (\192.168.2.4\Cloud\data) ist ungültig Bitte stelle sicher, dass das Daten-Verzeichnis eine Datei namens ".ocdata" im Wurzelverzeichnis enthält. I also tried coping the files that were created in the local data storage, to the share on the NAS. No Luck. Now I tried it by mapping a network drive and using that in the config.php But still no luck. I get the same message with the missing .ocdata file. Now I tried the "External Storage APP" that comes with owncloud I thought that at least I could add the share as an external storage. But this also does not work. tried UNC, Mapped Drive Name (Z:) but nothing helped. So now I'm turning to you.. Does anyone have expirience with this kind of setup? Or can you even tell me how to make it work? (default or external storgae, I don't care anymore ) Using NAS (Synology DS1813+, DSM 5.0-4493 Update 3), Owncloud 7, Windows Server 2008 R2, IIS7 I got an answer on an other forum: The second option is how it should be done: 1. Put OC in maintenance mode 2. Mount (mapping in the windows world) your NAS directly to your OS 3. Copy the local data directory to the NAS mount 4. Ensure the permission is setup to give the web user access to the NAS mount 5. Update OC config.php with the new data path 6. Disable OC maintenance mode And this seems like the right way.. Ensure the permission is setup to give the web user access to the NAS mount I guess this is where I am not sure. What user is it exactly on my Server that is making the requests to the NAS? If the user is for example "IUSR" I can just create an account on my synology NAS and give him full access to my share? (But what is IUSRs password?) I have full root ssh access to my NAS, so if you can tell me what chmod or chown I need to use on my cloud folder...

    Read the article

  • Remove (or add) Entry in Indicator-Applet (Ubuntu/GNOME)

    - by Tim Lytle
    I can't seem to find a guide or reference on how to configure the 'indicator-applet' (aka MessagingMenu) that came about in the 9.04 release of Ubuntu. It's that little mail icon that lists messaging apps. I can find docs about what it should do, people complaining about how it works, references that the API changed in 9.10, but not much on how to change the configuration. The MessagingMenu design spec page says that the config file should be at $HOME/.config/indicators/messages/applications/, but there's nothing there on my install (9.10).

    Read the article

  • Intermittently, IIS7 requests get stuck in WindowsAuthenticationModule

    - by Richard Beier
    We're running an IIS7 server hosting several dozen websites. Several of these websites are all part of the same legacy app we've developed. These sites all run the same code and run in the same app pool. Roughly once a month over the past few months, we've found that all requests for this app pool start hanging indefinitely. When this happens, we receive an alert and we recycle the app pool. After that, the sites start working again. This only ever affects this one app pool - never any others on the same server. A couple times, before recycling the pool, I've looked at the currently-executing requests in the worker process. They all show up as executing inside the WindowsAuthenticationModule. Which is strange, because the vast majority of the application does not require authentication. There is a small admin section which uses Windows auth... but all the other requests should be anonymous. Does anyone have any idea as to what might be causing this? There are several unusual things about the way these sites are set up. As I mentioned, they all run the same code - multiple sites point at the same physical directory. The only difference is the host header bindings. I'm not sure why there isn't just one site with all the host headers, but that's how it works. In several of these sites, the same physical directory is mapped at two levels - as the root of the site and again as an application within the site. So if a user goes to http://oursite.com/index.aspx, that maps to c:\files\oursite\index.aspx. If a user goes to http://oursite.com/foo/index.aspx, that also maps to c:\files\oursite\index.aspx. I think there is code which looks at the request URL and handles the two requests differently. This is strange because the same web.config ends up being interpreted as a site config file, and also as an application config file within the site. I don't know if this might be related to the authentication problem. If we can't find the cause, we're thinking of a few workarounds we could try: Move the admin section into a separate site, and give the client a new admin URL. Run that separate site in its own app pool. Then in the web.config shared by all the other sites, remove the WindowsAuthenticationModule. That way there should be no possibility of a hang within the WindowsAuthenticationModule. Try running all these sites in the classic pipeline instead of the integrated pipeline. They were working fine on our old IIS6 server... (If we get desperate) Set up a watchdog script which monitors the sites and auto-recycles the app pool when it detects that requests are getting stuck. What do you think? Thanks for your help, Richard

    Read the article

  • lacp, cicso 3550, 3560, help with configuration

    - by Flamewires
    Hey all this is a repost from a question I asked on the cisco forums but never got a useful reply. Hey I'm trying to convert the FreeBSD servers at work to dual-gig lagg links from regular gigabit links. Our production servers are on a 3560. I have a small test environment on a 3550. I have achieved fail-over, but am having troubles achieving the speed increase. All servers are running gig intel (em) cards. The configs for the servers are: BSDServer: #!/bin/sh #bring up both interfaces ifconfig em0 up media 1000baseTX mediaopt full-duplex ifconfig em1 up media 1000baseTX mediaopt full-duplex #create the lagg interface ifconfig lagg0 create #set lagg0's protocol to lacp, add both cards to the interface, #and assign it em1's ip/netmask ifconfig lagg0 laggproto lacp laggport em0 laggport em1 ***.***.***.*** netmask 255.255.255.0 The switches are configured as follows: #clear out old junk no int Po1 default int range GigabitEthernet 0/15 - 16 # config ports interface range GigabitEthernet 0/15 - 16 description lagg-test switchport duplex full speed 1000 switchport access vlan 192 spanning-tree portfast channel-group 1 mode active channel-protocol lacp **** switchport trunk encapsulation dot1q **** no shutdown exit interface Port-channel 1 description lagginterface switchport access vlan 192 exit port-channel load-balance src-mac end obviously change 1000's to 100's and GigabitEthernet to FastEthernet for the 3550's config, as that switch has 100Mbit speed ports. With this config on the 3550, I get failover and 92Mbits/sec speed on both links, simultaneously, connecting to 2 hosts.(tested with iperf) Success. However this is only with the "switchport trunk encapsulation dot1q" line. First, I do not understand why I need this, I thought it was only for connecting switches. Is there some other setting which this turns on that is actually responsible for the speed increase? Second, This config does not work on the 3560. I get failover, but not the speed increase. Speeds drop from gig/sec to 500Mbit/sec when I make 2 simultaneous connections to the server with or without the encapsulation line. I should mention that both switches are using source-mac load balancing. In my test I am using Iperf. I have the server(lagg box) setup as the server(iperf -s), and the client computers are client(iperf -c server-ip-address), so the source mac(and IP) are different for both connections. Any ideas/corrections/questions would be helpful, as the gig switches are what I actually need the lagg links on. Ask if you need more information.

    Read the article

  • Create .gitconfig for chrooted users

    - by Vincent LITUR
    I have several chrooted users on my server, and I want to install git for specific users. I block at the command : git config --global user.name "user_name" I use this command connected as the user, and I got this error : error: could not lock config file /home/username/.gitconfig: Permission denied I tried to create the file from root, and then put chmod 755 and chown username .gitconfig, but I get the error. Is there a way to do this ? Edit : This question http://stackoverflow.com/questions/17908386/unable-to-create-gitconfig-file-for-user answers mine

    Read the article

  • Windows 2003 registry corrupt - endless reboot

    - by Jack
    Windows 2003 will run the loading screen then it stop with "Stop c000218 registry file failure or corrupt. The registry can not load the hive \systemroot\system32\config\security" then it start a count down about dumping the physical memory to disk and reboot itself again. I found Error starting Windows SBS 2003 - STOP: c0000218 but the config is different directory than mine. Is it the same step to try for recovery console?

    Read the article

  • SQL 2008 Report Manager not working

    - by Fatherjack
    I have a SQL 2008 developer edition with SSRS and the report manager is only available from the local machine. If I try to access it from any other machine I get challenged for my domain u/name and pwd 3 times and then the screen stays blank. I have made changes to some config files (originals copied out) in order to get a 3rd party application to run but that is now uninstalled and the config files are all back to vanilla (originals copied back in) I feel its something to do with authentication but am stuck ... any suggestions welcomed Jonathan

    Read the article

  • Can't install apache server, refuses to find

    - by Greg Dougherty
    I'm attempting to install Apache httpd-2.4.3. running $ ./configure --with-included-apr --with-pcre=/home/gregd/httpd-2.4.3/pcre --with-mod_alias --with-mod_include --with-mod_mime --with-mod_rewrite --with-mod_speling --with-mod_ss I get the following error: configure: error: Did not find pcre-config script at /home/gregd/httpd-2.4.3/pcre But the file pcre-config most certainly DOES exist in /home/gregd/httpd-2.4.3/pcre. So does configure. Installing on ubuntu. Any help would be greatly appreciated.

    Read the article

  • what i should do in order to build curl without error?

    - by hugemeow
    failed when i run ./buildconf the error information is as follows: [mirror@home curl]$ ls acinclude.m4 CMakeLists.txt GIT-INFO MacOSX-Framework packages TODO-RELEASE Android.mk configure.ac include Makefile.am perl vc6curl.dsw buildconf COPYING install-sh Makefile.dist README winbuild buildconf.bat CTestConfig.cmake lib Makefile.msvc.names RELEASE-NOTES CHANGES curl-config.in libcurl.pc.in maketgz sample.emacs CHANGES.0 curl-style.el log2changes.pl missing src CMake docs m4 mkinstalldirs tests [mirror@home curl]$ ./config [mirror@home curl]$ ./buildconf buildconf: autoconf version 2.63 (ok) buildconf: autom4te version 2.59 (ERROR: does not match autoconf version) [mirror@home curl]$ echo $? 1

    Read the article

  • SSH: Configure ssh_config to use specific key file for a specific server fingerprint

    - by Penthi
    I have a key based login for a server. The IP and DNS of the server can change, because it is hosted on Amazon. Is there a way to configure the ssh client config to use the specific key file for this server only, when the fingerprint of the server matches? In other words: Normaly servers are matched by IP or DNS in the ssh client config. I want to do this by fingerprint, becaus IP and DNS can change.

    Read the article

  • How to change physical path of virtual directory in IIS7

    - by Tomek
    When you have multiple websites and each of them maps the same physical path as virtual directory, how to quickly change the physical path of that virtual directory for all websites? Note: I don't want to do use IIS Manager. I tried changing the path (find and replace) in %SYSTEM%\system32\inetsrv\config\applicationHost.config, then restarted IIS, but the change hasn't taken effect. What am I missing?

    Read the article

  • Getting error while installing mod_wsgi in centos

    - by user825904
    I have reinstalled python with enable shared [root@master mod_wsgi-3.4]# make clean rm -rf .libs rm -f mod_wsgi.o mod_wsgi.la mod_wsgi.lo mod_wsgi.slo mod_wsgi.loT rm -f config.log config.status rm -rf autom4te.cache [root@master mod_wsgi-3.4]# LD_RUN_PATH=/usr/local/lib make apxs -c -I/usr/local/include/python2.7 -DNDEBUG mod_wsgi.c -L/usr/local/lib -L/usr/local/lib/python2.7/config -lpython2.7 -lpthread -ldl -lutil -lm /usr/lib64/apr-1/build/libtool --silent --mode=compile gcc -prefer-pic -O2 -g -pipe -Wall -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -Wformat-security -fno-strict-aliasing -DLINUX=2 -D_REENTRANT -D_GNU_SOURCE -pthread -I/usr/include/httpd -I/usr/include/apr-1 -I/usr/include/apr-1 -I/usr/local/include/python2.7 -DNDEBUG -c -o mod_wsgi.lo mod_wsgi.c && touch mod_wsgi.slo In file included from /usr/local/include/python2.7/Python.h:8, from mod_wsgi.c:142: /usr/local/include/python2.7/pyconfig.h:1161:1: warning: "_POSIX_C_SOURCE" redefined In file included from /usr/include/sys/types.h:26, from /usr/include/apr-1/apr-x86_64.h:127, from /usr/include/apr-1/apr.h:19, from /usr/include/httpd/ap_config.h:25, from /usr/include/httpd/httpd.h:43, from mod_wsgi.c:34: /usr/include/features.h:162:1: warning: this is the location of the previous definition In file included from /usr/local/include/python2.7/Python.h:8, from mod_wsgi.c:142: /usr/local/include/python2.7/pyconfig.h:1183:1: warning: "_XOPEN_SOURCE" redefined In file included from /usr/include/sys/types.h:26, from /usr/include/apr-1/apr-x86_64.h:127, from /usr/include/apr-1/apr.h:19, from /usr/include/httpd/ap_config.h:25, from /usr/include/httpd/httpd.h:43, from mod_wsgi.c:34: /usr/include/features.h:164:1: warning: this is the location of the previous definition mod_wsgi.c: In function ‘wsgi_server_group’: mod_wsgi.c:991: warning: unused variable ‘value’ mod_wsgi.c: In function ‘Log_isatty’: mod_wsgi.c:1665: warning: unused variable ‘result’ mod_wsgi.c: In function ‘Log_writelines’: mod_wsgi.c:1802: warning: unused variable ‘msg’ mod_wsgi.c: In function ‘Adapter_output’: mod_wsgi.c:3087: warning: unused variable ‘n’ mod_wsgi.c: In function ‘Adapter_file_wrapper’: mod_wsgi.c:4138: warning: unused variable ‘result’ mod_wsgi.c: In function ‘wsgi_python_term’: mod_wsgi.c:5850: warning: unused variable ‘tstate’ mod_wsgi.c:5849: warning: unused variable ‘interp’ mod_wsgi.c: In function ‘wsgi_python_child_init’: mod_wsgi.c:7050: warning: unused variable ‘l’ mod_wsgi.c:6948: warning: unused variable ‘interp’ mod_wsgi.c: In function ‘wsgi_add_import_script’: mod_wsgi.c:7701: warning: unused variable ‘error’ mod_wsgi.c: In function ‘wsgi_add_handler_script’: mod_wsgi.c:8179: warning: unused variable ‘dconfig’ mod_wsgi.c:8178: warning: unused variable ‘sconfig’ mod_wsgi.c: In function ‘wsgi_hook_handler’: mod_wsgi.c:9375: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9377: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9379: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9383: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9403: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9405: warning: suggest parentheses around assignment used as truth value mod_wsgi.c:9408: warning: suggest parentheses around assignment used as truth value mod_wsgi.c: In function ‘wsgi_daemon_worker’: mod_wsgi.c:10819: warning: unused variable ‘duration’ mod_wsgi.c:10818: warning: unused variable ‘start’ mod_wsgi.c: In function ‘wsgi_hook_daemon_handler’: mod_wsgi.c:13172: warning: unused variable ‘i’ mod_wsgi.c:13170: warning: unused variable ‘elts’ mod_wsgi.c:13169: warning: unused variable ‘head’ mod_wsgi.c: At top level: mod_wsgi.c:8142: warning: ‘wsgi_set_user_authoritative’ defined but not used mod_wsgi.c:15251: warning: ‘wsgi_hook_check_user_id’ defined but not used /usr/lib64/apr-1/build/libtool --silent --mode=link gcc -o mod_wsgi.la -rpath /usr/lib64/httpd/modules -module -avoid-version mod_wsgi.lo -L/usr/local/lib -L/usr/local/lib/python2.7/config -lpython2.7 -lpthread -ldl -lutil -lm

    Read the article

  • Can I compile mutt under cygwin?

    - by openist
    I've been trying to compile mutt under cygwin for a few days. I always get the message: "configure: error: no curses library found" I have all the curses + devel stuff installed + termpcap, which I heard might be related. I've tried re-installing, i've tried specifying the location on the configure command line, but i'm not sure i'm doing it right: "--with-curses=/usr/lib/libncurses.a --with-curses=/usr/lib/libncurses.dll.a --with-curses=/usr/include/ncurses" Here's my config.log: http://floatsolutions.net/docs/config.log Any ideas?

    Read the article

  • What configuration entries are changed through the graphical options interface?

    - by Shamaoke
    I use a localized version of Firefox whose options/preferences menu and about:config entries differ from the default English base distribution. When I'm discussing Firefox on international forums, it's hard to tell people what options I alter and what values I use, since the localized names are different. Is there an exhaustive list of the about:config entries that can be changed from the graphical preferences/options dialog; something I can use as a reference for translating my localized names?

    Read the article

  • Postfix configuration (relay access)

    - by jome
    I have just installed POSTFIX on a Debian box, I pointed the relay host config setting to an exchange server which will deliver the mail to external users. So what I am trying to do is telnet to the debian box and send an email to [email protected] which will then be past to the exchange server for delivery. The problem is I get the following: rcpt to:[email protected] 554 relay access denied I have seen a section in the config "mydestination" but i want the exchange server to decide which domains it will deliver for and not the POSTFIX server.

    Read the article

  • check_client_access and RBLs

    - by Laurent
    In an attempt to better fight spam, I've configured Postfix like this: smtpd_client_restrictions = check_client_access hash:/etc/postfix/client_whitelist reject_unknown_client smtpd_recipient_restrictions = permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination reject_non_fqdn_sender, reject_non_fqdn_recipient, reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_destination, reject_unauth_pipelining, reject_invalid_hostname, reject_rbl_client zen.spamhaus.org, reject_rbl_client bl.spamcop.net, reject_rbl_client l2.apews.org, permit This config has reduced a lot of spam, and with the whitelist I was able to deal with some misconfigured but legitimate servers in order to accept them. However, I'm wondering if this particular whitelisting config will be able to do the job if some other legitimate servers found themselves blacklisted in one of these RBLs. Am I missing something?

    Read the article

< Previous Page | 84 85 86 87 88 89 90 91 92 93 94 95  | Next Page >