Search Results

Search found 6499 results on 260 pages for 'drop shadow'.

Page 89/260 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

  • Cooling for a small server room

    - by John Zwinck
    I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

    Read the article

  • Internet slowed down because of SQUID Server setup

    - by Ranjith Kumar
    Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

    Read the article

  • debian VM refusing all traffic apart from http

    - by james lewis
    I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

    Read the article

  • .NET Framework 1.1 on IIS 7

    - by Zack Peterson
    I have inherited a .NET Framework 1.1 web site that I must host with IIS 7 on Windows Server 2008. I'm having some trouble. 1. Installation I installed .NET Framework 1.1 following these instructions. The installation automatically created a new Application Pool "ASP.NET 1.1". I use that. 2. Trouble When I launch the web site I see web.config runtime errors: The tag contains an invalid value for the 'culture' attribute. I fix that one and then see: Child nodes are not allowed. I don't want to keep playing this whack-a-mole game. Something must be wrong. 3. Am I sure this is .NET 1.1? I examine the automatically created application pool. I see that it's 1.1. Advanced Settings... Basic Settings... This doesn't seem right. While 1.1 is set, it's not an option in the Advanced drop down selectors. And why in the Basic box is it just "v1.1" and not ".NET Framework v1.1.4322"? That would be more consistent. 4. I cannot create other .NET 1.1 App Pools I cannot select .NET Framework 1.1 for other application pools. It's not an option in the drop down selectors. What's up with that? What now? Why isn't v1.1 an option for all AppPools? How can I verify my application is in fact using .NET Framework 1.1? Why might I get these runtime errors?

    Read the article

  • How do you use a Mac without a mouse?

    - by NitroxDM
    So I was using my Mac Mini and decided to set the application button on Logic Click mouse to open Exposé. I had this set up at one time and found it useful. So I open the Exposé control panel and took a look at the triggers for Exposé. There is drop down for a secondary trigger. In that drop down there was a ton of mouse buttons 100+. So I selected #32 just to see what button #32 was on my 5 button mouse. Turns out it's all of them! So no matter what button I press guess what happens... I get Exposé. So using the just the keyboard how do I: Change the Exposé trigger? I can use the keyboard to bring up the control Exposé panel but guess what I can't get anything else to come in to focus. Kill Exposé? Right now I can say is D'oh! Any ideas?

    Read the article

  • How to crop Screen Recordings under Snow Leopard?

    - by willc2
    Quicktime Player for Snow Leopard now allows you record the screen. Awesome! Once you have a movie it will let you trim screen recordings for length. Is there a way to crop the movie's dimensions, either in QT or using some built-in or free software? Update: How to crop to an arbitrary size and aspect ratio? iMovie only seems to let you crop to the aspect ratio of the containing project. Result: Both good answers but since I have QuickTime Player 7 and Photoshop, that's the workflow I choose as the answer. NOTE: If you have Photoshop Extended, you can import a movie, use the crop tool, and Export the cropped movie. Not free or built-in, but convenient. To summarize the instructions from the video link ricbax posted: Open movie in QuickTime Player 7 Copy a frame and Paste it into a new document in Photoshop Draw a rectangular selection around the area to keep and fill with black Invert the selection and fill with white Save as .GIF, with 2 colors Back in QuickTime Player 7, open Movie Properties window Select the Video Track Select the Visual Settings Tab Drag and Drop the 2-color .GIF file onto the Mask drop area (or use choose file button) Export the (now cropped) movie DONE

    Read the article

  • Simulated NAT Traversal on Virtual Box

    - by Sumit Arora
    I have installed virtual box ( with Two virtual Adapters(NAT-type)) - Host (Ubuntu -10.10) - Guest-Opensuse-11.4 . Objective : Trying to simulate all four types of NAT as defined here : https://wiki.asterisk.org/wiki/display/TOP/NAT+Traversal+Testing Simulating the various kinds of NATs can be done using Linux iptables. In these examples, eth0 is the private network and eth1 is the public network. Full-cone iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to-source iptables -t nat -A PREROUTING -i eth0 -j DNAT --to-destination Restricted cone iptables -t nat POSTROUTING -o eth1 -p tcp -j SNAT --to-source iptables -t nat POSTROUTING -o eth1 -p udp -j SNAT --to-source iptables -t nat PREROUTING -i eth1 -p tcp -j DNAT --to-destination iptables -t nat PREROUTING -i eth1 -p udp -j DNAT --to-destination iptables -A INPUT -i eth1 -p tcp -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -i eth1 -p udp -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -i eth1 -p tcp -m state --state NEW -j DROP iptables -A INPUT -i eth1 -p udp -m state --state NEW -j DROP Port-restricted cone iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to-source Symmentric echo "1" /proc/sys/net/ipv4/ip_forward iptables --flush iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE --random iptables -A FORWARD -i eth1 -o eth0 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT What I did : OpenSuse guest with Two Virtual adapters - eth0 and eth1 -- eth1 with address 10.0.3.15 /eth1:1 as 10.0.3.16 -- eth0 with address 10.0.2.15 now running stund(http://sourceforge.net/projects/stun/) client/server : Server eKimchi@linux-6j9k:~/sw/stun/stund ./server -v -h 10.0.3.15 -a 10.0.3.16 Client eKimchi@linux-6j9k:~/sw/stun/stund ./client -v 10.0.3.15 -i 10.0.2.15 On all Four Cases It is giving same results : test I = 1 test II = 1 test III = 1 test I(2) = 1 is nat = 0 mapped IP same = 1 hairpin = 1 preserver port = 1 Primary: Open Return value is 0x000001 Q-1 :Please let me know If any has ever done, It should behave like NAT as per description but nowhere it working as a NAT. Q-2: How NAT Implemented in Home routers (Usually Port Restricted), but those also pre-configured iptables rules and tuned Linux

    Read the article

  • Can I disable this Windows (XP) Security Warning?

    - by FumbleFingers
    I recently reformatted my hard drive and reinstalled Windows XP (I know I'll have to take the plunge and commit to Win8 "real soon, now", but I'm just not quite ready for the upheaval yet! :) I used to use WinRar (and later, when I got fed up with the "nag" messages, 7-Zip), but I haven't installed either of them in my new configuration, so I must be using the built-in XP facility when I open *.zip files. For years, I've been opening downloaded *.zip archives, and using "drag & drop" to copy to a File Explorer window open on the folder where I want the files to end up (usually, My Documents\Downloads). But now I find that when I "drop" the file(s), I get a pop-up Windows Security Warning saying Are you sure you want to copy or move files to this folder? You should only move or copy files from locations that you trust Can anyone explain why I'm getting this message, and is there any (reasonably easy, please! :) way to suppress it? Since I've already put the *.zip file on my computer, it seems a bit late to ask if I trust it. (Thus far, the files in question have always been plain text, so it's not a matter of dodgy programs, etc.) Apologies for the low quality image - I don't have the appropriate tools or knowledge to do any better, and it doesn't help that my "PrtScr" screen capture has included what would have been on my second monitor (TV) if it had been turned on. If you can't read it, trust me - I have copied the text verbatim.

    Read the article

  • How to disable mod_security2 rule (false positive) for one domain on centos 5

    - by nicholas.alipaz
    Hi I have mod_security enabled on a centos5 server and one of the rules is keeping a user from posting some text on a form. The text is legitimate but it has the words 'create' and an html <table> tag later in it so it is causing a false positive. The error I am receiving is below: [Sun Apr 25 20:36:53 2010] [error] [client 76.171.171.xxx] ModSecurity: Access denied with code 500 (phase 2). Pattern match "((alter|create|drop)[[:space:]]+(column|database|procedure|table)|delete[[:space:]]+from|update.+set.+=)" at ARGS:body. [file "/usr/local/apache/conf/modsec2.user.conf"] [line "352"] [id "300015"] [rev "1"] [msg "Generic SQL injection protection"] [severity "CRITICAL"] [hostname "www.mysite.com"] [uri "/node/181/edit"] [unique_id "@TaVDEWnlusAABQv9@oAAAAD"] and here is /usr/local/apache/conf/modsec2.user.conf (line 352) #Generic SQL sigs SecRule ARGS "((alter|create|drop)[[:space:]]+(column|database|procedure|table)|delete[[:space:]]+from|update.+set.+=)" "id:1,rev:1,severity:2,msg:'Generic SQL injection protection'" The questions I have are: What should I do to "whitelist" or allow this rule to get through? What file do I create and where? How should I alter this rule? Can I set it to only be allowed for the one domain, since it is the only one having the issue on this dedicated server or is there a better way to exclude table tags perhaps? Thanks guys

    Read the article

  • Fail2Ban adds iptable rules but they are not working?

    - by EApubs
    Fail2Ban just blocked my IP for 3 SSH attempts. It added the iptables rule and I can see it using the "sudo iptables -L -n" command. But I can still access the site and login through SSH! What might be the problem? Is it because im using CloudFlare? I have set Nginx to write the real IPs to the access logs instead of the Cloud Flare IP. Isn't it enough? Chain fail2ban-ssh (1 references) target prot opt source destination DROP all -- 119.235.14.8 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 The input chain : Chain INPUT (policy DROP) target prot opt source destination fail2ban-NoAuthFailures tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 fail2ban-nginx-dos tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,8090 fail2ban-postfix tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 25,465 fail2ban-ssh-ddos tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 ufw-before-logging-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-logging-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-reject-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-track-input all -- 0.0.0.0/0 0.0.0.0/0 LOG all -- 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 4

    Read the article

  • Unexplained cache RAM drops on Linux machine

    - by FunkyChicken
    I run a CentOS 5.7 64 machine with 24gb ram and running kernel 2.6.18-274.12.1.el5. This machine runs only Nginx, php-fpm and Xcache as extra applications. Since about 3 weeks my memory behavior on this machine has changed and I cannot explain why. There are no crons running which flush anything like this. There are also no large numbers of files being deleted/changed during these drops. The 'cached' memory gets dropped about every few hours, but it's never a set gap between flushes, this indicates to me that some bottleneck gets reached instead. It also always seems to be when total memory usages gets to about 18GB, but again, not always exactly 18GB. This is a graph of my memory usage: As you can see in the graph the 'buffers' always stay more or less the same, it is mainly the 'cache' that gets dropped. Running vmstat -m I have outputted the memory usage just before and just after a memory drop. The output is here: http://pastebin.com/diff.php?i=hJqZqztm 'old version' being before, 'new version' being after a drop. About 3 weeks ago my server crashed during a heavy DDOS attack, after I rebooted the machine this odd behavior started. I have checked a bunch of logs, restarted the machine again, and cannot find any indication what changed. During these 'cache' memory drops, my iNode usage drops at the same time. Does anyone have any idea what might be causing this behavior? Clearly my RAM isn't full, so I am curious why this could be happening.

    Read the article

  • fail2ban block ports rules iptable

    - by J Spen
    I just installed Ubuntu Server 14.04 and don't have much experience with IPtables. I am trying to get a basic setup going where I only accept SSH connections on port 22 and 2222. I actually have that working with no problem using fail2ban ssh. Then I wanted to block all other ports except 423 and 4242 but either method of DROPing all connections that are not listed seems not to work and it blocks me out of everything. Below is the setup that works: -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A fail2ban-ssh -j RETURN I tried to change it either to: -P INPUT DROP -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A fail2ban-ssh -j RETURN or: -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -N fail2ban-ssh -A INPUT -p tcp -m multiport --dports 22,2222 -j fail2ban-ssh -A INPUT -j DROP -A fail2ban-ssh -j RETURN I have noticed that the rules for fail2ban-ssh are automatically added to my iptables on boot because if I save them with iptables-persistant they are entered twice. How do I go about blocking everything accept those 2 ports using fail2ban? Is it a bad fail2ban configuration or do I need to add the fail2ban-ssh -j Return somewhere else in my code.

    Read the article

  • Internet Troubles - PPPoE vs PPPoA?

    - by AkkA
    I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

    Read the article

  • Are my iptables secure?

    - by Patricia
    I have this in my rc.local on my new Ubuntu server: iptables -F iptables -A INPUT -i eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 9418 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 9418 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 5000 -m state --state NEW,ESTABLISHED -j ACCEPT # Heroku iptables -A INPUT -i eth0 -p tcp --sport 5000 -m state --state ESTABLISHED -j ACCEPT # Heroku iptables -A INPUT -p udp -s 74.207.242.5/32 --source-port 53 -d 0/0 --destination-port 1024:65535 -j ACCEPT iptables -A INPUT -p udp -s 74.207.241.5/32 --source-port 53 -d 0/0 --destination-port 1024:65535 -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT iptables -P INPUT DROP iptables -P FORWARD DROP 9418 is Git's port. 5000 is a port used to manage Heroku apps. And 74.207.242.5 and 74.207.241.5 are our DNS servers. Do you think that this is secure? Can you see any holes here? Update: Why is it important to block OUTPUT? This machine will be used only by me.

    Read the article

  • Blocking HTTPS and P2P Traffic

    - by Genboy
    I have a Debian server running at the gateway level on a LAN. This runs squid for creating block lists of websites - for eg. blocking social networking on the LAN. Also uses iptables. I am able to do a lot of things with squid & iptables, but a few things seem difficult to achieve. 1) If I block facebook through their http url, people can still access https://www.facebook.com because squid doesn't go through https traffic by default. However, if the users set the gateway IP address as proxy on their web browser, then https is also blocked. So I can do one thing - using iptables drop all outgoing 443 traffic, so that people are forced to set proxy on their browser in order to browse any HTTPS traffic. However, is there a better solution for this. 2) As the number of blocked urls increase in squid, I am planning to integrate squidguard. However, the good squidguard lists are not free for commercial use. Anyone knows of a good squidguard list which is free. 3) Block yahoo messenger, gtalk etc. There are so many ports on which these Instant Messenger softwares work. You need to drop lots of outgoing ports in iptables. However, new ports get added, so you have to keep adding them. And even if your list of ports is current, people can still use the web version of gtalk etc. 4) Blocking P2P. Haven't been able to figure out how to do this till now.

    Read the article

  • Amazon EC2 instance missing Network Interface

    - by Sergiks
    I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

    Read the article

  • Blocking an IP in Webmin

    - by Dan J
    I've been checking my /var/log/secure log recently and have seen the same bot trying to brute force onto my Centos server running webmin. I created a chain + rule in Networking - Linux Firewall: Drop If source is 113.106.88.146 But I'm still seeing the attempted logins in the log: Jun 6 10:52:18 CentOS5 sshd[9711]: pam_unix(sshd:auth): check pass; user unknown Jun 6 10:52:18 CentOS5 sshd[9711]: pam_succeed_if(sshd:auth): error retrieving information about user larry Jun 6 10:52:19 CentOS5 sshd[9711]: Failed password for invalid user larry from 113.106.88.146 port 49328 ssh2 Here is the contents of /etc/sysconfig/iptables: # Generated by webmin *filter :banned-ips - [0:0] -A INPUT -p udp -m udp --dport ftp-data -j ACCEPT -A INPUT -p udp -m udp --dport ftp -j ACCEPT -A INPUT -p udp -m udp --dport domain -j ACCEPT -A INPUT -p tcp -m tcp --dport 20000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp --dport https -j ACCEPT -A INPUT -p tcp -m tcp --dport http -j ACCEPT -A INPUT -p tcp -m tcp --dport imaps -j ACCEPT -A INPUT -p tcp -m tcp --dport imap -j ACCEPT -A INPUT -p tcp -m tcp --dport pop3s -j ACCEPT -A INPUT -p tcp -m tcp --dport pop3 -j ACCEPT -A INPUT -p tcp -m tcp --dport ftp-data -j ACCEPT -A INPUT -p tcp -m tcp --dport ftp -j ACCEPT -A INPUT -p tcp -m tcp --dport domain -j ACCEPT -A INPUT -p tcp -m tcp --dport smtp -j ACCEPT -A INPUT -p tcp -m tcp --dport ssh -j ACCEPT -A banned-ips -s 113.106.88.146 -j DROP COMMIT # Completed # Generated by webmin *mangle :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed # Generated by webmin *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed

    Read the article

  • Router drops internet connection if I connect an additional pc

    - by BluePerry
    Hey, I'm using a SMC2804WBRP-G router connected to my ADSL-modem. Usually there are two computers connected to this router: a win7 ultimate desktop(wired) and a macbook air (wireless). Both working absolutely fine and never caused any connection drops as far as I know. A new room mate moved in last month and each time she starts up her win7 home laptop the router looses the internet connection. The laptop is on a wired connection. The first time she connected to my router, the connection dropped every 2 mins. To find out whats wrong with her machine I disabled all unnecessary services etc. besides the anti virus software. That helped to eliminate almost all of those periodic connection drops. But the start up drop remained and I've got the feeling that the router is still loosing connection from time to time. I haven't had the time to find out what service caused the periodic drops. But I'm more concerned about is that start up drop. Can anyone point me in the right direction to look for the problem? I would be very thankful for any hints or tips!

    Read the article

  • Internet Troubles - PPPoE vs PPPoA?

    - by AkkA
    I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

    Read the article

  • Document Map in MS Word 2007 going bonkers

    - by rzlines
    I'm working on a large project report in Microsoft Word 2007 and have been using the document map to generate the index. I have been carefully selecting the headers that need to be added to the document map but I saved the document and opened it up today to work on it - the document map has added whatever it pleases there. This is a temporary fix from a post that I found after extensive searching that works, but when I save and close the document and open it up again I face the same dilemma: I have noticed that when Word stuffs up the document map after opening the file, I can undo this by using the UNDO button. Word calls it ’Autoformat’. I have also fixed a file that has had the document map screwed permanently (i.e saved with it) by selecting all (CTRL+A),selecting the PARAGRAPH drop down menu in the HOME TAB and in the OUTLINE drop down box, selecting ’Body Text’. This removed all the problems and did not seem to affect my outline level paragraph headings. This is also another temporary fix but I have to be on my toes not to let Word auto format at the start of the document. I also can't afford to entirely turn off auto format as I need it. I’ve solved this problem for me. When you open the file, a progress bar at the bottom first says Opening (ESC to Cancel) and then it says Word is formatting the document (ESC to Cancel). If I cancel the second process, TOC fine. No cancelling, TOC screwed. Can anyone work out how to switch off the autoformatting? This is the post in which i found for the temporary fix

    Read the article

  • iptables firewall rules not allowing ssh from lan to DMZ

    - by ageis23
    Chain INPUT (policy ACCEPT) target prot opt source destination REJECT tcp -- anywhere anywhere tcp dpt:www reject-with tcp-reset REJECT tcp -- anywhere anywhere tcp dpt:telnet reject-with tcp-reset ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED DROP udp -- anywhere anywhere udp dpt:route DROP udp -- anywhere anywhere udp dpt:route ACCEPT udp -- anywhere anywhere udp dpt:route logdrop icmp -- anywhere anywhere logdrop igmp -- anywhere anywhere ACCEPT udp -- anywhere anywhere udp dpt:5060 ACCEPT 0 -- anywhere anywhere state NEW logaccept 0 -- anywhere anywhere state NEW ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere logdrop 0 -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT 0 -- 192.168.0.0/24 192.168.2.0/24 reject-with icmp-port-unreachable ACCEPT tcp -- choister 192.168.2.142 tcp dpt:ssh state NEW REJECT 0 -- 192.168.0.0/24 192.168.3.0/24 reject-with icmp-port-unreachable ACCEPT gre -- 192.168.1.0/24 anywhere ACCEPT tcp -- 192.168.1.0/24 anywhere tcp dpt:1723 ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU lan2wan 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED logaccept tcp -- anywhere choister tcp dpt:www TRIGGER 0 -- anywhere anywhere TRIGGER type:in match:0 relate:0 trigger_out 0 -- anywhere anywhere logaccept 0 -- anywhere anywhere state NEW logdrop 0 -- anywhere anywhere The ssh server I'm trying to connect to is in the DMZ(192.168.0.145). It's mainly used as a web server. I need access to it from my room 192.168.2.142. I don't get why ssh can't forward onto the 192.168.2.0 subnet? I'm sure it's the reject rule that causing this because it works without it.

    Read the article

  • RAID-capable 3.5" SATA Drives

    - by nroam
    I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

    Read the article

  • fail2ban iptable rule wont block

    - by Termiux
    So I set up fail2ban on my Debian 7 server, still I've been getting hit a lot and I dont know why is not blocking properly. The regex works, it recognizes the attempts but it seems the iptables rules it insert wont work, this is how it look iptables ouput looks after fail2ban tries to block. Chain INPUT (policy ACCEPT) num target prot opt source destination 1 fail2ban-courierauth tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 2 fail2ban-couriersmtp tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 3 sshguard all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination Chain fail2ban-courierauth (1 references) num target prot opt source destination 1 DROP all -- 216.x.y.z 0.0.0.0/0 2 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-courierimap (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-courierpop3 (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-couriersmtp (1 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-postfix (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-sasl (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 In the iptables above you can see the "Chain fail2ban-courierauth" rule that added the drop rule for the ip but Im still able to connect!! I can still connect to the server, why isn't it blocking?

    Read the article

  • Problems creating a functioning table

    - by Hoser
    This is a pretty simple SQL query I would assume, but I'm having problems getting it to work. if (object_id('#InfoTable')is not null) Begin Drop Table #InfoTable End create table #InfoTable (NameOfObject varchar(50), NameOfCounter varchar(50), SampledValue float(30), DayStamp datetime) insert into #InfoTable(NameOfObject, NameOfCounter, SampledValue, DayStamp) select vPerformanceRule.ObjectName AS NameOfObject, vPerformanceRule.CounterName AS NameOfCounter, Perf.vPerfRaw.SampleValue AS SampledValue, Perf.vPerfHourly.DateTime AS DayStamp from vPerformanceRule, vPerformanceRuleInstance, Perf.vPerfHourly, Perf.vPerfRaw where (ObjectName like 'Logical Disk' and CounterName like '% Free Space' AND SampleValue > 95 AND SampleValue < 100) order by DayStamp desc select NameOfObject, NameOfCounter, SampledValue, DayStamp from #InfoTable Drop Table #InfoTable I've tried various other forms of syntax, but no matter what I do, I get these error messages. Msg 207, Level 16, State 1, Line 10 Invalid column name 'NameOfObject'. Msg 207, Level 16, State 1, Line 10 Invalid column name 'NameOfCounter'. Msg 207, Level 16, State 1, Line 10 Invalid column name 'SampledValue'. Msg 207, Level 16, State 1, Line 10 Invalid column name 'DayStamp'. Msg 207, Level 16, State 1, Line 22 Invalid column name 'NameOfObject'. Msg 207, Level 16, State 1, Line 22 Invalid column name 'NameOfCounter'. Msg 207, Level 16, State 1, Line 22 Invalid column name 'SampledValue'. Msg 207, Level 16, State 1, Line 22 Invalid column name 'DayStamp'. Line 10 is the first 'insert into' line, and line 22 is the second select line. Any ideas?

    Read the article

  • Router intermittently failing

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

    Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >