Search Results

Search found 275 results on 11 pages for 'ahci'.

Page 9/11 | < Previous Page | 5 6 7 8 9 10 11  | Next Page >

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• Hard drive not correctly recognized on a new Windows 7 installation, but works correctly on Windows XP

  - by david

  I'm having problems configuring a hard disk in a brand new, clean Windows 7 installation. System specs: Hard disk: WD VelociRaptor WD6000HLHX (600 GB, 10000 RPM) Motherboard: Gigabyte Z77X-UD3H BIOS SATA mode set to AHCI (not RAID), with disk connected to SATA0 (6 Gb/s port). Windows 7 Enterprise SP1 64-bit The disk is recognized by the BIOS and is correctly identified, with the name and size correctly reported. Windows recognizes the disk itself and reports the device is functioning correctly, but it doesn't appear in Explorer. Disk Management shows the drive, but incorrectly states that it is uninitialized and has no partitions. If I try to initialize the drive, I get an error saying that "the system cannot find the file specified" (what file?). Before connecting the drive to the new machine, I partitioned and formatted it under Windows XP SP2, creating 2 partitions (MBR, not GPT) and copying over a boatload of data. However, none of this data appears under Windows 7. If I put the disk back into the Windows XP machine, I can access the disk and all of its data. Is it possible to get Windows 7 to correctly recognize the disk without having to erase it and start over? If so, how do I do so? I checked this question, which seems to cover the same issue, but it didn't help.

  Read the article

• SATA HDD stuttering on reads (LED on)

  - by jdehaan

  I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

  Read the article

• Ubuntu Device-mapper seems to be invincible!

  - by Andrew Bolster

  I'm working on a hopefully unrelated question question and I've got to a strange situation. First: I know very little about the very low level hardware kernal storage driver magix, so I'm hoping a) someone can help and b) someone can explain it to me better. I've been trying a dozen different configurations of my 2x500GB SATA drives over the past few hours involving switching between ACHI/IDE/RAID in my bios; After each attempt I've reset the bios option, booted into a live CD, deleting partitions and rewriting partition tables left on the drives. Now, however, I've been sitting with a /dev/mapper/nvidia_XXXXXXX1 that seems to be impossible to kill! its the only 'partition' that i see in the Ubuntu install (but I can see the others in parted) but it is only the size of one of the drives, and I know I did not set any RAID levels other than RAID0. Anyone have any ideas how I can kill this and get back to just two independent IDE drives? Or can anyone convince me of a reason to go the AHCI route? Many thanks in advance.

  Read the article

• Lenovo S110 netbook screen resolution Ubuntu

  - by Neigyl R. Noval

  I am still stuck with 800x600 resolution. Here is the output of lspci: 00:00.0 Host bridge: Intel Corporation Device 0bf2 (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Device 0be2 (rev 09) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01) Also, I tried modifying /usr/lib/X11/xorg.conf.d/10-monitor.conf to fix this problem, but still does not work: Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Screen0" Monitor "Monitor0" Device "Card0" SubSection "Display" Viewport 0 0 Depth 1 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 4 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 8 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 15 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" EndSubSection EndSection Section "Device" Identifier "Card0" Driver "vesa" VendorName "Intel Corporation Device" EndSection I'm using Gnome. System Preference Monitor screen resolution sticks to 800x600. What am I going to do?

  Read the article

• Wireless driver activation problem in compaq c700 in ubuntu 9.04

  - by Fazil

  I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

  Read the article

• FreeBSD ZFS RAID-Z2 performance issues

  - by Axel Gneiting

  I'm trying to build my own network attached storage based on FreeBSD+ZFS+standard components, but there are strange performance issues. The hardware specs are: AMD Athlon II X2 240e processor ASUS M4A78LT-M LE mainboard 2GiB Kingston ECC DDR3 (two sticks) Intel Pro/1000 CT PCIe network adapter 5x Western Digital Caviar Green 1.5TB I created a RAID-Z2 zpool from all disks. I installed FreeBSD 8.1 on that zpool following the tutorial. The SATA controllers are running in AHCI mode. Output of zpool status: pool: zroot state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM zroot ONLINE 0 0 0 raidz2 ONLINE 0 0 0 gptid/7ef815fc-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/80344432-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/81741ad9-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/824af5cb-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/82f98a65-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 The problem is that write performance on the pool is very very bad (<10 MB/s) and every application that is accessing the disk is unresponsive every few seconds when writing. It seems like writing is fine until the ZFS ark cache is full and then ZFS stalls the entire system I/O till it's finished writing that data. Also I'm getting kmem_malloc to small kernel panics. I've already tried to put vm.kmem_size="1500M" vm.kmem_size_max="1500M" into /boot/loader.conf, but it doesn't help. Does anyone know what's going on here? Am I really not having enough memory for ZFS to handle this RAID-Z2?

  Read the article

• SSD Drive not being recongized in BIOS

  - by chobo2

  Well I bought my first drive Mushkin Chronos 180GB and got it installed in my computer and loaded up. I went to windows 7 and initialized the drive and then I installed "SSDlife Free" and loaded it up and my the SSD drive came up said it was "powered on 3 times"(thought it was odd but then thought maybe some testing???). I then restarted my computer and loaded into Acronis. Went to my SSD drive and make a partition called windows(made a basic logical partition). I then loaded up Norton ghost and wanted to copy my current windows onto the SSD drive on the partition I made found out I could not do it through the recovery disk so I made a backup of my windows drive and wanted to then restore it onto the SSD drive. Came back an hour later when the backup was done. I tried to restore the it on my SSD drive and could not find the partition so I loaded up Acronis again and it did not see it. I then went to the bios and saw only my other hard drive. What I tried Tried uplugging and replugging in both sata and power cables. Tried using the power and sata cable from the working drive and giving it the ones that SSD drive were using. Tried Sata AHCI Mode (Intel ICH9 Southbridge) Tried SATA PORT0-1 NATIVE MODE (Intel ICH9 Southbridge) Nothing worked. Software / hardware Windows 7 ultimate Gigabyte S-Series GA-P35-DS3L Mother board I hope someone has some ideas on why it is not being recognized.

  Read the article

• bootmgr image is corrupt

  - by bacord

  I just replaced my HD with a SSD. I did a brand new install on the SSD and I received the following error after booting BOOTMGR image is corrupt. The system cannot boot. A little configuration for your knowledge. The system used to be a dual boot with XP & windows 7. After replacing the original startup HD with my SSD I changed a setting in the bios to AHCI (I have tested changing it back but this did not help). When I look at the stats on the drive in the bios, it claims that the SSD is in a raid configuration despite the settings not being configured that way. Related System Information: Intel 320 Series 80 GB Sata II SSD JetWay JPA78VM3-H-LF AM2+/AM2 AMD 780V HDMI Micro ATX AMD Motherboard AMD Athlon 64 X2 7 GB ram I have performed 2 fresh installs to no avail. Also, followed this guide and performed option 1 and 2. I have done bootsec/fixmbr and /fixboot. So.. any suggestions?

  Read the article

• Move an SSD with Windows 7 to a new PCIe SATA controller card

  - by Shevek

  This is my current setup: Abit AB9 QuadGT motherboard which has an Intel P965 chipset with Intel ICH8 SATA Rev. 2.0 controller Kingston HyperX 3K 120GB SSD which supports SATA Rev. 3.0 Windows 7 Ultimate x64 For some reason I was unable to install Windows with the controller set in AHCI mode, even with the correct driver from Intel so it is currently in IDE mode. Due to the ICH8 controller being SATA Rev 2.0 and running in IDE mode, the SSD is operating well under it's published read/write speeds. I have ordered an Asus U3S6 controller card to add both SATA Rev. 3.0 and USB 3.0 to my computer. The motherboard does have a PCIe x4 slot available so I will hopefully achieve the full potential of my SSD. My question is this - am I able to swap the SSD over to the controller card from the motherboard controller without having to clean install Windows? I am hoping that all I will need to do is ensure that the controller card drivers are available to Windows and set the registry as per this KB article. Will this work or should I perform a clean installation?

  Read the article

• Solid State Drive Occasionally Freezes For A Minute While OS Is "Beach Balling"

  - by Boris_yo

  Almost a month ago I bought Intel 330 128GB solid state drive, migrated my data with Intel branded limited-feature Acronis from old HDD to new SSD, optimized with Intel Toolbox and started using it. Occassionally I get close to 1 minute freezes while seeing operating system "beach balls" and animations still work, I can interact and click on something but nothing responds, nothing loads. Recently a couple of such freezes occurred in shorter amount of time in a row. I have noticed that if I stop interacting with laptop, the freeze lasts less time than if I was interacting with laptop. But the bigger problem is when freeze just does not end and computer keeps being stuck unlil it is more than half hour and I run out of patience to keep waiting and feeling I need to restart the system because I am not getting anywhere. Such freeze happened while laptop was cold booting into Windows 7. This is when freeze hang occurred and I had to restart, only later to be greeted with Windows recovery screen stating something about faiure of boot sector and asking to insert Windows repair CD. But after I restarted, Windows booted successfully and all was well. I have filmed video of freeze hang occurring in cold boot which you can see here (on video page look below for description): http://www.youtube.com/watch?v=8b7MQlcDTUs As I have mentioned in the beginning, the SSD is less than a month old but here is S.M.A.R.T statistics just in case (TRIM is enabled btw according to CrystalDiskInfo): I want to emphasize that this SSD is the only drive I have, yet it is working in RAID mode (it was enabled initially in BIOS by previous laptop's owner) on Intel Rapid Storage drivers. I am contemplating about switching to AHCI mode but want to be sure this won't cause data loss. Additionally, the stock firmware is the only firmware available currently, yet Intel does not respond to my posts in their community board. If anyone here has this SSD model or generally has experience with SSD drives, I would love to know your thoughts.

  Read the article

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Windows is very slow with my new SSD

  - by Maksym H.

  I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

  Read the article

• SSH Interactive mode not working

  - by Ekin Koc

  I have a Debian based linux server running for a year or so, without any problems. A couple of days ago, ssh interactive mode stopped working for no reason. I mean, I can open an ssh connection just fine, the server greets me with shell but I just can't type anything. However, if I send commands like this: ssh [email protected] cat /var/log/messages, I get the response. I dug through several logs and found one message, which feels remotely relevant to the problem; sh kernel: [10222733.062511] ------------[ cut here ]------------ sh kernel: [10222733.062522] WARNING: at /build/buildd-linux-2.6_2.6.32-39-amd64-7yVIH2/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/char/tty_ldisc.c:738 tty_ldisc_reinit+0x46/0x7b() sh kernel: [10222733.062526] Hardware name: PowerEdge R210 II sh kernel: [10222733.062528] Modules linked in: ipt_MASQUERADE iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 ip_tables x_tables sha1_generic arc4 ecb ppp_mppe ppp_async crc_ccitt ppp_generic slhc loop snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 i2c_core pcspkr evdev joydev dcdbas container button processor ext3 jbd mbcache sg sd_mod sr_mod crc_t10dif cdrom usb_storage usbhid hid mpt2sas ahci ehci_hcd libata scsi_transport_sas usbcore bnx2 nls_base scsi_mod fan thermal thermal_sys [last unloaded: scsi_wait_scan] sh kernel: [10222733.062568] Pid: 8662, comm: sshd Not tainted 2.6.32-5-amd64 #1 sh kernel: [10222733.062569] Call Trace: sh kernel: [10222733.062572] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b sh kernel: [10222733.062574] [<ffffffff811ff056>] ? tty_ldisc_reinit+0x46/0x7b Is there any way to get back the sshd working in interactive mode? I tried restarting sshd but that is no help. And somehow, I can not reboot the server. Tried sending shutdown -r now and reboot but it refuses to go down. Should I go ahead and request a physical reboot?

  Read the article

• Sudden and frequent hangs on desktop computer: mobo or CPU fault?

  - by djechelon

  I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

  Read the article

• Intell SSD + Win 7 after crash can not repair, can not re install

  - by Ori

  I have Lenovo w520, after i bought it i took away old hhd (no longer with me) and replaced it with intel ssd, it worked perfectly for 1 year or so, today my system fr0ze and after waiting for some time i didi hard reset - it wasn't able to boot anymore at all, i do not see any messages from windows ever, it only loads Intel boot utility that suggests to pick one of 3 devices to boot, it has my hdd there but nothing happens. /I dont have recovery tools from lenovo since i moved to another country, i got win 7 cd from a friend (came with his laptop) abd if in bios i have AHCI - it doesnt see my ssd, if compatible mode - it sees it but format not available, partition creation gives b\me 8007045 error. I tried diskpart, in compatible mode it sees my disk but doesnt do recover or clean all, also win 7 disk tools dont do anything if i try to do boot fix... I am ok with erasing it but i seem not to be able too, i jus tneed the machine to wpork asap, all my files are on external drives so i dont care about formatting. please help! I am given a very old machine by a friend so i am able to browse internet... it is under XP...

  Read the article

• DVD-burner disappears when using grub

  - by drblah

  This is a rather annoying problem I have with Linux on my laptop. Whenever I install any Linux distro that relies on grub (which is about 99 % apparently) it will mess up my DVD-drive and the drive will not be recognized after booting, no matter the OS (Ubunntu, Arch, Windows Vista or 7). I know the problem has nothing to do the DVD-drive itself, because I bought a new one a few months ago. I am also sure that grub is messing the drive up, because I have tried to use LILO, which worked fine (except for horrible boot times.) This problem have persisted through about 3-4 years and it is a pretty bad show stopper whenever I want to work with Linux. I had hoped it would get fixed over time, but no one seems to have the exact problem I have. The drive is connected with an IDE connection. Update: The old drive was a Toshiba Samsung SN-S082. I don't know the model number of the new one, but it is HP (I think). Things I have tried to fix it: Mess about with some BIOS settings like enabling AHCI and change some IDE settings. Installing a different boot loader DOES fix the problem but I would like to use grub.

  Read the article

• Suspected Corrupted Windows 7 MBR?

  - by AridDecay

  So, this may not be the correct place to put up my question, but i'll give it a shot. I'm having an issue repairing this computer. It was brought to me with the described issue of 'Not turning on' Later, I found that it would come with the error of 'No boot sector found on internal hard drive.' I assumed it was an MBR issue due to a virus or cutting a Windows update short. I booted into my trusty recovery enviroment and ran bootrec.exe /FIXMBR and restarted -- No luck I started to think (After multiple attempts to get the MBR sorted out, including creating a new boot sector) that the Hard-drive was possibly starting to cave in on itself, so I booted into a linux bootable CD and went to check the SMART data. Odd, say's it's inaccessible. That seems odd to me, considering it's a newer (two years old or so) Windows 7 computer. All new Hard-drives have SMART. So, I checked the BIOS. No mention of SMART anywhere. Greaaaat. I decided as a last-ditch effort to switch the hard-drive type to ATA in the BIOS (God knows why, I was getting frusterated) instead of AHCI. VOILA! It actually attempts to boot, gets halfway through the little windows animation, does an incredibly (Half a second) quick BSOD, and shuts down. Does anyone have ideas on what's going on here? I'm at my wits end.

  Read the article

• Why is my new PC so slow at startup?

  - by rumtscho

  Bought a new PC this weekend, and it works really good. Only I have one big problem: startup time. Its BIOS needs 62 sec to load, then from Grub start to pw entering screen it's another 26 sec. I think this is a lot, because my old PC needs 34 sec for BIOS and another 8 sec to pw screen. After I enter the pw, the desktop is usable with practically no delay on both. The new PC is a core i7-930, running a Lucid Lynx 64 bit from a Intel Postville SSD (no internal HDs). The old PC is a Pentium 4 celeron (forgot the clock speed) running a Lucid Lynx 32 bit from an ATA 100 hard drive. Neither PC is overclocked. The new one has boot sequence 1.DVD ROM, 2.SSD (connected over SATA in AHCI mode), 3. removable drive. The old one boots from 1. DVD ROM, 2. HDD, 3. Floppy. Neither has a second OS installed. The new one has less software installed than the old one (I think), but the boot time difference was noticeable even before I made any installs. As far as I know, just the SSD should be enough to make a noticeable difference in boot time. I thought that having a good mainboard on the new PC as opposed to the basic office model on the old one would also mean a faster loading BIOS. If these assumptions are right, I guess I must have misconfigured something in the BIOS of the new PC. How should I configure it for a fast boot? It has an ASUS P6X58D board with an AMI BIOS, if you need the BIOS revision number I could post that too.

  Read the article

• Can you help me understand my SATA/RAID options?

  - by andrz_001

  I've a gigabyte GA-M720-US3 motherboard. Recently, I noticed the following during boot: IDE channel 0 Master (none) IDE channel 0 Slave (none) IDE channel 2 Master (my hdd) IDE channel 2 Slave (my dvd drive) IDE channel 3 Master (none) IDE channel 3 Slave (none) Of course, the same information is contained in the BIOS/CMOS. The HDD is connected to the mobo via a SATA(2?) cable at the port(?) labeled SATA2_0. The DVD drive is connected by a similar cable at SATA2_1. Why doesn't the information displayed during the boot and in BIOS reflect how I plugged the cables in? I mean, why "none" for channel 0 when there is something in SATA2_0. (or is that serious naivete on my part!?) Where's Channel 1 master and slave? Since these are SATA cables and not the IDE ribbons from a time ago, why the whole master/slave declaration during boot and in BIOS? Should my BIOS reflect the fact that these are SATA cables? I mean, in BIOS, should the "Onchip SATA mode IDE" be set to RAID or AHCI instead of IDE? Any replies, answers, suggestions, links, tips will be much appreciated. Thank you in advance!

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• How to improve Samba performance on VirtualBox machine?

  - by ColinM

  I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

  Read the article

• Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

  - by Fazil

  I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

  Read the article

• Backtrack, Wi-Fi not working

  - by hradecek

  I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

  Read the article

• How to prevent an SSD from disappearing from BIOS

  - by Midimatt

  I've only recently upgraded my old machine to a new one with a brand new 60gb SSD as my boot drive and a 1TB main drive. Paranoid about completely breaking my SSD, I read up on a lot of issues that I needed to watch out for, including making sure AHCI was turned on and trim enabled. PC has been working fine for a few weeks now, until today. My wife was watching some TV on the machine when it started to act strange and eventually blue screened. She rebooted and the boot mgr was missing. When I got home from work I checked the BIOS and the drive had disappeared. I panicked and looked up some possible fixes, and I discovered a large amount of people having problems with the drive firmware, especially on OCZ Vertex and Agility drives, and my drive is an Agility 3 drive. The problems included blue screens followed by missing drives, and a solution was to reset the CMOS and try again. This worked, and now everything seems to be working fine. My question is, is there any way to prevent this from happening? Am I missing a setting for my SSD? All of the posts I found were from early to mid-2011 nothing for the end of 2011 to 2012. So I am wondering if I've missed anything. EDIT: Checked my drives firmware and it is 2.15, which has had issues reported by users.

  Read the article

< Previous Page | 5 6 7 8 9 10 11  | Next Page >