Search Results

Search found 314 results on 13 pages for 'dice'.

Page 9/13 | < Previous Page | 5 6 7 8 9 10 11 12 13  | Next Page >

• Can't connect to public WiFi with MacBookPro at coffee shops and libraries

  - by Nathan Bowers

  The Problem: I can't connect to public, unencrypted WiFi at my local public library or Peets Coffee. My Setup: Late 2006 MacBookPro running 10.5.8. I have Parallels installed. It's supposed to work like this: 1) Connect to their unencrypted WiFi network 2) Open a browser which redirects you to their "enter password/agree to terms" page. 3) Browse normally. I can connect to the WiFi network, but when I try to authenticate I always get stuck in a redirect loop. It's been like this for a while. Even before I upgraded to 10.5.8. I never have trouble with encrypted networks or regular open WiFi. What I've tried: Disabling Parallels connections in Network Prefs. Superstition: somehow Parallels installed something in the network stack that's messing me up. Pinging the IP address of the WiFi node I'm connected to. I can ping it, it's there, but I still get stuck in this authentication redirect loop. Tried different browsers, tried different cookie and security settings. Even tried IE under Parallels. No dice. Tried flushing DNS cache. Asked library and coffee employees for help. It didn't go well. My Question: Anybody else have this problem? What should I be looking for?

  Read the article

• Installing sqlite gem fails on AWS Linux instance with sqlite-devel libraries installed

  - by Scott

  Hi, I'm running an instance built off ami-595a0a1c. I am trying to install the sqlite3 (or sqlite) gem and it's failing with the below error: $ sudo gem install sqlite3 Building native extensions. This could take a while... ERROR: Error installing sqlite3: ERROR: Failed to build gem native extension. /usr/bin/ruby extconf.rb checking for sqlite3.h... no sqlite3.h is missing. Try 'port install sqlite3 +universal' or 'yum install sqlite3-devel' and check your shared library search path (the location where your sqlite3 shared library is located). extconf.rb failed * Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby --with-sqlite3-dir --without-sqlite3-dir --with-sqlite3-include --without-sqlite3-include=${sqlite3-dir}/include --with-sqlite3-lib --without-sqlite3-lib=${sqlite3-dir}/lib Gem files will remain installed in /usr/lib64/ruby/gems/1.8/gems/sqlite3-1.3.3 for inspection. Results logged to /usr/lib64/ruby/gems/1.8/gems/sqlite3-1.3.3/ext/sqlite3/gem_make.out Typically, this just means you need to install the development libraries and everything is cool. However, I have installed the sqlite-devel packages and still no dice. Since this is the Amazon Linux instance, I'd rather not add more repositories than the ones Amazon provides if possible. What can i do to get this thing to compile? Thanks for any insight! From a brand new instance, here's what I've done: $ sudo yum install rubygems ruby-devel $ sudo gem update --system $ sudo gem install rails $ rails new app $ cd app $ rails server Could not find gem 'sqlite3 (= 0)' in any of the gem sources listed in your Gemfile. $ sudo yum install sqlite-devel $ sudo gem install sqlite (or sqlite3 -- same result) See breakage above

  Read the article

• Computer locking up, looking for bootable hardware diagnostic tool.

  - by Carl Menke

  Well today I helped my friend build a computer. All went pretty well until we got to installing Win7. Thing is, we thought, it was crashing constantly. I adjusted pretty much every setting in the BIOS and removed as much hardware as possible to try and prevent a crash. No dice. So far I've tried running an Ubuntu live cd without the harddrive installed. Nope, crashed on boot. And then I just tried Microsoft's ram utility disk and it eventually locked up on that (the ram passed though). So it seems to me like it's either the CPU (AMD PhenomII x3) or the motherboard that could be bad, but I don't know how to test them individually for problems. I thought it could be a overheating issue, but the BIOS reports that the CPU temp is fine idling around 34C. Any advice or diagnostic disk that could help me out? TL;DR: Computer locks up frequently during use (cannot even boot/install an operating system), memory is fine, probably CPU or Mobo, BIOS says CPU temps are fine. What should I try?

  Read the article

• Launching Installer Via Powershell and WinRM and Nothing Happens

  - by Nick DeMayo

  I'm currently working on a Powershell script to run some Microsoft Hotfix installers remotely on several Windows Server 2008 R2 servers that I manage. Basically, the script copies all the appropriate files up to the server, and then runs the installer via Invoke-Command, like so: function InstallCU { Write-Host "Installing June 2013 CU..." Invoke-Command -ComputerName $ServerName -ScriptBlock { Start-Process "c:\aaa\prjcusp2\ubersrvprj2010-kb2817530-fullfile-x64-glb.exe" -ArgumentList "/passive" } } If I run the "Start-Process" command locally on the server, the installer runs properly. However, when trying to run it remotely, nothing happens (actually, I can see the installer start up in Task Manager, but it closes a couple seconds later and doesn't run). I've attempted giving the Invoke-Command -Credentials, I've turned off UAC on the server, and I've ensured that my WinRM settings (running 'winrm quickconfig' and setting TrustedHosts to *) are correct. I've also tried having the Invoke-Command script run a local Powershell script to run the installer and changing the Argument from '/passive' to 'quiet' (in case it can't remotely launch something that has a UI), but again, no dice. Is there anything else I can try, or am I just not going to be able to do this?

  Read the article

• IIS6 Virtual SMTP server isn't coming back up automatically after a system restart

  - by Julian James

  I've got a virtual server running Win2008 RC2. I've set up IIS6 with a virtual SMTP server on it to be the mail provider for the websites I'm hosting there. It all works great, but if for some reason the server reboots (auto updates are still enabled - I'm trying to make this as little work as possible as we've got a Lot of clients), the IIS6 doesn't restart the SMTP server. The failure causes 500 errors on the current setup, so I'm spending half the day apologising. Any ideas? In Services I've set everything to come back up automatically, but still no dice. As soon as I restart the SMTP, no problems, all the mail gets sent. It's working perfectly, it just won't restart on it's own. I'd really rather not turn auto updates off as we're such a small company I just can't spare the time to be manually updating 15 copies of windows every time MS decide there's a security patch. All advice appreciated! BTW, I am a complete newb to these forums. I searched but couldn't find an answer, so please be nice. But firm. I've got to learn here.

  Read the article

• Ubuntu Wubi "drive" failure; mount drive in XP?

  - by 618034

  Hi there, I installed the Wubi distribution of Ubuntu on a separate partition (which is silly, since why do I care if Windows can still manage the partition?) a few months back; it was pretty awesome, until Linux hosed. At this point, I can get Ubuntu to boot if I try really hard through grub, but once it does start, the screen is hosed, so no dice. At this point, I'd like to wipe it all and start over, but I need to get some stuff off the "disk". The Wubi install makes this difficult, since the "disk" is a flat file on an NTFS partition. I've done just about everything I can think of — I renamed the virtual disk .iso, mounted it with VirtualCloneDrive, then used whatever magic EXT3 (EXT4?) readers I could dig up on the Internet to parse the mount — but nothing's working. Can you offer any suggestions? The "disk" is currently in D:\ubuntu\disks\root.iso. Many thanks! (I may be high-latency at the moment, apologies if I don't address follow-ups quickly)

  Read the article

• OpenVPN (Tunnelblick) Suddenly Dropping Constantly

  - by Jeremy Privett

  I've been using Tunnelblick on my Mac for OpenVPN for about a year now. All of a sudden, this morning, it decided that it was going to take a nasty turn for the worse with no explanation. Here are the symptoms I'm seeing: I can connect to the VPN fine, initially. After about 2 - 5 minutes of no interruption, the connection suddenly dies. I can still see the VPN route using netstat -rn, and Tunnelblick believes it's still connected. No VPN traffic can go through and I can't even ping the VPN gateway. Eventually, Tunnelblick will catch on that the connection has died (usually about 5 - 10 minutes later) and shoot itself to restart and then the cycle starts over again. I've tried everything I can think of to figure this one out. I've completely flushed my system by rebooting and removing Tunnelblick and all traces of OpenVPN from my system and re-installing from scratch. No dice, same problem. I'm at my wits end, because I desperately need to get this fixed as the VPN is required for me to be able to do my job. Any ideas you have would be greatly appreciated.

  Read the article

• How can you connect to a SQL Server not on your domain?

  - by scotty2012

  I have a test machine that's not allowed on our domain because we are testing corporately unsupported applications (SQL 2008 and Server 2008). I want to use management studio to connect to the SQL2008 server but can't get it working. I have authentication set to mixed-mode, I've checked 'allow remote connections to this server', but when I try to access it, I get the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 53) Since it says the provider is Named Pipes, I enabled Named Pipes on the server, but still no dice. I've tried connecting to the system name, the IP, the system name\instance and IP\instance, all to no avail. Is what I'm trying to do not possible? Edit: Well, through some basic troubleshooting, I've found that I can't ping the server from my client computer, but I can ping the client computer from the server? They are both plugged into the same switch, and are sitting next to each other. The windows firewall on the server is turned on, is there some specific settings I need to enable? DAH! So it was the firewall blocking me. How can I enable the firewall and still connect?

  Read the article

• DLINK WBR-1310B Wireless Router seems to hang...

  - by Ira Baxter

  I have a brand new DLINK-1310B Wireless Router (box never before opened, although I bought it the neighborhood computer junk store). I am using it at home (and in fact am using it this instant from a wireless laptop). When operative, I can ping it at 192.168.0.1, and I can log into it from the PC attached to by LAN and from the wireless PC at //192.168.0.1. In the course of the day since I've installed, it seems to have locked up 3 times. Each time the symptoms are my web browser (or other internet service) stops with a "No internet connection" error. Attempts to contact the router via 192.168.0.1 get no reaction, from either the wireless laptop or from the hardwired PC sitting next to it. It doesn't respond to pings to that address either. Rebooting fixes it. Its brand new. I've seen discussion in other questions about aging cheap electronics. Its too new to be aged. Anyboyd else seen this behavior with a DLINK-1310? Or do I just need to exchange it for another and try again? (I hate rolling dice, I bought the DLINK becuase a previous Linksys died of apparant heating problems). Remarkably, nobody talks about how much software is in a router. Is the stuff just buggy?

  Read the article

• Windows 7 boot issues

  - by Michael

  Ok, I tried to install linux and dual boot my laptop with 7 ultimate. I messed up. When I tried to boot to 7 it said no. Something along the lines of device not found. So I being young and stupid I uninstalled linux which I could boot into, and I still could not boot to windows. Next step was to run the startup fixes from the boot cd. Swing and a miss, I also ran the fixmbr and fixboot. Which brings us up to my current place. I installed 7 again on my blank partition in hopes I could access my other partion. No dice. So my question to yall is how can I fix my original filesystem or at least get to the stuff on it. In the new 7 install the old partion does not even have a drive letter. That is my sad story any help would be apreciated.

  Read the article

• Word 2003 will not show up in Windows 7

  - by invadersil

  I just installed Windows 7 over the holiday and it went swimmingly well. Today I finished up a few things like installed MS Office 2003. That went well too, until I tried to open up Word. When I try to open up Word on its own, it comes up in the application bar but the application window does not show. I use Word as the editor in Outlook which does work. I also discovered that I can start it up in safe mode and it will work normally. But normal startup just doesn't show me anything. Oddly, if I start typing stuff while the app is selected in the app bar and then try to close it, it pops up a message asking if I want to save it. I tried running the compatibility utility within Windows 7 but still no dice. Has anybody seen this issue yet? The other Office apps start normally. Edit: More info: Windows 7 Pro 64-bit. Office is patched up to SP3. And last time I checked, there were no updates either (and fully updated with KBs after SP3) And I did a fresh install of Windows 7.

  Read the article

• Forward mDns from one subnet to another?

  - by user37278

  Is there an ipfw rule that can easily forward mDns packets from one subnet to another? I have a Snow Leopard Server machine serving as the gateway between the two subnets and would like for machines in each subnet to see the services available in the other subnet. The gateway machine is already confirmed as configured correctly such that packets route correctly between the two subnets (ping works, traceroute shows the subnet hop, etc). My problem in designing a ipfw rule is that I don't know how to instruct that I would like multicast packets addressed to 224.0.0.251:5353 on en0 to be addressed to the same ip/port but on fw0 (the other interface). I attempted a rule such as fwd 192.168.10.1 log udp from 192.168.1.0/24 to 224.0.0.251 recv en1 to force the packet to hop over to the other interface (from en1 to fw0), but no dice. The ipfw log shows that the rule is being triggered by packets, but tcpdump isn't showing any packets on the other interface. Also, the only other firewall rules in place are the divert port 8668 and rule #65535 "allow any to any". Any suggestions? Thanks.

  Read the article

• Calendar booking issue - Exchange 2003 and 2010

  - by NaOH

  In our organization we are running Exchange 2003 and 2010 simultaneously, with the hopes of migrating everyone to Exchange 2010 sometime within the next few months. Everyone is using Outlook 2010. Recently, we had an issue with transaction log storage on the Exchange 2003 server. This was resolved, but for some reason no meeting rooms on the Exchange 2003 server will automatically book meetings any longer. I have played around with this for a while, changing calendar permissions, turning resource scheduling off and back on, etc. No dice. My next step was to try migrating a resource to the Exchange 2010 server. After doing so, and setting it up as a Room, enabling Auto-Accept and removing the EnableDirectBooking registry entry on my PC, I can book a meeting with this room. If EnableDirectBooking is enabled, I get an error message stating: "Meeting Room" declined your meeting because it is recurring. You must book each meeting separately with this resource. This is despite the fact that the meeting I'm attempting to create has no recurrence. Now, I have also created a new test Room from scratch on the Exchange 2010 server, and I can book a meeting with this Room regardless of whether or not I have the EnableDirectBooking reg entry in place. All users here have this registry entry, and I'd rather not have to figure out how to push something out to remove it from every PC. Rather, I'd like to figure out what's different between the configurations of these two meeting rooms so that I could book a meeting room regardless of whether EnableDirectBooking is enabled or not. Any ideas, anyone? Thanks!

  Read the article

• Fix bad superblock on logical partition

  - by Chris

  I was following http://www.howtoforge.com/linux_resi...xt3_partitions and when i reboot and run: root@Microknoppix:/home/knoppix# fsck -n /dev/sda7 fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) fsck.ext2: Superblock invalid, trying backup blocks... fsck.ext2: Bad magic number in super-block while trying to open /dev/sda7 The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> so i ran e2fsck with all the block numbers that you need (forget exactly what tool i used to find where the superblocks are hidden) no dice then i ran testdisk and had it look for the superblock, no results anyone have any ideas? fdisk -l for reference: root@Microknoppix:/home/knoppix# fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x97646c29 Device Boot Start End Blocks Id System /dev/sda1 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 38912 312046593 f W95 Ext'd (LBA) /dev/sda5 64 326 2104320 82 Linux swap / Solaris /dev/sda6 * 327 2938 20972544 83 Linux /dev/sda7 2938 38912 288968672+ 83 Linux To be honest it looks like I lost it... Next step if that happens is to dump the partition to an image file and hope i can find or write some software to parse through the data looking for known file headers, i think.

  Read the article

• BIOS not detecting working SATA hard drive.

  - by Evan

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Custom Extensions on Managed Chromebooks

  - by user417669

  I am a developer looking for the best way to set up different schools with their own custom, private extensions (ie School A should be the only one with access to Extension A). Theoretically, I am aware that there are a few ways to get a custom, private extension pushed out on a domain: Host the .crx on a server and click "Specify a Custom App" in the management console. Create a Domain App by uploading a zip to the Chrome Web Store Upload the extension from my developer account to the Chrome Web Store and publish to a single "trusted tester," or make it unlisted Option (1), hosting the .crx, has not been working. I am not sure why, but the extension is simply not pushing out. I link directly to the crx file, which has the right ID and MIME type, still, no dice. If anyone has any tips or suggestions for getting this to work, I would love to hear them! Option (2), having the school create a domain app, seems a bit inefficient because it requires all schools to upload their own zip. So essentially I would have to email a zip file to the school, and have them publish it. All updates to the extension will also require a similar process, so this doesn't seem ideal. I doubt that option (3) would work. If I published to the admin as a "trusted tester", I don't think that the other people in the domain would be able to access it. If it is unlisted, I do not know how an admin could find it in the Chrome Web Store dialog. Also, I would rather avoid security through obscurity. Has anyone had success with hosting the extension and using the Specify a Custom App feature? Any other suggestions for getting a Custom Extension pushed out by the management console? Thanks so much!

  Read the article

• How should I configure nginx caching headers for a "baked" static file blog? (Octopress)

  - by Doug Stephen

  I recently deployed an Octopress blog (which is a blogging platform built around Jekyll). It's a static-site blog generator, with no dynamic content or databases to muck about with. It's being served up by nginx. My question is, what is the appropriate expires directive or Cache-Control header that I should set to make sure that visitors get the most up-to-date version of the site when they visit without having to manually refresh? Since the site is just .html files it seems to get cached pretty aggressively. I've tried a million different combinations of expires modified + xxxx and even straight up expires off but I can't seem to wrap my head around it. I'm very new to dealing with caching like this, specifically, on static files that change frequently, and obviously if the site hasn't been changed then I'd like for it to be served up out of the cache. Update (still not solved though): I found open_file_cache, tweaked that. Still no dice. It seems like what I might want to do is use nginx as a proxy cache and use Apache with ETags? Is there really no convenient way to make nginx play nicer with conditional requests from the client? TL;DR: I'm running a static-file blog and I'd like to set up nginx to only serve from the cache if the blog hasn't been updated recently, but I'm too stupid to figure it out myself because I'm relatively new to web servers.

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• Compaq Motherboard gives "CPU Fan Error"

  - by John

  I have a motherboard for a HP business desktop dx5150 PC. The model written on the board is "MS-7050" and it is for an AMD socket 939 processor. I got everything installed in it, and when I turned it on, it showed a message stating that there was a "CPU Fan Error" (or some similar language) and then turned off. It never stays on for more than about 30 seconds, probably less. The fan had previously been working great, but I replaced it anyway with a brand new Cooler Master fan. This did not work. I then reset the BIOS with the jumpers on the board, no dice. I replaced the CMOS battery. Same error. I then replaced the entire computer power supply with a brand new Antec, same error. The fan header is keyed, and has room for 3 pins. The CPU fan is designed the same way, so its not that I'm missing a temperature sensor or anything. Can anyone give some suggestions? Especially maybe some secret keystrokes to bypass this error?

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• Missing drive space in Server 2003

  - by Tim Brigham

  I have two drives used for SQL backups which for the last week have been acting strange - the free space indicated by windows is far off from what windirstat, etc indicates. There should only be about 60 GB of drive space used and there is about 160. This would match the utilization if the two last backup files were still residing on disk. SQL server is 2000, OS Server 2003 x64. Running on a VMware 5.0 cluster. OSSEC and McAfee for this system shows clean. My current plan is to temporarily attach one of these drives this drive to another VM for analysis. Is there anything more I should be looking at? There were a lot of pages on the net when I was looking for documentation on this issue but I haven't found this case described. EDIT: Unfortunately even a full reboot did not clear this behavior. I also used process explorer to look for open file handles. No dice.

  Read the article

• Vim: How to Install Airline?

  - by MunkyCheez

  I'm just getting started with Vim. It's a fun experience, but I've found it to be kind of overwhelming. I'm trying to get this plugin installed, vim-airline, but I'm having a lot of trouble. The Installation section on the Github page simply states: copy all of the files into your ~/.vim directory Presumably, this means download the .zip, extract it, and copy all of those files into ~/.vim/. I did this, but Vim just starts up like normal, and running :help airline just gives: Sorry, no help for airline I assume that this means it isn't getting installed. Also, the statusbar remains the same. I'm new to Vim and would really like to get this working. Thanks in advance! EDIT: I also tried putting the files into /usr/share/vim/vim73/. No dice. EDIT 2: I ran :helptags ~/.vim/doc and now the help-page displays when I type :help airline, but I'm still not getting the plugin itself (the status bar). Vim looks the same, but it can now display the help page.

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• How do I start the Workstation Service so I can use `net use`?

  - by nitefrog

  I have a Windows 7 machine that logs into a domain. The machine can net view and see the different shares, but when I try to use, net use * \\name\share, I get an error stating that the service is not started. Yet when I issue a net start, it states the service is already started. My other win7 machines work fine; they can see and use any of the shares. Is there a security setting that needs to be disabled or enabled? I really need to get this working, and I have no other ideas as the other machines have no problem accessing the shares on different systems. The error I am getting is , "The Workstation Service Has Not Been Started", but like I said other machines can connect fine, and when I issue a, "net start workstation", it states the service is already started. In addition the error number I am receiving is 2138. UPDATE: On the machine that is having issues. From the troubled machine if I issue a Net View \\name I can see all the shares on the machine I want to connect to. When I try to net use * \\name\sharename I get the error The Workstation service has not started. I have set both settings sc config lanmanworkstation start = auto and sc config lanmanserver start = auto on the Windows7 computer that is having issues. I have rebooted the computer and still no dice. I can net view any computer on the network and see all shares, but I cannot access any of the shares in which I can see. In the registry under the HKLM\System\CurrentControlSet\Services Both LanmanServer and LanmanWorkstation start is set to 2. Screen capture of net use and view: The Services: This is really weird. What am I missing? It has to be a security setting...

  Read the article

• Nginx Server Block Not Working? - Already running other vhosts just this one not working

  - by daveaspinall

  Im running a Debian 6 LEMP server with multiple virtual hosts and everything has been fine for 5 or so sites. But I've just tried adding another but for some reason it's just not working. By not working I mean in Chrome I get the "Oops! Google Chrome could not connect to subdomain.domain.net" error. I've changed the domain for security to subdomain.example.com and the IP is masked. Hosts file (I have multiple sub domains): xxx.xxx.xx.xxx *.example.com *.example Server Block: server { listen 80; server_name subdomain.example.com; access_log /srv/www/subdomain.example.com/logs/access.log; error_log /srv/www/subdomain.example.com/logs/error.log; root /srv/www/subdomain.example.com/public_html; location / { index index.html index.htm index.php; } location ~ \.php$ { include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I've created the system link to the file in the /etc/nginx/sites-enabled/ directory and restarted/reloaded nginx. DNS seems fine: # ping -c 2 subdomain PING subdomain.example.com (xxx.xxx.xx.xxx) 56(84) bytes of data. 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=1 ttl=64 time=0.035 ms 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=2 ttl=64 time=0.048 ms Checking the file with cURL works: # curl http://subdomain.example.com HTML - OK Emptied browser cache but still no dice. Anything I'm missing? Like I mentioned, I have a few sites running fine on the server currently so php-fpm etc etc are working. Any help would be much appreciated! Cheers, Dave

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13  | Next Page >