Search Results

Search found 8056 results on 323 pages for 'external'.

Page 9/323 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• Toshiba External Hard Drive freezes computer

  - by Ephraim

  I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

  Read the article

• Formatting an external HDD stuck at 70%

  - by mahmood

  My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

  Read the article

• Dropped WD External Harddisk, now it's shown as "Not initialized"

  - by Phelios

  So, the WD my passport external harddisk is dropped, and after that, the computer is unable to read it anymore. I was hopping if I can just find another case to try if the harddisk is still readable, but looks like the hard drive itself is not a normal SATA or PATA drive. I think it's modified. So, I can't find another case that I can try on. In the computer, I still can see the drive in the "Disk Management", but it's shown as Uninitialized, no size, and no drive letter. I've also tried a couple of recovery tools. Some can't detect at all, there is one (find and mount software) that can detect but shows 0 size. None of them can recover the data. WD is willing to replace it with a new one, but I still need to recover the data. Any way I can recover the data? UPDATE: I tried initialized it from the windows Disk Manager, but it give error "The request could not be performed because of an I/O device error."

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

• External-Harddisk drive couldn't run unless in safe mode

  - by zfm

  This is the strangest thing ever happened to me... I have an external harddisk drive (ext-HDD), bought around 2 years ago (don't know whether this is an important issue or not). Here, I have a video file (.avi) in my internal harddisk dive (HDD), it worked very well, then I copy it to my ext-HDD, but I couldn't run the file directly from my ext-HDD! I tried to copy it back to my HDD (from the ext-HDD), and now the copy couldn't be run on my HDD too. Remember that I copy the file, so the original one was still there. I tried to go to safe mode (forget to mention, I use Windows 7 Pro), and this is where the strange thing happened, the copied files (both in ext-HDD and HDD) can be run in this safe mode. So, my question is, what could actually be happened there? PS: My ext-HDD is Axioo, 250 GB, exFAT... Edited: Currently I used MacOSX, and the file in the harddisk still can't be run. I haven't tried safe mode for Mac (is there one?), but will try later (if there is)

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• Recovering data from an external hard drive

  - by CCallaghan

  I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

  Read the article

• Can the Visual Studio (2010) Command Window handle "external tools" with project/solution relative p

  - by ee

  I have been playing with the Command Window in Visual Studio (View-Other Windows-Command Window). It is great for several mouse-free scenarios. (The autocompleting file "Open" command rocks in a non-trivial solution.) That success got me thinking and experimenting: Possibility 1.1: You can use the Alias commands to create custom commands Possibility 1.2: You can use the Shell command to run arbitrary executables and specify parameters (and pipe the result to the output or command windows) Possibility 2: A previously setup external tool definition (with project-relative path variables) could be run from the command window What I am stuck on is: There doesn't appear to be a way to send parameters to an aliased command (and thus the underlying Shell call) There doesn't appear to be a way to use project/solution relative paths ($SolutionDir/$ProjectDir) on a Shell call Using absolute paths in Shell works, but is fragile and high-maintenance (one alias for each needed use case). Typically you want the command to run against a file relative to your project/solution. It seems you can't run the traditional external tools (Tools-External Tools...) in the command window Ultimately I want the external tool functionality in the command window in some way. Can anyone see a way to do this? Or am I barking up the wrong tree? So my questions: Can an "external tool" of some sort (using relative project/solution path parameters) be used in the Command Window? If yes, How? If no, what might be a suitable alternative?

  Read the article

• Moving an external hard drive while running

  - by user1108939

  I mean physically moving the drive around. I've never dealt with external hard drives before. Just plugged this wd mypassport to test the transfer rate. At one point I 'safely ejected' the drive. A minute later I decide to check the underside of the drive, not realizing the disk is still spinning. I lift the drive, rotating my writs about 70 degrees to the left... I hear a sequence of three high pitched sounds. I couldn't determine whether that was an indication beep by an internal security feature or the head scratching the plate (oh god...). Drive stops and usb power is disconnected. I reconnect it - it shows up fine - reads/writes. The drive was not reading/writing when i moved it. Did I damage my drive? Are these things that fragile? I thought them to be at least as durable as a standard 2.5" internal drive. Am I mistaken?

  Read the article

• How can I extend the desktop onto an external monitor/projector?

  - by hellocatfood

  I've plugged in a projector into my laptop and I'm attempting to extend the desktop onto it (so that I can run a full screen app on the projector and have the controls on my laptop). I'm able to mirror the screens effectively (it does this by default) but I can't extend it. When I untick "Mirror screens" and press apply it asks me to log out and then back in again but it goes back to mirroring the screens. I'm able to extend desktop on to my external monitor at home, just not this projector. Is there a manual way or other way to do this other that through Monitors setting? My computer model is Dell Studio 1555: Pentium Dual Core T4300(2.1GHz,800MHz,1MB), 4096MB 800MHz DDR2 Dual Channel, 512 MB ATI Mobility RADEON HD 4570 using the ATI proprietary driver. My screen resolution is 1366x768 (16:9) The projector that it wont connect properly is a Hitachi CPX3. That page specifies that it's especially designed for projectors that use 16:10 aspect ratio, but considering my external monitor at home uses 4:3 should the differences in aspect ratio matter or be causing this error?

  Read the article

• Why is my external USB hard drive sometimes completely inaccessible?

  - by Eliah Kagan

  I have an external USB hard drive, consisting of an 1 TB SATA drive in a Rosewill RX35-AT-SU SLV Aluminum 3.5" Silver USB 2.0 External Enclosure, plugged into my SONY VAIO VGN-NS310F laptop. It is plugged directly into the computer (not through a hub). The drive inside the enclosure is a 7200 rpm Western Digital, but I don't remember the exact model. I can remove the drive from the enclosure (again), if people think it's necessary to know that detail. The drive is formatted ext4. I mount it dynamically with udisks on my Lubuntu 11.10 system, usually automatically via PCManFM. (I have had Lubuntu 12.04 on this machine, and experienced all this same behavior with that too.) Every once in a while--once or twice a day--it becomes inaccessible, and difficult to unmount. Attempting to unmount it with sudo umount ... gives an error message saying the drive is in use and suggesting fuser and lsof to find out what is using it. Killing processes found to be using the drive with fuser and lsof is sometimes sufficient to let me unmount it, but usually isn't. Once the drive is unmounted or the machine is rebooted, the drive will not mount. Plugging in the drive and turning it on registers nothing on the computer. dmesg is unchanged. The drive's access light usually blinks vigorously, as though the drive is being accessed constantly. Then eventually, after I keep the drive off for a while (half an hour), I am able to mount it again. While the drive doesn't work on this machine for a while, it will work immediately on another machine running the same version of Ubuntu. Sometimes bringing it back over from the other machine seems to "fix" it. Sometimes it doesn't. The drive doesn't always stop being accessible while mounted, before becoming unmountable. Sometimes it works fine, I turn off the computer, I turn the computer back on, and I cannot mount the drive. Currently this is the only drive with which I have this problem, but I've had problems that I think are the same as this, with different drives, on different Ubuntu machines. This laptop has another external USB drive plugged into it regularly, which doesn't have this problem. Unplugging that drive before plugging in the "problem" drive doesn't fix the problem. I've opened the drive up and made sure the connections were tight in the past, and that didn't seem to help (any more than waiting the same amount of time that it took to open and close the drive, before attempting to remount it). Does anyone have any ideas about what could be causing this, what troubleshooting steps I should perform, and/or how I could fix this problem altogether? Update: I tried replacing the USB data cable (from the enclosure to the laptop), as Merlin suggested. I should've tried that long ago, since it fits the symptoms perfectly (the drive works on another machine, which would make sense because the cable would be bent at a different angle, possibly completing a circuit of frayed wires). Unfortunately, though, this did not help--I have the same problem with the new cable. I'll try to provide additional detailed information about the drive inside the enclosure, next time I'm able to get the drive working. (At the moment I don't have another machine available to attach it.) Major Update (28 June 2012) The drive seems to have deteriorated considerably. I think this is so, because I've attached it to another machine and gotten lots of errors about invalid characters, when copying files from it. I am less interested in recovering data from the drive than I am in figuring out what is wrong with it. I specifically want to figure out if the problem is the drive or the enclosure. Now, when I plug the drive into the original machine where I was having the problems, it still doesn't appear (including with sudo fdisk -l), but it is recognized by the kernel and messages are added to dmesg. Most of the message consist of errors like this, repeated many times: [ 7.707593] sd 5:0:0:0: [sdc] Unhandled sense code [ 7.707599] sd 5:0:0:0: [sdc] Result: hostbyte=invalid driverbyte=DRIVER_SENSE [ 7.707606] sd 5:0:0:0: [sdc] Sense Key : Medium Error [current] [ 7.707614] sd 5:0:0:0: [sdc] Add. Sense: Unrecovered read error [ 7.707621] sd 5:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00 [ 7.707636] end_request: critical target error, dev sdc, sector 0 [ 7.707641] Buffer I/O error on device sdc, logical block 0 Here are all the lines from dmesg starting with when the drive is recognized. Please note that: I'm back to running Lubuntu 12.04 on this machine (and perhaps that's a factor in better error messages). Now that the drive has been plugged into another machine and back into this one, and also now that this machine is back to running 12.04, the drive's access light doesn't blink as I had described. Looking at the drive, it would appear as though it is working normally, with low or no access. This behavior (the errors) occurs when rebooting the machine with the drive plugged in, and also when manually plugging in the drive. A few of the messages are about /dev/sdb. That drive is working fine. The bad drive is /dev/sdc. I just didn't want to edit anything out from the middle.

  Read the article

• Clicks or ticks every minute when HDD is idle [closed]

  - by Ramy

  Possible Duplicate: Clicks or ticks every minute when HDD is idle My HDD is a My passport... It's 2 weeks old. I hear this tick or click followed by another one about 8-9 secs later, and they repeat every minute almost exactly... They usually happen and the LED light blinking.. It's not like the other clicks you hear that indicate any inevitable HDD failure, it's much lower in volume. I don't know what that is, however it's different than the rest of the HDD usual sounds...It's close to the sound of the mouse click. It sometimes also happens when I access a file on the drive mostly after being idle for a while, sometimes randomly not really sure... The drive though is working well, the SMART report comes out OK and without warning, and disk management shows it healthy... What could be the cause of this??

  Read the article

• eventmachine and external scripts via backticks

  - by Maciek

  I have a small HTTP server script I've written using eventmachine which needs to call external scripts/commands and does so via backticks (``). When serving up requests which don't run backticked code, everything is fine, however, as soon as my EM code executes any backticked external script, it stops serving requests and stops executing in general. I noticed eventmachine seems to be sensitive to sub-processes and/or threads, and appears to have the popen method for this purpose, but EM's source warns that this method doesn't work under Windows. Many of the machines running this script are running Windows, so I can't use popen. Am I out of luck here? Is there a safe way to run an external command from an eventmachine script under Windows? Is there any way I could fire off some commands to be run externally without blocking EM's execution? edit: the culprit that seems to be screwing up EM the most is my usage of the Windows start command, as in: start java myclass. The reason I'm using start is because I want those external scripts to start running and keep running after the EM request is served

  Read the article

• Access Home Network Server via External Address (DSL vs Cable)

  - by Dominic Barnes

  For the last few months, I've been using a server on my home network for basic backups and hosting some small websites. Up until this past week, I've been using Comcast (cable) as an ISP and now that I've moved into an apartment, I'm using AT&T. (DSL) I've set up dynamic DNS and I can verify it works externally. However, I can't seem to access the public address from within the local network. Is there something DSL does differently from Cable that makes this frustration possible?

  Read the article

• Access Home Network Server via External Address (DSL vs Cable)

  - by Dominic Barnes

  For the last few months, I've been using a server on my home network for basic backups and hosting some small websites. Up until this past week, I've been using Comcast (cable) as an ISP and now that I've moved into an apartment, I'm using AT&T. (DSL) I've set up dynamic DNS and I can verify it works externally. However, I can't seem to access the public address from within the local network. Is there something DSL does differently from Cable that makes this frustration possible?

  Read the article

• mac: How to mount ejected external hdd again

  - by Maurice Kroon

  I've used my WD My Book 1TB for quite some time now. I always simply unplug it without officially 'ejecting' it. However, yesterday I did eject it (the partitions) before unplugging it. However, now, when i reconnect the hdd, it does not show the drives. It only shows the WD SmartWare partition (which is empty btw). The rest doesn't start. Does anyone know how to mount an unmounted disk? thx in advance!

  Read the article

• My external monitor flickers when using with Vista, but not with XP/Linux

  - by satish

  I bought a new Dell Monitor ST 2410 model (24 inch). It works great when I connect my XP laptop to it or my Linux box. But when I connect it to my HP Laptop (Dv 6000 series) which has Vista on it. The monitor flickers a lot. Tried out all modes/frequencies but didn't help me. Any ideas?

  Read the article

• Access Home Network Server via External Address

  - by Dominic Barnes

  For the last few months, I've been using a server on my home network for basic backups and hosting some small websites. Up until this past week, I've been using Comcast (cable) as an ISP and now that I've moved into an apartment, I'm using AT&T. (DSL) I've set up dynamic DNS and I can verify it works externally. However, I can't seem to access the public address from within the local network. Is there something DSL does differently from Cable that makes this frustration possible?

  Read the article

• Network attached external harddrive from another computer.

  - by Paul Knopf

  I have a server that is setup in raid. It is on the same network as my main computer. I would like to have some of the memory on my server to act as a network attached drive on my main computer. Basically, I want it to be a new data drive (similar two C:\, but 2nd drives are mostly E:). That way, I can reformat my main computer without loosing any important data. And the data that is saved (on server E:\ drive) is secured via raid mirroring.

  Read the article

• My EliteBook is not auto picking 1080p for external monitor, poor display on forcing

  - by Griever

  I'm connecting my Samsung LED S22A300B to my HP EliteBook 6930p through VGA out. Laptop has Intel 4500MHD video card. I have latest drivers installed for both card and monitor. Only 800x600 and 1024x768 are shown. A lot of other people get this problem when they use it with docking station as discussed here. But I am not using any docking station. The monitor works great with my desktop though. As advised on the aforementioned page, one of the things I tried was to force the resolution using Intel's "custom resolution" feature. I installed PowerStrip on my desktop and copied advanced timing values(front/back porch,sync width, etc.) from there and then used the same values while defining a custom resolution in my laptop's Intel graphics utility. As a result, I got the 1080p resolution but the display is poor. Text has some weird colored shadow and sometimes on images too. What should I do?

  Read the article

• 59 vs 60 hertz on external display via DisplayPort

  - by Shiki

  Don't know if this is a really specific question or you'll help me out. Please do. I just bought a DeLock DisplayPort cable for my Lenovo T500. Tried to use it with the in-built Intel MHD4500, no use. With the ATI HD3650 (you can switch between the two vga on this machine) I get a normal picture, but only on 59hz. On 60 I get a smaller desktop size (strange). Any idea what can cause this? Will I have any problem if I use the 59hz? (Was using the display with a VGA cable but I get a blurry picture with that (dont matter what device I attach, VGA is like this on this display) and thats why I wanted to change.)

  Read the article

• Powershell and long-running external tools?

  - by leeand00

  I'm trying to compact a MS-Access database using JetComp.exe using a powershell script. Here is the operative lines: # 4. Run JetComp LogWrite("Begin: Running JetComp") .\JETCOMP.EXE -src: $srcDB -dest: $dstDB | Out-Null #Run this command and wait for it to finish... IfErrorExit("Error Compacting Database") LogWrite("End: Running JetComp") The JETCOMP.EXE program seems to complete long before it is actually finished and the $dstDB ends up being smaller than the compact should even make it. Initially ($srcDB) it's about 1.8 GB and by the time the command finishes it's about 300,000 kb (about 0.29 gb) that's a pretty long way off from 1.8 gb which when compacted manually ends up being about 1.6 gb. Is there some sort of timeout I don't know about in powershell scripts? P.S. I know that when running JETCOMP.EXE manually, that the system often detects it as "not responding" even though it's actually getting the job done, and waiting long enough will allow it to complete.

  Read the article

• External Hardrive Not Reconized on Windows 7 at all

  - by Bella

  I Have a NextStar 2/5" from Vantec and its an 80G HD. I have used it many times on windows xp and it works fine. We just recently upgraded to windows 7 home premium and when I plug it in it beeps many times. I've tried all the USB plugs in my computer and its not those plugs. Haven't tried eSata because it uses a weird cable to plug into. People told me that when it beeps everything is corrupted, but works fine on xp. I tried installing the drivers online from their website and when I try it asks me to put in a cd which makes no sense because they are online drivers. When I go into device manager nothing comes up, it just acts like the HD is invisible. The beeping will stop eventually as it is plugged in, but with no result.

  Read the article

• Set Display Refresh Rate in OSX w/o External Utilities

  - by codedonut

  I have an iMac and an LG Flatron connected as a secondary monitor. The recommended resolution for the flatron is 1680x1050 @ 65.290 Hz (horiz), 59.954 Hz (vert). For some reason, OSX is choosing a slightly different set of scan rates and this is currently my best guess of why the monitor goes into power saving mode when connected to the iMac (but works fine on a PC). Now, I resolved this by installing switchResX and fudging the scan rates according to the specs in the manual. But how does one change these rates w/o 3rd party tools? Which config files need editing? Thanks

  Read the article

• Need a quality USB hub that is able to power external hardware

  - by Jon Erickson

  What is the most useful USB hub that you have had experience with. I have a Seagate FreeAgent Go that is powered by USB and I want to get a USB hub that is able to provide me with more USB ports and can power my harddrive.

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >