Search Results

Search found 24735 results on 990 pages for 'site ranking'.

Page 9/990 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• New AD-DC in a new Site is refusing cross-site IPv4 connections

  - by sysadmin1138

  We just added a new Server 2008 (sp2) Domain Controller in a new Site, our first such config. It's over a VPN gateway WAN (10Mbit). Unfortunately it is displaying a strange network symptom. Connections to the SMB ports (TCP/139 and TCP/445) are being actively refused... if the connection is coming in on pure IPv4. If the incoming connection is coming by way of the 6to4 tunnel those connections establish and work just fine. It isn't the Firewall, since this behavior can be replicated with the firewall turned off. Also, it's actually issuing RST packets to connection attempts; something that only happens with a Windows Firewall if there is a service behind a port and the service itself denies access. I doubt it's some firewall device on the wire, since the server this one replaced was running Samba and access to it from our main network functioned just fine. I'm thinking it might have something to do with the Subnet lists in AD Sites & Services, but I'm not sure. We haven't put any IPv6 addresses in there, just v4, and it's the v4 connections that are being denied. Unfortunately, I can't figure this out. We need to be able to talk to this DC from the main campus. Is there some kind of site-based SMB-level filtering going on? I can talk to the DC's on campus just fine, but that's over that v6 tunnel. I don't have access to a regular machine on that remote subnet, which limits my ability to test.

  Read the article

• Cisco ASA Site-to-Site VPN Dropping

  - by ScottAdair

  I have three sites, Toronto (1.1.1.1), Mississauga (2.2.2.2) and San Francisco (3.3.3.3). All three sites have ASA 5520. All the sites are connected together with two site-to-site VPN links between each other location. My issue is that the tunnel between Toronto and San Francisco is very unstable, dropping every 40 min to 60 mins. The tunnel between Toronto and Mississauga (which is configured in the same manner) is fine with no drops. I also noticed that my pings with drop but the ASA thinks that the tunnel is still up and running. Here is the configuration of the tunnel. Toronto (1.1.1.1) crypto map Outside_map 1 match address Outside_cryptomap crypto map Outside_map 1 set peer 3.3.3.3 crypto map Outside_map 1 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map 1 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_3.3.3.3 internal group-policy GroupPolicy_3.3.3.3 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 3.3.3.3 type ipsec-l2l tunnel-group 3.3.3.3 general-attributes default-group-policy GroupPolicy_3.3.3.3 tunnel-group 3.3.3.3 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** San Francisco (3.3.3.3) crypto map Outside_map0 2 match address Outside_cryptomap_1 crypto map Outside_map0 2 set peer 1.1.1.1 crypto map Outside_map0 2 set ikev1 transform-set ESP-AES-256-MD5 ESP-AES-256-SHA crypto map Outside_map0 2 set ikev2 ipsec-proposal AES256 group-policy GroupPolicy_1.1.1.1 internal group-policy GroupPolicy_1.1.1.1 attributes vpn-idle-timeout none vpn-tunnel-protocol ikev1 ikev2 tunnel-group 1.1.1.1 type ipsec-l2l tunnel-group 1.1.1.1 general-attributes default-group-policy GroupPolicy_1.1.1.1 tunnel-group 1.1.1.1 ipsec-attributes ikev1 pre-shared-key ***** isakmp keepalive disable ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** I'm at a loss. Any ideas?

  Read the article

• Cisco ASA site-to-site vpn not initiating phase 1 (not sending udp 500 packets)

  - by Sean Steadman

  I am hoping someone here can help me with my problem. I am trying to setup an IPSEC site-to-site VPN between two cisco ASA 5520's in GNS3 (both using 8.4.2). I have been unsuccesful in getting the tunnel up and it appears neither ASA is sending packets out,in regards to phase 1 and phase 2 (tested by using wireshark and seeing NO udp 500 packets). Doing show ipsec sa and such shows nothing. CALIFORNIA(config)# show ipsec sa There are no ipsec sas FLA-ASA# show ipsec sa There are no ipsec sas I will attach both configurations in two different pastebin files as to keep this post a bit cleaner. Essentially California side has 172.20.1.0/24 and Florida side has 10.10.10.0/24. California ASA config: http://pastebin.com/v0pngYzF Florida ASA config: http://pastebin.com/E2geybta Please let me know if there is any other vital information that could help. I have gotten IPSEC tunnels to work using openSwan (linux) and cisco routers but cannot for the life of me get ASA IPSEC tunnels to work. The ASDM is out of the question I only use cli. Thanks for any useful help!

  Read the article

• Creating a custom Publishing Portal Web site in SharePoint 2010

  - by Jourdan

  Custom Web sites built on SharePoint are cropping up everywhere (just visit topsharepoint.com to see). With that said, my question pertains to creating a fully customized, branded site using SharePoint as the CMS as depicted by many of the topsharepoint.com sites. I understand the concept of creating the custom master master page(s) (SharePoint 2010 even includes a minimal.master to start). The problems I have are: What site template does one use? In 2007 the recommended front-facing Web site site collection template was the Publishing Portal. Is this still the case? What navigation do you use? Do you leverage the OOB navigation? If so, how do you style it extensively? How do you keep the on-page editing capabilities within the new site template? Are there any online tutorials are walk-throughs that address all of these issues? I have been searching, but it's really sparse out there.

  Read the article

• Google indexing and ranking a custom domain served by Google App Engine

  - by Hugues

  I have a website served on the following URL : "http://www.plugimmo.com" which is a custom domain served by Google App Engine on the following URL : http://plugimmo.appspot.com Since a while I have tried to optimise the Google indexing and ranking with no success. The problem is that searching on Google the keywords in the title of my home page does not retrieve my website at all even not in the 1,000 first results : When checking the cached version of google ( cache:www.plugimmo.com), it says that the cached version is the one of 20-Aug-12 of "plugimmo.appspot.com". It looks there are several issues : 1 - The cached version is really old. I have made a lot of changes since the 20-Aug-12 and I saw the googlebot crawling my site several times. 2 - The cached version is for "plugimmo.appspot.com" 3 - When looking at the Google Webmaster tools, I see that the number of pages indexed for www.plugimmo.com is 0, but that can't be the case given the number of changes I made since then. My questions would therefore be the following : Why is the version of the cache so old although I saw the googlebot crawling the site many times since 20-Aug-12 ? Is there a problem with indexing a custom domain served by Google App Engine ? Why is the Google Webmaster tools showing 0 pages indexed although new pages have been crawled and that no errors have been reported in the indexing ? Also, the site has been developed with Google Web Toolkit. I have followed the guidelines regarding crawling Ajax sites. The home page when crawled by a robot is redirected to http://www.plugimmo.com/HomeSnapshot.html Thanks a lot for your help ! Hugues

  Read the article

• Ranking hit after site migration

  - by Ben

  I migrated my site from its old domain over a month ago. I followed Google Webmaster Tools completely, including 301 redirects from every existing URL to the new domain, and then submitting a change of address. Traffic continued as normal, but then a few days after submitting the change of address traffic plummeted to about 20-30% of what it was previously. Most of my traffic comes from organic search, and I can see that for the keywords I had targeted before and performed well with and am now ranking much much lower for. In some cases for low competition keywords I've only lost a few places, for higher competition terms I have really suffered. This has started to pick up a bit (one of my keywords I have risen from 195 to 100 in the last week), but it seems to be a very slow process. How seamless is this process normally? I was under the impression that this would not affect my rankings too severely, but it has now been a month since the move and recovery seems to be very slow, if at all. Is it likely that I've missed something? The only change is that I have moved what was the home page to be more of a sub-page, and now in its place is a magazine-style home page. I understand that links to the old site will now be pointing to the latter which means that rankings for some keywords attributed to the old home page will take a hit, but even on other pages that seem to fit in exactly the same page structure as the previous site I have seen a drop in rankings.

  Read the article

• Ranking hit after WP site migration

  - by Ben

  I migrated my site from its old domain over a month ago. I followed WMT completely, including 301 redirects from every existing URL to the new domain, and then submitting a change of address. Traffic continued as normal, but then a few days after submitting the change of address traffic plummeted to about 20-30% of what it was previously. Most of my traffic come from organic search, and I can see that for the keywords I had targeted before and performed well with and am now ranking much much lower for. In some cases for low competition keywords I've only lost a few places, for higher competition terms I have really suffered. This has started to pick up a bit (one of my keywords I have risen from 195 to 100 in the last week), but it seems to be a very slow process. How seamless is this process normally? I was under the impression that this would not affect my rankings too severely, but it has now been a month since the move and recovery seems to be very slow, if at all. Is it likely that I've missed something? The only change is that I have moved what was the home page to be more of a sub-page, and now in its place is a magazine-style home page. I understand that links to the old site will now be pointing to the latter which means that rankings for some keywords attributed to the old home page will take a hit, but even on other pages that seem to fit in exactly the same page structure as the previous site I have seen a drop in rankings. Any help would be greatly appreciated. Thanks!

  Read the article

• Site Server 3 user blacklisting

  - by Gary McGill

  I doubt that anyone even remembers Site Server 3 - most of those that had any contact with it will have spent the last decade trying to forget. But, on the off-chance that someone out there does remember it, perhaps you also remember what can be done to un-blacklist a user who has been blacklisted as a result of supplying incorrect login details 3 times? I have a user that's been blacklisted that I really really need to recover, and yet I can find no way to do this. (I'm not even able to figure out where the blacklist is stored - I'd be quite prepared to nuke it if that's what it takes).

  Read the article

• IPSEC site-to-site Openswan to Cisco ASA

  - by Jim

  I recieved a list of commands that were run on the right side of the VPN tunnel which is where the Cisco ASA resides. On my side, I have a linux based firewall running debian with openswan installed. I am having an issue with getting to Phase 2 of the VPN negotiation. Here is the Cisco Information I was sent: {my_public_ip} = left side of connection tunnel-group {my_public_ip} type ipsec-l2l tunnel-group {my_public_ip} ipsec-attributes pre-shared-key fakefake crypto map vpn1 1 match add customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside static (outside,inside) 10.2.1.200 {my_public_ip} netmask 255.255.255.255 crypto ipsec transform-set aes-256-sha esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map vpn1 1 match address customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 Myside ipsec.conf config setup klipsdebug=none plutodebug=none protostack=netkey #nat_traversal=yes conn cisco #name of VPN connection type=tunnel authby=secret #left side (myside) left={myPublicIP} leftsubnet=172.16.250.0/24 #net subnet on left sdie to assign to right side leftnexthop=%defaultroute #right security gateway (ASA side) right={CiscoASA_publicIP} #cisco ASA rightsubnet=10.2.1.0/24 rightnexthop=%defaultroute #crypo stuff keyexchange=ike ikelifetime=86400s auth=esp pfs=no compress=no auto=start ipsec.secrets file {CiscoASA_publicIP} {myPublicIP}: PSK "fakefake" When I start ipsec from the left side/my side I don't recieve any errors, however when I run the ipsec auto --status command: 000 "cisco": 172.16.250.0/24==={left_public_ip}<{left_public_ip}>[+S=C]---{left_public_ip_gateway}...{left_public_ip_gateway}--{right_public_ip}<{right_public_ip}>[+S=C]===10.2.1.0/24; prospective erouted; eroute owner: #0 000 "cisco": myip=unset; hisip=unset; 000 "cisco": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cisco": policy: PSK+ENCRYPT+TUNNEL+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,24; interface: eth0; 000 "cisco": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 000 #2: "cisco":500 STATE_MAIN_I1 (sent MI1, expecting MR1); EVENT_RETRANSMIT in 10s; nodpd; idle; import:admin initiate 000 #2: pending Phase 2 for "cisco" replacing #0 Now I'm new to setting up an site-to-site IPSEC tunnel so the status informatino I am unsure what it means. All I know is it sits at this "pending Phase 2" and I can't ping the other side, Another question I have is, if I do a route -n, should I see anything relating to this connection? Also, I read a few artilcle where configs contained the interface="ipsec0=eth0", is this an interface that I have to create on the linux debian firewall on my side? Appreciate your time to look at this.

  Read the article

• Problems pointing site to site in Hosts file

  - by coffeeaddict

  I'm on my localhost PC. I need to add an entry that maps our public site to our dev server. I tried several things with no luck: 192.168.1.40 oursite.com // where the IP here is our internal dev server or devserver oursite.com oursite.com devserver I'm not sure what I'm doing wrong here.

  Read the article

• JavaScript - Cross Site Scripting - Permission Denied

  - by Villager

  Hello, I have a web application for which I am trying to use Twitter's OAuth functionality. This application has a link that prompts a user for their Twitter credentials. When a user clicks this link, a new window is opened via JavaScript. This window serves as a dialog. This is accomplished like such: MainPage: <div id="promptDiv"><a href="#" onclick="launchDialog('twitter/prompt.aspx');">Provide Credentials</a></div> ... function launchDialog(url) { var specs = "location=0,menubar=0,status=0,titlebar=0,toolbar=0"; var dialogWindow = window.open(url, "dialog", specs, true); } When a user clicks the link, they are redirected to Twitter's site from the prompt.aspx page. On the Twitter site, the user has the option to enter their Twitter credentials. When they have provided their credentials, they are redirected back to my site. This is accomplished through a callback url which can be set for applications on Twitter's site. When the callback happens, the user is redirected to "/twitter/confirm.aspx" on my site in the dialog window. When this happens I want to update the contents of "promptDiv" to say "You have successfully connected with Twitter" to replace the link and close the dialog. This serves the purpose of notifying the user they have successfully completed this step. I can successfully close the dialog window. However, when I am try to update the HTML DOM, I receive an error that says "Error: Permission denied to get property Window.document". In an attempt to update the HTML DOM, I tried using the following script in "/twitter/confirm.aspx": // Error is thrown on the first line. var confirmDiv = window.opener.document.getElementById("confirmDiv"); if (confirmDiv != null) { // Update the contents } window.close(); I then just tried to read the HTML to see if I could even access the DOM via the following script: alert(window.opener.document.body.innerHTML); When I attempted this, I still got a "Permission denied" error. I know this has something to do with cross-site scripting. However, I do not know how to resolve it. How do I fix this problem? Am I structuring my application incorrectly? How do I update the HTML DOM after a user has been redirected back to my site? Thank you for your help!

  Read the article

• Unauthorized Access Exception using Web Deploy to Site when the site root is a UNC path

  - by Peter LaComb Jr.

  I am trying to use Web Deploy to deploy a site where the Site is rooted on a UNC path instead of a local drive. This is because I want to have a shared configuration, and have all servers point to the same UNC for content. That would allow me to deploy to one server and have all servers updated at the same time. I've created a share with everyone and users read/write. The NTFS permissions have the ID of the appDomain account as full control, and that is the same account that is configured as the specific user in Management Service Delegation. I can log on to the destination server as that ID, access the share and create/delete files. However, I'm getting the following exception in my Microsoft Web Deploy log on the destination server: User: Client IP: 192.168.62.174 Content-Type: application/msdeploy Version: 9.0.0.0 MSDeploy.VersionMin: 7.1.600.0 MSDeploy.VersionMax: 9.0.1631.0 MSDeploy.Method: Sync MSDeploy.RequestId: c060c823-cdb4-4abe-8294-5ffbdc327d2e MSDeploy.RequestCulture: en-US MSDeploy.RequestUICulture: en-US ServerVersion: 9.0.1631.0 Skip: objectName="^configProtectedData$" Provider: auto, Path: A tracing deployment agent exception occurred that was propagated to the client. Request ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e'. Request Timestamp: '8/23/2012 11:01:56 AM'. Error Details: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER Microsoft.Web.Deployment.DeploymentDetailedUnauthorizedAccessException: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. --- Microsoft.Web.Deployment.DeploymentException: The error code was 0x80070005. --- System.UnauthorizedAccessException: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. at Microsoft.Web.Deployment.NativeMethods.RaiseIOExceptionFromErrorCode(Win32ErrorCode errorCode, String maybeFullPath) at Microsoft.Web.Deployment.DirectoryEx.CreateDirectory(String path) at Microsoft.Web.Deployment.DirPathProviderBase.CreateDirectory(String fullPath, DeploymentObject source) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) --- End of inner exception stack trace --- --- End of inner exception stack trace --- at Microsoft.Web.Deployment.FilePathProviderBase.HandleKnownRetryableExceptions(DeploymentBaseContext baseContext, Int32[] errorsToIgnore, Exception e, String path, String operation) at Microsoft.Web.Deployment.DirPathProviderBase.Add(DeploymentObject source, Boolean whatIf) at Microsoft.Web.Deployment.DeploymentObject.Add(DeploymentObject source, DeploymentSyncContext syncContext) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleAdd(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.HandleUpdate(DeploymentObject destObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenNoOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.SyncChildrenOrder(DeploymentObject dest, DeploymentObject source) at Microsoft.Web.Deployment.DeploymentSyncContext.ProcessSync(DeploymentObject destinationObject, DeploymentObject sourceObject) at Microsoft.Web.Deployment.DeploymentObject.SyncToInternal(DeploymentObject destObject, DeploymentSyncOptions syncOptions, PayloadTable payloadTable, ContentRootTable contentRootTable, Nullable1 syncPassId) at Microsoft.Web.Deployment.DeploymentAgent.HandleSync(DeploymentAgentAsyncData asyncData, Nullable1 passId) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequestWorker(DeploymentAgentAsyncData asyncData) at Microsoft.Web.Deployment.DeploymentAgent.HandleRequest(DeploymentAgentAsyncData asyncData) This is shown as the following on the console of the machine where I run the deployment: C:\Users\PLaComb"C:\Program Files (x86)\IIS\Microsoft Web Deploy V3\msdeploy.exe" -source:package='C:\Packages\Deployments\applicationName.zip' -dest:auto,computerName='https://SERVERNAME:8172/msdeploy.axd',includeAcls='True' -verb:sync -disableLink:AppPoolExtension -disableLink:ContentExtension -disableLink:CertificateExtension -setParamFile:"C:\Packages\Deployments\applicationName.SetParameters.xml" -allowUntrusted Info: Using ID 'c060c823-cdb4-4abe-8294-5ffbdc327d2e' for connections to the remote server. Info: Adding sitemanifest (sitemanifest). Info: Adding virtual path (JMS/admin) Info: Adding directory (JMS/admin). Error Code: ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER More Information: Unable to perform the operation ("Create Directory") for the specified directory ("\someserver.mydomain.local\sharename\sitename\applicationName"). This can occur if the server administrator has not authorized this operation for the user credentials you are using. Learn more at: http://go.microsoft.com/fwlink/?LinkId=221672#ERROR_INSUFFICIENT_ACCESS_TO_SITE_FOLDER. Error: The error code was 0x80070005. Error: Access to the path '\someserver.mydomain.local\sharename\sitename\applicationName' is denied. Error count: 1.

  Read the article

• Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

  - by Steven

  We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

  Read the article

• So you want a French Site?

  - by juanlarios

  I thought I would write a quick write up of how to create a french site in SharePoint 2007. I'm not talking about a Variation but just a plain French Site from the ground up. There were some gotchas that I felt were worth blogging about. First:  go to Microsoft Telnet Article and follow the install instructions. Make sure that when you get to the download page that you select "French" as part of the drop down and you download and install the right language pack. I noticed that if you did not click the "change" button enven though I selected the 'french' language pack, it reverted back to the english language pack.   Second: You will notice a couple of things. When you go to central admin you will see the following:    Now you can pick between french site or english. You will get this if you install other language packs and they will be listed in the drop down. You will notice that you now have french headings and frech listings of sites. You see "Publishing" as a heading because I have a custom site definition that I deployed as a french site. Third: As you start navigating around and trying to create document libraries or sites you will start getting errors. Errors like the following: "Cannot make a cache safe URL for "SelectorControls.js", file not found. Please verify that the file exists under the layouts directory. " Troubleshoot issues with Windows SharePoint Services. Once you resolve the issue with this "js" file, you will find that there are other js files that are missing. The only problem is that if you are not fluent in French or the language you are trying to deploy, Well, you'll have a tough time understanding error messages as they will all be in the new language you are trying to deploy. So let's just talk about what happened when you installed the language pack. In the 12 Hive:  12/Template    you will now see a 1033 folder and a 1036 folder. The 1036 folder is the folder that was created and added as part of the language pack. What the above error is saying is that now that it's looking at the 1036 folder, well, it's missing some files. The nice thing is that these files are included in the 1033 folder (which is the English Language Pack). Simply copy and paste the controls from the one folder to the other. There will be more than one conflict so you will have to move serveral controls over. Can't remember how many but simply add them as error messages come up. I had to add some navigation controls and some content selectors.   Now that's all that you need to install the Frech Language pack anc reate site collections that are entirely in a another language. Do not mistake this with Variations, where you can have multiple language sites. For those of you doing a little bit extra with this, let me share what I was doing extra and what I needed to get it working for me. I had had a custom site definition which was obviously not showing up in my selection of french sites. I was under the impression that all sites in English would show up in french and that the sites were simply routed to a new Resource file for french content. And that is the case but there is a little extra that needs to be done if you have a custom site definition deployed:  First: Under hive 12/Template/1033/XML  there is a listing of site definition files that are deployed to the English side of things. If you navigate to 12/Template/1036/XML  and open one of the site definitions you will see that they are similar and reference the existing site definitions installed on the server, except that they have some french added to descriptions and names. Simply copy the xml file of your custom template to the 1036 folder to have it show up as a selection when you select French as the dropdown entry when create a site colleciton. You can go ahead and change the description and name to suit the language it's under.    Second: As part of my site definition, I packaed up several list templates, that were saved as STP files. When you navigate to the list template listing, well, the templates are for English sites, not French so I cannot create document libraries based on the template. What now? well here comes KWIzCom to the rescue! They seem to have put out a "STP language converter" where you can take a site template or list template and convert it to any target language you are after. It's a free download, Use it and you're good to go.  One thing I will mention is that when I convereted the English documents I whent ahead and converted them to French-Canadien. And it didn't work! so I finally figured out that the French Version it was expecting in the french site was "French-France". Don't know why that is, it's just what needs to be done to get that working. When I did that, I was able to use the List templates that I created in the English site for the French Site.   Hope it helps , good luck!

  Read the article

• Connecting Small business network to Azure Site to Site VPN

  - by MarkKGreenway

  Would like to have connectivity between azure virtual machines and on LAN users. My current network has a Cisco ISA550 connected to the WAN (one Ethernet cable into the office the fiber transceiver is on a different floor)and any public servers can be one-to one NAT-ed to have a public and private IP. What is the best way to get a reliable connection. Between end users and the cloud? I want to know the preferred on site endpoint. Do the azure vm's have to have a local ip in the LAN subnet? (Right now 10.10.0.0/20 or 255.255.240.0 to give room if this is the case). If in purchased an asa550 would I put it behind or in front of the isa550. Would it be ahead or peer with the users switches? What is the best way to get a reliable connection. Between end users and the cloud servers?

  Read the article

• WGet or cURL: Mirror Site from http://site.com And No Internal Access

  - by alharaka

  I have tried wget -m wget -r and a whole bunch of variations. I am getting some of the images on http://site.com, one of the scripts, and none of the CSS, even with the fscking -p parameter. The only HTML page is index.html and there are several more referenced, so I am at a loss. curlmirror.pl on the cURL developers website does not seem to get the job done either. Is there something I am missing? I have tried different levels of recursion with only this URL, but I get the feeling I am missing something. Long story short, some school allows its students to submit web projects, but they want to know how they can collect everything for the instructor who will grade it, instead of him going to all the externally hsoted sites.

  Read the article

• How will this affect my SEO ranking?

  - by dunc

  I run a fishkeeping website based on a WordPress (PHP) CMS. I've recently put a fairly complex "filter" into place which searches my content for mentions of fish species profiles and turns them into an active link. For example, asdasd this is a test about abdomen to see if the caudal fin will work asdadasdas try again with abdomen and A. panduro and Apistogramma panduro ...becomes asdasd this is a test about abdomen to see if the caudal fin will work asdadasdas try again with abdomen and <a href="/?p=1703" class="link_species">A. panduro</a> and <a href="/?p=1703" class="link_species">Apistogramma panduro</a> On the rest of my website, the species are linked with pretty URLs such as /species/apistogramma-panduro/ but due to the way this filter works, the only information I can get access to is the idof the post. As such, I'm using /?p=1703 or whatever the ID is. What I'd like to know is: how much will this affect my SEO rating/ranking? Will it be detrimental if I don't rewrite the function? Thanks in advance,

  Read the article

• category title and affect on SEO and ranking [closed]

  - by Mark

  We are working on a jobs and skills website (similiar to Skill Pages) and are deciding on the names of categories. Rather than having loads of categories and sub-categories like, for example, Builder, Electrician, Carpenter etc, we would like to have more general and easier on the eye category names. So for example we have House, Computer, Education, Art etc. So a builder would be in category House and a few others. Will this style negatively effect our SEO and ranking? And if so, should we abandon and go back to traditional categories and sub-categories?

  Read the article

• category title and affect on SEO and ranking

  - by Mark

  We are working on a jobs and skills website (similiar to Skill Pages) and are deciding on categories. Rather than having load of categories like, for example, Builder, Electrician, Carpenter etc, we would like to have one word more general categories. So for example we have House, Computer, Education, Art etc. So a builder would be in category Home and a few others. Will this style negatively effect our SEO and ranking? And if so, should we abandon and go back to traditional categories and sub-categories?

  Read the article

• How to securely enable file sharing over PPTP on Windows 2008 Server

  - by Damage

  I have set up a Windows SBS 2003 domain (LAN) and a stand-alone Windows 2008 Server (web server) at another location (workgroup). I established PPTP VPN connection (SBS dials web server) over which users from LAN should be able to access web server. On web server I enabled TCP/IPv4 and File and Printer sharing protocol. It has a few external addresses (one of them is default) AND one local address (192.x.x.x) assigned to network adapter. Firewall allows port 445 for file sharing. There's the problem - I can not enable web server file shares to be visible to LAN users and ONLY to LAN users: From SBS I can access webserver but I cannot access webserver from LAN workstations (XP, Vista). I have had same configuration - I have just replaced old (web server) Windows 2003 server with 2008 so SBS settings are the same (static route, DNS etc.). How can I enable file sharing on web server for LAN workstations? Now I have opened File and printer sharing to the internet which is of course totaly unsecure. I tried to secure the tunnel so I moved RAS (VPN) connection (Network Center) on web server to "Private" profile and moved firewall port 445 to "Private" profile but suddenly file sharing does not work and I cannot telnet webserver on port 445. How can I secure file sharing so I do not have to open it to the internet?

  Read the article

• VPN IP Routing - slow connections

  - by dannymcc

  UPDATE: Router error logs show: LCP Time-out 0 I'm not sure how to correct this. The Lan-to-Lan profiles are set to -1 Idle Timeout (for the remote branch). I have a PPTP VPN running between two Draytek 2820 routers. They are setup that one dials out to the other one. Main Practice - 192.168.1.0/24 Branch - 192.168.3.0/24 I have then set (on the Branch) router the following route: 192.168.1.0/24 If I then request a server running on 192.168.1.1 from the Branch, it correctly routes through VPN tunnel. If I request the branch server at 192.168.3.1 it correctly routes to the local server without using the VPN tunnel. I have temporarily disabled the firewall on both routers, and made sure that QoS is disabled. The Main Practice internet connection is ~30mb down / ~10mb up, and the Branch connection is ~5mb down / ~2mb up. Anything over the VPN tunnel runs pretty slowly (VNC, Remote Desktop and Terminal Emulators). However, if I dial using the Windows VPN wizard, creating a connection from the laptop to the Main Practice - everything runs quickly. I'm looking for possible causes, and/or ways of further diagnosing the issue. Any help would be greatly appreciated! UPDATE: In summary, when I connect within the Branch and try and access a host that's within the Main Practice it works, but slowly. If I then dial the VPN on my Windows 7 laptop whilst still connected to the Branch network, it's fast. Main Practice Branch Practice Routing Table from Branch Router Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 126.256.126.103 WAN2 C~ 192.168.1.99/ 255.255.255.255 directly connected VPN-1 S~ 192.168.1.0/ 255.255.255.0 via 192.168.1.99 VPN-1 S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.99 VPN-1 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2 C 126.256.126.103/ 255.255.255.224 directly connected WAN2 Routing Table from Main Practice Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 81.139.64.1, WAN2 S 81.137.176.1/ 255.255.255.255 via 81.137.176.1, WAN2 * 81.139.64.1/ 255.255.255.255 via 81.139.64.1, WAN2 C~ 192.168.1.204/ 255.255.255.255 is directly connected, VPN C~ 192.168.1.0/ 255.255.255.0 is directly connected, LAN S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.204, VPN S~ 192.168.3.0/ 255.255.255.0 via 192.168.1.203, VPN Connection Details (from Branch Router) Connection Details (from Main Practice Router) IPERF.exe Output

  Read the article

• Windows server RAS VPN client can't connect to internet

  - by Dragouf

  I configured a windows server 2008 RAS to connect automatically to a pptp vpn server. Problem is that when it connect I can't access internet from this server (the vpn client connect through RAS) Usually I ask vpn not to be use as the default gateway but this part is disable int the network interface - VPN interface properties : And I don't find how to ask to connect to internet directly....

  Read the article

• big speed difference on a network link with and without VPN tunnel

  - by xirtyllo

  Scenario: We have a network link between two offices. The link is provided by a third party company through a VLAN on their network, but to us it is totally transparent -as if we had a simple ethernet cable going from one location to the other-. We have one router at each side of the link, with 3 VPN tunnels in between the two. The test: When I test the speed of the network link with the routers in place, with one laptop directly connected to the router on each side, I consistently get ~30/35Mbps. But if I take out the routers and I test the link connecting the laptops directly to the ethernet cable at each side, I consistently get ~85/88Mbps. It's quite a big performance hit, and I would tend to think that the VPN tunnels are responsible for the slow down. Is it normal that this configuration (two routers with three VPN tunnels between them) takes away so much bandwidth? More info: The encryption algorithm used for the VPN tunnels is AES128. The routers model is Zyxel USG200 and Zyxel USG1000, and their CPU, memory, and storage use is well within normal limits. The nominal bandwidth of the network link is 100Mbps. The network link in question is supplied by a third party company (the building in between our two offices). Basically it passes through their network as a VLAN, but the VLAN is completely transparent to us (e.g. no configuration required on our side, just like one single cable from end to end). Unfortunately (or maybe fortunately) I cannot directly test different routers configurations as I'm not the person in charge of it.

  Read the article

• WGet or cURL: Mirror Site from http://site.com And No Internal Access

  - by alharaka

  I have tried wget -m wget -r and a whole bunch of variations. I am getting some of the images on http://site.com, one of the scripts, and none of the CSS, even with the fscking -p parameter. The only HTML page is index.html and there are several more referenced, so I am at a loss. curlmirror.pl on the cURL developers website does not seem to get the job done either. Is there something I am missing? I have tried different levels of recursion with only this URL, but I get the feeling I am missing something. Long story short, some school allows its students to submit web projects, but they want to know how they can collect everything for the instructor who will grade it, instead of him going to all the externally hsoted sites. UPDATE: I think I figured out the issue. I though the links to the other pages were in the index.html page that downloaded. I was way off. Turns out the footer of the page, which has all the navigation links, is handled by a JavaScript file Include.js, which reads JLSSiteMap.js and some other JS files to do page navigation and the like. As a result, wget does not pick up an other dependencies because a lot of this crap is handled not on web pages. How can I handle such a website? This is one of several problem cases. I assume little can be done if wget cannot parse JavaScript.

  Read the article

• Joining computers to domain when SBS is running in Datacenter

  - by ChrisMuench

  We are contemplating moving our SBS2k8 server to our datacenter. We would be setting up a VPN-VPN tunnel between everything to handle AD. Has anyone done this before? Any particular issues that anyone can remember? So the flow for AD would now become. SBS<-VPN---VPN<-Internal office network

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >