Search Results

Search found 28170 results on 1127 pages for '16 bit animation'.

Page 90/1127 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

  • 2560 x 1600 screen resolution not available when a second monitor is attached.

    - by sgmoore
    I am running Windows 7 (64-bit edition) and have a 30" Dell 3007WFP monitor which runs at a screen resolution of 2560 x 1600. This works perfectly until I try to connect a second monitor, and then the screen resolution on the main monitor immediately drops to 1280x800 and I can't change it back up to the correct resolution until I disconnect the second monitor. The graphics card is a Nvidia Quadro FX 370. This has a dual link DVI connector (to which the 30" is connected) and a single link DVI connector. The second monitor can run at 1920x1080 and is connected using a VGA to DVI connector. Note, it does not seem to matter whether the second monitor is running at 1920x1080 or even at 800x600. Windows reports Total Available Graphics Memory: 3839MB Dedicated Video Memory: 256MB System Video Memory: 0MB Shared System Memory: 3583MB Does anyone know if this a limitation with the video card, memory, drivers, connectors or something else? If this is a limitation with the video card, can anyone recommend a PCI Express 16 card that would support at least this setup, but preferably support two 30" monitors both running 2560 x 1600. (I'm not into gaming etc, so it doesn't need to be very powerful)

    Read the article

  • How to install ia32-libs on Wheezy?

    - by javano
    I have seen a couple of questions on ServerFault relating to installing ia32-libs on a 64bit machine but the solutions aren't working for me (I don't think any of these questions where for Wheezy specifically I'm not sure how to proceed); root@server:/home/# apt-get install -f ia32-libs Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 php5 : Depends: libapache2-mod-php5 (>= 5.4.4-14+deb7u2) but it is not going to be installed or libapache2-mod-php5filter (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-cgi (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-fpm (>= 5.4.4-14+deb7u2) but it is not going to be installed php5-mysql : Depends: phpapi-20100525 E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. root@server:/home/# sudo apt-get install ia32-libs-i386 Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs-i386:i386 : Depends: freeglut3:i386 (>= 2.6.0-1) but it is not going to be installed Depends: lesstif2:i386 (>= 1:0.95.2-1) but it is not going to be installed Depends: libacl1:i386 (>= 2.2.49-4) but it is not going to be installed Depends: libasyncns0:i386 (>= 0.3-1.1) but it is not going to be installed Depends: libattr1:i386 (>= 1:2.4.44-2) but it is not going to be installed Depends: libaudio2:i386 (>= 1.9.2-4) but it is not going to be installed Depends: libaudiofile1:i386 (>= 0.2.6-8) but it is not going to be installed Depends: libavahi-client3:i386 (>= 0.6.27-2+squeeze1) but it is not going to be installed Depends: libavahi-common3:i386 (>= 0.6.27-2+squeeze1) but it is not going to be installed Depends: libbsd0:i386 (>= 0.2.0-1) but it is not going to be installed Depends: libcap2:i386 (>= 1:2.19-3) but it is not going to be installed Depends: libcomerr2:i386 (>= 1.41.12-4stable1) but it is not going to be installed Depends: libcups2:i386 (>= 1.4.4-7+squeeze1) but it is not going to be installed Depends: libcurl3:i386 (>= 7.21.0-2) but it is not going to be installed Depends: libdbus-1-3:i386 (>= 1.2.24-4+squeeze1) but it is not going to be installed Depends: libdirectfb-1.2-9:i386 (>= 1.2.10.0-4) but it is not going to be installed Depends: libdrm-intel1:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libdrm-radeon1:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libdrm2:i386 (>= 2.4.21-1~squeeze3) but it is not going to be installed Depends: libedit2:i386 (>= 2.11-20080614-2) but it is not going to be installed Depends: libesd0:i386 (>= 0.2.41-8) but it is not going to be installed Depends: libexif12:i386 (>= 0.6.19-1) but it is not going to be installed Depends: libexpat1:i386 (>= 2.0.1-7) but it is not going to be installed Depends: libflac8:i386 (>= 1.2.1-2+b1) but it is not going to be installed Depends: libfltk1.1:i386 (>= 1.1.10-2+b1) but it is not going to be installed Depends: libfontconfig1:i386 (>= 2.8.0-2.1) but it is not going to be installed Depends: libfreetype6:i386 (>= 2.4.2-2.1+squeeze3) but it is not going to be installed Depends: libgcrypt11:i386 (>= 1.4.5-2) but it is not going to be installed Depends: libgdbm3:i386 (>= 1.8.3-9) but it is not going to be installed Depends: libgl1-mesa-dri:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libgl1-mesa-glx:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libglu1-mesa:i386 (>= 7.7.1-5) but it is not going to be installed Depends: libgnutls26:i386 (>= 2.8.6-1) but it is not going to be installed Depends: libgpg-error0:i386 (>= 1.6-1) but it is not going to be installed Depends: libgphoto2-2:i386 (>= 2.4.6-3) but it is not going to be installed Depends: libgphoto2-port0:i386 (>= 2.4.6-3) but it is not going to be installed Depends: libgssapi-krb5-2:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libice6:i386 (>= 2:1.0.6-2) but it is not going to be installed Depends: libidn11:i386 (>= 1.15-2) but it is not going to be installed Depends: libieee1284-3:i386 (>= 0.2.11-6) but it is not going to be installed Depends: libjack-jackd2-0:i386 (>= 1.9.5~dfsg-14) but it is not going to be installed or libjack0:i386 (>= 1:0.118+svn3796-7) but it is not going to be installed Depends: libjpeg62:i386 (>= 6b1-1) but it is not going to be installed Depends: libjpeg8:i386 (>= 8b-1) but it is not going to be installed Depends: libk5crypto3:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libkeyutils1:i386 (>= 1.4-1) but it is not going to be installed Depends: libkrb5-3:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: libkrb5support0:i386 (>= 1.8.3+dfsg-4squeeze2) but it is not going to be installed Depends: liblcms1:i386 (>= 1.18.dfsg-1.2+b3) but it is not going to be installed Depends: libltdl7:i386 (>= 2.2.6b-2) but it is not going to be installed Depends: liblzo2-2:i386 (>= 2.03-2) but it is not going to be installed Depends: libmpg123-0:i386 (>= 1.12.1-3) but it is not going to be installed Depends: libnspr4-0d:i386 (>= 4.8.6-1) but it is not going to be installed Depends: libnss3-1d:i386 (>= 3.12.8-1+squeeze4) but it is not going to be installed Depends: libogg0:i386 (>= 1.2.0~dfsg-1) but it is not going to be installed Depends: libopenal1:i386 (>= 1:1.12.854-2) but it is not going to be installed Depends: libpam0g:i386 (>= 1.1.1-6.1+squeeze1) but it is not going to be installed Depends: libpng12-0:i386 (>= 1.2.44-1+squeeze1) but it is not going to be installed Depends: libpopt0:i386 (>= 1.16-1) but it is not going to be installed Depends: libpulse0:i386 (>= 0.9.21-3+squeeze1) but it is not going to be installed Depends: libsamplerate0:i386 (>= 0.1.7-3) but it is not going to be installed Depends: libsane:i386 (>= 1.0.21-9) but it is not going to be installed Depends: libsasl2-2:i386 (>= 2.1.23.dfsg1-7) but it is not going to be installed Depends: libsdl1.2debian:i386 (>= 1.2.15) but it is not going to be installed Depends: libselinux1:i386 (>= 2.0.96-1) but it is not going to be installed Depends: libsigc++-2.0-0c2a:i386 (>= 2.2.4.2-1) but it is not going to be installed Depends: libsm6:i386 (>= 2:1.1.1-1) but it is not going to be installed Depends: libsndfile1:i386 (>= 1.0.21-3+squeeze1) but it is not going to be installed Depends: libsqlite3-0:i386 (>= 3.7.3-1) but it is not going to be installed Depends: libssh2-1:i386 (>= 1.2.6-1) but it is not going to be installed Depends: libssl1.0.0:i386 (>= 1) but it is not going to be installed Depends: libstdc++5:i386 (>= 1:3.3.6-20) but it is not going to be installed Depends: libsvga1:i386 (>= 1:1.4.3-29) but it is not going to be installed Depends: libsysfs2:i386 (>= 2.1.0+repack-1) but it is not going to be installed Depends: libtasn1-3:i386 (>= 2.7-1) but it is not going to be installed Depends: libtdb1:i386 (>= 1.2.1-2+b1) but it is not going to be installed Depends: libtiff4:i386 (>= 3.9.4-5+squeeze3) but it is not going to be installed Depends: libts-0.0-0:i386 (>= 1.0-7) but it is not going to be installed Depends: libusb-0.1-4:i386 (>= 2:0.1.12-16) but it is not going to be installed Depends: libuuid1:i386 (>= 2.17.2-9) but it is not going to be installed Depends: libvorbis0a:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libvorbisenc2:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libvorbisfile3:i386 (>= 1.3.1-1) but it is not going to be installed Depends: libwrap0:i386 (>= 7.6.q-19) but it is not going to be installed Depends: libx11-6:i386 (>= 2:1.3.3-4) but it is not going to be installed Depends: libx86-1:i386 (>= 1.1+ds1-6) but it is not going to be installed Depends: libxau6:i386 (>= 1:1.0.6-1) but it is not going to be installed Depends: libxaw7:i386 (>= 2:1.0.7-1) but it is not going to be installed Depends: libxcb-render-util0:i386 (>= 0.3.6-1) but it is not going to be installed Depends: libxcb-render0:i386 (>= 1.6-1) but it is not going to be installed Depends: libxcb1:i386 (>= 1.6-1) but it is not going to be installed Depends: libxcomposite1:i386 (>= 1:0.4.2-1) but it is not going to be installed Depends: libxcursor1:i386 (>= 1:1.1.10-2) but it is not going to be installed Depends: libxdamage1:i386 (>= 1:1.1.3-1) but it is not going to be installed Depends: libxdmcp6:i386 (>= 1:1.0.3-2) but it is not going to be installed Depends: libxext6:i386 (>= 2:1.1.2-1) but it is not going to be installed Depends: libxfixes3:i386 (>= 1:4.0.5-1) but it is not going to be installed Depends: libxft2:i386 (>= 2.1.14-2) but it is not going to be installed Depends: libxi6:i386 (>= 2:1.3-6) but it is not going to be installed Depends: libxinerama1:i386 (>= 2:1.1-3) but it is not going to be installed Depends: libxml2:i386 (>= 2.7.8.dfsg-2+squeeze1) but it is not going to be installed Depends: libxmu6:i386 (>= 2:1.0.5-2) but it is not going to be installed Depends: libxmuu1:i386 (>= 2:1.0.5-2) but it is not going to be installed Depends: libxp6:i386 (>= 1:1.0.0.xsf1-2) but it is not going to be installed Depends: libxpm4:i386 (>= 1:3.5.8-1) but it is not going to be installed Depends: libxrandr2:i386 (>= 2:1.3.0-3) but it is not going to be installed Depends: libxrender1:i386 (>= 1:0.9.6-1) but it is not going to be installed Depends: libxslt1.1:i386 (>= 1.1.26-6) but it is not going to be installed Depends: libxss1:i386 (>= 1:1.2.0-2) but it is not going to be installed Depends: libxt6:i386 (>= 1:1.0.7-1) but it is not going to be installed Depends: libxtst6:i386 (>= 2:1.1.0-3) but it is not going to be installed Depends: libxv1:i386 (>= 2:1.0.5-1) but it is not going to be installed Depends: libxxf86vm1:i386 (>= 1:1.1.0-2) but it is not going to be installed Depends: odbcinst1debian2:i386 (>= 2.2.14p2-1) but it is not going to be installed Depends: libodbc1:i386 but it is not going to be installed Depends: xaw3dg:i386 (>= 1.5+E-18) but it is not going to be installed php5 : Depends: libapache2-mod-php5 (>= 5.4.4-14+deb7u2) but it is not going to be installed or libapache2-mod-php5filter (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-cgi (>= 5.4.4-14+deb7u2) but it is not going to be installed or php5-fpm (>= 5.4.4-14+deb7u2) but it is not going to be installed php5-mysql : Depends: phpapi-20100525 E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. root@server:/home/# dpkg --print-architecture amd64 root@server:/home/# dpkg --print-foreign-architectures i386 root@server:/home/# lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 7.1 (wheezy) Release: 7.1 Codename: wheezy root@server:/home/# uname -a Linux servername 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux root@server:/home/# cat /etc/apt/sources.list deb http://ftp.us.debian.org/debian stable main contrib non-free

    Read the article

  • Some Apps don't start on Windows 8 Release Preview

    - by Exa
    I recently installed the Release Preview of Windows 8 in a virtual machine. Some apps do not work. When I open them (by clicking on their tile in the start screen) I see a splash screen and nothing else happens. Sometimes the app crashes after 30 seconds, sometimes it just keeps on loading. A good example is the "Map"-App from Windows 8 or the app "Cookbook" by Bewise. I installed Cookbook and when I had a look at the task manager I saw that it was the 32bit version running, but I have an x64 Windows 8... Could this be a problem? Shouldn't the Windows Store download the correct version? This is the setup of my virtual machine: Windows 8 Release Preview x64 Oracle VirtualBox 4 of 8 cores from host system 8 of 16 GB RAM from the host system 256 MB graphics memory guest additions installed resolution 1920 x 1080 Do you need further information? Unfortunately there is no error message... I just see the start screen of the app with its logo and it keeps loading, but nothing happens. Other Apps (like Mail, Video, Social, etc.) work fine.

    Read the article

  • scale animation for wpf popup

    - by wpf
    I have a nice little popup, when it shows, I d'like it to growth from 0 to 1x scaley, but I don't get it right, when I click multiple times, it looks like i "catch" the animation at various states during the "growth". <Window.Triggers> <EventTrigger RoutedEvent="FrameworkElement.MouseRightButtonDown" > <EventTrigger.Actions> <BeginStoryboard> <Storyboard> <DoubleAnimationUsingKeyFrames BeginTime="00:00:00" Storyboard.TargetName="SimplePopup" Storyboard.TargetProperty="(FrameworkElement.LayoutTransform).(TransformGroup.Children)[0].(ScaleTransform.ScaleY)"> <SplineDoubleKeyFrame KeyTime="00:00:00" Value="0"/> <SplineDoubleKeyFrame KeyTime="00:00:00.3000000" Value="1"/> </DoubleAnimationUsingKeyFrames> </Storyboard> </BeginStoryboard> </EventTrigger.Actions> </EventTrigger> </Window.Triggers> and the popup: <Popup Name="SimplePopup" AllowsTransparency="True" StaysOpen="False"> <Popup.LayoutTransform> <TransformGroup> <ScaleTransform ScaleX="1" ScaleY="1" /> <SkewTransform AngleX="0" AngleY="0" /> <RotateTransform Angle="0" /> <TranslateTransform X="0" Y="0" /> </TransformGroup> </Popup.LayoutTransform> <Border> some Content here </Border> </Popup>

    Read the article

  • [iPhone] Background color during flip view animation/transition?

    - by Rob S.
    I have some pretty standing flipping action going on: [UIView beginAnimations:@"swapScreens" context:nil]; [UIView setAnimationTransition:UIViewAnimationTransitionFlipFromLeft forView:self.view cache:YES]; [UIView setAnimationDuration:1.0]; [self.view exchangeSubviewAtIndex:0 withSubviewAtIndex:1]; [UIView commitAnimations]; To Apple's credit, this style of animation is amazingly easy to work with. Very cool, and I've been able to animate transitions, flips, fades etc. throughout the app very easily. Question: During the flip transition, the background visible 'behind' the two views during the flip is white and I'd like it to be black. I've: Set the background of the containing view (self.view above) - no dice. I really thought that would work. Set the background of each view to black - no dice. I didn't think this would work although you give different things a shot to understand better :) Google'd like crazy; keep landing on Safari-related listings. Thanks in advance!

    Read the article

  • Image animation over CGContextDrawPDFPage

    - by BittenApple
    I'm modifying the QuartzDemo sample app from Apple. In QuartzViewController.m I have modifications (by DyingCactus) which replac the back button and add a method to handle the back button press as follows: -(void)viewDidLoad { // Add the QuartzView [scrollView addSubview:self.quartzView]; //add custom back button if this is the PDF view... if ([self.quartzView isKindOfClass:[QuartzPDFView class]]) { self.navigationItem.leftBarButtonItem = [[UIBarButtonItem alloc] initWithTitle:@"QuartzDemo" style:UIBarButtonItemStyleBordered target:self action:@selector(myBackButtonHandler:)]; } } - (void)myBackButtonHandler:(id)sender { [self.quartzView setFrame:CGRectMake(150, -200, 100, 200)]; [UIView beginAnimations:nil context:nil]; [UIView setAnimationDelegate:self]; [UIView setAnimationDidStopSelector:@selector(animationDidStop:finished:context:)]; [UIView setAnimationDuration:1.0]; [self.quartzView setFrame:CGRectMake(150, 0, 100, 200)]; [UIView commitAnimations]; } - (void)animationDidStop:(NSString *)animationID finished:(NSNumber *)finished context:(void *)context { [self.navigationController popViewControllerAnimated:YES]; } I have a PNG image in resources folder called "bookmark.png" and would like to have that image animate as in animation in the example above. The image can be loaded in an UImageview or something and lets say that I have one called bookmark. How do I call that instead of self.quartzview in this part of code: [self.quartzView setFrame:CGRectMake(150, -200, 100, 200)]; [UIView beginAnimations:nil context:nil]; [UIView setAnimationDelegate:self]; [UIView setAnimationDidStopSelector:@selector(animationDidStop:finished:context:)]; [UIView setAnimationDuration:1.0]; [self.quartzView setFrame:CGRectMake(150, 0, 100, 200)]; [UIView commitAnimations];

    Read the article

  • Stall in animation

    - by tech74
    Hi , I am using this code from this site http://ramin.firoozye.com/2009/09/29/semi-modal-transparent-dialogs-on-the-iphone/ to show a modal view and remove it. It displays fine ie drops in from the top but when being removed it stalls just on its way out just for a fraction of second but its noticeable how do i get rid of the stall. The view i am showing is view of a viewcontroller which is a memeber of the parent viewcontroller so i call methods like this to display [self showModal:self.modalController.view] to hide [self hideModal:self.modalController.view]; (void) showModal:(UIView*) modalView { UIWindow* mainWindow = (((SessionTalkAppDelegate*) [UIApplication sharedApplication].delegate).window); //CGPoint middleCenter = modalView.center; CGPoint middleCenter = CGPointMake(160, 205); CGSize offSize = [UIScreen mainScreen].bounds.size; //CGPoint offScreenCenter = CGPointMake(offSize.width / 2.0, offSize.height * 1.5); CGPoint offScreenCenter = CGPointMake(offSize.width / 2.0, -100); // start from top modalView.center = offScreenCenter; // we start off-screen [mainWindow addSubview:modalView]; // Show it with a transition effect [UIView beginAnimations:nil context:nil]; [UIView setAnimationDuration:0.3]; // animation duration in seconds [UIView setAnimationCurve:UIViewAnimationCurveEaseInOut]; modalView.center = middleCenter; [UIView commitAnimations]; } // Use this to slide the semi-modal back up. - (void) hideModal:(UIView*) modalView { CGSize offSize = [UIScreen mainScreen].bounds.size; //CGPoint offScreenCenter = CGPointMake(offSize.width / 2.0, offSize.height * 1.5); CGPoint offScreenCenter = CGPointMake(offSize.width / 2.0, -100); [UIView beginAnimations:nil context:modalView]; [UIView setAnimationDuration:0.3]; [UIView setAnimationCurve:UIViewAnimationCurveEaseInOut]; [UIView setAnimationDelegate:self]; [UIView setAnimationDidStopSelector:@selector(hideModalEnded:finished:context:)]; modalView.center = offScreenCenter; [UIView commitAnimations]; } (void) hideModalEnded:(NSString *)animationID finished:(NSNumber *)finished context:(void )context { UIView modalView = (UIView *)context; [modalView removeFromSuperview]; //[modalView release]; }

    Read the article

  • Browser: Continue gif animation after escape is pressed

    - by cottsak
    Firefox (and other browsers i believe) stop gif animation when you click the Stop button or invoke it via the Escape key. I have a text input that on change makes ajax requests to update other elements. As part of this ajaxyness i have an animated gif to show feedback. I also trap the escape key press in this input so as to clear the text field for better UX. My problem is after the escape key is pressed once, none of the ajax gifs animate anymore until the page is refreshed. Does anyone know a workaround? Stuff i've tried: I tried the e.stopPropagation(); and e.cancelBubble = true; in the function handling the e.keyCode == 27 and that didn't seem to work. I suspect that this stops trigging more js events and the browser catches the escape irrespective of js activity. I have the gif showing/hiding via adding/removing a css class so it's difficult to apply the "change gif url to reset" workaround. I dont even know if this works anyway - didn't test it. But it seems difficult. If anyone knows that this works and knows of an easy way to apply the hack with background-image: url(../images/ajax-loader_dotcirclel13x13.gif); css then please let me know.

    Read the article

  • NSOperation for animation loop causes strange scrolling behaviour

    - by Tricky
    Hi, I've created an animation loop which I run as an operation in order to keep the rest of my interface responsive. Whilst almost there, there is still one remaining issue. My UIScrollViews don't seem to be reliably picking up when a user touch ends. What this means is, for example, if a user drags down on a scroll view, when they lift their fingers the scrollview doesn't bounce back into place and the scrollbar remains visible. As if the finger hasn't left the screen. It takes another tap on the scrollview for it to snap to its correct position and the scrollbar to fade away... Here's the loop I created in a subclassed NSOperation: (void)main { NSAutoreleasePool *pool = [[NSAutoreleasePool alloc] init]; NSRunLoop *runLoop = [NSRunLoop currentRunLoop]; _displayLink = [[CADisplayLink displayLinkWithTarget: self selector: @selector(animationLoop:)] retain]; [_displayLink setFrameInterval: 1.0f]; [_displayLink addToRunLoop:[NSRunLoop currentRunLoop] forMode: NSRunLoopCommonModes]; while (![self isCancelled]) { NSAutoreleasePool *loopPool = [[NSAutoreleasePool alloc] init]; [runLoop runMode:NSDefaultRunLoopMode beforeDate:[NSDate distantFuture]]; [loopPool drain]; } [_displayLink invalidate]; [pool release]; } DOes anyone have any idea what might be going on here, and even better how to fix it... Thanks!

    Read the article

  • Continue gif animation after escape is pressed

    - by cottsak
    Firefox (and other browsers i believe) stop gif animation when you click the Stop button or invoke it via the Escape key. I have a text input that on change makes ajax requests to update other elements. As part of this ajaxyness i have an animated gif to show feedback. I also trap the escape key press in this input so as to clear the text field for better UX. My problem is after the escape key is pressed once, none of the ajax gifs animate anymore until the page is refreshed. Does anyone know a workaround? Stuff i've tried: I tried the e.stopPropagation(); and e.cancelBubble = true; in the function handling the e.keyCode == 27 and that didn't seem to work. I suspect that this stops trigging more js events and the browser catches the escape irrespective of js activity. I have the gif showing/hiding via adding/removing a css class so it's difficult to apply the "change gif url to reset" workaround. I dont even know if this works anyway - didn't test it. But it seems difficult. If anyone knows that this works and knows of an easy way to apply the hack with background-image: url(../images/ajax-loader_dotcirclel13x13.gif); css then please let me know.

    Read the article

  • Converting Single dimensional vector or array to two dimension in Matlab

    - by pac
    Well I do not know if I used the exact term. I tried to find an answer on the net. Here is what i need: I have a vector a = 1 4 7 2 5 8 3 6 9 If I do a(4) the value is 4. So it is reading first column top to buttom then continuing to next .... I don't know why. However, What I need is to call it using two indices. As row and column: a(3,2)= 4 or even better if i can call it in the following way: a{3}(2)=4 What is this process really called (want to learn) and how to perform in matlab. I thought of a loop. Is there a built in function Thanks a lot Check this: a = 18 18 16 18 18 18 16 0 0 0 16 16 18 0 18 16 0 18 18 16 18 0 18 18 0 16 0 0 0 18 18 0 18 18 16 0 16 0 18 18 >> a(4) ans = 18 >> a(5) ans = 18 >> a(10) ans = 18 I tried reshape. it is reshaping not converting into 2 indeces

    Read the article

  • Stop animation on last element

    - by littleMan
    I have a sliding panel and on the last element I want the animation to stop i've tried using the .is(':last') and it doesn't stop. here is my code. the current var is set to the first element when the form loads. It animates to the left and keeps animating when you click the next button i just want to stop it on the last element jQuery('.wikiform .navigation input[name^=Next]').click(function () { if (current.is(':last')) return; jQuery('.wikiform .wizard').animate({ marginLeft: '-=' + current.width() + "px" }, 750); current = current.next();}); <div id="formView1" class="wikiform"> <div class="wizard"> <div id="view1" class="view"> <div class="form"> Content 1 </div> </div> <div id="view2" class="view"> <div class="form"> Content 2 </div> </div> </div> <div class="navigation"> <input type="button" name="Back" value=" Back " /> <input type="button" name="Next " class="Next" value=" Next " /> <input type="button" name="Cancel" value="Cancel" /> </div> </div>

    Read the article

  • Drawing animation

    - by HHHH
    I'm creating a simple app where when the user presses a button, a series of lines will be drawn on the screen and the user will be able to see these lines drawn in real time (almost like an animation). My code looks something like this (has been simplified): UIGraphicsBeginImageContext(CGSizeMake(300,300)); CGContextRef context = UIGraphicsGetCurrentContext(); for (int i = 0; i < 100; i++ ) { CGContextMoveToPoint(context, i, i); CGContextAddLineToPoint(context, i+20, i+20); CGContextSetStrokeColorWithColor(context, [[UIColor blackColor] CGColor]); CGContextStrokePath(context); } UIImage *newImage = UIGraphicsGetImageFromCurrentImageContext(); UIGraphicsEndImageContext(); My problem is that: 1) As soon as the user presses the button, the UIThread blocks until the drawing is done. 2) I can't get the lines to be drawn on the screen one at a time - I've tried setting the UIImage directly inside the loop and also tried setting a layer content inside the loop. How do I get around these problems?

    Read the article

  • sendmail can not relay from itself

    - by Bernie
    I am running 3 centos 5.2 servers and I have configured the server for forward all messages to root to be emailed to me via .forward rule. This is working fine on two of the servers but not on the third. I have also tried copying the mail config files from the backup server and placing them on the file server and restarting sendmail. I also removed and reinstalled sendmail via yum but the results are the same. I am not sure what the issue could be they are all standard centos installs. Here is an example from the backup server which is working and the fileserver which isn't I am also going to include the mail log. good from backup server [root@backup ]# sendmail -v [email protected] < test.mail [email protected]... Connecting to [127.0.0.1] via relay... 220 backup.localhost ESMTP Sendmail 8.13.8/8.13.8; Fri, 16 Oct 2009 10:23:50 -0700 >>> EHLO backup.localhost 250-backup.localhost Hello backup.localhost [127.0.0.1], pleased to meet you 250-ENHANCEDSTATUSCODES 250-PIPELINING 250-8BITMIME 250-SIZE 250-DSN 250-ETRN 250-DELIVERBY 250 HELP >>> MAIL From:<[email protected]> SIZE=73 250 2.1.0 <[email protected]>... Sender ok >>> RCPT To:<[email protected]> >>> DATA 250 2.1.5 <[email protected]>... Recipient ok 354 Enter mail, end with "." on a line by itself >>> . 250 2.0.0 n9GHNoGC020924 Message accepted for delivery [email protected]... Sent (n9GHNoGC020924 Message accepted for delivery) Closing connection to [127.0.0.1] >>> QUIT 221 2.0.0 backup.localhost closing connection bad from file server [root@fileserver bernie]# sendmail -v [email protected] < test.mail [email protected]... Connecting to [127.0.0.1] via relay... 220 fileserver.localhost ESMTP Sendmail 8.13.8/8.13.8; Fri, 16 Oct 2009 10:23:26 -0700 >>> EHLO fileserver.localhost 250-fileserver.localhost Hello fileserver.localhost [127.0.0.1], pleased to meet you 250 ENHANCEDSTATUSCODES >>> MAIL From:<[email protected]> 550 5.0.0 Access denied root... Using cached ESMTP connection to [127.0.0.1] via relay... >>> RSET 250 2.0.0 Reset state >>> MAIL From:<> 550 5.0.0 Access denied postmaster... Using cached ESMTP connection to [127.0.0.1] via relay... >>> RSET 250 2.0.0 Reset state >>> MAIL From:<> 550 5.0.0 Access denied Closing connection to [127.0.0.1] >>> QUIT 221 2.0.0 fileserver.localhost closing connection mail log Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: from=root, size=72, class=0, nrcpts=1, msgid=<[email protected]>, relay=root@localhost Oct 16 10:39:13 fileserver sendmail[28060]: n9GHdDwl028060: tcpwrappers (fileserver.localhost, 127.0.0.1) rejection Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: [email protected], ctladdr=root (0/0), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30072, relay=[127.0.0.1] [127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDom028059: n9GHdDon028059: DSN: Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: to=root, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=31096, relay=[127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: n9GHdDoo028059: return to sender: Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDoo028059: to=postmaster, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=32120, relay=[127.0.0.1], dsn=5.0.0, stat=Service unavailable Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: Losing ./qfn9GHdDon028059: savemail panic Oct 16 10:39:13 fileserver sendmail[28059]: n9GHdDon028059: SYSERR(root): savemail: cannot save rejected email anywhere

    Read the article

  • Is Visual Studio 2010 WebDev WebServer (Cassini) 64-bit compatible?

    - by David
    I'm now developing on Visual Studio 2008 on a 64-bit OS (Windows Server 2008 64-bit). While the apps I write are 64-bit capable, as is IIS7, the built-in ASP.NET Development Server (aka Cassini aka WebDev.Webserver.exe) runs as 32-bit. This brings up a plethora of issues, such as: 32-bit and 64-bit applications have separate HKLM\Software registry homes There are 32-bit and 64-bit versions of the SQL Server Client Network Utility Other fun surprises I haven't discovered but I'm sure will spring up While I am finding workarounds for most of this, I have to ask... Does anyone who has played with the Visual Studio 2010 preview bits on 64-bit architecture know if the development web servers can handle 64-bit, and if so, are there options for which mode to run it in? (Like a checkbox in the project properties, for instance)

    Read the article

  • Vagrant (Virtualbox) host-only multiple node networking issue

    - by Lorin Hochstein
    I'm trying to use a multi-VM vagrant environment as a testbed for deploying OpenStack, and I've run into a networking problem with trying to communicate from one VM, to a VM-inside-of-a-VM. I have two Vagrant nodes, a cloud controller node and a compute node. I'm using host-only networking. My Vagrantfile looks like this: Vagrant::Config.run do |config| config.vm.box = "precise64" config.vm.define :controller do |controller_config| controller_config.vm.network :hostonly, "192.168.206.130" # eth1 controller_config.vm.network :hostonly, "192.168.100.130" # eth2 controller_config.vm.host_name = "controller" end config.vm.define :compute1 do |compute1_config| compute1_config.vm.network :hostonly, "192.168.206.131" # eth1 compute1_config.vm.network :hostonly, "192.168.100.131" # eth2 compute1_config.vm.host_name = "compute1" compute1_config.vm.customize ["modifyvm", :id, "--memory", 1024] end end When I try to start up a (QEMU-based) VM, it boots successfully on compute1, and its virtual nic (vnet0) is connected via a bridge, br100: root@compute1:~# brctl show 100 bridge name bridge id STP enabled interfaces br100 8000.08002798c6ef no eth2 vnet0 When the QEMU VM makes a request to the DHCP server (dnsmasq) running on controller, I can see the request reaches the controller because of the output on the syslog on the controller: Aug 6 02:34:56 precise64 dnsmasq-dhcp[12042]: DHCPDISCOVER(br100) fa:16:3e:07:98:11 Aug 6 02:34:56 precise64 dnsmasq-dhcp[12042]: DHCPOFFER(br100) 192.168.100.2 fa:16:3e:07:98:11 However, the DHCPOFFER never makes it back to the VM running on compute1. If I watch the requests using tcpdump on the vboxnet3 interface on my host machine that runs Vagrant (Mac OS X), I can see both the requests and the replies $ sudo tcpdump -i vboxnet3 -n port 67 or port 68 tcpdump: WARNING: vboxnet3: That device doesn't support promiscuous mode (BIOCPROMISC: Operation not supported on socket) tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vboxnet3, link-type EN10MB (Ethernet), capture size 65535 bytes 22:51:20.694040 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:20.694057 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:20.696047 IP 192.168.100.1.67 > 192.168.100.2.68: BOOTP/DHCP, Reply, length 311 22:51:23.700845 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:23.700876 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:23.701591 IP 192.168.100.1.67 > 192.168.100.2.68: BOOTP/DHCP, Reply, length 311 22:51:26.705978 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:26.705995 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:26.706527 IP 192.168.100.1.67 > 192.168.100.2.68: BOOTP/DHCP, Reply, length 311 But, if I tcpdump on eth2 on compute, I only see the requests, not the replies: root@compute1:~# tcpdump -i eth2 -n port 67 or port 68 tcpdump: WARNING: eth2: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth2, link-type EN10MB (Ethernet), capture size 65535 bytes 02:51:20.240672 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 02:51:23.249758 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 02:51:26.258281 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 At this point, I'm stuck. I'm not sure why the DHCP replies aren't making it to the compute node. Perhaps it has something to do with the configuration of the VirtualBox virtual switch/router? Note that eth2 interfaces on both nodes have been set to promiscuous mode.

    Read the article

  • Why does copying an XML file from Windows Server 2008 R2 64-bit to Windows XP 32-bit change the file?

    - by Alex In Paris
    What I do: Copy an xml file (ctrl+C) on a Win Server 2008 machine. Minimize mstsc.exe (remote connection app). Paste the xml file on to my WinXP machine (ctrl+V). The result: All of the original contents are still present but another bit is appended at the end of it. E.g. the proper end of the file looks something like this: <ApplicationName>MyApp</ApplicationName> </ReceivePort> </ReceivePortCollection> <PartyCollection xsi:nil="true" /> </BindingInfo> But, after the copy, it looks like this: <ApplicationName>MyApp</ApplicationName> </ReceivePort> </ReceivePortCollection> <PartyCollection xsi:nil="true" /> </BindingInfo>al, PublicKeyToken=3zzf3xxxadyyy35" Type="1" TrackingOption="ServiceStartEnd MessageSendReceive PipelineEvents" Description="" /> <ReceivePipelineData xsi:nil="true" /> <SendPipeline xsi:nil="true" /> <SendPipelineData xsi:nil="true" /> <Enable>true</Enable> <ReceiveHandler Name="WCF_OracleDB_Rx" HostTrusted="false"> <TransportType Name="WCF OracleDB" Capabilities="779" Configuratio The extra bits it adds are things that come from earlier in the XML file. If I do the copy multiple times, the extra bits are always exactly the same but another XML file will add different lines. Extra information: If I copy/paste the file, as above, but first enclose it into a zip file I do not have the same problem. I.e. the file copies properly and without any extra surprises. If I do a copy/paste from a Windows Explorer window that's opened to the folder on the remote machine, I do not have the same behavior. I.e. the file copies properly and without any extra surprises. Question: Why does this happen?

    Read the article

  • Why is it useful to count the number of bits?

    - by Scorchin
    I've seen the numerous questions about counting the number of set bits in a insert type of input, but why is it useful? For those looking for algorithms about bit counting, look here: http://stackoverflow.com/questions/1517848/counting-common-bits-in-a-sequence-of-unsigned-longs http://stackoverflow.com/questions/472325/fastest-way-to-count-number-of-bit-transitions-in-an-unsigned-int http://stackoverflow.com/questions/109023/best-algorithm-to-count-the-number-of-set-bits-in-a-32-bit-integer

    Read the article

  • i cant ping to my DMZ zone from the local inside PC

    - by Big Denzel
    HI everybody. Can anyone please help me on the following issue. I got a Cisco Asa 5520 configured at my network. I cant ping to my DMZ interface from a local inside network PC. so the only way a ping the DMZ is right from the Cisco ASA firewall, there i can pint to all 3 interfaces, Inside, Outside and DMZ,,,, But no PC from the Inside Network can access the DMZ. Can please any one help? I thank you all in advance Bellow is my Cisco ASA 5520 Firewall show run; ASA-FW# sh run : Saved : ASA Version 7.0(8) ! hostname ASA-FW enable password encrypted passwd encrypted names dns-guard ! interface GigabitEthernet0/0 description "Link-To-GW-Router" nameif outside security-level 0 ip address 41.223.156.109 255.255.255.248 ! interface GigabitEthernet0/1 description "Link-To-Local-LAN" nameif inside security-level 100 ip address 10.1.4.1 255.255.252.0 ! interface GigabitEthernet0/2 description "Link-To-DMZ" nameif dmz security-level 50 ip address 172.16.16.1 255.255.255.0 ! interface GigabitEthernet0/3 shutdown no nameif no security-level no ip address ! interface Management0/0 description "Local-Management-Interface" no nameif no security-level ip address 192.168.192.1 255.255.255.0 ! ftp mode passive access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.107 eq smtp access-list OUT-TO-DMZ extended permit tcp any host 41.223.156.106 eq www access-list OUT-TO-DMZ extended permit icmp any any log access-list OUT-TO-DMZ extended deny ip any any access-list inside extended permit tcp any any eq pop3 access-list inside extended permit tcp any any eq smtp access-list inside extended permit tcp any any eq ssh access-list inside extended permit tcp any any eq telnet access-list inside extended permit tcp any any eq https access-list inside extended permit udp any any eq domain access-list inside extended permit tcp any any eq domain access-list inside extended permit tcp any any eq www access-list inside extended permit ip any any access-list inside extended permit icmp any any access-list dmz extended permit ip any any access-list dmz extended permit icmp any any access-list cap extended permit ip 10.1.4.0 255.255.252.0 172.16.16.0 255.255.25 5.0 access-list cap extended permit ip 172.16.16.0 255.255.255.0 10.1.4.0 255.255.25 2.0 no pager logging enable logging buffer-size 5000 logging monitor warnings logging trap warnings mtu outside 1500 mtu inside 1500 mtu dmz 1500 no failover asdm image disk0:/asdm-508.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (dmz,outside) tcp 41.223.156.106 www 172.16.16.80 www netmask 255.255.255 .255 static (dmz,outside) tcp 41.223.156.107 smtp 172.16.16.25 smtp netmask 255.255.2 55.255 static (inside,dmz) 10.1.0.0 10.1.16.0 netmask 255.255.252.0 access-group OUT-TO-DMZ in interface outside access-group inside in interface inside access-group dmz in interface dmz route outside 0.0.0.0 0.0.0.0 41.223.156.108 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 timeout mgcp-pat 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute http server enable http 10.1.4.0 255.255.252.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh timeout 5 console timeout 0 management-access inside ! ! match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect dns maximum-length 512 inspect ftp inspect h323 h225 inspect h323 ras inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp ! service-policy global_policy global Cryptochecksum: : end ASA-FW# Please Help. Big Denzel

    Read the article

  • Finding N contiguous zero bits in an integer to the left of the MSB position of another integer

    - by James Morris
    The problem is: given an integer val1 find the position of the highest bit set (Most Significant Bit) then, given a second integer val2 find a contiguous region of unset bits, with the minimum number of zero bits given by width to the left of the position (ie, in the higher bits). Here is the C code for my solution: typedef unsigned int t; unsigned const t_bits = sizeof(t) * CHAR_BIT; _Bool test_fit_within_left_of_msb( unsigned width, t val1, t val2, unsigned* offset_result) { unsigned offbit = 0; unsigned msb = 0; t mask; t b; while(val1 >>= 1) ++msb; while(offbit + width < t_bits - msb) { mask = (((t)1 << width) - 1) << (t_bits - width - offbit); b = val2 & mask; if (!b) { *offset_result = offbit; return true; } if (offbit++) /* this conditional bothers me! */ b <<= offbit - 1; while(b <<= 1) offbit++; } return false; } Aside from faster ways of finding the MSB of the first integer, the commented test for a zero offbit seems a bit extraneous, but necessary to skip the highest bit of type t if it is set. I have also implemented similar algorithms but working to the right of the MSB of the first number, so they don't require this seemingly extra condition. How can I get rid of this extra condition, or even, are there far more optimal solutions? Edit: Some background not strictly required. The offset result is a count of bits from the high bit, not from the low bit as maybe expected. This will be part of a wider algorithm which scans a 2D array for a 2D area of zero bits. Here, for testing, the algorithm has been simplified. val1 represents the first integer which does not have all bits set found in a row of the 2D array. From this the 2D version would scan down which is what val2 represents. Here's some output showing success and failure: t_bits:32 t_high: 10000000000000000000000000000000 ( 2147483648 ) --------- ----------------------------------- *** fit within left of msb test *** ----------------------------------- val1: 00000000000000000000000010000000 ( 128 ) val2: 01000001000100000000100100001001 ( 1091569929 ) msb: 7 offbit:0 + width: 8 = 8 mask: 11111111000000000000000000000000 ( 4278190080 ) b: 01000001000000000000000000000000 ( 1090519040 ) offbit:8 + width: 8 = 16 mask: 00000000111111110000000000000000 ( 16711680 ) b: 00000000000100000000000000000000 ( 1048576 ) offbit:12 + width: 8 = 20 mask: 00000000000011111111000000000000 ( 1044480 ) b: 00000000000000000000000000000000 ( 0 ) offbit:12 iters:10 ***** found room for width:8 at offset: 12 ***** ----------------------------------- *** fit within left of msb test *** ----------------------------------- val1: 00000000000000000000000001000000 ( 64 ) val2: 00010000000000001000010001000001 ( 268469313 ) msb: 6 offbit:0 + width: 13 = 13 mask: 11111111111110000000000000000000 ( 4294443008 ) b: 00010000000000000000000000000000 ( 268435456 ) offbit:4 + width: 13 = 17 mask: 00001111111111111000000000000000 ( 268402688 ) b: 00000000000000001000000000000000 ( 32768 ) ***** mask: 00001111111111111000000000000000 ( 268402688 ) offbit:17 iters:15 ***** no room found for width:13 ***** (iters is the count of iterations of the inner while loop)

    Read the article

  • EBS 11i and R12 certified with DB 11gR2 11.2.0.1 on Windows

    - by Steven Chan
    Oracle Database 11g Release 2 (11gR2) version 11.2.0.1 is now certified with Oracle E-Business Suite 11i and 12 on the following Microsoft Windows Server (32-bit) and Windows x64 (64-bit) operating systems:Windows Server 2003 (32-bit and 64-bit) Windows Server 2003 R2 (32-bit and 64-bit)Windows Server 2008 (32-bit and 64-bit)Windows Server 2008 R2 (64-bit only)Certified EBS ReleasesOracle E-Business Suite Release 11.5.10.2Oracle E-Business Suite Release 12.0.4 or higherOracle E-Business Suite Release  12.1.1 or higher

    Read the article

  • E: Sub-process /usr/bin/dpkg returned an error code (1) seems to be choking on kde-runtime-data version issue

    - by BMT
    12.04 LTS, on a dell mini 10. Install stable until about a week ago. Updated about 1x a week, sometimes more often. Several days ago, I booted up and the system was no longer working correctly. All these symptoms occurred simultaneously: Cannot run (exit on opening, every time): Update manager, software center, ubuntuOne, libreOffice. Vinagre autostarts on boot, no explanation, not set to startup with Ubuntu. Using apt-get to fix install results in the following: maura@pandora:~$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following package was automatically installed and is no longer required: libtelepathy-farstream2 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: gwibber gwibber-service kde-runtime-data software-center Suggested packages: gwibber-service-flickr gwibber-service-digg gwibber-service-statusnet gwibber-service-foursquare gwibber-service-friendfeed gwibber-service-pingfm gwibber-service-qaiku unity-lens-gwibber The following packages will be upgraded: gwibber gwibber-service kde-runtime-data software-center 4 upgraded, 0 newly installed, 0 to remove and 39 not upgraded. 20 not fully installed or removed. Need to get 0 B/5,682 kB of archives. After this operation, 177 kB of additional disk space will be used. Do you want to continue [Y/n]? debconf: Perl may be unconfigured (Can't locate Scalar/Util.pm in @INC (@INC contains: /etc/perl /usr/local/lib/perl/5.14.2 /usr/local/share/perl/5.14.2 /usr/lib/perl5 /usr/share/perl5 /usr/lib/perl/5.14 /usr/share/perl/5.14 /usr/local/lib/site_perl .) at /usr/lib/perl/5.14/Hash/Util.pm line 9. BEGIN failed--compilation aborted at /usr/lib/perl/5.14/Hash/Util.pm line 9. Compilation failed in require at /usr/share/perl/5.14/fields.pm line 122. Compilation failed in require at /usr/share/perl5/Debconf/Log.pm line 10. Compilation failed in require at (eval 1) line 4. BEGIN failed--compilation aborted at (eval 1) line 4. ) -- aborting (Reading database ... 242672 files and directories currently installed.) Preparing to replace gwibber 3.4.1-0ubuntu1 (using .../gwibber_3.4.2-0ubuntu1_i386.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/gwibber_3.4.2-0ubuntu1_i386.deb (--unpack): subprocess new pre-removal script returned error exit status 1 Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace gwibber-service 3.4.1-0ubuntu1 (using .../gwibber-service_3.4.2-0ubuntu1_all.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/gwibber-service_3.4.2-0ubuntu1_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace kde-runtime-data 4:4.8.3-0ubuntu0.1 (using .../kde-runtime-data_4%3a4.8.4-0ubuntu0.1_all.deb) ... Unpacking replacement kde-runtime-data ... dpkg: error processing /var/cache/apt/archives/kde-runtime-data_4%3a4.8.4-0ubuntu0.1_all.deb (--unpack): trying to overwrite '/usr/share/sounds', which is also in package sound-theme-freedesktop 0.7.pristine-2 dpkg-deb (subprocess): subprocess data was killed by signal (Broken pipe) dpkg-deb: error: subprocess <decompress> returned error exit status 2 Preparing to replace python-crypto 2.4.1-1 (using .../python-crypto_2.4.1-1_i386.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/python-crypto_2.4.1-1_i386.deb (--unpack): subprocess new pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace software-center 5.2.2.2 (using .../software-center_5.2.4_all.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/software-center_5.2.4_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Preparing to replace xdiagnose 2.5 (using .../archives/xdiagnose_2.5_all.deb) ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: warning: subprocess old pre-removal script returned error exit status 1 dpkg - trying script from the new package instead ... Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pyclean", line 25, in <module> import logging ImportError: No module named logging dpkg: error processing /var/cache/apt/archives/xdiagnose_2.5_all.deb (--unpack): subprocess new pre-removal script returned error exit status 1 No apport report written because MaxReports is reached already Could not find platform dependent libraries <exec_prefix> Consider setting $PYTHONHOME to <prefix>[:<exec_prefix>] Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging Error in sys.excepthook: Traceback (most recent call last): File "/usr/lib/python2.7/dist-packages/apport_python_hook.py", line 64, in apport_excepthook from apport.fileutils import likely_packaged, get_recent_crashes File "/usr/lib/python2.7/dist-packages/apport/__init__.py", line 1, in <module> from apport.report import Report File "/usr/lib/python2.7/dist-packages/apport/report.py", line 16, in <module> from xml.parsers.expat import ExpatError File "/usr/lib/python2.7/xml/parsers/expat.py", line 4, in <module> from pyexpat import * ImportError: No module named pyexpat Original exception was: Traceback (most recent call last): File "/usr/bin/pycompile", line 27, in <module> import logging ImportError: No module named logging dpkg: error while cleaning up: subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/gwibber_3.4.2-0ubuntu1_i386.deb /var/cache/apt/archives/gwibber-service_3.4.2-0ubuntu1_all.deb /var/cache/apt/archives/kde-runtime-data_4%3a4.8.4-0ubuntu0.1_all.deb /var/cache/apt/archives/python-crypto_2.4.1-1_i386.deb /var/cache/apt/archives/software-center_5.2.4_all.deb /var/cache/apt/archives/xdiagnose_2.5_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) maura@pandora:~$ ^C maura@pandora:~$

    Read the article

  • top tweets WebLogic Partner Community – March 2012

    - by JuergenKress
    Send us your tweets @wlscommunity #WebLogicCommunity and follow us on twitter http://twitter.com/wlscommunity PeterPaul ? RT @JDeveloper: EJB 3 Deployment guide for WebLogic Server Version: 10.3.4.0 dlvr.it/1J5VcV Andrejus Baranovskis ?Open ADF PopUp on Page Load fb.me/1Rx9LP3oW Sten Vesterli ? RT @OracleBlogs: Using the Oracle E-Business Suite SDK for Java on ADF Applications ow.ly/1hVKbB <- Neat! No more WS calls Java Buddy ?JavaFX 2.0: Example of MediaPlay java-buddy.blogspot.com/2012/03/javafx… Georges Saab Build improvements coming to #openJDK for #jdk8 mail.openjdk.java.net/pipermail/buil… NetBeans Team Share your #Java experience! JavaOne 2012 India call for papers: ow.ly/9xYg0 GlassFish ? GlassFish 3.1.2 Screencasts & Videos – bit.ly/zmQjn2 chriscmuir ?G+: New blog post: ADF Runtimes vs WLS versions as of JDeveloper 11.1.1.6.0 – bit.ly/y8tkgJ Michael Heinrichs New article: Creating a Sprite Animation with JavaFX blog.netopyr.com/2012/03/09/cre… Oracle WebLogic ? #WebLogic Devcast Webinar Series for March: Enterprise Java Scale Out, JPA, Distributed Grid Data Cache bit.ly/zeUXEV #Coherence Andrejus Baranovskis ?Extending Application Module for ADF BC Proxy User DB Connection fb.me/Bj1hLUqm OTNArchBeat ? Oracle Fusion Middleware on JDK 7 | Mark Nelson bit.ly/w7IroZ OTNArchBeat ? Java Champion Jonas Bonér Explains the Akka Platform bit.ly/x2GbXm Adam Bien ? (Java) FX Experience Tools–Feels Like Native Mac App: FX Experience Tools application comes with a native Mac O… bit.ly/waHF3H GlassFish ? GlassFish new recruit and Eclipse integration progress – bit.ly/y5eEkk JDeveloper & ADF Prototyping ADF Libraries dlvr.it/1Hhnw0 Eric Elzinga ?Oracle Fusion Middleware on JDK 7, bit.ly/xkphFQ ADF EMG ? Working with ADF in Arabic, Hebrew or other right-to-left-written language? Oracle UX asks for your help. groups.google.com/forum/?fromgro… Java ? A simple #JavaFX Login Form with a TRON like effect ow.ly/9n9AG JDeveloper & ADF ? Logging in Oracle ADF Applications dlvr.it/1HZhcX OTNArchBeat ? Oracle Cloud Conference: dates and locations worldwide bit.ly/ywXydR UK Oracle User Group ? Simon Haslam, ACE Director present on #WebLogic for DBAs at #oug_ire2012 j.mp/zG6vz3 @oraclewebcenter @oracleace #dublin Steven Davelaar ? Working with ADF and not a member of ADF EMG? You miss lots of valuable info, join now! sites.google.com/site/oracleemg… Simon Haslam @MaciejGruszka: Oracle plans to provide Forms & Reports plug-in for OVAB next year to help deployment. #ukoug MW SIG GlassFish ? Introducing JSR 357: Social Media API – bit.ly/yC8vez JAX London ? Are you coming to Java EE workshops by @AdamBien at JAX Days? Save £100 by registering today. #jaxdays #javaee jaxdays.com WebLogic Community ?Welcome to our Munich WebLogic 12c Bootcamp in Munich! If you also want to attend a training register for the Community oracle.com/partners/goto/… chriscmuir ? My first webcast for Oracle! (be kind) Basing ADF Business Component View Objects on More that one Entity Object bit.ly/ArKija OTNArchBeat ? Oracle Weblogic Server 12c is available on Oracle Solaris 11 (SPARC and x86) bit.ly/xE3TLg JDeveloper & ADF ? Basing ADF Business Component View Objects on More that one Entity Object – YouTube dlvr.it/1H93Qr OTNArchBeat ? Application-Driven Virtualization with Oracle Virtual Assembly Builder | Ronen Kofman bit.ly/wF1C1N Oracle WebLogic ? Steve Button’s blog: WebLogic Server Singleton Services ow.ly/1hOu4U Barbara Ann May ?@oracledevtools: New update: #NetBeans IDE 7.1.1, with support for #GlassFish 3.1.2 bit.ly/mOLcQd #java #developer OTNArchBeat ? Using Coherence with JDeveloper: bit.ly/AkoEQb WebLogic Community ? WebLogic Partner Community Newsletter February 2012 wp.me/p1LMIb-f3 GlassFish ? GlassFish 3.1.2 – new Podcast episode : bit.ly/wc6oBE Frank Nimphius ?Cool! Open JDeveloper 11.1.1.5, go help–>check for updates. First thing shown is that 11.1.1.6 is available. Never miss a new release Adam Bien ?5 Minutes (Video) With Java EE …Or With NetBeans + GlassFish: This screencast covers a 5-minute development of a… bit.ly/xkOJMf WebLogic Community ? Free Oracle WebLogic Certification Application Grid Implementation Specialist wp.me/p1LMIb-eT OTNArchBeat ?Oracle Coherence: First Steps Using Clusters and Basic API Usage | Ricardo Ferreira bit.ly/yYQ3Wz GlassFish ? JMS 2.0 Early Draft is here – bit.ly/ygT1VN OTNArchBeat ? Exalogic Networking Part 2 | The Old Toxophilist bit.ly/xuYMIi OTNArchBeat ?New Release: GlassFish Server 3.1.2. Read All About It! | Paul Davies bit.ly/AtlGxo Oracle WebLogic ?OTN Virtual Developer Day: #WebLogic 12c & #Coherence ost-conference on-demand page live with bonus #Virtualbox lab – bit.ly/xUy6BJ Oracle WebLogic ? Steve Button’s blog: WebLogic Server 11g (10.3.6) Documentation ow.ly/1hJgUB Lucas Jellema ? Just published an article on the AMIS blog: technology.amis.nl/2012/03/adf-11… ADF 11g – programmatically sorting rich table columns. Java Certification ? New Course! Learn how to create mobile applications using Java ME: bit.ly/xZj1Jh Simon Haslam ? @MaciejGruszka WebLogic 12c can run against 11g domain config without changes …and can rollback to 11. #ukoug MW SIG Justin Kestelyn ? Learn Advanced ADF, free and online bit.ly/wEKSRc WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: twitter,WebLogic,WebLogic Community,OPN,Oracle,Jürgen Kress,WebLogic 12c

    Read the article

  • OpenGL error LNK2019

    - by Ghilliedrone
    I'm trying to compile a basic OpenGL program. I linked opengl32.lib and glu32.lib but I'm getting errors. The errors I get are: error LNK1120: 7 unresolved externals error LNK2019: unresolved external symbol _main referenced in function ___tmainCRTStartup error LNK2019: unresolved external symbol "public: float __thiscall GLWindow::getElapsedSeconds(void)" (?getElapsedSeconds@GLWindow@@QAEMXZ) referenced in function _WinMain@16 error LNK2019: unresolved external symbol "public: bool __thiscall GLWindow::isRunning(void)" (?isRunning@GLWindow@@QAE_NXZ) referenced in function _WinMain@16 error LNK2019: unresolved external symbol "public: void __thiscall GLWindow::attachExample(class Example *)" (?attachExample@GLWindow@@QAEXPAVExample@@@Z) referenced in function _WinMain@16 error LNK2019: unresolved external symbol "public: void __thiscall GLWindow::destroy(void)" (?destroy@GLWindow@@QAEXXZ) referenced in function _WinMain@16 error LNK2019: unresolved external symbol "public: __thiscall GLWindow::GLWindow(struct HINSTANCE__ *)" (??0GLWindow@@QAE@PAUHINSTANCE__@@@Z) referenced in function _WinMain@16 error LNK2019: unresolved external symbol "private: void __thiscall GLWindow::setupPixelFormat(void)" (?setupPixelFormat@GLWindow@@AAEXXZ) referenced in function "public: long __stdcall GLWindow::WndProc(struct HWND__ *,unsigned int,unsigned int,long)" (?WndProc@GLWindow@@QAGJPAUHWND__@@IIJ@Z)

    Read the article

  • Animate button on MouseOver and MouseDown

    - by haagel
    I'm making my own ControlTemplate for a standard Button in WPF. I want to change the background of my button when the user hovers over the button with the mouse, but also when the user presses the button (to yet another color). This seems like a common behavior, but I can't get it to work. My template consists of a Border with an Image inside. It is the background color (a gradient really) of the Border that I want to animate. I have triggers in my template that activates animations (storyboards). The MouseOver/Out works just fine. My problem occurs when I press the button. The Press animation runs as it should, and so does the Release animation. But after this the MouseOut will never run. The button gets stuck in the MouseOver state. What am I doing wrong? <ControlTemplate TargetType="{x:Type Button}"> <ControlTemplate.Resources> <Storyboard x:Key="MouseOverAnimation"> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop1" Storyboard.TargetProperty="Color" To="#ffefefff" Duration="0:0:0.2" /> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop2" Storyboard.TargetProperty="Color" To="#ffc7c7ff" Duration="0:0:0.2" /> </Storyboard> <Storyboard x:Key="MouseOutAnimation"> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop1" Storyboard.TargetProperty="Color" To="#ffeeeeee" Duration="0:0:0.2" /> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop2" Storyboard.TargetProperty="Color" To="#ffcccccc" Duration="0:0:0.2" /> </Storyboard> <Storyboard x:Key="MouseDownAnimation"> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop1" Storyboard.TargetProperty="Color" To="#ffc7c7ff" Duration="0:0:0.1" /> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop2" Storyboard.TargetProperty="Color" To="#ff9a9aff" Duration="0:0:0.1" /> </Storyboard> <Storyboard x:Key="MouseUpAnimation"> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop1" Storyboard.TargetProperty="Color" To="#ffefefff" Duration="0:0:0.1" /> <ColorAnimation Storyboard.TargetName="ButtonBorderGradientStop2" Storyboard.TargetProperty="Color" To="#ffc7c7ff" Duration="0:0:0.1" /> </Storyboard> </ControlTemplate.Resources> <Border x:Name="ButtonBorder" CornerRadius="0" BorderBrush="#55aaaaaa" BorderThickness="1" Width="23" Height="22"> <Border.Background> <LinearGradientBrush StartPoint="0,0" EndPoint="0,1"> <GradientBrush.GradientStops> <GradientStop x:Name="ButtonBorderGradientStop1" Color="#ffeeeeee" Offset="0.0" /> <GradientStop x:Name="ButtonBorderGradientStop2" Color="#ffcccccc" Offset="1.0" /> </GradientBrush.GradientStops> </LinearGradientBrush> </Border.Background> <Image x:Name="ButtonIcon" Source="icons/searchicon_bw.png" Width="16" Height="16" /> </Border> <ControlTemplate.Triggers> <Trigger Property="IsMouseOver" Value="True"> <Trigger.EnterActions> <BeginStoryboard Storyboard="{StaticResource MouseOverAnimation}" /> </Trigger.EnterActions> <Trigger.ExitActions> <BeginStoryboard Storyboard="{StaticResource MouseOutAnimation}" /> </Trigger.ExitActions> </Trigger> <Trigger Property="IsPressed" Value="True"> <Trigger.EnterActions> <BeginStoryboard Storyboard="{StaticResource MouseDownAnimation}" /> </Trigger.EnterActions> <Trigger.ExitActions> <BeginStoryboard Storyboard="{StaticResource MouseUpAnimation}" /> </Trigger.ExitActions> </Trigger> </ControlTemplate.Triggers> </ControlTemplate>

    Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >