Search Results

Search found 4248 results on 170 pages for 'adsl router'.

Page 90/170 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• What are the essential considerations for setting up systems in a location with unreliable power?

  - by dunxd

  I deal with a lot of remote offices located in parts of the world where the local grid power supply is unreliable. Power can go off anytime with no warning, with outages ranging from minutes to days Power fluctuation is wild, with spikes and brown outs Currently the offices will have some or all of the following: A generator, with an inverter, or some sort of manual switch A big UPS or battery array connecting a number of devices Several smaller APC UPS with computers attached Low cost Voltage Regulators sometimes connected between mains and UPS or device. I know that each of these things needs to be appropriately rated for the equipment to which it is connected (although I am not sure how to calculate the correct rating). The offices will generally have the following equipment (in varying quantities): some sort of internet connection device (VSAT router, ADSL modem, WiMax router) Cisco ASA 5505 firewall a bunch of PCs printers one server I don't seek to replace the advice of an electrician, but in some of these locations they only answer the questions you ask them, so I need to make sure I have enough understanding of the essentials to protect equipment from damage, and possibly get through some power cuts.

  Read the article

• Establish direct cable connection between Windows 8 PCs in home network

  - by Marie. P.

  I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

  Read the article

• Jumbo Frames on DIR-655

  - by Spookyone

  I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Cross-platform automatic adhoc wifi?

  - by marienbad

  I'm not very knowledgeable about wifi, but I understand the notion of Adhoc networks (Wifi without a router), so... Is there a standard (or widely implemented) way of letting a device "momentarily" negotiate a wifi connection (Adhoc network or otherwise) directly to another device, transfer some data, and then quit, all without any user intervention on either device? For example, let's say I have a PC and an ereader in the same room and there's no nearby wifi router for either of these devices to connect to. I want to send a file from PC to ereader but I don't want to do the work of setting up network, selecting an SSID, or entering passwords. Is that possible?

  Read the article

• How can I make my Ubuntu server accessible to the internet ?

  - by wahid

  Hi, I already installed applications to make my server web server. when I type the DHCP released ip address in the web browser, i can access it but all it says is "it works....etc". I can copy files to /var/www successfuly using WINSCP but yet, i can not see any files when I connect to it using my windows machine in the browser. Secondly , I tried to forward port on my home SMC router, it only accepts local lan ip which my ubuntu server picks up internet ip from router...what should i do ? can you help please ???? Thanks,

  Read the article

• After a period of time, nslookup still works, but pinging, and an auto-refeshed website, fails.

  - by Mark Hurd

  Contrary to this SO question this is for a dotted name (gw.localnet.au), and it doesn't happen straight away. Only after some period of time (quite a long time, possibly days). In fact this is for my ADSL router and its internal IP address which I have named within the router itself and in my Windows Server 2003 Domain Controller DNS Service. Specifically, localnet.au is a Active-Directory-backed primary domain. In fact, an ipconfig /flushdns may fix the problem, but only after a while (about the time it took me to type in this question :-) ). That doesn't explain the root cause though... Manually transferred from stackoverflow.com

  Read the article

• Network based on Netgear FVS318 extremely slow

  - by Fentible

  A network I maintain uses an FVS318 as a router, with a separate switch. Communication within the network is slow. Out to the internet is even slower. As it stands there is one patch from the FVS to the switch and no other devices directly connected to the FVS because any that are run so slowly they might as well not be connected to the network. Swapping in a bog-standard home router dramatically increases network speed, but that's not a viable solution because some of the enterprise features of the FVS are required. There are quite a few complaints about this on the Netgear forum, but Netgear support have not been forthcoming with any help - so I turn to you all: any ideas?

  Read the article

• Cannot resolve a single A Record from client machine

  - by Alex

  I set up a simple Bind server on my VPS and it is working properly. The problem occurs with my local windows machines, which are connected to internet through the home router. I created an A-record named 'dev' and it is invisible from my local network for some reason, though people from other locations can resolve dev.mydomain.com. Ironically, dev.mydomain.com cannot be resolved for myself only. If I add another A-record, say, 'gamma' then it becomes visible from my local windows machines instantly. So this is just for that particular 'dev' name. The only difference is that I had dev.mydomain.com server on another IP but that was a month ago; all nameservers have been changed since then. I tried to reboot my router and flushed dns cache on windows machines: no result. Thank you in advance.

  Read the article

• NAT : understanding about interconnection

  - by PITCHY

  English version below J'ai 2 routeurs A et B relié en série avec les ip respectives ( 10.0.0.1/30 10.0.0.2/30) sur le routeur A j'ai activé la fonction NAT avec un pool (200.0.0.1 - 200.0.0.15/28). Lorsque je sors je prends donc un ip du pool par exemple 200.0.0.10. Comment ça fonctionne sachant que ma nouvelle ip (200.0.0.10) ne se trouve pas sur le meme réseau que mon interface de destination (10.0.0.2)? English: I have 2 routers A and B, interconnected with a serial connection, with the ip's 10.0.0.1/30 for A and 10.0.0.2/30 for B. On router A NAT was activated with the pool 200.0.0.1 - 200.0.0.15/28. When connection to this router, I get an ip from the pool, for example 200.0.0.10. Knowing my new ip is 200.0.0.10, which is not on the same network as my destination interface (10.0.0.2), how can this work?

  Read the article

• solving network connection problem on xp

  - by doug

  Hi there I feel so stupid, because I have to fix my dad computer(which was mine years ago). So it is an old computer on which I have installed windows xp and the drivers for main-board. The device manager says that I have no more problems with the hardware. That computer has to connect to a router from my room but it doesn't. On ping 192.168.2.1 I get "Request time out"., The other computers are connecting to that router. Only the old computer doesn't connect to the LAN and later to the internet. Also it doesn't get a good IP(from the same class). After running ipconfig command I know that i have an IP with 169.... What can I do? Do you have any tips for me?

  Read the article

• Network Role based routing

  - by Steve Butler

  Apologies my networking skills are a tad rusty. I'm looking for a way to setup a system that gives me the ability to setup Role-based access to specific network resources. For example, i have three private subnets for specific groups, users will need access to one one or more subnets. I'd like to have all client machines on the same subnet/vlan, and then use 802.1x to authorize into a router(NAC device/whatever), the router would then see what user had authenticated(huge plus if it could determine AD group), and then allow routing to one or more of the three private subnets based upon their group membership. I've looked at packetFence, and it appears to work by assigning a client to a VLAN, but i'd still need a way to route some users into different back-end networks.

  Read the article

• Does my dd-wrt installation support firewall logging?

  - by SpikeX

  I would like to log firewall events. I know this is possible with dd-wrt, but a lot of the documentation I've read states that this isn't possible with a micro installation of dd-wrt (based on BusyBox). I have a Netgear WNDR3700v2 router, and it does have BusyBox installed on it, but I don't know if the dd-wrt build is a micro build or not. How can I find this out, or how can I find out if my router supports firewall logging or not? Currently, if I enable all firewall logging (setting everything to "Enabled" and/or "High" gives me back blank firewall logs - but syslogd is working because I can view other system log messages).

  Read the article

• wireless dropping out

  - by Sam

  My wireless network connection is dropping out and its driving me nuts. It is weird because it happens at totally random intervals and other devices work while my computer has been dropped. Both my USB dongle and wifi card randomly disconnect from the router and I am unable to connect for a couple of minutes. It is especially irritating because two different adapters are failing at the same time, sounds like a software problem to me, but where? Both my laptop and iPod remain connected when the connection drops. What on earth is happening? I doubt its the router because the other devices would disconnect as well.

  Read the article

• Web Development - How to access custom host, defined in my hosts file, from another device in the same network

  - by Neara

  Ok, I hope i'll be able to explain the issue im experiencing. I'm working on a project, that has 2 parts: one takes all requests from usual localhost, the other handles requests from myhost.local. While trying to access both addresses from my computer, it works ok. But now i need to test myhost.local on mobile devices, connected to the same network. Usually i would just run server from my computer ip in the network: python manage.py runserver 10.0.0.8:8000 And then from any device, going to 10.0.0.8:8000 would show the project im working on. However, now accessing that ip address routes me straight to localhost. So, my question is how to access myhost.local from another device in same network? I don't want to change router settings, if that can be avoided, cos sometimes i work from places where i can't access router admin. Is there any network settings on my computer, that i can change to fix the routing to myhost.local w.o losing access to localhost as well?

  Read the article

• how to set up domain name, bad request invalid hostname

  - by user45645

  assume i have a domain name which will be forwarded to my public ip (web server) automatically. in IIS 6, ip is public ip port is 6666, advanced - host value is www.hello.com firewall is open for 6666(web server port) and 53(DNS port), DMZ of router is my physical address in DNS, i have already had a zone called oldhello.com. And i expect a new domain name. So i have addded a new zone called hello.com and checked SOA server (P) is one.hello.local. then added a new host called one, full name is one.hello.com, ip address 192.168.7.3(my address in router) and then add a alias(CNAME) www, full name is www.hello.com, FQDN i choose the host i added before (one.hello.com) i expected that when i type the public ip in browser, can it be changed to domain name automatically. if not set host value www.hello.com, use public ip i can see the web however, after set up host value www.hello.com, browser show bad request invalid hostname

  Read the article

• Asus RT-N66U forgets USB-Printer

  - by heysamhey

  about a week ago I bought the new Asus RT-N66U as the new Router in our little company. There are about 5 clients and 2 printers. There's a USB-only printer as well, therefor we bougth a router with USB-printer sharing. The setup and everything works smooth, but then after one day, and I still haven't found out why, suddenly the printer dosen't show up in the list of connected devices in the routers webinterface anymore. Of course I loose the possibility of printig, even though the printer shows up as "online" in the system settings. Can anybody guess the reason for this problem? Thank you very much

  Read the article

• Can't access internet even though everything is working

  - by entity64

  A friend recently upgraded to a new cable internet connection. The modem connects to the router and various PCs and smartphones from her roommates connect to the router. They don't have any problem accessing the internet. She has Windows 8 and can't access any website (via wifi and ethernet). DNS (UDP) is working, DHCP set up everything correctly, Wifi is working, Trace routes and Pings (ICMP) go through with no problem at all. But neither Dropbox nor Skype nor Spotify nor any browser (all TCP) can access any website. The thing is though, she can connect through the university wifi and via a neighbors wifi. It's just her home connection. No firewalls are running and the computer is clean - no malware. How could it be that only her home connection won't work and others do?

  Read the article

• Which ports for IPSEC/LT2P?

  - by Matt

  I have a firewall/router (not doing NAT). I've googled and seen conflicting answers. It seems UDP 500 is the common one. But the others are confusing. 1701, 4500. And some say I need to also allow gre 50, or 47, or 50 & 51. Ok, which ports are the correct ones for IPSec/L2TP to work in a routed environment without NAT? i.e. I want to use the built in windows client to connect to a VPN behind this router/firewall.

  Read the article

• Connecting desktop computer to the internet through laptop wifi

  - by Josh

  Due to some home network complications I have had to move my router to a seperate part of the house, therefore the wired network I had set up can no longer work. Before I find the time to go out and buy a Wifi adapter for my desktop PC, I have a laptop that uses a built in Wifi card to connect to my router and this can connect to the internet, and I was wondering if I could somehow access the internet on my desktop PC via my laptop. I'm hoping for a not-so-complex solution as this will only be set up for a few days, but it is quite vital that my desktop computer gets internet access. Does anyone have experience in this sort of thing and can help me out? Thanks.

  Read the article

• How Do I Enable CUPS Browsing Across A Network?

  - by David Mackintosh

  I have a CUPS server with two print queues defined. Once this was defined, all the CUPS clients on the same subnet could see the two print queues automatically, no problem. Now I have a collection of machines on a separate subnet, reachable from the first subnet by a router. How do I enable CUPS browsing on the second set of machines so that they can see the print queues defined on the first machine? Let's call the server A.B.C.7. The first subnet is A.B.C.0/24. The second subnet is A.B.D.0/24, and there is a router with arms on both networks.

  Read the article

• Extremely poor WiFi reception on new desktop

  - by guy

  I just received a new desktop with a built-in WiFi card (Windows 7 Home Premium x64). However, I am only able to receive any WiFi signal when the computer is within 1-2 meters of a router. Even then, the signal is very weak (Windows 7 says it is "poor"). I have tried this with 2 different routers and see similar results. I have somewhere around a dozen other devices that can connect to both routers with greater signal strength (usually full strength) from much, much further away. When I tried calling support I was instructed to reinstall my drivers and attempt to change the WiFi channel of the router. Neither worked. I was then told that the problem was with my routers and that the computer was functioning normally and that it was certainly not a hardware problem. What would be the cause of this and is there anything I can do to fix it?

  Read the article

• Reasons for Wi-Fi to be slower on Ubuntu compared to Windows?

  - by den-javamaniac

  I'm using 64-bit Ubuntu 12.04 and Windows 7 64 bit – dual boot on the same computer. Connecting to the same wireless network. And it turns out that on Windows I get a more stable and stronger signal than on Ubuntu. To my knowledge there's a router which serves as a gateway and then there's a cable connected to the router which goes further to ISP, so the results for both OS should be the same. I've tested the issue on both OSs at various times and it gave me the same result. The question is why? Why Ubuntu networking is worse than that of Windows?

  Read the article

• Squid3 not working. Access denied

  - by Nitish

  I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

  Read the article

• How to configure DNS BIND to work locally on one computer?

  - by user619656

  I want to do some changes to the BIND source code. In order to test those changes I want to be able to post queries to my local BIND server and for it to use only the local zone files. I know how to make the zone files and somewhat the named.conf file but what should i put in /etc/resolv.conf? In resolv.conf currently there is the line nameserver 192.168.0.1 witch i guess is my router IP address and the queries go through the router to my ISP. I want those queries to go to the local BIND server and to look for answers in the zone files i provided. Is there a way for this using resolf.conf file or should i do something else?

  Read the article

• What do user accounts do?

  - by Fasih Khatib

  Ok, this is my first time with windows server os. I started doing this out of curiosity. I have a desktop running windows server os 2003 which is connected to a wifi router. I have a laptop that connects to this router wirelessly and THIS REPRESENTS A REMOTE USER. I want to provide access to this user to a set of files ON THE SERVER. So i create an account for this user, as Start - programs - admin tools -user manager and then the steps to create an account. When i use this laptop, i log in as administrator as its the default account that came. Now when i want this laptop to be the user i just created on the server, HOW DO I DO THAT?

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >