Search Results

Search found 2372 results on 95 pages for 'flashing the bios'.

Page 90/95 | < Previous Page | 86 87 88 89 90 91 92 93 94 95  | Next Page >

• Linux can dual display but windows can't?

  - by Mr_CryptoPrime

  I have two monitors, one that is hdmi-to-dvi and the other vga-to-dvi. I have an AMD HD Radeon 6900 series graphics card installed. I got Ubuntu to display dual monitors, but then I restarted for an update and then Ubuntu wouldn't even boot in recovery mode, it just kept cycling forever...displaying something about "timeout: killing [filepath] [hexadecimal]. So I tried booting into windows (7-professional) and it crashed and displayed this after rebooting: IRQL_NOT_LESS_OR_EQUAL, PAGE_FAULT-IN-NONPAGED-AREA. I went into Bios and reverted to the system defaults and ran system restore and it booted ok, but the dvi-to-dvi monitor would not display. I made sure my drivers were updated and catalyst was updated. Also through research discovered only one is for vga and the other is digital only, so I put the vga-to-dvi in the vga slot and so on. Neither windows or catalyst will detect the dvi-to-dvi montior. Any suggestions? Thanks. EDIT: Found out that booting into Ubuntu with only one monitor (using either monitor with either cable) worked perfectly fine. I could then add another monitor and it displays ok. However, it will, out of the blue, suddenly distort the display. At first I thought the computer crashed, but it is something with the video output from the GPU to the monitor because I pushed the power button and it would refresh every 5secs or so and I could see the "Ubuntu will power down in X seconds", even though it was horribly distorted. Any ideas what's causing this?

  Read the article

• SATA disks boot order?

  - by kire

  I have a computer with 4 SATA disks connected, 2 to the motherboard and 2 to a PCI-card. I've moved all the disks from other computers so 2 of them already has windows installed, the other 2 has just had data on them. I know one of the windows installations works and i want to use this install. If i only have this disk connected the computer boots fine. The problem is that when i boot with all 4 disks connected i get an error message about not being able to boot. This message is in swedish(the wrong windows installation is swedish) so it has to come from that installation. Ok, that means it is trying to boot from wrong disk, i try to pull out that disk but then i get the same error in english. I pull out the fourth disk instead I get another error about NTLDR not being able to load. If i disconnect all drives except the one with the correct windows installation, windows boots fine and i can also connect the other drives while windows is running and browse around in them without any problems. I have no clue what to do. In my BIOS setup i can only select SATA as boot-option, not the order of the disks. I also tried to remove what's left of windows on the other disk by simply deleting everything in explorer(got hidden- and sytstem-files visible). Both windows installations are XP btw. Edit: I switched the cables around and now it magically works. :)

  Read the article

• SSD won't boot anymore

  - by LordrAider

  Yesterday I put the computer to sleep. Something went wrong because it didn't go fully to sleep. So I restarted the pc and now it won't boot windows 7 anymore. It said : "Please insert valid boot device". I ran Windows 7 restore disc and tried restoring, first it said, mbr fixed. No result but now it said : "Operating system could not be loaded" I ran Windows 7 restore disc again and then it said something about a corrupt partition and that he fixed it. But got the same msg at restart about operating system not found. I ran Windows 7 restore disc again and used diskpart and watched the volumes. My SSD shows up as RAW filesystem... not as NTFS. The size of the disk seems correct. In the bios it also shows up as Healthy disk. What could went wrong and could I recover data with testdisk? I assume something went wrong with the partition :(. It's a Plextor SSD 256M2P SSD, only 3 months old. Thx in advance

  Read the article

• Windows 8 Killed my SSDs

  - by SLaks

  I have a computer running 2 256GB Crucial M4's (CT256M4SSD2) in a RAID 0 (striped) array on an ASUS P9X79 Pro using Intel's (built-in) RAID system. I recently installed Windows 8 Pro as UEFI on this RAID array. (wiping a fully-function Windows 7 non-UEFI installation) Now, whenever the computer is left running for about an hour, the system no longer sees those drives. Since those drives contain Windows, this leads to various forms of BSODs. If I Intel RSTe (RAID manager) is running at the time, it will say that the disk backing that RAID array has been removed. Once this happens, if I reset the computer, it will no longer boot. Entering BIOS setup shows that the SATA 3 (6Gbps) ports that those disks are connected to are both empty. If I then power down the system completely, then turn it on again, the drives reappear, but the problem repeats after another hour or so. I have inconclusively determined that the problem occurs even if Windows is not running (booted into the installation environment from a UEFI flash drive) I don't think there has been any data corruption since this started happening, although I have had two strange issues with a GIT repo on that disk. sfc /ScanNow and Intel's disk check (in RSTe) both do not find anything. Does anyone know what might cause this?

  Read the article

• Ubuntu 9.10 won't reboot after replacing a failed drive

  - by user149041

  Hello Serverfault community. I hope someone can shed light on a peculiar problem I am having with an Ubuntu 9.10 server install. I am not a Linux expert but have the responsibility of fixing the box if something goes wrong. DOH! I have Ubuntu 9.10 server installed on on a desktop platform: Compaq Presario SR5027CL. There are two 1TB SATA drives configured in a RAID 1 array; I use the box as an email backup server for a small group of users. Last week one of the drives failed and was replaced with a new drive of the same type. The problem I have been having is getting the box to reboot after a restart or a shutdown halt. The OS and the RAID 1 array are on the same drives that make up the RAID 1 array. The replacement drive (sda) was added to the box and the partitions were created to match the existing good drive (sdb). The array is made up of sda1 and sdb1. I found an interesting point while checking the BIOS settings: there is a "HDD Boot Group Priority" section, and the new drive was selected as the "1. 3rd master"; the server wouldn't boot configured like that, but when I set the old drive to be "1. 4th master", the box will reboot. I'm checking some more things, but I would certainly appreciate any useful information. Thanks in advance.

  Read the article

• Use Autoruns to Manually Clean an Infected PC

  - by Mark Virtue

  There are many anti-malware programs out there that will clean your system of nasties, but what happens if you’re not able to use such a program?  Autoruns, from SysInternals (recently acquired by Microsoft), is indispensable when removing malware manually. There are a few reasons why you may need to remove viruses and spyware manually: Perhaps you can’t abide running resource-hungry and invasive anti-malware programs on your PC You might need to clean your mom’s computer (or someone else who doesn’t understand that a big flashing sign on a website that says “Your computer is infected with a virus – click HERE to remove it” is not a message that can necessarily be trusted) The malware is so aggressive that it resists all attempts to automatically remove it, or won’t even allow you to install anti-malware software Part of your geek credo is the belief that anti-spyware utilities are for wimps Autoruns is an invaluable addition to any geek’s software toolkit.  It allows you to track and control all programs (and program components) that start automatically with Windows (or with Internet Explorer).  Virtually all malware is designed to start automatically, so there’s a very strong chance that it can be detected and removed with the help of Autoruns. We have covered how to use Autoruns in an earlier article, which you should read if you need to first familiarize yourself with the program. Autoruns is a standalone utility that does not need to be installed on your computer.  It can be simply downloaded, unzipped and run (link below).  This makes is ideally suited for adding to your portable utility collection on your flash drive. When you start Autoruns for the first time on a computer, you are presented with the license agreement: After agreeing to the terms, the main Autoruns window opens, showing you the complete list of all software that will run when your computer starts, when you log in, or when you open Internet Explorer: To temporarily disable a program from launching, uncheck the box next to it’s entry.  Note:  This does not terminate the program if it is running at the time – it merely prevents it from starting next time.  To permanently prevent a program from launching, delete the entry altogether (use the Delete key, or right-click and choose Delete from the context-menu)).  Note:  This does not remove the program from your computer – to remove it completely you need to uninstall the program (or otherwise delete it from your hard disk). Suspicious Software It can take a fair bit of experience (read “trial and error”) to become adept at identifying what is malware and what is not.  Most of the entries presented in Autoruns are legitimate programs, even if their names are unfamiliar to you.  Here are some tips to help you differentiate the malware from the legitimate software: If an entry is digitally signed by a software publisher (i.e. there’s an entry in the Publisher column) or has a “Description”, then there’s a good chance that it’s legitimate If you recognize the software’s name, then it’s usually okay.  Note that occasionally malware will “impersonate” legitimate software, but adopting a name that’s identical or similar to software you’re familiar with (e.g. “AcrobatLauncher” or “PhotoshopBrowser”).  Also, be aware that many malware programs adopt generic or innocuous-sounding names, such as “Diskfix” or “SearchHelper” (both mentioned below). Malware entries usually appear on the Logon tab of Autoruns (but not always!) If you open up the folder that contains the EXE or DLL file (more on this below), an examine the “last modified” date, the dates are often from the last few days (assuming that your infection is fairly recent) Malware is often located in the C:\Windows folder or the C:\Windows\System32 folder Malware often only has a generic icon (to the left of the name of the entry) If in doubt, right-click the entry and select Search Online… The list below shows two suspicious looking entries:  Diskfix and SearchHelper These entries, highlighted above, are fairly typical of malware infections: They have neither descriptions nor publishers They have generic names The files are located in C:\Windows\System32 They have generic icons The filenames are random strings of characters If you look in the C:\Windows\System32 folder and locate the files, you’ll see that they are some of the most recently modified files in the folder (see below) Double-clicking on the items will take you to their corresponding registry keys: Removing the Malware Once you’ve identified the entries you believe to be suspicious, you now need to decide what you want to do with them.  Your choices include: Temporarily disable the Autorun entry Permanently delete the Autorun entry Locate the running process (using Task Manager or similar) and terminating it Delete the EXE or DLL file from your disk (or at least move it to a folder where it won’t be automatically started) or all of the above, depending upon how certain you are that the program is malware. To see if your changes succeeded, you will need to reboot your machine, and check any or all of the following: Autoruns – to see if the entry has returned Task Manager (or similar) – to see if the program was started again after the reboot Check the behavior that led you to believe that your PC was infected in the first place.  If it’s no longer happening, chances are that your PC is now clean Conclusion This solution isn’t for everyone and is most likely geared to advanced users. Usually using a quality Antivirus application does the trick, but if not Autoruns is a valuable tool in your Anti-Malware kit. Keep in mind that some malware is harder to remove than others.  Sometimes you need several iterations of the steps above, with each iteration requiring you to look more carefully at each Autorun entry.  Sometimes the instant that you remove the Autorun entry, the malware that is running replaces the entry.  When this happens, we need to become more aggressive in our assassination of the malware, including terminating programs (even legitimate programs like Explorer.exe) that are infected with malware DLLs. Shortly we will be publishing an article on how to identify, locate and terminate processes that represent legitimate programs but are running infected DLLs, in order that those DLLs can be deleted from the system. Download Autoruns from SysInternals Similar Articles Productive Geek Tips Using Autoruns Tool to Track Startup Applications and Add-onsHow To Get Detailed Information About Your PCSUPERAntiSpyware Portable is the Must-Have Spyware Removal Tool You NeedQuick Tip: Windows Vista Temp Files DirectoryClear Recent Commands From the Run Dialog in Windows XP TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional 15 Great Illustrations by Chow Hon Lam Easily Sync Files & Folders with Friends & Family Amazon Free Kindle for PC Download Stretch popurls.com with a Stylish Script (Firefox) OldTvShows.org – Find episodes of Hitchcock, Soaps, Game Shows and more Download Microsoft Office Help tab

  Read the article

• DirectX works for 64-bit but not 32-bit

  - by dtbarne

  I'm trying to play a game (Civilization 5) which was previously working but no longer. I believe I've narrowed it down to a DirectX issue because I get an error running dxdiag.exe in 32 bit mode. My goal (at least I believe) is to get Direct3D Acceleration "Enabled" in dxdiag (as it is in 64 bit dxdiag). A very similar issue is here: http://answers.microsoft.com/en-us/windows/forum/windows_7-gaming/direct3d-acceleration-is-not-available-in-windows/4c345e6e-dc68-e011-8dfc-68b599b31bf5?page=1 The proposed answer, which looks very promising, doesn't seem to work for me. Like other users in that thread, HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Microsoft\Direct3D\Drivers does not have a SoftwareOnly key to change. I even tried manually adding it as a string and dword, to no avail. I have a NVIDIA GeForce GT 525M, and before you ask, yes I've tried updating (also uninstalling, reinstalling) my drivers. I've also tried doing the same with DirectX (and Civilization 5 for that matter). Been debugging for some 4+ hours now after a full day of work and I've run out of ideas. I'm hoping somebody knows the solution here! :) Here's what I see when I open dxdiag: DxDiag has detected that there mgiht have been a problem accessing Direct3D the last time this program was used. Would you like to bypass Direct3D this time? No - Crash Yes - Works, but in Display tab: DirectDraw Acceleration: Disabled Direct3D Acceleration: Not Available AGP Texture Acceleration: Not Available If I click "Run 64-bit DxDiag", all three are "Enabled". I should also note that I've tried the following steps as Microsoft suggests, but I'm not able to do so as the "Change Settings" button is disabled. Some programs run very slowly—or not at all—unless Microsoft DirectDraw or Direct3D hardware acceleration is turned on. To determine this, click the Display tab, and then under DirectX Features, check to see whether DirectDraw, Direct3D, and AGP Texture Acceleration appear as Enabled. If not, try turning on hardware acceleration. Click to open Screen Resolution. Click Advanced settings. Click the Troubleshoot tab, and then click Change settings. If you're prompted for an administrator password or confirmation, type the password or provide confirmation. Move the Hardware Acceleration slider to Full. Full dxdiag dump: ------------------ System Information ------------------ Time of this report: 11/8/2012, 23:13:24 Machine name: DTBARNE Operating System: Windows 7 Professional 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120830-0333) Language: English (Regional Setting: English) System Manufacturer: Dell Inc. System Model: Dell System XPS L502X BIOS: Default System BIOS Processor: Intel(R) Core(TM) i5-2450M CPU @ 2.50GHz (4 CPUs), ~2.5GHz Memory: 8192MB RAM Available OS Memory: 8086MB RAM Page File: 2466MB used, 13704MB available Windows Dir: C:\Windows DirectX Version: DirectX 11 DX Setup Parameters: Not found User DPI Setting: Using System DPI System DPI Setting: 96 DPI (100 percent) DWM DPI Scaling: Disabled DxDiag Version: 6.01.7601.17514 32bit Unicode DxDiag Previously: Crashed in Direct3D (stage 2). Re-running DxDiag with "dontskip" command line parameter or choosing not to bypass information gathering when prompted might result in DxDiag successfully obtaining this information ------------ DxDiag Notes ------------ Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Input Tab: No problems found. -------------------- DirectX Debug Levels -------------------- Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) --------------- Display Devices --------------- Card name: Intel(R) HD Graphics 3000 Manufacturer: Chip type: DAC type: Device Key: Enum\PCI\VEN_8086&DEV_0126&SUBSYS_04B61028&REV_09 Display Memory: Dedicated Memory: n/a Shared Memory: n/a Current Mode: 1920 x 1080 (32 bit) (60Hz) Monitor Name: Generic PnP Monitor Monitor Model: Monitor Id: Native Mode: Output Type: Driver Name: Driver File Version: () Driver Version: DDI Version: Driver Model: WDDM 1.1 Driver Attributes: Final Retail Driver Date/Size: , 0 bytes WHQL Logo'd: n/a WHQL Date Stamp: n/a Device Identifier: Vendor ID: Device ID: SubSys ID: Revision ID: Driver Strong Name: oem11.inf:IntelGfx.NTamd64.6.0:iSNBM0:8.15.10.2696:pci\ven_8086&dev_0126&subsys_04b61028 Rank Of Driver: 00E60001 Video Accel: Deinterlace Caps: n/a D3D9 Overlay: DXVA-HD: DDraw Status: Disabled D3D Status: Not Available AGP Status: Not Available ------------- Sound Devices ------------- Description: Speakers (High Definition Audio Device) Default Sound Playback: Yes Default Voice Playback: Yes Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0665&SUBSYS_102804B6&REV_1000 Manufacturer ID: 1 Product ID: 65535 Type: WDM Driver Name: HdAudio.sys Driver Version: 6.01.7601.17514 (English) Driver Attributes: Final Retail WHQL Logo'd: Yes Date and Size: 11/20/2010 22:23:47, 350208 bytes Other Files: Driver Provider: Microsoft HW Accel Level: Basic Cap Flags: 0xF1F Min/Max Sample Rate: 100, 200000 Static/Strm HW Mix Bufs: 1, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Digital Audio (S/PDIF) (High Definition Audio Device) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0665&SUBSYS_102804B6&REV_1000 Manufacturer ID: 1 Product ID: 65535 Type: WDM Driver Name: HdAudio.sys Driver Version: 6.01.7601.17514 (English) Driver Attributes: Final Retail WHQL Logo'd: Yes Date and Size: 11/20/2010 22:23:47, 350208 bytes Other Files: Driver Provider: Microsoft HW Accel Level: Basic Cap Flags: 0xF1F Min/Max Sample Rate: 100, 200000 Static/Strm HW Mix Bufs: 1, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No --------------------- Sound Capture Devices --------------------- Description: Microphone (High Definition Audio Device) Default Sound Capture: Yes Default Voice Capture: Yes Driver Name: HdAudio.sys Driver Version: 6.01.7601.17514 (English) Driver Attributes: Final Retail Date and Size: 11/20/2010 22:23:47, 350208 bytes Cap Flags: 0x1 Format Flags: 0xFFFFF ------------------- DirectInput Devices ------------------- Device Name: Mouse Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: Keyboard Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Poll w/ Interrupt: No ----------- USB Devices ----------- + USB Root Hub | Vendor/Product ID: 0x8086, 0x1C26 | Matching Device ID: usb\root_hub20 | Service: usbhub | +-+ Generic USB Hub | | Vendor/Product ID: 0x8087, 0x0024 | | Location: Port_#0001.Hub_#0002 | | Matching Device ID: usb\class_09 | | Service: usbhub ---------------- Gameport Devices ---------------- ------------ PS/2 Devices ------------ + Standard PS/2 Keyboard | Matching Device ID: *pnp0303 | Service: i8042prt | + Terminal Server Keyboard Driver | Matching Device ID: root\rdp_kbd | Upper Filters: kbdclass | Service: TermDD | + Synaptics PS/2 Port TouchPad | Matching Device ID: *dll04b6 | Upper Filters: SynTP | Service: i8042prt | + Terminal Server Mouse Driver | Matching Device ID: root\rdp_mou | Upper Filters: mouclass | Service: TermDD ------------------------ Disk & DVD/CD-ROM Drives ------------------------ Drive: C: Free Space: 26.2 GB Total Space: 122.0 GB File System: NTFS Model: M4-CT128M4SSD2 ATA Device Drive: D: Model: Optiarc DVDRWBD BC-5540H ATA Device Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7601.17514 (English), , 0 bytes -------------- System Devices -------------- Name: High Definition Audio Controller Device ID: PCI\VEN_8086&DEV_1C20&SUBSYS_04B61028&REV_05\3&11583659&0&D8 Driver: n/a Name: PCI standard host CPU bridge Device ID: PCI\VEN_8086&DEV_0104&SUBSYS_04B61028&REV_09\3&11583659&0&00 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C1A&SUBSYS_04B61028&REV_B5\3&11583659&0&E5 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_0101&SUBSYS_20108086&REV_09\3&11583659&0&08 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C18&SUBSYS_04B61028&REV_B5\3&11583659&0&E4 Driver: n/a Name: Intel(R) Centrino(R) Advanced-N 6230 Device ID: PCI\VEN_8086&DEV_0091&SUBSYS_52218086&REV_34\4&2634DE8D&0&00E1 Driver: n/a Name: PCI standard ISA bridge Device ID: PCI\VEN_8086&DEV_1C4B&SUBSYS_04B61028&REV_05\3&11583659&0&F8 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C16&SUBSYS_04B61028&REV_B5\3&11583659&0&E3 Driver: n/a Name: Realtek PCIe GBE Family Controller Device ID: PCI\VEN_10EC&DEV_8168&SUBSYS_04B61028&REV_06\4&109EAB2F&0&00E5 Driver: n/a Name: Intel(R) Management Engine Interface Device ID: PCI\VEN_8086&DEV_1C3A&SUBSYS_04B61028&REV_04\3&11583659&0&B0 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C12&SUBSYS_04B61028&REV_B5\3&11583659&0&E1 Driver: n/a Name: NVIDIA GeForce GT 525M Device ID: PCI\VEN_10DE&DEV_0DF5&SUBSYS_04B61028&REV_A1\4&4DCA75F&0&0008 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_8086&DEV_1C2D&SUBSYS_04B61028&REV_05\3&11583659&0&D0 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C10&SUBSYS_04B61028&REV_B5\3&11583659&0&E0 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_8086&DEV_1C26&SUBSYS_04B61028&REV_05\3&11583659&0&E8 Driver: n/a Name: Standard AHCI 1.0 Serial ATA Controller Device ID: PCI\VEN_8086&DEV_1C03&SUBSYS_04B61028&REV_05\3&11583659&0&FA Driver: n/a Name: SM Bus Controller Device ID: PCI\VEN_8086&DEV_1C22&SUBSYS_04B61028&REV_05\3&11583659&0&FB Driver: n/a Name: Intel(R) HD Graphics 3000 Device ID: PCI\VEN_8086&DEV_0126&SUBSYS_04B61028&REV_09\3&11583659&0&10 Driver: n/a Name: Renesas Electronics USB 3.0 Host Controller Device ID: PCI\VEN_1033&DEV_0194&SUBSYS_04B61028&REV_04\4&3494AC3A&0&00E3 Driver: n/a ------------------ DirectShow Filters ------------------ DirectShow Filters: WMAudio Decoder DMO,0x00800800,1,1,WMADMOD.DLL,6.01.7601.17514 WMAPro over S/PDIF DMO,0x00600800,1,1,WMADMOD.DLL,6.01.7601.17514 WMSpeech Decoder DMO,0x00600800,1,1,WMSPDMOD.DLL,6.01.7601.17514 MP3 Decoder DMO,0x00600800,1,1,mp3dmod.dll,6.01.7600.16385 Mpeg4s Decoder DMO,0x00800001,1,1,mp4sdecd.dll,6.01.7600.16385 WMV Screen decoder DMO,0x00600800,1,1,wmvsdecd.dll,6.01.7601.17514 WMVideo Decoder DMO,0x00800001,1,1,wmvdecod.dll,6.01.7601.17514 Mpeg43 Decoder DMO,0x00800001,1,1,mp43decd.dll,6.01.7600.16385 Mpeg4 Decoder DMO,0x00800001,1,1,mpg4decd.dll,6.01.7600.16385 DV Muxer,0x00400000,0,0,qdv.dll,6.06.7601.17514 Color Space Converter,0x00400001,1,1,quartz.dll,6.06.7601.17713 WM ASF Reader,0x00400000,0,0,qasf.dll,12.00.7601.17514 Screen Capture filter,0x00200000,0,1,wmpsrcwp.dll,12.00.7601.17514 AVI Splitter,0x00600000,1,1,quartz.dll,6.06.7601.17713 VGA 16 Color Ditherer,0x00400000,1,1,quartz.dll,6.06.7601.17713 SBE2MediaTypeProfile,0x00200000,0,0,sbe.dll,6.06.7601.17528 Microsoft DTV-DVD Video Decoder,0x005fffff,2,4,msmpeg2vdec.dll,6.01.7140.0000 AC3 Parser Filter,0x00600000,1,1,mpg2splt.ax,6.06.7601.17528 StreamBufferSink,0x00200000,0,0,sbe.dll,6.06.7601.17528 MJPEG Decompressor,0x00600000,1,1,quartz.dll,6.06.7601.17713 MPEG-I Stream Splitter,0x00600000,1,2,quartz.dll,6.06.7601.17713 SAMI (CC) Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7601.17514 MPEG-2 Splitter,0x005fffff,1,0,mpg2splt.ax,6.06.7601.17528 Closed Captions Analysis Filter,0x00200000,2,5,cca.dll,6.06.7601.17514 SBE2FileScan,0x00200000,0,0,sbe.dll,6.06.7601.17528 Microsoft MPEG-2 Video Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7601.17514 Internal Script Command Renderer,0x00800001,1,0,quartz.dll,6.06.7601.17713 MPEG Audio Decoder,0x03680001,1,1,quartz.dll,6.06.7601.17713 DV Splitter,0x00600000,1,2,qdv.dll,6.06.7601.17514 Video Mixing Renderer 9,0x00200000,1,0,quartz.dll,6.06.7601.17713 Microsoft MPEG-2 Encoder,0x00200000,2,1,msmpeg2enc.dll,6.01.7601.17514 ACM Wrapper,0x00600000,1,1,quartz.dll,6.06.7601.17713 Video Renderer,0x00800001,1,0,quartz.dll,6.06.7601.17713 MPEG-2 Video Stream Analyzer,0x00200000,0,0,sbe.dll,6.06.7601.17528 Line 21 Decoder,0x00600000,1,1,qdvd.dll,6.06.7601.17835 Video Port Manager,0x00600000,2,1,quartz.dll,6.06.7601.17713 Video Renderer,0x00400000,1,0,quartz.dll,6.06.7601.17713 VPS Decoder,0x00200000,0,0,WSTPager.ax,6.06.7601.17514 WM ASF Writer,0x00400000,0,0,qasf.dll,12.00.7601.17514 VBI Surface Allocator,0x00600000,1,1,vbisurf.ax,6.01.7601.17514 File writer,0x00200000,1,0,qcap.dll,6.06.7601.17514 iTV Data Sink,0x00600000,1,0,itvdata.dll,6.06.7601.17514 iTV Data Capture filter,0x00600000,1,1,itvdata.dll,6.06.7601.17514 DVD Navigator,0x00200000,0,3,qdvd.dll,6.06.7601.17835 Overlay Mixer2,0x00200000,1,1,qdvd.dll,6.06.7601.17835 AVI Draw,0x00600064,9,1,quartz.dll,6.06.7601.17713 RDP DShow Redirection Filter,0xffffffff,1,0,DShowRdpFilter.dll, Microsoft MPEG-2 Audio Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7601.17514 WST Pager,0x00200000,1,1,WSTPager.ax,6.06.7601.17514 MPEG-2 Demultiplexer,0x00600000,1,1,mpg2splt.ax,6.06.7601.17528 DV Video Decoder,0x00800000,1,1,qdv.dll,6.06.7601.17514 SampleGrabber,0x00200000,1,1,qedit.dll,6.06.7601.17514 Null Renderer,0x00200000,1,0,qedit.dll,6.06.7601.17514 MPEG-2 Sections and Tables,0x005fffff,1,0,Mpeg2Data.ax,6.06.7601.17514 Microsoft AC3 Encoder,0x00200000,1,1,msac3enc.dll,6.01.7601.17514 StreamBufferSource,0x00200000,0,0,sbe.dll,6.06.7601.17528 Smart Tee,0x00200000,1,2,qcap.dll,6.06.7601.17514 Overlay Mixer,0x00200000,0,0,qdvd.dll,6.06.7601.17835 AVI Decompressor,0x00600000,1,1,quartz.dll,6.06.7601.17713 AVI/WAV File Source,0x00400000,0,2,quartz.dll,6.06.7601.17713 Wave Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 MIDI Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 Multi-file Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 File stream renderer,0x00400000,1,1,quartz.dll,6.06.7601.17713 Microsoft DTV-DVD Audio Decoder,0x005fffff,1,1,msmpeg2adec.dll,6.01.7140.0000 StreamBufferSink2,0x00200000,0,0,sbe.dll,6.06.7601.17528 AVI Mux,0x00200000,1,0,qcap.dll,6.06.7601.17514 Line 21 Decoder 2,0x00600002,1,1,quartz.dll,6.06.7601.17713 File Source (Async.),0x00400000,0,1,quartz.dll,6.06.7601.17713 File Source (URL),0x00400000,0,1,quartz.dll,6.06.7601.17713 Infinite Pin Tee Filter,0x00200000,1,1,qcap.dll,6.06.7601.17514 Enhanced Video Renderer,0x00200000,1,0,evr.dll,6.01.7601.17514 BDA MPEG2 Transport Information Filter,0x00200000,2,0,psisrndr.ax,6.06.7601.17669 MPEG Video Decoder,0x40000001,1,1,quartz.dll,6.06.7601.17713 WDM Streaming Tee/Splitter Devices: Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 Video Compressors: WMVideo8 Encoder DMO,0x00600800,1,1,wmvxencd.dll,6.01.7600.16385 WMVideo9 Encoder DMO,0x00600800,1,1,wmvencod.dll,6.01.7600.16385 MSScreen 9 encoder DMO,0x00600800,1,1,wmvsencd.dll,6.01.7600.16385 DV Video Encoder,0x00200000,0,0,qdv.dll,6.06.7601.17514 MJPEG Compressor,0x00200000,0,0,quartz.dll,6.06.7601.17713 Cinepak Codec by Radius,0x00200000,1,1,qcap.dll,6.06.7601.17514 Intel IYUV codec,0x00200000,1,1,qcap.dll,6.06.7601.17514 Intel IYUV codec,0x00200000,1,1,qcap.dll,6.06.7601.17514 Microsoft RLE,0x00200000,1,1,qcap.dll,6.06.7601.17514 Microsoft Video 1,0x00200000,1,1,qcap.dll,6.06.7601.17514 Audio Compressors: WM Speech Encoder DMO,0x00600800,1,1,WMSPDMOE.DLL,6.01.7600.16385 WMAudio Encoder DMO,0x00600800,1,1,WMADMOE.DLL,6.01.7600.16385 IMA ADPCM,0x00200000,1,1,quartz.dll,6.06.7601.17713 PCM,0x00200000,1,1,quartz.dll,6.06.7601.17713 Microsoft ADPCM,0x00200000,1,1,quartz.dll,6.06.7601.17713 GSM 6.10,0x00200000,1,1,quartz.dll,6.06.7601.17713 CCITT A-Law,0x00200000,1,1,quartz.dll,6.06.7601.17713 CCITT u-Law,0x00200000,1,1,quartz.dll,6.06.7601.17713 MPEG Layer-3,0x00200000,1,1,quartz.dll,6.06.7601.17713 Audio Capture Sources: Microphone (High Definition Aud,0x00200000,0,0,qcap.dll,6.06.7601.17514 PBDA CP Filters: PBDA DTFilter,0x00600000,1,1,CPFilters.dll,6.06.7601.17528 PBDA ETFilter,0x00200000,0,0,CPFilters.dll,6.06.7601.17528 PBDA PTFilter,0x00200000,0,0,CPFilters.dll,6.06.7601.17528 Midi Renderers: Default MidiOut Device,0x00800000,1,0,quartz.dll,6.06.7601.17713 Microsoft GS Wavetable Synth,0x00200000,1,0,quartz.dll,6.06.7601.17713 WDM Streaming Capture Devices: HD Audio Microphone 2,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 Integrated Webcam,0x00200000,1,2,ksproxy.ax,6.01.7601.17514 WDM Streaming Rendering Devices: HD Audio Headphone/Speakers,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 HD Audio SPDIF out,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 BDA Network Providers: Microsoft ATSC Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft DVBC Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft DVBS Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft DVBT Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft Network Provider,0x00200000,0,1,MSNP.ax,6.06.7601.17514 Video Capture Sources: Integrated Webcam,0x00200000,1,2,ksproxy.ax,6.01.7601.17514 Multi-Instance Capable VBI Codecs: VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7601.17514 BDA Transport Information Renderers: BDA MPEG2 Transport Information Filter,0x00600000,2,0,psisrndr.ax,6.06.7601.17669 MPEG-2 Sections and Tables,0x00600000,1,0,Mpeg2Data.ax,6.06.7601.17514 BDA CP/CA Filters: Decrypt/Tag,0x00600000,1,1,EncDec.dll,6.06.7601.17708 Encrypt/Tag,0x00200000,0,0,EncDec.dll,6.06.7601.17708 PTFilter,0x00200000,0,0,EncDec.dll,6.06.7601.17708 XDS Codec,0x00200000,0,0,EncDec.dll,6.06.7601.17708 WDM Streaming Communication Transforms: Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 Audio Renderers: Speakers (High Definition Audio,0x00200000,1,0,quartz.dll,6.06.7601.17713 Default DirectSound Device,0x00800000,1,0,quartz.dll,6.06.7601.17713 Default WaveOut Device,0x00200000,1,0,quartz.dll,6.06.7601.17713 Digital Audio (S/PDIF) (High De,0x00200000,1,0,quartz.dll,6.06.7601.17713 DirectSound: Digital Audio (S/PDIF) (High Definition Audio Device),0x00200000,1,0,quartz.dll,6.06.7601.17713 DirectSound: Speakers (High Definition Audio Device),0x00200000,1,0,quartz.dll,6.06.7601.17713 --------------- EVR Power Information --------------- Current Setting: {651288E5-A7ED-4076-A96B-6CC62D848FE1} (Balanced) Quality Flags: 2576 Enabled: Force throttling Allow half deinterlace Allow scaling Decode Power Usage: 100 Balanced Flags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 50 PowerFlags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 0

  Read the article

• Installing the Updated XP Mode which Requires no Hardware Virtualization

  - by Mysticgeek

  Good news for those of you who have a computer without Hardware Virtualization, Microsoft had dropped the requirement so you can now run XP Mode on your machine. Here we take a look at how to install it and getting working on your PC. Microsoft has dropped the requirement that your CPU supports Hardware Virtualization for XP Mode in Windows 7. Before this requirement was dropped, we showed you how to use SecureAble to find out if your machine would run XP Mode. If it couldn’t, you might have gotten lucky with turning Hardware Virtualization on in your BIOS, or getting an update that would enable it. If not, you were out of luck or would need a different machine. Note: Although you no longer need Hardware Virtualization, you still need Professional, Enterprise, or Ultimate version of Windows 7. Download Correct Version of XP Mode For this article we’re installing it on a Dell machine that doesn’t support Hardware Virtualization on Windows 7 Ultimate 64-bit version. The first thing you’ll want to do is go to the XP Mode website and select your edition of Windows 7 and language. Then there are three downloads you’ll need to get from the page. Windows XP Mode, Windows Virtual PC, and the Windows XP Mode Update (All Links Below). Windows genuine validation is required before you can download the XP Mode files. To make the validation process easier you might want to use IE when downloading these files and validating your version of Windows. Installing XP Mode After validation is successful the first thing to download and install is XP Mode, which is easy following the wizard and accepting the defaults. The second step is to install KB958559 which is Windows Virtual PC.   After it’s installed, a reboot is required. After you’ve come back from the restart, you’ll need to install KB977206 which is the Windows XP Mode Update.   After that’s installed, yet another restart of your system is required. After the update is configured and you return from the second reboot, you’ll find XP Mode in the Start menu under the Windows Virtual PC folder. When it launches accept the license agreement and click Next. Enter in your log in credentials… Choose if you want Automatic Updates or not… Then you’re given a message saying setup will share the hardware on your computer, then click Start Setup. While setup completes, you’re shown a display of what XP Mode does and how to use it. XP Mode launches and you can now begin using it to run older applications that are not compatible with Windows 7. Conclusion This is a welcome news for many who want the ability to use XP Mode but didn’t have the proper hardware to do it. The bad news is users of Home versions of Windows still don’t get to enjoy the XP Mode feature officially. However, we have an article that shows a great workaround – Create an XP Mode for Windows 7 Home Versions & Vista. Download XP Mode, Windows Virtual PC, and Windows XP Mode Update Similar Articles Productive Geek Tips Our Look at XP Mode in Windows 7Run XP Mode on Windows 7 Machines Without Hardware VirtualizationInstall XP Mode with VirtualBox Using the VMLite PluginUnderstanding the New Hyper-V Feature in Windows Server 2008How To Run XP Mode in VirtualBox on Windows 7 (sort of) TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Ben & Jerry’s Free Cone Day, 3/23/10 New Stinger from McAfee Helps Remove ‘FakeAlert’ Threats Google Apps Marketplace: Tools & Services For Google Apps Users Get News Quick and Precise With Newser Scan for Viruses in Ubuntu using ClamAV Replace Your Windows Task Manager With System Explorer

  Read the article

• OBIEE 11.1.1 - Introduction to OBIEE 11g Full Sample App

  - by user809526

  Isn't it nice to discover OBIEE 11g around a nice "How To" catalog of features? to observe OBI and Essbase relationships at work? to discover TimesTen? The OBIEE 11g Full Sample App (FSA) is a comprehensive collection of examples designed to demonstrate the latest Oracle BIEE 11g capabilities and design best practices: Enhanced visualizations as Geo-spacial maps and interactive dashboards, Action Framework,  BI Publisher, Scorecard and Strategy Management, Mobile style sheets, Semantic layer modeling, Multi-source federation, Integration with products such as Essbase, Oracle OLAP, ODM, TimesTen, ODI and more The FSA is intended to be comprehensive, it is big (see CAVEAT below). The FSA is not an Oracle product, it is a good will free deployment of OBIEE/Essbase designed to exemplify OBIEE features, infrastructure and security around the Fusion Middleware components. Its contents and code are distributed free for demonstrative purposes only. It is neither maintained nor supported by Oracle as a licensed product. The OBIEE Full Sample App is independent of the default Sample App that comes with the OBIEE product. BENEFITS The FSA helps as a demonstrator of OBIEE 11g best practices, a tutorial, an environment "Test & Scrap", a SR bench (regression, conflicts), a tuning bench, a quick ready made POC seed for projects, a security options environment, ... The FSA - Is organized around a catalog of functional features - Has been deployed over 1000 times, it should be stable RELEASE The Full Sample App (V107) is bound to OBIEE 11.1.1.5 and Essbase 11.1.2.1 (November 2011). The FSA release dates are independent of the Product GA date (OBIEE). In early December 2011, a new functional Patch (V110) is released. It is easily applied (in less than 15 mins) on top of OBIEE SampleApp 11.1.1.5 (V107). The patch (V110) includes additional functional examples:        1. Web Catalog Statistics Application: Provides detailed insight into your web catalog content, dormant catalog objects, webcat impact analysis for metadata changes and more        2. Data inflation Scripts: A set of simple SQL procedures to quickly inflate SampleApp Fact and Dimension data to millions of records in a few minutes        3. Public Content Extensions Framework: A patching framework for public examples and contributions leveraging SampleApp        4. Additional report examples (including bridge report, external chart integrations) and bug fixes DISTRIBUTION as VBox image (November 2011) The ready made VBox image is designed to run on Virtual Box. It can be converted to VMware (see another BLOG). 1/ http://www.oracle.com/technetwork/middleware/bi-foundation/obiee-samples-167534.html VBox Image Deployment Guide Sampleapp_v107_GA.ovf - VBox image key file The above http URL provides the user:password for the ftp URLs below. 2/ ftp://user:[email protected]/static/SampleAppV107/ 12 "7-zip" files Sampleapp_v107_GA_7_20.7z.001 -> .012 We recommend 7-zip file manager for unzipping (http://www.7-zip.org/). Select Unzip here option, it will create the contents under a directory named "SampleApp_10722". On Windows, it is important to download and save zip file under the root directory (e.g. C:\ or D:\) because of possible long pathnames. 3/ ftp://user:[email protected]/static/SampleAppV107/Unzipped_Version/ 4 files Sampleapp_v107_GA-disk[1234].vmdk Important note: Check the provided checksums (md5sum). Please do it! DISTRIBUTION as Installation files for existing OBI 11.1.1.5 (November 2011) http://www.oracle.com/technetwork/middleware/bi-foundation/obiee-samples-167534.html Install files Deployment Guide SampleApp_10722_1.zip - 198 MB CAVEAT Many computers have RAM chips problems that keep often silent ... until you manipulate big files. It is strongly advised you run some memory check program eg MEMTEST in GRUB boot manager. Running md5sum repeatedly onto the very same big file must be consistent [same result], else a hardware memory problem is suspected. For Virtual Box, you should most likely enable VT-X (Vanderpool) hardware virtualization in BIOS. A free disk space of 80 GB is required to perform safely the VBox image installation. A Virtual Machine of minimum 6 to 7 GB memory fits the needs of combining OBIEE and Essbase execution.

  Read the article

• Installer Reboots at "Detecting hardware" (disks and other hardware) on all recent Server Installs

  - by Ryan Rosario

  I have a very frustrating problem with my PC. I cannot install any recent version of Ubuntu Server (or even Desktop) since 9.04 even using the text-based installer. I boot from a USB stick created by Unetbootin (I also tried other methods such as startup disk creator with no difference). On the Server installer, it gets to "Detecting Hardware" (the second one about disks and all other hardware, not network hardware) and then either hangs at 0% (waited 24 hours), or reboots after a minute or two. My system (late 2007): ASUS P5NSLI motherboard Intel Core 2 Duo E6600 2.4Ghz 2 x 1GB Corsair 667MHz RAM nVidia GeForce 6600 I have unplugged everything (including the only hard disk, CD-ROMs and floppy). I have only one stick of RAM (tried each one to no avail) and am booting the installer from a USB stick (booting from CD-ROM yields the same problem). I also tried several of the boot options (nomodeset, nousb, acpi=off, noapic, i915.modeset=1/0, xforcevesa) in all combinations) to no avail. The only active parts of my system are the video card, mouse, keyboard and USB stick. I have also updated the BIOS to the most recent version. (FWIW, on the Desktop installer, I get a black screen after hitting the Install option.) Even after removing "quiet" I am unable to see what kernel panic is occurring (or not occurring) to cause the install to crash. I am only able to save the debug logs via a simple webserver in the installer. After the last line (I repeatedly refreshed), the server stops responding and the installer hangs or reboots: Jan 2 01:04:03 main-menu[302]: INFO: Menu item 'disk-detect' selected Jan 2 01:04:04 kernel: [ 309.154372] sata_nv 0000:00:0e.0: version 3.5 Jan 2 01:04:04 kernel: [ 309.154409] sata_nv 0000:00:0e.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.154531] sata_nv 0000:00:0e.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.164442] scsi0 : sata_nv Jan 2 01:04:04 kernel: [ 309.167610] scsi1 : sata_nv Jan 2 01:04:04 kernel: [ 309.167762] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 10 Jan 2 01:04:04 kernel: [ 309.167774] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 10 Jan 2 01:04:04 kernel: [ 309.167948] sata_nv 0000:00:0f.0: Using SWNCQ mode Jan 2 01:04:04 kernel: [ 309.168071] sata_nv 0000:00:0f.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.171931] scsi2 : sata_nv Jan 2 01:04:04 kernel: [ 309.173793] scsi3 : sata_nv Jan 2 01:04:04 kernel: [ 309.173943] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 11 Jan 2 01:04:04 kernel: [ 309.173954] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 11 Jan 2 01:04:04 kernel: [ 309.174061] pata_amd 0000:00:0d.0: version 0.4.1 Jan 2 01:04:04 kernel: [ 309.174160] pata_amd 0000:00:0d.0: setting latency timer to 64 Jan 2 01:04:04 kernel: [ 309.177045] scsi4 : pata_amd Jan 2 01:04:04 kernel: [ 309.178628] scsi5 : pata_amd Jan 2 01:04:04 kernel: [ 309.178801] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 Jan 2 01:04:04 kernel: [ 309.178811] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface eth0 Jan 2 01:04:04 net/hw-detect.hotplug: Detected hotpluggable network interface lo Jan 2 01:04:04 kernel: [ 309.485062] ata3: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:04 kernel: [ 309.633094] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Jan 2 01:04:04 kernel: [ 309.641647] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133 Jan 2 01:04:04 kernel: [ 309.641658] ata1.00: 1953525168 sectors, multi 1: LBA48 NCQ (depth 31/32) Jan 2 01:04:04 kernel: [ 309.657614] ata1.00: configured for UDMA/133 Jan 2 01:04:04 kernel: [ 309.657969] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5 Jan 2 01:04:04 kernel: [ 309.658482] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 2 01:04:04 kernel: [ 309.658588] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) Jan 2 01:04:04 kernel: [ 309.658812] sd 0:0:0:0: [sda] Write Protect is off Jan 2 01:04:04 kernel: [ 309.658823] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 Jan 2 01:04:04 kernel: [ 309.658918] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Jan 2 01:04:04 kernel: [ 309.675630] sda: sda1 sda2 Jan 2 01:04:04 kernel: [ 309.676440] sd 0:0:0:0: [sda] Attached SCSI disk Jan 2 01:04:05 kernel: [ 309.969102] ata2: SATA link down (SStatus 0 SControl 300) Jan 2 01:04:05 kernel: [ 310.281137] ata4: SATA link down (SStatus 0 SControl 300) Anybody have any additional ideas I could try? I am getting ready to just toss the motherboard.

  Read the article

• How to Browse Without a Trace with an Ubuntu Live CD

  - by Trevor Bekolay

  No matter how diligently you clear your cache and erase your history, web browsing leaves traces on your computer. If you need keep your browsing private, then an Ubuntu Live CD is the answer. The key to this trick is that the Live CD environment runs completely in RAM, so things like your cache, cookies, and history don’t get saved to a persistent storage location. On a hard drive, even deleted files can be recovered, but once a computer is turned off the data stored in RAM is unrecoverable. In addition, since the Ubuntu Live CD environment is the same no matter what computer you use it on, there’s very little identifying information that a website can use to track you! The first step is to either burn an Ubuntu Live CD, or prepare a non-persistent Ubuntu USB flash drive. Ubuntu treats non-persistent flash drives like CDs, so files will not be written to it, but if you’re paranoid, then using a physical CD ensures that nothing gets written to a storage device. Boot up from the CD or flash drive, and choose to Run Ubuntu from the CD or flash drive if prompted (for more detailed instructions on booting from a CD or USB drive, see this article, or our guide on booting from a flash drive even if your BIOS won’t let you). Once the graphical Ubuntu environment comes up, you can click on the Firefox icon at the top of the screen to start browsing. If your browsing requires Flash, then you can install it by clicking on System at the top-left of the screen, then Administration > Synaptic Package Manager. Click on Settings at the top of the Synaptic window, and then select Repositories. Add a check in the checkbox with the label ending in “multiverse”. Click Close. Click the Reload button in the main Synaptic window. The list of available packages will reload. When they’ve reloaded, type “restricted” in the Quick search box. Right-click on ubuntu-restricted-extras and select Mark for Installation. It will note a number of other packages that will be installed. This list includes audio and video codecs, so after installing these, you should be able to play downloaded movies and songs. Click Mark to accept the installation of these other packages. Once you return to the main Synaptic window, click the Apply button and go through the dialogs to finish the installation of Flash and the other useful packages. If you open up Firefox now, you’ll have no problems using websites that use Flash. When you’re done browsing and shut down or restart your computer, all traces of your web browsing will be gone. It’s a bit of work compared to just using a privacy-centric browser, but if it’s very important that your browsing leave no traces on your hard drive, an Ubuntu Live CD is your best bet. Download Ubuntu Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDAdding extra Repositories on UbuntuHow to Add a Program to the Ubuntu Startup List (After Login)How to install Spotify in Ubuntu 9.10 using WineInstalling PHP4 and Apache on Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 2010 World Cup Schedule Boot Snooze – Reboot and then Standby or Hibernate Customize Everything Related to Dates, Times, Currency and Measurement in Windows 7 Google Earth replacement Icon (Icons we like) Build Great Charts in Excel with Chart Advisor tinysong gives a shortened URL for you to post on Twitter (or anywhere)

  Read the article

• Intel I217LM ethernet controller not detected by Ubuntu 12.04LTS

  - by Alexandr Kurilin

  My last installation of Ubuntu 12.04 on a machine using an ASUS Q87M-E motherboard with an Intel I217LM Ethernet controller has failed to detect the ethernet card. The only thing displayed by ifconfig -a is the loopback. I double-checked in the BIOS, and the controller should be online. $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lspci 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Haswell HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation Lynx Point KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 153a (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point HD Audio Controller (rev 04) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-Port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) $ lsmod Module Size Used by vesafb 13844 1 snd_hda_codec_realtek 224173 1 arc4 12529 2 joydev 17693 0 usbhid 47238 0 hid 99636 1 usbhid rfcomm 47604 0 rt73usb 31735 0 crc_itu_t 12707 1 rt73usb rt2x00usb 20808 1 rt73usb rt2x00lib 55326 2 rt73usb,rt2x00usb mac80211 506862 2 rt2x00usb,rt2x00lib cfg80211 205774 2 rt2x00lib,mac80211 eeepc_wmi 13109 0 bnep 18281 2 asus_wmi 24456 1 eeepc_wmi sparse_keymap 13890 1 asus_wmi psmouse 97485 0 bluetooth 180153 10 rfcomm,bnep ppdev 17113 0 snd_hda_intel 33719 6 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_seq_midi 13324 0 snd_hwdep 17764 1 snd_hda_codec snd_rawmidi 30748 1 snd_seq_midi serio_raw 13211 0 snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq parport_pc 32866 1 snd 79041 21 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_rawmidi,snd_pcm,snd_seq,snd_timer,snd_seq_device video 19651 0 soundcore 15091 1 snd wmi 19256 1 asus_wmi snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp $ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1091 errors:0 dropped:0 overruns:0 frame:0 TX packets:1091 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:80048 (80.0 KB) TX bytes:80048 (80.0 KB) wlan0 Link encap:Ethernet HWaddr 00:fd:07:91:a8:b9 inet addr:172.16.42.4 Bcast:172.16.42.255 Mask:255.255.255.0 inet6 addr: fe80::2fd:7ff:fe91:a8b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56644 errors:0 dropped:0 overruns:0 frame:0 TX packets:36417 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:85270918 (85.2 MB) TX bytes:3413849 (3.4 MB) additionally, running sudo lshw -C network returns: *-network UNCLAIMED description: Ethernet Controller [...] I'm pretty stumped at this point. This doesn't sound like a very uncommon ethernet controller and I figured it would be picked up by the system. Does anybody have advice for how to deal with this? Anything specific I should look into to figure out what could be causing this? Edit: It seems that following the guide on the Intel e1000e drivers page allowed the card to start working. Is this a real fix or is there a better way?

  Read the article

• help: cannot make ubuntu 64-bit v12.04 install work

  - by honestann

  I decided it was time to update my ubuntu (single boot) computer from 64-bit v10.04 to 64-bit v12.04. Unfortunately, for some reason (or reasons) I just can't make it work. Note that I am attempting a fresh install of 64-bit v12.04 onto a new 3TB hard disk, not an upgrade of the 1TB hard disk that has contained my 64-bit v10.04 installation. To perform the attempted install of v12.04 I unplug the SATA cable from the 1TB drive and plug it into the 3TB drive (to avoid risking damage to my working v10.04 installation). I downloaded the ubuntu 64-bit v12.04 install DVD ISO file (~1.6 GB) from the ubuntu releases webpage and burned it onto a DVD. I have downloaded the DVD ISO file 3 times and burned 3 of these installation DVDs (twice with v10.04 and once with my winxp64 system), but none of them work. I run the "check disk" on the DVDs at the beginning of the installation process to assure the DVD is valid. I also tried to install on two older 250GB seagate drives in the same computer. During every attempt I plug the same SATA cable (sda) into only one disk drive (the 3TB or one of the 250GB drives) and leave the other disk drives unconnected (for simplicity). Installation takes about 30 minutes on the 250GB drives, and about 60 minutes on the 3TB drive - not sure why. When I install on the 250GB drives, the install process finishes, the computer reboots (after the install DVD is removed), but I get a grub error 15. It is my understanding that 64-bit ubuntu (and 64-bit linux in general) has no problem with 3TB disk drives. In the BIOS I have tried having EFI set to "enabled" and "auto" with no apparent difference (no success). I have tried partitioning the drive in a few ways to see if that makes a difference, but so far it has not mattered. Typically I manually create partitions something like this: 8GB swap 8GB /boot ext4 3TB / ext4 But I've also tried the following, just in case it matters: 100MB boot efi 8GB swap 8GB /boot ext4 3TB / ext4 Note: In the partition dialog I specify bootup on the same drive I am partitioning and installing ubuntu v12.04 onto. It is a VERY DANGEROUS FACT that the default for this always comes up with the wrong drive (some other drive, generally the external drive). Unless I'm stupid or misunderstanding something, this is very wrong and very dangerous default behavior. Note: If I connect the SATA cable to the 1TB drive that has been my ubuntu 64-bit v10.04 system drive for the past 2 years, it boots up and runs fine. I guess there must be a log file somewhere, and maybe it gives some hints as to what the problem is. I should be able to boot off the 1TB drive with the 3TB drive connected as a secondary (non-boot) drive and get the log file, assuming there is one and someone tells me the name (and where to find it if the name is very generic). After installation on the 3TB drive completes and the system reboots, the following prints out on a black screen: Loading Operating System ... Boot from CD/DVD : Boot from CD/DVD : error: unknown filesystem grub rescue Note: I have two DVD burners in the system, hence the duplicate line above. The same install and reboot on the 250GB drives generates "grub error 15". Sigh. Any ideas? ========== motherboard == gigabyte 990FXA-UD7 CPU == AMD FX-8150 8-core bulldozer @ 3.6 GHz RAM == 8GB of DDR3 in 2 sticks (matched pair) HDD == seagate 3TB SATA3 @ 7200 rpm (new install 64-bit v12.04) HDD == seagate 1TB SATA3 @ 7200 rpm (current install 64-bit v10.04) GPU == nvidia GTX-285 ??? == no overclocking or other funky business USB == external seagate 2TB HDD for making backups DVD == one bluray burner (SATA) DVD == one DVD burner (SATA) The current ubuntu 64-bit v10.04 system boots and runs fine on a seagate 1TB.

  Read the article

• How To Quickly Reboot Directly from Windows 7 to XP, Vista, or Ubuntu

  - by The Geek

  One of the biggest annoyances with a dual-boot system is having to wait for your PC to reboot to select the operating system you want to switch to, but there’s a simple piece of software that can make this process easier. This guest article was written by Ryan Dozier from the Doztech tech blog. With a small piece of software called iReboot we can skip the above step all together and instantly reboot into the operating system we want right from Windows. Their description says: “Instead of pressing restart, waiting for Windows to shut down, waiting for your BIOS to post, then selecting the operating system you want to boot into (within the bootloader time-limit!); you just select that entry from iReboot and let it do the rest!” Don’t worry about iReboot reconfiguring  your bootloader or any dual boot configuration you have. iReboot will only boot the selected operating system once and go back to your default settings. Using iReboot iReboot is quick and easy to install. Just download it, link below, run through the setup and select the default configuration. iReboot will automatically figure out what operating systems you have installed and appear in the taskbar. Go over to the taskbar and right click on the iReboot icon and select which operating system you want to reboot into. This method will add a check mark on the operating system you want to boot into. On your next reboot the system will automatically load your choice and skip the Windows Boot Manager. If you want to reboot automatically just select “Reboot on Selection” in the iReboot menu.   To be even more productive, you can install iReboot into each Windows operating system to quickly access the others with a few simple clicks.   iReboot does not work in Linux so you will have to reboot manually. Then wait for the Windows Boot Manager to load and select your operating system.   Conclusion iReboot works on  Windows XP, Windows Vista,  and Windows 7 as well as 64 bit versions of these operating systems. Unfortunately iReboot is only available for Windows but you can still use its functionality in Windows to quickly boot up your Linux machine. A simple reboot in Linux will take you back to Windows Boot Manager. Download iReboot from neosmart.net Editor’s note: We’ve not personally tested this software over at How-To Geek, but Neosmart, the author of the software, generally makes quality stuff. Still, you might want to test it out on a test machine first. If you’ve got any experience with this software, please be sure to let your fellow readers know in the comments. Similar Articles Productive Geek Tips Restart the Ubuntu Gnome User Interface QuicklyKeyboard Ninja: 21 Keyboard Shortcut ArticlesTest Your Computer’s Memory Using Windows Vista Memory Diagnostic ToolEnable or Disable UAC From the Windows 7 / Vista Command LineSet Windows as Default OS when Dual Booting Ubuntu TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Home Networks – How do they look like & the problems they cause Check Your IMAP Mail Offline In Thunderbird Follow Finder Finds You Twitter Users To Follow Combine MP3 Files Easily QuicklyCode Provides Cheatsheets & Other Programming Stuff Download Free MP3s from Amazon

  Read the article

• MacGyver Moments

  - by Geoff N. Hiten

  Denny Cherry tagged me to write about my best MacGyver Moment.  Usually I ignore blogosphere fluff and just use this space to write what I think is important.  However, #MVP10 just ended and I have a stronger sense of community.  Besides, where else would I mention my second best Macgyver moment was making a BIOS jumper out of a soda can.  Aluminum is conductive and I didn't have any real jumpers lying around. My best moment is probably my entire home computer network.  Every system but one is hand-built, usually cobbled together out of spare parts and 'adapted' from its original purpose. My Primary Domain Controller is a Dell 2300.   The Service Tag indicates it was shipped to the original owner in 1999.  Box has a PERC/1 RAID controller.  I acquired this from a previous employer for $50.  It runs Windows Server 2003 Enterprise Edition.  Does DNS, DHCP, and RADIUS services as a bonus.  RADIUS authentication is used for VPN and Wireless access.  It is nice to sign in once and be done with it. The Secondary Domain Controller is an old desktop.  Dual P-III 933 with some extra drives. My VPN box is a P-II 250 with 384MB of RAM and a 21 GB hard drive.  I did a P-to-V to my Hyper-V box a year or so ago and retired the hardware again.  Dynamic DNS lets me connect no matter how often Comcast shuffles my IP. The Hyper-V box is a desktop system with 8GB RAM and an AMD Athlon 5000+ processor.  Cost me less than $500 to put together nearly two years ago.  I reasoned that if Vista and Windows 2008 were the same code then Vista 64-bit certified meant the drivers for Vista would load into Windows 2008.  Turns out I was right. Later I added three 1TB drives but wasn't too happy with how that turned out.  I recovered two of the drives yesterday and am building an iSCSI storage unit. (Much thanks to Starwind.  Great product).  I am using an old AMD 1.1GhZ box with 1.5 GB RAM (cobbled together from three old PCs) as my storave server.  The Hyper-V box is slated for an OS rebuild to 2008 R2 once I get the storage system worked out.  maybe in a week or two. A couple of DLink Gigabit switches ties everything together. Add in the Vonage box, the three PCs, the Wireless-N Access Point, the two notebooks and the XBox and you have gone from MacGyver to darn near Rube Goldberg. The only thing I really spend money on is power supplies and fans.  I buy top-of-the-line for both. I even pull and crimp my own cables. Oh, and if my kids hose up a PC, I have all of their data on a server elsewhere.  Every PC and laptop is pretty much interchangable for email and basic workstation tasks.  That helps a lot too. Of course I will tag SQLVariant.

  Read the article

• LSI SAS 9240-8i on Ubuntu 12.04 Hangs on Modprobe

  - by Francois Stark

  I used the LSI 9240-8i card on a smaller Intel motherboard with no problems in Ubuntu, with ZFS. However, we rebuilt the server to allow for more disks, using the ASROCK X79 Extreme 11 motherboard. It has 7 PCIe slots, and a LSI 2008 on-board. At first I thought the LSI 9240, when plugged in to PCIe, clashed with the on-board LSI 2008. Every time I plugged in the LSI 9240, modprobe would hang. Then I completely disabled the on-board LSI 2008, and the problem persisted. Last night it booted perfectly ONCE - all LSI cards and connected disks visible... However, all subsequent reboots failed. Both LSI cards' bios scans appear and they both see the disks connected to them, but Ubuntu modprobe hangs. Some selected dmesg lines, with both LSI cards enabled: [ 190.752100] megasas: [ 0]waiting for 1 commands to complete [ 195.772071] megasas: [ 5]waiting for 1 commands to complete [ 200.792079] megasas: [10]waiting for 1 commands to complete [ 205.812078] megasas: [15]waiting for 1 commands to complete [ 210.832037] megasas: [20]waiting for 1 commands to complete [ 215.852077] megasas: [25]waiting for 1 commands to complete [ 220.872072] megasas: [30]waiting for 1 commands to complete [ 225.892078] megasas: [35]waiting for 1 commands to complete [ 230.912086] megasas: [40]waiting for 1 commands to complete [ 235.932075] megasas: [45]waiting for 1 commands to complete [ 240.306157] usb 2-1.5: USB disconnect, device number 7 [ 240.952076] megasas: [50]waiting for 1 commands to complete [ 240.960034] INFO: task modprobe:233 blocked for more than 120 seconds. [ 240.960055] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 240.960067] modprobe D ffffffff81806200 0 233 146 0x00000004 [ 240.960075] ffff880806ae3b48 0000000000000086 ffff880806ae3ae8 ffffffff8101adf3 [ 240.960083] ffff880806ae3fd8 ffff880806ae3fd8 ffff880806ae3fd8 0000000000013780 [ 240.960090] ffffffff81c0d020 ffff880806acae00 ffff880806ae3b58 ffff880808961720 [ 240.960096] Call Trace: [ 240.960107] [<ffffffff8101adf3>] ? native_sched_clock+0x13/0x80 [ 240.960116] [<ffffffff816579cf>] schedule+0x3f/0x60 [ 240.960137] [<ffffffffa00093f5>] megasas_issue_blocked_cmd+0x75/0xb0 [megaraid_sas] [ 240.960144] [<ffffffff8108aa50>] ? add_wait_queue+0x60/0x60 [ 240.960154] [<ffffffffa000a6c9>] megasas_get_seq_num+0xd9/0x260 [megaraid_sas] [ 240.960164] [<ffffffffa000ab31>] megasas_start_aen+0x31/0x60 [megaraid_sas] [ 240.960174] [<ffffffffa00136f1>] megasas_probe_one+0x69a/0x81c [megaraid_sas] [ 240.960182] [<ffffffff813345bc>] local_pci_probe+0x5c/0xd0 [ 240.960189] [<ffffffff81335e89>] __pci_device_probe+0xf9/0x100 [ 240.960197] [<ffffffff8130ce6a>] ? kobject_get+0x1a/0x30 [ 240.960205] [<ffffffff81335eca>] pci_device_probe+0x3a/0x60 [ 240.960212] [<ffffffff813f5278>] really_probe+0x68/0x190 [ 240.960217] [<ffffffff813f5505>] driver_probe_device+0x45/0x70 [ 240.960223] [<ffffffff813f55db>] __driver_attach+0xab/0xb0 [ 240.960227] [<ffffffff813f5530>] ? driver_probe_device+0x70/0x70 [ 240.960233] [<ffffffff813f5530>] ? driver_probe_device+0x70/0x70 [ 240.960237] [<ffffffff813f436c>] bus_for_each_dev+0x5c/0x90 [ 240.960243] [<ffffffff813f503e>] driver_attach+0x1e/0x20 [ 240.960248] [<ffffffff813f4c90>] bus_add_driver+0x1a0/0x270 [ 240.960255] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960260] [<ffffffff813f5b46>] driver_register+0x76/0x140 [ 240.960266] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960271] [<ffffffff81335b66>] __pci_register_driver+0x56/0xd0 [ 240.960277] [<ffffffffa001e000>] ? 0xffffffffa001dfff [ 240.960286] [<ffffffffa001e09e>] megasas_init+0x9e/0x1000 [megaraid_sas] [ 240.960294] [<ffffffff81002040>] do_one_initcall+0x40/0x180 [ 240.960301] [<ffffffff810a82fe>] sys_init_module+0xbe/0x230 [ 240.960307] [<ffffffff81661ec2>] system_call_fastpath+0x16/0x1b [ 240.960314] INFO: task scsi_scan_7:349 blocked for more than 120 seconds.

  Read the article

• ALC889 - GA-P55-UD4 -no sound - Ubuntu 11.10

  - by george

  I have computer with a Gigabyte P55A-UD4 motherboard. I have on-board audio - Realtek ALC889. I am using Ubuntu 11.10 and have no sound. please please heeeelp :). i have tryed to install high definition audio codecs from realtek but it doesn't work. in bios the azalia codec is turned on. ps : sorry for my english. 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 12) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1a.1 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1a.2 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1a.7 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1c.6 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 7 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1d.1 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1d.2 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1d.3 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller (rev 06) 00:1d.7 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) 03:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 03:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 04:00.0 IDE interface: Marvell Technology Group Ltd. Device 91a3 (rev 11) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 06:03.0 IDE interface: Integrated Technology Express, Inc. IT8213 IDE Controller 06:07.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) 3f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) 3f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) 3f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) 3f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) 3f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) 3f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) aplay -l karta 0: Intel [HDA Intel], urzadzenie 0: ALC889 Analog [ALC889 Analog] Urzadzenia podrzedne: 1/1 Urzadzenie podrzedne #0: subdevice #0 karta 0: Intel [HDA Intel], urzadzenie 1: ALC889 Digital [ALC889 Digital] Urzadzenia podrzedne: 1/1 Urzadzenie podrzedne #0: subdevice #0 karta 1: NVidia [HDA NVidia], urzadzenie 3: HDMI 0 [HDMI 0] Urzadzenia podrzedne: 1/1 Urzadzenie podrzedne #0: subdevice #0 karta 1: NVidia [HDA NVidia], urzadzenie 7: HDMI 0 [HDMI 0] Urzadzenia podrzedne: 1/1 Urzadzenie podrzedne #0: subdevice #0 karta 1: NVidia [HDA NVidia], urzadzenie 8: HDMI 0 [HDMI 0] Urzadzenia podrzedne: 1/1 Urzadzenie podrzedne #0: subdevice #0 karta 1: NVidia [HDA NVidia], urzadzenie 9: HDMI 0 [HDMI 0] Urzadzenia podrzedne: 1/1 Urzadzenie podrzedne #0: subdevice #0

  Read the article

• No sound lenovo t60 alsa ad1981 iec958

  - by Nate

  Any help on getting the sound to come through my lenovo t60 build in speakers, headphones, or mic would greatly be appreciated. The three buttons to increase, decrease sound seem to work. Bios has sound card enabled and the buttons beep when pressed. When going to Utube or playing music, no sound is heard. Thanks Nate Feb 23 - Didn't see anything specific in the sys logs with Rhythmbox when connecting my ipod. Rhythmbox is playing, but still no sound. Here is the syslog details for today. Output is set to analog output. Feb 23 17:42:32 itgis01398 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'. Feb 23 17:42:33 itgis01398 rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="824" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'. Feb 23 17:42:49 itgis01398 anacron[968]: Job `cron.daily' terminated Feb 23 17:42:49 itgis01398 anacron[968]: Job `cron.weekly' started Feb 23 17:42:49 itgis01398 anacron[12067]: Updated timestamp for job `cron.weekly' to 2011-02-23 Feb 23 17:42:53 itgis01398 anacron[968]: Job `cron.weekly' terminated Feb 23 17:42:53 itgis01398 anacron[968]: Normal exit (2 jobs run) Feb 23 18:01:19 itgis01398 kernel: [ 2731.324067] usb 1-5: new high speed USB device using ehci_hcd and address 3 Feb 23 18:01:19 itgis01398 kernel: [ 2731.482879] Initializing USB Mass Storage driver... Feb 23 18:01:19 itgis01398 kernel: [ 2731.483061] usb-storage 1-5:1.0: Quirks match for vid 05ac pid 1205: 10 Feb 23 18:01:19 itgis01398 kernel: [ 2731.483116] scsi6 : usb-storage 1-5:1.0 Feb 23 18:01:19 itgis01398 kernel: [ 2731.483306] usbcore: registered new interface driver usb-storage Feb 23 18:01:19 itgis01398 kernel: [ 2731.483310] USB Mass Storage support registered. Feb 23 18:01:20 itgis01398 kernel: [ 2732.481116] scsi 6:0:0:0: Direct-Access Apple iPod 1.62 PQ: 0 ANSI: 0 Feb 23 18:01:20 itgis01398 kernel: [ 2732.482466] sd 6:0:0:0: Attached scsi generic sg2 type 0 Feb 23 18:01:20 itgis01398 kernel: [ 2732.485095] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.485110] sd 6:0:0:0: [sdb] 7999487 512-byte logical blocks: (4.09 GB/3.81 GiB) Feb 23 18:01:20 itgis01398 kernel: [ 2732.487933] sd 6:0:0:0: [sdb] Write Protect is off Feb 23 18:01:20 itgis01398 kernel: [ 2732.487941] sd 6:0:0:0: [sdb] Mode Sense: 64 00 00 08 Feb 23 18:01:20 itgis01398 kernel: [ 2732.487947] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.489927] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.491150] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.491163] sdb: sdb1 sdb2 Feb 23 18:01:20 itgis01398 kernel: [ 2732.510428] sd 6:0:0:0: [sdb] Adjusting the sector count from its reported value: 7999488 Feb 23 18:01:20 itgis01398 kernel: [ 2732.511288] sd 6:0:0:0: [sdb] Assuming drive cache: write through Feb 23 18:01:20 itgis01398 kernel: [ 2732.511297] sd 6:0:0:0: [sdb] Attached SCSI removable disk Feb 23 18:01:21 itgis01398 kernel: [ 2733.746675] FAT: invalid media value (0x2f) Feb 23 18:01:21 itgis01398 kernel: [ 2733.746682] VFS: Can't find a valid FAT filesystem on dev sdb1. Feb 23 18:01:22 itgis01398 upstart-udev-bridge[330]: Env must be KEY=VALUE pairs Feb 23 18:02:07 itgis01398 kernel: [ 2780.115826] sd 6:0:0:0: [sdb] Unhandled sense code Feb 23 18:02:07 itgis01398 kernel: [ 2780.115835] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Feb 23 18:02:07 itgis01398 kernel: [ 2780.115844] sd 6:0:0:0: [sdb] Sense Key : Medium Error [current] Feb 23 18:02:07 itgis01398 kernel: [ 2780.115855] Info fld=0x0 Feb 23 18:02:07 itgis01398 kernel: [ 2780.115859] sd 6:0:0:0: [sdb] Add. Sense: Unrecovered read error Feb 23 18:02:07 itgis01398 kernel: [ 2780.115870] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 08 fd e9 00 00 f0 00 Feb 23 18:02:07 itgis01398 kernel: [ 2780.115892] end_request: I/O error, dev sdb, sector 589289 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351464] sd 6:0:0:0: [sdb] Unhandled sense code Feb 23 18:02:49 itgis01398 kernel: [ 2821.351473] sd 6:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Feb 23 18:02:49 itgis01398 kernel: [ 2821.351482] sd 6:0:0:0: [sdb] Sense Key : Medium Error [current] Feb 23 18:02:49 itgis01398 kernel: [ 2821.351493] Info fld=0x0 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351497] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information Feb 23 18:02:49 itgis01398 kernel: [ 2821.351507] sd 6:0:0:0: [sdb] CDB: Read(10): 28 00 00 08 fe d9 00 00 10 00 Feb 23 18:02:49 itgis01398 kernel: [ 2821.351530] end_request: I/O error, dev sdb, sector 589529 Feb 23 18:17:01 itgis01398 CRON[12709]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) volume is all of the way up.

  Read the article

• Integrated webcam in lenovo t410 not working with 12.04

  - by kristianp

  I have a Lenovo T410 with an inbuilt webcam and I haven't been able to get the webcam working. I tried skype, cheese, both just give me a black window. The microphone works fine with skype, by the way. Can anyone provide any clues please? The webcam is enabled in the bios, but there is no light indicating the webcam is on (not sure if there should be, though). I tried this on Kubuntu 11.10 and have upgraded to 12.04 with the same results. The Fn-F6 keyboard combination doens't seem to do anything either. EDIT: I got the webcam replaced, it looks like it was a hardware problem, because it works fine now. Thanks guys. $ ls /dev/v4l/* /dev/v4l/by-id: usb-Chicony_Electronics_Co.__Ltd._Integrated_Camera-video-index0 /dev/v4l/by-path: pci-0000:00:1a.0-usb-0:1.6:1.0-video-index0 And lsusb: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 005: ID 17ef:480f Lenovo Integrated Webcam [R5U877] Bus 002 Device 003: ID 05c6:9204 Qualcomm, Inc. Bus 002 Device 004: ID 17ef:1003 Lenovo Integrated Smart Card Reader Here is the output from guvcview, minus lots of lines describing the available capture formats. It says "unable to start with minimum setup. Please reconnect your camera.". guvcview 1.5.3 ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, .... { discrete: width = 1600, height = 1200 } Time interval between frame: 1/15, vid:17ef pid:480f driver:uvcvideo checking format: 1196444237 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } .... vid:17ef pid:480f driver:uvcvideo checking format: 1448695129 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! ERROR: Minimum Setup Failed. Exiting... VIDIOC_REQBUFS - Failed to delete buffers: Invalid argument (errno 22) cleaned allocations - 100% Closing portaudio ...OK Terminated.

  Read the article

• Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

  - by Tom

  I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

  Read the article

• Converting a PV vm back into an HVM vm

  - by wim.coekaerts

  I have been doing some Oracle VM benchmark stuff in the last week or 2 in my off hours and yesterday I wanted to convert one of my VMs that was based on a paravirt kernel into a vm that just boots as a regular hardware virt VM with a standard x86-64 kernel. It took me a little while to figure out the fastest way so now that I have it pretty much down I wanted to share the steps. A PV kernel uses pygrub and a paravirt kernel image that lives on the vm image virtual disk. since this disk image does not have to be bootable it doesn't contain a boot sector and if you just restart the VM in hvm mode the virtual bios will just not do much as it can't start the boot process from disk The first thing I do is make a backup of my vm.cfg file :-) and then edit it as follows : the original file contains : bootloader = '/usr/bin/pygrub' I replace that with : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' kernel = '/usr/lib/xen/boot/hvmloader' then changing the disk files. I change my xvd disks to hd disks and I copy over the iso image of my instal lDVD. In the case of my VM template it was based on OL5U4 So I downloaded Enterprise-R5-U4-Server-x86_64-dvd.iso and added it as a cd device. disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,xvda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,xvdb,w', ] to disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,hda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,hdb,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Enterprise-R5-U4-Server-x86_64-dvd.iso, hdc:cdrom,r', ] boot='d' for the network devices (vifs) I change : vif = ['bridge=xenbr2,type=netfront'] to vif = ['bridge=xenbr2,type=ioemu'] That should do it. Next, inside the VM, I copy over the regular kernel rpm that I want to end up running in hvm mode. In this example case it was : kernel-2.6.18-164.0.0.0.1.el5.x8664.rpm. I will use that later on in the process. I put this kernel simply in /root At this point I just start the vm with xm create vm.cfg and start my vnc console to the vm console. Oracle Linux will boot from the iso image, I just go through the install steps and click on UPgrade existing (not re-install). Because the VM is the same as the ISO the install won't actually do anything and it will run through instantly. When the "Reboot" button pops up, don't reboot. Switch to the command prompt console. hi alt-f2 to go to the shell prompt. Now it's easy : umount /mnt/sysimage/boot cd /mnt/sysimage chroot . mount /dev/hda1 (if that was your /boot partition) export PATH=/sbin:$PATH (just to clean that up) edit /etc/modprobe.conf and comment out the xen modules (just put a # in front) Install grub. if your /boot is hda1 then that is (hd0,0) $ grub root (hd0,0) setup (hd0) exit grub now you have a good bootsector, grub installed and you have your grub.conf file Install the new kernel cd root (this is your old /root in your pv image) rpm -ivh remove (or comment out) boot='d' in your vm.cfg restart the VM and you should be good to go, regular grub should start and load your environment. Caveats : this assumes you used labels for your filesystems. if /etc/fstab were to have devices listed then you would have to rename these device before rebooting as well. If you had a /dev/xvda disk then this would be /dev/hda or /dev/sda. All in all it is a relatively short and simple process.

  Read the article

• Converting a PV vm back into an HVM vm

  - by wim.coekaerts

  I have been doing some Oracle VM benchmark stuff in the last week or 2 in my off hours and yesterday I wanted to convert one of my VMs that was based on a paravirt kernel into a vm that just boots as a regular hardware virt VM with a standard x86-64 kernel. It took me a little while to figure out the fastest way so now that I have it pretty much down I wanted to share the steps. A PV kernel uses pygrub and a paravirt kernel image that lives on the vm image virtual disk. since this disk image does not have to be bootable it doesn't contain a boot sector and if you just restart the VM in hvm mode the virtual bios will just not do much as it can't start the boot process from disk The first thing I do is make a backup of my vm.cfg file :-) and then edit it as follows : the original file contains : bootloader = '/usr/bin/pygrub' I replace that with : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' kernel = '/usr/lib/xen/boot/hvmloader' then changing the disk files. I change my xvd disks to hd disks and I copy over the iso image of my instal lDVD. In the case of my VM template it was based on OL5U4 So I downloaded Enterprise-R5-U4-Server-x86_64-dvd.iso and added it as a cd device. disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,xvda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,xvdb,w', ] to disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,hda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,hdb,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Enterprise-R5-U4-Server-x86_64-dvd.iso, hdc:cdrom,r', ] boot='d' for the network devices (vifs) I change : vif = ['bridge=xenbr2,type=netfront'] to vif = ['bridge=xenbr2,type=ioemu'] That should do it. Next, inside the VM, I copy over the regular kernel rpm that I want to end up running in hvm mode. In this example case it was : kernel-2.6.18-164.0.0.0.1.el5.x8664.rpm. I will use that later on in the process. I put this kernel simply in /root At this point I just start the vm with xm create vm.cfg and start my vnc console to the vm console. Oracle Linux will boot from the iso image, I just go through the install steps and click on UPgrade existing (not re-install). Because the VM is the same as the ISO the install won't actually do anything and it will run through instantly. When the "Reboot" button pops up, don't reboot. Switch to the command prompt console. hi alt-f2 to go to the shell prompt. Now it's easy : umount /mnt/sysimage/boot cd /mnt/sysimage chroot . mount /dev/hda1 (if that was your /boot partition) export PATH=/sbin:$PATH (just to clean that up) edit /etc/modprobe.conf and comment out the xen modules (just put a # in front) Install grub. if your /boot is hda1 then that is (hd0,0) $ grub root (hd0,0) setup (hd0) exit grub now you have a good bootsector, grub installed and you have your grub.conf file Install the new kernel cd root (this is your old /root in your pv image) rpm -ivh remove (or comment out) boot='d' in your vm.cfg restart the VM and you should be good to go, regular grub should start and load your environment. Caveats : this assumes you used labels for your filesystems. if /etc/fstab were to have devices listed then you would have to rename these device before rebooting as well. If you had a /dev/xvda disk then this would be /dev/hda or /dev/sda. All in all it is a relatively short and simple process.

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• How to get faster graphics in KVM? VNC is painfully slow with Haiku OS guest, Spice won't install and SDL doesn't work

  - by Don Quixote

  I've been coming up to speed on the Haiku operating system, an Open Source clone of BeOS 5 Pro. I'm using an Apple MacBook Pro as my development machine. Apple's BootCamp BIOS does not support more than four partitions on the internal hard drive. While I can set up extended and logical partitions, doing so will prevent any of the installed operating systems from booting. To run Haiku directly on the iron, I boot it off a USB stick. Using external storage is also helpful because I am perpetually out of filesystem space. While VirtualBox is documented to allow access to physical drives, I could not actually get it to work. Also VirtualBox can only use one of the host CPU's cores. While VB guests can be configured for more than one CPU, they are only emulated. A full build of the Haiku OS takes 4.5 under VB. I had the hope of reducing build times by using KVM instead, but it's not working nearly as well as VirtualBox did. The Linux Kernel Virtual Machine is broken in all manner of fundamental ways as seen from Haiku. But I'm a coder; maybe I could contribute to fixing some of those problems. The first problem I've got is that Haiku's video in virt-manager is quite painfully slow. When I drag Haiku windows around the desktop, they lag quite far behind where my mouse is. It's quite difficult to move a window to a precise position on the screen. Just imagine that the mouse was connected to the window title bar with a really stretchy spring. Also Haiku's mouse lags quite far behind where I have moved it. I found lots of Personal Package Archives that enable Spice from QEMU / KVM at the Ubuntu Personal Package Arhives. I tried a few of the PPAs but none of them worked; with one of them, the command "add-apt-repository" crashed with a traceback. There is a Wiki page about Spice, but it says that it only works on 64-bit. My Early 2006 MacBook Pro is 32-bit. Its Apple Model Identifier is MacBookPro1,1; these use Core Duos NOT Core 2 Duos. I don't mind building a source deb for 32-bit if I can expect it to work. Is there some reason that Spice should be 64-bit only? Does it need features of the x86_64 Instruction Set Architecture that x86 does not have? When I try using SDL from virt-manager, the configuration for Local SDL Window says "Xauth: /home/mike/.Xauthority". When I try to start my guest, virt-manager emits an error. When I Googled the error message, the usual solution was to make ~/.Xauthority readible. However, .Xauthorty does not exist in my home directory. Instead I have a $XAUTHORITY environment variable. There is no way to configure SDL in virt-manager to use $XAUTHORITY instead of ~/.Xauthority. Neither does it work to copy the value of $XAUTHORITY into the file. I am ready to scream, because I've been five fscking days trying to make KVM work for Haiku development. There is a whole lot more that is broken than the slow video. All I really want to do for now is speed up my full builds of Haiku by using "jam -j2" to use both cores in my CPU. I may try Xen next, but the last time I monkeyed with Xen it was far, far more broken than I am finding KVM to be. Just for now, I would be satisfied if there were some way to use my USB stick as a drive in VirtualBox. VB does allow me to configure /dev/sdb as a drive, but it always causes a fatal error when I try to launch the guest. Thank You For Any Advice You Can Give Me. -

  Read the article

• How do I configure WakeOnUSB properly?

  - by wishi

  How do I configure Wake-On-USB properly on a 10.04 or 10.10 Ubuntu (2.6.36 and higher if needed)? (Wake-on-USB is when the computer is asleep and for example a USB Keyboard event wakes up the machine!) The notebook is an Acer Aspire Timeline X 1830T. I don't know in which way the Linux Kernel supports the controllers. There are different ways to approach this, for example /proc/acpi/wakeup... or UDEV... or something with HAL? /proc/acpi/wakeup shows every device in S4, but I need S3. Device S-state Status Sysfs node P0P2 S4 *disabled PEGP S4 *disabled P0P1 S0 *disabled pci:0000:00:1e.0 EHC1 S4 *disabled pci:0000:00:1d.0 USB1 S4 *enabled USB2 S4 *disabled USB3 S4 *disabled USB4 S4 *disabled EHC2 S4 *disabled pci:0000:00:1a.0 USB5 S4 *disabled USB6 S4 *disabled USB7 S4 *disabled HDEF S0 *disabled pci:0000:00:1b.0 RP01 S5 *disabled pci:0000:00:1c.0 PXSX S5 *disabled pci:0000:01:00.0 RP02 S0 *disabled pci:0000:00:1c.1 PXSX S5 *disabled pci:0000:02:00.0 RP03 S0 *disabled PXSX S5 *disabled RP04 S0 *disabled PXSX S5 *disabled RP05 S0 *disabled PXSX S5 *disabled RP07 S0 *disabled PXSX S5 *disabled RP08 S0 *disabled PXSX S5 *disabled GLAN S0 *disabled PEG3 S4 *disabled PEG5 S4 *disabled PEG6 S4 *disabled SLPB S3 *enabled S4, which is Suspend-To-Disk afaik... doesn't seem to work either if I echo USB1 into the wakeup table. It just sets an S4 flag. can I get the USB ports in S3? I want to make the machine wakeup from Suspend-To-Ram (S3, ACPI standard) in case a key on my external keyboard is pressed. It only wakes up if a key on the internal Laptop keyboard is pressed... from Suspend To Ram. It seems if I plug in a USB mouse, that the USB port isn't even powered. I have no BIOS option to change this. Further specific information regarding the device: usb-devices T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 13 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=04d9 ProdID=1603 Rev=03.10 S: Manufacturer= S: Product=USB Keyboard C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid root@underwater-laptop:/# lsusb [...] Bus 001 Device 013: ID 04d9:1603 Holtek Semiconductor, Inc. Bus 001 Device 004: ID 0bda:0138 Realtek Semiconductor Corp. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub [...] If this doesn't work I have to properly explain why :( - but I think it is very hard to research this kernel internal. Any hints for good information here? I hope it's possible... I'm just looking for any solution. edit: this, waking up on USB, works on Windows! Thanks a lot, Marius

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95  | Next Page >