Search Results

Search found 6887 results on 276 pages for 'internal'.

Page 90/276 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Double Layer DVD+R burning problem - I/O Error

  - by Mehper C. Palavuzlar

  I have a modern PC (Quad Core CPU, 4 GB RAM, Win7 Home Premium 64-bit) but I have a problem with burning .dvd images to Double Layer (8.5 GB) DVDs. I wasted too many DVD+R DL discs but to no avail. Here is a short explanation of what I did: I'm using ImgBurn v2.5.0.0 (latest version). I'm trying to burn an image file (.dvd) which is together with the related .iso file in the same folder. In ImgBurn, I select the file with .dvd extension, and set writing speed to 2.4x. Burning process starts normally, but around 7% of the process, it gives a I/O Write Error, which is as follows: I wasted 3 discs (Magic, Made in Taiwan, DVD+R DL, 8.5 GB) trying the same thing. My DVD writer is LG GH22NP20 with IDE connection type. I updated its firmware from 1.04 to 2.00 but no success in burning again. Then my cousin brought his LG (an older model) which, he claims, was successful in writing DL discs with the same brand (Magic). I plugged off my LG and plugged the older one in, and tried to burn the image again. It also gave an I/O Error even without standing till 7%. I tried another burning program (CloneCD), but failed again. Then I bought other brands (TDK and VERBATIM) and tried to burn the image. Burning process started successfully, but around 14% (for Verbatim) and 25% (for TDK) failed again. Here is a screeny from ImgBurn: I've burned lots of 4.7 GB DVD+Rs and DVD-Rs successfully, even without a single error, with this LG DVD writer, but this case is very bothering for me. What should I do? Should I buy a new DVD writer other than LG? Could this be related to Windows or my hardware configuration? Thanks for your help. Edit: My burner works on my cousin's machine. So the problem must be related to my system. What could be the reason? Latest news: I borrowed an external USB DVD writer from a friend, which is PHILIPS SPD3000CC (an old model). Guess what! It's burning DVD+R DLs successfully! How come an internal DVD writer of a brand new computer system cannot burn DL DVDs? Now I'm considering buying a new internal DVD writer with not IDE, but SATA connection...

  Read the article

• could not bind socket while haproxy restart

  - by shreyas

  I m restarting HAproxy by following command haproxy -f /etc/haproxy/haproxy.cfg -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid) but i get following message [ALERT] 183/225022 (9278) : Starting proxy appli1-rewrite: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli2-insert: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli3-relais: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli4-backup: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy ssl-relay: cannot bind socket [ALERT] 183/225022 (9278) : Starting proxy appli5-backup: cannot bind socket my haproxy.cfg file looks likefollowing global log 127.0.0.1 local0 log 127.0.0.1 local1 notice #log loghost local0 info maxconn 4096 #chroot /usr/share/haproxy user haproxy group haproxy daemon #debug #quiet defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen appli1-rewrite 0.0.0.0:10001 cookie SERVERID rewrite balance roundrobin server app1_1 192.168.34.23:8080 cookie app1inst1 check inter 2000 rise 2 fall 5 server app1_2 192.168.34.32:8080 cookie app1inst2 check inter 2000 rise 2 fall 5 server app1_3 192.168.34.27:8080 cookie app1inst3 check inter 2000 rise 2 fall 5 server app1_4 192.168.34.42:8080 cookie app1inst4 check inter 2000 rise 2 fall 5 listen appli2-insert 0.0.0.0:10002 option httpchk balance roundrobin cookie SERVERID insert indirect nocache server inst1 192.168.114.56:80 cookie server01 check inter 2000 fall 3 server inst2 192.168.114.56:81 cookie server02 check inter 2000 fall 3 capture cookie vgnvisitor= len 32 option httpclose # disable keep-alive rspidel ^Set-cookie:\ IP= # do not let this cookie tell our internal IP address listen appli3-relais 0.0.0.0:10003 dispatch 192.168.135.17:80 listen appli4-backup 0.0.0.0:10004 option httpchk /index.html option persist balance roundrobin server inst1 192.168.114.56:80 check inter 2000 fall 3 server inst2 192.168.114.56:81 check inter 2000 fall 3 backup listen ssl-relay 0.0.0.0:8443 option ssl-hello-chk balance source server inst1 192.168.110.56:443 check inter 2000 fall 3 server inst2 192.168.110.57:443 check inter 2000 fall 3 server back1 192.168.120.58:443 backup listen appli5-backup 0.0.0.0:10005 option httpchk * balance roundrobin cookie SERVERID insert indirect nocache server inst1 192.168.114.56:80 cookie server01 check inter 2000 fall 3 server inst2 192.168.114.56:81 cookie server02 check inter 2000 fall 3 server inst3 192.168.114.57:80 backup check inter 2000 fall 3 capture cookie ASPSESSION len 32 srvtimeout 20000 option httpclose # disable keep-alive option checkcache # block response if set-cookie & cacheable rspidel ^Set-cookie:\ IP= # do not let this cookie tell our internal IP address #errorloc 502 http://192.168.114.58/error502.html #errorfile 503 /etc/haproxy/errors/503.http errorfile 400 /etc/haproxy/errors/400.http errorfile 403 /etc/haproxy/errors/403.http errorfile 408 /etc/haproxy/errors/408.http errorfile 500 /etc/haproxy/errors/500.http errorfile 502 /etc/haproxy/errors/502.http errorfile 503 /etc/haproxy/errors/503.http errorfile 504 /etc/haproxy/errors/504.http what is wrong with my aproach

  Read the article

• Reverse Proxy FTP traffic

  - by TonyZ

  I was wondering if anyone knew of a reverse proxy server to reverse proxy ftp traffic. I would like to run many servers on ip address, but then pass the traffic to an internal server with its own ip address. Thank you for any suggestions.

  Read the article

• ISA Server 2006 SP1 :: Allow unauthenticated users (non domain users) access to external (internet)

  - by Klaptrap

  Now that we have applied an internal to external rule blocking all users access to the internet, other than those users in a whitelist, we have the obvious issue of non authenticated users, not on our domain, i.e.; domain-less guests not being able to access the internet. Other than configuring each machine to use our alternative gateway - which would require a member of IT to be onsite everytime a guest arrives - can this be done through ISA adn AD?

  Read the article

• Intel data bus of intel 80486 and above CPU

  - by JustAGuy

  Hi, I know this might be hard question, but why does Intel 80486 and above CPUs have doubled 32 bit internal data bus? I mean, ALU is still 32bit wide, so what is that extra 32 bit bus for? Thanks.

  Read the article

• MAPS windows 2008 r2 ent vs normal windows 2008 r2 ent edition [closed]

  - by KevinOelen

  Possible Duplicate: Can you help me with my software licensing question? Microsoft action pack subscription(MAPS) offers that many internal use of softwares, especially windows server 2008 R2 Ent 1 license with 10 CALs. Total cost is 329$ But when I looking for microsoft licensing and pricing guide, windows server 2008 r2 ent edition costs 3919$ with 25 cal. Do we really need to buy windows enterprise edition?

  Read the article

• Using ClearOS as a gateway/firewall/mailserver

  - by Elzenissimo

  Hi, Just installed ClearOS on a PC to act as our firewall firstly and then to act as an internal mailserver. My question is: Can i create a mailserver that then routes the mail through to our ISP mail server without having to contact the ISP and gain MX records etc..? We are a small business (5 PCs + dataserver) and the reason this is interesting is because we need to keep a record of outgoing mails from certain users, as well as spam and virus filtering.

  Read the article

• Two network adapters on Ubuntu Server 9.10 - Can't have both working at once?

  - by Rob

  I'm trying to set up two network adapters in Ubuntu (server edition) 9.10. One for the public internet, the other a private LAN. During the install, I was asked to pick a primary network adapter (eth0 or eth1). I chose eth0, gave the installer the details listed below in the contents of /etc/network/interfaces, and carried on. I've been using this adapter with these setting for the last few days, and every thing's been fine. Today, I decide it's time to set up the local adapter. I edit the /etc/network/interfaces to add the details for eth1 (see below), and restart networking with sudo /etc/init.d/networking restart. After this, attempting to ping the machine using it's external IP address fails, but I can ping it's local IP address. If I bring eth1 down using sudo ifdown eth1, I can successfully ping the machine via it's external IP address again (but obviously not it's internal IP address). Bringing eth1 back up returns us to the original problem state: external IP not working, internal IP working. Here's my /etc/network/interfaces (I've removed the external IP information, but these settings are unchanged from when it worked) rob@rhea:~$ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary (public) network interface auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask xxx.xxx.xxx.xxx network xxx.xxx.xxx.xxx broadcast xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx # The secondary (private) network interface auto eth1 iface eth1 inet static address 192.168.99.4 netmask 255.255.255.0 network 192.168.99.0 broadcast 192.168.99.255 gateway 192.168.99.254 I then do this: rob@rhea:~$ sudo /etc/init.d/networking restart * Reconfiguring network interfaces... [ OK ] rob@rhea:~$ sudo ifup eth0 ifup: interface eth0 already configured rob@rhea:~$ sudo ifup eth1 ifup: interface eth1 already configured Then, from another machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for [external ip]: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), Back on the Ubuntu server in question: rob@rhea:~$ sudo ifdown eth1 ... and again on the other machine: C:\Documents and Settings\Rob>ping [external ip] Pinging [external ip] with 32 bytes of data: Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Reply from [external ip]: bytes=32 time<1ms TTL=63 Ping statistics for [external ip]: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms So... what am I doing wrong?

  Read the article

• How to install GNU make in Windows 7?

  - by Azhar

  I am trying to install GNU make-3.82 on Windows 7. I downloaded the make-3.82.tar.gz setup but it does not have any setup file. There is process given on GNU site. But when I reach to the folder in command prompt and after extraction write ./configure it throws error is not recognized as internal or an external command, operable program or batch file. The installation procedure is given below but not able to understand how to make it. please help

  Read the article

• Manage Internet connection for a program

  - by michel

  I am using a Windows 7 PC with 2 network cards. One for a public line and one for an internal line behind a proxy. Is there a way or a software program where I can manage which program (Outlook, WM) uses which Internet connection or network card? Using the option of interface metric is not what I am looking for. Someone also suggested me ZoneAlarm, but I dislike this program.

  Read the article

• Initial deployment of ClickOnce product on corporate network

  - by MrEdmundo

  Hi there I'm a developer looking at introducing ClickOnce deployment for an internal .NET Winforms application that will be distributed via the corporate network. Currently the product roll out and updates are handled by Group Policy however I would like to control the updates via ClickOnce deployment now. What I would like to know is, how should I initially roll out the package to make sure that all users have got it. Can I use a combination of Group Policy (the roll out) and then rely on the ClickOnce deployment model for any further updates?

  Read the article

• Error while creating a VM using KVM

  - by Karan Gurnani

  I am trying to set up a VM on my Ubuntu 13.04 Desktop and it's giving me error when I try to start the VM. The error states: virsh # start vm1 error: Failed to start domain vm1 error: internal error process exited while connecting to monitor: W: kvm binary is deprecated, please use qemu-system-x86_64 instead char device redirected to /dev/pts/2 (label charserial0) qemu: at most 2047 MB RAM can be simulated What is the workaround for this, if any?

  Read the article

• MD3200 - 3 to 4x less throughput than MD1220. Am I missing something here?

  - by Igor Polishchuk

  I have two R710 servers with similar configuration. One in my office has MD1220 attached. Another one in the datacenter of my hosting services vendor has MD3200. I'm getting significantly worse throughput from MD3200 at my vendors setup. I'm mostly interested in sequential writes, and I'm getting these results in bonnie++ and dd tests: Seq. writes on MD1220 in my office: 1.1 GB/s - bonnie++, 1.3GB/s - dd Seq. writes on MD3200 at my vendor's: 240MB/s - bonnie++, 310MB/s - dd Unfortunately, I could not test the exactly the same configurations, but the two I have should be comparable. If anything, my good performing environment is cheaper than the bad performing. I expect at least similar throughput from these two setups. My vendor cannot really help me. Hopefully, somebody more familiar with the DAS performance can look at it and tell if I'm missing something here and my expectations are too high. To summarize, the question here is it reasonable to expect about 100MB/s of sequential write throughput per each couple of drives in RAID10 on MD3200? Is there any trick to enable such performance in MD3200 with dual controller as opposed to simple MD1220 with a single H800 adapter? More details about the configurations: A good one in my office: Dell R710 2CPU X5650 @ 2.67GHz 12 cores 96GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.26.1.el5 x86_64 20x300GB 2.5" SAS 10K in a single RAID10 1MB chunk size on MD1220 + Dell H800 I/O controller with 1GB cache in the host Not so good one at my vendor's: Dell R710 2CPU L5520 @ 2.27GHz 8 cores 144GB DDR3, OS: RHEL 5.5, kernel 2.6.18-194.11.4.el5 x86_64 20x146GB 2.5" SAS 15K in a single RAID10 512KB chunk size, Dell MD3200, 2 I/O controllers in array with 1GB cache each Additional information. I've also ran the same tests on the same vendor's host, but the storage was: two raids of 14x146GB 15K RPM drives RAID 10, striped together on the OS level on MD3000+MD1000. The performance was about 25% worse than on MD3200 despite having more drives. When I ran similar tests on the internal storage of my vendor's host (2x146GB 15K RPM drives RAID1, Perc 6i) I've got about 128MB/s seq. writes. Just two internal drives gave me about a half of 20 drives' throughput on MD3200. The random I/O performance of the MD3200 setup is ok, it gives me at least 1300 IOPS. I'm mostly have problems with sequentioal I/O throughput. Thank you for looking into it. Regards Igor

  Read the article

• How to install GNU make in Windows 7? [closed]

  - by Azhar

  I am trying to install GNU make-3.82 on Windows 7. I downloaded the make-3.82.tar.gz setup but it does not have any setup file. There is process given on GNU site. But when I reach to the folder in command prompt and after extraction write ./configure it throws error is not recognized as internal or an external command, operable program or batch file. The installation procedure is given below but not able to understand how to make it. please help

  Read the article

• Can I watch DVDs from different regions on a Mac mini using multiple drives?

  - by Christian Berg

  I would like to watch DVDs from two different regions on a Mac mini. Can I do this by connecting an external DVD drive and using the internal drive for one region and the external for the other? Are there additional restrictions in the DVD playing software? If so, how can they be circumvented?

  Read the article

• Compare two NTP servers

  - by David Turner

  Hi, I want to compare the time used by our internal servers against time.microsoft.com. Is there an easy way to do this? Basically a third party sends me messages stamped with a time that has been synced iwth time.microsoft.com, unfortunately our servers are using a different time server, so I want to calculate if there is a significant difference between the our NTP synced time, and theirs. Is there a simple way to accurately compare times? regards, David.

  Read the article

• Linked SQL Server to Oracle

  - by Jerid

  Getting this error when executing SQL Server query only when connected via remote Desktop. When running the query from desktop, no problem. Is this a tsnNames issue? Linked server to Oracle 9i Server: Msg 7399, Level 16, State 1, Line 1 OLE DB provider 'MSDAORA' reported an error. [OLE/DB provider returned message: Unspecified error] [OLE/DB provider returned message: ORA-01041: internal error. hostdef extension doesn't exist ] OLE DB error trace [OLE/DB Provider 'MSDAORA' ICommandText::Execute returned 0x80004005: ].

  Read the article

• Need to setup an office network, suggest some hardware?

  - by Yegor

  We have 6 windows workstations, spread out over a fairly large area. Need to share a DSL connection (upgrading to 100/100 mbit fiber in a few months) with these machines over a 1gbit network. Also need Wifi to be available for laptop use. Plan to add 2 rackmount servers for internal use as well. Can someone suggest a decent (preferably low cost) setup that will let me achieve the stuff mentioned above.

  Read the article

• RDP access to DirectAccess Server via DirectAccess

  - by crgnz

  I have just setup a Win2008R2 DirectAccess server (and also a Win2008R2 Active Directory server). From the Internet I can Remote Desktop login to the AD server, but I cannot RDP into the DirectAccess server. I can PING both servers and get an IPv6 response. (I can RDP to the DirectAccess server from the internal company network) DirectAccess is configured to allow full intranet access. I think I've hit a mental block, the answer will probably be obvious, but I just can't see it.

  Read the article

• Python error after installing libboost-all-dev on debian [migrated]

  - by Cameron Metzke

  A friend of mine wanted the liboost libraries installed on our shared computer so after installing libboost-all-dev 1.49.0.1 ( A debian wheezy machine ), I get this error when using the "pydoc modules" command on the commandline. It spits out the following error -- root@debian:/usr/include/c++/4.7# pydoc modules Please wait a moment while I gather a list of all available modules... **[debian:49065] [[INVALID],INVALID] ORTE_ERROR_LOG: A system-required executable either could not be found or was not executable by this user in file ../../../../../../orte/mca/ess/singleton/ess_singleton_module.c at line 357 [debian:49065] [[INVALID],INVALID] ORTE_ERROR_LOG: A system-required executable either could not be found or was not executable by this user in file ../../../../../../orte/mca/ess/singleton/ess_singleton_module.c at line 230 [debian:49065] [[INVALID],INVALID] ORTE_ERROR_LOG: A system-required executable either could not be found or was not executable by this user in file ../../../orte/runtime/orte_init.c at line 132 -------------------------------------------------------------------------- It looks like orte_init failed for some reason; your parallel process is likely to abort. There are many reasons that a parallel process can fail during orte_init; some of which are due to configuration or environment problems. This failure appears to be an internal failure; here's some additional information (which may only be relevant to an Open MPI developer): orte_ess_set_name failed --> Returned value A system-required executable either could not be found or was not executable by this user (-127) instead of ORTE_SUCCESS -------------------------------------------------------------------------- -------------------------------------------------------------------------- It looks like MPI_INIT failed for some reason; your parallel process is likely to abort. There are many reasons that a parallel process can fail during MPI_INIT; some of which are due to configuration or environment problems. This failure appears to be an internal failure; here's some additional information (which may only be relevant to an Open MPI developer): ompi_mpi_init: orte_init failed --> Returned "A system-required executable either could not be found or was not executable by this user" (-127) instead of "Success" (0) -------------------------------------------------------------------------- *** The MPI_Init() function was called before MPI_INIT was invoked. *** This is disallowed by the MPI standard. *** Your MPI job will now abort. [debian:49065] Abort before MPI_INIT completed successfully; not able to guarantee that all other processes were killed!** root@debian:/usr/include/c++/4.7# I tried looking into the problem and ended up uninstalling the following to get it to work again. openmpi common all 1.4.5-1 libibverbs-dev amd64 1.1.6-1 libopenmpi-dev amd64 1.4.5-1 mpi-default-dev amd64 1.0.1 libboost-mpi-python1.49.0 although pydoc works again, I'm assuming the packages I removed are gunna hurt somethiong else down the track ? As you guessed im not a c/c++ programmer. So I guess my question is, will this hurt something later ? is their a way to install those packages without hurting python ?

  Read the article

• Trailing dots in url result in empty 404 page on IIS

  - by Peter Hahndorf

  I have an ASP.NET site on IIS8, but IIS7.5 behaves exactly the same. When I enter a URL like: mysite.com/foo/bar.. I get the following error with a '500 Internal Server Error' status code: even though I have custom error pages set up for 500 and 404 and I don't see anything wrong with my custom error page. In my web.config system.web node I have the following: <customErrors mode="On"> <error statusCode="404" redirect="/404.aspx" /> </customErrors> If I remove that section, I get a 404.0 response back but the page itself is blank. In web.config system.webServer I have: <httpErrors errorMode="DetailedLocalOnly"> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="404.html" responseMode="File" /> </httpErrors> But whether that is there or not, I get the same blank 404.0 page rather than my expected custom error page, or at least an internal IIS message. So first of all why is the asp.net handler picking up a request for '..' (also works with one or more trailing dots) If I remove the following handler from applicacationHost.config: <add name="ExtensionlessUrlHandler-Integrated-4.0" path="*." verb="GET,HEAD,POST,DEBUG" type="System.Web.Handlers.TransferRequestHandler" preCondition="integratedMode,runtimeVersionv4.0" responseBufferLimit="0" /> I get my expected custom 404 page, but of course removing that handler breaks routing in asp.net among other things. Looking at the failure trace I see: Windows Authentication is disabled for the site, so why is that module even in the request pipeline? For now my fix is to use the URL Rewrite module with the following rule: <rewrite> <rules> <rule name="Trailing Dots" stopProcessing="true"> <match url="\.+$" /> <action type="Rewrite" url="/404.html" appendQueryString="false" /> </rule> </rules> </rewrite> This works okay, but I wonder why IIS/ASP.NET behaves this way?

  Read the article

• OWA, Outlook Anywhere, RPCPing Inconsistencies

  - by pk.

  I'm troubleshooting an Outlook Anywhere issue with a new Exchange 2010 server. The server in question, MS2010, is behind a SonicWALL NSA 2400 device and works wonderfully except for Outlook Anywhere. Outlook Anywhere works internally and I've verified (through Ctrl-Right Click --> Connection Status) that I'm able to connect to MS2010 over HTTPS. When trying to connect to the server using HTTPS from outside the firewall, I'm unable to do so. A Wireshark trace shows 30 or so successful HTTPS packet transmissions, and then it fails with 3 straight transmissions to a destination port of 135. I have no idea why my computer is attempting to access anything on port 135 since I've setup my profile to use HTTPS on both slow and fast connections. I'm 99% certain that the firewall is configured correctly. I run Outlook Web Access (also HTTPS) on the same server and there are no issues with access. EDIT: My Autodiscover settings are correct (as far as I can tell). My server passes the Outlook Anywhere and Autodiscover tests at https://www.testexchangeconnectivity.com/. I've been using the RPCPing utility to troubleshoot and have come across the following results: Internally- >rpcping -t ncacn_http -s mail.mydomain.com -o RpcProxy=mail.mydomain.com -P "pk,mydomain,*" -I "pk,mydomain,*" -H 1 -u 10 -a connect -F 3 -v 3 -E -R none RPCPing v2.12. Copyright (C) Microsoft Corporation, 2002 OS Version is: 6.1, Service Pack 1 RPCPinging proxy server mail.mydomain.com with Echo Request Packet Sending ping to server Response from server received: 200 Pinging successfully completed in 93 ms Externally- >rpcping -t ncacn_http -s mail.mydomain.com -o RpcProxy=mail.mydomain.com -P "pk,mydomain,*" -I "pk,mydomain,*" -H 1 -u 10 -a connect -F 3 -v 3 -E -R none RPCPing v6.0. Copyright (C) Microsoft Corporation, 2002-2006 Enter password for RPC/HTTP proxy: RPCPing set Activity ID: {fc8411ba-2987-4175-b37b-801dc69d5ff9} RPCPinging proxy server mail.mydomain.com with Echo Request Packet Setting autologon policy to high WinHttpSetCredentials for target server called Error 87 : The parameter is incorrect. returned in WinHttpSetCredentials Ping failed What should I be checking in order to troubleshoot my Outlook Anywhere issues? I'm using Windows 7 SP1 for internal and external access. EDIT: Autodiscover.xml content <?xml version="1.0"?> <Autodiscover xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns="http://schemas.microsoft.com/exchange/autodiscover/responseschema/2006"> <Response xmlns="http://schemas.microsoft.com/exchange/autodiscover/outlook/responseschema/2006a"> <User> <DisplayName>John Doe</DisplayName> <LegacyDN>/o=MYDOMAIN/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Recipients/cn=pk</LegacyDN> <DeploymentId>d35170cc-f3a7-42c5-9427-1f554a469126</DeploymentId> </User> <Account> <AccountType>email</AccountType> <Action>settings</Action> <Protocol> <Type>EXCH</Type> <Server>MS2010.MYDOMAIN.local</Server> <ServerDN>/o=MYDOMAIN/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Configuration/cn=Servers/cn=MS2010</ServerDN> <ServerVersion>738180DA</ServerVersion> <MdbDN>/o=MYDOMAIN/ou=Exchange Administrative Group (FYDIBOHF23SPDLT)/cn=Configuration/cn=Servers/cn=MS2010/cn=Microsoft Private MDB</MdbDN> <ASUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</ASUrl> <OOFUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</OOFUrl> <OABUrl>http://MS2010.MYDOMAIN.local/OAB/2c34c9f5-5521-4c8c-b684-538df815052a/</OABUrl> <UMUrl>https://MS2010.MYDOMAIN.local/EWS/UM2007Legacy.asmx</UMUrl> <Port>0</Port> <DirectoryPort>0</DirectoryPort> <ReferralPort>0</ReferralPort> <PublicFolderServer>MS2007.MYDOMAIN.local</PublicFolderServer> <AD>dc1.MYDOMAIN.local</AD> <EwsUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</EwsUrl> <EcpUrl>https://MS2010.MYDOMAIN.local/ecp/</EcpUrl> <EcpUrl-um>?p=customize/voicemail.aspx&amp;exsvurl=1</EcpUrl-um> <EcpUrl-aggr>?p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1</EcpUrl-aggr> <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;</EcpUrl-mt> <EcpUrl-ret>?p=organize/retentionpolicytags.slab&amp;exsvurl=1</EcpUrl-ret> <EcpUrl-sms>?p=sms/textmessaging.slab&amp;exsvurl=1</EcpUrl-sms> </Protocol> <Protocol> <Type>EXPR</Type> <Server>mail.mycompany.com</Server> <ASUrl>https://mail.mycompany.com/ews/exchange.asmx</ASUrl> <OOFUrl>https://mail.mycompany.com/ews/exchange.asmx</OOFUrl> <OABUrl>https://mail.mycompany.com/OAB/2c34c9f5-5521-4c8c-b684-538df815052a/</OABUrl> <UMUrl>https://mail.mycompany.com/ews/UM2007Legacy.asmx</UMUrl> <Port>0</Port> <DirectoryPort>0</DirectoryPort> <ReferralPort>0</ReferralPort> <SSL>On</SSL> <AuthPackage>Basic</AuthPackage> <CertPrincipalName>msstd:mail.mycompany.com</CertPrincipalName> <EwsUrl>https://mail.mycompany.com/ews/exchange.asmx</EwsUrl> <EcpUrl>https://mail.mycompany.com/owa/</EcpUrl> <EcpUrl-um>?p=customize/voicemail.aspx&amp;exsvurl=1</EcpUrl-um> <EcpUrl-aggr>?p=personalsettings/EmailSubscriptions.slab&amp;exsvurl=1</EcpUrl-aggr> <EcpUrl-mt>PersonalSettings/DeliveryReport.aspx?exsvurl=1&amp;IsOWA=&lt;IsOWA&gt;&amp;MsgID=&lt;MsgID&gt;&amp;Mbx=&lt;Mbx&gt;</EcpUrl-mt> <EcpUrl-ret>?p=organize/retentionpolicytags.slab&amp;exsvurl=1</EcpUrl-ret> <EcpUrl-sms>?p=sms/textmessaging.slab&amp;exsvurl=1</EcpUrl-sms> </Protocol> <Protocol> <Type>WEB</Type> <Port>0</Port> <DirectoryPort>0</DirectoryPort> <ReferralPort>0</ReferralPort> <Internal> <OWAUrl AuthenticationMethod="Basic, Fba">https://MS2010.MYDOMAIN.local/owa/</OWAUrl> <Protocol> <Type>EXCH</Type> <ASUrl>https://MS2010.MYDOMAIN.local/EWS/Exchange.asmx</ASUrl> </Protocol> </Internal> <External> <OWAUrl AuthenticationMethod="Fba">https://mail.mycompany.com/owa/</OWAUrl> <Protocol> <Type>EXPR</Type> <ASUrl>https://mail.mycompany.com/ews/exchange.asmx</ASUrl> </Protocol> </External> </Protocol> </Account> </Response> </Autodiscover>

  Read the article

• How to block outside network access on a windows 2008 server

  - by David

  I setup a windows 2008 server for some internal stuff (file sharing, sql server, etc). I only need to access the machine from computers that are inside the network. What is the best/easiest way to block all outgoing and incoming traffic on the server?

  Read the article

• Puppet's automatically generated certificates failing

  - by gparent

  I am running a default configuration of Puppet on Debian Squeeze 6.0.4. The server's FQDN is master.example.com. The client's FQDN is client.example.com. I am able to contact the puppet master and send a CSR. I sign it using puppetca -sa but the client will still not connect. Date of both machines is within 2 seconds of Tue Apr 3 20:59:00 UTC 2012 as I wrote this sentence. This is what appears in /var/log/syslog: Apr 3 17:03:52 localhost puppet-agent[18653]: Reopening log files Apr 3 17:03:52 localhost puppet-agent[18653]: Starting Puppet client version 2.6.2 Apr 3 17:03:53 localhost puppet-agent[18653]: Could not retrieve catalog from remote server: SSL_connect returned=1 errno=0 state=SSLv3 read server certificate B: certificate verify failed Apr 3 17:03:53 localhost puppet-agent[18653]: Using cached catalog Apr 3 17:03:53 localhost puppet-agent[18653]: Could not retrieve catalog; skipping run Here is some interesting output: OpenSSL client test: client:~# openssl s_client -host master.example.com -port 8140 -cert /var/lib/puppet/ssl/certs/client.example.com.pem -key /var/lib/puppet/ssl/private_keys/client.example.com.pem -CAfile /var/lib/puppet/ssl/certs/ca.pem CONNECTED(00000003) depth=1 /CN=Puppet CA: master.example.com verify return:1 depth=0 /CN=master.example.com verify error:num=7:certificate signature failure verify return:1 depth=0 /CN=master.example.com verify return:1 18509:error:1409441B:SSL routines:SSL3_READ_BYTES:tlsv1 alert decrypt error:s3_pkt.c:1102:SSL alert number 51 18509:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:188: client:~# master's certificate: root@master:/etc/puppet# openssl x509 -text -noout -in /etc/puppet/ssl/certs/master.example.com.pem Certificate: Data: Version: 3 (0x2) Serial Number: 2 (0x2) Signature Algorithm: sha1WithRSAEncryption Issuer: CN=Puppet CA: master.example.com Validity Not Before: Apr 2 20:01:28 2012 GMT Not After : Apr 2 20:01:28 2017 GMT Subject: CN=master.example.com Subject Public Key Info: Public Key Algorithm: rsaEncryption RSA Public Key: (1024 bit) Modulus (1024 bit): 00:a9:c1:f9:4c:cd:0f:68:84:7b:f4:93:16:20:44: 7a:2b:05:8e:57:31:05:8e:9c:c8:08:68:73:71:39: c1:86:6a:59:93:6e:53:aa:43:11:83:5b:2d:8c:7d: 54:05:65:c1:e1:0e:94:4a:f0:86:58:c3:3d:4f:f3: 7d:bd:8e:29:58:a6:36:f4:3e:b2:61:ec:53:b5:38: 8e:84:ac:5f:a3:e3:8c:39:bd:cf:4f:3c:ff:a9:65: 09:66:3c:ba:10:14:69:d5:07:57:06:28:02:37:be: 03:82:fb:90:8b:7d:b3:a5:33:7b:9b:3a:42:51:12: b3:ac:dd:d5:58:69:a9:8a:ed Exponent: 65537 (0x10001) X509v3 extensions: X509v3 Basic Constraints: critical CA:FALSE Netscape Comment: Puppet Ruby/OpenSSL Internal Certificate X509v3 Key Usage: critical Digital Signature, Key Encipherment X509v3 Subject Key Identifier: 8C:2F:14:84:B6:A1:B5:0C:11:52:36:AB:E5:3F:F2:B9:B3:25:F3:1C X509v3 Extended Key Usage: critical TLS Web Server Authentication, TLS Web Client Authentication Signature Algorithm: sha1WithRSAEncryption 7b:2c:4f:c2:76:38:ab:03:7f:c6:54:d9:78:1d:ab:6c:45:ab: 47:02:c7:fd:45:4e:ab:b5:b6:d9:a7:df:44:72:55:0c:a5:d0: 86:58:14:ae:5f:6f:ea:87:4d:78:e4:39:4d:20:7e:3d:6d:e9: e2:5e:d7:c9:3c:27:43:a4:29:44:85:a1:63:df:2f:55:a9:6a: 72:46:d8:fb:c7:cc:ca:43:e7:e1:2c:fe:55:2a:0d:17:76:d4: e5:49:8b:85:9f:fa:0e:f6:cc:e8:28:3e:8b:47:b0:e1:02:f0: 3d:73:3e:99:65:3b:91:32:c5:ce:e4:86:21:b2:e0:b4:15:b5: 22:63 root@master:/etc/puppet# CA's certificate: root@master:/etc/puppet# openssl x509 -text -noout -in /etc/puppet/ssl/certs/ca.pem Certificate: Data: Version: 3 (0x2) Serial Number: 1 (0x1) Signature Algorithm: sha1WithRSAEncryption Issuer: CN=Puppet CA: master.example.com Validity Not Before: Apr 2 20:01:05 2012 GMT Not After : Apr 2 20:01:05 2017 GMT Subject: CN=Puppet CA: master.example.com Subject Public Key Info: Public Key Algorithm: rsaEncryption RSA Public Key: (1024 bit) Modulus (1024 bit): 00:b5:2c:3e:26:a3:ae:43:b8:ed:1e:ef:4d:a1:1e: 82:77:78:c2:98:3f:e2:e0:05:57:f0:8d:80:09:36: 62:be:6c:1a:21:43:59:1d:e9:b9:4d:e0:9c:fa:09: aa:12:a1:82:58:fc:47:31:ed:ad:ad:73:01:26:97: ef:d2:d6:41:6b:85:3b:af:70:00:b9:63:e9:1b:c3: ce:57:6d:95:0e:a6:d2:64:bd:1f:2c:1f:5c:26:8e: 02:fd:d3:28:9e:e9:8f:bc:46:bb:dd:25:db:39:57: 81:ed:e5:c8:1f:3d:ca:39:cf:e7:f3:63:75:f6:15: 1f:d4:71:56:ed:84:50:fb:5d Exponent: 65537 (0x10001) X509v3 extensions: X509v3 Basic Constraints: critical CA:TRUE Netscape Comment: Puppet Ruby/OpenSSL Internal Certificate X509v3 Key Usage: critical Certificate Sign, CRL Sign X509v3 Subject Key Identifier: 8C:2F:14:84:B6:A1:B5:0C:11:52:36:AB:E5:3F:F2:B9:B3:25:F3:1C Signature Algorithm: sha1WithRSAEncryption 1d:cd:c6:65:32:42:a5:01:62:46:87:10:da:74:7e:8b:c8:c9: 86:32:9e:c2:2e:c1:fd:00:79:f0:ef:d8:73:dd:7e:1b:1a:3f: cc:64:da:a3:38:ad:49:4e:c8:4d:e3:09:ba:bc:66:f2:6f:63: 9a:48:19:2d:27:5b:1d:2a:69:bf:4f:f4:e0:67:5e:66:84:30: e5:85:f4:49:6e:d0:92:ae:66:77:50:cf:45:c0:29:b2:64:87: 12:09:d3:10:4d:91:b6:f3:63:c4:26:b3:fa:94:2b:96:18:1f: 9b:a9:53:74:de:9c:73:a4:3a:8d:bf:fa:9c:c0:42:9d:78:49: 4d:70 root@master:/etc/puppet# Client's certificate: client:~# openssl x509 -text -noout -in /var/lib/puppet/ssl/certs/client.example.com.pem Certificate: Data: Version: 3 (0x2) Serial Number: 3 (0x3) Signature Algorithm: sha1WithRSAEncryption Issuer: CN=Puppet CA: master.example.com Validity Not Before: Apr 2 20:01:36 2012 GMT Not After : Apr 2 20:01:36 2017 GMT Subject: CN=client.example.com Subject Public Key Info: Public Key Algorithm: rsaEncryption RSA Public Key: (1024 bit) Modulus (1024 bit): 00:ae:88:6d:9b:e3:b1:fc:47:07:d6:bf:ea:53:d1: 14:14:9b:35:e6:70:43:e0:58:35:76:ac:c5:9d:86: 02:fd:77:28:fc:93:34:65:9d:dd:0b:ea:21:14:4d: 8a:95:2e:28:c9:a5:8d:a2:2c:0e:1c:a0:4c:fa:03: e5:aa:d3:97:98:05:59:3c:82:a9:7c:0e:e9:df:fd: 48:81:dc:33:dc:88:e9:09:e4:19:d6:e4:7b:92:33: 31:73:e4:f2:9c:42:75:b2:e1:9f:d9:49:8c:a7:eb: fa:7d:cb:62:22:90:1c:37:3a:40:95:a7:a0:3b:ad: 8e:12:7c:6e:ad:04:94:ed:47 Exponent: 65537 (0x10001) X509v3 extensions: X509v3 Basic Constraints: critical CA:FALSE Netscape Comment: Puppet Ruby/OpenSSL Internal Certificate X509v3 Key Usage: critical Digital Signature, Key Encipherment X509v3 Subject Key Identifier: 8C:2F:14:84:B6:A1:B5:0C:11:52:36:AB:E5:3F:F2:B9:B3:25:F3:1C X509v3 Extended Key Usage: critical TLS Web Server Authentication, TLS Web Client Authentication Signature Algorithm: sha1WithRSAEncryption 33:1f:ec:3c:91:5a:eb:c6:03:5f:a1:58:60:c3:41:ed:1f:fe: cb:b2:40:11:63:4d:ba:18:8a:8b:62:ba:ab:61:f5:a0:6c:0e: 8a:20:56:7b:10:a1:f9:1d:51:49:af:70:3a:05:f9:27:4a:25: d4:e6:88:26:f7:26:e0:20:30:2a:20:1d:c4:d3:26:f1:99:cf: 47:2e:73:90:bd:9c:88:bf:67:9e:dd:7c:0e:3a:86:6b:0b:8d: 39:0f:db:66:c0:b6:20:c3:34:84:0e:d8:3b:fc:1c:a8:6c:6c: b1:19:76:65:e6:22:3c:bf:ff:1c:74:bb:62:a0:46:02:95:fa: 83:41 client:~#

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >