Search Results

Search found 22500 results on 900 pages for 'memory issues'.

Page 90/900 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• Apache with mod_php high memory utilization

  - by Raj

  We have Magento application deployed on Apache with mod_php and mysql. I have observed that sometime apache server starts consuming high memory which causes memory swapping and results in high load on servers. whenever there is high load on apache server, the apache processes which are causing the high load were in sleep mode at mysql end and CLOSE_WAIT state at client side. Any help is appreciated to resolve this issue.

  Read the article

• Windows 7 booting and startup repair issues

  - by aardvark

  I have a MSI FR720 laptop with Windows 7 and Lubuntu partions. For quite a while (6 months or so) I've been having issues booting from my hard drive, it'd take me between 5 minutes and several hours for me to be able to have it recognize the hard drive as a bootable device. I did several disk checks on it, and my hard drive seems in perfect condition, and the fact that booting would usually only work after removing the hard drive and trying to reset it in its slot or lightly shaking it makes me think it had something to do with the connection in the hard drive slot as opposed to the hard drive itself. I was having particular issues with it detecting the hard drive today so I decided to try booting it from an external hard drive dock. It detected it first try and so far has had no problems finding the bootable partitions on my hard drive. When I selected my Windows 7 partition from the boot menu it said that it hadn't been shut down properly last time and needed startup repair. I've done this several times over the last 6 months, so this is hardly unusual. I do startup repair, it fails, and then I try to do a system restore. The system restore also failed, and it says that no files were changed. I restart and try it again. However, this time when I get to the startup repair it's not detecting a Windows OS. I tried clicking next and doing a startup repair but the repair is always failing. If I ignore the startup repair option and instead select "Launch windows normally" it will get to the windows animation, stop halfway through and then crash into a BSoD. I can't read the error on the screen because it immediately switches to back and tries to restart. This is my first time asking a question like this online, so let me know if I need to provide any extra information and I'll do my best to give it I tried using diskpart to find the list of partitions and see if one's labelled as an active partition, but it says that no disk were detected. I can run Lubuntu just fine. I can also see all of my Windows 7 files from it EDIT: The startup repair diagnosis and repair log is this: -- Number of repair attempts: 1 Session details System Disk = Windows directory = AutoChk Run = 0 Number of root causes = 1 Test Performed: Name: Check for updates Result: Completed successfully. Error code = 0x0 Time taken = 15ms Test Performed: Name: System disk test Result: Completed successfully. Error code = 0x0 Time taken = 31ms Root cause found. If a hard disk is installed, it is not responding. -- Any chance that this is a result of me doing this through an external dock through a USB drive?

  Read the article

• Techniques to find out USB 2.0 power issues

  - by iceman

  I have a Dell Precision T3400 on Windows Xp Pro Sp3 and whenever i connect an external Hard drive, it dies after a few seconds. However the drive works fine in other computers. How can I debug USB power issues?

  Read the article

• gvfsd takes up too much memory

  - by Tim

  Hi, On my Ubuntu 8.10, gvfsd takes up 128.6MB memory. What is the process doing actually? Can I reduce the memory it takes? Thanks and regards!

  Read the article

• Windows XP maximum memory - reduced by graphics card memory?

  - by John C

  I've seen occasional references that claimed a graphics card's video memory was part of Windows XP's memory address space - is that true? If you have 4GB on an XP system, and add a 1GB graphics card, does that mean Windows only has 3GB for programs?

  Read the article

• Oracle présente sa solution « in-memory » pour concurrencer SAP et Microsoft, l'option sera disponible avec Oracle Database 12c dans un mois

  Oracle présente sa solution « in-memory » pour concurrencer SAP et Microsoft l'option sera disponible avec Oracle Database 12c dans un moisDans le secteur des bases de données, la tendance est à la course aux performances avec la nouvelle option « in-Memory », un concept qui consiste à mettre en cache les données traitées par les applications plutôt que, par exemple, de faire des appels à un serveur.SAP a été le pionnier des solutions in-memory avec sa solution « SAP in-memory » incluse dans la...

  Read the article

• The amount of memory used by each process

  - by tuxsmouf

  I have a mysql server running debian with 2GO of RAM. I would like to know the amount of memory used by each process. I thought ps -aux was the command and options for it. But I only see 90 MO used by several processes and free -m tells me that 1400 MO are used. Is there a way to have a better view with the processes and the memory used by them ?

  Read the article

• Using ServletOutputStream to write very large files in a Java servlet without memory issues

  - by Martin

  I am using IBM Websphere Application Server v6 and Java 1.4 and am trying to write large CSV files to the ServletOutputStream for a user to download. Files are ranging from a 50-750MB at the moment. The smaller files aren't causing too much of a problem but with the larger files it appears that it is being written into the heap which is then causing an OutOfMemory error and bringing down the entire server. These files can only be served out to authenticated users over https which is why I am serving them through a Servlet instead of just sticking them in Apache. The code I am using is (some fluff removed around this): resp.setHeader("Content-length", "" + fileLength); resp.setContentType("application/vnd.ms-excel"); resp.setHeader("Content-Disposition","attachment; filename=\"export.csv\""); FileInputStream inputStream = null; try { inputStream = new FileInputStream(path); byte[] buffer = new byte[1024]; int bytesRead = 0; do { bytesRead = inputStream.read(buffer, offset, buffer.length); resp.getOutputStream().write(buffer, 0, bytesRead); } while (bytesRead == buffer.length); resp.getOutputStream().flush(); } finally { if(inputStream != null) inputStream.close(); } The FileInputStream doesn't seem to be causing a problem as if I write to another file or just remove the write completly the memory usage doesn't appear to be a problem. What I am thinking is that the resp.getOutputStream().write is being stored in memory until the data can be sent through to the client. So the entire file might be read and stored in the resp.getOutputStream() causing my memory issues and crashing! I have tried Buffering these streams and also tried using Channels from java.nio, none of which seems to make any bit of difference to my memory issues. I have also flushed the outputstream once per iteration of the loop and after the loop, which didn't help.

  Read the article

• Hard crash when drawing content for CALayer using quartz

  - by Lukasz

  I am trying to figure out why iOS crash my application in the harsh way (no crash logs, immediate shudown with black screen of death with spinner shown for a while). It happens when I render content for CALayer using Quartz. I suspected the memory issue (happens only when testing on the device), but memory logs, as well as instruments allocation logs looks quite OK. Let me past in the fatal function: - (void)renderTiles{ if (rendering) { //NSLog(@"====== RENDERING TILES SKIP ======="); return; } rendering = YES; CGRect b = tileLayer.bounds; CGSize s = b.size; CGFloat imageScale = [[UIScreen mainScreen] scale]; s.height *= imageScale; s.width *= imageScale; dispatch_async(queue, ^{ NSLog(@""); NSLog(@"====== RENDERING TILES START ======="); NSLog(@"1. Before creating context"); report_memory(); CGColorSpaceRef colorSpace = CGColorSpaceCreateDeviceRGB(); NSLog(@"2. After creating color space"); report_memory(); NSLog(@"3. About to create context with size: %@", NSStringFromCGSize(s)); CGContextRef ctx = CGBitmapContextCreate(NULL, s.width, s.height, 8, 0, colorSpace, kCGImageAlphaPremultipliedLast); NSLog(@"4. After creating context"); report_memory(); CGAffineTransform flipTransform = CGAffineTransformMake(1.0, 0.0, 0.0, -1.0, 0.0, s.height); CGContextConcatCTM(ctx, flipTransform); CGRect tileRect = CGRectMake(0, 0, tileImageScaledSize.width, tileImageScaledSize.height); CGContextDrawTiledImage(ctx, tileRect, tileCGImageScaled); NSLog(@"5. Before creating cgimage from context"); report_memory(); CGImageRef cgImage = CGBitmapContextCreateImage(ctx); NSLog(@"6. After creating cgimage from context"); report_memory(); dispatch_sync(dispatch_get_main_queue(), ^{ tileLayer.contents = (id)cgImage; }); NSLog(@"7. After asgning tile layer contents = cgimage"); report_memory(); CGColorSpaceRelease(colorSpace); CGContextRelease(ctx); CGImageRelease(cgImage); NSLog(@"8. After releasing image and context context"); report_memory(); NSLog(@"====== RENDERING TILES END ======="); NSLog(@""); rendering = NO; }); } Here are the logs: ====== RENDERING TILES START ======= 1. Before creating context Memory in use (in bytes): 28340224 / 519442432 (5.5%) 2. After creating color space Memory in use (in bytes): 28340224 / 519442432 (5.5%) 3. About to create context with size: {6324, 5208} 4. After creating context Memory in use (in bytes): 28344320 / 651268096 (4.4%) 5. Before creating cgimage from context Memory in use (in bytes): 153649152 / 651333632 (23.6%) 6. After creating cgimage from context Memory in use (in bytes): 153649152 / 783159296 (19.6%) 7. After asgning tile layer contents = cgimage Memory in use (in bytes): 153653248 / 783253504 (19.6%) 8. After releasing image and context context Memory in use (in bytes): 21688320 / 651288576 (3.3%) ====== RENDERING TILES END ======= Application crashes in random places. Sometimes when reaching en of the function and sometime in random step. Which direction should I look for a solution? Is is possible that GDC is causing the problem? Or maybe the context size or some Core Animation underlying references?

  Read the article

• How do i mount my SD Card? I am using ubuntu 10.04

  - by shobhit

  root@shobhit:/media# lsusb Bus 002 Device 017: ID 14cd:125c Super Top Bus 002 Device 003: ID 0c45:6421 Microdia Bus 002 Device 002: ID 8087:0020 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 011: ID 413c:8160 Dell Computer Corp. Bus 001 Device 006: ID 413c:8162 Dell Computer Corp. Bus 001 Device 005: ID 413c:8161 Dell Computer Corp. Bus 001 Device 004: ID 138a:0008 DigitalPersona, Inc Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 001 Device 002: ID 8087:0020 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lspci -v -nn 00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fbc08000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at fbc07000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a6) (prog-if 01) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=20, subordinate=20, sec-latency=32 Capabilities: [50] Subsystem: Dell Device [1028:0441] 00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b0b] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b2f] (rev 06) (prog-if 01) Subsystem: Dell Device [1028:0441] Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 29 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at fbc06000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 06) Subsystem: Dell Device [1028:0441] Flags: medium devsel, IRQ 3 Memory at fbc05000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem [8086:3b32] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 3 Memory at fbc04000 (64-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 3 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 12:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4727] (rev 01) Subsystem: Dell Device [1028:0010] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number cb-c0-8b-ff-ff-38-00-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl 13:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 28 I/O ports at e000 [size=256] Memory at d0b04000 (64-bit, prefetchable) [size=4K] Memory at d0b00000 (64-bit, prefetchable) [size=16K] Expansion ROM at fba00000 [disabled] [size=128K] Capabilities: [40] Power Management version 3 Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4 Capabilities: [cc] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-03 Kernel driver in use: r8169 Kernel modules: r8169 root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lshw shobhit description: Portable Computer product: Vostro 3500 vendor: Dell Inc. version: A10 serial: FV1L3N1 width: 32 bits capabilities: smbios-2.6 dmi-2.6 smp-1.4 smp configuration: boot=normal chassis=portable cpus=2 uuid=44454C4C-5600-1031-804C-C6C04F334E31 *-core description: Motherboard product: 0G2R51 vendor: Dell Inc. physical id: 0 version: A10 serial: .FV1L3N1.CN7016612H00PW. slot: To Be Filled By O.E.M. *-cpu:0 description: CPU product: Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 slot: CPU 1 size: 1197MHz capacity: 2926MHz width: 64 bits clock: 533MHz capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp x86-64 constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida arat tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: id=4 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 3MiB capacity: 3MiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 4.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 width: 64 bits capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 width: 64 bits capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 width: 64 bits capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 width: 64 bits capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 width: 64 bits capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 width: 64 bits capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a width: 64 bits capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b width: 64 bits capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c width: 64 bits capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d width: 64 bits capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e width: 64 bits capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f width: 64 bits capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 3GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT112S6TFR8C-H9 vendor: AD80 physical id: 0 serial: 5525C935 slot: DIMM_A size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT125S6TFR8C-H9 vendor: AD80 physical id: 1 serial: 3441D6CA slot: DIMM_B size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A10 (10/25/2010) size: 64KiB capacity: 1984KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 size: 1197MHz capacity: 1197MHz capabilities: vmx ht cpufreq configuration: id=4 *-logicalcpu:0 description: Logical CPU physical id: 4.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 capabilities: logical *-pci description: Host bridge product: Core Processor DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 18 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 18 width: 64 bits clock: 33MHz capabilities: msi pm bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:30 memory:fac00000-faffffff memory:c0000000-cfffffff(prefetchable) ioport:f080(size=8) *-communication UNCLAIMED description: Communication controller product: 5 Series/3400 Series Chipset HECI Controller vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc09000-fbc0900f *-usb:0 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fbc08000-fbc083ff *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:22 memory:fbc00000-fbc03fff *-pci:0 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:24 ioport:2000(size=4096) memory:bc000000-bc1fffff memory:bc200000-bc3fffff(prefetchable) *-pci:1 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:25 ioport:3000(size=4096) memory:fbb00000-fbbfffff memory:bc400000-bc5fffff(prefetchable) *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:8b:aa:d8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=10.0.1.50 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbb00000-fbb03fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 3 vendor: Intel Corporation physical id: 1c.2 bus info: pci@0000:00:1c.2 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:26 ioport:e000(size=4096) memory:fba00000-fbafffff ioport:d0b00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 03 serial: 78:2b:cb:cc:0e:2a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:28 ioport:e000(size=256) memory:d0b04000-d0b04fff(prefetchable) memory:d0b00000-d0b03fff(prefetchable) memory:fba00000-fba1ffff(prefetchable) *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:27 ioport:d000(size=4096) memory:fb000000-fb9fffff ioport:d0000000(size=10485760) *-usb:1 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fbc07000-fbc073ff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a6 width: 32 bits clock: 33MHz capabilities: pci bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 06 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 5 Series/3400 Series Chipset 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi1 version: 06 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:29 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fbc06000-fbc067ff *-disk description: ATA Disk product: WDC WD3200BEKT-7 vendor: Western Digital physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WX21AC0W1945 size: 298GiB (320GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=77e3ed41 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: aa69-51c0 size: 98MiB capacity: 100MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-04-03 02:00:15 filesystem=ntfs label=System Reserved state=clean *-volume:1 description: Windows NTFS volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 3.1 serial: 9854ff5c-1dea-a147-84a6-624e758f44b8 size: 48GiB capacity: 48GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-10 13:55:31 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:2 description: Extended partition physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 size: 48GiB capacity: 48GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 1952MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 46GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,barrier=1,data=ordered state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/56AA8094AA807273 version: 3.1 serial: 22a29e8d-56c7-9a4a-adea-528103948f6d size: 200GiB capacity: 200GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-02 20:17:15 filesystem=ntfs modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-cdrom description: DVD-RAM writer product: DVD+-RW TS-L633J vendor: TSSTcorp physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 version: D200 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 06 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fbc05000-fbc050ff ioport:f000(size=32) *-generic UNCLAIMED description: Signal processing controller product: 5 Series/3400 Series Chipset Thermal Subsystem vendor: Intel Corporation physical id: 1f.6 bus info: pci@0000:00:1f.6 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc04000-fbc04fff *-scsi physical id: 2 bus info: usb@2:1.1 logical name: scsi15 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@15:0.0.0 logical name: /dev/sdb I have tried all options like fdisk /dev/sdb , pmount /dev/sdb but nothing is working .Pls guide me

  Read the article

• How'd they do it: Millions of tiles in Terraria

  - by William 'MindWorX' Mariager

  I've been working up a game engine similar to Terraria, mostly as a challenge, and while I've figured out most of it, I can't really seem to wrap my head around how they handle the millions of interactable/harvestable tiles the game has at one time. Creating around 500.000 tiles, that is 1/20th of what's possible in Terraria, in my engine causes the frame-rate to drop from 60 to around 20, even tho I'm still only rendering the tiles in view. Mind you, I'm not doing anything with the tiles, only keeping them in memory. Update: Code added to show how I do things. This is part of a class, which handles the tiles and draws them. I'm guessing the culprit is the "foreach" part, which iterates everything, even empty indexes. ... public void Draw(SpriteBatch spriteBatch, GameTime gameTime) { foreach (Tile tile in this.Tiles) { if (tile != null) { if (tile.Position.X < -this.Offset.X + 32) continue; if (tile.Position.X > -this.Offset.X + 1024 - 48) continue; if (tile.Position.Y < -this.Offset.Y + 32) continue; if (tile.Position.Y > -this.Offset.Y + 768 - 48) continue; tile.Draw(spriteBatch, gameTime); } } } ... Also here is the Tile.Draw method, which could also do with an update, as each Tile uses four calls to the SpriteBatch.Draw method. This is part of my autotiling system, which means drawing each corner depending on neighboring tiles. texture_* are Rectangles, are set once at level creation, not each update. ... public virtual void Draw(SpriteBatch spriteBatch, GameTime gameTime) { if (this.type == TileType.TileSet) { spriteBatch.Draw(this.texture, this.realm.Offset + this.Position, texture_tl, this.BlendColor); spriteBatch.Draw(this.texture, this.realm.Offset + this.Position + new Vector2(8, 0), texture_tr, this.BlendColor); spriteBatch.Draw(this.texture, this.realm.Offset + this.Position + new Vector2(0, 8), texture_bl, this.BlendColor); spriteBatch.Draw(this.texture, this.realm.Offset + this.Position + new Vector2(8, 8), texture_br, this.BlendColor); } } ... Any critique or suggestions to my code is welcome. Update: Solution added. Here's the final Level.Draw method. The Level.TileAt method simply checks the inputted values, to avoid OutOfRange exceptions. ... public void Draw(SpriteBatch spriteBatch, GameTime gameTime) { Int32 startx = (Int32)Math.Floor((-this.Offset.X - 32) / 16); Int32 endx = (Int32)Math.Ceiling((-this.Offset.X + 1024 + 32) / 16); Int32 starty = (Int32)Math.Floor((-this.Offset.Y - 32) / 16); Int32 endy = (Int32)Math.Ceiling((-this.Offset.Y + 768 + 32) / 16); for (Int32 x = startx; x < endx; x += 1) { for (Int32 y = starty; y < endy; y += 1) { Tile tile = this.TileAt(x, y); if (tile != null) tile.Draw(spriteBatch, gameTime); } } } ...

  Read the article

• Why the system information message when accessing an Ubuntu server doesn't match free -m?

  - by Andres

  Each time I SSH into my AWS Ubuntu servers I see a system information message, showing load, memory usage and packages available to install, like this: Welcome to Ubuntu 12.04.3 LTS (GNU/Linux 3.2.0-51-virtual x86_64) * Documentation: https://help.ubuntu.com/ System information as of Sun Nov 10 18:06:43 EST 2013 System load: 0.08 Processes: 127 Usage of /: 4.9% of 98.43GB Users logged in: 1 Memory usage: 69% IP address for eth0: 10.236.136.233 Swap usage: 100% Graph this data and manage this system at https://landscape.canonical.com/ 13 packages can be updated. 0 updates are security updates. Get cloud support with Ubuntu Advantage Cloud Guest http://www.ubuntu.com/business/services/cloud Use Juju to deploy your cloud instances and workloads. https://juju.ubuntu.com/#cloud-precise *** /dev/xvda1 will be checked for errors at next reboot *** *** System restart required *** My question is about the memory percentage shown. In this case, it's showing a 69% of memory usage, but since the swap usage was 100% I checked it by myself. So when I run free -m I get this: total used free shared buffers cached Mem: 1652 1635 17 0 4 29 -/+ buffers/cache: 1601 51 Swap: 895 895 0 And that's of course closer to 100% than to 69%

  Read the article

• 4.00gb (3.25gb usable) in Windows 7 x64

  - by dotnetdev

  Hi, I have setup Windows 7 Ultimate x64 on my PC. I have 4gb RAM and my BIOS states the correct amount (4096mb), but I cannot Windows (System Manager) says I have 4.00gb (3.25gb usable). This seems to be a popular issue, and I have looked for an integrated video card (integrated with my chipset) to disable but haven't found anything. What else can be preventing me from seeing all 4gb? When I had Vista 32bit, it would say 3.25gb RAM not 4.00gb (3.25gb usable). I have an x64 CPU and when I brought my RAM, I used a compatibility tool from Crucial (the memory vendor) to test how much memory my PC can support and 4gb was the answer (this was a windows app I think). Chipset is Intel(R) G33/G31/P35/P31 Express Chipset PCI Express In the bios, I looked for an onboard video card (integrated) and there was no such thing, but a couple of other onboard devices. There are also no "Resource Mappings" settings. FURHTER DETAILS: Chipset North Bridge: Intel Bearlake G33 South Bridge: Intel 82801IR ICH9R Maximum Memory Amount 8 GB Graphics Controller Type Intel GMA 3100 (Enabled) I guess the first thing is, how do I disable the graphics controller? EDIT: This thread (http://forums.legitreviews.com/about23417.html) indicates the issue is with memory mapped devices, but someone on this thread says that does not apply to x64. The rest of the comments points to a mobo issue for the guy who started that thread. Thanks

  Read the article

• ubuntu dmidecode is not functioning properly

  - by Alaa Alomari

  dmidecode is giving irrelevant and conflicted results. it shows that i have two slots while the correct is 8 (the board is Tyan S5350.) uname -a Linux synd01 3.0.0-16-server #29-Ubuntu SMP Tue Feb 14 13:08:12 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux root@synd01:/home/badmin# dmidecode -t 16 dmidecode 2.9 SMBIOS 2.33 present. Handle 0x0011, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 2 while root@synd01:/home/badmin# dmidecode -t 17 | grep Size Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB also lshw shows: *-memory description: System Memory physical id: 11 slot: System board or motherboard size: 4GiB *-bank:0 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 0 slot: J3B1 clock: 166MHz (6.0ns) *-bank:1 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 1 slot: J3B3 clock: 166MHz (6.0ns) *-bank:2 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 2 slot: J2B2 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:3 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 3 slot: J2B4 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:4 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 4 slot: J3B2 clock: 166MHz (6.0ns) *-bank:5 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 5 slot: J2B1 clock: 166MHz (6.0ns) *-bank:6 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 6 slot: J2B3 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:7 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 7 slot: J1B1 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) what might cause this conflict and how can i fix it? Thanks

  Read the article

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• quad sli with gtx 690 not working

  - by Moaadh

  I have two cards GTX 690 (dual core). I did the Sli successfully. Nvidia control panel acknowledges the two cards as quad Sli. However, the problem is that Windows 7 64-bit Ultimate is showing me the graph memory size as 4 GB while it is supposed to be 8 GB because of the Sli. Also the benchmark from all software is giving me a very low score compared to some other guy's benchmark on YouTube. It gives me a big headache. Does anyone know why this is happening? If so, how can I get Windows 7 to recognize all 8 GB of memory? Thanks for your help in advance. My computer specifications: (Processor: Intel Core i7-3930k @3.2GHz(12CPUs))--- (Memory: 65536 MB Ram 1866 MHz)-- (OS: Windows 7 Ultimate 64-bit)-- (OCZ 240GB as SSD PCIe drive for booting and storage disk)-- (DirextX version: DirectX 11)-- (VGA Card: 2 X EVGA GTX 690 Dual GPU. Each GPU is 2 GB, so total memory should be 8 GB.)-- (MotherBoard: ASUS Rampage IV Extreme)-- Others with lesser specifications get a 2500 score in heaven benchmark while I get 1501 as if it is one card.

  Read the article

• How to implement didReceiveMemoryWarning ?

  - by hib

  Hello all , I have developed a simple location aware iPhone application which is functionally working very well to our expectations except in the low memory condition of the phone . In low memory condition of the phone my app just got crashes and If I increases the phone memory by freeing up some space it again start working well without any crash . when I do some googling on the problem I found that in the low memory conditions the os will send didReceiveMemoryWarning to all the controllers in the current hierarchy so that each one of them should implement didReceiveMemoryWarning method and also set nil to iboutlet for the view that is currently not visible . I have also read somewhere that if the view for that controller is not visible the method setView with nil parameter will be called and if there are some outlet variables attached to view there will be problem in removing them. So with all these fundas what is the best to handle low level memory condition raised by the Iphone by implementing the didReceiveMemoryWarning and viewDidUnload methods. Please give a proper example or link if possible for the solution of the above problem . thanks.

  Read the article

• UIViewController prevent view from unloading

  - by Ican Zilb

  When my iPhone app receives a Memory warning the views of UIViewControllers that are not currently visible get unloaded. In one particular controller unloading the view and the outlets is rather fatal. I'm looking for a way to prevent this view from being unloaded. I find this behavior rather stupid - I have a cache mechanism, so when a memory warning comes - I unload myself tons of data and I free enough memory, but I definitely need this view untouched. I see UIViewController has a method 'unloadViewIfReloadable', which gets called when the Memory Warning comes. Does anybody know how to tell Cocoa Touch that my view is not reloadable? Any other suggestions how to prevent my view from being unloaded on Memory Warning? Thanks in advance

  Read the article

• What happens when a computer program runs?

  - by gaijinco

  I know the general theory but I can't fit in the details. I know that a program resides in the secondary memory of a computer. Once the program begins execution it is entirely copied to the RAM. Then the processor retrive a few instructions (it depends on the size of the bus) at a time, puts them in registers and executes them. I also know that a computer program uses two kinds of memory: stack and heap, which are also part of the primary memory of the computer. The stack is used for non-dynamic memory, and the heap for dynamic memory (for example, everything related to the new operator in C++) What I can't understand is how those two things connect. At what point is the stack used for the execution of the instructions? Instructions go from the RAM, to the stack, to the registers?

  Read the article

• how to protect an imported win32 dll into a .net application from memory issues

  - by Eric

  I have a c# application that needs to use a legacy win32 dll. The dll is almost its own app, it has dialogs, operations with hardware, etc. When this dll is imported and used, there are a couple of problems that occur: Dragging a dialog (not a windows system dialog, but one created by the dll) across the managed code app causes the UI to not repaint. Further it generates a system out of memory exception from various ui controls. The performance is incredibly slow. There seems to be no way to unload the dll so the memory never gets cleaned up. When we close our managed app, we get another memory exception. At the moment we import each method call as such: [DllImport("dllname.dll", EntryPoint = "MethodName", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]

  Read the article

• Win 7 running slowly with low CPU usage and memory

  - by guywhoneedsahand

  I have a relatively new (under 2 yrs old) windows 7 machine. It has 9GB of RAM, and an i7 core CPU (930 @ 2.8GHz w/ 8 CPUs). After about 8 months since a clean install, I noticed my computer was running slowly. I figure it was fragmentation etc, and I did a complete wipe & clean reinstall. However, my problems are somehow persisting. The computer is running painfully slowly (but in leaps and bounds - sometimes it will work fine for 3 hrs, then suddenly freeze up just from clicking the start button). The 'freezes' happen randomly - not during any especially intensive computing. I initially thought something might be eating through my CPU and/or Memory, but Task Manager indicates that neither the CPU or Memory spike. In fact, even during serious lag, CPU usage remains at less than 5% and Memory at ~ 1.5GB. It's beyond me why a fresh install on a powerful machine is performing so poorly... and it certainly is frustrating! What could be causing the poor performance, and what can I do to fix it?

  Read the article

• Windows Terminal Server: occasional memory violation for applications

  - by syneticon-dj

  On a virtualized (ESXi 4.1) Windows Server 2008 SP2 32-bit machine which is used as a terminal server, I occasionally (approximately 1-3 event log entries a day) see applications fail with an 0xc0000005 error - apparently a memory access violation. The problem seems quite random and only badly reproducable - applications may run for hours, fail with 0xc0000005 and restart quite fine or just throw the access violation at startup and start flawlessly at the second attempt. The names of executables, modules and offset addresses vary, although a single executable tends to fail with same modules and the same memory offset addresses (like "OUTLOOK.EXE" repeatedly failing on module "olmapi32.dll" with the offset "0x00044b7a") - even across multiple user's logons and with several days passing without a single failure inbetween. The offset addresses seem to change across reboots, however. Only selective executables seem affected by the problem, although I may simply not be seeing a sufficient number of application runs from the other ones. I first suspected a possible problem with the physical machine's RAM, but ruled this out as a rather unlikely cause - the memory comes with ECC and I've already moved the virtual machine across several times, without any perceptable change. I've seen that DEP was enabled in "OptOut" mode on this machine: C:\Users\administrator>wmic OS Get DataExecutionPrevention_SupportPolicy DataExecutionPrevention_SupportPolicy 3 and tried changing the policy to OptIn via startup options: bcdedit.exe /set {current} nx OptIn but have yet to see any effect - I also would expect Outlook 12 or Adobe Reader 9 (both affected applications) to play well with DEP. Any other ideas why the apps may be failing?

  Read the article

• Can’t connect to SQL Server 2008 - looks like Shared Memory problem

  - by user38556

  I am unable to connect to my local instance of SQL Server 2008 Express using SQL Server Management Studio. I believe the problem is related to a change I made to the connection protocols. Before the error occurred, I had Shared Memory enabled and Named Pipes and TCP/IP disabled. I then enabled both Named Pipes and TCP/IP, and this is when I started experiencing the problem. When I try to connect to the server with SSMS (with either my SQL server sysadmin login or with windows authentication), I get the following error message: A connection was successfully established with the server, but then an error occurred during the login process. (provider: Named Pipes Provider, error: 0 - No process is on the other end of the pipe.) (Microsoft SQL Server, Error: 233) Why is it returning a Named Pipes error? Why would it not just use Shared Memory, as this has a higher priority order in the list of connection protocols? It seems like it is not listening on Shared Memory for some reason? When I set Named Pipes to enabled and try to connect, I get the same error message. My windows account is does not have administrator priviliges on my computer - perhaps this is making a difference in some way (as some of the discussions in this post about an "SuperSocketNetLib\Lpc" registry key seems to suggest). I have tried restarting the SQL Server service, by the way, and also tried to get someone to log onto the machine with an admin account to restart the SQL Server service. Still no luck.

  Read the article

• Apache process consuming all memory on the server

  - by jemmille

  I have an apache process that suddenly appears on a particular server. When it shows up it starts consuming memory at a very rapid rate, then moves on to all the swap. In all it consumes about 11GB (including swap) of memory and the server eventually becomes unresponsive. The load on the server is under 1 at all other times. The process runs as nobody and I am having a hard time tracking down the source. If i run an strace on the process and all it did was continuously dump out mprotect over and over again If i run lsof -p <pid>, I get this, but only sometimes: httpd 19229 nobody 152u IPv4 175050 crawl-66-249-67-216.googlebot.com:62336 (CLOSE_WAIT) httpd 19229 nobody 153u IPv4 179104 crawl-66-249-71-167.googlebot.com:58012 (ESTABLISHED) As long as I catch it, I can kill the process and the server almost immediately stabilizes. I have on site on the server that is getting a few thousand hits a a day that I think might be the source, but I still can't find the exact reason. Also, this is a cPanel server and I have upcp'd the server, rebuilt apache with easy apache, and rebuilt httpd.conf. It is not spawing any related processes, meaning I can find any php, mysql, cgi, etc. processes that relate to this process. It's just a loner process that balloons fast and consumes ever last MB of memory. This is on a XenServer 5.6 based VM. No other servers in the cluster are having this issue.

  Read the article

• Massive Memory Leaks?

  - by Mads

  Hi, I seem to have huge memory leaks, which are confusing me. I'm running fusion 3.1 / Windows 7 on Snow Leopard. It's a clean install with all upgrades applied. I've given fusion 8GB on a 14GB machine. I've installed VS2008 & Eclipse in Windows 7. Nothing unusual. Inside Task Manager in Windows 7, my memory footprint stays reasonable, at <2GB. But in OSX, Activity Monitor shows the footprint of vmware-vmx to be much larger. It starts at 2 GB, which seems fine, but whenever I'm actually doing anything in Windows, vmware-vmx's footprint grows at a few MB per second. After 20 mins or so it's using ~10GB and everything grinds to a halt. Throughout this, Task Manager still says I'm only using 2GB. And whatever I do in windows seems to increase vmware-vmx's memory footprint. Even closing down an application seems to make it go up. So is this par for the course in fusion? I was previously using parallels 3 / Vista under Leopard, and it worked fine. I'd assumed my new fusion config would work better, but this makes it completely unusable. (And apparently I can't even ask tech support unless I buy a support package...) Any advice much appreciated. Thanks

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >