Search Results

Search found 11482 results on 460 pages for 'portable device'.

Page 90/460 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

  • Wireless not detected on an hp Pavilion g6

    - by Earl Larson
    I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

    Read the article

  • wifi hardware switch doesn't work on a Dell 1018

    - by user42566
    I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

    Read the article

  • ASP.NET MVC WebService - Security for Industrial Android Clients

    - by Chris Nevill
    I'm trying to design a system that will allow a bunch of Android devices to securely log into an ASP.NET MVC REST Web service. At present neither side are implemented. However there is an ASP.NET MVC website which the web service will site along side. This is currently using forms authentication. The idea will be that the Android devices will download data from the web service and then be able to work offline storing data in their own local databases, where users will be able to make updates to that data, and then syncing updates back to the main server where possible. The web service will be using HTTPS to prevent calls being intercepted and reduce the risk of calls being intercepted. The system is an industrial system and will not be in used by the general Android population. Instead only authorized Android devices will be authorized by the Web Service to make calls. As such I was thinking of using the Android devices serial number as a username and then a generated long password which the device will be able to pick up - once the device has been authorized server side. The device will also have user logins - but these will not be to log into the web service - just the device itself - since the device and user must be able to work offline. So usernames and passwords will be downloaded and stored on the devices themselves. My question is... what form of security is best setup on the web service? Should it use forms Authentication? Should the username and password just be passed in with each GET/POST call or should it start a session as I have with the website? The Android side causes more confusion. There seems to be a number of options here Spring-Android, Volley, Retrofit, LoopJ, Robo Spice which seems to use the aforementioned Spring, Retrofit or Google HttpClient. I'm struggling to find a simple example which authenticates with a forms based authentication system. Is this because I'm going about this wrong? Is there another option that would better suite this?

    Read the article

  • format/build raid 5 with one 4k drive, three 512b

    - by skidawgz
    I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

    Read the article

  • SteelSeries & JavaFX External Control via Tinkerforge

    - by Geertjan
    The first photo shows me controling a JavaFX chart by rotating a Tinkerforge device, while the other two are of me using code by Christian Pohl from Nordhorn, Germany, to show components from Gerrit Grunwald's SteelSeries library being externally controled by Tinkerforge devices: What these examples show is that you can have a robot (i.e., an external device), of some kind, that can produce output that can be visualized via JavaFX charts and SteelSeries components. For example, imagine a robot that moves around while collecting data on the current temperature throughout a building. That's possible because a temperature device is part of Tinkerforge, just like the rotating device and distance device shown in the photos above. The temperature data collected by the robot would be displayed in various ways on a computer via, for example, JavaFX charts and SteelSeries components. From there, reports could be produced and adjustments could be made to the robot while it continues moving around collecting temperature data. The fact that Tinkerforge has Wifi support makes a scenario such as described here completely possible to implement. And all of this can be programmed in Java, without very much work, since the Java bindings for Tinkerforge are simple to use, such as shown in yesterday's blog entry.

    Read the article

  • Xorg.conf (nvidia) Second Monitor getting settings of first

    - by HennyH
    I've been spending the weekend (and some time before that) trying to set up my Korean QHD270 and Benq G2222HDL monitors with Ubuntu 13.10. With the nouveau drivers install both monitor function perfectly fine. After installing the nvidia drivers the Benq works but the QHD270 does not. Now, after days of struggling I managed to get the QHD270 to work following a mixture of blogs, particularly; this one and learnitwithme. Now, unfortunatly my G2222HDL does not work. I fixed the QHD270 by supplying a custom EDID, my xorg.conf looks like so (excluding keyboard and mouse): Section "ServerLayout" Identifier "Layout0" Screen "Default Screen" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Section "Device" Identifier "Configured Video Device" Driver "nvidia" Option "CustomEDID" "DFP:/etc/X11/edid-shimian.bin" EndSection Section "Screen" Identifier "Default Screen" Device "Configured Video Device" Monitor "Configured Monitor" EndSection Now, I tried defining a new Device,Monitor and Screen then in ServerLayout adding Screen "Second Screen" RightOf "Default Screen", but after doing so neither monitor worked. Hoping to fix the issue using a GUI based tool I opened up NVIDIA X Server Settings, which shows my current layout as: It seems that something is being output to the monitor, as suggested by my print screen: Any help would be greatly appreciated. Output of xrandr: Screen 0: minimum 8 x 8, current 5120 x 1440, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 connected primary 2560x1440+0+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ HDMI-0 disconnected (normal left inverted right x axis y axis) DP-0 disconnected (normal left inverted right x axis y axis) DVI-D-0 connected 2560x1440+2560+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ DP-1 disconnected (normal left inverted right x axis y axis) And an extract from my log file (perhaps this is relevant?) [ 7.862] (--) NVIDIA(0): Valid display device(s) on GeForce GTX 680 at PCI:2:0:0 [ 7.862] (--) NVIDIA(0): CRT-0 [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0) (boot, connected) [ 7.862] (--) NVIDIA(0): DFP-1 [ 7.862] (--) NVIDIA(0): DFP-2 [ 7.862] (--) NVIDIA(0): DFP-3 [ 7.862] (--) NVIDIA(0): DFP-4 [ 7.862] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): Internal Dual Link TMDS [ 7.862] (--) NVIDIA(0): DFP-1: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-2: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-2: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-3: 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-3: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-4: 960.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-4: Internal DisplayPort

    Read the article

  • Motherboard/PSU crippling USB and Sata

    - by celebdor
    I very recently bought a new desktop computer. The motherboard is: Z77MX-D3H and the power supply is ocz zs series 550w. The issue I have is that once I boot to the operating system (I have tried with fedora and Ubuntu with kernels 2.6.38 - 3.4.0), my hard drive (2.5" Magnetic) occasionally makes a power switch noise and it resets. Needless to say, when this drive is the OS drive, the OS crashes. I also have a SSD that works fine with the same OS configurations, but if I have the magnetic hard drive attached as second drive, it works erratically and the reconnects result in corrupted data. I also noticed that whenever I plug an external hard drive USB2.0 or USB3.0 to the computer the issue with the reconnects is even worse: [ 52.198441] sd 7:0:0:0: [sdc] Spinning up disk... [ 57.955811] usb 4-3: USB disconnect, device number 3 [ 58.023687] .ready [ 58.023914] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.023919] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.023932] sd 7:0:0:0: [sdc] Sense not available. [ 58.024061] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024063] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024064] sd 7:0:0:0: [sdc] Sense not available. [ 58.024099] sd 7:0:0:0: [sdc] Write Protect is off [ 58.024101] sd 7:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 58.024135] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024137] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024400] sd 7:0:0:0: [sdc] READ CAPACITY(16) failed [ 58.024402] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024405] sd 7:0:0:0: [sdc] Sense not available. [ 58.024448] sd 7:0:0:0: [sdc] READ CAPACITY failed [ 58.024450] sd 7:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 58.024451] sd 7:0:0:0: [sdc] Sense not available. [ 58.024469] sd 7:0:0:0: [sdc] Asking for cache data failed [ 58.024471] sd 7:0:0:0: [sdc] Assuming drive cache: write through [ 58.024472] sd 7:0:0:0: [sdc] Attached SCSI disk [ 58.407725] usb 4-3: new SuperSpeed USB device number 4 using xhci_hcd [ 58.424921] scsi8 : usb-storage 4-3:1.0 [ 59.424185] scsi 8:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 59.424406] scsi 8:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 59.425098] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 59.425176] ses 8:0:0:1: Attached Enclosure device [ 59.425248] ses 8:0:0:1: Attached scsi generic sg3 type 13 [ 61.845836] sd 8:0:0:0: [sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 61.845838] sd 8:0:0:0: [sdc] 4096-byte physical blocks [ 61.846336] sd 8:0:0:0: [sdc] Write Protect is off [ 61.846338] sd 8:0:0:0: [sdc] Mode Sense: 47 00 10 08 [ 61.846718] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.846720] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.848105] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.848106] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.857147] sdc: sdc1 [ 61.858915] sd 8:0:0:0: [sdc] No Caching mode page present [ 61.858916] sd 8:0:0:0: [sdc] Assuming drive cache: write through [ 61.858918] sd 8:0:0:0: [sdc] Attached SCSI disk [ 69.875809] usb 4-3: USB disconnect, device number 4 [ 70.275816] usb 4-3: new SuperSpeed USB device number 5 using xhci_hcd [ 70.293063] scsi9 : usb-storage 4-3:1.0 [ 71.292257] scsi 9:0:0:0: Direct-Access WD My Passport 0740 1003 PQ: 0 ANSI: 6 [ 71.292505] scsi 9:0:0:1: Enclosure WD SES Device 1003 PQ: 0 ANSI: 6 [ 71.293527] sd 9:0:0:0: Attached scsi generic sg2 type 0 [ 71.293668] ses 9:0:0:1: Attached Enclosure device [ 71.293758] ses 9:0:0:1: Attached scsi generic sg3 type 13 [ 73.323804] usb 4-3: USB disconnect, device number 5 [ 101.868078] ses 9:0:0:1: Device offlined - not ready after error recovery [ 101.868124] ses 9:0:0:1: Failed to get diagnostic page 0x50000 [ 101.868131] ses 9:0:0:1: Failed to bind enclosure -19 [ 101.868288] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868292] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868296] sd 9:0:0:0: [sdc] Sense not available. [ 101.868428] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868434] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868439] sd 9:0:0:0: [sdc] Sense not available. [ 101.868468] sd 9:0:0:0: [sdc] Write Protect is off [ 101.868473] sd 9:0:0:0: [sdc] Mode Sense: 00 00 00 00 [ 101.868580] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868584] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868845] sd 9:0:0:0: [sdc] READ CAPACITY(16) failed [ 101.868849] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868854] sd 9:0:0:0: [sdc] Sense not available. [ 101.868894] sd 9:0:0:0: [sdc] READ CAPACITY failed [ 101.868898] sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 101.868903] sd 9:0:0:0: [sdc] Sense not available. [ 101.868961] sd 9:0:0:0: [sdc] Asking for cache data failed [ 101.868966] sd 9:0:0:0: [sdc] Assuming drive cache: write through [ 101.868969] sd 9:0:0:0: [sdc] Attached SCSI disk Now, if I plug the same drive to the powered usb 2.0 hub of my monitor, the issue is not reproduced (at least on a 20h long operation). Also the issue of the usb reconnects is less frequent if the hard drive is plugged before I switch on the computer. Does anybody have some advice as to what I could do? Which is the faulty part/s that I should replace? As for me, I really don't know if to point my finger to the PSU or the Motherboard (I have updated to the latest firmware and checked the BIOS settings several times). EDIT: The reconnects are happening both in the Sata connected drives and the USBX connected drives.

    Read the article

  • Game Center: Leaderboard score inconsistencies

    - by Hasyimi Bahrudin
    Background I'm currently developing a simple library that mirrors Game Center's functionalities locally. Basically, this library is a system that manages achievements and leaderboards, and optionally sync it with the Game Center. So, if the game is not GC enabled, the game will still have achievements and leaderboards (stored inside a plist). But of course, the leaderboards will then only contain the local player's scores (which is kind of useless, I know :P). Problem Currently I have coded both of the achievements and leaderboards subsystems. The achievements subsystem have already been tested and it works. I'm currently testing the leaderboards subsystem using multiple test user accounts. I loaded the test app on a device and on the simulator, both logged in with 2 different user accounts. Then I performed these steps: I first used the device to upload a score. Then, I ran the simulator, and the score submitted by the user on the device is shown. Which is cool. Then, I used the simulator to upload a score. But on the device, still, only one score is listed. I checked on the Game Center app (to see if the bug lies within my code), and I got the same thing. Under "All players", there is only one score on the device, but there are 2 scores on the simulator. I wanted to make sure that the simulator is not causing this, so I swapped the users on the device and the simulator, and the result is still the same. In other words, the first user is oblivious of the second user's score, but the second user can see the first user's score. Then I tried with a third user. The result: the third user can only see the scores of the first user and himself. The second user still sees the scores of the first user and himself. The first user only sees his own score. Now here comes the weird part. I then make the first user and the second user befriend each other. The result: under "Friends", the first user can see the second user's score, but under "All Players", the first user's score is the only one listed. Screenshots The first user sees this: The second user sees this: So, is this a normal thing when using sandboxed GC accounts? Is this behavior documented somewhere by Apple?

    Read the article

  • Commercial version of Freenet6

    - by grnbeagle
    I've been using Freenet6 from gogoNET to make my mobile device publicly accessible via IPv6. It works quite well except that the service is not as stable because it's non-commercial usage only as their servers are hosted for free by different operators around the world. Apparently gogoNET sells hardware called gogoSERVER which allows one to build a service similar to Freenet6. I've inquired their sales team, but they were unable to tell me which companies have a commercial, production-quality implementation of Freenet6. Specifically I'm looking for the following features in IPv6 service provider: Client-based IPv6 connectivity for mobile devices: gogoCLIENT (gw6c) is ideal for mobile devices since it allows a device to go online regardless of the device's location. API for account maintenance: so that we can create device accounts from our software Static IPv6 address: (or maybe I mean IPv4 address) by this I mean, just like gogoNET6 service (username.broker.freenet6.net), we want to provide our users with a permanent URL for their device Any info on commercial IPv6 service provider utilizing gogoSERVER is appreciated. Thanks.

    Read the article

  • Detecting/Reactivating serial port that becomes inactive on Ubuntu Linux 10.10

    - by Tom
    I am using a usb2serial port to communicate with some old equipment (using my code built upon the boost asio library - I think my code is fine because it works almost all of the time). Every so often (maybe once every few days) the communication stops with my device with no error at all - the device just does not respond. I then restart my computer and everything is fine again. Does anyone know where I can start to analyse this problem? My serial port loads up fine (in /dev/ttyUSB0) and the boost library does not throw an error. The device just does not respond. If I restart the device no change - only when I restart my pc does it make a difference. I have also tried unplugging and replugging the usb connector. Does anyone know what gets cleared in the reboot (w.r.t the serial device) or what I can probe when the problem happens again (rather than just restarting with hope)

    Read the article

  • NMap route determination on Windows 7 x64

    - by user30772
    C:\Windows\system32>nmap --iflist Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 06:51 Central Daylight Time ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MTU MAC eth0 (eth0) fe80::797f:b9b6:3ee0:27b8/64 ethernet down 1500 5C:AC:4C:E9:2D:46 eth0 (eth0) 169.254.39.184/4 ethernet down 1500 5C:AC:4C:E9:2D:46 eth1 (eth1) fe80::5c02:7e48:8fbe:c7c9/64 ethernet down 1500 00:FF:3F:7C:7C:2B eth1 (eth1) 169.254.199.201/4 ethernet down 1500 00:FF:3F:7C:7C:2B eth2 (eth2) fe80::74e4:1ab7:1b7d:a0d0/64 ethernet up 1500 14:FE:B5:BA:8A:C3 eth2 (eth2) 10.0.0.0.253/24 ethernet up 1500 14:FE:B5:BA:8A:C3 eth3 (eth3) fe80::b03e:ddf5:bb5c:5f76/64 ethernet up 1500 00:50:56:C0:00:01 eth3 (eth3) 169.254.95.118/16 ethernet up 1500 00:50:56:C0:00:01 eth4 (eth4) fe80::b175:831d:e60:27b/64 ethernet up 1500 00:50:56:C0:00:08 eth4 (eth4) 192.168.153.1/24 ethernet up 1500 00:50:56:C0:00:08 lo0 (lo0) ::1/128 loopback up -1 lo0 (lo0) 127.0.0.1/8 loopback up -1 tun0 (tun0) fe80::100:7f:fffe/64 point2point down 1280 tun1 (tun1) (null)/0 point2point down 1280 tun2 (tun2) fe80::5efe:a9fe:5f76/128 point2point down 1280 tun3 (tun3) (null)/0 point2point down 1280 tun4 (tun4) fe80::5efe:c0a8:9901/128 point2point down 1280 tun5 (tun5) fe80::5efe:ac14:fd/128 point2point down 1280 DEV WINDEVICE eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth0 \Device\NPF_{0024872A-5A41-42DF-B484-FB3D3ED3FCE9} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth1 \Device\NPF_{3F7C7C2B-9AF3-45BB-B96E-2F00143CC2F7} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth2 \Device\NPF_{08116FE5-F0FF-498A-9BF1-515528C57C13} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth3 \Device\NPF_{AA83C6CE-AB2E-4764-92D1-CDEAFBA7AD21} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} eth4 \Device\NPF_{D0679889-E9D4-411D-BDC5-F4DDB758E151} lo0 <none> lo0 <none> tun0 <none> tun1 <none> tun2 <none> tun3 <none> tun4 <none> tun5 <none> **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 JMeterX - I worded that way in hopes of raising answer efficnecy, but that probably wasnt the smartest choice. IMHO the problem (could be a symptom) is that nmap retardedly chooses eth0 as the gateway interface for any and all networks. Here's the result: C:\Windows\system32>nmap 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:43 Central Daylight Time Note: Host seems down. If it is really up, but blocking our ping probes, try -Pn Nmap done: 1 IP address (0 hosts up) scanned in 0.95 seconds C:\Windows\system32>nmap -e eth2 10.0.0.55 Starting Nmap 6.01 ( http://nmap.org ) at 2012-08-31 07:44 Central Daylight Time Nmap scan report for esxy5.dionne.net (10.0.0.55) Host is up (0.00070s latency). Not shown: 991 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 427/tcp open svrloc 443/tcp open https 902/tcp open iss-realsecure 5988/tcp closed wbem-http 5989/tcp open wbem-https 8000/tcp open http-alt 8100/tcp open xprint-server MAC Address: 00:1F:29:59:C7:03 (Hewlett-Packard Company) Nmap done: 1 IP address (1 host up) scanned in 5.29 seconds Just to be clear, this is what makes absolutly no sense to me whatsoever. For reference, I've included similar info from an Ubuntu (that works normally) vm on the affected host below. Jacked Windows 7 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.153.255/32 eth0 255.255.255.255/32 eth0 255.255.255.255/32 eth0 127.0.0.1/32 eth0 127.255.255.255/32 eth0 255.255.255.255/32 eth0 169.254.95.118/32 eth0 169.254.255.255/32 eth0 10.0.0.0.253/32 eth0 255.255.255.255/32 eth0 10.0.0.0.255/32 eth0 255.255.255.255/32 eth0 192.168.153.1/32 eth0 255.255.255.255/32 eth0 10.0.0.0.0/24 eth0 192.168.153.0/24 eth0 10.10.10.0/24 eth0 10.0.0.0.4 169.254.0.0/16 eth0 127.0.0.0/8 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 224.0.0.0/4 eth0 0.0.0.0/0 eth0 10.0.0.0.1 Working Ubuntu VM root@ubuntu:~# nmap --iflist Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT ************************INTERFACES************************ DEV (SHORT) IP/MASK TYPE UP MAC lo (lo) 127.0.0.1/8 loopback up eth0 (eth0) 172.20.0.89/24 ethernet up 00:0C:29:0A:C9:35 eth1 (eth1) 192.168.225.128/24 ethernet up 00:0C:29:0A:C9:3F eth2 (eth2) 192.168.150.128/24 ethernet up 00:0C:29:0A:C9:49 **************************ROUTES************************** DST/MASK DEV GATEWAY 192.168.225.0/0 eth1 192.168.150.0/0 eth2 172.20.0.0/0 eth0 169.254.0.0/0 eth0 0.0.0.0/0 eth0 172.20.0.1 root@ubuntu:~# nmap esxy2 Starting Nmap 5.21 ( http://nmap.org ) at 2012-08-31 07:44 PDT Nmap scan report for esxy2 (172.20.0.52) Host is up (0.00036s latency). rDNS record for 172.20.0.52: esxy2.dionne.net Not shown: 994 filtered ports PORT STATE SERVICE 80/tcp open http 427/tcp closed svrloc 443/tcp open https 902/tcp closed iss-realsecure 8000/tcp open http-alt 8100/tcp open unknown MAC Address: 00:04:23:B1:FA:6A (Intel) Nmap done: 1 IP address (1 host up) scanned in 4.76 seconds

    Read the article

  • ntfsresize volume and size information

    - by antonio
    I am going to resize my sda2 NTFS partition. When gathering info with ntfsresize, I get: ntfsresize --info /dev/sda2 ntfsresize v2013.1.13 (libntfs-3g) Device name : /dev/sda2 NTFS volume version: 3.1 Cluster size : 4096 bytes Current volume size: 21999993344 bytes (22000 MB) Current device size: 23622320128 bytes (23623 MB) Checking filesystem consistency ... Accounting clusters ... Space in use : 10673 MB (48.5%) Collecting resizing constraints ... You might resize at 10672590848 bytes or 10673 MB (freeing 11327 MB). Please make a test run using both the -n and -s options before real resizing! Can you tell me what is the difference between volume and device size? As for device size, 23622320128 bytes / 1000^2 = 23622.3 MB. Why is 23623 MB reported instead of 23622? Note that parted confirms this value: parted /dev/sda2 unit MB p Model: Unknown (unknown) Disk /dev/sda2: 23622MB Sector size (logical/physical): 512B/512B Partition Table: loop Disk Flags: Number Start End Size File system Flags 1 0.00MB 23622MB 23622MB ntfs

    Read the article

  • Firefox profile issue

    - by vooda gopal
    Is there any limit in the number of firefox profiles that can be created? My issue is I am currently doing selenium webdriver automation in linux for a device. There are 50 devices of same kind and framework will pickup a device depending on availability. I need to by pass unsigned ssl pages. I am using firefox 14. I have implemented following but it is not consistent. everytime a device is chosen adds cer of device to the cert file in firefox profile but I am getting sec_error_bad_signature very frequently. So I started recreating cert [delete and create if by opening firefox] file for every run. Now this is posing a problem if multiple devices are run at the same time. Hence I want to create separate firefox profile

    Read the article

  • Nexus 7 Possibly Bricked

    - by user214186
    I have a 1st gen Nexus 7 (32GB). I used the steps at https://wiki.ubuntu.com/Nexus7/Installation to successfully install Ubuntu 13.04 desktop onto the tablet. It was working fine and then I decided to upgrade to Ubuntu Touch. I booted the tablet into fast boot mode but the commands 'adb devices' and 'sudo fastboot devices' would not see the device. I am performing these steps from an Ubuntu 12.04 desktop PC. Prior to installing 13.04 the device was seen fine. I made the mistake of performing the 'Device factory reset' step from https://wiki.ubuntu.com/Touch/Install - Step 2. Now when I try to boot the device I get the following: mount: mounting /dev on /root/dev failed: no such file or directory mount: mounting /dev on /root/sys failed: no such file or directory mount: mounting /proc on /root/proc failed: no such file or directory Targe filesystem doesn't have requested /sbin/init. No init found. Try passing init= bootarg. BusyBox v1.20.2 (Ubuntu 1:1.20.0-0ubuntu1) built-in shell (ash) Enter help for a list of built-in commands. (initramfs) I have searched the web but every reference to this problem is from people who still have ADB access to the device so they can recover by flashing the tablet again. I can attach a keyboard to the USB port and access the BusyBox console but I don't know what steps to do to recover from my error. Any suggestions would be helpful. Thanks

    Read the article

  • Can not print after upgrading from 12.x to 14.04

    - by user318889
    After upgrading from V12.04 to V14.04 I am not able to print. I am using an HP LaserJet 400 M451dn. The printer troubleshooter told me that there is no solution to the problem. This is the output of the advanced diagnositc output. (Due to limited space I cut the output!) Can anybody tell me what is going wrong. I am using the printer via USB ? Page 1 (Scheduler not running?): {'cups_connection_failure': False} Page 2 (Is local server publishing?): {'local_server_exporting_printers': False} Page 3 (Choose printer): {'cups_dest': , 'cups_instance': None, 'cups_queue': u'HP-LaserJet-400-color-M451dn', 'cups_queue_listed': True} Page 4 (Check printer sanity): {'cups_device_uri_scheme': u'hp', 'cups_printer_dict': {'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'printer-info': u'Hewlett-Packard HP LaserJet 400 color M451dn', 'printer-is-shared': True, 'printer-location': u'Pinatubo', 'printer-make-and-model': u'HP LJ 300-400 color M351-M451 Postscript (recommended)', 'printer-state': 4, 'printer-state-message': u'', 'printer-state-reasons': [u'none'], 'printer-type': 8556636, 'printer-uri-supported': u'ipp://localhost:631/printers/HP-LaserJet-400-color-M451dn'}, 'cups_printer_remote': False, 'hplip_output': (['', '\x1b[01mHP Linux Imaging and Printing System (ver. 3.14.6)\x1b[0m', '\x1b[01mDevice Information Utility ver. 5.2\x1b[0m', '', 'Copyright (c) 2001-13 Hewlett-Packard Development Company, LP', 'This software comes with ABSOLUTELY NO WARRANTY.', 'This is free software, and you are welcome to distribute it', 'under certain conditions. See COPYING file for more details.', '', '', '\x1b[01mhp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '', '\x1b[01mDevice Parameters (dynamic data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' back-end hp ', " cups-printers ['HP-LaserJet-400-color-M451dn'] ", ' cups-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' dev-file ', ' device-state -1 ', ' device-uri hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670 ', ' deviceid ', ' error-state 101 ', ' host ', ' is-hp True ', ' panel 0 ', ' panel-line1 ', ' panel-line2 ', ' port 1 ', ' serial CNFF308670 ', ' status-code 5002 ', ' status-desc ', '\x1b[01m', 'Model Parameters (static data):\x1b[0m', '\x1b[01m Parameter Value(s) \x1b[0m', ' ---------------------------- ----------------------------------------------------------', ' align-type 0 ', ' clean-type 0 ', ' color-cal-type 0 ', ' copy-type 0 ', ' embedded-server-type 0 ', ' fax-type 0 ', ' fw-download False ', ' icon hp_color_laserjet_cp2025.png ', ' io-mfp-mode 1 ', ' io-mode 1 ', ' io-support 6 ', ' job-storage 0 ', ' linefeed-cal-type 0 ', ' model HP_LaserJet_400_color_M451dn ', ' model-ui HP LaserJet 400 Color m451dn ', ' model1 HP LaserJet 400 Color M451dn ', ' monitor-type 0 ', ' panel-check-type 0 ', ' pcard-type 0 ', ' plugin 0 ', ' plugin-reason 0 ', ' power-settings 0 ', ' ppd-name lj_300_400_color_m351_m451 ', ' pq-diag-type 0 ', ' r-type 0 ', ' r0-agent1-kind 4 ', ' r0-agent1-sku CE410A/CE410X ', ' r0-agent1-type 1 ', ' r0-agent2-kind 4 ', ' r0-agent2-sku CE411A ', ' r0-agent2-type 4 ', ' r0-agent3-kind 4 ', ' r0-agent3-sku CE413A ', ' r0-agent3-type 5 ', ' r0-agent4-kind 4 ', ' r0-agent4-sku CE412A ', ' r0-agent4-type 6 ', ' scan-src 0 ', ' scan-type 0 ', ' status-battery-check 0 ', ' status-dynamic-counters 0 ', ' status-type 3 ', ' support-released True ', ' support-subtype 2202411 ', ' support-type 2 ', ' support-ver 3.12.2 ', " tech-class ['Postscript'] ", " tech-subclass ['Normal'] ", ' tech-type 4 ', ' usb-pid 3882 ', ' usb-vid 1008 ', ' wifi-config 0 ', '\x1b[01m', 'Status History (most recent first):\x1b[0m', '\x1b[01m Date/Time Code Status Description User Job ID \x1b[0m', ' -------------------- ----- ---------------------------------------- -------- --------', ' 08/21/14 00:07:25 5012 Device communication error richard 0 ', ' 08/20/14 13:42:44 500 Started a print job richard 4214 ', '', '', 'Done.', ''], ['\x1b[35;01mwarning: No display found.\x1b[0m', '\x1b[31;01merror: hp-info -u/--gui requires Qt4 GUI support. Entering interactive mode.\x1b[0m', '\x1b[31;01merror: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670\x1b[0m', '\x1b[31;01merror: Error opening device (Device not found).\x1b[0m', ''], 0), 'is_cups_class': False, 'local_cups_queue_attributes': {'charset-configured': u'utf-8', 'charset-supported': [u'us-ascii', u'utf-8'], 'color-supported': True, 'compression-supported': [u'none', u'gzip'], 'copies-default': 1, 'copies-supported': (1, 9999), 'cups-version': u'1.7.2', 'device-uri': u'hp:/usb/HP_LaserJet_400_color_M451dn?serial=CNFF308670', 'document-format-default': u'application/octet-stream', 'document-format-supported': [u'application/octet-stream', u'application/pdf', u'application/postscript', u'application/vnd.adobe-reader-postscript', u'application/vnd.cups-command', u'application/vnd.cups-pdf', u'application/vnd.cups-pdf-banner', u'application/vnd.cups-postscript', u'application/vnd.cups-raw', u'application/vnd.samsung-ps', u'application/x-cshell', u'application/x-csource', u'application/x-perl', u'application/x-shell', u'image/gif', u'image/jpeg', u'image/png', u'image/tiff', u'image/urf', u'image/x-bitmap', u'image/x-photocd', u'image/x-portable-anymap', u'image/x-portable-bitmap', u'image/x-portable-graymap', u'image/x-portable-pixmap', u'image/x-sgi-rgb', u'image/x-sun-raster', u'image/x-xbitmap', u'image/x-xpixmap', u'image/x-xwindowdump', u'text/css', u'text/html', u'text/plain'], 'finishings-default': 3, 'finishings-supported': [3], 'generated-natural-language-supported': [u'en-us'], 'ipp-versions-supported': [u'1.0', u'1.1', u'2.0', u'2.1'], 'ippget-event-life': 15, 'job-creation-attributes-supported': [u'copies', u'finishings', u'ipp-attribute-fidelity', u'job-hold-until', u'job-name', u'job-priority', u'job-sheets', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-hold-until-default': u'no-hold', 'job-hold-until-supported': [u'no-hold', u'indefinite', u'day-time', u'evening', u'night', u'second-shift', u'third-shift', u'weekend'], 'job-ids-supported': True, 'job-k-limit': 0, 'job-k-octets-supported': (0, 470914416), 'job-page-limit': 0, 'job-priority-default': 50, 'job-priority-supported': [100], 'job-quota-period': 0, 'job-settable-attributes-supported': [u'copies', u'finishings', u'job-hold-until', u'job-name', u'job-priority', u'media', u'media-col', u'multiple-document-handling', u'number-up', u'output-bin', u'orientation-requested', u'page-ranges', u'print-color-mode', u'print-quality', u'printer-resolution', u'sides'], 'job-sheets-default': (u'none', u'none'), 'job-sheets-supported': [u'none', u'classified', u'confidential', u'form', u'secret', u'standard', u'topsecret', u'unclassified'], 'jpeg-k-octets-supported': (0, 470914416), 'jpeg-x-dimension-supported': (0, 65535), 'jpeg-y-dimension-supported': (1, 65535), 'marker-change-time': 0, 'media-bottom-margin-supported': [423], 'media-col-default': u'(unknown IPP value tag 0x34)', 'media-col-supported': [u'media-bottom-margin', u'media-left-margin', u'media-right-margin', u'media-size', u'media-source', u'media-top-margin', u'media-type'], 'media-default': u'iso_a4_210x297mm', 'media-left-margin-supported': [423], 'media-right-margin-supported': [423],

    Read the article

  • Cannot boot into ubuntu 12.10

    - by sriram
    Below given are the steps which I followed to install ubuntu 12.10 with existing windows 8 in my machine. I downloaded ubuntu 12.10 into my disk and made it bootable from my usb by selecting that iso file. Then restared my mahine and in BIOS I selected boot from usb. Went into Linux os and selected install ubuntu alongside windows 8. It asked for memory allocation and I selected 550 GB for Ubuntu and 404GB for Windows. After that it completed ubuntu installation. The booted into my windows 8 and used easyBCD to add a new entry. Ubuntu grup2 Now the easyBCD shows, There are a total of 4 entries listed in the bootloader. Default: Windows 8 Timeout: 10 seconds EasyBCD Boot Device: C:\ Entry #1 Name: Lenovo Recovery System BCD ID: {e58d0cb6-2eae-11e2-9d20-806e6f6e6963} Device: \Device\HarddiskVolume3 Bootloader Path: \EFI\Microsoft\Boot\LrsBootMgr.efi Entry #2 Name: EFI USB Device BCD ID: {e58d0cb5-2eae-11e2-9d20-806e6f6e6963} Device: Unknown Bootloader Path: Entry #3 Name: Windows 8 BCD ID: {current} Drive: C:\ Bootloader Path: \windows\system32\winload.efi Entry #4 Name: Ubuntu 12.10 BCD ID: {6f173570-3bce-11e2-be74-c0143dd589c0} Drive: C:\ Bootloader Path: \NST\AutoNeoGrub0.mbr Next I restarted my system and in the boot options it shows windows 8 and ubuntu 12.10 When I click on ubuntu it displays, \NST\AutoNeoGrub0.mbr status 0xc000007b The application or operating system cold not be loaded because a required file is missing or contains errors. Can you help me resolve this... Thanks :)

    Read the article

  • How do I start xterm with a headless system?

    - by NeViXa
    I'm running Ubuntu 12.04 and I want to boot directly and headless in the terminal (no GUI). After that I want to startx to start a program in xterm. When I boot 'headed', everything is working like supposed to, but: - When I boot headless, startx is not working (no screens found) I already tried to change xorg.conf to below, but it didn't not work: Section "Device" Identifier "VNC Device" Driver "vesa" EndSection Section "Screen" Identifier "VNC Screen" Device "VNC Device" Monitor "VNC Monitor" SubSection "Display" Modes "1280x1024" EndSubSection EndSection Section "Monitor" Identifier "VNC Monitor" HorizSync 30-70 VertRefresh 50-75 EndSection How can I boot headless and still be able to run startx? ANSWER: Adding the BusID to the Devices section in the xorg.conf above, fixed the problem for me. BusID "PCI:1:00:1"

    Read the article

  • Incomplete mesh using DrawIndexedPrimitives after rotating mesh

    - by user1278255
    Through help on this site I was able to draw the triangles of an unrotated, nonscaled nontransformed mesh created in Blender and exported to OBJ, accurately imported through Assimp and rendered in XNA Graphics. However after applying rotation on a single axis in Blender(Z) and adding materials(I wanted to test loading of materials through Assimp) the same mesh appears incomplete. Is something wrong with my view matrix or is it something else? This is what the unrotated mesh looks like: http://www.4shared.com/photo/qXNUSvxtba/okcube.html Here is the rotated mesh: http://www.4shared.com/photo/HAys2rWvba/badcube.html Camera, View and Projection are defined as follows: cameraPos = new Vector3(0, 5, 9); viewMatrix = Matrix.CreateLookAt(cameraPos, new Vector3(0, 0, 1), new Vector3(0, 1, 0)); projectionMatrix = Matrix.CreatePerspectiveFieldOfView(MathHelper.PiOver4, device.Viewport.AspectRatio, 1.0f, 200.0f); Rendering is done through this code: device.Clear(ClearOptions.Target | ClearOptions.DepthBuffer, Color.DarkSlateBlue, 1.0f, 0); effect = new BasicEffect(GraphicsDevice); effect.VertexColorEnabled = true; effect.View = viewMatrix; effect.Projection = projectionMatrix; effect.World = Matrix.Identity; foreach (EffectPass pass in effect.CurrentTechnique.Passes) { pass.Apply(); device.SetVertexBuffer(vertexBuffer); device.Indices = indexBuffer; device.DrawIndexedPrimitives(Microsoft.Xna.Framework.Graphics.PrimitiveType.TriangleList, 0, 0, oScene.Meshes[0].VertexCount, 0, mMesh.FaceCount); } base.Draw(gameTime);

    Read the article

  • Cool projects at Codeplex

    - by Tiago Salgado
    There’s a significant number of useful projects at Codeplex who were meeting with some of our needs. As such, here are two that already have been useful to me: Droid Explorer As the name implies, allows us to explore an Android device and has features such as: Copy local files to device Reboot device Reboot device in to recovery mode Open files for viewing / execution locally with the default file type executable Package Manager (Install & Uninstall) Take a Screen Shot (landscape or portrait) etc Virtual Router – Wifi Hot Spot (Windows 7 / 2008 R2) Allows you to create an Access Point, sharing your local Internet connection, with other wireless devices. Its no doubt an application to be always installed, by the simple way to create a resource like this one.

    Read the article

  • Dosbox has no sound

    - by satuon
    I try to run a game under dosbox, but it has no sound, and in the terminal dosbox says: MIXER:Can't open audio: No available audio device , running in nosound mode. ALSA:Can't subscribe to MIDI port (65:0) nor (17:0) MIDI:Opened device:none Update I changed the ports to 128:0 in the dosbox config file and now it says ALSA:Client initialised [128:0] MIDI:Opened device:alsa but still no sound :(

    Read the article

  • How do I draw a single Triangle with XNA and fill it with a Texture?

    - by Deukalion
    I'm trying to wrap my head around: http://msdn.microsoft.com/en-us/library/bb196409.aspx I'm trying to create a method in XNA that renders a single Triangle, then later make a method that takes a list of Triangles and renders them also. But it isn't working. I'm not understanding what all the things does and there's not enough information. My methods: // Triangle is a struct with A, B, C (didn't include) A, B, C = Vector3 public static void Render(GraphicsDevice device, List<Triangle> triangles, Texture2D texture) { foreach (Triangle triangle in triangles) { Render(device, triangle, texture); } } public static void Render(GraphicsDevice device, Triangle triangle, Texture2D texture) { BasicEffect _effect = new BasicEffect(device); _effect.Texture = texture; _effect.VertexColorEnabled = true; VertexPositionColor[] _vertices = new VertexPositionColor[3]; _vertices[0].Position = triangle.A; _vertices[1].Position = triangle.B; _vertices[2].Position = triangle.B; foreach (var pass in _effect.CurrentTechnique.Passes) { pass.Apply(); device.DrawUserIndexedPrimitives<VertexPositionColor> ( PrimitiveType.TriangleList, _vertices, 0, _vertices.Length, new int[] { 0, 1, 2 }, // example has something similiar, no idea what this is 0, 3 // 3 = gives me an error, 1 = works but no results ); } }

    Read the article

  • Only One GPU Detected in the Nvidia Quadra NVS 450

    - by Kyle Brandt
    I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia... Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there): # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010 Section "ServerLayout" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor2" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+275, DFP-3: nvidia-auto-select +1680+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-3" Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-3: nvidia-auto-select +1680+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "DFP-3: nvidia-auto-select +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection lscpi: 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:02.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer Registers Port 0 (rev 13) 00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol Layer Registers Port 0 (rev 13) 00:11.0 PIC: Intel Corporation 5520/5500 Physical and Link Layer Registers Port 1 (rev 13) 00:11.1 PIC: Intel Corporation 5520/5500 Routing & Protocol Layer Register Port 1 (rev 13) 00:13.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub I/OxAPIC Interrupt Controller (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:15.0 PIC: Intel Corporation 5520/5500/X58 Trusted Execution Technology Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.3 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 4 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 01:00.0 IDE interface: Device 1b4b:91a3 (rev 11) 02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) 03:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:02.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 05:00.0 3D controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 06:00.0 VGA compatible controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 08:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 08:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0b:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)

    Read the article

  • How can a usb be detected but not show up anywhere?

    - by George Mauer
    I started the morning by trying to create a bootable usb using a 2gb stick and the startup disk creator. It seemed to run through the whole process just fine until it got to a screen that read something like "Creating memory partion" and which sat on 100% for about 45 minutes before I hit cancel and removed the usb stick. Now the usb stick is not being detected as storage or...anything (even on my windows pc) though it does show up in the syslog. Allow me to demonstrate. We start with the usb not plugged in: [georgemauer@ubuntu:~]$ sudo fdisk -l (04-04 16:01) Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x994bdc0f Device Boot Start End Blocks Id System /dev/sda1 2048 27650047 13824000 27 Hidden NTFS WinRE /dev/sda2 * 27650048 27854847 102400 7 HPFS/NTFS/exFAT /dev/sda3 27854848 976771119 474458136 7 HPFS/NTFS/exFAT I plug in the usb: [georgemauer@ubuntu:~]$ tail -f /var/log/syslog ***Snip*** Apr 4 15:01:18 ubuntu wpa_supplicant[1136]: WPA: Group rekeying completed with 00:24:36:ad:e7:3f [GTK=TKIP] Apr 4 15:02:29 wpa_supplicant[1136]: last message repeated 3 times Apr 4 15:02:29 ubuntu kernel: [22122.788133] usb 2-1: new high speed USB device number 13 using ehci_hcd Apr 4 15:02:29 ubuntu kernel: [22122.923873] scsi10 : usb-storage 2-1:1.0 Apr 4 15:02:29 ubuntu mtp-probe: checking bus 2, device 13: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-1" Apr 4 15:02:30 ubuntu mtp-probe: bus: 2, device: 13 was not an MTP device Apr 4 15:02:30 ubuntu kernel: [22123.926154] scsi 10:0:0:0: Direct-Access GENERIC USB Mass Storage 1.00 PQ: 0 ANSI: 2 Apr 4 15:02:30 ubuntu kernel: [22124.105118] sd 10:0:0:0: Attached scsi generic sg1 type 0 Apr 4 15:02:30 ubuntu kernel: [22124.108212] sd 10:0:0:0: [sdb] Attached SCSI removable disk but then: [georgemauer@ubuntu:~]$ ls /mnt -alF (04-04 16:02) total 8 drwxr-xr-x 2 root root 4096 2011-04-21 12:51 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ [georgemauer@ubuntu:~]$ ls /media -alF (04-04 16:03) total 8 drwxr-xr-x 2 root root 4096 2012-04-04 12:18 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ What could be going on and how do I recover my usb key?

    Read the article

  • Windows XP Home Edition SP3 cant recognise PCMIA SD Card

    - by Pozo
    System Specifications: Laptop : Dell Inspiron 6000 OS: Windows Home Edition SP3 SD Adapter: Hagiwara Smart Media Adapter I inserted the card into the slot, windows xp recognises the device, lists the pcmia controller on the device manager list, an entry appears under the IDE ATA/ATAPI category on the device manager as well. However, the device does not show under my computer and the driver does not get assigned a letter number. I checked the system logs from the device manager and there were no logged errors. Checking the Hagiwara support website, the manufacturer indicates that the adapter driver is the same as the windows xp pcmia controller. Checking Dell's website, no specific drivers were listed for that either. General Search on the web indicates that multiple people face similar problems with their SD cards, yet none actually spell out the route issue that causes this. Please let me know if you have any suggestions for further debugging. Thanks in advance

    Read the article

  • Can I get the Waves Maxx speaker effects to work in Ubuntu?

    - by Rafael
    I have a new machine that comes with JBL 2.1 Speakers with Waves Maxx Audio 3. On Windows it sounds perfect, though in Ubuntu 12.04 I get cheap/sound with simple mp3 files. I have tried a few things on different blogs but no luck so far. Any ideas? aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: N700 [Logitech Speaker Lapdesk N700], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0

    Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >