Search Results

Search found 71021 results on 2841 pages for 'remote work'.

Page 90/2841 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• hp XW8000 work station power supply

  - by user281745

  My power supply went up in the XW8000 and I bought a new corsair cx500. I installed it but when I hook it up and I turn the computer on I get a beeping noise from the computer. I looked at the old power supply and the new power supply. The only difference is that the new power supply has 500 watts and the old one is 450 watts and the old PSU has a brown wire and the new power supply has 2 orange wires at the end. I found out that it is a sense wire that is in a different location so I was wondering how do I fix this problem.

  Read the article

• Wireless does not work anymore after software update with Ubuntu 12.10 on a Dell Latitude E6230

  - by Andy

  I just installed Ubuntu 12.10 on my DELL Latitude E6230, on first boot wifi worked properly but when I updated the software it stopped working. I can't figure out the problem... The wireless network controller is a Broadcom Corporation BCM4313 802.11b/g/n Wireless Lan Controller (rev 01) "lshw -class network" gives, for the above controller: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7d00000-f7d03fff After reading the answer to another similar question, I edited the file NetworkManager.conf to make "managed=true", but that did not make any difference, it is as if the wireless adapter were not there. In the "Network" setting window, I only see "Wired" and "Network proxy". Wireless has just disappeared: rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no and that's it! Nothing about the wireless controller... Any suggestions?

  Read the article

• Terminal Bell Doesn't Work

  - by JoBu1324

  I'd like to get the terminal bell playing through my speakers, but so far I haven't had any luck. I've tried the suggestions in this question as well as a number of other sources, but I haven't had any luck. I've also gone the route of un-blacklisting pcspkr in modprobe, but that only works for the beep command, not the terminal bell, echo -e '\a', ping -a, etc. I don't have a "PC Beep" option in alsamixer

  Read the article

• Setting APPMENU_DISPLAY_BOTH for gnome applications does not work on Ubuntu 12.04 LTS

  - by Jack'

  To start the application with the menu enabled in the application and the panel, the following command has to be used: APPMENU_DISPLAY_BOTH=1 appname I recently discovered that this only works for non-gnome applications on Ubuntu 12.04 LTS, i.e. if you replace appname with applications such as gnome-terminal, gedit, evince, empathy, evolution, rhythmbox, nautilus, etc. only global menus will be displayed. However, if you start, for example, gimp or inkscape by using APPMENU_DISPLAY_BOTH, both global and local menus will be shown. The questions is: why is APPMENU_DISPLAY_BOTH not taken into account when starting such gnome applications? P.S. I know how to disable global menus in order to get the local ones (UBUNTU_MENUPROXY trick, removing appmenu-gtk/qt packages, removing the indicator-appmenu, etc.) Thanks for the help!

  Read the article

• The upgrading service doesn`t work in South Korea

  - by Susung Park

  I am using Ubuntu, and I live in South Korea. I have installed the operating system about three months ago, so the current version in the computer is 11.04. I wanna upgrade this to the new version, and I tried some methods to do so. And when I started upgrading the computer, a message came up that it cannot download the update package because of the problem of internet connection. What should I do?

  Read the article

• Routing and Remote Access Port Mapping not applied to localhost

  - by Computer Guru

  Hi, I've set up Routing and Remote Access (Windows Server 2003) to forward publicip:80 to a server on the private internal network, and that's working great. Incoming requests from the internet to port 80 are correctly forwarded to our internal web server and everything is fine. However, requests on the server itself are not being forwarded. That is, if I open a console window and type "telnet publicip 80" from the server on publicip, the request is not forwarded to the private server. I understand that in RRAS I've mapped port 80 on the public interface to the private server and that's why it's not working; but I don't know how to configure it so that requests from the local PC are also forwarded to the private server. I'd appreciate any help or feedback on the matter. Thanks!

  Read the article

• Does 64-bit Ubuntu work on the Acer Aspire One D255

  - by hippietrail

  The Acer Aspire One D255 is the cheapest dual core netbook on the market right now. It has an Intel Atom N550 which should be able to run a 64-bit OS. But when I try to boot the Ubuntu 64-bit live CD I only get one line of diagnostic output that it "found something" on the USB CD drive before locking up. I haven't been able to find anything by Googling yet. Could it just be driver issues for this machine or could the platform be inherently frail for running 64-bit? (My machine is two days old on trial and Windows 7 and Ubuntu 32-bit run but it has locked up under casual use on both OSes.)

  Read the article

• Burg Custom Icons work only with specific themes

  - by el10780

  I have made a custom icon for burg loader for my Lenovo Recovery Partition.I have made 3 icons : large_qdrive.png (128 X 128 pixels) small_qdrive.png (24 X 24 pixels) grey_qdrive.png (128 x 128 pixels) The .png icons that I created I made them using gimp from a qdrive.ico file that I found in the Lenovo Recovery Partition. I transferred the icons to the /boot/burg/themes/icons folder and I added to the class list of the grey,large,small and the hover files the following lines : -qdrive { image = "$$/large_qdrive.png" } in the large file -qdrive { image = "$$/small_qdrive.png" } in the small file -qdrive { image = "$$/grey_qdrive.png" } in the grey file -qdrive { image = "$$/grey_qdrive.png:$$/large_qdrive.png" } in the hover file I ran sudo update-burg and after that I modified the following line in the burg.cfg file : menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { to menuentry "Windows 7 (loader) (on /dev/sda2)" --class qdrive --class os { and I also tried to change the title for the Lenovo Recovery Partition,so I tried this as well: menuentry "Lenovo Recovery Partition (on /dev/sda2)" --class qdrive --class os { None of this tries enforced actually burg loader to use the custom icon that I made and I can't figure out why. I have to mention also that there are a few themes that I have installed in burg which actually are able to use the small_qdrive.png icon that I made,but all the others which use either the large_qdrive.png or the grey_qdrive.png weren't able to use the custom icons. I have double checked for typos in all the files that I have created or I modified,so I am pretty sure that I haven't misspelled anything. I have checked also the title of the custom icons that I made and neither of them have a typo. I have looked also if there are any other folder that the themes might use to retrieve the icons,but it seems that all of them except for **Fortune** theme,which I downloaded from OMG!UBUNTU,use the icons folder which is located in /boot/burg/themes/icons I tried to add the custom icons to the icons folder of the theme **Fortune**,but still nothing happened.

  Read the article

• Reasons why crontab does not work

  - by Adam Matan

  Many a time and oft, crontab scripts are not executed as expected. There are numerous reasons for that, for example: wrong crontab notation, permissions, environment variables and many more. This community wiki aims to aggregate the top reasons for crontab scripts not being executed as expected. Write each reason in a separate answer. Please include one reason per answer - details about why it's not executed - and fix(es) for that one reason. Please write only cron-specific issues, e.g. commands that execute as expected from the shell but execute erroneously by cron.

  Read the article

• After upgrading to trusty, ALSA midi connection (aconnect) doesn't seem to work right

  - by SougonNaTakumi

  Previously in kubuntu 13.10 I was able to open vmpk or plug in a midi keyboard, and provided that TiMidity was running in server mode, I could run aconnect [keyboard port (129:0 for vmpk)] 14:0 aconnect 14:0 128:0 and I could play the keyboard and get sound. But now, a while after upgrading to trusty, I tried to do that, and didn't get any sound. TiMidity itself still plays files fine, but if I try to play them with aplaymidi, I still just get silence. Oddly, the midi files are clearly being read. When I ran (where 130:0 was vmpk's input port) aplaymidi -p 130:0 ~/path/to/midi.mid vmpk was highlighting notes on the piano as if it were playing the midi. One time I tried this, TiMidity (?) very briefly played a fraction of a second of the first chord of my song before everything went silent and vmpk just highlighted the first voice on the keyboard as usual. Now the weirdest part of this is that probably about 40% of the time, when I've played at least one note with either aplaymidi or vmpk, when I run aconnect -x I get a sudden burst of a note or chord from my speakers (that is, if I played one note, I get a note; if I played multiple sequential notes, they turn into a chord), as if the notes were being queued up but not being played and that somehow liberated them. I have no idea what's going on there. A little while ago I remember having a problem with Audacity playing wav files sped up and also locking up if I tried to pause it, which it stopped doing when I set the audio devices to the actual audio devices rather than pulse. But now when I checked again, it's doing the opposite: it won't play audio at all and/or acts weirdly if I don't set the audio devices to pulse, and either way will very occasionally randomly do the speeding up thing regardless. Oddly in the midst of what's looking like a pretty screwed up sound system, sound in VLC and Firefox has been working fine and if I play a wav file with aplay ~/path/to/sound.wav that works fine too. Any idea what I could do to figure out what's wrong with ALSA and/or fix it?

  Read the article

• Getting touchpad to work in desktop ubuntu

  - by kamziro

  I bought a small touchpad to stick on top of the keyboard, and it works fine on the windows computer, but not on my ubuntu desktop. I mean, when I do "xinput list" it shows the following: ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PIXART USB OPTICAL MOUSE id=8 [slave pointer (2)] ? ? Logitech USB-PS/2 Optical Mouse id=11 [slave pointer (2)] ? ? Microsoft Wired Keyboard 600 id=13 [slave pointer (2)] ? ? Macintosh mouse button emulation id=14 [slave pointer (2)] ? ? Cirque Corporation 9925 AG Touchpad id=15 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Power Button id=7 [slave keyboard (3)] ? No brand SP04-A1 id=9 [slave keyboard (3)] ? Elite Silicon USB Audio Device id=10 [slave keyboard (3)] ? Microsoft Wired Keyboard 600 id=12 [slave keyboard (3)] The Cirque Corporation touchpad (I'm assuming that's the component name) is the touchpad. Is there anything I'm missing?

  Read the article

• How to synchronize two folders on two remote Linux virtual machines

  - by Manoj Agarwal

  I have two virtual machines, Host OS is ESXi 3.5 and guest OS is Centos 4.6. There are two ESXi servers remotely located, each containing a Centos 4.6 virtual machine. I wish, whatever change I make in any file/folder in one virtual machine should be automatically synchronized on other remote virtual machine. The synchronization process should be automatic. It should only sync differentials, not simulate entire copy with overwrite operation. Sync should be intelligent enough to look for what has changed and what not, and should only update the changed files/folders. Further, there should be some sort of overview and selection for syncing, for example, if it shows 4 files have changed, It should be possible to sync only two files and leave other two for the time being. So, some intelligent syncing mechanism for Linux is needed.

  Read the article

• How does font rendering actually work?

  - by Andrea

  I realize that I know essentially nothing about the way fonts get rendered in my computer. From what I can observe, font rendering is generally made in a consistent way throughout the system. For instance, the subpixel font hinting settings that I configure in my DE control panel have influence on text which appears on window borders, in my browser, in my text editor and so on. (I should observe that some Java applications show a noticeable difference, so I guess they are using a different font rendering mechanism). What I get from the above is that probably all applications that need font rendering make use of some OS (or DE)-wide library. On the other hand, browsers usually manage their own rendering through a rendering engine, that takes care of positioning various items - including text - according to specific flow rules. I am not sure how these two facts are compatible. I would assume that the browser would have to ask the OS to draw a glyph at a given position, but how can it manage the flow of text without knowing beforehand how much space the glyph will take? Are there separate calls to determine the glyph sizes, so that the browser can manage the flow as if characters were little boxes that are later filled in by the OS? (Although this does not take care of kerning). Or is the OS responsible for drawing a whole text area, including text flow? Does the OS return the rendered glyph as a bitmap and leaves it to the application to draw that on the screen?

  Read the article

• Facebook integration in Empathy doesn't work in 12.10

  - by skerit

  The new web apps feature is fun, I've set up everything as it should be, but Empathy still doesn't connect to Facebook. When I go to the "Online-accounts" dialog and open the Empathy options dialog in the Facebook tab this shows up: Identification is blank and can't be edited Alias is blank, but can be edited A notification saying "Go online to edit your personal data" is visible I've tried logging into Facebook using my email address AND my username, both with the same results.

  Read the article

• gnome-file-share-properties doesn't work

  - by Riccardo Magrini

  I've configured gnome-file-share-properties on all my Ubuntu's PC for sharing the directory Public to each other. I following some guide found on Internet for the configuration of it, all explain the same procedure but in my case I don't see any Public directory shared with the PC. Following this link http://library.gnome.org/users/gnome-user-share/stable/gnome-user-share-getting-started.html.en I'd see the directory Public plus the name of PC that shares its directory on Nautilus Places. In my case I don't see anything, therefore on the Network place see all the machines 'n if I try to click on one receive this: "DBus error org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus)" note: I don't want to use Samba because I've all Ubuntu PC, and the firewall is disabled on all PC.

  Read the article

• Canon Multitasking printer: Scanner doesn't work, printer does

  - by Holger Böttcher

  Model: Canon Prixma MG2260 I have installed to ubuntu 14.04 Trusty Tahr. Now I have the problem by my multi function device. The printer works, but the scanner doesn't! I have downloaded the Linux software of Canon for the 2200 series. I have downloaded the software of the Internet site of Canon. 6 Zip folder 3 deb. and 3 rpm. Always 1 for computer, 1 for scanner, 1 for other Thinks. I can load them on my PC and unpacking, but they do not install themselves. Does any person know what I have to do about this?

  Read the article

• Which programming language suits a system that must work without user input

  - by Ruud

  I'm building a prototype of a device that will function much alike a digital photoframe. It will display images retrieved from the internet. The device must start up and run the photoframe. It will have no user interface. The device has a minimal ubuntu installation, but I could install Xorg or whatever needed. Question: I have trouble figuring out which programming language will be suitable. I've just started using Python to try out several things and I am able to download and display images. I guess that means Python can do what I'd like, but is it suitable as a language that will be run on boot without any user interference? Related questions: - How do I set up Linux to start that script automatically? - How to setup a second Python script as a server that runs in the background to retrieve images before they are displayed (Because I think I'll need threading of some sort?)

  Read the article

• xmonad keyboard doesn't work

  - by Mikkel Paulson

  I'm experimenting with xmonad, which I installed from the Ubuntu Software Centre on Ubuntu 12.10. It looks cool, but when I invoke it (using xmonad --replace from the command line) my title bars disappear and my keyboard stops working. At all. The terminal stops working, the keystrokes I've seen in online "getting started" guides are ignored, and the only way for me to actually power the system off is to hit the reset button or ssh in from my phone. Ironically, my mouse still works. One guide I saw suggested replacing the default window environment with xmonad, but I'm afraid of rendering my system completely inoperable if I do that. Any suggestions?

  Read the article

• Both Webmin & ISPConfig won't work on my Ubuntu Linode

  - by SERVE-U

  I followed the steps on this page to download and setup Webmin on my Linode Ubuntu server, however, when I try to visit https + my.ip.add.ress + :10000, the page just hangs and nothing loads. I already looked into my firewall settings. I uninstalled Webmin and installed ISPConfig and all its dependencies, and the same thing happens at https + my.ip.add.ress + :8080. This is my first time managing a server so there could be something I overlooked. But my server is a pretty vanilla Ubuntu 12.10 with LAMP stack installed exactly as per the instructions in Linode's documentation.

  Read the article

• Active Directory remote versus local computer logon

  - by Jake

  Hi, Hope some one can help a network/server noob understand how domains work in AD. I am in an organisation with 2 AD servers in 2 different countries, e.g. US and UK, and they set up the US and UK domains respectively. the accounts are set up such that all employees in both countries have a US\user and UK\user account. What is the difference if a UK user logon with US\user from a local UK computer, versus RDP (remote desktop) into a US server with US\user? Thanks for your help.

  Read the article

• Monitoring several remote servers over different VPNs

  - by Ciaran

  I'm a developer with about 20 different clients running our server application. I access each of the clients' servers remotely through VPN to provide support, updates, etc. Is there any tool available that I can set up locally that will connect through each of the VPNs automatically to allow me to monitor? The idea sounds very far fetched to me as the VPN software varies a good bit but maybe someone's had to do something similar before? It's been a few years since I last used Nagios but I think it'd be quite cool to have that set up pointing at each of the remote servers through VPN somehow.

  Read the article

• Will Ubuntu 11.04 work on my old pc?

  - by M4tic

  It has an old SiS based graphics chip with 64mb memory, there were never 3D drivers for them. Ubuntu 10.10 doesn't even boot on it and my laptop, a Lenovo N200 with intel 9something graphics 128mb so I'm really worried. Broadband prices don;t come cheap in South Africa so the download has to be worth it. I can wait for the shipment but I've since orderd 10.10 and it hasn't come, so I don't know if I'm barred from using that service since I've been sent a disc every release.

  Read the article

• This for array colllision function doesn't work with anything but first object in array

  - by Zee Bashew

  For some reason, this simple simple loop is totally broken. (characterSheet is my character Class, it's just a movieClip with some extra functionality) (hitBox, is basically a square movieclip) Anyway: every time hitBox make contact with a characterSheet in a different order than they were created: Nothing happens. The program only seems to be listening to collisions that are made with o2[0]. As soon as another hitBox is created, it pushes the last one out of o2[0] and the last one becomes totally useless. What's super weird is that I can hit characterSheets in any order I like.... public function collisions(o1:Array, o2:Array) { if((o1.lenght>=0)&&(o2.length>=0)){ for (var i = 0; i < o1.length; i++) { var ob1 = o1[i]; for (var f = 0; f < o1.length; f++) { var ob2 = o2[f]; if (ob1 is characterSheet) { if (ob2.hitTestObject(ob1)) { var right:Boolean = true; if (ob1.x < hitBox(ob2).origin.x) right = false; characterSheet(ob1).specialDamage(hitBox(ob2).damageType, hitBox(ob2).damage, right); }}}}}} Also it might be somewhat helpful to see the function for creating a new hitBox public function SpawnHitBox(targeted, following, atype, xoff, yoff, ... args) { var newHitBox = new hitBox(targeted, following, atype, xoff, yoff, args); badCollisionObjects.push(newHitBox); arraydictionary[newHitBox] = badCollisionObjects; addChild(newHitBox); }

  Read the article

• Unable to copy multiple files from remote sftp via ssh

  - by Kevin S

  I am trying to copy multiple (1000s) .JPG files from remote SFTP server to current server using mget command but it is not working. Here is the command that I used sftp [email protected] sftp> cd /images sftp> mget *.JPG Screenshot at http://i.stack.imgur.com/bSciQ.png Nothing happens so when I do CTRL + C it gives an error that says File "/images/*.JPG" not found. I have already referred all suggestions posted on the forum but nothing is working. Let me know if there is another way to copy.

  Read the article

• Bluetooth does not work xubuntu 12.04 (i386)

  - by user877329

  I cannot pair my bluetooth devices dell bt mouse and keyboard. Also I keep getting blueman-assistant crashed with AttributeError in next_page_fn(): FakeDevice instance has no attribute 'Services' Is this bug really fixed (I have installed all latest updates, but the bug page in launchpad https://bugs.launchpad.net/bugs/626839 cannot be displayed) 3.2.0-31-generic #50-Ubuntu SMP Fri Sep 7 16:17:36 UTC 2012 i686 i686 i386 GNU/Linux

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >