Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 90/600 | < Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >

• Static IP addressing issue in Ubuntu on BeagleBoneBlack Rev C

  - by Stringfellow

  I have my BBB configured to use a static IP address using the following in the file /etc/network/interfaces: allow-hotplug eth0 iface eth0 inet static address 192.168.0.1 netmask 255.255.255.0 network 192.168.0.0 This seems to work ok on boot, but when the ethernet cable is unplugged and then plugged back in, I lose the IP address. Any ideas what's going on here? Another weird symptom: If I boot the BBB with the network cable unplugged, but the switch it's plugged into off, I'll get my static IP. But, when I turn the switch on, I'll get a DHCP-assigned address. This is even though I have it configured with a static IP address. One last thing. If I ifdown etho, the interface will be gone when I do an ifconfig. If I wait a few seconds, though, and then re-run ifconfig, it will reappear, without an IP address. (Before I disabled IPv6, I used to get a IPv4 DHCP address in this case... weird). When that happens, I get a message like this in /var/log/messages: Apr 23 20:32:06 beaglebone kernel: [ 737.170172] libphy: 4a101000.mdio:00 - Link is Up - 100/Full Apr 23 20:32:06 beaglebone kernel: [ 737.170304] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Here's my uname -a: root@beaglebone:/etc# uname -a Linux beaglebone 3.8.13-bone47 #1 SMP Fri Apr 11 01:36:09 UTC 2014 armv7l GNU/Linux Any ideas what's going on here?

  Read the article

• How to disable caching in Rails by IP address?

  - by huacnlee

  I was used caches_page/caches_action for some page, it set expire in a time(1 hour or 1 day), I don't expire cache when the data updated. When the editors create or update the content them can't view the new result in the page. I want to disable the global caching when the visitor IP in my company. How to do it?

  Read the article

• How do I check if an email address is valid without sending anything to it?

  - by Charles

  I have a client with 5000 emails from an old list he has that he wants to promote his services to. He wants to know which emails on the list are still valid. I want to check them for him - without sending out 5K emails randomly and then being listed as a spammer or something. Ideas?

  Read the article

• How can I get GDB to tell me what address caused a segfault?

  - by nornagon

  I'd like to know if my program is accessing NULL pointers or stale memory.

  Read the article

• Does OpenCL allow concurrent writes to same memory address?

  - by Wonko

  Is two (or more) different threads allowed to write to the same memory location in global space in OpenCL? The write is always changing a uchar from 0 to 1 so the outcome should be predictable, but I'm getting erratic results in my program, so I'm wondering if the reason can be that some of the writes fail. Could it help to declare the buffer write-only and copy it to a read-only buffer afterwards?

  Read the article

• How to display everything that is sent to an email address on a website?

  - by dot

  I would like to display all the subjects of email received on a website. Is there an open source "pop to php" script? Or a service I can use directly? Any help is appreciated! thanks!

  Read the article

• how do you set a property of a control to an address of a function in xaml?

  - by ambog36

  Hi, I have a control that has a "Filter" property that expects a function that defines how the contents of the control should be filtered. so far i am setting the filter in code behind as such: MyControl.Filter = AddressOf Filters.MyFilter In this example MyFilter is a shared function in the Filters class with the following signature: Public Shared Function MyFilter(ByVal obj As Object, ByVal text As String) As Boolean I would like to set this in xaml. I was thinking of setting the Filters.MyFilter as a static resource and setting it that way: ...Filter="{StaticResource myFilter}"/ but i cant set Filters.MyFilter as a static resource. Any ideas on how to achieve this? Thanks,

  Read the article

• Is it standard C++ to set the value of a member pointer to the address of another member in the cons

  - by SilverSun

  Is this valid? class Foo { Bar m_bar; Bar * m_woo; public: Foo() : m_bar(42, 123), m_woo(&m_bar) { } };

  Read the article

• How to address thread-safety of service data used for maintaining static local variables in C++?

  - by sharptooth

  Consider the following scenario. We have a C++ function with a static local variable: void function() { static int variable = obtain(); //blahblablah } the function needs to be called from multiple threads concurrently, so we add a critical section to avoid concurrent access to the static local: void functionThreadSafe() { CriticalSectionLockClass lock( criticalSection ); static int variable = obtain(); //blahblablah } but will this be enough? I mean there's some magic that makes the variable being initialized no more than once. So there's some service data maintained by the runtime that indicates whether each static local has already been initialized. Will the critical section in the above code protect that service data as well? Is any extra protection required for this scenario?

  Read the article

• PHP: How do I find out if someone is from the US from his/her IP Address?

  - by lucha libre

  I don't want anything incredibly complicated. I am working on a client outside the US, and I just want a basic check to see if someone is accessing his page from the US or not. After that, I am going to default the language in either English or Spanish, after determining where the visitor is from. Thanks.

  Read the article

• Are there actually lag times to remove an email address from "the system"? [closed]

  - by Alex Gosselin

  For example, you send an unsubscribe message to a legitimate company or a spam, they reply that they will remove you and it may take up to 72 hours to take effect. I find it hard to believe anything that simple could take more than 3/4 of a second to take effect system wide. Another example would be when you call the visa activation line, there is a "delay" of several minutes while they try to sell you some kind of insurance. Usually just as you get the point across that you don't want it they will tell you your card has been activated and let you go. Are these delays real?

  Read the article

• Cannot determine why pointer variable will not address elements in a string in this program?

  - by Smith Will Suffice

  I am attempting to utilize a pointer variable to access elements of a string and there are issues with my code generating a compilation error: #include <stdio.h> #define MAX 29 char arrayI[250]; char *ptr; int main(void) { ptr = arrayI; puts("Enter string to arrayI: up to 29 chars:\n"); fgets(arrayI, MAX, stdin); printf("\n Now printing array by pointer:\n"); printf("%s", *ptr); ptr = arrayI[1]; //(I set the pointer to the second array char element) printf("%c", *ptr); //Here is where I was wanting to use my pointer to //point to individual array elements. return 0; } My compiler crieth: [Warning] assignment makes pointer from integer without a cast [enabled by default] I do not see where my pointer was ever assigned to the integer data type? Could someone please explain why my attempt to implement a pointer variable is failing? Thanks all!

  Read the article

• The dynamic Type in C# Simplifies COM Member Access from Visual FoxPro

  - by Rick Strahl

  I’ve written quite a bit about Visual FoxPro interoperating with .NET in the past both for ASP.NET interacting with Visual FoxPro COM objects as well as Visual FoxPro calling into .NET code via COM Interop. COM Interop with Visual FoxPro has a number of problems but one of them at least got a lot easier with the introduction of dynamic type support in .NET. One of the biggest problems with COM interop has been that it’s been really difficult to pass dynamic objects from FoxPro to .NET and get them properly typed. The only way that any strong typing can occur in .NET for FoxPro components is via COM type library exports of Visual FoxPro components. Due to limitations in Visual FoxPro’s type library support as well as the dynamic nature of the Visual FoxPro language where few things are or can be described in the form of a COM type library, a lot of useful interaction between FoxPro and .NET required the use of messy Reflection code in .NET. Reflection is .NET’s base interface to runtime type discovery and dynamic execution of code without requiring strong typing. In FoxPro terms it’s similar to EVALUATE() functionality albeit with a much more complex API and corresponiding syntax. The Reflection APIs are fairly powerful, but they are rather awkward to use and require a lot of code. Even with the creation of wrapper utility classes for common EVAL() style Reflection functionality dynamically access COM objects passed to .NET often is pretty tedious and ugly. Let’s look at a simple example. In the following code I use some FoxPro code to dynamically create an object in code and then pass this object to .NET. An alternative to this might also be to create a new object on the fly by using SCATTER NAME on a database record. How the object is created is inconsequential, other than the fact that it’s not defined as a COM object – it’s a pure FoxPro object that is passed to .NET. Here’s the code: *** Create .NET COM InstanceloNet = CREATEOBJECT('DotNetCom.DotNetComPublisher') *** Create a Customer Object Instance (factory method) loCustomer = GetCustomer() loCustomer.Name = "Rick Strahl" loCustomer.Company = "West Wind Technologies" loCustomer.creditLimit = 9999999999.99 loCustomer.Address.StreetAddress = "32 Kaiea Place" loCustomer.Address.Phone = "808 579-8342" loCustomer.Address.Email = "[email protected]" *** Pass Fox Object and echo back values ? loNet.PassRecordObject(loObject) RETURN FUNCTION GetCustomer LOCAL loCustomer, loAddress loCustomer = CREATEOBJECT("EMPTY") ADDPROPERTY(loCustomer,"Name","") ADDPROPERTY(loCustomer,"Company","") ADDPROPERTY(loCUstomer,"CreditLimit",0.00) ADDPROPERTY(loCustomer,"Entered",DATETIME()) loAddress = CREATEOBJECT("Empty") ADDPROPERTY(loAddress,"StreetAddress","") ADDPROPERTY(loAddress,"Phone","") ADDPROPERTY(loAddress,"Email","") ADDPROPERTY(loCustomer,"Address",loAddress) RETURN loCustomer ENDFUNC Now prior to .NET 4.0 you’d have to access this object passed to .NET via Reflection and the method code to do this would looks something like this in the .NET component: public string PassRecordObject(object FoxObject) { // *** using raw Reflection string Company = (string) FoxObject.GetType().InvokeMember( "Company", BindingFlags.GetProperty,null, FoxObject,null); // using the easier ComUtils wrappers string Name = (string) ComUtils.GetProperty(FoxObject,"Name"); // Getting Address object – then getting child properties object Address = ComUtils.GetProperty(FoxObject,"Address");    string Street = (string) ComUtils.GetProperty(FoxObject,"StreetAddress"); // using ComUtils 'Ex' functions you can use . Syntax     string StreetAddress = (string) ComUtils.GetPropertyEx(FoxObject,"AddressStreetAddress"); return Name + Environment.NewLine + Company + Environment.NewLine + StreetAddress + Environment.NewLine + " FOX"; } Note that the FoxObject is passed in as type object which has no specific type. Since the object doesn’t exist in .NET as a type signature the object is passed without any specific type information as plain non-descript object. To retrieve a property the Reflection APIs like Type.InvokeMember or Type.GetProperty().GetValue() etc. need to be used. I made this code a little simpler by using the Reflection Wrappers I mentioned earlier but even with those ComUtils calls the code is pretty ugly requiring passing the objects for each call and casting each element. Using .NET 4.0 Dynamic Typing makes this Code a lot cleaner Enter .NET 4.0 and the dynamic type. Replacing the input parameter to the .NET method from type object to dynamic makes the code to access the FoxPro component inside of .NET much more natural: public string PassRecordObjectDynamic(dynamic FoxObject) { // *** using raw Reflection string Company = FoxObject.Company; // *** using the easier ComUtils class string Name = FoxObject.Name; // *** using ComUtils 'ex' functions to use . Syntax string Address = FoxObject.Address.StreetAddress; return Name + Environment.NewLine + Company + Environment.NewLine + Address + Environment.NewLine + " FOX"; } As you can see the parameter is of type dynamic which as the name implies performs Reflection lookups and evaluation on the fly so all the Reflection code in the last example goes away. The code can use regular object ‘.’ syntax to reference each of the members of the object. You can access properties and call methods this way using natural object language. Also note that all the type casts that were required in the Reflection code go away – dynamic types like var can infer the type to cast to based on the target assignment. As long as the type can be inferred by the compiler at compile time (ie. the left side of the expression is strongly typed) no explicit casts are required. Note that although you get to use plain object syntax in the code above you don’t get Intellisense in Visual Studio because the type is dynamic and thus has no hard type definition in .NET . The above example calls a .NET Component from VFP, but it also works the other way around. Another frequent scenario is an .NET code calling into a FoxPro COM object that returns a dynamic result. Assume you have a FoxPro COM object returns a FoxPro Cursor Record as an object: DEFINE CLASS FoxData AS SESSION OlePublic cAppStartPath = "" FUNCTION INIT THIS.cAppStartPath = ADDBS( JustPath(Application.ServerName) ) SET PATH TO ( THIS.cAppStartpath ) ENDFUNC FUNCTION GetRecord(lnPk) LOCAL loCustomer SELECT * FROM tt_Cust WHERE pk = lnPk ; INTO CURSOR TCustomer IF _TALLY < 1 RETURN NULL ENDIF SCATTER NAME loCustomer MEMO RETURN loCustomer ENDFUNC ENDDEFINE If you call this from a .NET application you can now retrieve this data via COM Interop and cast the result as dynamic to simplify the data access of the dynamic FoxPro type that was created on the fly: int pk = 0; int.TryParse(Request.QueryString["id"],out pk); // Create Fox COM Object with Com Callable Wrapper FoxData foxData = new FoxData(); dynamic foxRecord = foxData.GetRecord(pk); string company = foxRecord.Company; DateTime entered = foxRecord.Entered; This code looks simple and natural as it should be – heck you could write code like this in days long gone by in scripting languages like ASP classic for example. Compared to the Reflection code that previously was necessary to run similar code this is much easier to write, understand and maintain. For COM interop and Visual FoxPro operation dynamic type support in .NET 4.0 is a huge improvement and certainly makes it much easier to deal with FoxPro code that calls into .NET. Regardless of whether you’re using COM for calling Visual FoxPro objects from .NET (ASP.NET calling a COM component and getting a dynamic result returned) or whether FoxPro code is calling into a .NET COM component from a FoxPro desktop application. At one point or another FoxPro likely ends up passing complex dynamic data to .NET and for this the dynamic typing makes coding much cleaner and more readable without having to create custom Reflection wrappers. As a bonus the dynamic runtime that underlies the dynamic type is fairly efficient in terms of making Reflection calls especially if members are repeatedly accessed. © Rick Strahl, West Wind Technologies, 2005-2010Posted in COM  FoxPro  .NET  CSharp  

  Read the article

• How to Reuse Your Old Wi-Fi Router as a Network Switch

  - by Jason Fitzpatrick

  Just because your old Wi-Fi router has been replaced by a newer model doesn’t mean it needs to gather dust in the closet. Read on as we show you how to take an old and underpowered Wi-Fi router and turn it into a respectable network switch (saving your $20 in the process). Image by mmgallan. Why Do I Want To Do This? Wi-Fi technology has changed significantly in the last ten years but Ethernet-based networking has changed very little. As such, a Wi-Fi router with 2006-era guts is lagging significantly behind current Wi-Fi router technology, but the Ethernet networking component of the device is just as useful as ever; aside from potentially being only 100Mbs instead of 1000Mbs capable (which for 99% of home applications is irrelevant) Ethernet is Ethernet. What does this matter to you, the consumer? It means that even though your old router doesn’t hack it for your Wi-Fi needs any longer the device is still a perfectly serviceable (and high quality) network switch. When do you need a network switch? Any time you want to share an Ethernet cable among multiple devices, you need a switch. For example, let’s say you have a single Ethernet wall jack behind your entertainment center. Unfortunately you have four devices that you want to link to your local network via hardline including your smart HDTV, DVR, Xbox, and a little Raspberry Pi running XBMC. Instead of spending $20-30 to purchase a brand new switch of comparable build quality to your old Wi-Fi router it makes financial sense (and is environmentally friendly) to invest five minutes of your time tweaking the settings on the old router to turn it from a Wi-Fi access point and routing tool into a network switch–perfect for dropping behind your entertainment center so that your DVR, Xbox, and media center computer can all share an Ethernet connection. What Do I Need? For this tutorial you’ll need a few things, all of which you likely have readily on hand or are free for download. To follow the basic portion of the tutorial, you’ll need the following: 1 Wi-Fi router with Ethernet ports 1 Computer with Ethernet jack 1 Ethernet cable For the advanced tutorial you’ll need all of those things, plus: 1 copy of DD-WRT firmware for your Wi-Fi router We’re conducting the experiment with a Linksys WRT54GL Wi-Fi router. The WRT54 series is one of the best selling Wi-Fi router series of all time and there’s a good chance a significant number of readers have one (or more) of them stuffed in an office closet. Even if you don’t have one of the WRT54 series routers, however, the principles we’re outlining here apply to all Wi-Fi routers; as long as your router administration panel allows the necessary changes you can follow right along with us. A quick note on the difference between the basic and advanced versions of this tutorial before we proceed. Your typical Wi-Fi router has 5 Ethernet ports on the back: 1 labeled “Internet”, “WAN”, or a variation thereof and intended to be connected to your DSL/Cable modem, and 4 labeled 1-4 intended to connect Ethernet devices like computers, printers, and game consoles directly to the Wi-Fi router. When you convert a Wi-Fi router to a switch, in most situations, you’ll lose two port as the “Internet” port cannot be used as a normal switch port and one of the switch ports becomes the input port for the Ethernet cable linking the switch to the main network. This means, referencing the diagram above, you’d lose the WAN port and LAN port 1, but retain LAN ports 2, 3, and 4 for use. If you only need to switch for 2-3 devices this may be satisfactory. However, for those of you that would prefer a more traditional switch setup where there is a dedicated WAN port and the rest of the ports are accessible, you’ll need to flash a third-party router firmware like the powerful DD-WRT onto your device. Doing so opens up the router to a greater degree of modification and allows you to assign the previously reserved WAN port to the switch, thus opening up LAN ports 1-4. Even if you don’t intend to use that extra port, DD-WRT offers you so many more options that it’s worth the extra few steps. Preparing Your Router for Life as a Switch Before we jump right in to shutting down the Wi-Fi functionality and repurposing your device as a network switch, there are a few important prep steps to attend to. First, you want to reset the router (if you just flashed a new firmware to your router, skip this step). Following the reset procedures for your particular router or go with what is known as the “Peacock Method” wherein you hold down the reset button for thirty seconds, unplug the router and wait (while still holding the reset button) for thirty seconds, and then plug it in while, again, continuing to hold down the rest button. Over the life of a router there are a variety of changes made, big and small, so it’s best to wipe them all back to the factory default before repurposing the router as a switch. Second, after resetting, we need to change the IP address of the device on the local network to an address which does not directly conflict with the new router. The typical default IP address for a home router is 192.168.1.1; if you ever need to get back into the administration panel of the router-turned-switch to check on things or make changes it will be a real hassle if the IP address of the device conflicts with the new home router. The simplest way to deal with this is to assign an address close to the actual router address but outside the range of addresses that your router will assign via the DHCP client; a good pick then is 192.168.1.2. Once the router is reset (or re-flashed) and has been assigned a new IP address, it’s time to configure it as a switch. Basic Router to Switch Configuration If you don’t want to (or need to) flash new firmware onto your device to open up that extra port, this is the section of the tutorial for you: we’ll cover how to take a stock router, our previously mentioned WRT54 series Linksys, and convert it to a switch. Hook the Wi-Fi router up to the network via one of the LAN ports (consider the WAN port as good as dead from this point forward, unless you start using the router in its traditional function again or later flash a more advanced firmware to the device, the port is officially retired at this point). Open the administration control panel via  web browser on a connected computer. Before we get started two things: first,  anything we don’t explicitly instruct you to change should be left in the default factory-reset setting as you find it, and two, change the settings in the order we list them as some settings can’t be changed after certain features are disabled. To start, let’s navigate to Setup ->Basic Setup. Here you need to change the following things: Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable Save with the “Save Settings” button and then navigate to Setup -> Advanced Routing: Operating Mode: Router This particular setting is very counterintuitive. The “Operating Mode” toggle tells the device whether or not it should enable the Network Address Translation (NAT)  feature. Because we’re turning a smart piece of networking hardware into a relatively dumb one, we don’t need this feature so we switch from Gateway mode (NAT on) to Router mode (NAT off). Our next stop is Wireless -> Basic Wireless Settings: Wireless SSID Broadcast: Disable Wireless Network Mode: Disabled After disabling the wireless we’re going to, again, do something counterintuitive. Navigate to Wireless -> Wireless Security and set the following parameters: Security Mode: WPA2 Personal WPA Algorithms: TKIP+AES WPA Shared Key: [select some random string of letters, numbers, and symbols like JF#d$di!Hdgio890] Now you may be asking yourself, why on Earth are we setting a rather secure Wi-Fi configuration on a Wi-Fi router we’re not going to use as a Wi-Fi node? On the off chance that something strange happens after, say, a power outage when your router-turned-switch cycles on and off a bunch of times and the Wi-Fi functionality is activated we don’t want to be running the Wi-Fi node wide open and granting unfettered access to your network. While the chances of this are next-to-nonexistent, it takes only a few seconds to apply the security measure so there’s little reason not to. Save your changes and navigate to Security ->Firewall. Uncheck everything but Filter Multicast Firewall Protect: Disable At this point you can save your changes again, review the changes you’ve made to ensure they all stuck, and then deploy your “new” switch wherever it is needed. Advanced Router to Switch Configuration For the advanced configuration, you’ll need a copy of DD-WRT installed on your router. Although doing so is an extra few steps, it gives you a lot more control over the process and liberates an extra port on the device. Hook the Wi-Fi router up to the network via one of the LAN ports (later you can switch the cable to the WAN port). Open the administration control panel via web browser on the connected computer. Navigate to the Setup -> Basic Setup tab to get started. In the Basic Setup tab, ensure the following settings are adjusted. The setting changes are not optional and are required to turn the Wi-Fi router into a switch. WAN Connection Type: Disabled Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable In addition to disabling the DHCP server, also uncheck all the DNSMasq boxes as the bottom of the DHCP sub-menu. If you want to activate the extra port (and why wouldn’t you), in the WAN port section: Assign WAN Port to Switch [X] At this point the router has become a switch and you have access to the WAN port so the LAN ports are all free. Since we’re already in the control panel, however, we might as well flip a few optional toggles that further lock down the switch and prevent something odd from happening. The optional settings are arranged via the menu you find them in. Remember to save your settings with the save button before moving onto a new tab. While still in the Setup -> Basic Setup menu, change the following: Gateway/Local DNS : [IP address of primary router, e.g. 192.168.1.1] NTP Client : Disable The next step is to turn off the radio completely (which not only kills the Wi-Fi but actually powers the physical radio chip off). Navigate to Wireless -> Advanced Settings -> Radio Time Restrictions: Radio Scheduling: Enable Select “Always Off” There’s no need to create a potential security problem by leaving the Wi-Fi radio on, the above toggle turns it completely off. Under Services -> Services: DNSMasq : Disable ttraff Daemon : Disable Under the Security -> Firewall tab, uncheck every box except “Filter Multicast”, as seen in the screenshot above, and then disable SPI Firewall. Once you’re done here save and move on to the Administration tab. Under Administration -> Management:  Info Site Password Protection : Enable Info Site MAC Masking : Disable CRON : Disable 802.1x : Disable Routing : Disable After this final round of tweaks, save and then apply your settings. Your router has now been, strategically, dumbed down enough to plod along as a very dependable little switch. Time to stuff it behind your desk or entertainment center and streamline your cabling.     

  Read the article

• Computer Networks UNISA - Chap 10 &ndash; In Depth TCP/IP Networking

  - by MarkPearl

  After reading this section you should be able to Understand methods of network design unique to TCP/IP networks, including subnetting, CIDR, and address translation Explain the differences between public and private TCP/IP networks Describe protocols used between mail clients and mail servers, including SMTP, POP3, and IMAP4 Employ multiple TCP/IP utilities for network discovery and troubleshooting Designing TCP/IP-Based Networks The following sections explain how network and host information in an IPv4 address can be manipulated to subdivide networks into smaller segments. Subnetting Subnetting separates a network into multiple logically defined segments, or subnets. Networks are commonly subnetted according to geographic locations, departmental boundaries, or technology types. A network administrator might separate traffic to accomplish the following… Enhance security Improve performance Simplify troubleshooting The challenges of Classful Addressing in IPv4 (No subnetting) The simplest type of IPv4 is known as classful addressing (which was the Class A, Class B & Class C network addresses). Classful addressing has the following limitations. Restriction in the number of usable IPv4 addresses (class C would be limited to 254 addresses) Difficult to separate traffic from various parts of a network Because of the above reasons, subnetting was introduced. IPv4 Subnet Masks Subnetting depends on the use of subnet masks to identify how a network is subdivided. A subnet mask indicates where network information is located in an IPv4 address. The 1 in a subnet mask indicates that corresponding bits in the IPv4 address contain network information (likewise 0 indicates the opposite) Each network class is associated with a default subnet mask… Class A = 255.0.0.0 Class B = 255.255.0.0 Class C = 255.255.255.0 An example of calculating  the network ID for a particular device with a subnet mask is shown below.. IP Address = 199.34.89.127 Subnet Mask = 255.255.255.0 Resultant Network ID = 199.34.89.0 IPv4 Subnetting Techniques Subnetting breaks the rules of classful IPv4 addressing. Read page 490 for a detailed explanation Calculating IPv4 Subnets Read page 491 – 494 for an explanation Important… Subnetting only applies to the devices internal to your network. Everything external looks at the class of the IP address instead of the subnet network ID. This way, traffic directed to your network externally still knows where to go, and once it has entered your internal network it can then be prioritized and segmented. CIDR (classless Interdomain Routing) CIDR is also known as classless routing or supernetting. In CIDR conventional network class distinctions do not exist, a subnet boundary can move to the left, therefore generating more usable IP addresses on your network. A subnet created by moving the subnet boundary to the left is known as a supernet. With CIDR also came new shorthand for denoting the position of subnet boundaries known as CIDR notation or slash notation. CIDR notation takes the form of the network ID followed by a forward slash (/) followed by the number of bits that are used for the extended network prefix. To take advantage of classless routing, your networks routers must be able to interpret IP addresses that don;t adhere to conventional network class parameters. Routers that rely on older routing protocols (i.e. RIP) are not capable of interpreting classless IP addresses. Internet Gateways Gateways are a combination of software and hardware that enable two different network segments to exchange data. A gateway facilitates communication between different networks or subnets. Because on device cannot send data directly to a device on another subnet, a gateway must intercede and hand off the information. Every device on a TCP/IP based network has a default gateway (a gateway that first interprets its outbound requests to other subnets, and then interprets its inbound requests from other subnets). The internet contains a vast number of routers and gateways. If each gateway had to track addressing information for every other gateway on the Internet, it would be overtaxed. Instead, each handles only a relatively small amount of addressing information, which it uses to forward data to another gateway that knows more about the data’s destination. The gateways that make up the internet backbone are called core gateways. Address Translation An organizations default gateway can also be used to “hide” the organizations internal IP addresses and keep them from being recognized on a public network. A public network is one that any user may access with little or no restrictions. On private networks, hiding IP addresses allows network managers more flexibility in assigning addresses. Clients behind a gateway may use any IP addressing scheme, regardless of whether it is recognized as legitimate by the Internet authorities but as soon as those devices need to go on the internet, they must have legitimate IP addresses to exchange data. When a clients transmission reaches the default gateway, the gateway opens the IP datagram and replaces the client’s private IP address with an Internet recognized IP address. This process is known as NAT (Network Address Translation). TCP/IP Mail Services All Internet mail services rely on the same principles of mail delivery, storage, and pickup, though they may use different types of software to accomplish these functions. Email servers and clients communicate through special TCP/IP application layer protocols. These protocols, all of which operate on a variety of operating systems are discussed below… SMTP (Simple Mail transfer Protocol) The protocol responsible for moving messages from one mail server to another over TCP/IP based networks. SMTP belongs to the application layer of the ODI model and relies on TCP as its transport protocol. Operates from port 25 on the SMTP server Simple sub-protocol, incapable of doing anything more than transporting mail or holding it in a queue MIME (Multipurpose Internet Mail Extensions) The standard message format specified by SMTP allows for lines that contain no more than 1000 ascii characters meaning if you relied solely on SMTP you would have very short messages and nothing like pictures included in an email. MIME us a standard for encoding and interpreting binary files, images, video, and non-ascii character sets within an email message. MIME identifies each element of a mail message according to content type. MIME does not replace SMTP but works in conjunction with it. Most modern email clients and servers support MIME POP (Post Office Protocol) POP is an application layer protocol used to retrieve messages from a mail server POP3 relies on TCP and operates over port 110 With POP3 mail is delivered and stored on a mail server until it is downloaded by a user Disadvantage of POP3 is that it typically does not allow users to save their messages on the server because of this IMAP is sometimes used IMAP (Internet Message Access Protocol) IMAP is a retrieval protocol that was developed as a more sophisticated alternative to POP3 The single biggest advantage IMAP4 has over POP3 is that users can store messages on the mail server, rather than having to continually download them Users can retrieve all or only a portion of any mail message Users can review their messages and delete them while the messages remain on the server Users can create sophisticated methods of organizing messages on the server Users can share a mailbox in a central location Disadvantages of IMAP are typically related to the fact that it requires more storage space on the server. Additional TCP/IP Utilities Nearly all TCP/IP utilities can be accessed from the command prompt on any type of server or client running TCP/IP. The syntaxt may differ depending on the OS of the client. Below is a list of additional TCP/IP utilities – research their use on your own! Ipconfig (Windows) & Ifconfig (Linux) Netstat Nbtstat Hostname, Host & Nslookup Dig (Linux) Whois (Linux) Traceroute (Tracert) Mtr (my traceroute) Route

  Read the article

• use svcutil to map multiple namespaces for generating wcf service proxies

  - by Pratik

  I want to use svcutil to map multiple wsdl namespace to clr namespace when generating service proxies. I use strong versioning of namespaces and hence the generated clr namespaces are awkward and may mean many client side code changes if the wsdl/xsd namespace version changes. A code example would be better to show what I want. // Service code namespace TestService.StoreService { [DataContract(Namespace = "http://mydomain.com/xsd/Model/Store/2009/07/01")] public class Address { [DataMember(IsRequired = true, Order = 0)] public string street { get; set; } } [ServiceContract(Namespace = "http://mydomain.com/wsdl/StoreService-v1.0")] public interface IStoreService { [OperationContract] List<Customer> GetAllCustomersForStore(int storeId); [OperationContract] Address GetStoreAddress(int storeId); } public class StoreService : IStoreService { public List<Customer> GetAllCustomersForStore(int storeId) { throw new NotImplementedException(); } public Address GetStoreAddress(int storeId) { throw new NotImplementedException(); } } } namespace TestService.CustomerService { [DataContract(Namespace = "http://mydomain.com/xsd/Model/Customer/2009/07/01")] public class Address { [DataMember(IsRequired = true, Order = 0)] public string city { get; set; } } [ServiceContract(Namespace = "http://mydomain.com/wsdl/CustomerService-v1.0")] public interface ICustomerService { [OperationContract] Customer GetCustomer(int customerId); [OperationContract] Address GetStoreAddress(int customerId); } public class CustomerService : ICustomerService { public Customer GetCustomer(int customerId) { throw new NotImplementedException(); } public Address GetStoreAddress(int customerId) { throw new NotImplementedException(); } } } namespace TestService.Shared { [DataContract(Namespace = "http://mydomain.com/xsd/Model/Shared/2009/07/01")] public class Customer { [DataMember(IsRequired = true, Order = 0)] public int CustomerId { get; set; } [DataMember(IsRequired = true, Order = 1)] public string FirstName { get; set; } } } 1. svcutil - without namespace mapping svcutil.exe /t:metadata TestSvcUtil\bin\debug\TestService.CustomerService.dll TestSvcUtil\bin\debug\TestService.StoreService.dll svcutil.exe /t:code *.wsdl *.xsd /o:TestClient\WebServiceProxy.cs The generated proxy looks like namespace mydomain.com.xsd.Model.Shared._2009._07._011 { public partial class Customer{} } namespace mydomain.com.xsd.Model.Customer._2009._07._011 { public partial class Address{} } namespace mydomain.com.xsd.Model.Store._2009._07._011 { public partial class Address{} } The client classes are out of any namespaces. Any change to xsd namespace would imply changing all using statements in my client code all build will break. 2. svcutil - with wildcard namespace mapping svcutil.exe /t:metadata TestSvcUtil\bin\debug\TestService.CustomerService.dll TestSvcUtil\bin\debug\TestService.StoreService.dll svcutil.exe /t:code *.wsdl *.xsd /n:*,MyDomain.ServiceProxy /o:TestClient\WebServicesProxy2.cs The generated proxy looks like namespace MyDomain.ServiceProxy { public partial class Customer{} public partial class Address{} public partial class Address1{} public partial class CustomerServiceClient{} public partial class StoreServiceClient{} } Notice that svcutil has automatically changed one of the Address class to Address1. I don't like this. All client classes are also inside the same namespace. What I want Something like this: svcutil.exe /t:code *.wsdl *.xsd /n:"http://mydomain.com/xsd/Model/Shared/2009/07/01, MyDomain.Model.Shared;http://mydomain.com/xsd/Model/Customer/2009/07/01, MyDomain.Model.Customer;http://mydomain.com/wsdl/CustomerService-v1.0, MyDomain.CustomerServiceProxy;http://mydomain.com/xsd/Model/Store/2009/07/01, MyDomain.Model.Store;http://mydomain.com/wsdl/StoreService-v1.0, MyDomain.StoreServiceProxy" /o:TestClient\WebServiceProxy3.cs This way I can logically group the clr namespace and any change to wsdl/xsd namespace is handled in the proxy generation only without affecting the rest of the client side code. Now this is not possible. The svcutil allows to map only one or all namespaces, not a list of mappings. I can do one mapping as shown below but not multiple svcutil.exe /t:code *.wsdl *.xsd /n:"http://mydomain.com/xsd/Model/Store/2009/07/01, MyDomain.Model.Address" /o:TestClient\WebServiceProxy4.cs But is there any solution. Svcutil is not magic, it is written in .Net and programatically generating the proxies. Has anyone written an alternate to svcutil or point me to directions so that I can write one.

  Read the article

• Slow NFS and GFS2 performance

  - by Tiago

  Recently I've designed and configured a 4 node cluster for a webapp that does lots of file handling. The cluster have been broken down into 2 main roles, webserver and storage. Each role is replicated to a second server using drbd in active/passive mode. The webserver does a NFS mount of the data directory of the storage server and the latter also has a webserver running to serve files to browser clients. In the storage servers I've created a GFS2 FS to hold the data which is wired to drbd. I've chose GFS2 mainly because the announced performance and also because the volume size which has to be pretty high. Since we entered production I've been facing two problems that I think are deeply connected. First of all, the NFS mount on the webservers keeps hanging for a minute or so and then resumes normal operations. By analyzing the logs I've found out that NFS stops answering for a while and outputs the following log lines: Oct 15 18:15:42 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:44 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:46 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:47 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:47 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:47 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:48 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:48 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:51 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:52 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:52 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:55 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:55 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:58 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK In this case, the hang lasted for 16 seconds but sometimes it takes 1 or 2 minutes to resume normal operations. My first guess was this was happening due to heavy load of the NFS mount and that by increasing RPCNFSDCOUNT to a higher value, this would become stable. I've increased it several times and apparently, after a while, the logs started appearing less times. The value is now on 32. After further investigating the issue, I've came across a different hang, despite the NFS messages still appear in the logs. Sometimes, the GFS2 FS simply hangs which causes both the NFS and the storage webserver to serve files. Both stay hang for a while and then they resume normal operations. This hangs leaves no trace on client side (also leaves no NFS ... not responding messages) and, on the storage side, the log system appears to be empty, even though the rsyslogd is running. The nodes connect themselves through a 10Gbps non-dedicated connection but I don't think this is an issue because the GFS2 hang is confirmed but connecting directly to the active storage server. I've been trying to solve this for a while now and I've tried different NFS configuration options, before I've found out the GFS2 FS is also hanging. The NFS mount is exported as such: /srv/data/ <ip_address>(rw,async,no_root_squash,no_all_squash,fsid=25) And the NFS client mounts with: mount -o "async,hard,intr,wsize=8192,rsize=8192" active.storage.vlan:/srv/data /srv/data After some tests, these were the configurations that yielded more performance to the cluster. I am desperate to find a solution for this as the cluster is already in production mode and I need to fix this so that this hangs won't happen in the future and I don't really know for sure what and how I should be benchmarking. What I can tell is that this is happening due to heavy loads as I have tested the cluster earlier and this problems weren't happening at all. Please tell me if you need me to provide configuration details of the cluster, and which do you want me to post. As last resort I can migrate the files to a different FS but I need some solid pointers on whether this will solve this problems as the volume size is extremely large at this point. The servers are being hosted by a third-party enterprise and I don't have physical access to them. Best regards. EDIT 1: The servers are physical servers and their specs are: Webservers: Intel Bi Xeon E5606 2x4 2.13GHz 24GB DDR3 Intel SSD 320 2 x 120GB Raid 1 Storage: Intel i5 3550 3.3GHz 16GB DDR3 12 x 2TB SATA Initially there was a VRack setup between the servers but we've upgraded one of the storage servers to have more RAM and it wasn't inside the VRack. They connect through a shared 10Gbps connection between them. Please note that it is the same connection that is used for public access. They use a single IP (using IP Failover) to connect between them and to allow for a graceful failover. NFS is therefore over a public connection and not under any private network (it was before the upgrade, were the problem still existed). The firewall was configured and tested thoroughly but I disabled it for a while to see if the problem still occurred, and it did. From my knowledge the hosting provider isn't blocking or limiting the connection between either the servers and the public domain (at least under a given bandwidth consumption threshold that hasn't been reached yet). Hope this helps figuring out the problem. EDIT 2: Relevant software versions: CentOS 2.6.32-279.9.1.el6.x86_64 nfs-utils-1.2.3-26.el6.x86_64 nfs-utils-lib-1.1.5-4.el6.x86_64 gfs2-utils-3.0.12.1-32.el6_3.1.x86_64 kmod-drbd84-8.4.2-1.el6_3.elrepo.x86_64 drbd84-utils-8.4.2-1.el6.elrepo.x86_64 DRBD configuration on storage servers: #/etc/drbd.d/storage.res resource storage { protocol C; on <server1 fqdn> { device /dev/drbd0; disk /dev/vg_storage/LV_replicated; address <server1 ip>:7788; meta-disk internal; } on <server2 fqdn> { device /dev/drbd0; disk /dev/vg_storage/LV_replicated; address <server2 ip>:7788; meta-disk internal; } } NFS Configuration in storage servers: #/etc/sysconfig/nfs RPCNFSDCOUNT=32 STATD_PORT=10002 STATD_OUTGOING_PORT=10003 MOUNTD_PORT=10004 RQUOTAD_PORT=10005 LOCKD_UDPPORT=30001 LOCKD_TCPPORT=30001 (can there be any conflict in using the same port for both LOCKD_UDPPORT and LOCKD_TCPPORT?) GFS2 configuration: # gfs2_tool gettune <mountpoint> incore_log_blocks = 1024 log_flush_secs = 60 quota_warn_period = 10 quota_quantum = 60 max_readahead = 262144 complain_secs = 10 statfs_slow = 0 quota_simul_sync = 64 statfs_quantum = 30 quota_scale = 1.0000 (1, 1) new_files_jdata = 0 Storage network environment: eth0 Link encap:Ethernet HWaddr <mac address> inet addr:<ip address> Bcast:<bcast address> Mask:<ip mask> inet6 addr: <ip address> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:957025127 errors:0 dropped:0 overruns:0 frame:0 TX packets:1473338731 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2630984979622 (2.3 TiB) TX bytes:1648430431523 (1.4 TiB) eth0:0 Link encap:Ethernet HWaddr <mac address> inet addr:<ip failover address> Bcast:<bcast address> Mask:<ip mask> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 The IP addresses are statically assigned with the given network configurations: DEVICE="eth0" BOOTPROTO="static" HWADDR=<mac address> ONBOOT="yes" TYPE="Ethernet" IPADDR=<ip address> NETMASK=<net mask> and DEVICE="eth0:0" BOOTPROTO="static" HWADDR=<mac address> IPADDR=<ip failover> NETMASK=<net mask> ONBOOT="yes" BROADCAST=<bcast address> Hosts file to allow for a graceful NFS failover in conjunction with NFS option fsid=25 set on both storage servers: #/etc/hosts <storage ip failover address> active.storage.vlan <webserver ip failover address> active.service.vlan As you can see, packet errors are down to 0. I've also ran ping for a long time without any packet loss. MTU size is the normal 1500. As there is no VLan by now, this is the MTU used to communicate between servers. The webservers' network environment is similar. One thing I forgot to mention is that the storage servers handle ~200GB of new files each day through the NFS connection, which is a key point for me to think this is some kind of heavy load problem with either NFS or GFS2. If you need further configuration details please tell me. EDIT 3: Earlier today we had a major filesystem crash on the storage server. I couldn't get the details of the crash right away because the server stop responding. After the reboot, I noticed the filesystem was extremely slow, and I was not being able to serve a single file through either NFS or httpd, perhaps due to cache warming or so. Nevertheless, I've been monitoring the server closely and the following error came up in dmesg. The source of the problem is clearly GFS, which is waiting for a lock and ends up starving after a while. INFO: task nfsd:3029 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. nfsd D 0000000000000000 0 3029 2 0x00000080 ffff8803814f79e0 0000000000000046 0000000000000000 ffffffff8109213f ffff880434c5e148 ffff880624508d88 ffff8803814f7960 ffffffffa037253f ffff8803815c1098 ffff8803814f7fd8 000000000000fb88 ffff8803815c1098 Call Trace: [<ffffffff8109213f>] ? wake_up_bit+0x2f/0x40 [<ffffffffa037253f>] ? gfs2_holder_wake+0x1f/0x30 [gfs2] [<ffffffff814ff42e>] __mutex_lock_slowpath+0x13e/0x180 [<ffffffff814ff2cb>] mutex_lock+0x2b/0x50 [<ffffffffa0379f21>] gfs2_log_reserve+0x51/0x190 [gfs2] [<ffffffffa0390da2>] gfs2_trans_begin+0x112/0x1d0 [gfs2] [<ffffffffa0369b05>] ? gfs2_dir_check+0x35/0xe0 [gfs2] [<ffffffffa0377943>] gfs2_createi+0x1a3/0xaa0 [gfs2] [<ffffffff8121aab1>] ? avc_has_perm+0x71/0x90 [<ffffffffa0383d1e>] gfs2_create+0x7e/0x1a0 [gfs2] [<ffffffffa037783f>] ? gfs2_createi+0x9f/0xaa0 [gfs2] [<ffffffff81188cf4>] vfs_create+0xb4/0xe0 [<ffffffffa04217d6>] nfsd_create_v3+0x366/0x4c0 [nfsd] [<ffffffffa0429703>] nfsd3_proc_create+0x123/0x1b0 [nfsd] [<ffffffffa041a43e>] nfsd_dispatch+0xfe/0x240 [nfsd] [<ffffffffa025a5d4>] svc_process_common+0x344/0x640 [sunrpc] [<ffffffff810602a0>] ? default_wake_function+0x0/0x20 [<ffffffffa025ac10>] svc_process+0x110/0x160 [sunrpc] [<ffffffffa041ab62>] nfsd+0xc2/0x160 [nfsd] [<ffffffffa041aaa0>] ? nfsd+0x0/0x160 [nfsd] [<ffffffff81091de6>] kthread+0x96/0xa0 [<ffffffff8100c14a>] child_rip+0xa/0x20 [<ffffffff81091d50>] ? kthread+0x0/0xa0 [<ffffffff8100c140>] ? child_rip+0x0/0x20

  Read the article

• Wireless Connected But No Internet Connection (Ubuntu 12.04)

  - by Zxy

  I am using same network for 2 days and everything was normal. However, today even though it shows me as connected to the network, I do not have internet connection. If I use ethernet cable instead of wireless, I am still able to connect to the internet. Also my friends are able to connect to the wireless network and they can get internet connection. I did not update or install anything since yesterday. Therefore I do not have any idea why it is happening. Here is some information about my connection: I will be appreciate to any kind of help. root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 hid 77367 2 hid_logitech_dj,usbhid ideapad_laptop 17890 0 sparse_keymap 13658 2 acer_wmi,ideapad_laptop lib80211_crypt_tkip 17275 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event wl 2646601 0 wmi 18744 1 acer_wmi i915 414672 3 drm_kms_helper 45466 1 i915 snd_timer 28931 2 snd_pcm,snd_seq mac_hid 13077 0 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq lib80211 14040 2 lib80211_crypt_tkip,wl drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 snd 62064 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_se q,snd_timer,snd_seq_device video 19068 1 i915 mei 36570 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp atl1c 36718 0 root@ghostrider:/etc/resolvconf# nm-tool NetworkManager Tool State: connected (global) - Device: eth1 [PoliTekno] ---------------------------------------------------- Type: 802.11 WiFi Driver: wl State: connected Default: yes HW Address: AC:81:12:7F:6B:B2 Capabilities: Speed: 54 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) CnDStudios: Infra, 00:12:BF:3F:0A:8A, Freq 2412 MHz, Rate 54 Mb/s, Strength 85 WPA AIR_TIES: Infra, 00:1C:A8:6E:84:32, Freq 2462 MHz, Rate 54 Mb/s, Strength 72 WPA2 VKSS: Infra, 00:E0:4D:01:0D:47, Freq 2452 MHz, Rate 54 Mb/s, Strength 62 WPA2 PROGEDA: Infra, 00:1A:2A:60:BF:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 47 WPA MobilAtolye: Infra, 72:2B:C1:65:75:3C, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 AIRTIES_WAR-141: Infra, 00:1C:A8:AB:AA:48, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 tilda_biri_yeni: Infra, 54:E6:FC:B0:3C:E9, Freq 2437 MHz, Rate 0 Mb/s, Strength 34 WEP *PoliTekno: Infra, 00:16:E3:40:C3:E4, Freq 2462 MHz, Rate 54 Mb/s, Strength 100 WPA2 AIRTIES_RJY: Infra, 00:1A:2A:BD:85:16, Freq 2462 MHz, Rate 54 Mb/s, Strength 55 WEP IPv4 Settings: Address: 0.0.0.0 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: F0:DE:F1:6C:90:65 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off root@ghostrider:/etc/resolvconf# sudo iwlist scan lo Interface doesn't support scanning. eth1 Scan completed : Cell 01 - Address: 00:16:E3:40:C3:E4 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-48 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: 00:E0:4D:01:0D:47 ESSID:"VKSS" Mode:Managed Frequency:2.452 GHz (Channel 9) Quality:4/5 Signal level:-64 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Cell 03 - Address: 00:1C:A8:AB:AA:48 ESSID:"AIRTIES_WAR-141" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-77 dBm Noise level:-95 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DDB20050F204104A0001101049001E007FC5100018DE7CF0D8B70223A62711C18926AC290E30303030303139631044000102103B0001031047001076B31BC241E953CB99C3872554425A28102100194169725469657320576972656C657373204E6574776F726B73102300074169723534343010240008312E322E302E31321042000F4154303939313131383030323832351054000800060050F20400011011000741697235343430100800020084103C000103 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 04 - Address: 72:2B:C1:65:75:3C ESSID:"MobilAtolye" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-78 dBm Noise level:-92 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DDA20050F204104A0001101044000102103B00010310470010BC329E001DD811B28601722BC165753C1021001D48756177656920546563686E6F6C6F6769657320436F2E2C204C74642E1023001C48756177656920576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F204000110110009487561776569415053100800020084103C000100 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s 24 Mb/s; 48 Mb/s Cell 05 - Address: 00:12:BF:3F:0A:8A ESSID:"CnDStudios" Mode:Managed Frequency:2.412 GHz (Channel 1) Quality:5/5 Signal level:-47 dBm Noise level:-95 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 06 - Address: 00:1C:A8:6E:84:32 ESSID:"AIR_TIES" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-56 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 07 - Address: 54:E6:FC:B0:3C:E9 ESSID:"tilda_biri_yeni" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-85 dBm Noise level:-99 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Cell 08 - Address: 18:28:61:16:57:C3 ESSID:"obilet" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-88 dBm Noise level:-99 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 09 - Address: 00:1A:2A:60:BF:61 ESSID:"PROGEDA" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-75 dBm Noise level:-98 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s eth0 Interface doesn't support scanning.

  Read the article

• 12c - flashforward, flashback or see it as of now...

  - by noreply(at)blogger.com (Thomas Kyte)

  Oracle 9i exposed flashback query to developers for the first time.  The ability to flashback query dates back to version 4 however (it just wasn't exposed).  Every time you run a query in Oracle it is in fact a flashback query - it is what multi-versioning is all about.However, there was never a flashforward query (well, ok, the workspace manager has this capability - but with lots of extra baggage).  We've never been able to ask a table "what will you look like tomorrow" - but now we do.The capability is called Temporal Validity.  If you have a table with data that is effective dated - has a "start date" and "end date" column in it - we can now query it using flashback query like syntax.  The twist is - the date we "flashback" to can be in the future.  It works by rewriting the query to transparently the necessary where clause and filter out the right rows for the right period of time - and since you can have records whose start date is in the future - you can query a table and see what it would look like at some future time.Here is a quick example, we'll start with a table:ops$tkyte%ORA12CR1> create table addresses  2  ( empno       number,  3    addr_data   varchar2(30),  4    start_date  date,  5    end_date    date,  6    period for valid(start_date,end_date)  7  )  8  /Table created.the new bit is on line 6 (it can be altered into an existing table - so any table  you have with a start/end date column will be a candidate).  The keyword is PERIOD, valid is an identifier I chose - it could have been foobar, valid just sounds nice in the query later.  You identify the columns in your table - or we can create them for you if they don't exist.  Then you just create some data:ops$tkyte%ORA12CR1> insert into addresses (empno, addr_data, start_date, end_date )  2  values ( 1234, '123 Main Street', trunc(sysdate-5), trunc(sysdate-2) );1 row created.ops$tkyte%ORA12CR1>ops$tkyte%ORA12CR1> insert into addresses (empno, addr_data, start_date, end_date )  2  values ( 1234, '456 Fleet Street', trunc(sysdate-1), trunc(sysdate+1) );1 row created.ops$tkyte%ORA12CR1>ops$tkyte%ORA12CR1> insert into addresses (empno, addr_data, start_date, end_date )  2  values ( 1234, '789 1st Ave', trunc(sysdate+2), null );1 row created.and you can either see all of the data:ops$tkyte%ORA12CR1> select * from addresses;     EMPNO ADDR_DATA                      START_DAT END_DATE---------- ------------------------------ --------- ---------      1234 123 Main Street                27-JUN-13 30-JUN-13      1234 456 Fleet Street               01-JUL-13 03-JUL-13      1234 789 1st Ave                    04-JUL-13or query "as of" some point in time - as  you can see in the predicate section - it is just doing a query rewrite to automate the "where" filters:ops$tkyte%ORA12CR1> select * from addresses as of period for valid sysdate-3;     EMPNO ADDR_DATA                      START_DAT END_DATE---------- ------------------------------ --------- ---------      1234 123 Main Street                27-JUN-13 30-JUN-13ops$tkyte%ORA12CR1> @planops$tkyte%ORA12CR1> select * from table(dbms_xplan.display_cursor);PLAN_TABLE_OUTPUT-------------------------------------------------------------------------------SQL_ID  cthtvvm0dxvva, child number 0-------------------------------------select * from addresses as of period for valid sysdate-3Plan hash value: 3184888728-------------------------------------------------------------------------------| Id  | Operation         | Name      | Rows  | Bytes | Cost (%CPU)| Time     |-------------------------------------------------------------------------------|   0 | SELECT STATEMENT  |           |       |       |     3 (100)|          ||*  1 |  TABLE ACCESS FULL| ADDRESSES |     1 |    48 |     3   (0)| 00:00:01 |-------------------------------------------------------------------------------Predicate Information (identified by operation id):---------------------------------------------------   1 - filter((("T"."START_DATE" IS NULL OR              "T"."START_DATE"<=SYSDATE@!-3) AND ("T"."END_DATE" IS NULL OR              "T"."END_DATE">SYSDATE@!-3)))Note-----   - dynamic statistics used: dynamic sampling (level=2)24 rows selected.ops$tkyte%ORA12CR1> select * from addresses as of period for valid sysdate;     EMPNO ADDR_DATA                      START_DAT END_DATE---------- ------------------------------ --------- ---------      1234 456 Fleet Street               01-JUL-13 03-JUL-13ops$tkyte%ORA12CR1> @planops$tkyte%ORA12CR1> select * from table(dbms_xplan.display_cursor);PLAN_TABLE_OUTPUT-------------------------------------------------------------------------------SQL_ID  26ubyhw9hgk7z, child number 0-------------------------------------select * from addresses as of period for valid sysdatePlan hash value: 3184888728-------------------------------------------------------------------------------| Id  | Operation         | Name      | Rows  | Bytes | Cost (%CPU)| Time     |-------------------------------------------------------------------------------|   0 | SELECT STATEMENT  |           |       |       |     3 (100)|          ||*  1 |  TABLE ACCESS FULL| ADDRESSES |     1 |    48 |     3   (0)| 00:00:01 |-------------------------------------------------------------------------------Predicate Information (identified by operation id):---------------------------------------------------   1 - filter((("T"."START_DATE" IS NULL OR              "T"."START_DATE"<=SYSDATE@!) AND ("T"."END_DATE" IS NULL OR              "T"."END_DATE">SYSDATE@!)))Note-----   - dynamic statistics used: dynamic sampling (level=2)24 rows selected.ops$tkyte%ORA12CR1> select * from addresses as of period for valid sysdate+3;     EMPNO ADDR_DATA                      START_DAT END_DATE---------- ------------------------------ --------- ---------      1234 789 1st Ave                    04-JUL-13ops$tkyte%ORA12CR1> @planops$tkyte%ORA12CR1> select * from table(dbms_xplan.display_cursor);PLAN_TABLE_OUTPUT-------------------------------------------------------------------------------SQL_ID  36bq7shnhc888, child number 0-------------------------------------select * from addresses as of period for valid sysdate+3Plan hash value: 3184888728-------------------------------------------------------------------------------| Id  | Operation         | Name      | Rows  | Bytes | Cost (%CPU)| Time     |-------------------------------------------------------------------------------|   0 | SELECT STATEMENT  |           |       |       |     3 (100)|          ||*  1 |  TABLE ACCESS FULL| ADDRESSES |     1 |    48 |     3   (0)| 00:00:01 |-------------------------------------------------------------------------------Predicate Information (identified by operation id):---------------------------------------------------   1 - filter((("T"."START_DATE" IS NULL OR              "T"."START_DATE"<=SYSDATE@!+3) AND ("T"."END_DATE" IS NULL OR              "T"."END_DATE">SYSDATE@!+3)))Note-----   - dynamic statistics used: dynamic sampling (level=2)24 rows selected.All in all a nice, easy way to query effective dated information as of a point in time without a complex where clause.  You need to maintain the data - it isn't that a delete will turn into an update the end dates a record or anything - but if you have tables with start/end dates, this will make it much easier to query them.

  Read the article

• What does DetourAttach(&(PVOID &)BindKeyT, BindKeyD); mean? Attaching a detour to a memory address..

  - by user288546

  Hello everyone! This is just a simple question. I've been reading the source of something which attaches to a memory address of a subroutine using DetourAttach(&(PVOID &)BindKeyT, BindKeyD); where BindKeyT is the address to a subroutine in memory. I'm curious, what exactly does (&(PVOID &) mean in english? I understand that PVOID is a void pointer, but how does this get translated into a function which can be used to attach a detour to?

  Read the article

• httpd dead but subsys locked

  - by McShark

  Hello, I modified today max_execution_time in php.ini, when I restarted the server, I get this error : Stopping httpd: [FAILED] Starting httpd: (98)Address already in use: make_sock: could not bind to address [::]:80 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs I killed httpd proc : killall httpd, and started it fine, but the I can't open any web site on the server. service httpd status OUTPUT : httpd dead but subsys locked I removed httpd file from /var/lock/subsys/ :S Same problem. Please Help!

  Read the article

• Layer 3 switch routing

  - by Yoshiwaan

  I need help moving over to using our layer 3 switch as the inter vlan routing device rather than our cisco router. I've mostly got it working but I've got stuck near the end and need some advice (I think I just need a bit of education on the subject really). Cur I have a Dell PowerConnect 7048 connecting to a Cisco 1841 router. I've got a few key excerpts from the configs to provide the key information. On the powerconnect I have the following: ip routing ip default-gateway 172.31.14.1 ip route 0.0.0.0 0.0.0.0 172.31.14.1 253 ! interface vlan 1 ip address 172.31.14.254 255.255.255.0 exit interface vlan 2 ip address 172.31.19.254 255.255.255.0 exit interface vlan 4 ip address 172.31.16.254 255.255.255.0 ! interface Gi1/0/1 description 'Link to L7Router01' switchport mode trunk switchport trunk allowed vlan except 3,7-4093 exit ! and on the Cisco the following: interface FastEthernet0/0 ip address 172.31.14.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.2 description Accounts VLAN encapsulation dot1Q 2 ip address 172.31.19.1 255.255.255.0 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.4 description Voice VLAN encapsulation dot1Q 4 ip address 172.31.16.1 255.255.255.0 ip nat inside ip virtual-reassembly ! So what I'm doing is moving clients over so that their default gateway is a 172.31.x.254 address rather than a 172.31.x.1 address. This works great for inter-vlan routing, I have no issues with this. The switch can also access the router no worries, and users on the 172.31.14.0/24 network can access all interfaces and sub-interfaces on the router, including 172.31.14.1. They can also access all of the interfaces that the router connects off to, no worries there. The problem I have is that users on the 172.31.16.0/24 and 172.31.19.0/24 subnets cannot access either 172.31.14.1 or any of the subnets the router connects to. They can, however, connect to BOTH of the sub interfaces on the router from either subnet. What am I missing here? Why can't the vlans connect to the non-sub interface on the router? Are tagged packets being sent to this interface?

  Read the article

• Excessive CPU Utilization for Bind 9.8.1 `named` processes

  - by justinzane

  I just noticed that named is eating vast amounts of CPU time for a very small network with only a few domains. Can someone help me determine what is misconfigured, please? Or how to debug this. top top - 14:13:08 up 25 days, 14:16, 1 user, load average: 1.04, 1.04, 1.05 Tasks: 149 total, 1 running, 148 sleeping, 0 stopped, 0 zombie %Cpu(s): 17.3 us, 4.3 sy, 0.0 ni, 78.2 id, 0.1 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 2042776 total, 1347916 used, 694860 free, 249396 buffers KiB Swap: 3976080 total, 30552 used, 3945528 free, 574164 cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 17445 bind 20 0 244m 42m 3124 S 99.4 2.2 2345:03 named rndc stats +++ Statistics Dump +++ (1352931389) ++ Incoming Requests ++ 65869 QUERY ++ Incoming Queries ++ 31809 A 241 NS 3 CNAME 27455 SOA 276 PTR 123 MX 462 TXT 5400 AAAA 7 A6 1 DS 14 DNSKEY 15 SPF 55 AXFR 8 ANY ++ Outgoing Queries ++ [View: internal] 22206 A 509 NS 10 SOA 25 PTR 12 MX 524 TXT 4851 AAAA 62 DNSKEY 19 SPF 3157 DLV [View: external] 87 A 2 NS 80 AAAA 120 DNSKEY 7 DLV [View: _bind] ++ Name Server Statistics ++ 65869 IPv4 requests received 27670 requests with EDNS(0) received 112 TCP requests received 65652 responses sent 20 truncated responses sent 27670 responses with EDNS(0) sent 62920 queries resulted in successful answer 37117 queries resulted in authoritative answer 28482 queries resulted in non authoritative answer 7 queries resulted in referral answer 591 queries resulted in nxrrset 53 queries resulted in SERVFAIL 2081 queries resulted in NXDOMAIN 14530 queries caused recursion 162 duplicate queries received 55 requested transfers completed ++ Zone Maintenance Statistics ++ 109536 IPv4 notifies sent ++ Resolver Statistics ++ [Common] [View: internal] 29362 IPv4 queries sent 2013 IPv6 queries sent 28531 IPv4 responses received 4209 NXDOMAIN received 6 SERVFAIL received 31 FORMERR received 32 EDNS(0) query failures 3359 query retries 836 query timeouts 5348 IPv4 NS address fetches 3271 IPv6 NS address fetches 83 IPv4 NS address fetch failed 2779 IPv6 NS address fetch failed 17421 DNSSEC validation attempted 12731 DNSSEC validation succeeded 4690 DNSSEC NX validation succeeded 21104 queries with RTT 10-100ms 7418 queries with RTT 100-500ms 3 queries with RTT 500-800ms 1 queries with RTT 800-1600ms [View: external] 192 IPv4 queries sent 104 IPv6 queries sent 192 IPv4 responses received 2 NXDOMAIN received 104 query retries 44 IPv4 NS address fetches 44 IPv6 NS address fetches 1 IPv4 NS address fetch failed 1 IPv6 NS address fetch failed 4 DNSSEC validation attempted 3 DNSSEC validation succeeded 1 DNSSEC NX validation succeeded 152 queries with RTT 10-100ms 40 queries with RTT 100-500ms [View: _bind] ++ Cache DB RRsets ++ [View: internal (Cache: internal)] 2007 A 652 NS 131 CNAME 1 MX 32 TXT 421 AAAA 28 DS 244 RRSIG 110 NSEC 3 DNSKEY 2 !A 2 !TXT 89 !AAAA 2 !SPF 14 !DLV 148 NXDOMAIN [View: external (Cache: external)] 55 A 12 NS 34 AAAA 2 DS 10 RRSIG 1 DNSKEY [View: _bind (Cache: _bind)] ++ Socket I/O Statistics ++ 82958 UDP/IPv4 sockets opened 2118 UDP/IPv6 sockets opened 4 TCP/IPv4 sockets opened 1 TCP/IPv6 sockets opened 82956 UDP/IPv4 sockets closed 2117 UDP/IPv6 sockets closed 58 TCP/IPv4 sockets closed 15 UDP/IPv4 socket bind failures 2117 UDP/IPv6 socket connect failures 29554 UDP/IPv4 connections established 59 TCP/IPv4 connections accepted 2117 UDP/IPv6 send errors 5 UDP/IPv4 recv errors ++ Per Zone Query Statistics ++ --- Statistics Dump --- (1352931389)

  Read the article

• AWS EC2 instance not pingable or available in browser

  - by Slimmons

  I've seen this questions asked other places, but now I've run through every fix proposed in other questions so I'm re asking it here, in hopes that someone will have a different solution. Problem: I have a EC2 instance, and I can ssh into it and work on it, and I have a Elastic ip set to it. I am unable to ping this machine, or log in to it using my browser. Solutions mentioned and tried: service httpd start i. response I get is "unrecognized service" ii. when I run apache2ctl -k start, it shows "httpd already running", so I'm assuming httpd is not the problem, it's just possibly named something else because of apache2, or for whatever reason. I went into EC2-Security Group- Default (which is the one I used.)-inbound, and everything there is set up correctly (I'm assuming). There it shows 80(HTTP) 0.0.0.0/0. 443(HTTPS) 0.0.0.0/0, and various other servies with their ports and 0.0.0.0/0 next to them. I also enabled a rule for enabling ICMP Request All on 0.0.0.0/0 temporarily for testing purposes I've tried disabling the iptables with "service ufw stop" Just in case I'm doing something really stupid, because I'm not all that used to connecting to web servers that I've spun up, I'm typing in the address to the machine into the url like this (assuming my ip address was ip.address). i. http:/(slash)ip.address/ ii. ip.address iii. https:/(slash)ip.address/ iv. ip.address/webFolderName/ v. http:/(slash)ip.address/webFolderName/ None of the attempts worked, and the only thing I haven't tried that i've seen is to start wireshark on the machine, and see if the requests are reaching it, and it's just ignoring them. I'm not sure I want to do that yet, since A). I'm not 100% positive how to use wireshark without the gui, since it's the only way I've ever used it (I really should get used to it in terminal, but I didn't even know you could). B). It really seems like I'm missing something simple in getting this to work. Thanks in advance for any help.

  Read the article

• PPTP ping client to client error

  - by Linux Intel

  I installed pptp server on a centos 6 64bit server PPTP Server ip : 55.66.77.10 PPTP Local ip : 10.0.0.1 Client1 IP : 10.0.0.60 centos 5 64bit Client2 IP : 10.0.0.61 centos5 64bit PPTP Server can ping Client1 And client 1 can ping PPTP Server PPTP Server can ping Client2 And client 2 can ping PPTP Server The problem is client 1 can not ping Client 2 route -n on PPTP Server Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.60 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.0.61 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1 55.66.77.10 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 55.66.77.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 1 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 70.14.13.19 255.255.255.255 UGH 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 70.14.13.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 2 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 84.56.120.60 255.255.255.255 UGH 0 0 0 eth1 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 84.56.120.60 0.0.0.0 UG 0 0 0 eth1 cat /etc/ppp/options.pptpd on PPTP server ############################################################################### # $Id: options.pptpd,v 1.11 2005/12/29 01:21:09 quozl Exp $ # # Sample Poptop PPP options file /etc/ppp/options.pptpd # Options used by PPP when a connection arrives from a client. # This file is pointed to by /etc/pptpd.conf option keyword. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 and the kernel MPPE module. ############################################################################### # Authentication # Name of the local system for authentication purposes # (must match the second field in /etc/ppp/chap-secrets entries) name pptpd # Strip the domain prefix from the username before authentication. # (applies if you use pppd with chapms-strip-domain patch) #chapms-strip-domain # Encryption # (There have been multiple versions of PPP with encryption support, # choose with of the following sections you will use.) # BSD licensed ppp-2.4.2 upstream with MPPE only, kernel module ppp_mppe.o # {{{ refuse-pap refuse-chap refuse-mschap # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. require-mschap-v2 # Require MPPE 128-bit encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) require-mppe-128 # }}} # OpenSSL licensed ppp-2.4.1 fork with MPPE only, kernel module mppe.o # {{{ #-chap #-chapms # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. #+chapms-v2 # Require MPPE encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) #mppe-40 # enable either 40-bit or 128-bit, not both #mppe-128 #mppe-stateless # }}} # Network and Routing # If pppd is acting as a server for Microsoft Windows clients, this # option allows pppd to supply one or two DNS (Domain Name Server) # addresses to the clients. The first instance of this option # specifies the primary DNS address; the second instance (if given) # specifies the secondary DNS address. #ms-dns 10.0.0.1 #ms-dns 10.0.0.2 # If pppd is acting as a server for Microsoft Windows or "Samba" # clients, this option allows pppd to supply one or two WINS (Windows # Internet Name Services) server addresses to the clients. The first # instance of this option specifies the primary WINS address; the # second instance (if given) specifies the secondary WINS address. #ms-wins 10.0.0.3 #ms-wins 10.0.0.4 # Add an entry to this system's ARP [Address Resolution Protocol] # table with the IP address of the peer and the Ethernet address of this # system. This will have the effect of making the peer appear to other # systems to be on the local ethernet. # (you do not need this if your PPTP server is responsible for routing # packets to the clients -- James Cameron) proxyarp # Normally pptpd passes the IP address to pppd, but if pptpd has been # given the delegate option in pptpd.conf or the --delegate command line # option, then pppd will use chap-secrets or radius to allocate the # client IP address. The default local IP address used at the server # end is often the same as the address of the server. To override this, # specify the local IP address here. # (you must not use this unless you have used the delegate option) #10.8.0.100 # Logging # Enable connection debugging facilities. # (see your syslog configuration for where pppd sends to) debug # Print out all the option values which have been set. # (often requested by mailing list to verify options) #dump # Miscellaneous # Create a UUCP-style lock file for the pseudo-tty to ensure exclusive # access. lock # Disable BSD-Compress compression nobsdcomp # Disable Van Jacobson compression # (needed on some networks with Windows 9x/ME/XP clients, see posting to # poptop-server on 14th April 2005 by Pawel Pokrywka and followups, # http://marc.theaimsgroup.com/?t=111343175400006&r=1&w=2 ) novj novjccomp # turn off logging to stderr, since this may be redirected to pptpd, # which may trigger a loopback nologfd # put plugins here # (putting them higher up may cause them to sent messages to the pty) cat /etc/ppp/options.pptp on Client1 and Client2 ############################################################################### # $Id: options.pptp,v 1.3 2006/03/26 23:11:05 quozl Exp $ # # Sample PPTP PPP options file /etc/ppp/options.pptp # Options used by PPP when a connection is made by a PPTP client. # This file can be referred to by an /etc/ppp/peers file for the tunnel. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 or later from http://ppp.samba.org/ # and the kernel MPPE module available from the CVS repository also on # http://ppp.samba.org/, which is packaged for DKMS as kernel_ppp_mppe. ############################################################################### # Lock the port lock # Authentication # We don't need the tunnel server to authenticate itself noauth # We won't do PAP, EAP, CHAP, or MSCHAP, but we will accept MSCHAP-V2 # (you may need to remove these refusals if the server is not using MPPE) refuse-pap refuse-eap refuse-chap refuse-mschap # Compression # Turn off compression protocols we know won't be used nobsdcomp nodeflate # Encryption # (There have been multiple versions of PPP with encryption support, # choose which of the following sections you will use. Note that MPPE # requires the use of MSCHAP-V2 during authentication) # # Note that using PPTP with MPPE and MSCHAP-V2 should be considered # insecure: # http://marc.info/?l=pptpclient-devel&m=134372640219039&w=2 # https://github.com/moxie0/chapcrack/blob/master/README.md # http://technet.microsoft.com/en-us/security/advisory/2743314 # http://ppp.samba.org/ the PPP project version of PPP by Paul Mackarras # ppp-2.4.2 or later with MPPE only, kernel module ppp_mppe.o # If the kernel is booted in FIPS mode (fips=1), the ppp_mppe.ko module # is not allowed and PPTP-MPPE is not available. # {{{ # Require MPPE 128-bit encryption #require-mppe-128 # }}} # http://mppe-mppc.alphacron.de/ fork from PPP project by Jan Dubiec # ppp-2.4.2 or later with MPPE and MPPC, kernel module ppp_mppe_mppc.o # {{{ # Require MPPE 128-bit encryption #mppe required,stateless # }}} IPtables are stopped on clients and server, Also net.ipv4.ip_forward = 1 is enabled on PPTP Server. How can i solve this problem .?

  Read the article

< Previous Page | 86 87 88 89 90 91 92 93 94 95 96 97  | Next Page >