Search Results

Search found 2644 results on 106 pages for 'gnu classpath'.

Page 91/106 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

• Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

  - by Tom

  I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

  Read the article

• Ubuntu 12.04 LTS initramfs-tools dependency issue

  - by Mike

  I know this has been asked several times, but each issue and resolution seems different. I've tried almost everything I could think of, but I can't fix this. I have a VM (VMware I think) running 12.04.03 LTS which has stuck dependencies. The VM is on a rented host, running a live system so I don't want to break it (further). uname -a Linux support 3.5.0-36-generic #57~precise1-Ubuntu SMP Thu Jun 20 18:21:09 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Some more: sudo apt-get update [sudo] password for tracker: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run ‘apt-get -f install’ to correct these. The following packages have unmet dependencies. initramfs-tools : Depends: initramfs-tools-bin (< 0.99ubuntu13.1.1~) but 0.99ubuntu13.3 is installed E: Unmet dependencies. Try using -f. sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: initramfs-tools The following packages will be upgraded: initramfs-tools 1 upgraded, 0 newly installed, 0 to remove and 2 not upgraded. 2 not fully installed or removed. Need to get 0 B/50.3 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y dpkg: dependency problems prevent configuration of initramfs-tools: initramfs-tools depends on initramfs-tools-bin (<< 0.99ubuntu13.1.1~); however: Version of initramfs-tools-bin on system is 0.99ubuntu13.3. dpkg: error processing initramfs-tools (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates it's a follow-up error from a previous failure. dpkg: dependency problems prevent configuration of apparmor: apparmor depends on initramfs-tools; however: Package initramfs-tools is not configured yet. dpkg: error processing apparmor (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates it's a follow-up error from a previous failure. Errors were encountered while processing: initramfs-tools apparmor E: Sub-process /usr/bin/dpkg returned an error code (1) If I look at the policy behind initramfs-tools / bin I get: apt-cache policy initramfs-tools initramfs-tools: Installed: 0.99ubuntu13.1 Candidate: 0.99ubuntu13.3 Version table: 0.99ubuntu13.3 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise-updates/main amd64 Packages *** 0.99ubuntu13.1 0 100 /var/lib/dpkg/status 0.99ubuntu13 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise/main amd64 Packages apt-cache policy initramfs-tools-bin initramfs-tools-bin: Installed: 0.99ubuntu13.3 Candidate: 0.99ubuntu13.3 Version table: *** 0.99ubuntu13.3 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise-updates/main amd64 Packages 100 /var/lib/dpkg/status 0.99ubuntu13 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise/main amd64 Packages So the issue seems to be I have 0.99ubuntu13.3 for initramfs-tools-bin yet 0.99ubuntu13.1 for initramfs-tools, and can't upgrade to 0.99ubuntu13.3. I've performed apt-get clean/autoclean/install -f/upgrade -f many times but they won't resolve. I can think of only 2 other 'solutions': Edit the dpkg dependency list to trick it into doing the installation with a broken dependency. This seems very dodgy and it would be a last resort Downgrade both initramfs-tools and initramfs-tools-bin to 0.99ubuntu13 from the precise/main sources and hope that would get them in step. However I'm not sure if this will be possible, or whether it would introduce more issues. I'm not sure how this situation arise in the first place. /boot was 96% full; it's now 56% full (it's tiny - 64MB ... this is what I got from the hosting company). Can anyone offer advice please?

  Read the article

• Graphical driver 13.10 ATI RV630

  - by Michael Cephalus

  I started updating the distro from 13.04 to 13.10. Then I got my hands on a Radeon HD 2600. I installed the RV630 compatible Catalystdriver from the official webpage. Then xserver crashed everytime I opened a browser or vlc fx. I took notice that there was no driver listed in configuration underneath. michael@statubtunu:~$ lshw -c video WARNING: you should run this program as super-user. *-display UNCLAIMED description: VGA compatible controller product: RV630 PRO [Radeon HD 2600 PRO] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list configuration: latency=0 resources: memory:d0000000-dfffffff memory:e0500000-e050ffff ioport:1000(size=256) memory:e0000000-e001ffff i installed additional drivers from jockey and the ubuntu softwarecenter ati-driver. though that only made it to crash xserver completely and when i type: michael@statubtunu:~$ sudo startx X.Org X Server 1.14.3 Release Date: 2013-09-12 X Protocol Version 11, Revision 0 Build Operating System: Linux 3.2.0-37-generic i686 Ubuntu Current Operating System: Linux statubtunu 3.11.0-13-generic #20-Ubuntu SMP Wed Oct 23 17:26:33 UTC 2013 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.11.0-13-generic root=UUID=8fb2e395-0ea2-4f45-ac66-225696b7ce2c ro quiet splash vt.handoff=7 Build Date: 15 October 2013 09:23:29AM xorg-server 2:1.14.3-3ubuntu2 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.30.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Nov 12 18:50:02 2013 (==) Using system config directory "/usr/share/X11/xorg.conf.d" Initializing built-in extension Generic Event Extension Initializing built-in extension SHAPE Initializing built-in extension MIT-SHM Initializing built-in extension XInputExtension Initializing built-in extension XTEST Initializing built-in extension BIG-REQUESTS Initializing built-in extension SYNC Initializing built-in extension XKEYBOARD Initializing built-in extension XC-MISC Initializing built-in extension SECURITY Initializing built-in extension XINERAMA Initializing built-in extension XFIXES Initializing built-in extension RENDER Initializing built-in extension RANDR Initializing built-in extension COMPOSITE Initializing built-in extension DAMAGE Initializing built-in extension MIT-SCREEN-SAVER Initializing built-in extension DOUBLE-BUFFER Initializing built-in extension RECORD Initializing built-in extension DPMS Initializing built-in extension X-Resource Initializing built-in extension XVideo Initializing built-in extension XVideo-MotionCompensation Initializing built-in extension SELinux Initializing built-in extension XFree86-VidModeExtension Initializing built-in extension XFree86-DGA Initializing built-in extension XFree86-DRI Initializing built-in extension DRI2 Loading extension GLX ERROR: could not insert 'fglrx': No such device (II) [KMS] drm report modesetting isn't supported. (EE) (EE) Backtrace: (EE) 0: /usr/bin/X (xorg_backtrace+0x49) [0xb77780b9] (EE) 1: /usr/bin/X (0xb75d8000+0x1a3e24) [0xb777be24] (EE) 2: (vdso) (__kernel_rt_sigreturn+0x0) [0xb75b540c] (EE) 3: /usr/bin/X (xf86findOption+0x2a) [0xb7681daa] (EE) 4: /usr/bin/X (xf86findOptionValue+0x23) [0xb7681f43] (EE) 5: /usr/bin/X (0xb75d8000+0x7ebfd) [0xb7656bfd] (EE) 6: /usr/bin/X (xf86ProcessOptions+0x37) [0xb7657507] (EE) 7: /usr/lib/xorg/modules/libvbe.so (vbeDoEDID+0xe7) [0xb5eb8647] (EE) 8: /usr/lib/xorg/modules/drivers/vesa_drv.so (0xb5ee7000+0x287c) [0xb5ee987c] (EE) 9: /usr/bin/X (InitOutput+0xb23) [0xb7659c33] (EE) 10: /usr/bin/X (0xb75d8000+0x2a30b) [0xb760230b] (EE) 11: /lib/i386-linux-gnu/libc.so.6 (__libc_start_main+0xf5) [0xb71ba905] (EE) 12: /usr/bin/X (0xb75d8000+0x2a908) [0xb7602908] (EE) (EE) Segmentation fault at address 0x5 (EE) Fatal server error: (EE) Caught signal 11 (Segmentation fault). Server aborting (EE) (EE) Please consult the The X.Org Foundation support at for help. (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information. (EE) (EE) Server terminated with error (1). Closing log file. This is what comes, but no GUI. Is there any way to deal with this?

  Read the article

• Can't connect to certain HTTPS sites

  - by mind.blank

  I've just moved to a new apartment and with internet connection via a router and I'm finding that I can't connect to quite a few sites that use SSL. For example trying to connect to PayPal: curl -v https://paypal.com * About to connect() to paypal.com port 443 (#0) * Trying 66.211.169.3... connected * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * SSLv3, TLS handshake, Client hello (1): * Unknown SSL protocol error in connection to paypal.com:443 * Closing connection #0 curl: (35) Unknown SSL protocol error in connection to paypal.com:443 curl -v -ssl https://paypal.com gives the same output. For some sites it works: curl -v https://www.google.com * About to connect() to www.google.com port 443 (#0) * Trying 74.125.235.112... connected * successfully set certificate verify locations: * CAfile: none CApath: /etc/ssl/certs * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Server key exchange (12): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSL connection using ECDHE-RSA-RC4-SHA * Server certificate: * subject: C=US; ST=California; L=Mountain View; O=Google Inc; CN=www.google.com * start date: 2011-10-26 00:00:00 GMT * expire date: 2013-09-30 23:59:59 GMT * common name: www.google.com (matched) * issuer: C=ZA; O=Thawte Consulting (Pty) Ltd.; CN=Thawte SGC CA * SSL certificate verify ok. > GET / HTTP/1.1 > User-Agent: curl/7.22.0 (x86_64-pc-linux-gnu) libcurl/7.22.0 OpenSSL/1.0.1 zlib/1.2.3.4 libidn/1.23 librtmp/2.3 > Host: www.google.com > Accept: */* > < HTTP/1.1 302 Found < Location: https://www.google.co.jp/ . . . I'm using Ubuntu 12.04, with Windows 7 installed as well. These sites work on Windows :( Not sure if this information helps but I ran ifconfig and got the following: eth0 Link encap:Ethernet HWaddr 1c:c1:de:bc:e2:4f inet6 addr: 2408:c3:7fff:991:686b:8d18:81b3:8dd1/64 Scope:Global inet6 addr: 2408:c3:7fff:991:1ec1:deff:febc:e24f/64 Scope:Global inet6 addr: fe80::1ec1:deff:febc:e24f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:87075 errors:0 dropped:0 overruns:0 frame:0 TX packets:54522 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:78167937 (78.1 MB) TX bytes:10016891 (10.0 MB) Interrupt:46 Base address:0x4000 eth1 Link encap:Ethernet HWaddr ac:81:12:0d:93:80 inet6 addr: fe80::ae81:12ff:fe0d:9380/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:498 TX packets:0 errors:26 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:630 errors:0 dropped:0 overruns:0 frame:0 TX packets:630 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39592 (39.5 KB) TX bytes:39592 (39.5 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:180.57.228.200 P-t-P:118.23.8.175 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:39631 errors:0 dropped:0 overruns:0 frame:0 TX packets:22391 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:43462054 (43.4 MB) TX bytes:2834628 (2.8 MB)

  Read the article

• How to remove synaptic without installing all the unwanted packages?

  - by Jay

  I am trying to uninstall synaptic. I prefer using apt-get and other command line tools to manage my packages. So I do not need synaptic and the software manager. I'm trying to remove both of them using apt-get. Its a new box. Recently installed Linux Mint mate 15. After installation, the only thing I did was, sudo apt-get update and sudo apt-get dist-upgrade After that, I did this command for removing synaptic, sudo apt-get remove --purge synaptic But this gives me a very weird output, Reading package lists... Done Building dependency tree Reading state information... Done The following packages were automatically installed and are no longer required: apturl-kde icoutils kate-data katepart kde-runtime kde-runtime-data kdelibs-bin kdelibs5-data kdelibs5-plugins kdesudo kdoctools kubuntu-debug-installer libattica0.4 libdlrestrictions1 libkactivities-bin libkactivities-models1 libkactivities6 libkatepartinterfaces4 libkcmutils4 libkde3support4 libkdeclarative5 libkdecore5 libkdesu5 libkdeui5 libkdewebkit5 libkdnssd4 libkemoticons4 libkfile4 libkhtml5 libkidletime4 libkio5 libkjsapi4 libkjsembed4 libkmediaplayer4 libknewstuff3-4 libknotifyconfig4 libkntlm4 libkparts4 libkpty4 libkrosscore4 libktexteditor4 libkxmlrpcclient4 libnepomuk4 libnepomukcore4abi1 libnepomukquery4a libnepomukutils4 libntrack-qt4-1 libntrack0 libphonon4 libplasma3 libpolkit-qt-1-1 libpoppler-qt4-4 libqapt2 libqapt2-runtime libqca2 libqt4-qt3support libsolid4 libsoprano4 libstreamanalyzer0 libstreams0 libthreadweaver4 libvirtodbc0 nepomuk-core nepomuk-core-data ntrack-module-libnl-0 odbcinst odbcinst1debian2 oxygen-icon-theme phonon phonon-backend-gstreamer plasma-scriptengine-javascript qapt-batch shared-desktop-ontologies soprano-daemon virtuoso-minimal virtuoso-opensource-6.1-bin virtuoso-opensource-6.1-common Use 'apt-get autoremove' to remove them. The following extra packages will be installed: apturl-kde icoutils kate-data katepart kde-runtime kde-runtime-data kdelibs-bin kdelibs5-data kdelibs5-plugins kdesudo kdoctools kubuntu-debug-installer libattica0.4 libdlrestrictions1 libkactivities-bin libkactivities-models1 libkactivities6 libkatepartinterfaces4 libkcmutils4 libkde3support4 libkdeclarative5 libkdecore5 libkdesu5 libkdeui5 libkdewebkit5 libkdnssd4 libkemoticons4 libkfile4 libkhtml5 libkidletime4 libkio5 libkjsapi4 libkjsembed4 libkmediaplayer4 libknewstuff3-4 libknotifyconfig4 libkntlm4 libkparts4 libkpty4 libkrosscore4 libktexteditor4 libkxmlrpcclient4 libnepomuk4 libnepomukcore4abi1 libnepomukquery4a libnepomukutils4 libntrack-qt4-1 libntrack0 libphonon4 libplasma3 libpolkit-qt-1-1 libpoppler-qt4-4 libqapt2 libqapt2-runtime libqca2 libqt4-qt3support libsolid4 libsoprano4 libstreamanalyzer0 libstreams0 libthreadweaver4 libvirtodbc0 libxml2-utils nepomuk-core nepomuk-core-data ntrack-module-libnl-0 odbcinst odbcinst1debian2 oxygen-icon-theme phonon phonon-backend-gstreamer plasma-scriptengine-javascript qapt-batch shared-desktop-ontologies soprano-daemon virtuoso-minimal virtuoso-opensource-6.1-bin virtuoso-opensource-6.1-common Suggested packages: libterm-readline-gnu-perl libterm-readline-perl-perl djvulibre-bin finger hspell libqca2-plugin-cyrus-sasl libqca2-plugin-gnupg libqca2-plugin-ossl phonon-backend-vlc phonon-backend-xine phonon-backend-mplayer The following packages will be REMOVED: aptoncd* apturl* mintupdate* mintwelcome* synaptic* The following NEW packages will be installed: apturl-kde icoutils kate-data katepart kde-runtime kde-runtime-data kdelibs-bin kdelibs5-data kdelibs5-plugins kdesudo kdoctools kubuntu-debug-installer libattica0.4 libdlrestrictions1 libkactivities-bin libkactivities-models1 libkactivities6 libkatepartinterfaces4 libkcmutils4 libkde3support4 libkdeclarative5 libkdecore5 libkdesu5 libkdeui5 libkdewebkit5 libkdnssd4 libkemoticons4 libkfile4 libkhtml5 libkidletime4 libkio5 libkjsapi4 libkjsembed4 libkmediaplayer4 libknewstuff3-4 libknotifyconfig4 libkntlm4 libkparts4 libkpty4 libkrosscore4 libktexteditor4 libkxmlrpcclient4 libnepomuk4 libnepomukcore4abi1 libnepomukquery4a libnepomukutils4 libntrack-qt4-1 libntrack0 libphonon4 libplasma3 libpolkit-qt-1-1 libpoppler-qt4-4 libqapt2 libqapt2-runtime libqca2 libqt4-qt3support libsolid4 libsoprano4 libstreamanalyzer0 libstreams0 libthreadweaver4 libvirtodbc0 libxml2-utils nepomuk-core nepomuk-core-data ntrack-module-libnl-0 odbcinst odbcinst1debian2 oxygen-icon-theme phonon phonon-backend-gstreamer plasma-scriptengine-javascript qapt-batch shared-desktop-ontologies soprano-daemon virtuoso-minimal virtuoso-opensource-6.1-bin virtuoso-opensource-6.1-common 0 upgraded, 78 newly installed, 5 to remove and 0 not upgraded. Need to get 60.9 MB of archives. After this operation, 146 MB of additional disk space will be used. Do you want to continue [Y/n]? n Abort. As you can see, apt-get is trying to install the same packages that it is asking me to autoremove. Could someone please tell me, how to uninstall synaptic properly? Or am I missing something? Just for the record, I also did, sudo apt-get autoremove --purge like it asked me to ... and this is what I got, Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 6 not upgraded.

  Read the article

• Migrating a WebLogic Domain from a 32 to a 64 bit JVM/Architecture

  - by adejuanc

  Currently on 32 bit OS which presents a physical constraint when trying to allocate memory. By limit, a 32 bit OS, will not be able to allocate more than 3 GB on a Linux environment, or 2 GB for Windows environment (not considering Physical Address Extension (PAE) implementation, which can increase the maximum allocatable memory). When this limit is reached, a migration to a 64 bit architecture is recommended. Below are the steps on how to install a 64 WebLogic Server version, along with a 64 Bit JVM and then how to migrate the domain to this new environment. Weblogic Server Version: WebLogic Server Version: 10.3.4.0 OS: Linux adejuan-cl.cl.oracle.com 2.6.18-194.el5 #1 SMP Mon Jan 01 22:10:29 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux JVM:java version "1.6.0_22" Java(TM) SE Runtime Environment (build 1.6.0_22-b04) Oracle JRockit(R) (build R28.1.1-13-139783-1.6.0_22-20101206-0136-linux-x86_64, compiled mode) To create migration template: 1. Execute $<WLS_HOME>/wlserver_10.3/common/bin/config_builder.sh 2. Create Domain Template. 3. Select Domain to migrate. 4. Enter the name of template and other info. Click next. 5. Using Add Button, Select libraries you want to add under lib folder. copy jdbc data sources you would like to have under config/jdbc folder. If you want to have log4j configuration, copy log4j.xml under domain_root folder. 6. Select data base for the domain and click next. 7. Enter Admin Server Name and port numbers. Click next. 8. Enter username and password. Click next. Select No if you don want to add users/groups/roles 9. Click next until reach button create. This will create a jar file that is needed for the next action plan. To install and migrate domain to 64 bit architecture. 1. Install JVM Jrockit R28.1.1.13 on environment. (uncompress zip folder on a known location) 2. Go to JRockit_Home/bin and execute $ java -d64 -jar wls1034_generic.jar 3. When prompt, select JRockit JVM in browse menu, and wait for installation to finish. 4. Go to <WLS_HOME>/wlserver_10.3/common/bin and execute $ ./config.sh 5. Select Create a new Weblogic domain 6. Select Base this domain on an existing template and select browse. 7. Select jar file created on previous action plan. 8. Select Name of domain. Maintain in most cases. 9. Select user name and password. Maintain in most cases. 10. Select Jrockit SDK 1.6.0_22 and click next. 11. Confirm all JMS/JDBC/security configuration. 12. On select Optional Configuration, reconfigure if necessary. 13. Check on Configuration summary for all domain configuration. 14. Click on create, to finish up domain import. Note: Always when installing a 64 bit WLS, it's necessary to install first the 64 JVM and then run the generic installer with the -d64 bit option. If this is not performed, the installation will be the 32 default version. For more information, please refer: http://download.oracle.com/docs/cd/E13188_01/jrockit/docs50/dev_faq.html#pae

  Read the article

• How to make Ubuntu recognize an unknown external display (so I can adjust its resolution)?

  - by WagnerAA

  I have a Dell laptop with an external monitor attached (a Samsumg SyncMaster 931c). My laptop display was recognized, and I can adjust its optimum resolution. My external display is still unknown, thus I'm stuck at a lower resolution (1024x768): I tried the "Detect Displays" button, but it didn't work, nothing happens. I recently upgraded from Ubuntu 12.04 to 12.10. Things were working before. I don't know if I can actually change this configuration, or if this is a bug. I searched for an answer here and also in Launchpad's website, but found none. I even tried to install Nvidia drivers, and just messed things up. It seems I wasn't even using nvidia before, as I guessed by looking at my additional drivers configuration: My laptop has an Intel chipset, I guess: $ dpkg --get-selections | grep -i -e nvidia -e intel intel-gpu-tools install libdrm-intel1:amd64 install libdrm-intel1:i386 install nvidia-common install xserver-xorg-video-intel install I don't have an xorg.conf file (I think this is nvidia related, am I right?): $ cat /etc/X11/xorg.conf cat: /etc/X11/xorg.conf: No such file or directory $ ls -l /etc/X11/ total 76 drwxr-xr-x 2 root root 4096 Out 19 23:41 app-defaults drwxr-xr-x 2 root root 4096 Abr 25 2012 cursors -rw-r--r-- 1 root root 18 Abr 25 2012 default-display-manager drwxr-xr-x 4 root root 4096 Abr 25 2012 fonts -rw-r--r-- 1 root root 17394 Dez 3 2009 rgb.txt lrwxrwxrwx 1 root root 13 Mai 1 03:33 X -> /usr/bin/Xorg drwxr-xr-x 3 root root 4096 Out 19 23:41 xinit drwxr-xr-x 2 root root 4096 Jan 23 2012 xkb -rw-r--r-- 1 root root 0 Out 24 08:55 xorg.conf.nvidia-xconfig-original -rwxr-xr-x 1 root root 709 Abr 1 2010 Xreset drwxr-xr-x 2 root root 4096 Out 19 10:08 Xreset.d drwxr-xr-x 2 root root 4096 Out 19 10:08 Xresources -rwxr-xr-x 1 root root 3730 Jan 20 2012 Xsession drwxr-xr-x 2 root root 4096 Out 20 00:11 Xsession.d -rw-r--r-- 1 root root 265 Jul 1 2008 Xsession.options -rw-r--r-- 1 root root 13 Ago 15 06:43 XvMCConfig -rw-r--r-- 1 root root 601 Abr 25 2012 Xwrapper.config Here is some information I gathered by looking at other related posts: $ sudo lshw -C display; lsb_release -a; uname -a *-display:0 description: VGA compatible controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 07 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:48 memory:f6800000-f6bfffff memory:d0000000-dfffffff ioport:1800(size=8) *-display:1 UNCLAIMED description: Display controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 07 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:f6100000-f61fffff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch:cxx-3.0-amd64:cxx-3.0-noarch:cxx-3.1-amd64:cxx-3.1-noarch:cxx-3.2-amd64:cxx-3.2-noarch:cxx-4.0-amd64:cxx-4.0-noarch:desktop-3.1-amd64:desktop-3.1-noarch:desktop-3.2-amd64:desktop-3.2-noarch:desktop-4.0-amd64:desktop-4.0-noarch:graphics-2.0-amd64:graphics-2.0-noarch:graphics-3.0-amd64:graphics-3.0-noarch:graphics-3.1-amd64:graphics-3.1-noarch:graphics-3.2-amd64:graphics-3.2-noarch:graphics-4.0-amd64:graphics-4.0-noarch:printing-3.2-amd64:printing-3.2-noarch:printing-4.0-amd64:printing-4.0-noarch:qt4-3.1-amd64:qt4-3.1-noarch Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux Batcave 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ xrandr -q Screen 0: minimum 320 x 200, current 2304 x 800, maximum 32767 x 32767 LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 286mm x 1790mm 1280x800 59.9*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+1280+32 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 DP1 disconnected (normal left inverted right x axis y axis) If there's anything else I can do, any other information I can post here, to help me configure this external display, please let me know. If this is actually a bug, I apologize (I know bugs are not allowed here), but I really wasn't sure. And I will promptly file a bug report in Launchpad if that's the case. Thanks a lot in advance. ;)

  Read the article

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• edited and reversed changes on .htaccess - site starts redirecting to .comindex.php/

  - by Aurigae

  Site is a Joomla 2.5 site. I wanted to add a non www to www redirect to the htaccess file, did so, then the redirection went mad, reversed but still the site redirects. When i click view site in admin panel, i get linked to http://domain.comindex.php/ The website is http://www.domain.com Visiting the website URL works without www, but once you click on projects it acts mad too. Projects is managed with joomshopping extension. EDIT: the redirect also happens when rewrite is deactivated in admin panel. ## # @package Joomla # @copyright Copyright (C) 2005 - 2012 Open Source Matters. All rights reserved. # @license GNU General Public License version 2 or later; see LICENSE.txt ## ## # READ THIS COMPLETELY IF YOU CHOOSE TO USE THIS FILE! # # The line just below this section: 'Options +FollowSymLinks' may cause problems # with some server configurations. It is required for use of mod_rewrite, but may already # be set by your server administrator in a way that dissallows changing it in # your .htaccess file. If using it causes your server to error out, comment it out (add # to # beginning of line), reload your site in your browser and test your sef url's. If they work, # it has been set by your server administrator and you do not need it set here. ## ## Can be commented out if causes errors, see notes above. Options +FollowSymLinks ## Mod_rewrite in use. RewriteEngine On ## Begin - Rewrite rules to block out some common exploits. # If you experience problems on your site block out the operations listed below # This attempts to block the most common type of exploit `attempts` to Joomla! # # Block out any script trying to base64_encode data within the URL. RewriteCond %{QUERY_STRING} base64_encode[^(]*\([^)]*\) [OR] # Block out any script that includes a <script> tag in URL. RewriteCond %{QUERY_STRING} (<|%3C)([^s]*s)+cript.*(>|%3E) [NC,OR] # Block out any script trying to set a PHP GLOBALS variable via URL. RewriteCond %{QUERY_STRING} GLOBALS(=|\[|\%[0-9A-Z]{0,2}) [OR] # Block out any script trying to modify a _REQUEST variable via URL. RewriteCond %{QUERY_STRING} _REQUEST(=|\[|\%[0-9A-Z]{0,2}) # Return 403 Forbidden header and show the content of the root homepage RewriteRule .* index.php [F] # ## End - Rewrite rules to block out some common exploits. ## Begin - Custom redirects # # If you need to redirect some pages, or set a canonical non-www to # www redirect (or vice versa), place that code here. Ensure those # redirects use the correct RewriteRule syntax and the [R=301,L] flags. # ## End - Custom redirects ## # Uncomment following line if your webserver's URL # is not directly related to physical file paths. # Update Your Joomla! Directory (just / for root). ## # RewriteBase / ## Begin - Joomla! core SEF Section. # RewriteRule .* - [E=HTTP_AUTHORIZATION:%{HTTP:Authorization}] # # If the requested path and file is not /index.php and the request # has not already been internally rewritten to the index.php script RewriteCond %{REQUEST_URI} !^/index\.php # and the request is for something within the component folder, # or for the site root, or for an extensionless URL, or the # requested URL ends with one of the listed extensions RewriteCond %{REQUEST_URI} /component/|(/[^.]*|\.(php|html?|feed|pdf|vcf|raw))$ [NC] # and the requested path and file doesn't directly match a physical file RewriteCond %{REQUEST_FILENAME} !-f # and the requested path and file doesn't directly match a physical folder RewriteCond %{REQUEST_FILENAME} !-d # internally rewrite the request to the index.php script RewriteRule .* index.php [L] # ## End - Joomla! core SEF Section. Redirect 301 /index.html /index.php Redirect 301 /services /project Redirect 301 /projects/projects.html /project Redirect 301 /projects/project1.html /project Redirect 301 /projects/project2.html /project Redirect 301 /projects /project Redirect 301 /keypersonnel.html /about-agrin/keystaff Redirect 301 /cooperation.htm /about-agrin/intcoop Redirect 301 /member.html /about-agrin/memberships Redirect 301 /contact.html /contacts Redirect 301 /hr.htm /jobs Redirect 301 /index.php/404 /index.php

  Read the article

• Failed to unmount partitions

  - by msknapp

  I'm trying to install ubuntu from a pen drive. I have windows 7 installed already and want to keep that installation. I have a 3TB drive that has one 2TB partition on it, so the last 1TB is completely unused, which is where I want to install ubuntu. I started ubuntu in "try ubuntu" mode and then opened gparted, and then deleted the unused partition for the last third of my drive, then tried to install ubuntu. During the install, it asked me if I wanted to unmount the drives I already have The installer has detected that the following disks have mounted partitions: /dev/sda, /dev/sdb Do you want the installer to try to unmount the partitions on these disks before continuing? If you leave them mounted, you will not be able to create, delete, or resize partitions on these disks, but you may be able to install to existing partitions there. No, Yes I said no because I don't want to lose my windows 7 installation, nor any of that data. I wonder, if I had said yes above, would I have lost all the data on those drives? Anyways, I hit no and continued. I chose to install ubuntu alongside windows 7, and hit continue. A few minutes passed when this popup appeared: Failed to unmount partitions The installer needs to commit changes to partition tables, but cannot do so because the partitions on the following mount points could not be unmounted: /media/ubuntu/Three\ Terabyte Drive Terabyte\ DriveDrive Please close any applications using these mount points. Would you like the installer to try to unmount these partitions again? Go Back, Continue Why is this not working? What am I supposed to do? ========== Update: I went ahead and said yes, it can unmount those partitions. It finished installing Ubuntu, but now when i start my machine it just takes me to the grub rescue prompt. Seems like it broke something. What can I do now? =============== Results of fdisk -l: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00027e14 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 976771071 488282112 7 HPFS/NTFS/exFAT WARNING: GPT (GUID Partition Table) detected on '/dev/sdb'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdb: 3000.6 GB, 3000592982016 bytes 255 heads, 63 sectors/track, 364801 cylinders, total 5860533168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 4294967295 2147483647+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdc: 16.0 GB, 16008609792 bytes 255 heads, 63 sectors/track, 1946 cylinders, total 31266816 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 * 32 31266815 15633392 c W95 FAT32 (LBA) Disk /dev/sdd: 999.5 GB, 999501594624 bytes 255 heads, 63 sectors/track, 121515 cylinders, total 1952151552 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002ae3f Device Boot Start End Blocks Id System /dev/sdd1 2048 1952151551 976074752 7 HPFS/NTFS/exFAT

  Read the article

• ????????????????? Oracle Solaris ??? - Solaris 11 ????

  - by kazun

  ???????????????? OS ????????????????????? 20 ??????????????????? Solaris?????????????????????? OS????????????????????????Solaris ???????????????????? ??????Solaris ?????????????? 4 ????????????????????? Oracle Solaris 11 ??????????????? [????????????]???? ?(????????????? ???)???? ?(??????????????)???? ?(????????)???? ?(?????????????????)(50??) Oracle Solaris 11 ??????? ???:Oracle Solaris 11??????? Solaris ??????????????????????????????????????????????Oracle Solaris 10 ?????????????????Oracle Solaris 11 ???Oracle Solaris ???????????????????????????????????????????????????????????????????????????????????Oracle Solaris ??????????????????????????Oracle Solaris ????????????????????????????????????????? ??:??????????????????????????????????????????????????????????????????????????????????Oracle Solaris 11 ????????????????????????????????????????????????????????????????????????????????????????????????Oracle Solaris 11 ????????????? ???:Oracle Solaris 11 ????????????????????????????????????????????????????????????Oracle Solaris ??????????????????????Solaris ????????????????????????Oracle Solaris 11 ?????????????????????????????????????????????????????????????????????? Oracle Solaris 11 ??????????????? ??:???????????????????ZFS?????????????Oracle Solaris ???????????????????????????????????????IPS???????????????????????? ??:?????????????????????? OS ??????????????????????????????????????????????????????????????????? OS ????? Oracle Solaris 11 ??? ??:????????????????????????????????????????????????? Oracle Solaris 11 ???????????????????????????????????????????????????????? ??:????????????????????Solaris Trusted Extensions ? Solaris ????????????Privilege ????????????????????????????????Solaris 10 ???????????????????? ??:UNIX ?????????????????????????????????????Oracle Solaris 11 ??????????????????????????????????????????????????ZFS ??????????????????????????????????????????????????Oracle Solaris ?????????????????????????????????? ???:Oracle Solaris ????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????Oracle Solaris 11 ??????????????????????????????????????????????????? ?????????????Oracle Solaris 11 ??:Oracle Solaris ?????????????????????????????????????????????????????????????????? ZFS ?????????????????????????????????????????????? ??:?????????????????????????????????????????????????????????????????????Oracle Solaris ??????????????????????? ??:DTrace ????????????????????????????????????????????????????????????? ??:???????????????????????????????????????????????????????????????????????????????????????? ???:?????????????????????????????????????????????????????????????????????????Solaris ???????????????????????????????????????????????????????????????????????????? ??:?????????????????? Solaris 10 ?????????????????????????????????????? ???:ISV ??????????????????????????????? ????????????????? T4 ??????????????? T ?????? 5 ???????????????????????????????????? CPU ?????????????????? OS ? Solaris ??????????????????????????????????????????????? ??:???????????????? OS ???? Solaris ???????????????????????????????????????????????????? Oracle Solaris ????????? ??:???????????????????????????????????????????????????????????????????????????????????????? ZFS ?????????????????????????ZFS ??????????????????????????????????????? ???:Linux ??????????????????????????Solaris 11 ?????????????????????? GNU ????????????????????????????Solaris ?????????(Oracle Solaris Studio)????????????? Oracle Solaris Studio ?Linux??????????????Linux ??????????? Solaris ????????????????Linux ? Oracle Solaris Studio ?????????????????????????? Solaris ??????????????????? ??:??????????????????????????????????????????????????????????????????????????????????????????????????????????????????BCP(??????)??????????????????? ??:???????? Solaris 11 ?????? IA Server ?????????????????????????????????????????????…???????????Windows ????????????????????? Oracle Virtual Box ????????? Oracle Solaris 11 ??????????? ??:???Oracle Solaris ????????(?)??????????????ZFS???DTrace?????????????????????????????????????Solaris ?????????????????????????????????????????????????????????????????????????????Solaris ????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ??:??? 3 ??????????????????????????????????????Oracle Solaris 11 ???????????? ??:???????????????????? OS ??????????????????????????Oracle Solaris 11 ???????????????????????????????????????????????????????????????? ???:???????????? Solaris ???????????????Solaris 10 ???? 6 ??????????????????????????????????Oracle Solaris ?????????????????????????????? ?????? Oracle Solaris 10 Oracle Solaris 11

  Read the article

• Can't launch glassfish on ec2 - can't open port

  - by orange80

  I'm trying to start glassfish on an EBS-based AMI of Ubuntu 10.04 64-bit. I have used glassfish on non-ec2 servers with no problems, but on ec2 I get this message: $ sudo -u glassfish bin/asadmin start-domain domain1 There is a process already using the admin port 4848 -- it probably is another instance of a GlassFish server. Command start-domain failed. I know that ec2 has requires that firewall rules be modified using ec2-authorize to let outside traffic thru the firewall, as I had to do to make ssh work. This still doesn't explain the port error when all I'm trying to do is start glassfish so I can try $ wget localhost:8080and make sure it's working. This is very frustrating and I'd really appreciate any help. Thanks. FINAL UPDATE: Sorry if you came here looking for answers. I never figured out what was causing the problem. I created another fresh instance, installed the same stuff, and Glassfish worked perfectly. Something obviously got boned during installation, but I have no idea what. I guess it will remain a mystery. UPDATE: Here's what I get from netstat: # netstat -nuptl Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 462/sshd tcp6 0 0 :::22 :::* LISTEN 462/sshd udp 0 0 0.0.0.0:5353 0.0.0.0:* 483/avahi-daemon: r udp 0 0 0.0.0.0:1194 0.0.0.0:* 589/openvpn udp 0 0 0.0.0.0:37940 0.0.0.0:* 483/avahi-daemon: r udp 0 0 0.0.0.0:68 0.0.0.0:* 377/dhclient3 UPDATE: One more thing... I know that the "net.ipv6.bindv6only" kernel option can cause problems with java networking, so I did set this: # sysctl -w net.ipv6.bindv6only=0 UPDATE: I also verified that it has nothing at all to do with the port number (4848). As you can see here, when I changed the admin-listener port in domain.xml to 4949, I get a similar message: # sudo -u glassfish bin/asadmin start-domain domain1 There is a process already using the admin port 4949 -- it probably is another instance of a GlassFish server. Command start-domain failed. UPDATE: Here are the contents of /etc/hosts: 127.0.0.1 localhost # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts I should mention that I have another Ubuntu Lucid 10.04 64-bit slice that is NOT hosted on ec2, and set it up the exact same way with no problems whatsoever. Also server.log doesn't offer much insight either: # cat ./server.log Nov 20, 2010 8:46:49 AM com.sun.enterprise.admin.launcher.GFLauncherLogger info INFO: JVM invocation command line: /usr/lib/jvm/java-6-sun-1.6.0.22/bin/java -cp /opt/glassfishv3/glassfish/modules/glassfish.jar -XX:+UnlockDiagnosticVMOptions -XX:MaxPermSize=192m -XX:NewRatio=2 -XX:+LogVMOutput -XX:LogFile=/opt/glassfishv3/glassfish/domains/domain1/logs/jvm.log -Xmx512m -client -javaagent:/opt/glassfishv3/glassfish/lib/monitor/btrace-agent.jar=unsafe=true,noServer=true -Dosgi.shell.telnet.maxconn=1 -Djdbc.drivers=org.apache.derby.jdbc.ClientDriver -Dfelix.fileinstall.dir=/opt/glassfishv3/glassfish/modules/autostart/ -Djavax.net.ssl.keyStore=/opt/glassfishv3/glassfish/domains/domain1/config/keystore.jks -Dosgi.shell.telnet.port=6666 -Djava.security.policy=/opt/glassfishv3/glassfish/domains/domain1/config/server.policy -Dfelix.fileinstall.poll=5000 -Dcom.sun.aas.instanceRoot=/opt/glassfishv3/glassfish/domains/domain1 -Dcom.sun.enterprise.config.config_environment_factory_class=com.sun.enterprise.config.serverbeans.AppserverConfigEnvironmentFactory -Dosgi.shell.telnet.ip=127.0.0.1 -Djava.endorsed.dirs=/opt/glassfishv3/glassfish/modules/endorsed:/opt/glassfishv3/glassfish/lib/endorsed -Dcom.sun.aas.installRoot=/opt/glassfishv3/glassfish -Djava.ext.dirs=/usr/lib/jvm/java-6-sun-1.6.0.22/lib/ext:/usr/lib/jvm/java-6-sun-1.6.0.22/jre/lib/ext:/opt/glassfishv3/glassfish/domains/domain1/lib/ext -Dfelix.fileinstall.bundles.new.start=true -Djavax.net.ssl.trustStore=/opt/glassfishv3/glassfish/domains/domain1/config/cacerts.jks -Dcom.sun.enterprise.security.httpsOutboundKeyAlias=s1as -Djava.security.auth.login.config=/opt/glassfishv3/glassfish/domains/domain1/config/login.conf -DANTLR_USE_DIRECT_CLASS_LOADING=true -Dfelix.fileinstall.debug=1 -Dorg.glassfish.web.rfc2109_cookie_names_enforced=false -Djava.library.path=/opt/glassfishv3/glassfish/lib:/usr/lib/jvm/java-6-sun-1.6.0.22/jre/lib/amd64/server:/usr/lib/jvm/java-6-sun-1.6.0.22/jre/lib/amd64:/usr/lib/jvm/java-6-sun-1.6.0.22/lib/amd64:/usr/java/packages/lib/amd64:/usr/lib64:/lib64:/lib:/usr/lib com.sun.enterprise.glassfish.bootstrap.ASMain -domainname domain1 -asadmin-args start-domain,,,domain1 -instancename server -verbose false -debug false -asadmin-classpath /opt/glassfishv3/glassfish/modules/admin-cli.jar -asadmin-classname com.sun.enterprise.admin.cli.AsadminMain -upgrade false -domaindir /opt/glassfishv3/glassfish/domains/domain1 -read-stdin true

  Read the article

• Cannot ping Localhost so I can't shutdown Tomcat

  - by gav

  Hi, I installed Tomcat 6 using the tar-ball via wget. Startup of the server is fine but on shutdown I get a timeout exception. root@88:/usr/local/tomcat/logs# /usr/local/tomcat/bin/shutdown.sh Using CATALINA_BASE: /usr/local/tomcat Using CATALINA_HOME: /usr/local/tomcat Using CATALINA_TMPDIR: /usr/local/tomcat/temp Using JRE_HOME: /usr Using CLASSPATH: /usr/local/tomcat/bin/bootstrap.jar 30-Mar-2010 17:33:41 org.apache.catalina.startup.Catalina stopServer SEVERE: Catalina.stop: java.net.ConnectException: Connection timed out at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) ... I read that this might be because I have a firewall blocking incoming connections on the shutdown port (8005). I have a default Ubuntu 9.04 installation running on a VPS with no rules in my iptables. How can I tell if that port is blocked? How can I check that the server is listening for connections on 8005? Bizarrely pinging localhost or the IP of my server fails from the server itself, whereas pinging the IP of my server from another machine succeeds. -------- EDIT -------- (In reply to Davey) Thanks for all the tips and suggestions! netstat -nlp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:8005 0.0.0.0:* LISTEN 9611/java tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN 28505/mysqld tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN 9611/java tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN ... So we can see that tomcat is listening, I just don't seem to be able to reach it. root@88:/usr/local/tomcat# telnet localhost 8005 Trying 127.0.0.1... Trying to telnet to the port Hangs indefinitely. I have no rules in my iptables so I don't think it's a firewall thing. root@88:/usr/local/tomcat# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination This is the contents of /etc/hosts 127.0.0.1 localhost.localdomain localhost # Auto-generated hostname. Please do not remove this comment. 88.198.31.14 88.198.31.14 88 88 But I still can't ping localhost... do I need to check a loopback device is enabled properly or something? (I'm unsure how to do that if you do say yes :)). root@88:/usr/local/tomcat# ping localhost PING localhost (127.0.0.1) 56(84) bytes of data. --- localhost ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 5999ms Trying to find out what the loop back is configured as; root@88:~# ifconfig lo lo Link encap:Local Loopback LOOPBACK MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) SOLUTION THANKS TO DAVEY I needed to bring up the interface (Not sure why it wasn't running). ifconfig lo up did the trick. root@88:~# ifconfig lo up root@88:~# ifconfig lo lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@88:~# ping localhost PING localhost.localdomain (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost.localdomain (127.0.0.1): icmp_seq=1 ttl=64 time=0.025 ms Thanks again, Gav

  Read the article

• jQuery, jQuery UI, and Dual Licensed Plugins (Dual Licensing)

  - by John Hartsock

  OK I have read many posts regarding Dual Licensing using MIT and GPL licenses. But Im curious still, as the wording seems to be inclusive. Many of the Dual Licenses state that the software is licensed using "MIT AND GPL". The "AND" is what confuses me. It seems to me that the word "AND" in the terms, means you will be licensing the product using both licenses. Most of the posts, here on stackoverflow, state that you can license the software using one "OR" the other. JQuery specifically states "OR", whereas JQuery UI specifically States "AND". Another Instance of the "AND" would be JQGrid. Im not a lawyer but, it seems to me that a legal interpretation of this would state that use of the software would mean that your using the software under both licenses. Has anyone who has contacted a lawyer gotten clarification or a definitive answer as to what is true? Can you use Dual licensed software products that state "AND" in the terms of agreement under either license? EDITED: Guys here is specifically what Im talking about on jquery.org/license you see the following stated: You may use any jQuery project under the terms of either the MIT License or the GNU General Public License (GPL) Version 2 but in the header of Jquery's and Jquery UI library you see this: * Dual licensed under the MIT and GPL licenses. * http://docs.jquery.com/License The site says MIT or GPL but the license statement in the software says MIT and GPL.

  Read the article

• Xdebug configuration with PHP fastcgi and eclipse?

  - by mac

  I have been using eclipse-pdt in conjunction with xdebug and apache without problems, for over one year. Things worked flawlessly and I could do all the interactive debugging I wanted from within eclipse (using my own machine as a server). Now I switched from apache to nginx (and therefore PHP runs now not as an Apache service but as fast-cgi) and I can't find a way to configure eclipse to work nicely with xdebug. I am neither sure if the problem is with xdebug or with eclipse (or both) to be sure. In the eclipse configuration I already changed the reference to the PHP configuration file to /etc/php5/cli/php.ini. Attempts with php.ini version 1 With the following php.ini file zend_extension=/usr/lib/php5/20060613/xdebug.so I see that xdebug is working (for example if I do a var_dump() I get the xdebug version of it, not the plain PHP one) I can't have the interactive debugging from eclipse: the browser opens up and loads the page completely with the typical URL containing ...?XDEBUG_SESSION_START=ECLIPSE_DBGP&KEY=..., but the program execution does not stop at breakpoints In the bottom-right corner of eclipse I see a suspicious message: *"Launching =put_the_name_of_my_project_here=: 57%"* that alternates with the "refreshing workspace" one. Attempts with php.ini version 2 If I use this other version of the file (which is what it worked until I switched to nginx): zend_extension=/usr/lib/php5/20060613/xdebug.so xdebug.remote_enable=On xdebug.remote_autostart=On xdebug.remote_handler=dbgp xdebug.remote_host=localhost xdebug.remote_port=9000 xdebug.remote_mode=req I can't access any page of my sites at all. Any help or suggestion appreciated, thank you in advance for your time! PS: Additional data on my machine: - OS: GNU/Linux - Ubuntu 9.10 64 bit. - PHP: 5.2.10-2ubuntu6.3 with Suhosin-Patch 0.9.7; Zend Engine v2.2.0, Copyright (c) 1998-2009 Zend Technologies with Xdebug v2.0.4 - Eclipse: see screenshot.

  Read the article

• Emacs 23.1 make error 139 in Mac OS X 10.6.3

  - by penyuan

  When I try to compile GNU Emacs 23.1 on my machine with Mac OS X 10.6.3 I repeatedly get the following ending: Directories: /src/emacs-23.1/lisp/. /src/emacs-23.1/lisp/./calc /src/emacs-23.1/lisp/./calendar /src/emacs-23.1/lisp/./emacs-lisp /src/emacs-23.1/lisp/./emulation /src/emacs-23.1/lisp/./erc /src/emacs-23.1/lisp/./eshell /src/emacs-23.1/lisp/./gnus /src/emacs-23.1/lisp/./international /src/emacs-23.1/lisp/./language /src/emacs-23.1/lisp/./mail /src/emacs-23.1/lisp/./mh-e /src/emacs-23.1/lisp/./net /src/emacs-23.1/lisp/./nxml /src/emacs-23.1/lisp/./org /src/emacs-23.1/lisp/./play /src/emacs-23.1/lisp/./progmodes /src/emacs-23.1/lisp/./textmodes /src/emacs-23.1/lisp/./url /bin/sh: line 1: 69491 Segmentation fault EMACSLOADPATH=/src/emacs-23.1/lisp LC_ALL=C ../src/bootstrap-emacs -batch --no-site-file --multibyte -l autoload --eval '(setq generated-autoload-file "/src/emacs-23.1/lisp/loaddefs.el")' -f batch-update-autoloads $wins make[2]: *** [autoloads] Error 139 make[1]: *** [/src/emacs-23.1/src/../lisp/loaddefs.el] Error 2 make: *** [src] Error 2 Does anyone know what this means and what I could do to resolve the issue? By the way, here is my ./configure settings: ./configure --prefix=/usr/local --x-includes=/usr/X11/include --x-libraries=/usr/X11/lib --with-x I've tried to compile both with and without X with no success.

  Read the article

• Examples of localization in Perl using gettext and Locale::TextDomain, with fallback if Locale::Text

  - by Jakub Narebski

  The "On the state of i18n in Perl" blog post from 26 April 2009 recommends using Locale::TextDomain module from libintl-perl distribution for l10n / i18n in Perl. Besides I have to use gettext anyway, and gettext support in Locale::Messages / Locale::TextDomain is more natural than in gettext emulation in Locale::Maketext. The subsection "15.5.18 Perl" in chapter "15 Other Programming Languages" in GNU gettext manual says: Portability The libintl-perl package is platform independent but is not part of the Perl core. The programmer is responsible for providing a dummy implementation of the required functions if the package is not installed on the target system. However neither of two examples in examples/hello-perl in gettext sources (one using lower level Locale::Messages, one using higher level Locale::TextDomain) includes detecting if the package is installed on the target system, and providing dummy implementation if it is not. What is complicating matter (with respect to detecting if package is installed or not) is the following fragment of Locale::TextDomain manpage: SYNOPSIS use Locale::TextDomain ('my-package', @locale_dirs); use Locale::TextDomain qw (my-package); USAGE It is crucial to remember that you use Locale::TextDomain(3) as specified in the section "SYNOPSIS", that means you have to use it, not require it. The module behaves quite differently compared to other modules. Could you please tell me how one should detect if libintl-perl is present on target system, and how to provide dummy fallthrough implementation if it is not installed? Or give examples of programs / modules which do this?

  Read the article

• How do I remove accents from characters in a PHP string?

  - by georgebrock

  I'm attempting to remove accents from characters in PHP string as the first step to making the string usable in a URL. I'm using the following code: $input = "Fóø Bår"; setlocale(LC_ALL, "en_US.utf8"); $output = iconv("utf-8", "ascii//TRANSLIT", $input); print($output); The output I would expect would be something like this: F'oo Bar However, instead of the accented characters being transliterated they are replaced with question marks: F?? B?r Everything I can find online indicates that setting the locale will fix this problem, however I'm already doing this. I've already checked the following details: The locale I am setting is supported by the server (included in the list produced by locale -a) The source and target encodings (UTF-8 and ASCII) are supported by the server's version of iconv (included in the list produced by iconv -l) The input string is UTF-8 encoded (verified using PHP's mb_check_encoding function, as suggested in the answer by mercator) The call to setlocale is successful (it returns 'en_US.utf8' rather than FALSE) The cause of the problem: The server is using the wrong implementation of iconv. It has the glibc version instead of the required libiconv version. Note that the iconv function on some systems may not work as you expect. In such case, it'd be a good idea to install the GNU libiconv library. It will most likely end up with more consistent results. – PHP manual's introduction to iconv Details about the iconv implementation that is used by PHP are included in the output of the phpinfo function. (I'm not able to re-compile PHP with the correct iconv library on the server I'm working with for this project so the answer I've accepted below is the one that was most useful for removing accents without iconv support.)

  Read the article

• Converting from CVS to SVN to Hg, does 'hg convert' require pointing to an SVN checkout or just a re

  - by Terry

  As part of migrating full CVS history to Hg, I've used cvs2svn to create an SVN repo in a local directory. It's first level directory structure is: 2010-04-21 09:39 AM <DIR> . 2010-04-21 09:39 AM <DIR> .. 2010-04-21 09:39 AM <DIR> locks 2010-04-21 09:39 AM <DIR> hooks 2010-04-21 09:39 AM <DIR> conf 2010-04-21 09:39 AM 229 README.txt 2010-04-21 11:45 AM <DIR> db 2010-04-21 09:39 AM 2 format 2 File(s) 231 bytes After setting up hg and the convert extension and attempting the convert, I get the following on convert: C:\>hg convert file://localhost/Users/terry/Desktop/repoSVN assuming destination repoSVN-hg initializing destination repoSVN-hg repository file://localhost/Users/terry/Desktop/repoSVN does not look like a CVS checkout file://localhost/Users/terry/Desktop/repoSVN does not look like a Git repo file://localhost/Users/terry/Desktop/repoSVN does not look like a Subversion repo file://localhost/Users/terry/Desktop/repoSVN is not a local Mercurial repo file://localhost/Users/terry/Desktop/repoSVN does not look like a darcs repo file://localhost/Users/terry/Desktop/repoSVN does not look like a monotone repo file://localhost/Users/terry/Desktop/repoSVN does not look like a GNU Arch repo file://localhost/Users/terry/Desktop/repoSVN does not look like a Bazaar repo file://localhost/Users/terry/Desktop/repoSVN does not look like a P4 repo abort: file://localhost/Users/terry/Desktop/repoSVN: missing or unsupported repository I have TortoiseHg installed. For info, hg version reports: Mercurial Distributed SCM (version 1.4.3) This version of Mercurial seems to have some svn bindings if library.zip in the install is to be believed. Do I need to do a checkout and point hg convert to it for this to work properly?

  Read the article

• New at Python: GLPK not building properly / Python ImportError

  - by Merjit

  This is a beginner question, and a follow-up to this one, where I was pointed to GLPK. I'm trying to get PyGLPK, a Python binding for the GNU Linear Programming Kit up and running, but no matter what I do, I can't seem to build and install GLPK so that Python finds it correctly. This comes after running ./configure, make, and sudo make install on the GLPK libraries, and following the instructions for PyGLPK. Specifically, here is the error I get: >>> import glpk Traceback (most recent call last): File "<stdin>", line 1, in <module> ImportError: dlopen(/Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site- packages/glpk.so, 2): Symbol not found: __glp_lpx_print_ips Referenced from: /Library/Frameworks/Python.framework/Versions/2.6/lib/python2.6/site-packages/glpk.so Expected in: dynamic lookup I assume that something isn't linking to somewhere else, and that it probably has something to do with paths and environment variables. However, here's where my abilities in the shell fail, and I'm at a loss over what to do next. Again, there is probably a simple answer to this, but I haven't had any luck with Google using the terminology I know.

  Read the article

• org.smslib port in use exception

  - by danar jabbar

  I am trying to create web application to send sms by gsm modem in JSP first I put destination mobile number and sms text in url and get by request.getparameter and first message sent with no problem but when send a message again by referenshing the same page i get this exception: org.smslib.GatewayException: Comm library exception: java.lang.RuntimeException: gnu.io.PortInUseException: org.smslib at org.smslib.modem.SerialModemDriver.connectPort(SerialModemDriver.java:102) at org.smslib.modem.AModemDriver.connect(AModemDriver.java:114) at org.smslib.modem.ModemGateway.startGateway(ModemGateway.java:189) at org.smslib.Service$1Starter.run(Service.java:276) I tried to stop gateway and stop service but no hope My code: public boolean sendMessage(String strMobileNo,String strSMSText) { try { OutboundMessage outboundMessage=new OutboundMessage(); SMS message=new SMS(); SerialModemGateway gateway = new SerialModemGateway("modem.com1", "COM12", 9600, "Huawie", "EF200"); gateway.setInbound(true); gateway.setOutbound(true); gateway.setSimPin("0000"); gateway.setSmscNumber("+9647701144010"); Service.getInstance().setOutboundMessageNotification(message); Service.getInstance().addGateway(gateway); Service.getInstance().startService(); outboundMessage.setText(strSMSText); outboundMessage.setRecipient(strMobileNo); outboundMessage.setEncoding(Message.MessageEncodings.ENCUCS2); //outboundMessage.setDeliveryDelay(5000); Service.getInstance().sendMessage(outboundMessage); System.out.println(outboundMessage); gateway.stopGateway(); Service.getInstance().stopService(); Thread.sleep(10000); return true; } catch (Exception e) { e.printStackTrace(); return false; } }

  Read the article

• Error C2451: Illegal conditional expression of type 'UnaryOp<E1, Op>' in ostream - visual studio 9

  - by Steven Hill

  I am getting a repeated error with VS 9. The code compiles under GNU C++, but I want debug with the VS IDE. Any idea what could be causing this error. Error 13 error C2451: conditional expression of type 'UnaryOp' is illegal \Microsoft Visual Studio 9.0\VC\include\ostream 512 //unary constraint template class UnaryOp : public Constraint { public: const E1& e1; UnaryOp(const E1& _e1); bool Satisfiable() const; Bool SatisfiableAux() const; void Print (std::ostream& os) const; UnaryOp* clone () const; //operator bool () const { return true; } }; template std::ostream& operator<<(std::ostream& os, const UnaryOp& unop); UnaryOp code that uses ostream: template INLINE void UnaryOp::Print (std::ostream& os) const { os << *this; } template INLINE std::ostream& operator<<(std::ostream& os, const UnaryOp& unop) { return os << Op::name << unop.e1; } ostream line with error: _Myt& __CLR_OR_THIS_CALL put(_Elem _Ch) { // insert a character ios_base::iostate _State = ios_base::goodbit; const sentry _Ok(*this); 512 if (!_Ok) _State |= ios_base::badbit; else { // state okay, insert character _TRY_IO_BEGIN

  Read the article

• "jpeglib.h: No such file or directory" ghostscript port in OPENBSD

  - by holms

  Hello I have a problem with compiling a ghostscript from ports in openbsd 4.7. SO i have jpeg-7 installed, I have latest port tree for obsd4.7. ===> Building for ghostscript-8.63p11 mkdir -p /usr/ports/pobj/ghostscript-8.63p11/ghostscript-8.63/obj gmake LDFLAGS='-L/usr/local/lib -shared' GS_XE=./obj/../obj/libgs.so.11.0 STDIO_IMPLEMENTATION=c DISPLAY_DEV=./obj/../obj/display.dev BINDIR=./obj/../obj GLGENDIR=./obj/../obj GLOBJDIR=./obj/../obj PSGENDIR=./obj/../obj PSOBJDIR=./obj/../obj CFLAGS='-O2 -fno-reorder-blocks -fno-reorder-functions -fomit-frame-pointer -march=i386 -fPIC -Wall -Wstrict-prototypes -Wmissing-declarations -Wmissing-prototypes -fno-builtin -fno-common -DGS_DEVS_SHARED -DGS_DEVS_SHARED_DIR=\"/usr/local/lib/ghostscript/8.63\"' prefix=/usr/local ./obj/../obj/gsc gmake[1]: Entering directory `/usr/ports/pobj/ghostscript-8.63p11/ghostscript-8.63' cc -I./obj/../obj -I./src -DHAVE_MKSTEMP -O2 -fno-reorder-blocks -fno-reorder-functions -fomit-frame-pointer -march=i386 -fPIC -Wall -Wstrict-prototypes -Wmissing-declarations -Wmissing-prototypes -fno-builtin -fno-common -DGS_DEVS_SHARED -DGS_DEVS_SHARED_DIR=\"/usr/local/lib/ghostscript/8.63\" -DGX_COLOR_INDEX_TYPE='unsigned long long' -o ./obj/../obj/sdctc.o -c ./src/sdctc.c In file included from src/sdctc.c:17: obj/jpeglib_.h:1:21: jpeglib.h: No such file or directory In file included from src/sdctc.c:19: src/sdct.h:58: error: field `err' has incomplete type src/sdct.h:70: error: field `err' has incomplete type src/sdct.h:72: error: field `cinfo' has incomplete type src/sdct.h:73: error: field `destination' has incomplete type src/sdct.h:84: error: field `err' has incomplete type src/sdct.h:87: error: field `dinfo' has incomplete type src/sdct.h:88: error: field `source' has incomplete type gmake[1]: *** [obj/../obj/sdctc.o] Error 1 gmake[1]: Leaving directory `/usr/ports/pobj/ghostscript-8.63p11/ghostscript-8.63' gmake: *** [so] Error 2 *** Error code 2 Stop in /usr/ports/print/ghostscript/gnu (line 2225 of /usr/ports/infrastructure/mk/bsd.port.mk). I tried to place one more param in CFLAGS in Makefile with value "-I/usr/local" but no luck =( People in irc [freenode server, #openbsd channel] refuses give any help for ports at all, and even more - because this is 4.7 unstable version. I have my reasons to use this version and ports believe me =) CFLAGS+= -DSYS_TYPES_HAS_STDINT_TYPES \ -I${LOCALBASE}/include \ -I${LOCALBASE}/include/ijs \ -I${LOCALBASE}/include/libpng \

  Read the article

• Shell script to emulate warnings-as-errors?

  - by talkaboutquality

  Some compilers let you set warnings as errors, so that you'll never leave any compiler warnings behind, because if you do, the code won't build. This is a Good Thing. Unfortunately, some compilers don't have a flag for warnings-as-errors. I need to write a shell script or wrapper that provides the feature. Presumably it parses the compilation console output and returns failure if there were any compiler warnings (or errors), and success otherwise. "Failure" also means (I think) that object code should not be produced. What's the shortest, simplest UNIX/Linux shell script you can write that meets the explicit requirements above, as well as the following implicit requirements of otherwise behaving just like the compiler: - accepts all flags, options, arguments - supports redirection of stdout and stderr - produces object code and links as directed Key words: elegant, meets all requirements. Extra credit: easy to incorporate into a GNU make file. Thanks for your help. === Clues === This solution to a different problem, using shell functions (?), Append text to stderr redirects in bash, might figure in. Wonder how to invite litb's friend "who knows bash quite well" to address my question? === Answer status === Thanks to Charlie Martin for the short answer, but that, unfortunately, is what I started out with. A while back I used that, released it for office use, and, within a few hours, had its most severe drawback pointed out to me: it will PASS a compilation with no warnings, but only errors. That's really bad because then we're delivering object code that the compiler is sure won't work. The simple solution also doesn't meet the other requirements listed. Thanks to Adam Rosenfield for the shorthand, and Chris Dodd for introducing pipefail to the solution. Chris' answer looks closest, because I think the pipefail should ensure that if compilation actually fails on error, that we'll get failure as we should. Chris, does pipefail work in all shells? And have any ideas on the rest of the implicit requirements listed above?

  Read the article

• How can I enable PHP5 for a site? Having problems with every single method.

  - by user347662

  I'm working on a client site that is hosted on someone's DIY Debian Linux server [Apache/1.3.33 (Debian GNU/Linux)], and I'm trying to install a script that requires PHP5. By default, the server parses .php files with PHP 4.3.10-22, which is configured at /etc/php4/apache/php.ini, according to phpinfo(). On the server I can see a config directory for PHP5 adjacent to the PHP4 directory: /etc/php5.0/apache2/php.ini. I have tried multiple methods to enable PHP5 for the document root where the site's files are hosted, including all available methods mentioned here. By far, the most common suggestion I've found is to add one or both of the following lines to the site's .htaccess file: AddHandler application/x-httpd-php5 .php AddType application/x-httpd-php5 .php Trouble is, when either or both of those lines are present, the site forces my browser to download any .php files requested, without parsing the PHP at all. All of the other methods mentioned in the above article cause a 500 Internal Server Error. There is no hosting control panel I can access in a browser to enable PHP5 for the site, but I do have shell access. When I asked the server administrator about this issue, he encouraged me to search for the answer on Google. Where could I begin to troubleshoot this issue? Are there ways to test or verify the server's specific PHP5 installation and configuration, using the command line or some other method? Do you have other suggestions to enable PHP5?

  Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >