Search Results

Search found 3171 results on 127 pages for 'manual manuel'.

Page 91/127 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• SQL Server Database In Single User Mode after Failover

  - by jlichauc

  Here is a weird situation we experienced with a SQL Server 2008 Database Mirroring Failover. We have a pair of mirrored databases running in high-availability mode and both the principal and mirror showed as synchronized. As part of some maintenance I triggered a manual failover of the principal to the mirror. However after the failover the principal was now in single-user mode instead of the expected "Principal/Synchronized" state we usually get. The database had been in multi-user mode on the previous principal before this had happened. We ended up stopping all applications, restarting the SQL Server instances, and executing "ALTER DATABASE ... SET MULTI_USER" to bring the database back to the expected "Principal/Synchronized" state in a multi-user mode. Question. Does anyone know where SQL Server stores information about whether a database should be in single-user mode or not? I'm wondering if there is some system database or table that has this setting recorded somewhere. In particular we had an incident once with the database on the original principal (the one I was failing over to) where when trying to detach the database it was put into single-user mode. I'm wondering if that setting is cached somewhere and is the reason that SQL Server put it back into single-user mode after a failover.

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• PC can't detect second RAM installed

  - by kulwinder

  I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

  Read the article

• IP-dependent local port-forwarding on Linux

  - by chronos

  I have configured my server's sshd to listen on a non-standard port 42. However, at work I am behind a firewall/proxy, which only allow outgoing connections to ports 21, 22, 80 and 443. Consequently, I cannot ssh to my server from work, which is bad. I do not want to return sshd to port 22. The idea is this: on my server, locally forward port 22 to port 42 if source IP is matching the external IP of my work's network. For clarity, let us assume that my server's IP is 169.1.1.1 (on eth1), and my work external IP is 169.250.250.250. For all IPs different from 169.250.250.250, my server should respond with an expected 'connection refused', as it does for a non-listening port. I'm very new to iptables. I have briefly looked through the long iptables manual and these related / relevant questions: http://serverfault.com/questions/57872/iptables-question-forwarding-port-x-to-an-ssh-port-of-different-machine-on-the-n http://serverfault.com/questions/140622/how-can-i-port-forward-with-iptables However, those questions deal with more complicated several-host scenarios, and it is not clear to me which tables and chains I should use for local port-forwarding, and if I should have 2 rules (for "question" and "answer" packets), or only 1 rule for "question" packets. So far I have only enabled forwarding via sysctl. I will start testing solutions tomorrow, and will appreciate pointers or maybe case-specific examples for implementing my simple scenario. Is the draft solution below correct? iptables -A INPUT [-m state] [-i eth1] --source 169.250.250.250 -p tcp --destination 169.1.1.1:42 --dport 22 --state NEW,ESTABLISHED,RELATED -j ACCEPT Should I use the mangle table instead of filter? And/or FORWARD chain instead of INPUT?

  Read the article

• How to auto mark tape as free in DPM 2012?

  - by Massimo

  I have a backup server running System Center Data Protection Manager 2012, connected to a couple of tape drives (no library). I also have, of course, some tapes. Tape rotation is manual. The tape have been used before, by DPM itself (but the server has been completely rebuilt) and by other backup softwares; they are not emtpy. But they contain no data that DPM knows and/or wants to preserve, so they can be marked as free without having to run forcefreetape.ps1. When a tape is placed into the drive, it is required to perform an inventory, have it recognized as an imported tape and then mark it as free; otherwise DPM will simply refuse to use it. How can I tell DPM to automatically treat those imported tapes as free? And, of course, I do not want to reuse real backup tapes if by chance they get put into the drives before their expiration date, so the solution should mark imported tapes as free, but should not do the same with real, non-expired tapes.

  Read the article

• HTTPS and Certification for dummies

  - by Poxy

  I had never used https on a site and now want to try it. I did some research, but not sure that I understood everything. Answers and corrections are greatly appreciated. Here we go: To use https I need to generate ‘private’ and ‘public’ keys for the web server I use. In my case it’s apache (manual: http://httpd.apache.org/docs/2.0/ssl/ssl_faq.html) Https protocol should be bind to port 443. Q: How to do it? Is it done by default? Where can I check configuration? Aplying https. Q: If I see https in browser does it mean that the data traffic on the page IS encrypted? Any form on the page would submit data via https? Though all the data gonna be encrypted, the browsers would still show ugly red messages. This is just because they do not know anything about my certificate. They have about a hundred certificates pre-installed but mine is not one of them, obviously. But the data IS encrypted by https. If I want browsers to recognize my certificate, I would need to have it signed by one of the certification authorities (ca) that has its certificate pre-installed (e.g. thawte, geotrust, rapidssl etc). UPD: To reed about ssl/tsl: The First Few Milliseconds of an HTTPS Connection, I found it very informative. Examples for PHP (openssl.org) of how to make use of ssl/tsl on the server side are published here.

  Read the article

• OpenLDAP replication fails, "syncrepl_entry: rid=666 be_modify failed (20)"

  - by Pavel

  I've configured a second host to replicate the main LDAP server via syncrepl in the slapd.conf: syncrepl rid=666 provider=ldaps://my-main-server.com type=refreshAndPersist searchBase="dc=Staff,dc=my-main-server,dc=com" filter="(objectClass=*)" scope=sub schemachecking=off bindmethod=simple binddn="cn=repadmin,dc=my-main-server,dc=com" credentials=mypassword When I restart slapd, it writes to /var/log/debug Jun 11 15:48:33 cluster-mn-04 slapd[29441]: @(#) $OpenLDAP: slapd 2.4.9 (Mar 31 2009 07:18:37) $ ^Ibuildd@yellow:/build/buildd/openldap2.3-2.4.9/debian/build/servers/slapd Jun 11 15:48:34 cluster-mn-04 slapd[29442]: slapd starting Jun 11 15:48:34 cluster-mn-04 slapd[29442]: null_callback : error code 0x14 Jun 11 15:48:34 cluster-mn-04 slapd[29442]: syncrepl_entry: rid=666 be_modify failed (20) Jun 11 15:48:34 cluster-mn-04 slapd[29442]: do_syncrepl: rid=666 quitting I've looked into the sources for the return code and found only #define LDAP_TYPE_OR_VALUE_EXISTS 0x14 in include/ldap.h. Anyway, I don't quite get what the error message means. Can you help me debugging this problem and figure out why the LDAP replication doesn't work? I've managed to put a "manual" copy via slapcat and slapadd into the database, but I'd like to sync automatically. UPDATE: "Solved" by removing /var/lib/ldap/* and re-importing the database with slapadd.

  Read the article

• Finding custom printer-specific options on *nix

  - by enbuyukfener

  Hey all, I have a printer set up using CUPS (FujiXerox Document Center 1100), it is named DC1100. There are capabilities of the printer that are not shows as options of the printer as listed by: lpoptions -l -d DC1100 The output is below: PrintoutMode/Printout Mode: Draft *Normal High Photo InputSlot/Media Source: Upper Lower MultiPurpose LargeCapacity Manual *Standard PageSize/Page Size: *Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement PageRegion/PageRegion: Letter A4 C5 C6 COM10 DL Executive Legal Monarch Statement STP_Brightness/Brightness: 0.00 0.02 0.04 [snip] 2.00 STP_Contrast/Contrast: 0.00 0.05 0.10 0.15 [snip] 4.00 STP_ColorCorrection/Color Correction: Accurate Bright Density [snip] Uncorrected STP_DitherAlgorithm/Dither Algorithm: Adaptive EvenTone Fast [snip] VeryFast STP_EnableDensity/Density Enable: *Disabled Enabled STP_Density/Density Value: 0.1 0.2 0.3 0.4 [snip] 8.0 STP_EnableGamma/Composite Gamma Enable: *Disabled Enabled STP_Gamma/Composite Gamma Value: 0.10 0.15 0.20 0.25 [snip] 4.00 STP_LinearContrast/Linear Contrast Adjustment: *False True STP_Duplex/Double-Sided Printing: DuplexNoTumble DuplexTumble *None Resolution/Rendering Resolution: *FromPrintoutMode 150x150dpi 300x300dpi 600x600dpi OutputType/Output Type: *FromPrintoutMode BlackAndWhite Grayscale STP_ImageType/Image Type: *FromPrintoutMode Photo Graphics LineArt None Text TextGraphics STP_Resolution/Resolution: *FromPrintoutMode 150dpi 300dpi 600dpi I am particularly looking for options for: "secure print" (possibly by setting a mode and setting a username) stapling hole punching Perhaps I need a vendor specific driver/PPD file? If so, any pointers as I have no idea where to look for one. I haven't been able to find one on the official site or on sites such as http://www.openprinting.org

  Read the article

• How do I register a service with Bonjour?

  - by Roman

  I am trying to start to use Bonjour. Here I found a manual how to register a service with Bonjour. The following is written there: The network services architecture in Bonjour includes an easy-to-use mechanism for publishing, discovering, and using IP-based services. Well let's see how to register a service. In the very beginning it is written: To publish a service, an application or device must register the service with a Multicast DNS responder But how?!?! First of all I do not know what is the Multicast DNS responder. Second, it is not written how do I do it. Where and what should I type? Should I use command line? Should I use some programming languages? What exactly should I type... Is there an easy way to start to use Bonjour? Well, it was emphasized several times how easy it should be to use it. But I cannot start to use it for several day. So, can anybody, pleas, help me with that?

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

  Read the article

• VGA to S-Video/Video converter showing mashed up picture.

  - by Matthijs Wessels

  Earlier I asked this question: *http://superuser.com/questions/132374/does-the-lenovo-t60p-vga-port-support-an-s-video-signal As a result I acquired the following item: http://cgi.ebay.nl/ws/eBayISAPI.dll?ViewItem&item=250588098582&ssPageName=ADME:B:EOIBSA:NL:1123 Yea I'm a cheapass... Anyway, it just arrived and now I am trying to get it to work... The manual is not very informative other than telling me, this is the vga in, this is the vga out, this is the s/video out etc. Plus it tells me the system should support the following resolutions@refresh rate: 640x480@60/72/75Hz 800x600@60/75Hz 1024x768@60Hz I can connect it to my laptop and then I connect the S/Video and the Video to my tv which only gives me a blurred image (like when you set your monitor to a resolution it doesn't support). The VGA out however works fine to my tft monitor. The are two switches on the converter. I think one switches between s/video and video and the other between PAL and NTSC. But alas, no combination seems to give a better picture (it does give a different picture). Can anyone help me to solve this problem? I have downloaded this program called powerstrip, but I have no idea how to use it and if it can even solve my problem... Thanks in advance. I use Windows XP on a Lenovo t60p and I try to connect it to a Philips 32PFL7403D/12 LCD TV from VGA to a converter to S-video or video.

  Read the article

• Memory modules not running at rated speeds.

  - by Wesley

  Hi all, I'm having some odd memory issues with my build. Here are my specs right now: QDI Superb 4 motherboard Intel Pentium 4 Northwood 2.4GHz (512KB L2, 533MHz FSB) 3x 256MB PC2100 DDR266 RAM 16MB NVIDIA TNT2 Pro AGP Seagate 80GB IDE HDD Generic USB 2.0 PCI Generic Modem PCI Bestec 250W PSU To be even more specific, here are the current brands and models of each module: Kingston KVR266X64C25/256 Samsung PC2100U-25331-Z SMART SM5643285D4N0CHM0H Supposedly, they are all PC2100 266MHz modules with a latency of 2.5. Looking in Speccy, the Kingston module is somehow running at a speed of PC2300 ~284MHz. I've never overclocked RAM at all as I don't know how to. However, when I first started the computer, I had the SMART module in place first and then reset the BIOS settings, including the integrated overclocking options. However, this still doesn't explain why the Kingston module runs at a higher speed than the SMART and Samsung module. Why is it like this? On a side note, where could I find the motherboard manual for the QDI Superb 4? Thanks in advance.

  Read the article

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Linux drivers for laser printer Konica Minolta Magicolor 4750DN

  - by user51166

  I would like to install the konica minolta magicolor 4750DN in Linux (debian 64 bits, I know it's not really supported but that's not the issue right now) but all the manual says is "put the CD rom in and copy the drivers and PPD file". However I did not get the CD ! On their "fantastic" internet site (...) there are only available drivers for Windows and Mac OSX. I tried to extract the ppd file from the .dmg file for MacOSX 10.7 but, if the PPD file works, a compiled file (only mac compiled, MACH 4 architectures says the "file" command) does not (obviously "cannot execute binary file", since I'm trying to run a Mac file on Linux). Is there anybody who has the same printer that could lend me the Linux drivers on the CD ROM ? Couldn't find them anywhere on the internet. Any way to execute a Mach (or BSD) binary file on Linux (I don't think is possible, although some "emulators" may exist). Thank you very much. I buyed this printer even because it was advertised as "Linux compatible", only to get this bad surprise. I would be grateful if you could help me solve this problem.

  Read the article

• Why Is Volume Shadow Copy Services stopping?

  - by David Mackintosh

  I am running Windows 7 Professional, 64-bit. I am running a backup-over-the-internet software client which depends on the Volume Shadow Copy Services running. Since I installed Service Pack 1 (or rather, didn't object when Windows Update forced Service Pack 1 on me) the backup service is failing to back everything up because VSC isn't running. Most of the time it fails to back up such noise as the Security Essentials database or the Messenger Live contact list -- stuff I really don't care about -- but I don't want to fall into the trap of accepting an Error-state backup as "normal". At the recommendation of the backup software, I have set the VSC service startup mode to be Automatic. When I look in the Event Log, System channel I can see at boot time: The Volume Shadow Copy service entered the running state. ...and then two or three minutes later: The Volume Shadow Copy service entered the stopped state. How do I figure out why VSC is stopping? At the suggestion of the backup vendor, I have already followed the suggestions from http://support.microsoft.com/default.aspx/kb/940184 net stop SENS net stop EventSystem net start EventSystem net start SENS net stop COMSysApp net stop SwPrv net stop VSS cd /d C:\Windows\system32 regsvr32 ole32.dll /s regsvr32 oleaut32.dll /s regsvr32 vss_ps.dll /s vssvc /register /s regsvr32 /i swprv.dll /s regsvr32 /i eventcls.dll /s regsvr32 es.dll /s regsvr32 stdprov.dll /s regsvr32 vssui.dll /s regsvr32 msxml.dll /s regsvr32 msxml3.dll /s regsvr32 msxml4.dll /s net start SwPrv net start VSS net start ProtectedStorage ...and per http://support.microsoft.com/kb/940184 I have deleted the key tree HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\EventSystem\{26c409cc-ae86-11d1-b616-00805fc79216}\Subscriptions I have also run chkdsk /F and chkdsk /R on both permanent hard disks. (I had a similar problem with another computer (same OS, same failure, same start point after SP1 install) but the problem went away when I forced Volume Shadow Copy Services to Automatic startup rather than Manual. I did not have to resort to following the Microsoft KB instructions.)

  Read the article

• Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• How to create Windows Vista/Windows 7 Startup disk or Rescue disk or system restore points on a CD?

  - by goldenmean

  Hello, I have two laptops, one having Windows-Vista home premium and other one having Windows-7 professional. Both versions of OS are OEM installs(pre-installed when I bought the laptop) and I do not have the Windows Installation disks for them. usually the installation disks provide a repair option in case one needs to repair/rescue a improper windows installation. But since I dont have the installation disks, I want to create rescue disks/startup disks for these. My questions are : 1] How to create a system rescue disk/startup disk on a CD from these two versions of Windows? 2] Doesn't the system restore points which Vista/Windows-7 create, cannot be created on a CD disk instead of hard-disk? 3] If I have a manual backup of my windows registry, in which I have exported all the registry to a file and I have that file on a CD, how to restore that registry back to the windows installation which might not be booting up properly due to bad registry problem. EDIT: 4]Is there any way to use these system restore points directly during bootup of the laptop, if windows does cannot boot properly due to problem. First laptop is HP Pavillion dv6646 and second one is Sony VAIO VCPEE series. thank you. -AD

  Read the article

• Troubleshooting wireless client-bridged networks between two DD-WRT routers?

  - by KronoS

  I recently purchased a Buffalo N600 wireless router which came with DD-WRT pre-installed. I want to take my old wireless router a Linksys WRT54GL, also with DD-WRT pre-installed, and use it as a wireless bridge for my HTPC and Blu-Ray Player in the other room. I other words, I'm trying to connect to WIRED networks via the wireless on the routers. I followed eactly the instruction from DD-WRT's manual for 'Client Bridged' however I'm still not able to connect to two routers correctly, when the encryption is enabled (WPA2-Personal Mixed) however I am able to connect the two routers when there is NO encryption. I've checked, double checked, and triple checked that EVERYTHING is the same on BOTH routers: Routers 1 & 2 Encryption: WPA2-Personal Mixed Wireless Mode: G-Only Wireless Channel: 6 Subnet Mask: 255.255.255.0 Subnet: 192.168.1.0/254 SSID: Krono$ Primary Router #1 (Buffalo N600) IP Address: 192.168.1.1 Firewall: Enables w/ defaults DCHP: Enabled as DHCP Server Secondary Router #2 (Linksys WRT54GL) IP Address: 192.168.1.2 Firewall: Disabled as per DD-WRT instructions I'm looking for any configurations that I may have missed, or settings that may need to happen in order for this work.

  Read the article

• Autologin 2 Windows users OR Login another user from the desktop

  - by fpdragon

  I'm using two windows users on my HTPC at the same time. One is just for watching videos and one for administration via remote. This setup is quite ideal for me since windows can handle multiple concurrent logins and the win "rdp concurrent hack" (Google). The problem is, I want both users to be logged in automatically when the pc was started. It shall be possible to watch tv and also the admin user shall be automatically logged in to start my scripts and other tasks, even if I haven't logged in via remote desktop manually. Later, when I want to admin my htpc I can just rdp connect the admin user without interrupting the video playback on the actual HTPC's screen and check my cleanup tasks, downloads, ... witch already executed for this admin user. But right now I found no solution to automatically login user A from a user B desktop and I also found no solution to autologin both users immediately at startup. As a workaround I have to fire up my other notebook machine and login one time with the remote user via rdp. From this time on the remote admin user is running concurrent with the main user in the background of the machine. The other workaround would be... after startup switch user from main user to admin user and then back again. But that also requires manual steps. I'm on a Windows 8 System right now but all infos for Win7 or XP would be also interesting. thanks a lot for all ideas. PS: just to prevent useless posts... don't tell me that only one user can be logged in to windows. ;)

  Read the article

• BackupExec 2012 File System Archiving - Access is denied to Remote Agent

  - by AllisZero

  Gentlemen, I've been struggling with a Trial version of Symantec Backup Exec 2012 for about a week now. It was installed as an upgrade to our 12.5 license, and the setup completed with no issues. The reason I upgraded is solely for the File System Archiving option as I'm working to reduce the amount of live data in my servers. Backups work A-Ok and I have followed the instructions in the Admin Manual to make sure I had filled all requirements. The account BE is running under is a member of the Local administrators group as required and has been added to the test share that I'm using to evaluate the archiving function. Testing the credentials in the job setup window always works fine, and I am able to add both regular and Admin$ shares to my Archive selection. However, every time I run the Archive job, I get the following message: https://dl.dropbox.com/u/59540229/BEXec.png I've already tried to troubleshoot DNS resolution issues as suggested in the Symantec KB to no avail. The only thing I can think of, at this point, is that a trial license doesn't allow me to use the Archiving function, although that would seem silly on their part. Appreciate any assistance or information. Thanks.

  Read the article

• Automate creation of Windows startup script?

  - by Niten

  Is there a good way to automate installing local startup (rather than login) scripts in Windows XP and Windows 7, via the command line, WMI, COM, or otherwise (even Win32 if it comes to that)? I need to setup a local startup script on a large number of computers, and unfortunately, Active Directory is absolutely not an option. I would like to write a script or small program that I can run on each computer to perform the startup script installation in order to save myself a lot of error-prone point-and-click manual labor. I see that when one uses gpedit.msc to create a local startup script, information about the script gets stored in the registry here: HKLM\Software\Policies\Microsoft\Windows\System\Scripts\Startup However, if you create such a script and then delete its registry key, the script will remain listed in the local Group Policy editor; as is so often the case in Windows, apparently there is more going on there than meets the eye. This leads me to question whether it's safe to manually add subkeys for new startup scripts here (I wouldn't want my script to be overwritten by later changes made using the local Group Policy editor, for instance)... Another option that's occurred to me is to create an item in the Task Scheduler configured to run at system startup. However, my concerns there are twofold: Can this be automated any more easily? For instance, the at command doesn't appear to let you schedule a task for system startup, and WMI's Win32_ScheduledJob interface looks unreliable (it fails to show any of my currently scheduled tasks, for one thing). Would I be able to prevent users from logging in until the scheduled startup task is completed, as can be done with "normal" Windows startup scripts? Thanks in advance for any suggestions, I've been banging my head against this one for a bit...

  Read the article

• Supermicro X8SIL-F with Enermax Modu82+ 625W PSU booting issue

  - by Richard Whitman

  I am assembling a custom PC. The configuration is below: Motherboard: Supermicro X8SIL-F Processor: Intel Xeon 3430 Power Supply: Enermax Modu82+ 625W. Memory: Kingston KVR1333D3LQ8R9S/8GEC 8GBx1 installed in DimmA1 This power switch: Frozen CPU switch When I turn on the PSU, the motherboard tries to start itself before I even push the power switch. The following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and this time it rotates for about 3-4 seconds before stopping. If I pull out the Power switch, and turn on the PSU, again the MB turns on itself and the following happens: The CPU fan rotates like once or twice, and then stops. After 1-2 seconds, the CPU fan tries to rotate again and stops after about one or two rotations. Finally, after another 1-2 seconds, it again starts and the system boots properly I am sure there is nothing wrong with any of the components, because I have two sets of identical components (2 MBs, 2 CPUs, 2 PSUs, 2 switches and so on). And both of the systems show the same symptoms. Why is the MB booting up by itself? Why does it fail to boot when the Power Switch is installed? Is something wrong with the type of Power Switch I am using? PS: the power switch is installed correctly, I have double checked the MB manual to make sure its connecting the right pins.

  Read the article

• The SSL certificate doesn't established

  - by Andrey Eagle

  situation following: Windows Server 2008 R2 platform. Certificate installation in the IIS Manager occurs successfully with *.cer file but if I refresh the manager (F5), the certificate vanishes from the list. And, respectively in the Bindings window, at https addition, the certificate is absent in the menu. Thus if to open certificates via the MMS console, it can be seen in the Personal store. Whether there is any possibility to make so that the web server could "see" this certificate or how to make so that it didn't disappear from the list? Prompt how to solve this problem, thanks in advance! P.S. The certificate is acquired in tawte. In total that to me provided, these are account data where it is possible simply with save-pastit the certificate in 2 options: PKCS#7 and X.509. Here is the manual I used. P.S.2 If Complete Certificate Request with *.p7b I get an error: Cannot find the certificate request that is associated with this certificate file. Acertificate request must be comleted on the computer where the request was created.

  Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >