Search Results

Search found 10169 results on 407 pages for 'port'.

Page 91/407 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

  • Troubles doing transparent proxy for virtual machines

    - by Dan H
    Hi iptables gurus. First here is the basic topology: Internet | Gateway | Workstation---eth0---virbr0 | +-----+-----+ | | | vm1 vm2 vm3 I need to test a traffic analyzer running on my workstation, listening on some port (say 8990) on eth0. The rule [I think] I want is "any packets leaving virbr0 going anywhere to port 80 must instead go to port 8990 on eth0". My software running on port 8990 does its own check of the NAT packet mangling to push the packets through after it inspects them. I've been banging my head on this, with different variants of: iptables -t nat -A PREROUTING -i virbr0 -p tcp --dport 80 -j DNAT \ --to 10.0.0.10:8990 And I've tried the more generic method of using the mangle table with --set-mark and ip rule add fwmark, but I'm not getting it. I guess what's confusing me is that everything runs on the same box. Thanks for any guidance.

    Read the article

  • Enabling "USB Printing Support" in Windows 7

    - by Kevin Dente
    I'm trying to use an old parallel-port based printer with a USB-to-parallel port adapter on Windows 7. When I plug it into the USB port on the computer it's listed as an unrecognized device. I know that these cables typically use the "USB Printing Support" driver with makes USB ports show up as printer ports in the printer dialog. Is there a way to manually add USB Printing Support to Windows 7, since it isn't being added automatically?

    Read the article

  • Accessing localhost:8080 through local network

    - by Theron Luhn
    I'm developing a Python WSGI website. I'm running a Paste development server on my Mac (OS X 10.7) on port 8080. I want to test the website on some other devices and OSs I have connected to the local network (Windows 7 VM, iPad, iPhone, etc.), but am having trouble. I turned on Web Sharing, and am able to access that (port 80) without a problem on all my devices. Port 8080 still doesn't work. An excerpt from my Paste configuration: [server:main] use = egg:waitress#main host = 127.0.0.1 port = 8080 The OS X firewall (Settings - Security - Firewall) is off. I have no other firewall software installed. My network is through a Linksys WRT160N router. I haven't done much with the settings, so most of them are at their defaults. I've been Googling all morning, but can't find a solution.

    Read the article

  • Running Tomcat 7 and Apache 2 on the same server

    - by Thorn
    Part of my site needs to run over HTTPS and I'm creating a sub-domain for that part. I have apache httpd 2 AND Tomcat 7 running on the same server with the same IP, Apache is on port 80 of course, while Tomcat is running on port 8080. Right now I am doing domain forwarding for requests that need to run off tomcat. For example, mathteamhosting.com/mathApp can forward to mathteamhosting.com:8080/mathApp. I would like to have Tomcat handle the https requests for that subdomain. I don't think this forwarding technique can work in this case. How do I set that up so that Tomcat receives the requests on port 443 while apache handles port 80. To be more specific: http://proctinator.com == request goes to Apache web server https://private.proctinator.com == request goes to Apache web server

    Read the article

  • No sigal showing on LCD TV when Conects Leptop via VGA Cable

    - by Amit Prajapati
    I am trying to connect my laptop to Samsung LCD TV by VGA TO HDMI cable My Laptop find Samsung tv on display setting. But When I press fn+F7 key my TV display No Signal My laptop specifications are: "Lenovo R61 ThinkPad, Model: 8935AE7 Window7 Ultimate 32 bits 2GB RAM VGA Port available No HDMI Port My TV specification are: Samsung LCD 26 HDMI Port available VGA Port Available I want to know what is problem? When I connect Another Dell Laptop (Window7 32 bit) with HDMI to HDMI cable it work properly. Thanks in Advance!

    Read the article

  • Slow WLAN file transfer between server and tablet

    - by user266985
    My file server is running Ubuntu 12.04 and I'm sharing files from it over samba. It is connected via gigabit ethernet. My desktop, running Windows 8.1, is also connected via gigabit ethernet. I can transfer files between the two and completely saturate that gigabit pipe. However, I just got a Surface Pro 2, and I'm trying to stream HD movies from my server to the device over WiFi. For some reason, I can't break much past 1.5MB/s transferring files over the network. I've tried streaming through XBMC and a standard file copy; no difference. To add the confusion, if I connect to my guest network and then use my VPN server (installed on the router) to access the file server, I get around 3.2MB/s. I've been running diagnostics to determine the root and I think I've found it but I have no idea what is causing it or how to fix it. Router: Asus RT-N66U Surface Pro 2 Network Card: Marvell Avastar 350N (Driver 19/09/2013 v14.69.24044.150) InSSIDer: Link Score: 100 Co-Channels: 0 Overlapping: 0 5GHz Network Channel: 48+44 iperf File Server as Server; Surface Pro 2 as Client - TCP Performance: Acceptable ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 4] local 192.168.0.90 port 5001 connected with 192.168.0.56 port 57367 [ ID] Interval Transfer Bandwidth [ 4] 0.0- 1.0 sec 10.1 MBytes 84.7 Mbits/sec [ 4] 1.0- 2.0 sec 10.4 MBytes 87.6 Mbits/sec [ 4] 2.0- 3.0 sec 10.6 MBytes 88.8 Mbits/sec [ 4] 3.0- 4.0 sec 10.7 MBytes 89.5 Mbits/sec [ 4] 4.0- 5.0 sec 10.1 MBytes 84.4 Mbits/sec [ 4] 5.0- 6.0 sec 10.2 MBytes 85.8 Mbits/sec [ 4] 6.0- 7.0 sec 7.04 MBytes 59.1 Mbits/sec [ 4] 7.0- 8.0 sec 10.8 MBytes 90.2 Mbits/sec [ 4] 8.0- 9.0 sec 10.6 MBytes 89.1 Mbits/sec [ 4] 9.0-10.0 sec 8.62 MBytes 72.3 Mbits/sec [ 4] 0.0-10.0 sec 99.2 MBytes 83.1 Mbits/sec iperf Surface Pro 2 as Server, File Server as Client Performance: Poor ------------------------------------------------------------ Client connecting to 192.168.0.56, TCP port 5001 TCP window size: 22.9 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.0.90 port 40233 connected with 192.168.0.56 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0- 1.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 1.0- 2.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 2.0- 3.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 3.0- 4.0 sec 1.25 MBytes 10.5 Mbits/sec [ 3] 4.0- 5.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 5.0- 6.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 6.0- 7.0 sec 1.38 MBytes 11.5 Mbits/sec [ 3] 7.0- 8.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 8.0- 9.0 sec 1.50 MBytes 12.6 Mbits/sec [ 3] 9.0-10.0 sec 1.62 MBytes 13.6 Mbits/sec [ 3] 0.0-10.1 sec 15.0 MBytes 12.4 Mbits/sec For some reason, it gets capped and I haven't got a clue why. Any suggestions? Edit: My link speed is reported as 270Mbps by Windows. I'm less than two metres from the router with a clear line of sight.

    Read the article

  • Is A Managed Switch With VLAN Support Required

    - by Justin
    Hello, I am wondering if I need to buy a switch which is managed (VLAN support) for my configuration, or will a cheaper unmanaged switch work? I have servers with two NICS each. The first NIC is public and the second NIC is private. The router will plug into the switch port 1 let's say (public). Then server 1 public plugs into port 2 on the switch, and sever 1 private plugs into port 3 on the switch. The public interface is: 192.168.X.X / 255.255.0.0 and the private interface is 10.0.X.X / 255.255.0.0. So looks like: ** SWITCH ** Port Device Network 1 Router/Firewall 192.168.X.X 2 Server 1 Public 192.168.X.X 3 Server 1 Private 10.0.X.X 4 Server 2 Public 192.168.X.X 5 Server 2 Private 10.0.X.X 6 Server 3 Public 192.168.X.X 7 Server 3 Private 10.0.X.X Thanks.

    Read the article

  • ip6tables TPROXY not working

    - by CookieMunster
    I have a problem, I need to have to run a java program on a port < 1024. authbind and jsvc are no alternatives, it is simply decided not to use. But using ip6tables -t mangle -A PREROUTING -p udp --dport 546 -j TPROXY --on-port 8547 gives me ip6tables v1.4.7: unknown option `--on-port' What did I miss? uname -a Linux vieppetat12 2.6.32-71.el6.x86_64 #1 SMP Wed Sep 1 01:33:01 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux

    Read the article

  • LDAP replication breaking referrals

    - by MasterZ
    We have an issue that we believe is caused by ldap replication changing the port of the referal from 686 (secure) to 389 (unsecure). If we setup a new referral everything works, but then as soon as we change someone's password it changes on the master, and then the master replicates and the referral breaks. Any further attempts to modify someone's account give the error "PAM: Cannot connect to LDAP". We used snoop and monitored the firewall to see what was going on. The first password attempt (the one that works) goes over port 686 (as it is supposed to) but every subsequent attempt attempts to use port 389, and therefore fails. We only have 1 referral configured on the client, port 686

    Read the article

  • A Service specific error occured:1 on trying to start apache 2.0 server.(Windows 7)

    - by user2297366
    I installed apache on my computer(localhost) and it worked fine. Then I went to download some other stuff and later noticed that the apache server stopped. So I went to command prompt(as administrator) and typed net start apache2. It says The Apache2 Service is starting. But before it finishes, I get the error A Service Specific Error Occurred: 1. It says that you can type in something for more info, but that doesn't help at all. Things I have tried: 1: Quit Google Drive Sync 2: Quit any and all programs using port 80(port my server is on) 3. I even tried changing the port of the server and got same error message, so I don't think it has anything to do with something else being in the port. None of those things have worked. I am confused at why it worked earlier, but now it won't work. Any help is greatly appreciated.

    Read the article

  • Need to set up a proxy on Linksys E3200 to filter home internet

    - by Justin Amberson
    the fact that I have a Linksys E3200 may not be important. I can configure the router through the web interface, but I don't know the things I will be toggling are called. I already do simple port forwarding to access applications on my Mac remotely. So router admin is not something I technically need explained. I'm looking to running a proxy on my home computer, that filters all HTTP traffic that goes through my router. So if my daughter is on her iPad and accesses Safari, my Mac will be the judge of the validity of the request. I need something like NetNanny I guess, but local. Actually, anything that can just filter all port 80 traffic that runs locally, but maybe validates with a password? I truly truly hope this question falls within the bounds of Serverfault. I'm not a total internet newb but I'm at a loss for what to Google. If possible answer this question: Is there a webapp that can listen on port 80, and validate requests to port 80 with a password? If so, can I forward all traffic on port 80 to my Mac, to be re-routed to the user? Is this the same as a VPN? Thank you for your help. Justin

    Read the article

  • Why is there an extra HDD under /dev being added in my Linux Kernel?

    - by user1279156
    I have created a Linux kernel and for some reason an extra drive is always added at bootup. My hard drive is listed as /dev/sdb. /dev/sda is created too, and it is 8 MB in size. I can't find anything in the kernel config that is creating this, but if I use a different kernel it is not there. Kernel logs show it as an attached SCSI device, looks just like my hard drive but only 8 MB, and has no partition table. It also doesn't appear to be a physical device. I've tried the kernel on many different models of PCs and it is always there. Does anyone know how to remove it? /dev/disk/by-id gives me: scsi-1AMCC_U21413034D98EB000584 scsi-1AMCC_U21413034D98EB000584-part1 scsi-353333330000007d0 scsi-SATA_ST3250312AS_5VY7SH42 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part1 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part2 hdparm -i /dev/sda gives me an "invalid argument". dd if=/dev/sda of=sda.img the resulting file does not have any content sdparm results: /dev/sda: Linux scsi_debug 0004 Device identification VPD page: Addressed logical unit: designator type: T10 vendor identification, code set: ASCII vendor id: Linux vendor specific: scsi_debug 2000 designator type: NAA, code set: Binary 0x53333330000007d0 Target port: designator type: Relative target port, code set: Binary transport: Serial Attached SCSI (SAS) Relative target port: 0x1 designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007ce designator type: Target port group, code set: Binary transport: Serial Attached SCSI (SAS) Target port group: 0x100 Target device that contains addressed lu: designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007cd designator type: SCSI name string, code set: UTF-8 transport: Serial Attached SCSI (SAS) SCSI name string: naa.52222220000007CD

    Read the article

  • IPTables Reroute SSH based on Connection string?

    - by senrabdet
    We are using a cloud server (Debian Squeeze) where public ports on a public IP route traffic to internal servers. We are looking for a way to use IPTables and ssh where based on some part of the ssh connection string (or something along these lines) iptables will reroute the ssh connection to the "right" internal server. This would allow us to use one common public port, and then re-route ssh connections to individual servers. So, for example we hope to do something like the following: user issues ssh connection (public key encryption) such as ssh -X -v -p xxx [email protected] but maybe adds something into the string for iptables to use iptables uses some part of that string or some means to re-route the connection to an internal server using something like iptables -t nat -A PREROUTING ! -s xxx.xxx.xxx.0/24 -m tcp -p tcp --dport $EXTPORT -j DNAT --to-destination $HOST:$INTPORT ....where $HOST is the internal ip of a server, $EXTPORT is the common public facing port and $INTPORT is the internal server port. It appears that the "string" aspect of iptables does not do what we want. We can currently route based on the IP table syntax we're using, but rely on having a separate public port for each server and are hoping to use one common public port and then re-route to specific internal servers based on some part of the ssh connection string or some other means. Any suggestions? Thanks!

    Read the article

  • FTP timeout but SSH is working?

    - by nmarti
    I have a problem in my server, when I try to connect via FTP to a domain, the connexion is VERY slow, and I get timeouts just listing files in a directory. When I try to connect to the domain folder using the root user account via SSH, it works fine, and I can download the files without problem. What can be wrong? I tried to reboot the server, also the office router, and nothing... It is a fedora core 7 server with proftpd. Can it be a filesystem problem? Thanks. CONNECTION LOG: Cmd: MLST about.php 250: Start of list for about.php modify=20120910092528;perm=adfrw;size=2197;type=file;UNIX.group=505;UNIX.mode=0644;UNIX.owner=10089; about.php End of list Cmd: PASV 227: Entering Passive Mode (***hidden***). Data connection timed out. Falling back to PORT instead of PASV mode. Connection falling back to port (PORT) mode. Cmd: PORT ***hidden*** 200: PORT command successful Cmd: RETR about.php Could not accept a data connection: Operation timed out.

    Read the article

  • CentOS and OpenSSH [on hold]

    - by Stephen
    I've recently installed CentOS 6 on an old Dell PC. I'm trying to setup OpenSSH at the moment, I been following some tutorials (http://www.youtube.com/watch?v=QKafb0koJEg) on You Tube, while they have been very helpful I'm at the point where I need to ask some questions. My goal here is to be able to access the server from my work computer and from my personal laptop (which will be on the same home network as the server). I've installed OpenSSH with no issues. So the first thing I was advised to do was port forwarding. So in the sshd_config file, I've changed Port 22 to Port xxxx (where xxxx is a obviously a four digit value). I then restart the sshd service. I've also configured my router for forward port 22 onto xxxx. Is there anything else I need to do? I've generated the keys on my laptop, and I'm trying to copy them to the server as follows: scp id_rsa.pub xxxxxxxx@localhost:.ssh/authorized_keys but this command fails with the following error message: ssh: connect to host localhost port 22: Connection refused lost connection Any help appreciated. Regards...

    Read the article

  • Tomcat hangs in shutdown

    - by Morven
    I have a Tomcat server that won't shut down. It is listening on the correct port (8005, for this one) to receive the SHUTDOWN command. I can issue that command, either with the bin/shutdown.sh script or by telnetting to that port and typing SHUTDOWN. At this point, the shutdown port closes; I can no longer connect to it. The AJP13 port stays open, though; nothing is logged in catalina.out, and things don't shut down. Anyone seen this before? This is on Solaris 10 on Sparc, if it matters (it probably doesn't) and Tomcat version 6.0.20.

    Read the article

  • MSSQL 2012 Error 26 and remote connection

    - by Rayfloyd
    I'm trying to set up MSSQL 2012 for a school project and I need to be able to connect to it remotely as my teammates will also be working on it. I did a clean install of SQL Server 2012 Express. Knowing I can't connect remotely straight off, I tweaked the settings that needed tweaking according to the internet. What I did 1.Made sure remote connections were allowed 2.Enabled TCP/IP 3.Removed 0s from Dynamic ports and set 1433 in TCP Port 4.Enabled Named Pipes 5.Created Outbound and Inbound traffic rules in the firewall for TCP port 1433 and UDP port 1434 6.Port forwarded 1433 to my "server" and 1434 too 7.made sure I was pingable 8.SQL Server authentication is enabled 9.I have restarted my computer so that changes to the config are saved So whenever I try to connect using management studio on another computer than the server using myusername.dyndns.org\SQLEXPRESS I get error 26 I have been searching for different solutions for 3 hours with no luck.

    Read the article

  • Performance problem with an Intel Wireless 5100

    - by Piet
    I just installed 12.04 on a HP Elitebook 2530p. The performance with wireless connection to an Eminem 4551 is very bad. Wired connection just works great. If I connect to my router (Eminent 4551) wired I have a good performance accessing internet pages with Firefox. When I try to access the same internet pages wireless I get a real bad performance. piet@piet-HP-EliteBook-2530p:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07) 00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) 00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 02:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection 44:06.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 44:06.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) piet@piet-HP-EliteBook-2530p:~$

    Read the article

  • How to use Nginx to export the mongoDB connection?

    - by Totty
    I have on my server 2 things: the node.js server and a mongodb database; The node.js server is reachable from myip/server; and now I would like to export the mongodb database to myip/database for example. Now when I use my mongodb viewer (MongoVUE) with "http://myip/database:9000" (the port 9000 is set in nginx and it's also the port that I start mongod). If I go to "http://myip/database:9000" or "http://myip/database" in a browser it look like: "You are trying to access MongoDB on the native driver port. For http diagnostic access, add 1000 to the port number". But in MongoVUE it says: Unable to connect to server 192.168.1.16/database:9000: No such host is known. Type: MongoDB.Driver.MongoConnectionException Stack: at MongoDB.Driver.Internal.DirectConnector.Connect(TimeSpan timeout) at MongoDB.Driver.MongoServer.Connect(TimeSpan timeout, ConnectWaitFor waitFor) at MongoDB.Driver.MongoServer.Connect(TimeSpan timeout) at MongoDB.Driver.MongoServer.Connect() at MangoUI.MMongo.FQlxNlJKqO74gYmXgZR4(Object ) at MangoUI.MMongo.Open(Boolean useSamus) at MangoUI.MMongo.Open() at MangoUI.ComNavTree.wJQdUqApCpjoC39P59n(Object ) at MangoUI.ComNavTree.ExpandMe(MTreeNode expand) at MangoUI.ComNavTree.tree_BeforeExpand(Object sender, TreeViewCancelEventArgs e) No such host is known Type: System.Net.Sockets.SocketException Stack: at System.Net.Dns.GetAddrInfo(String name) at System.Net.Dns.InternalGetHostByName(String hostName, Boolean includeIPv6) at System.Net.Dns.GetHostAddresses(String hostNameOrAddress) at MongoDB.Driver.MongoServerAddress.ToIPEndPoint(AddressFamily addressFamily) at MongoDB.Driver.MongoServerInstance.Connect(Boolean slaveOk) at MongoDB.Driver.Internal.DirectConnector.Connect(TimeSpan timeout)

    Read the article

  • EPM 11.1.2.2 Architecture: Essbase

    - by Marc Schumacher
    Since a lot of components exist to access or administer Essbase, there are also a couple of client tools available. End users typically use the Excel Add-In or SmartView nowadays. While the Excel Add-In talks to the Essbase server directly using various ports, SmartView connects to Essbase through Provider Services using HTTP protocol. The ability to communicate using a single port is one of the major advantages from SmartView over Excel Add-In. If you consider using Excel Add-In going forward, please make sure you are aware of the Statement of Direction for this component. The Administration Services Console, Integration Services Console and Essbase Studio are clients, which are mainly used by Essbase administrators or application designers. While Integration Services and Essbase Studio are used to setup Essbase applications by loading metadata or simply for data loads, Administration Services are utilized for all kind of Essbase administration. All clients are using only one or two ports to talk to their server counterparts, which makes them work through firewalls easily. Although clients for Provider Services (SmartView) and Administration Services (Administration Services Console) are only using a single port to communicate to their backend services, the backend services itself need the Essbase configured port range to talk to the Essbase server. Any communication to repository databases is done using JDBC connections. Essbase Studio and Integration Services are using different technologies to talk to the Essbase server, Integration Services uses CAPI, Essbase Studio uses JAPI. However, both are using the configured port range on the Essbase server to talk to Essbase. Connections to data sources are either based on ODBC (Integration Service, Essbase) or JDBC (Essbase Studio). As for all other components discussed previously, when setting up firewall rules, be aware of the fact that all services may need to talk to the external authentication sources, this is not only needed for Shared Services.

    Read the article

  • Clustering in GlassFish with DCOM on Windows 7

    - by ByronNevins
    I've discovered that Windows 7 makes it very difficult to use DCOM and, mainly, the GlassFish clustering commands that rely on DCOM.  I spent a few days trying to solve the problems.  I don't yet have a cookbook for making DCOM work on Windows 7.  But here are a few tips and advice I've found. run asadmin setup-local-dcom -- It now comes automatically with the open source GlassFish 4.  It will write some critical registry entries for you.  run asadmin validate-dcom to test dcom 3.   When I ran validate-dcom on my Windows 7 network I saw the problem below: Successfully resolved host name to: gloin/10.28.51.10 Successfully connected to DCOM Port at port 135 on host gloin. Successfully connected to NetBIOS Session Service at port 139 on host gloin.Successfully connected to Windows Shares at port 445 on host gloin.Can not access the remote file system.  Is UAC on? : Access is denied. I discovered the actual problem is that Windows 7 no longer has the "C$" Administrative file share available by default. If "C$" isn't available then nothing will work. Here is how to expose the "C$" share: Registry Change -- this change allows “C$” to be accessed.  As soon as I set it -- the file copying started working!  [1] regkey: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System create this key, 32 bit word, with value == 1 LocalAccountTokenFilterPolicy 4.  Turn on the Remote Registry Service -- This is critical and it's easy to do. Windows 7 has it turned off by default. MyComputer-right click, manage, services, then turn on Remote Registry Service and set it to start automatically in the fture. 5. Turn off UAC: %systemroot%\system32\UserAccountControlSettings.exe 6. This is where I discovered that McAfee virus scanner blocks all the NetBios shares!  It has to be disabled.  

    Read the article

  • Why doesn't lsof show localhost TCP connections in 14.04?

    - by sfussenegger
    I have two servers running 12.04.4 and 14.04.1 respectively. Both have nginx (port 80) and a Java process (port 8080). As expected, the lsof output for the Java process on the 12.04 machine shows a couple of established connections for port 8080 (e.g. TCP 127.0.0.1:8080->127.0.0.1:58067 (ESTABLISHED)) The 14.04 machine however does not. It only shows the listening port (TCP *:8080 (LISTEN)). I'm sure there are active connections though (confirmed by access logs, Java process status output, etc). What has changed from 12.04 to result in this behavior? Can this change be the cause for the "Too many open files" errors I'm getting since moving from 12.04 to 14.04? 12.04: $ dpkg -l lsof linux-image-virtual openjdk-7-jre nginx ||/ Name Version +++-===========================================-=========================================== ii linux-image-virtual 3.2.0.59.70 ii lsof 4.81.dfsg.1-1build1 ii nginx 1.6.1-1~precise ii openjdk-7-jre 7u65-2.5.1-4ubuntu1~0.12.04.1 14.04: $ dpkg -l lsof linux-image-virtual openjdk-7-jre nginx-full ||/ Name Version Architecture Description +++-=====================================-=======================-======================= ii linux-image-virtual 3.13.0.32.38 amd64 ii lsof 4.86+dfsg-1ubuntu2 amd64 ii nginx-full 1.4.6-1ubuntu3 amd64 ii openjdk-7-jre:amd64 7u65-2.5.1-4ubuntu1~0.1 amd64

    Read the article

  • Netcat I/O enhancements

    - by user13277689
    When Netcat integrated into OpenSolaris it was already clear that there will be couple of enhancements needed. The biggest set of the changes made after Solaris 11 Express was released brings various I/O enhancements to netcat shipped with Solaris 11. Also, since Solaris 11, the netcat package is installed by default in all distribution forms (live CD, text install, ...). Now, let's take a look at the new functionality: /usr/bin/netcat alternative program name (symlink) -b bufsize I/O buffer size -E use exclusive bind for the listening socket -e program program to execute -F no network close upon EOF on stdin -i timeout extension of timeout specification -L timeout linger on close timeout -l -p port addr previously not allowed usage -m byte_count Quit after receiving byte_count bytes -N file pattern for UDP scanning -I bufsize size of input socket buffer -O bufsize size of output socket buffer -R redir_spec port redirection addr/port[/{tcp,udp}] syntax of redir_spec -Z bypass zone boundaries -q timeout timeout after EOF on stdin Obviously, the Swiss army knife of networking tools just got a bit thicker. While by themselves the options are pretty self explanatory, their combination together with other options, context of use or boundary values of option arguments make it possible to construct small but powerful tools. For example: the port redirector allows to convert TCP stream to UDP datagrams. the buffer size specification makes it possible to send one byte TCP segments or to produce IP fragments easily. the socket linger option can be used to produce TCP RST segments by setting the timeout to 0 execute option makes it possible to simulate TCP/UDP servers or clients with shell/python/Perl/whatever script etc. If you find some other helpful ways use please share via comments. Manual page nc(1) contains more details, along with examples on how to use some of these new options.

    Read the article

  • Direct IO enhancements in OVM Server for SPARC 2.2(a.k.a LDoms2.2)

    - by user12611315
    The Direct I/O feature has been available for LDoms customers since LDoms2.0. Apart from the latest SR-IOV feature in LDoms2.2, it is worth noting a few enhancements to the Direct I/O feature. These are: Support for Metis-Q and Metis-E cards. These cards are highly requested for support and are worth mentioning because they are the only combo cards containing both FibreChannel and Ethernet in the same card. With this support, a customer can have both SAN storage and network access with just one card and one PCIe slot assigned to a logical domain. This reduces cost and helps when there are less number of slots in a given platform. The following are the part numbers for these cards. I have tried to put the platforms on which each card is supported, but this information can get quickly outdated. The accurate information can be found at the Support Document.  Card Name  Part Number  Platforms Metis-Q: StorageTek Dual 8Gb Fibre Channel Dual GbE ExpressModule HBA, QLogic SG-XPCIEFCGBE-Q8-N  SPARC T3-4, T4-4 Metis-E: StorageTek Dual 8Gb Fibre Chanel Dual GbE ExpressModule HBA, Emulex SG-XPCIEFCGBE-E8-N SPARC T3-4, T4-4  Additional cards added to the portfolio of supported cards. This is mainly Powerville based Ethernet cards, the part numbers for these cards as below:  Part Number  Description  7100477 Sun Quad Port GbE PCI Express 2.0 Low Profile Adapter, UTP  7100481 Sun Dual Port GbE PCI Express 2.0 Low Profile Adapter, MMF  7100483 Sun Quad Port GbE PCI Express 2.0 ExpressModule, UTP  7110486 Sun Quad Port GbE PCI Express 2.0 ExpressModule, MMF    Note:  Direct IO feature has a hard dependency on the Root domain(PCIe bus owner, here Primary domain). That is, rebooting the Root domain for any reason may impact the logical domains having PCIe slots assigned with Direct IO feature. So rebooting a root domain need to be carefully managed. Also apply the failure-policy settings as described in the admin guide and release notes to deal with unexpected cases.

    Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >