Search Results

Search found 10527 results on 422 pages for 'ccnet config'.

Page 92/422 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

  • How to connect 2 routers (Asmax and D-link)

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • While loop read multiple lines from a grep

    - by Basil
    I'm writing a script in AIX 5.3 that will loop through the output of a df and check each volume against another config file. If the volume appears in the config file, it will set a flag which is needed later in the script. If my config file only has a single column and I use a for loop, this works perfectly. My problem, however, is that if I use a while read loop to populate more than one variable per line, any variables I set between the while and the done are discarded. For example, assuming the contents of /netapp/conf/ExcludeFile.conf are a bunch of lines containing two fields each: volName="myVolume" utilization=70 thresholdFlag=0 grep volName /netapp/conf/ExcludeFile.conf | while read vol threshold; do if [ $utilization -ge $threshold ] ; then thresholdFlag=1 fi done echo "$thresholdFlag" In this example, thresholdFlag will always be 0, even if the volume appears in the file and its utilization is greater than the threshold. I could have added an echo "setting thresholdFlag to 1" in there, see the echo, and it'll still echo a 0 at the end. Is there a clean way to do this? I think my while loop is being done in a subshell, and changes I make to variables in there are actually being made to local variables that are discarded after the done.

    Read the article

  • Trying to install datastax opscenter - Failed to load application: cannot import name _parse

    - by gansbrest
    I'm not familiar with python, maybe someone could explain what's going on here? ec2-user@prod-opscenter-01:~ % java -version java version "1.7.0_45" Java(TM) SE Runtime Environment (build 1.7.0_45-b18) Java HotSpot(TM) 64-Bit Server VM (build 24.45-b08, mixed mode) ec2-user@prod-opscenter-01:~ % python -V Python 2.6.8 ec2-user@prod-opscenter-01:~ % openssl version OpenSSL 1.0.1e-fips 11 Feb 2013 And now the error ec2-user@prod-opscenter-01:~ % sudo /etc/init.d/opscenterd start Starting Cassandra cluster manager opscenterd Starting opscenterdUnhandled Error Traceback (most recent call last): File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 652, in run runApp(config) File "/usr/lib64/python2.6/site-packages/twisted/scripts/twistd.py", line 23, in runApp _SomeApplicationRunner(config).run() File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 386, in run self.application = self.createOrGetApplication() File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 451, in createOrGetApplication application = getApplication(self.config, passphrase) --- <exception caught here> --- File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 462, in getApplication application = service.loadApplication(filename, style, passphrase) File "/usr/lib64/python2.6/site-packages/twisted/application/service.py", line 405, in loadApplication application = sob.loadValueFromFile(filename, 'application', passphrase) File "/usr/lib64/python2.6/site-packages/twisted/persisted/sob.py", line 210, in loadValueFromFile exec fileObj in d, d File "bin/start_opscenter.py", line 1, in <module> from opscenterd import opscenterd_tap File "/usr/lib/python2.6/site-packages/opscenterd/opscenterd_tap.py", line 37, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/OpsCenterdService.py", line 13, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/ClusterServices.py", line 22, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/WebServer.py", line 40, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/Agents.py", line 18, in <module> exceptions.ImportError: cannot import name _parse Failed to load application: cannot import name _parse Maybe there are open source alternatives to monitoring cassandra I should look at? Thanks a lot

    Read the article

  • OpenSSL error while running punjab

    - by Hunt
    i ran punjab - BOSH connection manager - using twistd -y punjab.tac command in my centos but i am getting following error Unhandled Error Traceback (most recent call last): File "/usr/local/lib/python2.7/site-packages/twisted/application/app.py", line 652, in run runApp(config) File "/usr/local/lib/python2.7/site-packages/twisted/scripts/twistd.py", line 23, in runApp _SomeApplicationRunner(config).run() File "/usr/local/lib/python2.7/site-packages/twisted/application/app.py", line 386, in run self.application = self.createOrGetApplication() File "/usr/local/lib/python2.7/site-packages/twisted/application/app.py", line 451, in createOrGetApplication application = getApplication(self.config, passphrase) --- <exception caught here> --- File "/usr/local/lib/python2.7/site-packages/twisted/application/app.py", line 462, in getApplication application = service.loadApplication(filename, style, passphrase) File "/usr/local/lib/python2.7/site-packages/twisted/application/service.py", line 405, in loadApplication application = sob.loadValueFromFile(filename, 'application', passphrase) File "/usr/local/lib/python2.7/site-packages/twisted/persisted/sob.py", line 210, in loadValueFromFile exec fileObj in d, d File "punjab.tac", line 39, in <module> '/etc/pki/tls/cert.pem', File "/usr/local/lib/python2.7/site-packages/twisted/internet/ssl.py", line 68, in __init__ self.cacheContext() File "/usr/local/lib/python2.7/site-packages/twisted/internet/ssl.py", line 78, in cacheContext ctx.use_privatekey_file(self.privateKeyFileName) OpenSSL.SSL.Error: [('x509 certificate routines', 'X509_check_private_key', 'key values mismatch')] Failed to load application: [('x509 certificate routines', 'X509_check_private_key', 'key values mismatch')] my configuration file of punjab is sslContext = ssl.DefaultOpenSSLContextFactory( '/etc/pki/tls/private/ca.key', '/etc/pki/tls/cert.pem', ) How can i resolve above error

    Read the article

  • Moving a site from IIs6 to IIS7.5

    - by Sukotto
    I need to move a site off of IIS6 (Win Server 2003) and onto IIS7.5 (Win Server 2008) as soon as possible. Preferably tomorrow. The site itself is a delightful mix of classic asp (vbscript) and one-off asp.net (C#) applications (each asp.net app is in its own virtual dir and has a self-contained web.config). In case it's relevant, this is a sort of research site made up of 40 or 50 unconnected microsites. Each microsite is typically a simple form allowing a user to submit a form, which then runs a Stored Proc on a sqlserver db and displays a chart and/or table of the results. There is very little security to worry about. The database connection info is in a central file (in the case of the classic asp) or app's individual web.config (lots of duplication there) To add a little spice to the exercise... I have no idea how to admin IIS The company no longer employs the sysadmin or the guys who set this thing up. (They're not going to employ me much longer either but my sense of professional pride does not permit me to just walk away from this task). The servers are on mutually firewalled networks and I have to perform a convoluted, multi-step process to copy anything from one to the other. Would someone please point me to a crash-course tutorial for accomplishing the above? I have: a complete copy of the site's filesystem on the new box installed the 3rd party charting tool on the new system a config.xml file from the "all tasks - save configuration to a file" right click menu. There doesn't seem to be a way to import it on the new system however. The newer IIS manager has a completely different UI and I'm totally lost. Please help.

    Read the article

  • Play framework 2.2 using Upstart 1.5 (Ubuntu 12.04)

    - by Leon Radley
    I'm trying to get Play 2.2 working with upstart. I've been running Play 2.x with upstart since it's release and it's never been a problem. But since the release of 2.2 and the change to http://www.scala-sbt.org/sbt-native-packager/ play doesn't want to start any more. Here's the config I'm using description "PlayFramework 2.2" version "2.2" env APP=myapp env USER=myuser env GROUP=www-data env HOME=/home/myuser/app env PORT=9000 env ADDRESS=127.0.0.1 env CONFIG=production.conf env JAVAOPTS="-J-Xms128M -J-Xmx512m -J-server" start on runlevel [2345] stop on runlevel [06] respawn respawn limit 10 5 expect daemon # If you want the upstart script to build play with sbt pre-start script chdir $HOME sbt clean compile stage -mem $SBTMEM end script exec start-stop-daemon --pidfile ${HOME}/RUNNING_PID --chuid $USER:$GROUP --exec ${HOME}/bin/${APP} --background --start -- -Dconfig.resource=$CONFIG -Dhttp.address=$ADDRESS -Dhttp.port=$PORT $JAVAOPTS I've changed the JAVAOPTS to include the -J- and I've also changed the path to use the new startscript located in the /bin/ dir. I've read that upstart 1.4 has setuid and setguid. I've tried removing the start-stop-daemon but I haven't got that working either. Any suggestions would be appreciated.

    Read the article

  • Cisco ASA site-to-site vpn not initiating phase 1 (not sending udp 500 packets)

    - by Sean Steadman
    I am hoping someone here can help me with my problem. I am trying to setup an IPSEC site-to-site VPN between two cisco ASA 5520's in GNS3 (both using 8.4.2). I have been unsuccesful in getting the tunnel up and it appears neither ASA is sending packets out,in regards to phase 1 and phase 2 (tested by using wireshark and seeing NO udp 500 packets). Doing show ipsec sa and such shows nothing. CALIFORNIA(config)# show ipsec sa There are no ipsec sas FLA-ASA# show ipsec sa There are no ipsec sas I will attach both configurations in two different pastebin files as to keep this post a bit cleaner. Essentially California side has 172.20.1.0/24 and Florida side has 10.10.10.0/24. California ASA config: http://pastebin.com/v0pngYzF Florida ASA config: http://pastebin.com/E2geybta Please let me know if there is any other vital information that could help. I have gotten IPSEC tunnels to work using openSwan (linux) and cisco routers but cannot for the life of me get ASA IPSEC tunnels to work. The ASDM is out of the question I only use cli. Thanks for any useful help!

    Read the article

  • Apache2 default vhost in alphabetical order or override with _default_ vhost?

    - by benbradley
    I've got multiple named vhosts on an Apache web server (CentOS 5, Apache 2.2.3). Each vhost has their own config file in /etc/httpd/vhosts.d and these vhost config files are included from the main httpd conf with... Include vhosts.d/*.conf Here's an example of one of the vhost confs... NameVirtualHost *:80 <VirtualHost *:80> ServerName www.domain.biz ServerAlias domain.biz www.domain.biz DocumentRoot /var/www/www.domain.biz <Directory /var/www/www.domain.biz> Options +FollowSymLinks Order Allow,Deny Allow from all </Directory> CustomLog /var/log/httpd/www.domain.biz_access.log combined ErrorLog /var/log/httpd/www.domain.biz_error.log </VirtualHost> Now I when anyone tries to access the server directly by using the public IP address, they get the first vhost specified in the aggregated config (so in my case it's alphabetical order from the vhosts.d directory). Anyone accessing the server directly by IP address, I'd like them to just get an 403 or a 404. I've discovered several ways to set a default/catch-all vhost and some conflicting opinions. I could create a new vhost conf in vhosts.d called 000aaadefault.conf or something but that feels a bit nasty. I could have a <VirtualHost> block in my main httpd.conf before the vhosts.d directory is included. I could just specify a DocumentRoot in my main httpd.conf What about specifying a default vhost in httpd.conf with _default_ http://httpd.apache.org/docs/2.2/vhosts/examples.html#default Would having a <VirtualHost _default_:*> block in my httpd.conf before I Include vhosts.d/*.conf be the best way for a catch-all?

    Read the article

  • SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

    - by eulerfx
    I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

    Read the article

  • default domain and first domain in apache2 causing trouble

    - by acidzombie24
    I have 3 sites and a default/test site using mono's test page. I created aFirst, c, d, e, zLast. zLast has rewrite rules that should be evaluated last. Since the first VirtualHost seen is the default i set it to this --aFirst-- <VirtualHost *:80> ServerName www.domain.tld ServerAdmin webmaster@localhost DocumentRoot /var/www/test DirectoryIndex index.html index.aspx index.php MonoDocumentRootDir "/var/www/test" MonoServerPath rootsite "/usr/local/bin/mod-mono-server2" MonoApplications rootsite "/:/var/www/test" <Directory /var/www/test> MonoSetServerAlias rootsite SetHandler mono AddHandler mod_mono .aspx .ascx .asax .ashx .config .cs .asmx </Directory> </VirtualHost> The problem is my default page (the ip address of my server) and the first website (csite.ddomain.net) have problems (even though csite is defined in c and is not the first virtual host). The ip address of my server and csite.ddomain.net ALWAYS load the same site. Either monos test page or the csite. It flips every time i restart apache. Why isnt the server ip address always loading the default page (mono test page) and why isnt csite.ddomain.net always loading the site i want!?! Heres the config for --csite-- <VirtualHost *:80> ServerName csite.testdomain.net ServerAdmin webmaster@localhost ServerAlias s.csite.testdomain.net DocumentRoot /var/www/prjname DirectoryIndex index.html index.aspx MonoDocumentRootDir "/var/www/prjname" MonoServerPath rootsite "/usr/local/bin/mod-mono-server2" MonoApplications rootsite "/:/var/www/prjname" <Directory /var/www/prjname> MonoSetServerAlias rootsite SetHandler mono AddHandler mod_mono .aspx .ascx .asax .ashx .config .cs .asmx </Directory> </VirtualHost> aFirst, c, d, e, zLast are all enabled.

    Read the article

  • Update Grub on Squeeze - Kernel downgrade due VMware Server

    - by vodoo_boot
    I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

    Read the article

  • Securing NTP: which method to use?

    - by Harry
    Can someone good at NTP configuration please share which method is the best/easiest to implement a secure, tamper-proof version of NTP? Here are some difficulties... I don't have the luxury of having my own stratum 0 time source, so must rely on external time servers. Should I read up on the AutoKey method or should I try to go the MD5 route? Based on what I know about symmetric cryptography, it seems that the MD5 method relies on a pre-agreed set of keys (symmetric cryptography) between the client and the server, and, so, is prone to man-in-the-middle attack. AutoKey, on the other hand, does not appear to work behind a NAT or a masquerading host. Is this still true, by the way? (This reference link is dated 2004, so I'm not sure what is the state of art today.) 4.1 Are public AutoKey-talking time servers available? I browsed through the NTP book by David Mills. The book looks excellent in a way (coming from the NTP creator after all), but the information therein is also overwhelming. I just need to first configure a secure version of NTP and then may be later worry about its architectural and engineering underpinnings. Can someone please wade me through these drowning NTP waters? Don't necessarily need a working config from you, just info on which NTP mode/config to try and may be also a public time server that supports that mode/config. Many thanks, /HS

    Read the article

  • How can I have Vhosts with Lighttpd on Windows and keeping PHP through mod_cgi ?

    - by Pixelastic
    Hello, I installed Lighty on Windows 7 and managed to get it correctly serve both static and PHP files (through mod_cgi). At first I got the "No input file selected" message displayed when requesting a .php file. So, I updated the doc_root value in my php.ini to match the server.document-root defined in my Lighty config, and PHP stops complaining. Then I defined a VHost to point all foo.com requests to a specific dir. It worked well for all static files but when requesting a .php file, the mod_cgi was still picking files from the doc_root defined in php.ini, not in the directory I defined for server.document-root in my Vhost. I know its what's supposed to happen, PHP follows the config defined in php.ini. And I have to set this value in my php.ini otherwise no php is processed at all. What I don't understand is how I'm supposed to have virtual hosts with mod_cgi enabled here ? I tried adding [HOST=foo.com] section in the php.ini without any luck. I tried mod_fastcgi but could'n get it to work at all, I also tried mod_simple_host but could get it handle php. I managed to get it working by copying my PHP install to another dir (and changing the doc_root value) and adding a cgi.assign pointing to that install in my vhost. But this is a really hackish way, it means having one PHP install for each virtualhost. Note that I'm working on a development machine running Windows, this is not a production server, I just wanted to emulate the final Server config locally to test some changes. I googled a lot this problem but all I can find are people installing Lighty on windows with mod_cgi, or installing Lighty on Windows with virtual hosts, but I never found anyone who managed to get both.

    Read the article

  • OpenLDAP 2.4.23 - Debian 6.0 - Import schema - Insufficient access (50)

    - by Yosifov
    Good day to everybody. I'm trying to add a new schema inside OpenLDAP. But getting an error: ldap_add: Insufficient access (50) root@ldap:/# ldapadd -c -x -D cn=admin,dc=domain,dc=com -W -f /tmp/test.d/cn\=config/cn\=schema/cn\=\{5\}microsoft.ldif root@ldap:/# cat /tmp/test.d/cn\=config/cn\=schema/cn\=\{5\}microsoft.ldif dn: cn=microsoft,cn=schema,cn=config objectClass: olcSchemaConfig cn: microsoft olcAttributeTypes: {0}( 1.2.840.113556.1.4.302 NAME 'sAMAccountType' DESC 'Fss ssully qualified name of distinguished Java class or interface' SYNTAX 1.3.6. 1.4.1.1466.115.121.1.27 SINGLE-VALUE ) olcAttributeTypes: {1}( 1.2.840.113556.1.4.146 NAME 'objectSid' DESC 'Fssssull y qualified name of distinguished Java class or interfaced' SYNTAX 1.3.6.1.4. 1.1466.115.121.1.40 SINGLE-VALUE ) olcAttributeTypes: {2}( 1.2.840.113556.1.4.221 NAME 'sAMAccountName' DESC 'Fds sssully qualified name of distinguished Java class or interfaced' SYNTAX 1.3. 6.1.4.1.1466.115.121.1.15 SINGLE-VALUE ) olcAttributeTypes: {3}( 1.2.840.113556.1.4.1412 NAME 'primaryGroupToken' SYNTA X 1.3.6.1.4.1.1466.115.121.1.27 SINGLE-VALUE ) olcAttributeTypes: {4}( 1.2.840.113556.1.2.102 NAME 'memberOf' SYNTAX 1.3.6.1. 4.1.1466.115.121.1.12 SINGLE-VALUE ) olcAttributeTypes: {5}( 1.2.840.113556.1.4.98 NAME 'primaryGroupID' SYNTAX 1.3 .6.1.4.1.1466.115.121.1.27 SINGLE-VALUE ) olcObjectClasses: {0}( 1.2.840.113556.1.5.6 NAME 'securityPrincipal' DESC 'Cso ntainer for a Java object' SUP top AUXILIARY MUST ( objectSid $ sAMAccountNam e ) MAY ( primaryGroupToken $ memberOf $ primaryGroupID ) ) I also tried to add the schema by phpldapadmin, but gain the same error. I'm using the admin user which is specified by default from the begging of the slpad installation. How may I add permissions to this user ? Best wishes

    Read the article

  • Configuring iptables rules for HAProxy and others

    - by MLister
    I have the following relevant settings for HAProxy: defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 500 contimeout 5s clitimeout 15s srvtimeout 15s frontend public bind *:80 option http-server-close option http-pretend-keepalive option forwardfor # ACLs ... I have three backends (including a Nginx server) configured in HAProxy, all listening on different ports of 127.0.0.1. And my iptables config is this: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT My questions are: Would the above iptables config work with the settings/options in my HAProxy config? I am also runnning a postgres and a redis server on the same machine, what settings do I need to adjust for these two to enable them work with iptables?

    Read the article

  • oracle access on vmware fusion

    - by gaudi_br
    Hello, I'm running snow leopard and I'm doing some development that requires some network knowledge. I've installed vmware fusion 3.0 and I've set up a virtual machine with windows 2003 server. I need to mimic the exact configuration of another server in the network, so I really need to run the versions I'll be mentioning here. Besides, I set up two network configurations on the VM: one NAT config (so that I can have internet access) and one host-only config (because I need to use another server's mac adress and my local area network might have a problem with it) From the installation of windows 2003, I then installed oracle 10.2.0.1. During the installation I received a warning about the primary ip-address of the system being dhcp assigned, but I ignored it (maybe it was a mistake)... Now, from experience, unless the DHCP assigned address changes, I should be able to access the guest system's database from the host system, so I went to safari and tried to access the oracle em. As it turns out, because my computer is on a company network, the company's DNS doesn't know about the virtual machine, unless of course I switch to a bridged network config. However, I don't want to do that because I don't to mix up the domains. So I guess the question is, how can I define my own dns or router, or whatever it is that I need to define so that whenever I try the guest system's ip address form the host, it will use the vmnet1 or vmnet8 interface define by vmware and bypass the dns configuration of my local area network. I'd also like to know what to do incase I want to change ip addresses on the guest machine without having oracle go haywire (I've noticed a few folders on the structure which are specific for the very first IP Address)... Any help would be appreciated. Thanks in advance.

    Read the article

  • [SC] DeleteService FAILED 1072

    - by Fuangwith S.
    Last time I create WAS profile and WASService then I try to config and run many script for learn how to config WAS, Finally it crash so i use wasprofile delete this profile and forgot delete WASService. Now I found IBM Webphere Application Server service display in services.msc list, so I tried to delete it with WASService.exe -remove command and windows SC command but I got message C:\Program Files\IBM\WebSphere\AppServer\bin>sc delete "IBMWAS61Service - DEV" [SC] DeleteService FAILED 1072: The specified service has been marked for deletion.

    Read the article

  • Nhibernate 2.1 and mysql 5 - InvalidCastException on Setup

    - by Nash
    Hello there, I am trying to use NHibernate with Spring.Net und mySQL 5. However, when setting up the connection and creating the SessionFactoryObject, I get this InvalidCastException: NHibernate seems to cast MySql.Data.MySqlClient.MySqlConnection to System.Data.Common.DbConnection which causes the exception. System.InvalidCastException wurde nicht behandelt. Message="Das Objekt des Typs \"MySql.Data.MySqlClient.MySqlConnection\" kann nicht in Typ \"System.Data.Common.DbConnection\" umgewandelt werden." Source="NHibernate" StackTrace: bei NHibernate.Tool.hbm2ddl.SuppliedConnectionProviderConnectionHelper.Prepare() in c:\CSharp\NH\nhibernate\src\NHibernate\Tool\hbm2ddl\SuppliedConnectionProviderConnectionHelper.cs:Zeile 25. bei NHibernate.Tool.hbm2ddl.SchemaMetadataUpdater.GetReservedWords(Dialect dialect, IConnectionHelper connectionHelper) in c:\CSharp\NH\nhibernate\src\NHibernate\Tool\hbm2ddl\SchemaMetadataUpdater.cs:Zeile 43. bei NHibernate.Tool.hbm2ddl.SchemaMetadataUpdater.Update(ISessionFactory sessionFactory) in c:\CSharp\NH\nhibernate\src\NHibernate\Tool\hbm2ddl\SchemaMetadataUpdater.cs:Zeile 17. bei NHibernate.Impl.SessionFactoryImpl..ctor(Configuration cfg, IMapping mapping, Settings settings, EventListeners listeners) in c:\CSharp\NH\nhibernate\src\NHibernate\Impl\SessionFactoryImpl.cs:Zeile 169. bei NHibernate.Cfg.Configuration.BuildSessionFactory() in c:\CSharp\NH\nhibernate\src\NHibernate\Cfg\Configuration.cs:Zeile 1090. bei OrmTest.Program.Main(String[] args) in C:\Users\Max\Documents\Visual Studio 2008\Projects\OrmTest\OrmTest\Program.cs:Zeile 24. bei System.AppDomain._nExecuteAssembly(Assembly assembly, String[] args) bei System.AppDomain.ExecuteAssembly(String assemblyFile, Evidence assemblySecurity, String[] args) bei Microsoft.VisualStudio.HostingProcess.HostProc.RunUsersAssembly() bei System.Threading.ThreadHelper.ThreadStart_Context(Object state) bei System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) bei System.Threading.ThreadHelper.ThreadStart() InnerException: I am using the programmatically setup approach in order to get a quick NHibernate Setup. Here is the setup Code: Configuration config = new Configuration(); Dictionary props = new Dictionary(); props.Add("dialect", "NHibernate.Dialect.MySQL5Dialect"); props.Add("connection.provider", "NHibernate.Connection.DriverConnectionProvider"); props.Add("connection.driver_class", "NHibernate.Driver.MySqlDataDriver"); props.Add("connection.connection_string", "Server=localhost;Database=orm_test;User ID=root;Password=password"); props.Add("proxyfactory.factory_class", "NHibernate.ByteCode.Spring.ProxyFactoryFactory, NHibernate.ByteCode.Spring"); config.AddProperties(props); config.AddFile("Person.hbm.xml"); ISessionFactory factory = config.BuildSessionFactory(); ISession session = factory.OpenSession(); Is something missing? I downloaded the current mysql Connector from the mysql Website.

    Read the article

  • java 7 upgrade and hibernate annotation processor error

    - by Bill Turner
    I am getting the following warning, which seems to be triggering a subsequent warning and an error. I have been googling like mad, though have not found anything that makes it clear what it is I should do to resolve this. This issue occurs when I execute an Ant build. I am trying to migrate our project to Java 7. I have changed all the source='1.6' and target="1.6" to 1.7. I did find this related article: Forward compatible Java 6 annotation processor and SupportedSourceVersion It seems to indicate that I should build the Hibernate annotation processor jar myself, compiling it with with 1.7. It does not seem I should be required to do so. The latest version of the class in question (in hibernate-validator-annotation-processor-5.0.1.Final.jar) has been compiled with 1.6. Since the code in said class refers to SourceVersion.latestSupported(), and the 1.6 of that returns only RELEASE_6, there does not seem to be a generally available solution. Here is the warning: [javac] warning: Supported source version 'RELEASE_6' from annotation processor 'org.hibernate.validator.ap.ConstraintValidationProcessor' less than -source '1.7' And, here are the subsequent warnings/error. [javac] warning: No processor claimed any of these annotations: javax.persistence.PersistenceContext,javax.persistence.Column,org.codehaus.jackson.annotate.JsonIgnore,javax.persistence.Id,org.springframework.context.annotation.DependsOn,com.trgr.cobalt.infrastructure.datasource.Bucketed,org.codehaus.jackson.map.annotate.JsonDeserialize,javax.persistence.DiscriminatorColumn,com.trgr.cobalt.dataroom.authorization.secure.Secured,org.hibernate.annotations.GenericGenerator,javax.annotation.Resource,com.trgr.cobalt.infrastructure.spring.domain.DomainField,org.codehaus.jackson.annotate.JsonAutoDetect,javax.persistence.DiscriminatorValue,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactionMandatory,org.springframework.stereotype.Repository,javax.persistence.GeneratedValue,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactional,org.hibernate.annotations.Cascade,javax.persistence.Table,javax.persistence.Enumerated,org.hibernate.annotations.FilterDef,javax.persistence.OneToOne,com.trgr.cobalt.dataroom.datasource.config.core.CoreEntity,org.springframework.transaction.annotation.Transactional,com.trgr.cobalt.infrastructure.util.enums.EnumConversion,org.springframework.context.annotation.Configuration,com.trgr.cobalt.infrastructure.spring.domain.UpdatedFields,com.trgr.cobalt.infrastructure.spring.documentation.SampleValue,org.springframework.context.annotation.Bean,org.codehaus.jackson.annotate.JsonProperty,javax.persistence.Basic,org.codehaus.jackson.map.annotate.JsonSerialize,com.trgr.cobalt.infrastructure.spring.validation.Required,com.trgr.cobalt.dataroom.datasource.config.core.CoreTransactionNever,org.springframework.context.annotation.Profile,com.trgr.cobalt.infrastructure.spring.stereotype.Persistor,javax.persistence.Transient,com.trgr.cobalt.infrastructure.spring.validation.NotNull,javax.validation.constraints.Size,javax.persistence.Entity,javax.persistence.PrimaryKeyJoinColumn,org.hibernate.annotations.BatchSize,org.springframework.stereotype.Service,org.springframework.beans.factory.annotation.Value,javax.persistence.Inheritance [javac] error: warnings found and -Werror specified TIA!

    Read the article

  • Could not resolve <fx:Script> to a component implementation.

    - by seref
    Hi, i created project with flexmojos maven archtype..i used flexmojos:flexbuilder and compile/run with FlashBuilder 4 everything is okay but when i try to compile project with flexmojos i got following error: [ERROR] Z:....\src\main\flex\Main.mxml:[6,-1] Could not resolve < fx:Script to a component implementation. [INFO] BUILD FAILURE my mxml: <?xml version="1.0" encoding="utf-8"?> <s:Application xmlns:fx="http://ns.adobe.com/mxml/2009" xmlns:s="library://ns.adobe.com/flex/spark" xmlns:mx="library://ns.adobe.com/flex/mx" width="100%" height="100%" creationComplete="application1_creationCompleteHandler(event)"> <fx:Script> <![CDATA[ import mx.controls.Alert; import mx.events.FlexEvent; protected function application1_creationCompleteHandler(event:FlexEvent):void { Alert.show("success!!!!") } ]]></fx:Script> </s:Application> pom.xml like: ...... <packaging>swf</packaging> ...... <properties> <flex-sdk.version>4.1.0.16076</flex-sdk.version> <flexmojos.version>3.8</flexmojos.version> </properties> ...... <build> <sourceDirectory>src/main/flex</sourceDirectory> <testSourceDirectory>src/test/flex</testSourceDirectory> <plugins> <plugin> <groupId>org.sonatype.flexmojos</groupId> <artifactId>flexmojos-maven-plugin</artifactId> <version>${flexmojos.version}</version> <extensions>true</extensions> <dependencies> <dependency> <groupId>com.adobe.flex</groupId> <artifactId>compiler</artifactId> <version>${flex-sdk.version}</version> <type>pom</type> </dependency> </dependencies> <configuration> <compiledLocales> <locale>en_US</locale> </compiledLocales> <mergeResourceBundle>true</mergeResourceBundle> <accessible>true</accessible> <optimize>true</optimize> <targetPlayer>10.0.0</targetPlayer> <showWarnings>true</showWarnings> <linkReport>true</linkReport> </configuration> </plugin> </plugins> </build> <dependencies> <!-- Flex framework resource bundles --> <dependency> <groupId>com.adobe.flex.framework</groupId> <artifactId>flex-framework</artifactId> <version>${flex-sdk.version}</version> <type>pom</type> </dependency> <!-- Include unit test dependencies. --> <dependency> <groupId>com.adobe.flexunit</groupId> <artifactId>flexunit</artifactId> <version>4.0-rc-1</version> <type>swc</type> <scope>test</scope> </dependency> </dependencies> ....... maven output compiler config : INFO] Flex compiler configurations: -compiler.external-library-path C:\...\.m2\repository\com\adobe\flex \framework\playerglobal\4.1.0.16076\10.0\playerglobal.swc -compiler.include-libraries= -compiler.library-path C:\...\.m2\repository\com\adobe\flex\framework \datavisualization\4.1.0.16076\datavisualization-4.1.0.16076.swc C:\... \.m2\repository\com\adobe\flex\framework\flash-integration \4.1.0.16076\flash-integration-4.1.0.16076.swc C:\...\.m2\repository \com\adobe\flex\framework\flex\4.1.0.16076\flex-4.1.0.16076.swc C:\... \.m2\repository\com\adobe\flex\framework\framework \4.1.0.16076\framework-4.1.0.16076.swc C:\...\.m2\repository\com\adobe \flex\framework\osmf\4.1.0.16076\osmf-4.1.0.16076.swc C:\... \.m2\repository\com\adobe\flex\framework\rpc \4.1.0.16076\rpc-4.1.0.16076.swc C:\...\.m2\repository\com\adobe\flex \framework\spark\4.1.0.16076\spark-4.1.0.16076.swc C:\... \.m2\repository\com\adobe\flex\framework\sparkskins \4.1.0.16076\sparkskins-4.1.0.16076.swc C:\...\.m2\repository\com\adobe \flex\framework\textLayout\4.1.0.16076\textLayout-4.1.0.16076.swc C: \...\.m2\repository\com\adobe\flex\framework\utilities \4.1.0.16076\utilities-4.1.0.16076.swc C:\...\.m2\repository\com\adobe \flex\framework\datavisualization \4.1.0.16076\datavisualization-4.1.0.16076-en_US.rb.swc C:\... \.m2\repository\com\adobe\flex\framework\framework \4.1.0.16076\framework-4.1.0.16076-en_US.rb.swc C:\...\.m2\repository \com\adobe\flex\framework\osmf\4.1.0.16076\osmf-4.1.0.16076- en_US.rb.swc C:\...\.m2\repository\com\adobe\flex\framework\rpc \4.1.0.16076\rpc-4.1.0.16076-en_US.rb.swc C:\...\.m2\repository\com \adobe\flex\framework\spark\4.1.0.16076\spark-4.1.0.16076-en_US.rb.swc C:\...\.m2\repository\com\adobe\flex\framework\textLayout \4.1.0.16076\textLayout-4.1.0.16076-en_US.rb.swc C:\...\.m2\repository \com\adobe\flex\framework\flash-integration\4.1.0.16076\flash- integration-4.1.0.16076-en_US.rb.swc C:\...\.m2\repository\com\adobe \flex\framework\playerglobal\4.1.0.16076\playerglobal-4.1.0.16076- en_US.rb.swc -compiler.theme Z:\.....\target\classes\configs\themes\Spark \spark.css -compiler.accessible=true -compiler.allow-source-path-overlap=false -compiler.as3=true -compiler.debug=false -compiler.es=false -compiler.fonts.managers flash.fonts.JREFontManager flash.fonts.BatikFontManager flash.fonts.AFEFontManager flash.fonts.CFFFontManager -compiler.fonts.local-fonts-snapshot Z:\.....\target\classes \fonts.ser -compiler.keep-generated-actionscript=false -licenses.license flashbuilder4 952309948800588759250406 -licenses.license flexbuilder4.displayedStartPageAtLeastOneTime true -compiler.locale en_US -compiler.optimize=true -compiler.source-path Z:\.....\src\main\flex -compiler.strict=true -use-network=true -compiler.verbose-stacktraces=false -compiler.actionscript-file-encoding UTF-8 -target-player 10.0.0 -default-background-color 8821927 -default-frame-rate 24 -default-script-limits 1000 60 -default-size 500 375 -compiler.headless-server=false -compiler.keep-all-type-selectors=false -compiler.use-resource-bundle-metadata=true -metadata.date Fri Mar 04 14:04:37 EET 2011 -metadata.localized-title Main x-default -verify-digests=true -compiler.namespaces.namespace+=http://ns.adobe.com/mxml/2009,Z:\..... \target\classes\config-4.1.0.16076\mxml-2009-manifest.xml -compiler.namespaces.namespace+=library://ns.adobe.com/flex/spark,Z: \.....\target\classes\config-4.1.0.16076\spark-manifest.xml -compiler.namespaces.namespace+=library://ns.adobe.com/flex/mx,Z:\..... \target\classes\config-4.1.0.16076\mx-manifest.xml -compiler.namespaces.namespace+=http://www.adobe.com/2006/mxml,Z:\..... \PozitronUI\target\classes\config-4.1.0.16076\mxml-manifest.xml - static-link-runtime-shared-libraries=false -load-config= -metadata.language+=en_US any help... regards,

    Read the article

  • Invoking a WCF service using claims based authentication

    - by ashwnacharya
    I have a WCF service deployed in a server machine. We are using claims based authentication to authenticate the WCF service caller. The WCF service is restricted by using IIS Authorization rules. How do I programmatically invoke the WCF service using .NET? The client app uses a proxy generated using SVCUtil. calling the service reads the credentials from a configuration file (not the app.config file, in fact the client application does not have a *.config file).

    Read the article

  • C# Problem with Settings.Reload() and Settings.Save() Settings not loading

    - by galford13x
    I have a strange issue that I can't figure out. I have a custom settings class that inherits ApplicationSettingsBase. It has a user scoped settings as shown below. /// <summary> /// The Last Active Account /// </summary> [UserScopedSettingAttribute()] public AccountKeyClass ActiveAccount { get { try { return (AccountKeyClass)this["ActiveAccount"]; } catch(Exception error){} return null; } set { this["ActiveAccount"] = value; if (!this.AccountList.Contains(value)) { //this.AccountList.Add(value); } } } /// <summary> /// Account List /// Key: UserID /// Value: AccountKeyClass /// </summary> [UserScopedSettingAttribute()] public List<AccountKeyClass> AccountList { get { try { if(this["AccountList"] != null) return (List<AccountKeyClass>)this["AccountList"]; } catch(Exception error){} return null; } set { this["AccountList"] = value; } } I have two forms, a Main form and a Settings form in which to change application settings. When I creating the SettingsForm and change AccountList Settings value, the user.config file changes as excepected. My Apply/Ok button for my SettingsForm calls Settings.Save() then Settings.Reload() then closes the form. The problem is that when .Reload() is called, the Settings.AccountList becomes null. Whats more is that the user.config file never changes, if i close the application and reopen, the user.config file is still correct, but the Settings.AccountList is never read in. The Settings.AccountList is read in if i never call the .Reload() however. Update: If I create a List and Save(); from my MainForm, then the AccountList will be read in from my user.config fine. However If I add to the AccountList using my secondary form (SettingsForm) and call Save() then the next time the application is run the settings are not read in and a null value is returned in it's place. This happens even if I do not use Reload(). I think the problem has something to do with using the Generic List<. The AccountKeyClass that is being saved is saved as Serialized XML.

    Read the article

  • PHP SimpleXML recursive function to list children and attibutes

    - by Phill Pafford
    I need some help on the SimpleXML calls for a recursive function that lists the elements name and attributes. Making a XML config file system but each script will have it's own config file as well as a new naming convention. So what I need is an easy way to map out all the elements that have attributes, so like in example 1 I need a simple way to call all the processes but I don't know how to do this without hard coding the elements name is the function call. Is there a way to recursively call a function to match a child element name? I did see the xpath functionality but I don't see how to use this for attributes. Any ideas? Also does the XML in the examples look correct? can I structure my XML like this? Example 1: <application> <processes> <process id="123" name="run batch A" /> <process id="122" name="run batch B" /> <process id="129" name="run batch C" /> </processes> <connections> <databases> <database usr="test" pss="test" hst="test" dbn="test" /> </databases> <shells> <ssh usr="test" pss="test" hst="test-2" /> <ssh usr="test" pss="test" hst="test-1" /> </shells> </connections> </application> Example 2: <config> <queues> <queue id="1" name="test" /> <queue id="2" name="production" /> <queue id="3" name="error" /> </queues> </config> Pseudo code: // Would return matching process id getProcess($process_id) { return the process attributes as array that are in the XML } // Would return matching DBN (database name) getDatabase($database_name) { return the database attributes as array that are in the XML } // Would return matching SSH Host getSSHHost($ssh_host) { return the ssh attributes as array that are in the XML } // Would return matching SSH User getSSHUser($ssh_user) { return the ssh attributes as array that are in the XML } // Would return matching Queue getQueue($queue_id) { return the queue attributes as array that are in the XML } EDIT: Can I pass two parms? on the first method you have suggested @Gordon public function findProcessById($id, $name) { $attr = false; $el = $this->xml->xpath("//process[@id='$id']"); // How do I also filter by the name? if($el && count($el) === 1) { $attr = (array) $el[0]->attributes(); $attr = $attr['@attributes']; } return $attr; }

    Read the article

  • ruby script/server not reading RAILS_ENV option

    - by iwan
    Hello, I tried to run ruby script/server RAILS_ENV=production but somehow it always try to read "development" config.. nothings wrong with RAKE XXX RAILS_ENV=production (trying to read production config). Any idea how to troubleshoot? I have my other rails app in the same machine and it works fine. The problem above only happen for redmine rails. Thanks in advance. -iwan

    Read the article

  • MvcBuildViews true with Entity Framework in ASP.NET MVC 2

    - by Alper Ozcetin
    Hi everybody, In VS 2010, changing true in a MVC2 project's .csproj file causes an error if you are using Entity Framework. Could not load type 'System.Data.Entity.Design.AspNet.EntityDesignerBuildProvider'. C:\Windows\Microsoft.NET\Framework\v4.0.30319\Config\web.config 129 I want to build views while I'm debugging, and I also want my project compile! Any ideas? Thanks.

    Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >